Asus II/CELERON P2V User Manual

® P2V Pentium ® II/Celeron ™ Motherboard USER’S MANUAL
ASUS P2V User’ s Manual 2 USER'S NOTICE Product Name: ASUS P2V Manual Revision: 1.01 E384 Release Date: May 1999 No part of this manual, including the products and software described in it, may be repro- duced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup pur- poses, without the express written permission of ASUST eK COMPUTER INC. (“ASUS”). ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT W ARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED W ARRANTIES OR CONDITIONS OF MERCHANT ABILITY OR FITNESS FOR A P AR- TICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT , SPECIAL, INCIDEN- T AL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DA T A, INTERRUPTION OF BUSI- NESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT . Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair , modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. Products and corporate names appearing in this manual may or may not be registered trade- marks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe. • Intel, LANDesk, Pentium, and Celeron are trademarks of Intel Corporation. • IBM and OS/2 are registered trademarks of International Business Machines. • Symbios is a registered trademark of Symbios Logic Corporation. • W indows and MS-DOS are registered trademarks of Microsoft Corporation. • Sound Blaster A WE32 and SB16 are trademarks of Creative T echnology Ltd. • Adobe and Acrobat are registered trademarks of Adobe Systems Incorporated. The product name and revision number are both printed on the product itself. Manual revi- sions are released for each product design represented by the digit before and after the period of the manual revision number . Manual updates are represented by the third digit in the manual revision number . For previous or updated manuals, BIOS, drivers, or product release information, contact ASUS at http://www .asus.com.tw or through any of the means indicated on the following page. SPECIFICA TIONS AND INFORMA TION CONT AINED IN THIS MANUAL ARE FUR- NISHED FOR INFORMA TIONAL USE ONL Y , AND ARE SUBJECT TO CHANGE A T ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COM- MITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THA T MA Y APPEAR IN THIS MANUAL, INCLUD- ING THE PRODUCTS AND SOFTW ARE DESCRIBED IN IT . Copyright © 1999 ASUST eK COMPUTER INC. All Rights Reserved.
ASUS P2V User’ s Manual 3 ASUS CONT ACT INFORMA TION ASUST eK COMPUTER INC. (Asia-Pacific) Marketing Address: 150 Li-T e Road, Peitou, T aipei, T aiwan 1 12 T elephone: 886-2-2894-3447 Fax: 886-2-2894-3449 Email: info@asus.com.tw T echnical Support T el (English): 886-2-2894-3447 ext. 706 T el (Chinese): 886-2-2894-3447 ext. 1 1 1 Fax: 886-2-2895-9254 Email: tsd@asus.com.tw Newsgroup: news2.asus.com.tw WWW : www .asus.com.tw FTP: ftp.asus.com.tw/pub/ASUS ASUS COMPUTER INTERNA TIONAL (America) Marketing Address: 6737 Mowry A venue, Mowry Business Center , Building 2 Newark, CA 94560, USA Fax: 1-510-608-4555 Email: info-usa@asus.com.tw T echnical Support Fax: 1-510-608-4555 BBS: 1-510-739-3774 Email: tsd-usa@asus.com.tw WWW : www .asus.com FTP: ftp.asus.com.tw/pub/ASUS ASUS COMPUTER GmbH (Europe) Marketing Address: Harkort Str . 25, 40880 Ratingen, BRD, Germany T elephone: 49-2102-44501 1 Fax: 49-2102-442066 Email: sales@asuscom.de T echnical Support Hotline: 49-2102-499712 BBS: 49-2102-448690 Email: tsd@asuscom.de WWW : www .asuscom.de FTP: ftp.asuscom.de/pub/ASUSCOM
ASUS P2V User’ s Manual 4 CONTENTS I. INTRODUCTION 7 How this Manual is Or ganized ........................................................... 7 Item Checklist ..................................................................................... 7 II. FEA TURES 8 Features of the ASUS P2V Motherboard ............................................ 8 The ASUS P2V Motherboard ........................................................ 9 III. INST ALLA TION 10 Layout of the ASUS P2V Motherboard ............................................ 10 Installation Steps ............................................................................... 12 1. Jumpers ......................................................................................... 12 Jumper Settings ........................................................................... 13 2. System Memory (DIMM) ............................................................. 17 DIMM Memory Installation Procedures: .............................. 18 3. Central Processing Unit (CPU) .................................................... 19 Universal Retention Mechanism ........................................... 19 Heatsinks ............................................................................... 19 Installing the Processor ............................................................... 20 ASUS Smart Thermal Solutions ............................................ 22 Recommended Heatsinks for Slot 1 Processors .................... 23 4. Expansion Cards ........................................................................... 24 Expansion Card Installation Procedure ................................. 24 Assigning IRQs for Expansion Cards .................................... 24 Assigning DMA Channels for ISA Cards .............................. 25 ISA Cards and Hardware Monitor ......................................... 25 5. External Connectors ..................................................................... 26 Power Connection Procedures .......................................................... 33 IV . BIOS SOFTW ARE 34 Flash Memory W riter Utility ............................................................ 34 Main Menu .................................................................................. 34 Managing and Updating Y our Motherboard’ s BIOS ................... 36 6. BIOS Setup .................................................................................. 37 Load Defaults ........................................................................ 38 Standard CMOS Setup ................................................................ 38 Details of Standard CMOS Setup: ......................................... 38 BIOS Features Setup ................................................................... 41 Details of BIOS Features Setup ............................................. 41
ASUS P2V User’ s Manual 5 CONTENTS Chipset Features Setup ................................................................ 44 Details of Chipset Features Setup .......................................... 44 Power Management Setup ........................................................... 47 Details of Power Management Setup .................................... 47 PNP and PCI Setup ..................................................................... 50 Details of PNP and PCI Setup ............................................... 50 Load BIOS Defaults .................................................................... 52 Load Setup Defaults .................................................................... 52 Supervisor Password and User Password ................................... 53 IDE HDD Auto Detection ........................................................... 54 Save & Exit Setup ....................................................................... 55 Exit W ithout Saving .................................................................... 55 V . DESKT OP MANAGEMENT 56 Desktop Management Interface (DMI) ............................................. 56 Introducing the ASUS DMI Configuration Utility ................ 56 System Requirements ............................................................ 56 Using the ASUS DMI Configuration Utility ......................... 57 Using the ASUS DMI Configuration Utility ......................... 57 VI. ASUS LAN Card 59 ASUS PCI-L101 Fast Ethernet Card ................................................ 59 Features ............................................................................................. 60 Software Driver Support ............................................................. 60 Question and Answer .................................................................. 60
ASUS P2V User’ s Manual 6 FCC & DOC COMPLIANCE Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa- tion. This equipment generates, uses and can radiate radio frequency ener gy and, if not installed and used in accordance with manufacturer's instructions, may cause harmful interference to radio communications. However , there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the inter - ference by one or more of the following measures: • Re-orient or relocate the receiving antenna. • Increase the separation between the equipment and receiver . • Connect the equipment to an outlet on a circuit dif ferent from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. W ARNING! Any changes or modifications to this product not expressly ap- proved by the manufacturer could void any assurances of safety or performance and could result in violation of Part 15 of the FCC Rules. Canadian Department of Communications Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Cana- dian Department of Communications. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
ASUS P2V User’ s Manual 7 I. INTRODUCTION I. INTRODUCTION Manual / Checklist How this Manual is Organized This manual is divided into the following sections: I. Introduction: Manual information and checklist II. Featur es: Information and specifications concerning this product III. Installation: Instructions on setting up the motherboard IV . BIOS Softwar e: Instructions on setting up the BIOS software V . Support Softwar e: Information on the included support software Item Checklist Please check that your package is complete. If you discover damaged or missing items, please contact your retailer . (1) ASUS Motherboard (1) Universal Retention M echanism for SECC/SECC2/SEPP (1) IDE ribbon cable for master and slave drives (1) Floppy ribbon cable for (1) 5.25inch floppy and (2) 3.5inch floppies (1) Bag of spare jumper caps (1) Support CD with drivers and utilities (1) User ’ s manual S-P2F AN or P2T -Cable for Slot 1 processors (optional) IrDA-compliant infrared module (optional) ASUS PCI-L101 W ake-on-LAN 10/100 Ethernet Card (optional)
8 ASUS P2V User’ s Manual Features of the ASUS P2V Motherboard The ASUS P2V is carefully designed for the demanding PC user who wants ad- vanced features processed by the fastest CPU. • Multi-Speed: Supports Intel Pentium ® II (2 33 to 500M H z) and Celeron TM (266MHz and faster) processors. • Multi-Cache: Supports processors with or without Pipelined Burst Level 2 cache. • VIA Chip set: Features VI A ’s VT82C693 chipset with I/O subsystems and front-side bus (FSB) platform, which boosts the traditional 66-MHz internal bus speed to 100MHz. • Enhanced ACPI and Anti-Boot V irus BIOS: Features a programmable BIOS, of fering en- hanced ACPI for W indows 98 compatibility , built-in hardware-based virus protection through T rend ChipA way V irus, and autodetection of most devices for virtually automatic setup. • PC100 Memory Support: Equipped with three DIMM sockets to support Intel PC100- compliant SDRAMs (8, 16, 32, 64, 128 or 256 MB) up to 768MB. These new SDRAMs are necessary to meet the enhanced 100MHz bus speed requirement. • Thermal Sensor Connector with Optional Sensor: Accurately detects the CPU tem- perature of processors with the ASUS Smart Fan or the Intel boxed processor heatsink with fan when connected to an ASUS P2T -Cable. • Hardware Monitoring: Provides a convenient utility to monitor your system’ s vital components/activities, such as fan rotations, voltages, and temperatures. • W ake-On-LAN: Supports W ake-On–LAN activity with special network cards, such as the ASUS PCI-L101 10/100 Fast Ethernet PCI card. • AGP Slot: Supports Accelerated Graphics Port cards for high performance, component level interconnect tar geted at 3D graphical display applications. • SMBus: Features the System Management Bus interface, which is used to physically transport commands and information between SMBus devices. • P CI & I S A Expansion Slots: Provides f our 32-bit PCI and three 16-bit ISA slots. • Intelligence: Supports Keyboard Power Up, Fan Status Monitoring and Alarm, T em- perature Monitoring and Alert, V oltage Monitoring and Alert, System Resources Alert, Intel LANDesk Client Manager (LDCM), and ASUS PC Probe software. • Super Multi-I/O: Provides two high-speed UAR T compatible serial ports and one parallel port with EPP and ECP capabilities. UAR T2 can also be directed from COM2 to the Infra- red Module for wireless connections. • Desktop Management Interface (DMI): Supports DMI through BIOS, which allows hardware to communicate within a standard protocol creating a higher level of compat- ibility . (Requires DMI-enabled components.) (See section V) • Ultra DMA/33 Bus Master IDE: Comes with an onboard PCI Bus Master IDE controller with two connectors that support four IDE devices in two channels, supports UltraDMA/33, PIO Modes 3 and 4 and Bus Master IDE DMA Mode 2, and supports Enhanced IDE devices, such as T ape Backup, CD-ROM, and LS-120 drives. • Universal Retention Mechanism: Supports a Pentium ® II processor packaged in a Single Edge Contact Cartridge (SECC/SECC2) or a Celeron TM processor packaged in a Single Edge Processor Package (SEPP). • SCSI BIOS: Supports optional ASUS SCSI controller cards through onboard SYMBIOS firmware. • IrDA: S upports an optional infrared port module for wireless interface. • Concurr ent PCI: Allows multiple PCI transfers from PCI master buses to memory to CPU. II. FEA TURES Specifications II. FEA TURES
ASUS P2V User’ s Manual 9 The ASUS P2V Motherboard II. FEA TURES II. FEA TURES Motherboard Parts T : USB Port 1 B: USB Port 2 B: COM 1 B: COM 2 Programmable 2Mbit Flash EEPROM 3 ISA Slots T : PS/2 Mouse B: PS/2 Keyboard T : Parallel B: Serial 3 DIMM Sockets Chipset CPU Slot 1 A TX Power Connector 4 PCI Slots Universal Folding Retention Mechanism Accelerated Graphics Port W ake-On-LAN Connector Hardware Monitoring ASIC CPU Thermal Sensor Connector
10 ASUS P2V User’ s Manual III. INST ALLA TION Layout of the ASUS P2V Motherboard FLOPPY SECONDARY IDE PRIMARY IDE CR2032 3V Lithium Cell (CMOS Power) CPU_F AN DIMM Socket 1 (64/72 bit, 168 pin module) DIMM Socket 2 (64/72 bit, 168 pin module) DIMM Socket 3 (64/72 bit, 168 pin module) Accelerated Graphics Port PCI Slot 4 ISA Slot 3 VIA VT82C596A PCIset VIA VT82C693 Chipset Flash EEPROM (Programable BIOS) PWR_F AN CHA_FAN Hardware Monitor A TX Power Conenctor CPU Slot 1 Panel Connectors Infrared Connector IDE LED USB PS/2 TOP: USB 1 BOTTOM: USB 2 Multi-I/O R Wake-On-LAN Connector BUS FREQ BF2 BF3 BF1 BF0 CLRTC BUS FREQ FS1 FS2 FS0 ISA Slot 1 ISA Slot 2 PCI Slot 3 PCI Slot 2 PCI Slot 1 COM 1 Parallel Port COM 2 TOP: Mouse BOTTOM: Keyboard Keyboard Power ASUS ASIC SMB Connector JTPWR CHASIS JTCPU FS3 AGPFS VIO Board Layout III. INST ALLA TION
ASUS P2V User’ s Manual 11 III. INST ALLA TION Jumpers 1) KBPWR p. 12 Keyboard Power 2) AGPFS p. 13 AGP Frequency Selection 3) VIO p. 13 V oltage Input/Output Selection 4) FS0, FS1, FS2, FS3 p. 14 CPU External Clock (BUS) Frequency Selection 5) BF0, BF1, BF2, BF3 p . 14 CPU Core:BUS Frequency Multiple Expansion Slots/Sockets 1) System Memory p. 17 System Memory Support 2) DIMM Sockets p. 18 DIMM Memory Module Support 3) CPU Slot 1 p. 19 Pentium II/Celeron C PU Support 4 ) SLOT1, SLOT2, SLOT3 p . 2 4 16-bit ISA Bus Expansion Slots * 5 ) PCI1, PCI2,PCI3, PCI4 p. 24 32-bit PCI Bus Expansion Slots 6) AGP p. 25 Accelerated Graphics Port Hardwar e Monitor 1) JTPWR, JTCPU p . 23 Thermal Sensor Connector Connectors 1) PS2KBMS p. 26 PS/2 Keyboard C onnector (6-pin female) 2) PS2KBMS p. 26 PS/2 Mouse C onnector (6-pin f emale) 3) P ARALLEL p . 27 Parallel (Printer) Port Connector (25-pin f emale) 4) COM1, COM2 p . 27 Serial Port COM1 & COM2 ( two 9-pin male) 5) FLOPPY p. 2 7 Floppy Drive C onnector (34-pin b lock) 6) USB p. 28 Universal Serial BUS Ports 1 & 2 (two 4-pin female) 7) Primary/Secondar y IDE p. 28 Primary/Secondary IDE C onnector (40-pin blocks) 8) IDELED p . 28 IDE LED Activity Light (2 pins) 9 ) CHA_, PWR_, CPU_F AN p . 2 9 Chassis, Power Supply , CPU Fan Power Lead (3-pin b lock) 10) CHASIS p. 29 Chassis Intrusion Alarm Lead (4-1 pins) 1 1) IR p . 30 Infrared Port Module Connector (5 pins) 12) A TXPWR p . 30 A TX Motherboard Power Connector (20-pin block) 13) WOL_CON p. 31 W ake on LAN Connector (3 pins) 14) SMB p. 31 SMBus Connector (5-1 pins) 15) MSG.LED (P ANEL) p . 32 System Message LED (2 pins) 1 6 ) SMI (P ANEL) p . 32 SMI Switch Lead (2 pins) 17) PWR.SW (P ANEL) p. 32 A TX Power & Soft-Off Switch Lead (2 pins) 1 8 ) RESET (P ANEL) p. 32 Reset Switch Lead (2 pins) 19) PWR.LED ( P ANEL ) p. 32 System Power LED Lead (3 pins) 20) KEYLOCK ( P ANEL ) p. 32 Keyboard Lock Switch Lead (2 pins) 21) SPEAKER (P ANEL) p. 32 Speaker Output Connector (4 pins) * The onboard hardware monitor uses the address 290H-297H so legacy ISA cards must not use this address otherwise conflicts will occur . Board Layout III. INST ALLA TION
12 ASUS P2V User’ s Manual III. INST ALLA TION Jumpers III. INST ALLA TION Installation Steps Before using your computer , you must complete the following steps: 1. Set Jumpers 2. Install Memory Modules 3. Install the Central Processing Unit (CPU) 4. Install Expansion Cards 5. Connect Ribbon Cables, Cabinet W ires, and Power Supply 6. Setup the BIOS Software 1. Jumpers W ARNING! Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips. T o protect them against damage from static electric- ity , you should follow some precautions whenever you work on your computer . 1. Unplug your computer when working on the inside. 2. Use a grounded wrist strap before handling computer components. If you do not have one, touch both of your hands to a safely grounded object or to a metal object, such as the power supply case. 3. Hold components by the edges and try not to touch the IC chips, leads or connectors, o r other components. 4. Place components on a grounded antistatic pad or on the bag that came with the component whenever the components are separated from the system. Jumper Settings 1. Keyboard Power Up (KBPWR) This allows you to disable or enable the keyboard power up function. Set to Enable if you want to use your keyboard (by pressing <Spacebar>) to power up your computer . This feature requires an A TX power supply that can supply at least 300mA on the 5VSB lead and the new ACPI BIOS support. The default is set to Disable because not all computers have the appropriate A TX power sup- ply . Y our computer will not function if you set this to Enable and if you do not have the right A TX power supply . R Disable 1 2 3 KBPWR Enable 1 2 3 P2V Keyboard Power Up
ASUS P2V User’ s Manual 13 III. INST ALLA TION III. INST ALLA TION Jumpers 2. AGP Frequency Selection (AGPFS) This option sets the frequency ratio between the AGP bus frequency and the CPU bus frequency . The default sets the AGP frequency to 2/3 of the CPU bus or host frequency . IMPOR T ANT : Due to limitations in the VIA Apollo Pro Plus chipset, the AGP frequency should only be set to twice that of the PCI frequency (AGP Frequency=2 x PCI Frequency). Thus AGP frequency must be set in conjunction with the CPU bus frequency to avoid this limitation. (See next page for frequency settings.) R P2V AGP Frequency Selection AGPFS AGP Frequency = 2/3 CPU Bus or Host Frequency (2:3) AGPFS AGP Frequency = CPU Bus or Host Frequency (1:1) 1 2 3 1 2 3 (Default) W ARNING! AGP bus frequencies above 66MHz exceed the specifications for the AGP interface and are not guaranteed to be stable. 3. V oltage Input/Output Selection (VIO) Th is jumper allows you to select the voltage supplied to the DRAM, chipset, and AGP . R P2V V oltage Input/Output Selection VIO 12 3 (Default) VIO 12 3 (T est) W ARNING! Using a higher voltage ( T est setting) may help when overclocking but may result in the shortening of your computer component’ s life. Use default setting.
14 ASUS P2V User’ s Manual III. INST ALLA TION Jumpers III. INST ALLA TION BF2 BF1 BF3 CPU Core:BUS Frequency Multiple P2V CPU Settings R BF0 BF2 BF1 BF3 BF0 BF2 BF1 BF3 BF0 BF2 BF1 BF3 BF0 BF2 BF1 BF3 BF0 BF2 BF1 BF3 BF0 BF2 BF1 BF3 BF0 2.0x (2/1) 2.5x (5/2) 3.0X (3/1) 3.5X (7/2) 4.0X (4/1) 4.5X (9/2) 5.0X (5/1) 2 1 3 2 1 3 2 1 3 2 1 3 2 1 3 2 1 3 BF2 BF1 BF3 BF0 BF2 BF1 BF3 BF0 BF2 BF1 BF3 BF0 BF2 BF1 BF3 BF0 BF2 BF1 BF3 BF0 BF2 BF1 BF3 BF0 5.5x (1 1/2) 6.0x (6/1) 6.5X (13/2) 7.0X (7/1) 7.5X (15/2) 8.0X (8/1) 2 1 3 2 1 3 2 1 3 2 1 3 2 1 3 FS1 FS2 FS0 FS1 FS2 FS0 FS1 FS2 FS0 1 2 3 FS1 FS2 FS0 1 2 3 FS1 FS2 FS0 1 2 3 FS1 FS2 FS0 103MHz 34.3MHz CPU External Clock (BUS) Frequency Selection 66.8MHz 33.4MHz 75MHz 37.5MHz 83.3MHz 41.65MHz 100.3MHz 33.43MHz 105MHz 35MHz FS3 FS3 FS3 1 2 3 1 2 3 FS3 FS3 FS3 FS1 FS2 FS0 FS1 FS2 FS0 FS1 FS2 FS0 1 2 3 FS1 FS2 FS0 1 2 3 FS1 FS2 FS0 1 2 3 FS1 FS2 FS0 133MHz 33.3MHz 1 15MHz 38.33MHz 120MHz 40MHz 124MHz 31MHz 124MHz 41.33MHz 133MHz 44.33MHz FS3 FS3 FS3 1 2 3 1 2 3 FS3 FS3 FS3 CPU PCI FS1 FS2 FS0 FS1 FS2 FS0 1 10MHz 36.67MHz 1 12MHz 37.33MHz FS3 FS3 1 2 3 CPU PCI 1 2 3 1 2 3 FS1 FS2 FS0 1 2 3 FS1 FS2 FS0 140MHz 35MHz 150MHz 37.5MHz FS3 FS3 4. CPU Bus Frequency (FS0, FS1, FS2, FS3) This option tells the clock generator what frequency to send to the CPU, DRAM, and chipset. This allows the selection of the CPU’ s External frequency (or BUS Clock ). The BUS Clock multiplied by the BUS Ratio equals the CPU’ s Internal frequency (the ad- vertised CPU speed). 5. CPU Core:BUS Fr equency Multiple (BF0, BF1, BF2, BF3) This option sets the frequency ratio between the Internal frequency of the CPU and the CPU’ s External frequency . These must be set in conjunction with the CPU Bus Fr equency . W ARNING! Frequencies above 1 00 MH z exceed the specifications for the onboard chipset and are not guaranteed to be stable.
ASUS P2V User’ s Manual 15 NOTES • Overclocking your processor is not recommended. It may result in a slower speed. V oltage Regulator Output Selection (VID) is not needed for the Pentium III / II / Celeron processors because they send VID signals directly to the onboard power controller . • For updated processor settings, visit the ASUS web site (see ASUS CONT ACT INFORMA TION for URLs). (BUS Freq.) (Freq. Mult.) Intel CPU Model Freq. Mult. BUS F . FS0 FS1 FS2 FS3 BF0 BF1 BF2 BF3 Pentium III 550MHz 5.5x 100MHz [1-2] [1-2] [1-2] [2-3] [1-2] [1-2] [1-2] [2-3] Pentium III 500MHz 5.0x 100MHz [1-2] [1-2] [1-2] [2-3] [2-3] [1-2] [1-2] [2-3] Pentium III / II 450MHz 4.5x 100MHz [1-2] [1-2] [1-2] [2-3] [1-2] [2-3] [1-2] [2-3] Pentium II 400MHz 4.0x 100MHz [1-2] [1-2] [1-2] [2-3] [2-3] [2-3] [1-2] [2-3] Pentium II 350MHz 3.5x 100MHz [1-2] [1-2] [1-2] [2-3] [1-2] [1-2] [2-3] [2-3] Celeron 466MHz 7.0x 66MHz [1-2] [1-2] [2-3] [2-3] [2-3] [1-2] [2-3] [1-2] Celeron 433MHz 6.5x 66MHz [1-2] [1-2] [2-3] [2-3] [1-2] [2-3] [2-3] [1-2] Celeron 400MHz 6.0x 66MHz [1-2] [1-2] [2-3] [2-3] [2-3] [2-3] [2-3] [1-2] Celeron 366MHz 5.5x 66MHz [1-2] [1-2] [2-3] [2-3] [1-2] [1-2] [1-2] [2-3] Pentium II/Celeron 333MHz 5.0x 66MHz [1-2] [1-2] [2-3] [2-3] [2-3] [1-2] [1-2] [2-3] Pentium II/Celeron 300MHz 4.5x 66MHz [1-2] [1-2] [2-3] [2-3] [1-2] [2-3] [1-2] [2-3] Pentium II/Celeron 266MHz 4.0x 66MHz [1-2] [1-2] [2-3] [2-3] [2-3] [2-3] [1-2] [2-3] Pentium II 233MHz 3.5x 66MHz [1-2] [1-2] [2-3] [2-3] [1-2] [1-2] [2-3] [2-3] Set the jumpers by the Internal speed of your processor a s follows: III. INST ALLA TION Jumpers III. INST ALLA TION
16 ASUS P2V User’ s Manual (This page was intentionally left blank.)
ASUS P2V User’ s Manual 17 III. INST ALLA TION System Memory 2. System Memory (DIMM) This motherboard uses o nly Dual Inline Memory Modules (DIMMs). Three sockets are available for 3.3V olt (power level) unbuffered Synchronous Dynamic Random Access Memory (SDRAM) of either 8, 16, 32, 64, 128 o r 25 6MB to form a memory size between 8MB to 76 8MB. One side (with memory chips) of the DIMM takes up one row on the motherboard. T o utilize the chipset’ s Error Checking and Correction (ECC) feature, you must use a DIMM module with 9 chips per side (standard 8 chips/side 1 EC C chip) and make the proper settings through “Chipset Features Setup” in IV . BIOS SOFTW ARE . Memory speed setup is recommended through SDRAM Configuration under “Chipset Features Setup”. IMPOR T ANT (see General DIMM Notes below) • SDRAMs used must be compatible with the current Intel PC100 SDRAM specification. Install memory in any combination as follows: DIMM Location 168-pin DIMM T otal Memory Socket 1 (Rows 0&1) SDRAM 8, 16, 32, 64, 128, 256MB x1 Socket 2 (Rows 2&3) SDRAM 8, 16, 32, 64, 128, 256MB x1 Socket 3 (Rows 4&5) SDRAM 8, 16, 32, 64, 128, 256MB x1 T otal System Memory (Max 768MB) = NOTES • At the time this User ’ s Manual was written, 256MB DIMMs are only available as registered memory . • DIMMs that have more than 18 chips are not supported on this motherboard. • For the system CPU bus to operate 100 MHz, use only PC100-compliant DIMMs. When this motherboard operates at 100MHz, most system will not even boot if non- compliant modules are used because of the strict timing issues involved under these speeds. If your DIMMs are not PC100-compliant, set the CPU bus frequency to 66MHz for system stability . • ASUS motherboards support SPD (Serial Presence Detect) DIMMs. This is the memory of choice for best performance vs. stability . • SDRAM chips are generally thinner with higher pin density than EDO (Extended Data Output) chips. • BIOS shows SDRAM memory on bootup screen. • Single-sided DIMMs come in 16, 32, 64,128MB; double-sided come in 32, 64, 128, 256MB. III. INST ALLA TION
18 ASUS P2V User’ s Manual System Memory III. INST ALLA TION III. INST ALLA TION DIMM Memory Installation Procedures: Insert the module(s) as shown. Because the number of pins are different on either side of the breaks, the module will only fit in the orientation as shown. DRAM SIMM modules have the same pin contacts on both sides. SDRAM DIMMs have different pin contacts on each side and therefore have a higher pin density . Lock P2V 168-Pin DIMM Memory Sockets 20 Pins 60 Pins 88 Pins R The DIMMs must be 3.3V olt unbuf fered SDRAMs. T o determine the DIMM type, check the notches on the DIMMs (see figure below). 168-Pin DIMM Notch Key Definitions (3.3V) DRAM Key Position V oltage Key Position Unbuffered RFU Buffered Reserved 3.3V 5.0V The notches on the DIMM will shift between left, center , or right to identify the type and also to prevent the wrong type from being inserted into the DIMM slot on the motherboard. Y ou must tell your retailer the correct DIMM type before purchasing. This motherboard supports four clock signals.
ASUS P2V User’ s Manual 19 III. HARDW ARE SETUP CPU III. H/W SETUP 3. Central Processing Unit (CPU) NOTE: The following pictures are provided for reference purposes only . The ap- pearance of your retention mechanism and fan may be dif ferent from the following examples. Y our motherboard provides a Slot 1 connector for a Pentium ® III processor pack- aged in a Single Edge Contact Cartridge (SECC2), a Pentium ® II processor pack- aged in SECC/SECC2, or a Celeron™ processor packaged in a Single Edge Proces- sor Package (SEPP). An ASUS S370 CPU card can allow Socket 370 processors to be used on any ASUS motherboard with the Slot 1 connector . Heatsinks The recommended heatsinks (see section on recommended heatsinks for Pentium III / II processors for more information) for the boxed Pentium III / II and Celeron processors are those with three-pin fans that can be connected to the fan connectors on the motherboard. W ARNING! Be sure that there is sufficient air circulation across the processor ’ s heatsink by regularly checking that your CPU fan is working. W ithout sufficient circulation, the processor could overheat and damage both the processor and the motherboard. Y ou may install an auxiliary chassis fan, if necessary . Pentium II processor packaged in an SECC with heatsink and fan (top view) Pentium III (in an SECC2) with heatsink and fan NOTE: The SEPP fan (for Celeron processors) is similar to SECC2 fan except that the clamping design is dif ferent. Y our motherboard comes preinstalled with a Universal Retention Mechanism (URM). The URM supports Pentium III / II and Celeron processors. Universal Retention Mechanism (URM) Universal Retention Mechanism
20 ASUS P2V User’ s Manual III. HARDW ARE SETUP CPU III. H/W SETUP 2. Attach the Heatsink NOTE: If provided, you should follow the heatsink attachment instructions that came with your heatsink or processor . The following steps are provided only as a general guide and may not reflect those for your heatsink. The URM is now ready for the installation of your processor . Installing the Processor 1. Unlock the URM’ s Folding Support Arms: The folding support arms of the URM are locked when shipped. Using the SECC fan with the Pentium ® II Push the two lock arms one direction to clamp the heatsink onto the processor and the other direction to release. Using the SECC2 fan with the Pentium ® III Insert the four heatsink’ s pins through the holes of the SECC2. Place the metal clip on the ends of the pins and slide until it locks into place. Unlocked Folding Support Arms Locked Folding Support Arms T o unlock the support arms, simply flip them up to an upright position. Lock Arm Lock Arm Four Pins and metal clip NOTE: The SEPP heatsink and fan (for Intel Celeron processors) is similar to the SECC2 heatsink and fan except that the clamping design is dif ferent.
ASUS P2V User’ s Manual 21 III. HARDW ARE SETUP CPU III. H/W SETUP 3 . Insert the SEC C/SECC2/SEPP SECC with Pentium ® II only: Push the SECC’ s two locks inward until you hear a click (the picture i n step 2 shows the locks in the outward position and inward in the picture below). W ith the heatsink facing the motherboard’ s chipset, push the SECC, SECC2, or SEPP gently but firmly into the Slot 1 connector until it is fully inserted. 4. Secure the SECC/SECC2/SEPP Secure the SECC/SECC2/SEPP in place by pushing the SECC/SECC2/SEPP until it is firmly seated on the Slot 1 connector . SECC with Pentium ® II only: The SECC locks should be outward when se- cured so that the lock shows through the retention mechanism’ s lock holes. SECC2/SEPP Push lock inward SECC SECC SECC2/SEPP CPU fan cable to fan connector CPU fan cable to fan connector CPU fan cable to fan connector CPU fan cable to fan connector Lock hole W ARNING! Make sure the heatsink is mounted tightly against the SECC, SECC2 or SEPP; otherwise, the CPU will overheat. Y ou may install an auxiliary fan to provide adequate circulation across the processor ’ s passive heatsink. Lock hole
22 ASUS P2V User’ s Manual III. HARDW ARE SETUP CPU III. H/W SETUP ASUS Smart Thermal Solutions ASUS provides two smart solutions to Slot 1 CPU thermal problems: the ASUS Smart Fan or ASUS S-P2F AN and the ASUS P2T -Cable . ASUS S-P2F AN The optional ASUS Smart Fan or ASUS S-P2F AN is a CPU fan for a Pentium ® II processor packaged in an SECC. Unlike other CPU thermal solutions, the ASUS S-P2F AN has an integrated thermal sensor located near the center of the CPU heat source. The sensor is optimized by ASUS to give the most accurate reading of the CPU tempera- ture, thus provides the best protection to your computer system. T o Use the ASUS S-P2F AN See 2. Attach the Heatsink on the preceding page for the relevant procedures. Note that the S-P2F AN comes with a rock arm design for easy F AN/CPU installation. ASUS P2T -Cable The optional ASUS P2T -Cable can be used for a Pentium ® III/II processor pack- aged in an SECC2 /SECC or a Celeron™ processor packaged in an SEPP . NOTE: The ASUS P2T -Cable can only be used in a Slot 1 motherboard with a 2-pin thermal sensor connector . T o Use the ASUS P2T -Cable NOTE: The following procedures assume that you have properly attached a heatsink onto an SECC/SECC2/SEPP . 1. Simply peel off the tab from the sensor and then stick the sensor near the middle edge of the Intel boxed processor heatsink with fan (middle) or to either the upper or lower edge of the Celeron™ heatsink (right), as indicated. Sensor Connector Plug Sensor CPU Fan Cable (3 colored wires) Thermal Cable (2 black wires) Ta b Sensor ← OR STICK ABOUT HERE
ASUS P2V User’ s Manual 23 III. HARDW ARE SETUP CPU III. H/W SETUP Recommended Heatsinks for Slot 1 Processors The recommended heatsinks for the Slot 1 processors are those with three-pin fans, such as the ASUS Smart Fan, that can be connected to the motherboard’ s CPU fan connector . These heatsinks dissipate heat more ef ficiently and with an optional hard- ware monitor , they can monitor the fan’ s RPM and use the alert function with the Intel LANDesk Client Manager (LDCM) or the ASUS PC Probe software. SECC Heatsink & Fan SECC2 Heatsink & Fan NOTE: The SEPP heatsink and fan (for Intel Celeron processors) is similar to the SECC2 heatsink and fan except that the clamping design is dif ferent. W ARNING! Do not insert the sensor between the processor and heatsink, other- wise, it will cause damage to the P2T -Cable. IMPOR T ANT! ASUS guarantees accurate readings only for the ASUS Smart Fan and the Intel boxed processor heatsink with fan because both have similar heat distribution and heatsink material. 2. Connect the P2T -Cable to the CPU thermal sensor connector (JTCPU) . P2B-F Thermal Sensor Connectors R JTPWR Power Supply Thermal Sensor Connector JTCPU CPU Thermal Sensor Connector NOTE: If you have a power supply with thermal monitoring, connect its ther- mal sensor cable to JTPWR.
24 ASUS P2V User’ s Manual III. HARDW ARE SETUP Expansion Cards III. H/W SETUP 4. Expansion Cards Expansion Card Installation Procedure 1. Read the documentation for your expansion card and make any necessary hard- ware or software settings for your expansion card, such as jumpers. 2. Remove your computer system’ s cover and the bracket plate on the slot you intend to use. Keep the bracket for possible future use. 3. Carefully align the card’ s connectors and press firmly . 4. Secure the card on the slot with the screw you removed above. 5. Replace the computer system’ s cover . 6. Set up the BIOS if necessary (such as IRQ xx Used By ISA: Y es in PNP AND PCI SETUP) 7. Install the necessary software drivers for your expansion card. Assigning IRQs for Expansion Cards Some expansion cards need to use an IRQ to operate. Generally , an IRQ must be exclusively assigned to one use. In a standard design, there are 16 IRQs available but most of them are already in use, leaving 6 IRQs free for expansion cards. If your motherboard has PCI audio onboard, an extra IRQ will be used, leaving 5 IRQs free. If your motherboard has ISA audio onboard, an extra 3 IRQs will be used, leaving 3 IRQs free. Both ISA and PCI expansion cards may require to use IRQs. System IRQs are avail- able to cards installed in the ISA expansion bus first, then any remaining IRQs are available to PCI cards. Currently , there are two types of ISA cards. The original ISA expansion card design, now referred to as legacy ISA cards, requires that you con- figure the card’ s jumpers manually and then install it in any available slot on the ISA bus. If you use W indows 98, selecting the Interrupt request (IRQ) button in Pr op- erties under Device Manager displays the resource settings being used by a par - ticular device. In W indows 95, the Resources tab under Device Manager displays these settings. (T o gain access to Device Manager in either W indows 98/95, double- click the System icon under the Control Panel program.) Ensure that no two de- vices share the same IRQs or your computer will experience problems when those two devices are in use at the same time. W ARNING! Unplug your power supply when adding or removing expansion cards or other system components. Failure to do so may cause severe damage to both your motherboard and expansion cards.
ASUS P2V User’ s Manual 25 III. INST ALLA TION T o simplify this process, this motherboard complies with the Plug and Play (PnP specification, which was developed to allow automatic system configuration when- ever a PnP-compliant card is added to the system. For PnP cards, IRQs are assigned automatically from those available. If the system has both legacy and PnP ISA cards installed, IRQs are assigned to PnP cards from those not used by legacy cards. The PCI and PNP configuration section of the BIOS setup utility can be used to assign which IRQs are being used by legacy cards. For older legacy cards that do not work with the BIOS, you may contact your vendor for an ISA Configuration Utility . An IRQ number is automatically assigned to PCI expansion cards after those used by legacy and PnP ISA cards. In the PCI bus design, the BIOS automatically assigns an IRQ to a PCI slot that contains a card requiring an IRQ. T o install a PCI card, you need to set the INT (interrupt assignment). Since all the PCI slots on this mother - board use an INT A #, set the jumpers on your PCI cards to INT A. Assigning DMA Channels for ISA Cards Some ISA cards, both legacy and PnP , may also need to use a DMA (Direct Memory Access channel. DMA assignments for this motherboard are handled the same way as the IRQ assignment process described earlier . Y ou can select a DMA channel in the PCI and PnP configuration section of the BIOS Setup utility . IMPOR T ANT : T o avoid conflicts, reserve the necessary IRQs and DMAs for legacy ISA cards (under PNP AND PCI SETUP of the BIOS SOFTW ARE, choose Ye s in IRQ xx Used By ISA and DMA x Used By ISA for those IRQs and DMAs you want to reserve . ISA Cards and Hardware Monitor The onboard hardware monitor uses the address 290H-297H so legacy ISA cards must not use this address or else conflicts will occur . DMA Channels III. INST ALLA TION Accelerated Graphics Port This motherboard provides an accelerated graphics port (AGP) slot to support a new generation of graphics cards with ultra-high memory bandwidth, such as an ASUS 3D Hardware Accelerator . P2V Accelerated Graphics Port (AGP) R
26 ASUS P2V User’ s Manual 5. External Connectors IMPOR T ANT : Ribbon cables should always be connected with the red stripe to Pin 1 on the connectors. Pin 1 is usually on the side closest to the power connector on hard drives and CD-ROM drives, but may be on the opposite side on floppy disk drives. Check the connectors before installation because there may be exceptions. IDE ribbon cables must be less than 46 cm (18 in.), with the second drive connector no more than 15 cm (6 in.) from the first connector . 1. PS/2 Keyboard Connector (6-pin Female) This connection is for a standard keyboard using an PS/2 plug (mini DIN). This connector will not allow standard A T size (large DIN) keyboard plugs. Y ou may use a DIN to mini DIN adapter on standard A T keyboards. PS/2 Keyboard (6-pin Female) 2. PS/2 Mouse Connector (6-pin Female) The system will direct IRQ12 to the PS/2 mouse if one is detected. If not de- tected, expansion cards can use IRQ12. See “PS/2 Mouse Control” in BIOS Features Setup of the BIOS SOFTW ARE. PS/2 Mouse (6-pin Female) W ARNING! Some pins are used for connectors or power sources. These are clearly distinguished from jumpers in the motherboard layout. Placing jumper caps over these connectors will cause damage to your motherboard. Connectors III. INST ALLA TION III. INST ALLA TION
ASUS P2V User’ s Manual 27 III. INST ALLA TION DMA Channels III. INST ALLA TION Connectors III. INST ALLA TION 3. Parallel Port Connector (25-pin Female) Y ou can enable the parallel port and choose the IRQ through “Onboard Parallel Port” in Chipset Features Setup of the BIOS SOFTW ARE. NOTE: Serial print- ers must be connected to the serial port. Parallel (Printer) Port (25-pin Female) 4. Serial Port COM1 and COM2 Connectors (T wo 9-pin Male) The two serial ports can be used for pointing devices or other serial devices. See “Onboard Serial Port” in Chipset Features Setup of the BIOS SOFTW ARE. COM 1 COM 2 Serial Ports (9-pin Male) 5. Floppy Disk Drive Connector (34-1pin FLOPPY) This connector supports the provided floppy disk drive ribbon cable. After con- necting the single end to the board, connect the two plugs on the other end to the floppy drives. (Pin 5 is removed to pr event inserting in the wrong orienta- tion when using ribbon cables with pin 5 plugged). P2V Floppy Disk Drive Connector NOTE: Orient the red stripe to Pin 1 R Floppy Drive Connector Pin 1
28 ASUS P2V User’ s Manual Connectors III. INST ALLA TION III. INST ALLA TION 6. Universal Serial BUS Ports 1 & 2 (T wo 4-pin Female) T wo USB ports are available for connecting USB devices. Universal Serial Bus (USB) 2 USB 1 7. Primary / Secondary IDE Connectors (T wo 40-1pin IDE) These connectors support the provided IDE hard disk ribbon cable. After connect- ing the single end to the board, connect the two plugs at the other end to your hard disk(s). If you install two hard disks, you must configure the second drive to Slave mode by setting its jumper accordingly . Refer to the documentation of your hard disk for the jumper settings. BIOS now supports SCSI device or IDE CD-ROM bootup (see “HDD Sequence SCSI/IDE First” & “Boot Sequence” in the BIOS Featur es Setup of the BIOS SOFTW ARE) (Pin 20 is r emoved to prevent in- serting in the wr ong orientation when using ribbon cables with pin 20 plugged). TIP: Y ou may configure two hard disks to be both Masters using one ribbon cable on the primary IDE connector and another ribbon cable on the secondary IDE connector . Y ou may install one operating system on an IDE drive and an- other on a SCSI drive and select the boot disk through BIOS Features Setup. P2V IDE Connectors Primary IDE Connector PIN 1 Secondary IDE Connector NOTE: Orient the red stripe to PIN 1 R 8. IDE Device Activity LED (2-pin IDELED) This connector supplies power to the cabinet’ s IDE device activity LED. Read and write activity by devices connected to the Primary or Secondary IDE con- nectors will cause the LED to light up. P2V IDE Activity LED TIP: If the case-mounted LED does not light, try reversing the 2-pin plug. IDELED R
ASUS P2V User’ s Manual 29 III. INST ALLA TION Connectors III. INST ALLA TION 9. Chassis / CPU / Power Supply Fan Connectors ( 3-pin F AN) These connectors support cooling fans of 500mA (6W) or less. Orientate the fans so that the heatsink fins allow airflow to go across the onboard heatsink(s) instead of the expansion slots. Depending on the fan manufacturer , the wiring and plug may be dif ferent. The red wire should be positive, while the black should be ground. Connect the fan’ s plug to the board taking into consideration the polarity of the this connector . NOTE: The “Rotation” signal is to be used only by a specially designed fan with rotation signal. The Rotations per Minute (RPM) can be monitored using ASUS PC Probe Utility or Intel LDCM Utility . W ARNING! The CPU and/or motherboard will overheat if there is no airflow across the CPU and onboard heatsinks. Damage may occur to the motherboard and/or the CPU fan if these pins are incorrectly used. These are not jumpers, do not place jumper caps over these pins. P2V 12V olt Cooling Fan Power Chassis Fan Power CPU Fan Power Power Supply Fan GND Rotation 12V R 10. Chassis Intrusion Alarm Lead (4-1 pin CHASIS) This requires an external detection mechanism such as a chassis intrusion moni- tor/sensor or microswitch. The sensor is triggered when a high level signal is sent to the CHASIS lead. This occurs when the side panel is opened or drive bay doors are opened. NOTE: When the chassis is opened, connect/short the Chassis Signal pin to the 5VSB pin. When the chassis is opened, connect/short the Chassis Signal pin to the Ground pin. R P2V Chassis Intrusion Alarm Lead Ground Chassis Signal 5VSB
30 ASUS P2V User’ s Manual III. INST ALLA TION Connectors III. INST ALLA TION 1 1. IrDA-Compliant Infrared Module Connector (5-pin IR) This connector supports the optional wireless transmitting and receiving infrared module. This module mounts to a small opening on system cases that support this feature. Y ou must also configure the setting through “UAR T2 Use Infrared” in Chipset Featur es Setup to select whether UAR T2 is directed for use with COM2 or IrDA. Use the five pins as shown on the Back V iew and connect a ribbon cable from the module to the motherboard according to the pin definitions. Front View 5V IRTX IRRX (NC) GND Back View P2V Infrared Module Connector For the infrared feature to be available, you must connect the optional Infrared (IrDA) module to the motherboard 5V IRRX IRTX FIRRX GND R 12. A TX Power Supply Connector (20-pin A TXPWR) This connector connects to an A TX power supply . The plug from the power supply will only insert in one orientation because of the dif ferent hole sizes. Find the proper orientation and push down firmly but gently making sure that the pins are aligned. P2V A TX Power Connector 3.3V olts -12.0V olts Ground Power Supp Ground Ground Ground -5.0 V olts 5.0 V olts 5.0 V olts Power Good 12.0V olts 3.3 V olts 3.3 V olts Ground 5.0 V olts Ground 5.0 V olts Ground 5V Standby R IMPOR T ANT : Make sure that your A TX power supply can supply at least 10mAmp on the 5-volt standby lead (5VSB). Y ou may experience difficulty in powering on your system if your power supply cannot support the load. For W ake on LAN support, your A TX power supply must supply at least 720mA.
ASUS P2V User’ s Manual 31 III. INST ALLA TION Connectors III. INST ALLA TION 13. W ake-on-LAN Connector (3-pin WOL_CON) The WOL_CON connector powers up the system when a wakeup packet or signal is received from the network through the ASUS PCI-L101 LAN card (see section VII. ASUS LAN Card ). IMPOR T ANT : This feature requires that the W AKE On LAN Power Up Control is set to Enabled (see “Power Management Setup” under IV . BIOS SOFTW ARE ) and that your system has an A TX power supply with at least 720mA 5V standby power . IMPORT ANT : Requires an A TX power supply with at least 720mA 5 volt standby power W ake-on-LAN Connector 5 V olt Standby (No Connection) Ground R 14. SMBus Connector (5-1 pin SMB) This connector allows you to connect SMBus devices. SMBus devices commu- nicate by means of the SMBus with an SMBus host and/or other SMBus de- vices. The SMBus or System Management Bus is a specific implementation of an I 2 C bus, which is a multi-master bus, that is, multiple chips can be connected to the same bus and each one can act as a master by initiating data transfer . P2V SMBus Connector R SMBCLK Ground SMBDA T A 5V 1
32 ASUS P2V User’ s Manual III. INST ALLA TION Connectors III. INST ALLA TION 15. Message LED Lead (MSG.LED) This indicates whether a message has been received from a fax/modem. The LED will remain lit when there is no signal and blink when there is data transfer or waiting in the inbox. This function requires ACPI OS and driver support. 16. SMI Suspend Switch Lead (SMI) This allows the user to manually place the system into a suspend mode or “Green” mode where system activity will be instantly decreased to save electricity and expand the life of certain components when the system is not in use. This 2-pin connector (see the figure below) connects to the case-mounted suspend switch. If you do not have a switch for the connector , you may use the “T urbo Switch” since it does not have a function. SMI is activated when it detects a short to open moment and therefore leaving it shorted will not cause any problems. This may require one or two pushes depending on the position of the switch. 17. A TX Power Switch / Soft Power Switch (PWR.SW) The system power is controlled by a momentary switch connected to this lead. Pushing the button once will switch the system between ON and SLEEP . Push- ing the switch while in the ON mode for more than 4 seconds will turn the system of f. The system power LED shows the status of the system’ s power . 18. Reset Switch Lead (RESET) This 2-pin connector connects to the case-mounted reset switch for rebooting your computer without having to turn of f your power switch. This is a preferred method of rebooting to prolong the life of the system’ s power supply . 19. System Power LED (PWR.LED) This 3-pin connector connects the system power LED, which lights when the system is powered on and blinks when it is in sleep mode. 20. Keyboard Lock Switch Lead (KEYLOCK) This 2-pin connector connects to the case-mounted key switch to allow key- board locking. 21. Speaker Connector (SPEAKER) This 4-pin connector connects to the case-mounted speaker . P2V System Panel Connections PLED Ground MLED PWR_SW * Requires an A TX power supply . 5 V KEYLOCK 5V SPKR Keyboard Lock Speaker Connector Power LED Ground 5 V Reset SW SMI Lead Message LED A TX Power Switch* ExtSMI# Ground ResetCon Ground Ground Ground R
ASUS P2V User’ s Manual 33 III. INST ALLA TION Power Connection Procedures 1. After all connections are made, close the system case cover . 2. Be sure that all switches are of f (in some systems, marked with ). 3. Connect the power supply cord into the power supply located on the back of your system case according to your system user ’ s manual. 4. Connect the power cord into a power outlet that is equipped with a sur ge protector . 5. Y ou may then turn on your devices in the following order: a. Y our monitor b. External SCSI devices (starting with the last device on the chain) c . Y our system power . For A TX power supplies, you need to switch on the power supply as well as press the A TX power switch on the front of the case. 6. The power LED on the front panel of the system case will light. For A TX power supplies, the system LED will light when the A TX power switch is pressed. The monitor LED may light up after the system’ s if it complies with “green” stan- dards or if it has a power standby feature. The system will then run power -on tests. While the tests are running, additional messages will appear on the screen. If you do not see anything within 30 seconds from the time you turn on the power , the system may have failed a power-on test. Recheck your jumper set- tings and connections or call your retailer for assistance. 7. During power -on, hold down <Delete> to enter BIOS setup. Follow the instruc- tions in the next section, BIOS SOFTW ARE. * Powering Off your computer: Y ou must first exit or shut down your operating system before switching of f the power switch. For A TX power supplies, you can press the A TX power switch after exiting or shutting down your operating system. If you use W indows 95, click the Start button, click Shut Down, and then click Shut down the computer?. The power supply should turn off after W indows shuts down. NOTE: The message “Y ou can now safely turn off your computer” will not appear when shutting down with A TX power supplies. Power Connections III. INST ALLA TION
ASUS P2V User’ s Manual 34 IV . BIOS Flash Memory Writer IV . BIOS SOFTW ARE Flash Memory W riter Utility This motherboard has an onboard SCSI BIOS and boot virus protection and therefore, re- quires a 2Mbit flash ROM. AFLASH.EXE: This is the Flash Memory W riter utility that updates the BIOS by uploading a new BIOS file to the 2Mbit programmable flash ROM chip on the motherboard. T o deter- mine the BIOS version of your motherboard, check the last four numbers of the code dis- played on the upper left-hand corner of your screen during bootup. Larger numbers represent a newer BIOS file. This file works only in DOS mode. NOTE: The following screen displays are provided as examples only and may not reflect the screen contents displayed on your system. Main Menu 1. Save Current BIOS T o File This option allows you to save a copy of the original motherboard BIOS in case you need to reinstall it. It is recommended that you save AFLASH.EXE and the BIOS file to a bootable floppy disk. T o save your current BIOS, type [1] at the Main Menu and then press <Enter>. The Save Current BIOS T o File screen appears. IMPOR T ANT! If “unknown” is displayed after Flash Memory:, the memory chip is either not programmable or is not supported by the ACPI BIOS and therefore, cannot be programmed by the Flash Memory Writer utility . T ype a filename and the path, for example, A:\P2V and then press <Enter>.
ASUS P2V User’ s Manual 35 IV . BIOS Flash Memory Writer IV . BIOS SOFTW ARE When prompted to confirm the BIOS update, press Y to start the update. 2. Update BIOS Including Boot Block and ESCD This option updates the boot block, the baseboard BIOS, and the ACPI extended system con- figuration data (ESCD) parameter block from a new BIOS file. See the next page for proce- dures on downloading an updated BIOS file. The utility starts to program the new BIOS information into the flash ROM. When the program- ming is finished, Flashed Suc- cessfully will be displayed. T o update your current BIOS, type 2 at the Main Menu and then press <Enter>. The Update BIOS Including Boot Block and ESCD screen appears. T ype the filename of your new BIOS and the path, for example, A: \V A2I1001.A WD , and then press <Enter>. Follow the onscreen instructions to continue.
ASUS P2V User’ s Manual 36 IV. BIOS Updating BIOS IV . BIOS SOFTW ARE Managing and Updating Y our Motherboard’s BIOS Upon First Use of the Computer System 1. Create a bootable system floppy disk by typing [FORMA T A:/S] from the DOS prompt without creating “AUT OEXEC.BA T” and “CONFIG.SYS” files. 2. Copy AFLASH.EXE to the just created boot disk. 3. Run AFLASH.EXE from this new disk and select option 1. Save Curr ent BIOS to File . See 1. Save Curr ent BIOS T o File on the previous page for more de- tails and the rest of the steps. Updating BIOS Procedur es (only when necessary) 1. Download an updated ASUS BIOS file from the Internet (WWW or FTP) or a BBS (Bulletin Board Service) (see ASUS CONT ACT INFORMA TION on page 3 for details) and save to the disk you created earlier . 2. Boot from the disk you created earlier . 3. At the “A:\” prompt, type AFLASH and then press <Enter>. 4. At the Main Menu, type 2 and then press <Enter>. See 2. Update BIOS In- cluding Boot Block and ESCD on the previous page for more details and the rest of the steps. W ARNING! If you encounter problems while updating the new BIOS, DO NOT turn off your system since this might prevent your system from booting up. Just repeat the process, and if the problem still persists, update the original BIOS file you saved to disk above. If the Flash Memory W riter utility was not able to successfully update a complete BIOS file, your system may not be able to boot up. If this happens, your system will need service.
ASUS P2V User’ s Manual 37 IV . BIOS SOFTW ARE 6. BIOS Setup IV . BIOS BIOS Setup The motherboard supports 5-V olt programmable Flash ROM chip. This memory chip can be updated when BIOS upgrades are released. Use the Flash Memory W riter utility to download the new BIOS file into the ROM chip as described in detail in this section. All computer motherboards provide a Setup utility program for specifying the sys- tem configuration and settings. If your motherboard came in a computer system, the proper configuration entries may have already been made. If so, invoke the Setup utility , as described later , and take note of the configuration settings for future refer- ence; in particular , the hard disk specifications. If you are installing the motherboard, reconfiguring your system or you receive a Run Setup message, you will need to enter new setup information. This section describes how to configure your system using this utility . The BIOS ROM of the system stores the Setup utility . When you turn on the com- puter , the system provides you with the opportunity to run this program. This ap- pears during the Power -On Self T est (POST). Press <Delete> to call up the Setup utility . If you are a little bit late pressing the mentioned key(s), POST will continue with its test routines, thus preventing you from calling up Setup. If you still need to call Setup, reset the system by pressing <Ctrl> <Alt> <Delete>, or by pressing the Reset button on the system case. Y ou can also restart by turning the system off and then back on again. But do so only if the first two methods fail. When you invoke Setup, the CMOS SETUP UTILITY main program screen will appear with the following options:
ASUS P2V User’ s Manual 38 IV . BIOS SOFTW ARE IV . BIOS Standard CMOS Load Defaults The “Load BIOS Defaults” option loads the minimum settings for troubleshooting. “ Load Setup Defaults ”, on the other hand, is for loading optimized defaults for regular use. Choosing defaults at this level, will modify all applicable settings. A section at the bottom of the above screen displays the control keys for this screen. T ake note of these keys and their respective uses. Another section just below the control keys section displays information on the currently highlighted item in the list. Standard CMOS Setup This “Standard CMOS Setup” option allows you to record some basic system hard- ware configuration and set the system clock and error handling. If the motherboard is already installed in a working system, you will not need to select this option anymore. However , if the configuration stored in the CMOS memory on the board gets lost or damaged, or if you change your system hardware configuration, you will need to respecify the configuration values. The configuration values usually get lost or corrupted when the power of the onboard CMOS battery weakens. The preceding screen provides you with a list of options. At the bottom of this screen are the control keys for this screen. T ake note of these keys and their respective uses. User -configurable fields appear in a dif ferent color . If you need information on the selected field, press <F1>. The help menu will then appear to provide you with the information you need. The memory display at the lower right-hand side of the screen is read-only and automatically adjusts accordingly . Details of Standard CMOS Setup: Date T o set the date, highlight the “Date” field and then press either <Page Up>/<Page Down> or < >/<–> to set the current date. Follow the month, day and year format. V alid values for month, day and year are: Month: (1 to 12), Day: (1 to 31), Y ear: ( up to 2079)
ASUS P2V User’ s Manual 39 IV . BIOS SOFTW ARE IV . BIOS Standard CMOS Ti m e T o set the time, highlight the “T ime” field and then press either <Page Up>/<Page Down> or < >/<–> to set the current time. Follow the hour , minute and second format. V alid values for hour , minute and second are: (Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59) . Press <Enter> twice if you do not want to modify the current time. NOTE: Y ou can bypass the date and time prompts by creating an AUTOEXEC.BA T file. For information on how to create this file, please refer to the MS-DOS manual. Hard Disks This field records the specifications for all non-SCSI hard disk drives installed in your system. The onboard PCI IDE connectors provide Primary and Secondary channels for connecting up to four IDE hard disks or other IDE devices. Each chan- nel can support up to two hard disks; the first of which is the “master” and the second is the “slave”. Specifications for SCSI hard disks need not to be entered here since they operate using device drivers and are not supported by any the BIOS. If you install either the optional PCI-SC200 or PCI-SC860 SCSI controller card into the motherboard, see section VI for instructions. If you install other vendor ’ s SCSI controller card, refer to their respective documentations on how to install the required SCSI drivers. For IDE hard disk drive setup, you can: • Use the Auto setting for detection during bootup. • Use the IDE HDD AUTO DETECTION in the main menu to automatically enter the drive specifications. • Enter the specifications yourself manually by using the “User” option. The entries for specifying the hard disk type include CYLS (number of cylinders), HEAD (number of read/write heads), PRECOMP (write precompensation), LANDZ (landing zone), SECT OR (number of sectors) and MODE . The SIZE field auto- matically adjusts according to the configuration you specify . The documentation that comes with your hard disk should provide you with the information regarding the drive specifications. The MODE entry is for IDE hard disks only , and can be ignored for MFM and ESDI drives. This entry provides three options: Normal, Lar ge, LBA , or Auto (see below). Set MODE to the Normal for IDE hard disk drives smaller than 528MB; set it to LBA for drives over 528MB that support Logical Block Addressing (LBA) to allow larger IDE hard disks; set it to Lar ge for drives over 528MB that do not support LBA. Lar ge type of drive can only be used with MS-DOS and is very uncommon. Most IDE drives over 528MB support the LBA mode.
ASUS P2V User’ s Manual 40 IV . BIOS SOFTW ARE IV . BIOS Standard CMOS Auto detection of hard disks on bootup For each field: Primary Master , Primary Slave, Secondary Master , and Secondary Slave, you can select Auto under the TYPE and MODE fields. This will enable auto detection of your IDE hard disk during bootup. This will allow you to change your hard disks (with the power off) and then power on without having to reconfigure your hard disk type. If you use older hard disks that do not support this feature, then you must configure the hard disk in the standard method as described earlier by the “User” option. NOTE: After the IDE hard disk drive information has been entered into BIOS, new IDE hard disk drives must be partitioned (such as with FDISK) and then formatted before data can be read from and write on. Primary IDE hard disk drives must have its partition set to active (also possible with FDISK). NOTE: SETUP Defaults are noted in parenthesis next to each function heading. Drive A / Drive B These fields record the types of floppy disk drives installed in your system. The available options for drives A and B are: 360KB, 5.25 in.; 1.2MB, 5.25 in.; 720KB, 3.5 in.; 1.44MB, 3.5 in.; 2.88MB, 3.5 in.; None T o enter the configuration value for a particular drive, highlight its corresponding field and then select the drive type using the left- or right-arrow keys. Floppy 3 Mode Support This is the Japanese standard floppy drive. The standard stores 1.2MB in a 3.5inch diskette. This is normally disabled but you may choose from either: Drive A, Drive B, Both, and Disabled V ideo Set this field to the type of video display card installed in your system. The options are EGA/VGA , CGA 49, CGA 80 , and Mono (for Hercules or MDA) . If you are using a VGA or any higher resolution card, choose EGA/VGA . Halt On This field determines which types of errors will cause the system to halt. Choose from All Err ors ; No Err ors ; All ,But Keyboar d, All ,But Diskette ; and All,But Disk/Key .
ASUS P2V User’ s Manual 41 IV . BIOS SOFTW ARE IV . BIOS BIOS Features BIOS Features Setup This “BIOS Features Setup” option consists of configuration entries that allow you to improve your system performance, or let you set up some system features accord- ing to your preference. Some entries are required by the motherboard’ s design to remain in their default settings. A section at the lower right of the screen displays the control keys you can use. T ake note of these keys and their respective uses. If you need information on a particular entry , highlight it and then press <F1>. A pop-up help menu will appear to provide you with the information you need. <F5> loads the last set values, <F6> and <F7> loads the BIOS default values and Setup default values, respectively . NOTE: SETUP Defaults are noted in parenthesis next to each function heading. Details of BIOS Features Setup Boot V irus Detection (Enabled) This field allows you to set boot virus detection, ensuring a virus-free boot sector . This new antivirus solution is unlike native BIOS tools, which of fer limited virus protection typically by write-protecting the partition table. W ith this new solution, your computer is protected against boot virus threats earlier in the boot cycle, that is, before they have a chance to load into your system. This ensures your computer boots to a clean operating system. T he system halts and displays a warning message when it detects a virus. If this occurs, you can either allow the operation to continue or use a virus-free bootable floppy disk to restart and investigate your system. Be- cause of conflicts with new operating systems, for example, during installation of new softwares, you may have to set this to Disabled to prevent write errors. CPU Level 1 Cache / CPU Level 2 Cache (Enabled) These fields allow you to choose from the default of Enabled or choose Disabled to turn on or off the CPU’ s Level 1 and Level 2 built-in cache.
ASUS P2V User’ s Manual 42 IV . BIOS SOFTW ARE IV . BIOS BIOS Features CPU Level 2 Cache ECC Check (Disabled) This function controls the ECC check capability in the CPU level 2 cache. BIOS Update (Enabled) This functions as an update loader integrated into the BIOS to supply the processor with the required data. The BIOS will load the update on all processors during system bootup in the default position of Enabled . T urbo Mode (Disabled) Leave on default setting to resolve timing issues. Quick Power On Self T est (Enabled) This field speeds up the Power-On Self T est (POST) routine by skipping memory retesting a second and third time. Setup default setting for this field is Enabled . A complete test of the system is done on each test. HDD Sequence SCSI/IDE First (IDE) When using both SCSI and IDE hard disk drives, IDE is always the boot disk using drive letter C (default setting of IDE). This new feature allows a SCSI hard disk drive to be the boot disk when set to SCSI. This allows multiple operating systems to be used on both IDE and SCSI drives or the primary operating system to boot using a SCSI hard disk drive. Boot Sequence (A,C) This field determines where the system looks first for an operating system. Options are A,C ; A,CDROM,C ; CDROM,C,A ; CDROM,A,C ; D,A ; E,A; F, A ; C only; LS/ZIP , C ; LAN,A,C ; LAN,C,A ; and C,A. The setup default setting is to check first the floppy disk and then the hard disk drive, that is, A, C . Boot Up Floppy Seek (Disabled) When enabled, the BIOS will seek drive A once. Floppy Disk Access Control (R/W) This allows protection of files from the computer system to be copied to floppy disks by allowing the setting of Read Only to only allow reads from the floppy disk drive but not writes. The setup default R/W allows both reads and writes. IDE HDD Block Mode Sectors (HDD MAX) This field enhances hard disk performance by making multi-sector transfers instead of one sector per transfer . Most IDE drives, except older versions, can utilize this feature. Selections are HDD MAX , Disabled , 2, 4, 8, 16 , and 32. HDD S.M.A.R.T . capability (Disabled) This field enables or disables S.M.A.R.T . (Self-Monitoring Analysis and Reporting T echnology) support for S.M.A.R.T .-capable hard disk drives. This technology re- quires an application that can display S.M.A.R.T . warning messages.
ASUS P2V User’ s Manual 43 IV . BIOS SOFTW ARE IV . BIOS BIOS Features PS/2 Mouse Function Contr ol (Auto) The default of Auto allows the system to detect a PS/2 mouse on bootup. If detected, IRQ12 will be used for the PS/2 mouse. IRQ12 will be reserved for expansion cards if a PS/2 mouse is not detected. Enabled will always reserve IRQ12, whether on bootup a PS/2 mouse is detected or not. OS/2 Onboard Memory > 64M (Disabled) When using OS/2 operating systems with installed DRAM of greater than 64MB, you need to set this option to Enabled otherwise leave this on Disabled . ...................................................................................................................................... PCI/VGA Palette Snoop (Disabled) Some display cards that are nonstandard VGA such as graphics accelerators or MPEG V ideo Cards may not show colors properly . The setting Enabled should correct this problem. Otherwise leave this on the setup default setting of Disabled . V ideo ROM BIOS Shadow (Enabled) This field allows you to change the video BIOS location from ROM to RAM. Relocat- ing to RAM enhances system performance, as information access is faster than the ROM. C8000-CBFFF to DC000-DFFFF (Disabled) These fields are used for shadowing other expansion card ROMs. If you install other expansion cards with ROMs on them, you will need to know which addresses the ROMs use to shadow them specifically . Shadowing a ROM reduces the memory available between 640K and 1024K by the amount used for this purpose. Boot Up NumLock Status (On) This field enables users to activate the Number Lock function upon system boot. T ypematic Rate Setting (Disabled) When enabled, you can set the two typematic controls listed next. Setup default setting is Disabled . T ypematic Rate (Chars/Sec) (6) This field controls the speed at which the system registers repeated keystrokes. Options range from 6 to 30 characters per second. Setup default setting is 6; other settings are 8 , 10 , 12 , 15 , 20 , 24 , and 30. T ypematic Delay (Msec) (250) This field sets the time interval for displaying the first and second characters. Four delay rate options are available: 250, 500 , 750, and 1000 . Security Option (System) When you specify a Supervisor Passwor d and/or User Passwor d (explained later in this section), the Security Option field determines when the system prompts for the password. The default setting is System , where the system prompts for the User Password every time you start your system. The other option is Setup , where the system goes through its startup routine unless the Setup utility is called, when the system prompts for the Supervisor Password.
ASUS P2V User’ s Manual 44 IV . BIOS SOFTW ARE IV . BIOS Chipset Features Chipset Features Setup This “Chipset Features Setup” option controls the configuration of the board’ s chipset. Control keys for this screen are the same as for the previous screen. NOTE: SETUP Defaults are noted in parenthesis next to each function heading. Details of Chipset Features Setup SDRAM Configuration (By SPD) This sets the optimal timing for items 2-4. Leave on default setting, depending on the memory modules that you are using. Default setting is By SPD, which config- ures items 2-4 by reading the contents in the SPD (Serial Presence Detect) device. This 8-pin serial EEPROM device stores critical parameter information about the module, such as memory type, size, speed, voltage interface, and module banks. SDRAM CAS Latency This controls the latency between SDRAM read command and the time that the data actually becomes available. Leave on default setting. SDRAM RAS Precharge Time This controls the idle clocks after issuing a prechar ge command to SDRAM. Leave on default setting. SDRAM RAS to CAS Delay This controls the latency between SDRAM active command and the read/write command. Leave on default setting. Read Around W rite (Disabled) Leave on default setting for SDRAM compatibility . CPU-DRAM Back-Back T rans. (Disabled) Leave on default setting for compatibility and reliability . Delayed T ransaction (Enabled) If Enabled , this frees the PCI Bus during CPU accessing of 8-bit ISA cards that normally consume about 50–60 PCI clocks without PCI delayed transaction. If PCI bus masters cannot use the PCI bus, leave this on the default setting of Disabled for some PCI cards that are not PCI 2.1 compliant.
ASUS P2V User’ s Manual 45 IV . BIOS SOFTW ARE IV . BIOS Chipset Features PCI to DRAM Prefetch (Disabled) Leave on default setting for best stability . Byte Merge (Disabled) Leave on default setting for compatibility . Set to Enabled for increased performance in some PCI VGA cards. DRAM Read Latch Delay (1.0 ns) This controls the timing point for latching SDRAM data. Leave on default setting. MD to HD Delay (Auto) This controls the pipe stage for SDRAM data MD to host side data bus HD. Leave on default setting. DRAM Operating Fr equency (Auto) This controls the DRAM’ s operating frequency as that ( FSB) or 2/3 ( 2/3 FSB) of the host side frequency . Leave on default setting. AGP Capability (2X Mode) Leave on default setting for best performance. Set to 1X Mode for compatibility . Graphics Aperture Size (64MB) Memory-mapped, graphics data structures can reside in a Graphics Aperture. Leave on default setting. V ideo Memory Cache Mode (UC) USWC (uncacheable, speculative write combining) is a new cache technology for the video memory of the processor . It can greatly improve the display speed by caching the display data. Y ou must leave this on the default setting of UC (uncacheable) if your display card cannot support this feature or else your system may not boot. Memory Hole At 15M–16M (Disabled) Enabling this feature reserves 15MB to 16MB memory address space to ISA expan- sion cards that specifically require this setting. This makes the memory from 15MB and up unavailable to the system. Expansion cards can only access memory up to 16MB. This is Disabled by default. DRAM are xx bits wide If all your DRAM modules have ECC chips (e.g., 8 chips 1 ECC chips), they are considered 72bits and the corresponding screen (left) will be shown. On the other hand, if your DRAM modules do not have ECC chips (e.g. 8 chips), they are consid- ered 64 bits and the corresponding screen (right) will be shown. Data Integrity Mode (Non-ECC) Non-ECC has byte-wise write capability but no provision for protecting data integ- rity in the DRAM array . EC-Only data errors are detected but not corrected. ECC allows detection of single-bit and multiple-bit errors and recovery of single-bit er - rors. (See section III for more information on DRAM memory modules.) ....................................................................................................................................
ASUS P2V User’ s Manual 46 IV . BIOS SOFTW ARE Onboard FDC Controller (Enabled) When Enabled , this field allows you to connect your floppy disk drives to the onboard floppy disk drive connector instead of a separate controller card. If you want to use a different controller card to connect the floppy disk drives, set this field to Disabled . Onboard FDC Swap A & B (No Swap) This field allows you to reverse the hardware drive letter assignments of your floppy disk drives. T wo options are available: No Swap and Swap AB. If you want to switch drive letter assignments through the onboard chipset, set this field to Swap AB . Onboard Serial Port 1 (3F8H/IRQ4) Settings are 3F8H/IRQ4, 2F8H/IRQ3, 3E8H/IRQ4, 2E8H/IRQ10, and Disabled. Onboard Serial Port 2 (2F8H/IRQ3) Settings are 3F8H/IRQ4, 2F8H/IRQ3, 3E8H/IRQ4, 2E8H/IRQ10, and Disabled. Onboard Parallel Port (378H/IRQ7) This field sets the address of the onboard parallel port connector . Y ou can select either: 3BCH / IRQ 7, 378H / IRQ 7, 278H / IRQ 5, Disabled. If you install an I/O card with a parallel port, ensure that there is no conflict in the address assignments. The PC can support up to three parallel ports as long as there are no conflicts for each port. Parallel Port Mode (ECP EPP) This field allows you to set the operation mode of the parallel port. The setting Normal , allows normal-speed operation but in one direction only; EPP allows bidi- rectional parallel port operation at maximum speed; ECP allows the parallel port to operate in bidirectional mode and at a speed faster than the maximum data transfer rate; ECP EPP allows normal speed operation in a two-way mode. ECP DMA Select (3) This selection is available only if you select ECP or ECP EPP in the Parallel Port Mode . Select either DMA Channel 1, 3, or Disable . UAR T2 Use Infrared (Disabled) When enabled, this field activates the onboard infrared feature and sets the second serial UAR T to support the infrared module connector on the motherboard. If your system already has a second serial port connected to the onboard COM2 connector , it will no longer work if you enable the infrared feature. By default, this field is set to Disabled , which leaves the second serial port UAR T to support the COM2 serial port connector . See IrDA-compliant infrared module connector under section III . Onboard PCI IDE Enable (Both) Y ou can select to enable the primary IDE channel, secondary IDE channel, both, or disable both channels (for systems with only SCSI drives). IDE Ultra DMA Mode (Auto) This field autodetects Ultra DMA capability (for improved transfer speeds and data in- tegrity) for compatible IDE devices. Set to Disable to suppress Ultra DMA capability . IDE 0 Master/Slave PIO/DMA Mode, IDE 1 Master/Slave PIO/DMA Mode (Auto) Each channel (0 and 1) has both a master and a slave making four IDE devices possible. Because each IDE device may have a dif ferent Mode timing ( 0, 1, 2, 3, 4), it is necessary for these to be independent. The default setting of Auto will allow autodetection to ensure optimal performance IV . BIOS Chipset Features
ASUS P2V User’ s Manual 47 IV . BIOS SOFTW ARE IV . BIOS Power Management Power Management Setup This “Power Management Setup” option allows you to reduce power consumption. This feature turns off the video display and shuts down the hard disk after a period of inactivity . NOTE: SETUP Defaults are noted in parenthesis next to each function heading. Details of Power Management Setup Power Management (User Define) This field acts as the master control for the power management modes. Max Saving puts the system into power saving mode after a brief period of system inactivity; Min Saving is almost the same as Max Saving except that this time the system inac- tivity period is longer; Disable disables the power saving features; User Define al- lows you to set power saving options according to your preference. IMPOR T ANT : Advanced Power Management (APM) should be installed to keep the system time updated when the computer enters suspend mode activated by the BIOS Power Management. For DOS environments, you need to add the statement, DEVICE=C:\DOS\POWER.EXE, in you CONFIG.SYS. For W indows 3.x and W in- dows 95, you need to install W indows with the APM feature. A battery and power cord icon labeled “Power” will appear in the “Control Panel.” Choose “Advanced” in the Power Management Field. V ideo Off Option (Suspend -> Off ) This field determines when to activate the video of f feature for monitor power manage- ment. The settings are Suspend -> Off and Always On.
ASUS P2V User’ s Manual 48 IV . BIOS SOFTW ARE IV . BIOS Power Management V ideo Off Method (DPMS OFF) This field defines the video off features. The following options are available: DPMS OFF , DPMS Reduce ON , Blank Screen , V/H SYNC Blank, DPMS Standby , and DPMS Suspend . The DPMS (Display Power Management System) features allow the BIOS to control the video display card if it supports the DPMS feature. Blank Scr een only blanks the screen (use this for monitors without power management or “green” features. If set up in your system, your screen saver will not display with Blank Scr een selected). V/H SYNC Blank blanks the screen and turns of f vertical and horizontal scanning. ....................................................................................................................................... PM T imers This section controls the time-out settings for the Power Management scheme. The fields included in this section are “HDD Power Down”, which places the hard disk into its lowest power consumption mode, and the Doze, Standby and Suspend sys- tem inactivation modes. The system automatically “wakes up” from any power saving mode when there is system activity such as when a key is pressed from the keyboard, or when there is activity detected from the enabled IRQ channels. HDD Power Down (Disable) Shuts down any IDE hard disk drives in the system after a period of inactivity . This time period is user-configurable to 1–15 Min or Disable. This feature does not affect SCSI hard drives. Suspend Mode (Disable) Sets the period of time after which the suspend mode activates: 30 sec, 1 Min, 2 Min , 4 Min , 8 Min , 20 Min , 30 Min , 40 Min , 1 Hour , and Disable . ....................................................................................................................................... Power Up Control This section determines the ways the system can be controlled when it is started or restarted, when modem activity is detected, or when power to the computer is inter - rupted and reapplied. The Soft-Of f mode refers to powering of f the system through a momentary button switch (A TX switch) or through the software as opposed to disconnecting the AC power by way of a rocker switch or other means. PWR Button < 4 Secs (Soft Off) When set to Soft Off, the A TX switch can be used as a normal system power-of f button when pressed for less than 4 seconds. Suspend allows the button to have a dual function where pressing less than 4 seconds will place the system in sleep mode. No Function disables the A TX switch function when the button is pressed under 4 seconds. Regardless of the setting, holding the A TX switch for more than 4 seconds will power off the system.
ASUS P2V User’ s Manual 49 IV . BIOS SOFTW ARE IV . BIOS Power Management PWR Up On Modem Act (Enabled) This allows either settings of Enabled or Disabled for powering up the computer (turns the A TX power supply on) when the modem receives a call while the computer is Soft Off . NOTE: The computer cannot receive or transmit data until the computer and appli- cations are fully running, thus connection cannot be made on the first try . T urning an external modem of f and then back on while the computer is off causes an initializa- tion string that will also cause the system to power on. AC PWR Loss Restart (Disabled) This allows you to set whether you want your system to boot up after the power has been interrupted. Disabled leaves your system of f after reapplying power and En- abled boots up your system after reapplying power . W ake On LAN (Enabled) This allows you to remotely power up your system through your network by send- ing a wake-up frame or signal. W ith this feature, you can remotely upload/download data to/from systems during of f-peak hours. Set to Enabled to set this feature. IMPOR T ANT : This feature requires the ASUS PCI-L101 LAN Card (see VII. ASUS LAN Card ) and an A TX power supply with at least 720mA 5V standby power . Automatic Power Up (Disabled) This allows you to have an unattended or automatic power up of your system. Y ou may configure your system to power up at a certain time of the day by selecting Everyday , which will allow you to set the time or at a certain time and day by selecting By Date. ..................................................................................................................................... Fan Monitor (xxxxRPM) The onboard hardware monitor is able to detect the Chassis Fan Speed, CPU Fan Speed, and the Power Supply Fan Speed in Rotations Per Minute (RPM). These values refresh upon any key entries in the BIOS setup screen. Set to Ignor e if one of these are not used so that error messages will not be given. ..................................................................................................................................... Thermal Monitor (xxxC/xxxF) The onboard hardware monitor is able to detect the CPU and MB (motherboard) tem- peratures. These values refresh upon key entries. Set to Ignor e only if necessary . ..................................................................................................................................... V oltage Monitor (xx.xV) The onboard hardware monitor is able to detect the voltages put out by the voltage regulators. These values refresh upon key entries. Set to Ignor e only if necessary . NOTE: If any of the monitored items are out of range, an error message will appear: “Hardware Monitor found an error , enter POWER MANAGEMENT SETUP for details”. Y ou will then be prompted to “Press F1 to continue, DEL to enter SETUP”.
ASUS P2V User’ s Manual 50 IV . BIOS SOFTW ARE Plug & Play / PCI IV. BIOS PNP and PCI Setup This “PNP and PCI Setup” option configures the PCI bus slots. All PCI bus slots on the system use INT A#, thus all installed PCI cards must be set to this value. NOTE: SETUP Defaults are noted in parenthesis next to each function heading. Details of PNP and PCI Setup PNP OS Installed (No) This field allows you to use a Plug-and-Play (PnP) operating system to configure the PCI bus slots instead of using the BIOS. Thus interrupts may be reassigned by the OS when Ye s is selected. When a non-PnP OS is installed or to prevent reassign- ing of interrupt settings, select the default setting of No . Slot 1 IRQ to Slot 4 IRQ (Auto) Thes e fields set how IRQ use is determined for each PCI slot. The default setting for each field is Auto, which uses auto-routing to determine IRQ use. The other options are manual settings of NA, 3 , 4 , 5 , 7 , 9 , 10, 11 , 12, 14 or 15 for each slot. PCI Latency T imer (32 PCI Clock) The default setting of 32 PCI Clock enables maximum PCI performance for this motherboard. IRQ xx Used By ISA (No/ICU) These fields indicate whether or not the displayed IRQ for each field is being used by a legacy (non-PnP) ISA card. T wo options are available: No/ICU and Ye s . The first option, the default value, indicates either that the displayed IRQ is not used or an ISA Configuration Utility (ICU) is being used to determine if an ISA card is using that IRQ. If you install a legacy ISA card that requires a unique IRQ, and you are not using an ICU, you must set the field for that IRQ to Ye s . For example: If you install a legacy ISA card that requires IRQ 10, then set IRQ10 Used By ISA to Ye s . ......................................................................................................................................
ASUS P2V User’ s Manual 51 IV . BIOS SOFTW ARE IV . BIOS Plug & Play / PCI DMA x Used By ISA (No/ICU) These fields indicate whether or not the displayed DMA channel for each field is being used by a legacy (non-PnP) ISA card. A vailable options include: No/ICU and Ye s . The first option, the default setting, indicates either that the displayed DMA channel is not used or an ICU is being used to determine if an ISA card is using that channel. If you install a legacy ISA card that requires a unique DMA channel, and you are not using an ICU, you must set the field for that channel to Ye s . ISA MEM Block BASE (No/ICU) This field allows you to set the base address and block size of a legacy ISA card that uses any memory segment within the C800H and DFFFH address range. If you have such a card, and you are not using an ICU to specify its address range, select a base address from the six available options; the ISA MEM Block SIZE field will then appear for selecting the block size. If you have more than one legacy ISA card in your system that requires to use this address range, you can increase the block size to either 8K, 16K, 32K, or 64K. If you are using an ICU to accomplish this task, leave ISA MEM Block BASE to its default setting of No/ICU . SYMBIOS SCSI BIOS (Auto) Auto allows the motherboard’ s BIOS to detect whether you have a Symbios SCSI card. If a Symbios SCSI card is detected, the motherboard’ s Symbios BIOS will be enabled; if no Symbios SCSI card is detected, the onboard Symbios SCSI BIOS will be disabled. Disabled will disable the motherboard’ s Symbios SCSI BIOS so that the BIOS on an external Symbios SCSI card can be used. (If your Symbios SCSI card does not have a BIOS, the Symbios SCSI card will not function.) USB IRQ (Enabled) Enabled reserves an IRQ# for the USB to work, Disabled does not allow the USB to have an IRQ# and therefore prevents the USB from functioning. If you are not using any USB devices, you may set this feature to Disabled to save an extra IRQ# for expansion cards. VGA BIOS Sequence (PCI/AGP) If your computer has both PCI and AGP VGA cards, this field allows you to select which of the cards will act as your primary card. The default, PCI/AGP , allows your PCI card to take precedent when detected. AGP/PCI uses the AGP card as your primary card.
ASUS P2V User’ s Manual 52 IV . BIOS SOFTW ARE Load Defaults IV. BIOS Load BIOS Defaults This “Load BIOS Defaults” option allows you to load the troubleshooting default values permanently stored in the BIOS ROM. These default settings are non-opti- mal and disable all high performance features. T o load these default settings, high- light “Load BIOS Defaults” on the main screen and then press <Enter>. The system displays a confirmation message on the screen. Press <Y> and then <Enter> to confirm. Press <N> and then <Enter> to abort. This feature does not af fect the fields on the Standard CMOS Setup screen. Load Setup Defaults This “Load Setup Defaults” option allows you to load the default values to the sys- tem configuration fields. These default values are the optimized configuration set- tings for the system. T o load these default values, highlight “Load Setup Defaults” on the main screen and then press <Enter>. The system displays a confirmation message on the screen. Press <Y> and then <Enter> to confirm. Press <N> and then <Enter> to abort. This feature does not affect the fields on the Standard CMOS Setup screen.
ASUS P2V User’ s Manual 53 IV . BIOS SOFTW ARE Supervisor Password and User Password These two options set the system passwords. “Supervisor Password” sets a pass- word that will be used to protect the system and the Setup utility; “User Password” sets a password that will be used exclusively on the system. By default, the system comes without any passwords. T o specify a password, highlight the type you want and then press <Enter>. A password prompt appears on the screen. T aking note that the password is case sensitive, and can be up to 8 alphanumeric characters long, type in your password and then press <Enter>. The system confirms your password by asking you to type it again. After setting a password, the screen automatically re- verts to the main screen. IV . BIOS Passwords Forgot the password? If you for got the password, you can clear the password by erasing the CMOS Real T ime Clock (R TC) RAM. The RAM data containing the password information is powered by the onboard button cell battery . T o erase the R TC RAM: (1) Unplug your computer , (2) Short the solder points, (3) T urn ON your computer , (4) Hold down <Delete> during bootup and enter BIOS setup to re-enter user preferences. Short small solder points to clear CMOS P2V Clear RTC RAM CLRTC R T o implement password protection, specify in the “Security Option” field of the BIOS Features Setup screen when the system will prompt for the password. If you want to disable either password, press <Enter> instead of entering a new password when the “Enter Password” prompt appears. A message confirms the password has been disabled.
ASUS P2V User’ s Manual 54 IV . BIOS SOFTW ARE IV . BIOS Hard Disk Detect IDE HDD Auto Detection This “IDE HDD Auto Detection” option detects the parameters of an IDE hard disk drive, and automatically enters them into the Standard CMOS Setup screen. Up to four IDE drives can be detected, with parameters for each listed inside the box. T o accept the optimal entries, press <Y> or else select from the numbers dis- played under the OPTIONS field (2, 1, 3 in this case); to skip to the next drive, press <N>. If you accept the values, the parameters will appear listed beside the drive letter on the screen. The process then proceeds to the next drive letter . Pressing <N> to skip rather than to accept a set of parameters causes the program to enter zeros after that drive letter . Remember that if you are using another IDE controller that does not feature En- hanced IDE support for four devices, you can only install two IDE hard disk drives. Y our IDE controller must support the Enhanced IDE features in order to use Drive E and Drive F . The onboard PCI IDE controller supports Enhanced IDE, with two connectors for connecting up to four IDE devices. If you want to use another con- troller that supports four drives, you must disable the onboard IDE controller in the Chipset Features Setup screen. When auto-detection is completed, the program automatically enters all entries you accepted on the field for that drive in the Standard CMOS Setup screen. Skipped entries are ignored and are not entered in the screen. If you are auto-detecting a hard disk that supports the LBA mode, three lines will appear in the parameter box. Choose the line that lists LBA for an LBA drive. Do not select Large or Normal. The auto-detection feature can only detect one set of parameters for a particular IDE hard drive. Some IDE drives can use more than one set. This is not a problem if the drive is new and empty .
ASUS P2V User’ s Manual 55 IMPOR T ANT : If your hard disk was already formatted on an older previous system, incorrect parameters may be detected. Y ou will need to enter the correct parameters manually or use low-level format if you do not need the data stored on the hard disk. If the parameters listed dif fer from the ones used when the disk was formatted, the disk will not be readable. If the auto-detected parameters do not match the ones that should be used for your disk, do not accept them. Press <N> to reject the presented settings and enter the correct ones manually from the Standard CMOS Setup screen. Save & Exit Setup Select this option to save into the CMOS memory all modifications you specified during the current session. T o save the configuration changes, highlight the “Save & Exit Setup” option on the main screen, type “Y”, and then press <Enter>. Exit Without Saving Select this option to exit the Setup utility without saving the modifications you specify during the current session. T o exit without saving, highlight the “Exit W ithout Sav- ing” option on the main screen and then press <Enter>. IV . BIOS SOFTW ARE IV . BIOS Save & Exit
ASUS P2V User’ s Manual 56 V . DESKT OP MANAGEMENT Desktop Management Interface (DMI) V . DMI DMI Introduction Introducing the ASUS DMI Configuration Utility This motherboard supports DMI within the BIOS level and provides a DMI Con- figuration Utility to maintain the Management Information Format Database (MIFD). DMI is able to auto-detect and record information pertinent to a computer ’ s system such as the CPU type, CPU speed, and internal/external frequencies, and memory size. The onboard BIOS will detect as many system information as possible and store those collected information in a 4KB block in the motherboard’ s Flash EPROM and allow the DMI to retrieve data from this database. Unlike other BIOS software, the BIOS on this motherboard uses the same technology implemented for Plug and Play to allow dynamic real-time updating of DMI information versus creating a new BIOS image file and requiring the user to update the whole BIOS. This DMI Con- figuration Utility also allows the system integrator or end user to add additional information into the MIFD such as serial numbers, housing configurations, and ven- dor information. Those information not detected by the motherboard BIOS and has to be manually entered through the DMI Configuration Utility and updated into the MIFD. This DMI Configuration Utility provides the same reliability as PnP updat- ing and will prevent the refreshing failures associated with updating the entire BIOS. System Requirements The DMI Configuration Utility (DMICFG2.EXE) must be used in real mode in order for the program to run, the base memory must be at least 180K. Memory managers like HIMEM.SYS (required by windows) must not be installed. Y ou can boot up from a system diskette without AUTOEXEC.BA T and CONFIG.SYS files, “REM” HIMEM.SYS in the CONFIG.SYS, or press <F5> during bootup to bypass your AUTOEXEC.BA T and CONFIG.SYS files.
ASUS P2V User’ s Manual 57 V . DESKT OP MANAGEMENT V . DMI Using DMI Utility Using the ASUS DMI Configuration Utility NOTE: The following screen displays are provided as examples only and may not reflect the screen contents on your system. Edit DMI (or delete) Use the ←→ (left-right) cursors to move the top menu items and the ↑↓ (up-down) cursor to move between the left hand menu items. The bottom of the screen will show the available keys for each screen. Press enter at the menu item to enter the right hand screen for editing. “Edit component” appears on top. The reversed color field is the current cursor position and the blue text are available for editing. The orange text shows auto-detected information and are not available for editing. The blue text “Press [ENTER] for detail” contains a second pop-up menu is available, use the - (plus-minus) keys to change the settings. Enter to exit and save, ESC to exit and not save . If the user has made changes, ESC will prompt you to answer Y or N. Enter Y to go back to the left-hand screen and save, enter N to go back to left-hand screen and not save . If editing has not been made, ESC will send you back to the left hand menu without any messages. Notes A heading, *** BIOS Auto Detect *** , appears on the right for each menu item on the left side that has been auto detected by the system BIOS. A heading, *** User Modified *** , will appear on the right for menu items that have been modified by the user .
ASUS P2V User’ s Manual 58 V . DESKT OP MANAGEMENT Save MIFD Y ou can save the MIFD (normally only saved to flash ROM) to a file by entering the drive and path here. If you want to cancel save, you may press ESC and a message “Bad File Name” appears here to show it was not saved. Load MIFD Y ou can load the disk file to memory by entering a drive and path and file name here. Load BIOS Defaults Y ou can load the BIOS defaults from a MIFD file and can clear all user modified and added data. Y ou must reboot your computer in order for the defaults to be saved back into the Flash BIOS. V . DMI Using DMI Utility
ASUS P2V User’ s Manual 59 VI. ASUS LAN Card Parts / Layout VI. ASUS LAN Card ASUS PCI-L101 Fast Ethernet Card LAN Activity Output Signal RJ45 LEDs Motherboard type Wake on LAN Output Signal ASUS Other Intel Chipset If you are using the ASUS PCI-L101 on an ASUS motherboard, leave the jumper on its defaut setting of “ASUS.” If you are using another brand of motherboard, set the jumper to “Other .” Connect the W ake on LAN (WOL) output signal to the motherboard’ s WOL_CON in order to utilize the wake on LAN feature of the moth- erboard. Connect the LAN activity output signal (LAN_LED) to the system cabinet’ s front panel LAN_LED in order to display the LAN data activity .
60 ASUS P2V User’ s Manual VI. ASUS LAN Card Information VI. ASUS LAN Card Features • Intel 82558 Ethernet LAN Controller (Fully integrated 10BASE-T/100BASE-TX) • W ake-On-LAN Remote Control Function Supported • PCI Bus Master Complies to PCI Local Bus Rev . 2.1 specifications • Consists of MAC & PHY (10/100Mbps) interfaces • Complies to IEEE 802.3 10BASE-T and IEEE 802.3u 100BASE-TX interfaces • Fully supports 10BASE-T & 100BASE-TX operations through a single RJ45 port • Supports 32-bit Bus Master T echnology / PCI Rev . 2.1 • Enhancements on ACPI & APM • Adheres to PCI Bus Power Management Interface Rev . 1.0, ACPI Rev . 1.0, and Device Class Power Management Rev . 1.0 • IEEE 802.3u auto-negotiation for 10Mbps/100Mbps Network Data Transfer Rates. • Provides LED indicators for monitoring network conditions • Plug and Play Software Driver Support • NetW are ODI Drivers - Novell Netware 3.x, 4.x, DOS, OS/2 Client • NDIS 2.01 Drivers - Microsoft LAN Manager , Microsoft W indows 3.1 1, IBM LAN Server • NDIS 3.0 Drivers - Microsoft W indows NT , Microsoft W indows 95, Microsoft W indows 3.1 1 Question and Answer Q: What is W ake-On-LAN ? A: The W ake-On-LAN feature provides the capability to remotely power on sys- tems supporting W ake-On-LAN by simply sending a wake-up frame. W ith this feature, remotely uploading/downloading data to/from systems during of f-peak hours will be feasible. Q: What can W ake-On-LAN do for you ? A: W ake-On-LAN is a remote management tool with advantages that can reduce system management workload, provide flexibility to the system administrator ’ s job, and then of course save you time-consuming ef forts and costs. Q: What components does W ake-On-LAN require to be enable? A: T o enable W ake-On-LAN function, your system requires Ethernet LAN adapter card that can activate W ake-On-LAN function, a client with W ake-On-LAN capa- bility , and software such as LDCM Rev . 3.10 or up that can trigger wake-up frame.
ASUS P2V User’ s Manual 61 (This page was intentionally left blank.)
62 ASUS P2V User’ s Manual (This page was intentionally left blank.)
ASUS P2V User’ s Manual 63 (This page was intentionally left blank.)
64 ASUS P2V User’ s Manual (This page was intentionally left blank.)