Asus Motherboard P5MT-M Product Manual

Motherboard P5MT-M
ii ii ii ii ii E2094 E2094 E2094 E2094 E2094 First Edition First Edition First Edition First Edition First Edition July 2005 July 2005 July 2005 July 2005 July 2005 Copyright © 2005 ASUST eK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”). Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.
iii iii iii iii iii Contents Notices ................................................................................................ vi Safety information ............................................................................. vii About this guide ............................................................................... viii P5MT-M specifications summary .......................................................... x Chapter 1: Chapter 1: Chapter 1: Chapter 1: Chapter 1: Product introduction Product introduction Product introduction Product introduction Product introduction 1.1 Welcome! .............................................................................. 1-1 1.2 Package contents ................................................................. 1-1 1.3 Special features .................................................................... 1-2 1.3.1 Product highlights ................................................... 1-2 1.3.2 Innovative ASUS features ....................................... 1-4 Chapter 2: Chapter 2: Chapter 2: Chapter 2: Chapter 2: Hardware information Hardware information Hardware information Hardware information Hardware information 2.1 Before you proceed .............................................................. 2-1 2.2 Motherboard overview .......................................................... 2-2 2.2.1 Placement direction ................................................ 2-2 2.2.2 Screw holes ............................................................ 2-2 2.2.3 Motherboard layout ................................................ 2-3 2.2.4 Layout contents ..................................................... 2-4 2.3 Central Processing Unit (CPU) .............................................. 2-6 2.3.1 Installing the CPU .................................................... 2-6 2.3.2 Installing the CPU heatsink and fan ........................ 2-9 2.3.3 Uninstalling the CPU heatsink and fan .................. 2-11 2.4 System memory ................................................................. 2-13 2.4.1 Overview ............................................................... 2-13 2.4.2 Memory configurations ......................................... 2-13 2.4.3 Installing a DIMM ................................................... 2-15 2.4.4 Removing a DIMM ................................................. 2-15 2.5 Expansion slots ................................................................... 2-16 2.5.1 Installing an expansion card .................................. 2-16 2.5.2 Configuring an expansion card .............................. 2-16 2.5.3 Interrupt assignments .......................................... 2-17 2.5.4 PCI Express x8 slots ............................................. 2-18 2.5.5 PCI slots ................................................................ 2-18 2.6 Jumpers .............................................................................. 2-19 2.7 Connectors ......................................................................... 2-24 2.7.1 Rear panel connectors .......................................... 2-24 2.7.2 Internal connectors ............................................... 2-25
iv iv iv iv iv Contents Chapter 3: Powering up Chapter 3: Powering up Chapter 3: Powering up Chapter 3: Powering up Chapter 3: Powering up 3.1 Starting up for the first time ................................................ 3-1 3.2 Turning off the computer ..................................................... 3-2 3.2.1 Using the OS shut down function ........................... 3-2 3.2.2 Using the dual function power switch .................... 3-2 Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup 4.1 Managing and updating your BIOS ........................................ 4-1 4.1.1 Creating a bootable floppy disk .............................. 4-1 4.1.2 ASUS EZ Flash utility .............................................. 4-2 4.1.3 AFUDOS utility ........................................................ 4-3 4.1.4 ASUS CrashFree BIOS 2 utility ................................ 4-6 4.1.5 ASUS Update utility ................................................ 4-8 4.2 BIOS setup program ........................................................... 4-11 4.2.1 BIOS menu screen ................................................. 4-12 4.2.2 Menu bar ............................................................... 4-12 4.2.3 Navigation keys .................................................... 4-12 4.2.4 Menu items ........................................................... 4-13 4.2.5 Sub-menu items ................................................... 4-13 4.2.6 Configuration fields .............................................. 4-13 4.2.7 Pop-up window ..................................................... 4-13 4.2.8 Scroll bar .............................................................. 4-13 4.2.9 General help .......................................................... 4-13 4.3 Main menu .......................................................................... 4-14 4.3.1 System Time ......................................................... 4-14 4.3.2 System Date ......................................................... 4-14 4.3.3 Legacy Diskette A ................................................ 4-14 4.3.4 Primary, Third, and Fourth IDE Master/Slave ........ 4-15 4.3.5 IDE Configuration .................................................. 4-16 4.3.6 System Information .............................................. 4-18 4.4 Advanced menu .................................................................. 4-19 4.4.1 USB Configuration ................................................. 4-19 4.4.2 MPS Configuration ................................................ 4-20 4.4.3 Remote Access Configuration .............................. 4-21 4.4.4 CPU Configuration ................................................. 4-22 4.4.5 Chipset ................................................................. 4-23 4.4.6 Onboard Devices Configuration ............................ 4-25 4.4.7 PCI PnP ................................................................. 4-26
v v v v v Contents 4.5 Power menu ........................................................................ 4-27 4.5.1 ACPI APIC Support [Enabled] ................................ 4-27 4.5.2 APM Configuration ................................................ 4-28 4.5.3 Hardware Monitor ................................................. 4-29 4.6 Boot menu .......................................................................... 4-31 4.6.1 Boot Device Priority .............................................. 4-31 4.6.2 Boot Settings Configuration ................................. 4-32 4.6.3 Security ................................................................ 4-33 4.7 Exit menu ........................................................................... 4-35 Chapter 5: RAID support Chapter 5: RAID support Chapter 5: RAID support Chapter 5: RAID support Chapter 5: RAID support 5.1 RAID configuration ................................................................ 5-1 5.1.1 RAID definitions ...................................................... 5-1 5.1.2 Installing Serial ATA hard disks ............................... 5-2 5.1.3 Intel ® RAID configurations ...................................... 5-2 5.1.4 LSI Logic Embedded SATA RAID Setup Utility ...... 5-13 Chapter 6: Driver installation Chapter 6: Driver installation Chapter 6: Driver installation Chapter 6: Driver installation Chapter 6: Driver installation 6.1 RAID driver installation ......................................................... 6-1 6.1.1 Creating a RAID driver disk ..................................... 6-1 6.1.2 Installing the Intel ® ICH7R RAID controller driver .... 6-3 6.2 LAN driver installation .......................................................... 6-7 6.2.1 Windows ® 2000/2003 Server ................................ 6-7 6.2.2 Red Hat ® Linux 9.0 ................................................. 6-9 6.3 VGA driver installation ........................................................ 6-11 6.3.1 Windows ® 2000 Server ........................................ 6-11 6.3.2 Windows ® 2003 Server ........................................ 6-12 6.3.3 Red Hat ® Linux 9.0 ............................................... 6-12 Appendix: Reference information Appendix: Reference information Appendix: Reference information Appendix: Reference information Appendix: Reference information A.1 P5MT-M block diagram ......................................................... A-1
vi vi vi vi vi Notices Federal Communications Commission Statement Federal Communications Commission Statement Federal Communications Commission Statement Federal Communications Commission Statement Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Canadian Department of Communications Statement Canadian Department of Communications Statement Canadian Department of Communications Statement Canadian Department of Communications Statement Canadian Department of Communications Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. This class B digital apparatus complies with Canadian This class B digital apparatus complies with Canadian This class B digital apparatus complies with Canadian This class B digital apparatus complies with Canadian This class B digital apparatus complies with Canadian ICES-003. ICES-003. ICES-003. ICES-003. ICES-003. The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
vii vii vii vii vii Safety information Electrical safety Electrical safety Electrical safety Electrical safety Electrical safety • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device. • Before connecting or removing signal cables from the motherboard, ensure that all power cables are unplugged. • Seek professional assistance before using an adapter or extension cord. These devices could interrupt the grounding circuit. • Make sure that your power supply is set to the correct voltage in your area. If you are not sure about the voltage of the electrical outlet you are using, contact your local power company. • If the power supply is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer. Operation safety Operation safety Operation safety Operation safety Operation safety • Before installing the motherboard and adding devices on it, carefully read all the manuals that came with the package. • Before using the product, make sure all cables are correctly connected and the power cables are not damaged. If you detect any damage, contact your dealer immediately. • To avoid short circuits, keep paper clips, screws, and staples away from connectors, slots, sockets and circuitry. • Avoid dust, humidity, and temperature extremes. Do not place the product in any area where it may become wet. • Place the product on a stable surface. • If you encounter technical problems with the product, contact a qualified service technician or your retailer.
viii viii viii viii viii About this guide This user guide contains the information you need when installing and configuring the motherboard. How this guide is organized How this guide is organized How this guide is organized How this guide is organized How this guide is organized This manual contains the following parts: • • • • • Chapter 1: Product introduction Chapter 1: Product introduction Chapter 1: Product introduction Chapter 1: Product introduction Chapter 1: Product introduction This chapter describes the features of the motherboard and the new technology it supports. • • • • • Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information This chapter lists the hardware setup procedures that you have to perform when installing system components. It includes description of the switches, jumpers, and connectors on the motherboard. • • • • • Chapter 3: Powering up Chapter 3: Powering up Chapter 3: Powering up Chapter 3: Powering up Chapter 3: Powering up This chapter describes the power up sequence, the vocal POST messages, and ways of shutting down the system. • • • • • Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Tells how to change system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided. • • • • • Chapter 5: RAID support Chapter 5: RAID support Chapter 5: RAID support Chapter 5: RAID support Chapter 5: RAID support Provides information on RAID configurations for this motherboard. • • • • • Chapter 6: Driver installation Chapter 6: Driver installation Chapter 6: Driver installation Chapter 6: Driver installation Chapter 6: Driver installation This chapter provides information on RAID, LAN and VGA driver installation for this motherboard. • • • • • Appendix Appendix Appendix Appendix Appendix : Reference information : Reference information : Reference information : Reference information : Reference information This appendix includes additional information that you may refer to when configuring the motherboard. Where to find more information Where to find more information Where to find more information Where to find more information Where to find more information Refer to the following sources for additional information and for product and software updates. 1. 1. 1. 1. 1. ASUS websites ASUS websites ASUS websites ASUS websites ASUS websites The ASUS website provides updated information on ASUS hardware and software products. Refer to the ASUS contact information. 2. 2. 2. 2. 2. Optional documentation Optional documentation Optional documentation Optional documentation Optional documentation Your product package may include optional documentation, such as warranty flyers, that may have been added by your dealer. These documents are not part of the standard package.
ix ix ix ix ix Conventions used in this guide Conventions used in this guide Conventions used in this guide Conventions used in this guide Conventions used in this guide To make sure that you perform certain tasks properly, take note of the following symbols used throughout this manual. Typography Typography Typography Typography Typography Bold text Bold text Bold text Bold text Bold text Indicates a menu or an item to select. Italics Used to emphasize a word or a phrase. <Key> Keys enclosed in the less-than and greater-than sign means that you must press the enclosed key. Example: <Enter> means that you must press the Enter or Return key. <Key1 Key2 Key3> If you must press two or more keys simultaneously, the key names are linked with a plus sign ( ). Example: <Ctrl Alt D> Command Command Command Command Command Means that you must type the command exactly as shown, then supply the required item or value enclosed in brackets. Example: At the DOS prompt, type the command line: afudos /i[filename] afudos /iP5MT-M.ROM DANGER/WARNING: DANGER/WARNING: DANGER/WARNING: DANGER/WARNING: DANGER/WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: CAUTION: CAUTION: CAUTION: CAUTION: Information to prevent damage to the components when trying to complete a task. NOTE: NOTE: NOTE: NOTE: NOTE: Tips and additional information to help you complete a task. IMPORTANT: IMPORTANT: IMPORTANT: IMPORTANT: IMPORTANT: Instructions that you MUST follow to complete a task.
x x x x x P5MT-M specifications summary (continued on the next page) CPU CPU CPU CPU CPU Chipset Chipset Chipset Chipset Chipset Front Side Bus Front Side Bus Front Side Bus Front Side Bus Front Side Bus Memory Memory Memory Memory Memory Expansion slots Expansion slots Expansion slots Expansion slots Expansion slots Storage Storage Storage Storage Storage Graphics Graphics Graphics Graphics Graphics LAN LAN LAN LAN LAN USB USB USB USB USB Special features Special features Special features Special features Special features BIOS features BIOS features BIOS features BIOS features BIOS features Rear panel Rear panel Rear panel Rear panel Rear panel LGA775 socket for Intel ® Pentium ® Processor Extreme Edition/Intel ® Pentium ® D/Celeron processor with Extended Memory 64-bit Technology (EM64T) Supports Intel ® Hyper-Threading Technology Northbridge: Intel ® E7230 Southbridge: Intel ® ICH7R 1066/800 MHz Dual-channel memory architecture 4 x 240-pin DIMM sockets support unbuffered ECC 667/533 MHz DDR2 memory modules Supports 256 MB up to 8 GB of system memory 1 x PCI Express™ x8 slot (x8 Link) 1 x PCI Express™ x8 slot (x4 Link) 2 x PCI 33 MHz slots (PCI 2.3) Intel ® ICH7R Southbridge supports: - 2 x Ultra DMA 100/66/33 hard disk drives - 4 x Serial ATA II hard disks with RAID 0, RAID 1, RAID 5, and RAID 10 configuration - Intel ® Matrix Storage Technology 1 x mini-PCI socket for ASUS ® Server Management Board ATI ® RAGE-XL PCI-based VGA controller Dual Broadcom BCM5721 Gigabit LAN controller (PCI Express 1.0a specifications compliant) Intel ® ICH7R Southbridge supports: - 8 x USB 2.0 ports (2 on the rear panel, 3 connectors at mid-board for up to 6 additional ports) ASUS Q-Fan ASUS CrashFree BIOS 2 ASUS MyLogo2™ ASUS EZ FLash AMI BIOS, 8 Mb FWH, Green, PnP, DMI2.0a, ACPI 2.0a, SMBIOS 2.3 1 x PS/2 keyboard port 1 x PS/2 mouse port 2 x USB 2.0 ports 1 x Serial (COM1) port 2 x LAN (RJ-45) ports 1 x VGA port 1 x Parallel port
xi xi xi xi xi P5MT-M specifications summary 1 x Floppy disk drive connector 1 x Hard disk activity LED connector 1x IDE connector 4 x Serial ATA connectors 2 x CPU fan connectors 4 x System fan connectors 1 x Serial port (COM2) connector 3 x USB connectors 1 x Parallel port connector 1 x 24-pin SSI power connector 1 x 4-pin ATX 12 V power connector 1 x Backplane SMBus connector 1 x Power supply SMBus connector 1 x BMC connector 1 x Ambient thermal sensor connector 1 x System panel auxiliary connector 1 x System panel connector SSI power supply (with 24-pin and 4-pin 12 V plugs) ATX 12V 2.0 compliant micro-ATX form factor: 9.6 ” x 9.6 ” (24.4 cm x 24.4 cm) Device drivers ASUS Update ASWM 2.0 Internal Internal Internal Internal Internal connectors connectors connectors connectors connectors Power Power Power Power Power Requirement Requirement Requirement Requirement Requirement Form Factor Form Factor Form Factor Form Factor Form Factor Support CD Support CD Support CD Support CD Support CD contents contents contents contents contents *Specifications are subject to change without notice.
xii xii xii xii xii
1 Product introduction This chapter describes the motherboard features and the new technologies it supports.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M Chapter summary 1 1.1 Welcome! .............................................................................. 1-1 1.2 Package contents ................................................................. 1-1 1.3 Special features .................................................................... 1-2
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 1-1 1-1 1-1 1-1 1-1 1.1 Welcome! Thank you for buying an ASUS Thank you for buying an ASUS Thank you for buying an ASUS Thank you for buying an ASUS Thank you for buying an ASUS ® ® ® ® ® P5MT-M motherboard! P5MT-M motherboard! P5MT-M motherboard! P5MT-M motherboard! P5MT-M motherboard! The motherboard delivers a host of new features and latest technologies, making it another standout in the long line of ASUS quality motherboards! Before you start installing the motherboard, and hardware devices on it, check the items in your package with the list below. 1.2 Package contents Check your motherboard package for the following items. Motherboard Motherboard Motherboard Motherboard Motherboard ASUS P5MT-M motherboard Cables Cables Cables Cables Cables 2-in-1 disk drive cable 4 x Serial ATA signal cables 2 x Serial ATA power cable 1 x USB PCI cable bracket Accessories Accessories Accessories Accessories Accessories I/O shield Application CD Application CD Application CD Application CD Application CD ASUS motherboard support CD Documentation Documentation Documentation Documentation Documentation User guide If any of the above items is damaged or missing, contact your retailer.
1-2 1-2 1-2 1-2 1-2 Chapter 1: Product introduction Chapter 1: Product introduction Chapter 1: Product introduction Chapter 1: Product introduction Chapter 1: Product introduction 1.3 Special features 1.3.1 1.3.1 1.3.1 1.3.1 1.3.1 Product highlights Product highlights Product highlights Product highlights Product highlights Latest processor technology Latest processor technology Latest processor technology Latest processor technology Latest processor technology The motherboard comes with a 775-pin surface mount Land Grid Array (LGA) socket designed for the Intel ® Pentium ® Processor Extreme Edition and the Intel ® Pentium ® D processor in the 775-land package, with 1066/ 800 MHz Front Side Bus (FSB). See page 2-6 for details. Intel Intel Intel Intel Intel ® E7230/Intel E7230/Intel E7230/Intel E7230/Intel E7230/Intel ® ICH7R chipset ICH7R chipset ICH7R chipset ICH7R chipset ICH7R chipset The Intel ® E7230 and the Intel ® ICH7R I/O controller hub (ICH)provide the vital interfaces for the motherboard. The uniprocessor server chipset integrates EM64T support and four Serial ATA ports enabled through the Serial ATA 3 Gb/s RAID controller to ensure data security and enable powerful multi-task processing. Intel Intel Intel Intel Intel ® EM64T EM64T EM64T EM64T EM64T The motherboard supports the Intel ® Hyper-Threading technology and incorporates the Extended Memory 64-bit Technology (EM64T). The Intel ® EM64T feature allows your system to run on 64-bit operating systems and access larger amounts of system memory for faster and more efficient computing. DDR2 memory support DDR2 memory support DDR2 memory support DDR2 memory support DDR2 memory support The motherboard supports DDR2 memory, which features data transfer rates of 667 MHz or 533 MHz to meet the higher bandwidth requirements of the latest 3D graphics, multimedia, and Internet applications. The dual-channel DDR2 architecture doubles the bandwidth of your system memory to boost system performance, eliminating bottlenecks with peak bandwidths of up to 10.7 GB/s. See page 2-13 for details. Serial ATA II technology Serial ATA II technology Serial ATA II technology Serial ATA II technology Serial ATA II technology The motherboard supports the Serial ATA II technology through the Serial ATA II interfaces controlled by the Intel ® ICH7R. The SATA II specification allows for thinner, more flexible cables with lower pin count, reduced voltage requirement, and up to 300 MB/s data transfer rate. See page 2-27 for details.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 1-3 1-3 1-3 1-3 1-3 PCI Express™ interface PCI Express™ interface PCI Express™ interface PCI Express™ interface PCI Express™ interface The motherboard fully supports PCI Express, the latest I/O interconnect technology that speeds up the PCI bus. PCI Express features point-to-point serial interconnections between devices and allows higher clockspeeds by carrying data in packets. This high speed interface is software compatible with existing PCI specifications. See page 2-1 8 for details. Dual Gigabit LAN solution Dual Gigabit LAN solution Dual Gigabit LAN solution Dual Gigabit LAN solution Dual Gigabit LAN solution The motherboard comes with onboard dual Gigabit LAN controllers to provide a total solution for your networking needs. The onboard Broadcom BCM5721 controllers use the PCI Express interface with a network throughput close to Gigabit bandwidth. See pages 2-21, 2-22, and 2-24 for details. Serial ATA RAID solution Serial ATA RAID solution Serial ATA RAID solution Serial ATA RAID solution Serial ATA RAID solution Onboard RAID controllers provide the motherboard with RAID functionality. The Intel ® ICH7R allows RAID 0, RAID 1, RAID 5, and RAID 10 configuration for four Serial ATA connectors and supports the Intel ® Matrix Technology. See page 2-27 for details. USB 2.0 technology USB 2.0 technology USB 2.0 technology USB 2.0 technology USB 2.0 technology The motherboard implements the Universal Serial Bus (USB) 2.0 specification, dramatically increasing the connection speed from the 12 Mbps bandwidth on USB 1.1 to a fast 480 Mbps on USB 2.0. USB 2.0 is backward compatible with USB 1.1. See pages 2-20 and 2-29 for details.
1-4 1-4 1-4 1-4 1-4 Chapter 1: Product introduction Chapter 1: Product introduction Chapter 1: Product introduction Chapter 1: Product introduction Chapter 1: Product introduction 1.3.2 1.3.2 1.3.2 1.3.2 1.3.2 Innovative ASUS features Innovative ASUS features Innovative ASUS features Innovative ASUS features Innovative ASUS features ASUS Smart Fan technology ASUS Smart Fan technology ASUS Smart Fan technology ASUS Smart Fan technology ASUS Smart Fan technology The ASUS Smart Fan technology smartly adjusts the fan speeds according to the system loading to ensure quiet, cool, and efficient operation. See page 4-30 for details. ASUS MyLogo2™ ASUS MyLogo2™ ASUS MyLogo2™ ASUS MyLogo2™ ASUS MyLogo2™ This feature allows you to personalize and add style to your system with customizable boot logos. See page 4-33 for details. ASUS EZ Flash BIOS ASUS EZ Flash BIOS ASUS EZ Flash BIOS ASUS EZ Flash BIOS ASUS EZ Flash BIOS With the ASUS EZ Flash, you can easily update the system BIOS even before loading the operating system. No need to use a DOS-based utility or boot from a floppy disk. See page 4-2 for details. ASUS CrashFree BIOS 2 ASUS CrashFree BIOS 2 ASUS CrashFree BIOS 2 ASUS CrashFree BIOS 2 ASUS CrashFree BIOS 2 This feature allows you to restore the original BIOS data from the support CD in case when the BIOS codes and data are corrupted. This protection eliminates the need to buy a replacement ROM chip. See page 4-6 for details.
2 Hardware information This chapter lists the hardware setup procedures that you have to perform when installing system components. It includes description of the jumpers and connectors on the motherboard.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M Chapter summary 2 2.1 Before you proceed .............................................................. 2-1 2.2 Motherboard overview .......................................................... 2-2 2.3 Central Processing Unit (CPU) .............................................. 2-6 2.4 System memory ................................................................. 2-13 2.5 Expansion slots ................................................................... 2-16 2.6 Jumpers .............................................................................. 2-19 2.7 Connectors ......................................................................... 2-24
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 2-1 2-1 2-1 2-1 2-1 Onboard LED Onboard LED Onboard LED Onboard LED Onboard LED The motherboard comes with a standby power LED. The green LED lights up to indicate that the system is ON, in sleep mode, or in soft-off mode. This is a reminder that you should shut down the system and unplug the power cable before removing or plugging in any motherboard component. The illustration below shows the location of the onboard LED. 2.1 Before you proceed Take note of the following precautions before you install motherboard components or change any motherboard settings. • Unplug the power cord from the wall socket before touching any component. • Use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, before handling components to avoid damaging them due to static electricity. • Hold components by the edges to avoid touching the ICs on them. • Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that came with the component. • Before you install or remove any component, ensure Before you install or remove any component, ensure Before you install or remove any component, ensure Before you install or remove any component, ensure Before you install or remove any component, ensure that the power supply is switched off or the power that the power supply is switched off or the power that the power supply is switched off or the power that the power supply is switched off or the power that the power supply is switched off or the power cord is detached from the power supply. cord is detached from the power supply. cord is detached from the power supply. cord is detached from the power supply. cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, and/or components. P5MT-M LAN2 ® P5MT -M Onboard LED SB_PWR1 OFF Powere d Off ON Standby Power
2-2 2-2 2-2 2-2 2-2 Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information P5MT -M LAN2 ® 2.2 Motherboard overview Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. Refer to the chassis documentation before installing the motherboard. Make sure to unplug the chassis power cord before installing or removing the motherboard. Failure to do so can cause you physical injury and damage motherboard components. Do not overtighten the screws! Doing so can damage the motherboard. 2.2.1 2.2.1 2.2.1 2.2.1 2.2.1 Placement direction Placement direction Placement direction Placement direction Placement direction When installing the motherboard, make sure that you place it into the chassis in the correct orientation. The edge with external ports goes to the rear part of the chassis as indicated in the image below. 2.2.2 2.2.2 2.2.2 2.2.2 2.2.2 Screw holes Screw holes Screw holes Screw holes Screw holes Place eight (8) screws into the holes indicated by circles to secure the motherboard to the chassis. Place this side towards Place this side towards Place this side towards Place this side towards Place this side towards the rear of the chassis the rear of the chassis the rear of the chassis the rear of the chassis the rear of the chassis
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 2-3 2-3 2-3 2-3 2-3 2.2.3 2.2.3 2.2.3 2.2.3 2.2.3 Motherboard layout Motherboard layout Motherboard layout Motherboard layout Motherboard layout P5MT -M 8Mbit Flash BIOS Super I/O PRI_IDE1 A TXPWR1 24.5cm (9.6in) 24.5cm (9.6in) DDR2 DIMM_A1 (64 bit,240-pin module) DDR2 DIMM_B1 (64 bit,240-pin module) DDR2 DIMM_A2 (64 bit,240-pin module) DDR2 DIMM_B2 (64 bit,240-pin module) AT I RAGE XL VGA Controller AUX_P ANEL1 REAR_F AN1 KBPWR1 PSUSMB1 CR2032 3V Lithium Cell CMOS Power PS/2KBMS T : Mouse B: Keyboard LAN1 LAN2 ® USB12 COM1 P ARALLEL PORT VGA1 USBPW12 REAR_F AN2 A TX12V1 FM_CPU2 CPU_F AN2 FM_CPU1 CPU_F AN1 PCIE2 PCI2 FRNT_F AN1 S ATA 1 P ANEL1 RECOVERY1 USB34 HDLED1 BUZZ1 FLOPPY1 BMCCONN1 TRPWR1 CLRTC1 BPSMB1 VGA_EN1 SB_PWR1 COM2 LAN_EN2 LAN_EN1 Broadcom BCM5721 Broadcom BCM5721 Intel ® E7230 Intel ® ICH7R BMCSOCKET1 LAN2 LGA775 PCIE1 PCI1 S ATA 2 S ATA 3 S ATA 4 FRNT_F AN2 USB56 USB78 USBPW34 USBPW56 USBPW78 LPT2 RAID_SEL1
2-4 2-4 2-4 2-4 2-4 Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information 2.2.4 2.2.4 2.2.4 2.2.4 2.2.4 Layout contents Layout contents Layout contents Layout contents Layout contents Slots Slots Slots Slots Slots Page Page Page Page Page 1. CPU sockets 2-6 2. DDR2 DIMM sockets 2-13 3. PCI Express/PCI slots 2-18 Jumpers Jumpers Jumpers Jumpers Jumpers Page Page Page Page Page 1. Clear RTC RAM (CLRTC1) 2-19 2. CPU fan pin selection (3-pin FM_CPU1, FM_CPU2) 2-20 3. USB device wake-up (3-pin USBPW12, USBPW34, USBPW56, 2-20 USBPW78) 4. Keyboard power (3-pin KBPWR1) 2-21 5. Gigabit LAN controller setting (3-pin LAN_EN1) 2-21 6. Gigabit LAN controller setting (3-pin LAN_EN2) 2-22 7. VGA graphics controller setting (3-pin VGA_EN1) 2-22 8. BIOS recovery (3-pin RECOVERY1) 2-23 9. RAID select (3-pin RAID_SEL1) 2-23 Rear panel connectors Rear panel connectors Rear panel connectors Rear panel connectors Rear panel connectors Page Page Page Page Page 1. PS/2 mouse port (green) 2-24 2. Parallel port 2-24 3. PS/2 keyboard port (purple) 2-24 4. USB 2.0 ports 1 and 2 2-24 5. Serial (COM1) port 2-24 6. VGA port 2-24 7. LAN 1 (RJ-45) port 2-24 8. LAN 2 (RJ-45) port 2-24
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 2-5 2-5 2-5 2-5 2-5 Internal connectors Internal connectors Internal connectors Internal connectors Internal connectors Page Page Page Page Page 1. Floppy disk drive connector (34-1 pin FLOPPY1) 2-25 2. Hard disk activity LED connector (4-pin HDLED1) 2-25 3. IDE connector (40-1 pin PRI_IDE1)) 2-26 4. Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4) 2-27 5. CPU fan connectors (4-pin CPU_FAN1/CPU_FAN2)) 2-28 6. System fan connectors (3-pin REAR_FAN1/REAR_FAN2, 2-28 FRNT_FAN1/FRNT_FAN2) 7. Serial port connector (10-1 pin COM2) 2-28 8. USB connectors (10-1 pin USB34, USB56, USB78) 2-29 9. Parallel port connector (26-1 pin LPT2) 2-29 10. SSI power connectors (24-pin ATXPWR1, 4 -pin A TX 12V1) 2-30 11. Backplane SMBus connector (6-1 pin BPSMB1) 2-31 12. Power supply SMBus connector (6-1 pin PSUSMB1) 2-31 13. BMC connector (16-pin BMCCONN1) 2-32 14. Ambient thermal sensor connector (2-pin TRPWR1) 2-32 15. System panel auxiliary connector (20-pin AUX_PANEL1) 2-33 • Chassis Intrusion connector (3-pin CASEOPEN) • LAN1 link activity LED (2-pin LAN1_LINKACTLED) • LAN2 link activity LED (2-pin LAN2_LINKACTLED) • Locator LED 1 (2-pin LOCATORLED1) • Locator LED 2 (2-pin LOCATORLED2) • Locator Button/Switch (2-pin LOCATORBTN) • Front Panel SMBus (6-1 pin) 16. System panel connector (20-pin PANEL1) 2-34 • System power LED (Green 3-pin POWERLED) • Hard disk drive activity LED (Red 2-pin HDLED) • System warning speaker (Orange 4-pin SPKROUT) • ATX power button/soft-off button (Yellow 2-pin POWERBTN) • Reset button (Blue 2-pin RESETBTN)
2-6 2-6 2-6 2-6 2-6 Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information 2.3.1 2.3.1 2.3.1 2.3.1 2.3.1 Installing the CPU Installing the CPU Installing the CPU Installing the CPU Installing the CPU To install a CPU: 1. Locate the CPU socket on the motherboard. 2.3 Central Processing Unit (CPU) The motherboard comes with a surface mount LGA775 socket designed for the Intel ® Pentium ® 4 processor in the 775-land package. Before installing the CPU, make sure that the socket box is facing towards you and the load lever is on your left. • Your boxed Intel ® Pentium ® 4 LGA775 processor package should come with installation instructions for the CPU and heatsink. If the instructions in this section do not match the CPU documentation, follow the latter. • Upon purchase of the motherboard, make sure that the PnP cap is on the socket and the socket contacts are not bent. Contact your retailer immediately if the PnP cap is missing, or if you see any damage to the PnP cap/socket contacts/motherboard components. ASUS will shoulder the cost of repair only if the damage is shipment/ transit-related. • Keep the cap after installing the motherboard. ASUS will process Return Merchandise Authorization (RMA) requests only if the motherboard comes with the cap on the LGA775 socket. • The product warranty does not cover damage to the socket contacts resulting from incorrect CPU installation/removal, or misplacement/loss/incorrect removal of the PnP cap. P5MT-M LAN2 ® P5MT -M CPU Socket 775
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 2-7 2-7 2-7 2-7 2-7 3. Lift the load lever in the direction of the arrow to a 135º angle. 4. Lift the load plate with your thumb and forefinger to a 100º angle (A), then push the PnP cap from the load plate window to remove (B). To prevent damage to the socket pins, do not remove the PnP cap unless you are installing a CPU. 5. Position the CPU over the socket, making sure that the gold triangle is on the bottom-left corner of the socket. The socket alignment key should fit into the CPU notch. Alignment key Alignment key Alignment key Alignment key Alignment key Gold triangle mark Gold triangle mark Gold triangle mark Gold triangle mark Gold triangle mark Load plate Load plate Load plate Load plate Load plate A B 2. Press the load lever with your thumb (A), then move it to the left (B) until it is released from the retention tab. Retention tab Retention tab Retention tab Retention tab Retention tab Load lever Load lever Load lever Load lever Load lever This side of the This side of the This side of the This side of the This side of the socket box should socket box should socket box should socket box should socket box should face you. face you. face you. face you. face you. PnP cap PnP cap PnP cap PnP cap PnP cap A B
2-8 2-8 2-8 2-8 2-8 Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Notes on Intel Notes on Intel Notes on Intel Notes on Intel Notes on Intel ® Hyper-Threading Technology Hyper-Threading Technology Hyper-Threading Technology Hyper-Threading Technology Hyper-Threading Technology • This motherboard supports Intel ® Pentium ® 4 CPUs in the 775-land package with Hyper-Threading Technology. • Hyper-Threading Technology is supported under Windows ® XP/2003 Server and Linux 2.4.x (kernel) and later versions only. Under Linux, use the Hyper-Threading compiler to compile the code. If you are using any other operating systems, disable the Hyper-Threading Technology item in the BIOS to ensure system stability and performance. • Installing Windows ® 2003 Server or later version is recommended. • Make sure to enable the Hyper-Threading Technology item in BIOS before installing a supported operating system. • For more information on Hyper-Threading Technology, visit www.intel.com/info/hyperthreading. To use the Hyper-Threading Technology on this motherboard: 1. Install an Intel ® Pentium ® 4 CPU that supports Hyper-Threading Technology. 2. Power up the system and enter the BIOS Setup (see Chapter 4: BIOS setup). Under the Advanced Menu, make sure that the item Hyper-Threading Technology is set to Enabled. The item appears only if you installed a CPU that supports Hyper-Threading Technology. 3. Reboot the computer. The CPU fits in only one correct orientation. DO NOT force the CPU into the socket to prevent bending the connectors on the socket and damaging the CPU! 6. Close the load plate (A), then push the load lever (B) until it snaps into the retention tab. A B
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 2-9 2-9 2-9 2-9 2-9 Fastener Fastener Fastener Fastener Fastener Motherboard hole Motherboard hole Motherboard hole Motherboard hole Motherboard hole 2.3.2 2.3.2 2.3.2 2.3.2 2.3.2 Installing the CPU heatsink and fan Installing the CPU heatsink and fan Installing the CPU heatsink and fan Installing the CPU heatsink and fan Installing the CPU heatsink and fan The Intel ® Pentium ® 4 LGA775 processor requires a specially designed heatsink and fan assembly to ensure optimum thermal condition and performance. • When you buy a boxed Intel ® Pentium ® 4 processor, the package includes the CPU fan and heatsink assembly. If you buy a CPU separately, make sure that you use only Intel ® -certified multi-directional heatsink and fan. • Your Intel ® Pentium ® 4 LGA775 heatsink and fan assembly comes in a push-pin design and requires no tool to install. • If you purchased a separate CPU heatsink and fan assembly, make sure that you have properly applied Thermal Interface Material to the CPU heatsink or CPU before you install the heatsink and fan assembly. Make sure to orient each fastener with the narrow end of the groove pointing outward. (The photo shows the groove shaded for emphasis.) To install the CPU heatsink and fan: 1. Place the heatsink on top of the installed CPU, making sure that the four fasteners match the holes on the motherboard. Narrow end Narrow end Narrow end Narrow end Narrow end of the groove of the groove of the groove of the groove of the groove Make sure that you have installed the motherboard to the chassis before you install the CPU fan and heatsink assembly. Orient the heatsink and fan assembly such that the CPU fan cable is closest to the CPU fan connector.
2-10 2-10 2-10 2-10 2-10 Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information 3. Connect the CPU fan cable to the connector on the motherboard labeled CPU_FAN1/CPU_FAN2. • Do not forget to connect the CPU fan connector! Hardware monitoring errors can occur if you fail to plug this connector. • If there is only one CPU fan cable, connect it to the connector labeled CPU_FAN1. Failure to do so may cause hardware monitoring errors. 2. Push down two fasteners at a time in a diagonal sequence to secure the heatsink and fan assembly in place. B B A A A A B B P5MT-M LAN2 ® P5MT -M CPU fan connectors GND F ANPWR2 F ANOUT4 CPU_F AN 2 CPU_F AN 1 GND F ANPWR2 F ANOUT4 CPU_F AN2 CPU_F AN1
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 2-11 2-11 2-11 2-11 2-11 2.3.3 2.3.3 2.3.3 2.3.3 2.3.3 Uninstalling the CPU heatsink and fan Uninstalling the CPU heatsink and fan Uninstalling the CPU heatsink and fan Uninstalling the CPU heatsink and fan Uninstalling the CPU heatsink and fan To uninstall the CPU heatsink and fan: 1. Disconnect the CPU fan cable from the connector on the motherboard. 2. Rotate each fastener counterclockwise. 3. Pull up two fasteners at a time in a diagonal sequence to disengage the heatsink and fan assembly from the motherboard. B B A A A A B B
2-12 2-12 2-12 2-12 2-12 Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information 4. Carefully remove the heatsink and fan assembly from the motherboard. 5. Rotate each fastener clockwise to ensure correct orientation when reinstalling. The narrow end of the groove should point outward after resetting. (The photo shows the groove shaded for emphasis.) Narrow end of the groove Narrow end of the groove Narrow end of the groove Narrow end of the groove Narrow end of the groove
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 2-13 2-13 2-13 2-13 2-13 2.4 System memory 2.4.1 2.4.1 2.4.1 2.4.1 2.4.1 Overview Overview Overview Overview Overview The motherboard comes with four Double Data Rate 2 (DDR2) Dual Inline Memory Modules (DIMM) sockets. A DDR2 module has the same physical dimensions as a DDR DIMM but has a 240-pin footprint compared to the 184-pin DDR DIMM. DDR2 DIMMs are notched to match the break on the socket and ensure correct installation. The figure illustrates the location of the DDR2 DIMM sockets: 2.4.2 2.4.2 2.4.2 2.4.2 2.4.2 Memory configurations Memory configurations Memory configurations Memory configurations Memory configurations You may install 256 MB, 512 MB and 1 GB unbuffered ECC/non-ECC DDR2 533/667 MHz DIMMs into the DIMM sockets. Always install DIMMs with the same CAS latency. For optimum compatibility, it is recommended that you obtain memory modules from the same vendor. P5MT-M LAN2 ® P5MT -M 240-pin DDR2 DIMM sockets DIMM_A 1 DIMM_B 2 DIMM_B 1 DIMM_A 2 1 12 Pins 128 Pins Notes on capacity and installation of four 1 GB memory Notes on capacity and installation of four 1 GB memory Notes on capacity and installation of four 1 GB memory Notes on capacity and installation of four 1 GB memory Notes on capacity and installation of four 1 GB memory modules modules modules modules modules • Due to chipset resource allocation, system configuration determines the system memory availability. The system typically shows about 3~4 GB available memory space due to chipset resource allocation for onboard devices and add-on cards. This will vary for different add-on cards that the user installs. Some PCI cards need larger memory space, which will make the total available memory space below 3 GB. • To prevent compatibility issues, do not combine single and double-sided memory modules on the same motherboard/system.
2-14 2-14 2-14 2-14 2-14 Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Recommended memory configurations Recommended memory configurations Recommended memory configurations Recommended memory configurations Recommended memory configurations * Use only identical DDR2 DIMM pairs. * Use only identical DDR2 DIMM pairs. * Use only identical DDR2 DIMM pairs. * Use only identical DDR2 DIMM pairs. * Use only identical DDR2 DIMM pairs. Sockets Sockets Sockets Sockets Sockets Mode Mode Mode Mode Mode DIMM_A1 DIMM_A1 DIMM_A1 DIMM_A1 DIMM_A1 DIMM_A2 DIMM_A2 DIMM_A2 DIMM_A2 DIMM_A2 DIMM_B1 DIMM_B1 DIMM_B1 DIMM_B1 DIMM_B1 DIMM_B2 DIMM_B2 DIMM_B2 DIMM_B2 DIMM_B2 (blue) (blue) (blue) (blue) (blue) (black) (black) (black) (black) (black) (blue) (blue) (blue) (blue) (blue) (black) (black) (black) (black) (black) Single-channel (1) Installed — — — Dual-channel* (1) Installed — Installed — (2) Installed Installed Installed Installed Microsoft Microsoft Microsoft Microsoft Microsoft ® ® ® ® ® OS memory support OS memory support OS memory support OS memory support OS memory support Refer to the table below for the maximum memory support information on various Microsoft ® operating systems. Microsoft Microsoft Microsoft Microsoft Microsoft ® ® ® ® ® operating system operating system operating system operating system operating system Maximum physical Maximum physical Maximum physical Maximum physical Maximum physical memory supported memory supported memory supported memory supported memory supported Windows ® 2000 Professional 4 GB Windows ® 2000 Server 4 GB Windows ® 2000 Advanced Server 8 GB Windows ® 2000 Datacenter Server 32 GB Windows ® XP Professional 4 GB Windows ® XP 64-bit Edition 32 GB Windows ® Server 2003 Web Edition 2 GB Windows ® Server 2003 Standard Edition 4 GB Windows ® Server 2003 Enterprise Edition 32 GB Windows ® Server 2003 Datacenter Edition 64 GB Windows ® Server 2003 Enterprise 64-bit Edition 64 GB Windows ® Server 2003 Datacenter 64-bit Edition 512 GB The memory support information was gathered from various public Microsoft ® web pages.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 2-15 2-15 2-15 2-15 2-15 2.4.3 2.4.3 2.4.3 2.4.3 2.4.3 Installing a DIMM Installing a DIMM Installing a DIMM Installing a DIMM Installing a DIMM Unplug the power supply before adding or removing DIMMs or other system components. Failure to do so can cause severe damage to both the motherboard and the components. To install a DIMM: 1. Unlock a DIMM socket by pressing the retaining clips outward. 2. Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket. 3. Firmly insert the DIMM into the socket until the retaining clips snap back in place and the DIMM is properly seated. 2.4.4 2.4.4 2.4.4 2.4.4 2.4.4 Removing a DIMM Removing a DIMM Removing a DIMM Removing a DIMM Removing a DIMM To remove a DIMM: 1. Simultaneously press the retaining clips outward to unlock the DIMM. 2. Remove the DIMM from the socket. • A DDR2 DIMM is keyed with a notch so that it fits in only one direction. Do not force a DIMM into a socket to avoid damaging the DIMM. • The DDR2 DIMM sockets do not support DDR DIMMs. DO not install DDR DIMMs to the DDR2 DIMM sockets. Unlocked retaining clip Unlocked retaining clip Unlocked retaining clip Unlocked retaining clip Unlocked retaining clip DDR2 DIMM notch DDR2 DIMM notch DDR2 DIMM notch DDR2 DIMM notch DDR2 DIMM notch Support the DIMM lightly with your fingers when pressing the retaining clips. The DIMM might get damaged when it flips out with extra force. DDR2 DIMM notch DDR2 DIMM notch DDR2 DIMM notch DDR2 DIMM notch DDR2 DIMM notch 1 2 3 1 2 1
2-16 2-16 2-16 2-16 2-16 Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information 2.5 Expansion slots In the future, you may need to install expansion cards. The following sub-sections describe the slots and the expansion cards that they support. 2.5.1 2.5.1 2.5.1 2.5.1 2.5.1 Installing an expansion card Installing an expansion card Installing an expansion card Installing an expansion card Installing an expansion card To install an expansion card: 1. Before installing the expansion card, read the documentation that came with it and make the necessary hardware settings for the card. 2. Remove the system unit cover (if your motherboard is already installed in a chassis). 3. Remove the bracket opposite the slot that you intend to use. Keep the screw for later use. 4. Align the card connector with the slot and press firmly until the card is completely seated on the slot. 5. Secure the card to the chassis with the screw you removed earlier. 6. Replace the system cover. 2.5.2 2.5.2 2.5.2 2.5.2 2.5.2 Configuring an expansion card Configuring an expansion card Configuring an expansion card Configuring an expansion card Configuring an expansion card After installing the expansion card, configure the it by adjusting the software settings. 1. Turn on the system and change the necessary BIOS settings, if any. See Chapter 4 for information on BIOS setup. 2. Assign an IRQ to the card. Refer to the tables on the next page. 3. Install the software drivers for the expansion card. Make sure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components. When using PCI cards on shared slots, ensure that the drivers support “Share IRQ” or that the cards do not need IRQ assignments. Otherwise, conflicts will arise between the two PCI groups, making the system unstable and the card inoperable.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 2-17 2-17 2-17 2-17 2-17 2.5.3 2.5.3 2.5.3 2.5.3 2.5.3 Interrupt assignments Interrupt assignments Interrupt assignments Interrupt assignments Interrupt assignments Standard interrupt assignments Standard interrupt assignments Standard interrupt assignments Standard interrupt assignments Standard interrupt assignments IRQ IRQ IRQ IRQ IRQ Priority Priority Priority Priority Priority Standard Function Standard Function Standard Function Standard Function Standard Function 0 1 System Timer 1 2 Keyboard Controller 2 — Re-direct to IRQ #9 3 11 Communications Port (COM2)* 4 12 Communications Port (COM1)* 5 13 IRQ holder for PCI steering* 6 14 Floppy Disk Controller 7 15 Printer Port (LPT1)* 8 3 System CMOS/Real Time Clock 9 4 IRQ holder for PCI steering* 10 5 IRQ holder for PCI steering* 11 6 IRQ holder for PCI steering* 12 7 PS/2 Compatible Mouse Port* 13 8 Numeric Data Processor 14 9 Primary IDE Channel 15 10 Secondary IDE Channel * These IRQs are usually available for ISA or PCI devices. * These IRQs are usually available for ISA or PCI devices. * These IRQs are usually available for ISA or PCI devices. * These IRQs are usually available for ISA or PCI devices. * These IRQs are usually available for ISA or PCI devices. IRQ assignments for this motherboard IRQ assignments for this motherboard IRQ assignments for this motherboard IRQ assignments for this motherboard IRQ assignments for this motherboard A A A A A B B B B B C C C C C D D D D D E E E E E F F F F F G G G G G H H H H H PCI slot 1 — — — — shared — — — PCI slot 2 — — — — — — shared — PCI E x8 slot shared — — — ———— PCI E x8 slot shared — — — ———— Onboard USB controller 1 shared — — — ———— Onboard USB controller 2 — shared — — ———— Onboard USB controller 3 — — used — ———— Onboard USB controller 4 — — — shared ———— Onboard USB 2.0 controller shared — — — ———— Onboard IDE port shared — — — ———— Onboard SATA port — shared — — ———— Onboard PCI E x1 LAN1 shared — — — ———— Onboard PCI E x1 LAN2 — shared — — ———— Onboard VGA — — — — shared — — — When using PCI cards on shared slots, ensure that the drivers support “Share IRQ” or that the cards do not need IRQ assignments; otherwise, conflicts will arise between the two PCI groups, making the system unstable and the card inoperable.
2-18 2-18 2-18 2-18 2-18 Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information 2.5.5 2.5.5 2.5.5 2.5.5 2.5.5 PCI slots PCI slots PCI slots PCI slots PCI slots The PCI slots support cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI 2.3 specifications. The figure shows a LAN card installed on a PCI slot. 32-bit PCI slot 32-bit PCI slot 32-bit PCI slot 32-bit PCI slot 32-bit PCI slot 2.5.4 2.5.4 2.5.4 2.5.4 2.5.4 PCI Express x8 slots PCI Express x8 slots PCI Express x8 slots PCI Express x8 slots PCI Express x8 slots This motherboard supports PCI Express x8 network cards, SCSI cards, and other cards that comply with PCI Express 1.0 specifications. PCI Express x8 slots PCI Express x8 slots PCI Express x8 slots PCI Express x8 slots PCI Express x8 slots
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 2-19 2-19 2-19 2-19 2-19 1. 1. 1. 1. 1. Clear RTC RAM (CLRTC1) Clear RTC RAM (CLRTC1) Clear RTC RAM (CLRTC1) Clear RTC RAM (CLRTC1) Clear RTC RAM (CLRTC1) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords. To erase the RTC RAM: 1. Turn OFF the computer and unplug the power cord. 2. Remove the onboard battery. 3. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the cap on pins 2-3 for about 5~10 seconds, then move the cap back to pins 1-2. 4. Re-install the battery. 5. Plug the power cord and turn ON the computer. 6. Hold down the <Del> key during the boot process and enter BIOS setup to re-enter data. Except when clearing the RTC RAM, never remove the cap on CLRTC jumper default position. Removing the cap will cause system boot failure! 2.6 Jumpers P5MT-M LAN2 ® P5MT -M Clear RTC RAM CLRTC1 Normal (Default) Clear CMOS 2 3 2 1
2-20 2-20 2-20 2-20 2-20 Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information 3. 3. 3. 3. 3. USB device wake-up (3-pin USBPW12, USBPW34, USB device wake-up (3-pin USBPW12, USBPW34, USB device wake-up (3-pin USBPW12, USBPW34, USB device wake-up (3-pin USBPW12, USBPW34, USB device wake-up (3-pin USBPW12, USBPW34, USBPW56, USBPW78) USBPW56, USBPW78) USBPW56, USBPW78) USBPW56, USBPW78) USBPW56, USBPW78) Set these jumpers to 5V to wake up the computer from S1 sleep mode (CPU stopped, DRAM refreshed, system running in low power mode) using the connected USB devices. Set to 5VSB to wake up from S4 sleep mode (no power to CPU and DRAM, power supply in reduced power mode). • The USB device wake-up feature requires a power supply that can provide 500mA on the 5VSB lead for each USB port; otherwise, the system would not power up. • The total current consumed must NOT exceed the power supply capability ( 5VSB) whether under normal condition or in sleep mode. 2. 2. 2. 2. 2. CPU fan pin selection (3-pin FM_CPU1, FM_CPU2) CPU fan pin selection (3-pin FM_CPU1, FM_CPU2) CPU fan pin selection (3-pin FM_CPU1, FM_CPU2) CPU fan pin selection (3-pin FM_CPU1, FM_CPU2) CPU fan pin selection (3-pin FM_CPU1, FM_CPU2) These jumpers allow you to connect either a 3-pin or a 4-pin fan cable plug to the CPU fan connectors (CPU_FAN1, CPU_FAN2). Set these jumpers to pins 1-2 if you are using a 3-pin fan cable plug, or to pins 2-3 if you are using a 4-pin plug. P5MT-M LAN2 ® P5MT -M FM CPU Setting FM_CPU1 FM_CPU2 12 23 3-pin fan 4-pin fan (Default) 2 3 2 1 3-pin fan 4-pin fan (Default) P5MT-M LAN2 ® P5MT -M USB device wake-up USBPW12 (Defaul t) 5V 5VSB 21 32 USBPW78 USBPW56 USBPW34 (Defaul t) 5V 5VSB 21 32 (Defaul t) 5V 5VSB 21 32 (Defaul t) 5V 5VSB 21 32
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 2-21 2-21 2-21 2-21 2-21 4. 4. 4. 4. 4. Keyboard power (3-pin KBPWR1) Keyboard power (3-pin KBPWR1) Keyboard power (3-pin KBPWR1) Keyboard power (3-pin KBPWR1) Keyboard power (3-pin KBPWR1) This jumper allows you to enable or disable the keyboard wake-up feature. Set this jumper to pins 2-3 ( 5VSB) to wake up the computer when you press a key on the keyboard (the default is the Space Bar). This feature requires an ATX power supply that can supply at least 1A on the 5VSB lead, and a corresponding setting in the BIOS. 5. 5. 5. 5. 5. Gigabit LAN controller setting (3-pin LAN_EN1) Gigabit LAN controller setting (3-pin LAN_EN1) Gigabit LAN controller setting (3-pin LAN_EN1) Gigabit LAN controller setting (3-pin LAN_EN1) Gigabit LAN controller setting (3-pin LAN_EN1) These jumpers allow you to enable or disable the onboard Broadcom BCM5721 Gigabit LAN controller. Set to pins 1-2 to activate the Gigabit LAN feature. P5MT-M LAN2 ® P5MT -M Keyboard power setting KBPWR1 (Default) 5V 5VSB 2 3 1 2 P5MT-M LAN2 ® P5MT -M LAN_EN1 setting Enable (Default) Disabl e LAN_EN1 2 1 2 3
2-22 2-22 2-22 2-22 2-22 Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information 7. 7. 7. 7. 7. VGA graphics controller setting (3-pin VGA_EN1) VGA graphics controller setting (3-pin VGA_EN1) VGA graphics controller setting (3-pin VGA_EN1) VGA graphics controller setting (3-pin VGA_EN1) VGA graphics controller setting (3-pin VGA_EN1) These jumpers allow you to enable or disable the onboard ATI Rage XL video graphics controller. Set to pins 1-2 to enable the video graphics controller. 6. 6. 6. 6. 6. Gigabit LAN controller setting (3-pin LAN_EN2) Gigabit LAN controller setting (3-pin LAN_EN2) Gigabit LAN controller setting (3-pin LAN_EN2) Gigabit LAN controller setting (3-pin LAN_EN2) Gigabit LAN controller setting (3-pin LAN_EN2) These jumpers allow you to enable or disable the onboard Broadcom BCM5721 Gigabit LAN controller. Set to pins 1-2 to activate the Gigabit LAN feature. Make sure to set this jumper to Disable Disable Disable Disable Disable i f you want to install VGA cards on the PCI and PCI Express slots. P5MT-M LAN2 ® P5MT -M LAN_EN2 setting Enable (Default) Disabl e LAN_EN2 2 3 1 2 P5MT-M LAN2 ® P5MT -M VGA setting VGA_EN1 Enable (Default) Disabl e 23 12
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 2-23 2-23 2-23 2-23 2-23 8. 8. 8. 8. 8. BIOS recovery (3-pin RECOVERY1) BIOS recovery (3-pin RECOVERY1) BIOS recovery (3-pin RECOVERY1) BIOS recovery (3-pin RECOVERY1) BIOS recovery (3-pin RECOVERY1) This jumper allows you to recover your original BIOS from a floppy disk in case the BIOS codes and data are corrupted. To recover the BIOS: 1. Turn OFF your computer and unplug the power cord. 2. Move the jumper cap from pins 1-2 (default) to pins 2-3. 3. Insert a floppy disk with the original or updated BIOS file. 4. Plug the power cord and turn ON the computer. 5. The system searches for the BIOS file in the floppy then reflashes the BIOS. 6. When finished, shut down your computer. 7. Replace the jumper cap from pins 2-3 to pins 1-2. 8. Reboot your computer. 9. Hold down the <Del> <Del> <Del> <Del> <Del> key during the boot process and enter BIOS setup to re-enter data. P5MT-M LAN2 ® P5MT -M BIOS recovery setting RECOVERY1 (Default) Normal BIOS recover y 23 12 9. 9. 9. 9. 9. RAID select setting (3-pin RAID_SEL1) RAID select setting (3-pin RAID_SEL1) RAID select setting (3-pin RAID_SEL1) RAID select setting (3-pin RAID_SEL1) RAID select setting (3-pin RAID_SEL1) Set this jumper to 1-2 (Default) to enable LSI RAID ROM. Set this jumper to 2-3 to enable Intel ® RAID ROM. P5MT-M LAN2 ® 12 23 P5MT -M RAID select jumper RAID_SEL1 LSI RAID ROM (Default) INTEL RAID ROM
2-24 2-24 2-24 2-24 2-24 Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information 2.7 Connectors 2.7.1 2.7.1 2.7.1 2.7.1 2.7.1 Rear panel connectors Rear panel connectors Rear panel connectors Rear panel connectors Rear panel connectors 1. 1. 1. 1. 1. PS/2 mouse port (green). PS/2 mouse port (green). PS/2 mouse port (green). PS/2 mouse port (green). PS/2 mouse port (green). This port is for a PS/2 mouse. 2. 2. 2. 2. 2. Parallel port. Parallel port. Parallel port. Parallel port. Parallel port. This 25-pin port connects a parallel printer, a scanner, or other devices. 3. 3. 3. 3. 3. PS/2 keyboard port (purple). PS/2 keyboard port (purple). PS/2 keyboard port (purple). PS/2 keyboard port (purple). PS/2 keyboard port (purple). This port is for a PS/2 keyboard. 4. 4. 4. 4. 4. USB 2.0 ports 1 and 2. USB 2.0 ports 1 and 2. USB 2.0 ports 1 and 2. USB 2.0 ports 1 and 2. USB 2.0 ports 1 and 2. These two 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2.0 devices. 5. 5. 5. 5. 5. Serial (COM1) port Serial (COM1) port Serial (COM1) port Serial (COM1) port Serial (COM1) port . This 9-pin communication port is for pointing devices or other serial devices. 6. 6. 6. 6. 6. Video Graphics Adapter (VGA) port. Video Graphics Adapter (VGA) port. Video Graphics Adapter (VGA) port. Video Graphics Adapter (VGA) port. Video Graphics Adapter (VGA) port. This port is for a VGA monitor or other VGA-compatible devices. 7 7 7 7 7 . . . . . LAN 1 (RJ-45) port. LAN 1 (RJ-45) port. LAN 1 (RJ-45) port. LAN 1 (RJ-45) port. LAN 1 (RJ-45) port. This port allows Gigabit connection to a Local Area Network (LAN) through a network hub. Refer to the table below for the LAN port LED indications. 8. 8. 8. 8. 8. LAN 2 (RJ-45) port. LAN 2 (RJ-45) port. LAN 2 (RJ-45) port. LAN 2 (RJ-45) port. LAN 2 (RJ-45) port. This port allows Gigabit connection to a Local Area Network (LAN) through a network hub. Refer to the table below for the LAN port LED indications. LAN port LED indications LAN port LED indications LAN port LED indications LAN port LED indications LAN port LED indications ACT/LINK LED ACT/LINK LED ACT/LINK LED ACT/LINK LED ACT/LINK LED SPEED LED SPEED LED SPEED LED SPEED LED SPEED LED Status Status Status Status Status Description Description Description Description Description Status Status Status Status Status Description Description Description Description Description OFF No link OFF 10 Mbps connection GREEN Linked ORANGE 100 Mbps connection BLINKING Data activity GREEN 1 Gbps connection LAN port LAN port LAN port LAN port LAN port SPEED SPEED SPEED SPEED SPEED LED LED LED LED LED ACT/LINK ACT/LINK ACT/LINK ACT/LINK ACT/LINK LED LED LED LED LED 1 3 6 5 7 8 4 2
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 2-25 2-25 2-25 2-25 2-25 2.7.2 2.7.2 2.7.2 2.7.2 2.7.2 Internal connectors Internal connectors Internal connectors Internal connectors Internal connectors 1. 1. 1. 1. 1. Floppy disk drive connector (34-1 pin FLOPPY1) Floppy disk drive connector (34-1 pin FLOPPY1) Floppy disk drive connector (34-1 pin FLOPPY1) Floppy disk drive connector (34-1 pin FLOPPY1) Floppy disk drive connector (34-1 pin FLOPPY1) This connector is for the provided floppy disk drive (FDD) signal cable. Insert one end of the cable to this connector, then connect the other end to the signal connector at the back of the floppy disk drive. Pin 5 on the connector is removed to prevent incorrect cable connection when using a FDD cable with a covered Pin 5. 2. 2. 2. 2. 2. Hard disk activity LED connector (4-pin HDLED1) Hard disk activity LED connector (4-pin HDLED1) Hard disk activity LED connector (4-pin HDLED1) Hard disk activity LED connector (4-pin HDLED1) Hard disk activity LED connector (4-pin HDLED1) This connector supplies power to the hard disk activity LED for add-on cards such as SCSI or RAID cards. The read/write activities of the add-on cards cause the hard disk activity LED to light up. P5MT-M LAN2 ® NOTE: Orient the red markings o n the floppy ribbon cable to PIN 1. P5MT -M Floppy disk drive connector FLOPPY1 PIN 1 P5MT-M LAN2 ® P5MT -M Hard disk activity LED connector HDLED 1 1 ADD_IN_CARD_ACT# NC ADD_IN_CARD_ACT# NC
2-26 2-26 2-26 2-26 2-26 Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information 3. 3. 3. 3. 3. IDE connector (40-1 pin PRI_IDE1) IDE connector (40-1 pin PRI_IDE1) IDE connector (40-1 pin PRI_IDE1) IDE connector (40-1 pin PRI_IDE1) IDE connector (40-1 pin PRI_IDE1) This connector is for an Ultra DMA 100/66 signal cable. The Ultra DMA 100/66 signal cable has three connectors: a blue connector for the primary IDE connector on the motherboard, a black connector for an Ultra DMA 100/66 IDE slave device (optical drive/hard disk drive), and a gray connector for an Ultra DMA 100/66 IDE master device (hard disk drive). If you install two hard disk drives, you must configure the second drive as a slave device by setting its jumper accordingly. Refer to the hard disk documentation for the jumper settings. • Pin 20 on the IDE connector is removed to match the covered hole on the Ultra DMA cable connector. This prevents incorrect insertion when you connect the IDE cable. • Use the 80-conductor IDE cable for Ultra DMA 100/66 IDE devices. P5MT-M LAN2 ® P5MT -M IDE connector NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1. PRI_IDE1 PIN 1
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 2-27 2-27 2-27 2-27 2-27 4. 4. 4. 4. 4. Serial ATA connectors (7-pin SATA1, SATA2, SATA3, Serial ATA connectors (7-pin SATA1, SATA2, SATA3, Serial ATA connectors (7-pin SATA1, SATA2, SATA3, Serial ATA connectors (7-pin SATA1, SATA2, SATA3, Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4) SATA4) SATA4) SATA4) SATA4) These connectors are for the Serial ATA signal cables for Serial ATA hard disk drives. If you installed Serial ATA hard disk drives, you can create a RAID 0, RAID 1, RAID 5, or RAID 10 configuration with the onboard Intel ® ICH7R RAID controller. These connectors are set to Standard IDE Standard IDE Standard IDE Standard IDE Standard IDE mode by default. In S S S S S tandard IDE tandard IDE tandard IDE tandard IDE tandard IDE mode, you can connect Serial ATA boot/data hard disk drives to these connectors. If you intend to create a Serial ATA RAID set using these connectors, set the Configure SATA Configure SATA Configure SATA Configure SATA Configure SATA a a a a a s s s s s item in the BIOS to [RAID]. See section “4.3.5 IDE Configuration” for details. When using the connectors in S S S S S tandard IDE tandard IDE tandard IDE tandard IDE tandard IDE mode, connect the primary (boot) hard disk drive to the SATA1 or SATA2 connector. Refer to the table below for the recommended SATA hard disk drive connections. Serial ATA hard disk drive connection Serial ATA hard disk drive connection Serial ATA hard disk drive connection Serial ATA hard disk drive connection Serial ATA hard disk drive connection Connector Connector Connector Connector Connector Setting Setting Setting Setting Setting Use Use Use Use Use SATA1, SATA2 SATA1, SATA2 SATA1, SATA2 SATA1, SATA2 SATA1, SATA2 Master Master Master Master Master Boot disk Boot disk Boot disk Boot disk Boot disk SATA3, SATA4 SATA3, SATA4 SATA3, SATA4 SATA3, SATA4 SATA3, SATA4 Slave Slave Slave Slave Slave Data disk Data disk Data disk Data disk Data disk P5MT-M LAN2 ® P5MT -M SA T A connectors S ATA 2 S ATA 1 S ATA 4 S ATA 3 GND RSA T A_TXP2 RSA T A_TXN2 GND RSA T A_RXP2 RSA T A_RXN2 GND GND RSA T A_TXP1 RSA T A_TXN1 GND RSA T A_RXP1 RSA T A_RXN1 GND GND RSA T A_TXP4 RSA T A_TXN4 GND RSA T A_RXP4 RSA T A_RXN4 GND GND RSA T A_TXP3 RSA T A_TXN3 GND RSA T A_RXP3 RSA T A_RXN3 GND
2-28 2-28 2-28 2-28 2-28 Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information 6. 6. 6. 6. 6. Serial port connector (10-1 pin COM2) Serial port connector (10-1 pin COM2) Serial port connector (10-1 pin COM2) Serial port connector (10-1 pin COM2) Serial port connector (10-1 pin COM2) This connector is for a serial (COM2) port. Connect the serial port module cable to this connector, then install the module to a slot opening at the back of the system chassis. 5. 5. 5. 5. 5. CPU and system fan connectors (4-pin CPU_FAN1/2, CPU and system fan connectors (4-pin CPU_FAN1/2, CPU and system fan connectors (4-pin CPU_FAN1/2, CPU and system fan connectors (4-pin CPU_FAN1/2, CPU and system fan connectors (4-pin CPU_FAN1/2, 3-pin REAR_FAN1/2, 3-pin FRNT_FAN1/2) 3-pin REAR_FAN1/2, 3-pin FRNT_FAN1/2) 3-pin REAR_FAN1/2, 3-pin FRNT_FAN1/2) 3-pin REAR_FAN1/2, 3-pin FRNT_FAN1/2) 3-pin REAR_FAN1/2, 3-pin FRNT_FAN1/2) The fan connectors support cooling fans of 350 mA ~ 740 mA (8.88 W max.) or a total of 2.1 A ~ 4.44 A ( 5 3.28 W max.) at 12V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector. Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. These are not jumpers! Do not place jumper caps on the fan connectors! P5MT-M LAN2 ® P5MT -M Fan connectors REAR_F AN 2 REAR_F AN1 FRNT_F AN1 FRNT_F AN 2 GND F ANPWR2 F ANOUT4 CPU_F AN2 CPU_F AN1 GND F ANPWR3 F ANOUT7 GND Rotation 12V CPU_F AN2 REAR_F AN2 REAR_F AN1 FRNT_F AN1 FRNT_F AN2 CPU_F AN1 GND Rotation 12V GND Rotation 12V GND Rotation 12V P5MT-M LAN2 ® P5MT -M Serial port2 (COM2) connector PIN 1 COM2
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 2-29 2-29 2-29 2-29 2-29 7. 7. 7. 7. 7. USB connector (10-1 pin USB34, USB56, USB78) USB connector (10-1 pin USB34, USB56, USB78) USB connector (10-1 pin USB34, USB56, USB78) USB connector (10-1 pin USB34, USB56, USB78) USB connector (10-1 pin USB34, USB56, USB78) This connector is for USB 2.0 ports. Connect the USB module cable to this connector, then install the module to a slot opening at the back of the system chassis. The USB connector complies with USB 2.0 specification that supports up to 480 Mbps connection speed. Never connect a 1394 cable 1394 cable 1394 cable 1394 cable 1394 cable t o the USB connectors. Doing so will damage the motherboard! 8. 8. 8. 8. 8. Parallel port connector (26-1 pin LPT2) Parallel port connector (26-1 pin LPT2) Parallel port connector (26-1 pin LPT2) Parallel port connector (26-1 pin LPT2) Parallel port connector (26-1 pin LPT2) This connector is a parallel port module that connects a parallel printer, a scanner, or other devices. P5MT-M LAN2 ® P5MT -M USB 2.0 connectors USB78 USB 5V 1 USB_P8 - USB_P8 GND USB 5V USB_P7- USB _P7 GND NC USB 5V 1 USB_P6 - USB_P6 GND USB 5V USB_P5- USB _P5 GND NC USB 5V 1 USB_P4 - USB_P4 GND USB 5V USB_P3- USB _P3 GND NC USB56 USB34 P5MT-M LAN2 ® P5MT -M Parallel port connector LPT2 SPD7 GND SPD6 GND SPD5 GND SPD4 GND SLCT PE GND BUSY ACK# GND SPD3 GND SPD2 SLIN# SPD1 PINIT# SPD0 ERROR# STB# AFD# GND Pin 1
2-30 2-30 2-30 2-30 2-30 Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information 9. 9. 9. 9. 9. SSI SSI SSI SSI SSI power connectors power connectors power connectors power connectors power connectors (24-pin ATXPWR1, (24-pin ATXPWR1, (24-pin ATXPWR1, (24-pin ATXPWR1, (24-pin ATXPWR1, 4 4 4 4 4 -pin -pin -pin -pin -pin ATX ATX ATX ATX ATX 12V1) 12V1) 12V1) 12V1) 12V1) These connectors are for SSI power supply plugs. The power supply plugs are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. • Use of an SSI 12 V Specification 2.0-compliant power supply unit (PSU) that provides a minimum power of 450 W is recommended for a fully-configured system. • Do not forget to connect the 4 -pin A TX 12V1 power plug; otherwise, the system will not boot up. • Use of a PSU with a higher power output is recommended when configuring a system with more power consuming devices. The system may become unstable or may not boot up if the power is inadequate. • You must install a PSU with a higher power rating if you intend to install additional devices. P5MT-M LAN2 ® P5MT -M A TX power connectors 24-pin Power Connector A TX12V1 12V DC GND 12V DC GND A TXPWR1 3 V olts 3 V olts Ground 5 V olts 5 V olts Ground Ground Power OK 5V Standby 12 V olts -5 V olts 5 V olts 3 V olts -12 V olts Ground Ground Ground PSON# Ground 5 V olts 12 V olts 3 V olts 5 V olts 1 Ground
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 2-31 2-31 2-31 2-31 2-31 10. 10. 10. 10. 10. Backplane SMBus connector (6-1 pin BPSMB1) Backplane SMBus connector (6-1 pin BPSMB1) Backplane SMBus connector (6-1 pin BPSMB1) Backplane SMBus connector (6-1 pin BPSMB1) Backplane SMBus connector (6-1 pin BPSMB1) This connector allows you to connect SMBus (System Management Bus) devices. Devices communicate with an SMBus host and/or other SMBus devices using the SMBus interface. 11. 11. 11. 11. 11. Power supply SMBus connector (6-1 pin PSUSMB1) Power supply SMBus connector (6-1 pin PSUSMB1) Power supply SMBus connector (6-1 pin PSUSMB1) Power supply SMBus connector (6-1 pin PSUSMB1) Power supply SMBus connector (6-1 pin PSUSMB1) This connector allows you to connect SMBus (System Management Bus) devices. Devices communicate with an SMBus host and/or other SMBus devices using the SMBus interface. P5MT-M LAN2 ® P5MT -M SMBus connector BPSMB1 1 12CCLK_P2 GND I2CDA T A_P2 5V HWM_REARF ANOU T P5MT-M LAN2 ® P5MT -M Power supply SMBus connector PSUSMB1 3.3V Remote Sense GND NC PSU_I2CDA T A PSU_I2CCLK
2-32 2-32 2-32 2-32 2-32 Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information 12. 12. 12. 12. 12. BMC connector (16-pin BMCCONN1) BMC connector (16-pin BMCCONN1) BMC connector (16-pin BMCCONN1) BMC connector (16-pin BMCCONN1) BMC connector (16-pin BMCCONN1) This connector is for an ASUS server management card. 13. 13. 13. 13. 13. Ambient thermal sensor connector (2-pin TRPWR1) Ambient thermal sensor connector (2-pin TRPWR1) Ambient thermal sensor connector (2-pin TRPWR1) Ambient thermal sensor connector (2-pin TRPWR1) Ambient thermal sensor connector (2-pin TRPWR1) If you want additional thermal monitoring, connect the thermal sensor cable with a thermistor (of 1ºK or at 25ºC, B=3435) to this connector. P5MT-M LAN2 ® P5MT -M BMC connector BMCCONN1 5VSB 5VSB BMC SMBCLK 12CCLK1 PSON# BMC_RST# PWROK PSONEN# 5VSB 5VSB BMC SMBDA T A 12CDA T A1 FP_PWRBTN# BMC_PRESENT# BMC_SMI# GND P5MT-M LAN2 ® P5MT -M TRPWR connector TRPWR1 SYS-THEAMAL 2 GND
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 2-33 2-33 2-33 2-33 2-33 14. 14. 14. 14. 14. Auxiliary panel connector (20-pin AUX_PANEL1) Auxiliary panel connector (20-pin AUX_PANEL1) Auxiliary panel connector (20-pin AUX_PANEL1) Auxiliary panel connector (20-pin AUX_PANEL1) Auxiliary panel connector (20-pin AUX_PANEL1) This connector supports several server system functions. • Chassis Intrusion connector (3-pin CASEOPEN) Chassis Intrusion connector (3-pin CASEOPEN) Chassis Intrusion connector (3-pin CASEOPEN) Chassis Intrusion connector (3-pin CASEOPEN) Chassis Intrusion connector (3-pin CASEOPEN) This lead is for a chassis with an intrusion detection feature. This requires an external detection mechanism such as a chassis intrusion sensor or microswitch. When you remove any chassis component, the sensor triggers and sends a high-level signal to this lead to record a chassis intrusion event. • LAN1 link activity LED (2-pin LAN1_LINKACTLED) LAN1 link activity LED (2-pin LAN1_LINKACTLED) LAN1 link activity LED (2-pin LAN1_LINKACTLED) LAN1 link activity LED (2-pin LAN1_LINKACTLED) LAN1 link activity LED (2-pin LAN1_LINKACTLED) This 2-pin connector is for the LAN1 Activity LED. Connect the LAN1 Activity LED cable to this connector. This LED blinks during a network activity and is always lit when linked. • LAN2 link activity LED (2-pin LAN2_LINKACTLED) LAN2 link activity LED (2-pin LAN2_LINKACTLED) LAN2 link activity LED (2-pin LAN2_LINKACTLED) LAN2 link activity LED (2-pin LAN2_LINKACTLED) LAN2 link activity LED (2-pin LAN2_LINKACTLED) This 2-pin connector is for the LAN2 Activity LED. Connect the LAN2 Activity LED cable to this connector. This LED blinks during a network activity and lights up when linked. • Locator LED 1 (2-pin LOCATORLED1) Locator LED 1 (2-pin LOCATORLED1) Locator LED 1 (2-pin LOCATORLED1) Locator LED 1 (2-pin LOCATORLED1) Locator LED 1 (2-pin LOCATORLED1) This 2-pin connector is for the Locator LED 1. Connect the Locator LED 1 cable to this connector. This LED lights up when the Locator button is pressed and if there is no LAN1 connection (e.g. the LAN1 controller is broken). • Locator LED 2 (2-pin LOCATORLED2) Locator LED 2 (2-pin LOCATORLED2) Locator LED 2 (2-pin LOCATORLED2) Locator LED 2 (2-pin LOCATORLED2) Locator LED 2 (2-pin LOCATORLED2) This 2-pin connector is for the Locator LED 2. Connect the Locator LED 2 cable to this connector. This LED is synchronized with the LAN2 LED. • Locator Button/Switch (2-pin LOCATORBTN) Locator Button/Switch (2-pin LOCATORBTN) Locator Button/Switch (2-pin LOCATORBTN) Locator Button/Switch (2-pin LOCATORBTN) Locator Button/Switch (2-pin LOCATORBTN) This connector is for the locator button. This button queries the state of the system locator. • Front Panel SMBus (6-1 pin) Front Panel SMBus (6-1 pin) Front Panel SMBus (6-1 pin) Front Panel SMBus (6-1 pin) Front Panel SMBus (6-1 pin) This connector allows you to connect SMBus (System Management Bus) devices. Devices communicate with an SMBus host and/or other SMBus devices using the SMBus interface. P5MT-M LAN2 ® P5MT -M Auxiliary panel connector AUX_P ANEL1 I2C_4_DA T A# LOCA TORLED1 5VSB LOCA TORLED1- LAN1_LINKACTLED LOCA TORBTN# LAN1_LINKACTLED- GND 5VSB I2C_4_CLK# GND GND LAN2_LINKACTLED- LOCA TORLED2- LAN2_LINKACTLED LOCA TORLED2 CASEOPEN PIN1 NC
2-34 2-34 2-34 2-34 2-34 Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information Chapter 2: Hardware information • System power LED (Green 3-pin POWERLED) System power LED (Green 3-pin POWERLED) System power LED (Green 3-pin POWERLED) System power LED (Green 3-pin POWERLED) System power LED (Green 3-pin POWERLED) This 3-pin connector is for the system power LED. Connect the chassis power LED cable to this connector. The system power LED lights up when you turn on the system power, and blinks when the system is in sleep mode. • Hard disk drive activity LED (Red 2-pin HDLED) Hard disk drive activity LED (Red 2-pin HDLED) Hard disk drive activity LED (Red 2-pin HDLED) Hard disk drive activity LED (Red 2-pin HDLED) Hard disk drive activity LED (Red 2-pin HDLED) This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity LED cable to this connector. The IDE LED lights up or flashes when data is read from or written to the HDD. • System warning speaker (Orange 4-pin SPKROUT) System warning speaker (Orange 4-pin SPKROUT) System warning speaker (Orange 4-pin SPKROUT) System warning speaker (Orange 4-pin SPKROUT) System warning speaker (Orange 4-pin SPKROUT) This 4-pin connector is for the chassis-mounted system warning speaker. The speaker allows you to hear system beeps and warnings. • ATX power button/soft-off button ATX power button/soft-off button ATX power button/soft-off button ATX power button/soft-off button ATX power button/soft-off button (Yellow 2-pin POWERBTN) (Yellow 2-pin POWERBTN) (Yellow 2-pin POWERBTN) (Yellow 2-pin POWERBTN) (Yellow 2-pin POWERBTN) This connector is for the system power button. Pressing the power button turns the system on or puts the system in sleep or soft-off mode depending on the BIOS settings. Pressing the power switch for more than four seconds while the system is ON turns the system OFF. • Reset button (Blue 2-pin RESETBTN) Reset button (Blue 2-pin RESETBTN) Reset button (Blue 2-pin RESETBTN) Reset button (Blue 2-pin RESETBTN) Reset button (Blue 2-pin RESETBTN) This 2-pin connector is for the chassis-mounted reset button for system reboot without turning off the system power. 15. 15. 15. 15. 15. System panel connector (20-pin PANEL1) System panel connector (20-pin PANEL1) System panel connector (20-pin PANEL1) System panel connector (20-pin PANEL1) System panel connector (20-pin PANEL1) This connector supports several chassis-mounted functions. The sytem panel connector is color-coded for easy connection. P5MT-M LAN2 ® P5MT -M System panel connector P ANEL1 MLED- GND NC POWERBTN# 5V GND GND NC POWERLED HDLED GND HDLED- POWERLED- MLED NMIBTN# GND RESETBTN# SPKROUT GND
3 Powering up This chapter describes the power up sequence, the vocal POST messages, and ways of shutting down the system.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M Chapter summary 3 3.1 Starting up for the first time ................................................ 3-1 3.2 TUrning off the computer .................................................... 3-2
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 3-1 3-1 3-1 3-1 3-1 3.1 Starting up for the first time 1. After making all the connections, replace the system case cover. 2. Be sure that all switches are off. 3. Connect the power cord to the power connector at the back of the system chassis. 4. Connect the power cord to a power outlet that is equipped with a surge protector. 5. Turn on the devices in the following order: a. Monitor b. External SCSI devices (starting with the last device on the chain) c. System power 6. After applying power, the system power LED on the system front panel case lights up. For systems with ATX power supplies, the system LED lights up when you press the ATX power button. If your monitor complies with “green” standards or if it has a “power standby” feature, the monitor LED may light up or switch between orange and green after the system LED turns on. The system then runs the power-on self tests or POST. While the tests are running, the BIOS beeps (see BIOS beep codes table below) or additional messages appear on the screen. If you do not see anything within 30 seconds from the time you turned on the power, the system may have failed a power-on test. Check the jumper settings and connections or call your retailer for assistance. AMI BIOS beep codes AMI BIOS beep codes AMI BIOS beep codes AMI BIOS beep codes AMI BIOS beep codes Beep Description Beep Description Beep Description Beep Description Beep Description Error Error Error Error Error One beep Keyboard controller error Refresh Time error No master drive detected Two continuous beeps followed by Floppy controller failure two short beeps Two continuous beeps followed by Hardware component failure four short beeps 7. At power on, hold down the <Delete> key to enter the BIOS Setup. Follow the instructions in Chapter 4.
3-2 3-2 3-2 3-2 3-2 Chapter 3: Powering up Chapter 3: Powering up Chapter 3: Powering up Chapter 3: Powering up Chapter 3: Powering up 3.2 Turning off the computer 3.2.1 3.2.1 3.2.1 3.2.1 3.2.1 Using the OS shut down function Using the OS shut down function Using the OS shut down function Using the OS shut down function Using the OS shut down function If you are using Windows ® Server 2000: 1. Click the Start Start Start Start Start button then click Shut Down... Shut Down... Shut Down... Shut Down... Shut Down... 2. Make sure that the Shut Down Shut Down Shut Down Shut Down Shut Down option button is selected, then click the OK OK OK OK O K button to shut down the computer. 3. The power supply should turn off after Windows ® shuts down. If you are using Windows ® Server 2003: 1. Click the Start Start Start Start Start button then select Turn Off Computer. Turn Off Computer. Turn Off Computer. Turn Off Computer. Turn Off Computer. 2. Click the Turn Off Turn Off Turn Off Turn Off Turn Off button to shut down the computer. 3. The power supply should turn off after Windows ® shuts down. 3.2.2 3.2.2 3.2.2 3.2.2 3.2.2 Using the dual function power switch Using the dual function power switch Using the dual function power switch Using the dual function power switch Using the dual function power switch While the system is ON, pressing the power switch for less than four seconds puts the system to sleep mode or to soft-off mode, depending on the BIOS setting. Pressing the power switch for more than four seconds lets the system enter the soft-off mode regardless of the BIOS setting. Refer to section “4.5 Power Menu” in Chapter 4 for details.
4 BIOS setup This chapter tells how to change the system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M Chapter summary 4 4.1 Managing and updating your BIOS ........................................ 4-1 4.2 BIOS setup program ........................................................... 4-11 4.3 Main menu .......................................................................... 4-14 4.4 Advanced menu .................................................................. 4-19 4.5 Power menu ........................................................................ 4-27 4.6 Boot menu .......................................................................... 4-31 4.7 Exit menu ........................................................................... 4-35
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 4-1 4-1 4-1 4-1 4-1 4.1 Managing and updating your BIOS The following utilities allow you to manage and update the motherboard Basic Input/Output System (BIOS) setup. 1. ASUS AFUDOS ASUS AFUDOS ASUS AFUDOS ASUS AFUDOS ASUS AFUDOS (Updates the BIOS in DOS mode using a bootable floppy disk.) 2. ASUS EZ Flash ASUS EZ Flash ASUS EZ Flash ASUS EZ Flash ASUS EZ Flash (Updates the BIOS using a floppy disk during POST.) 3. ASUS CrashFree BIOS 2 ASUS CrashFree BIOS 2 ASUS CrashFree BIOS 2 ASUS CrashFree BIOS 2 ASUS CrashFree BIOS 2 (Updates the BIOS using a bootable floppy disk or the motherboard support CD when the BIOS file fails or gets corrupted.) 4. ASUS Update ASUS Update ASUS Update ASUS Update ASUS Update (Updates the BIOS in Windows ® environment.) Refer to the corresponding sections for details on these utilities. 4.1.1 4.1.1 4.1.1 4.1.1 4.1.1 Creating a bootable floppy disk Creating a bootable floppy disk Creating a bootable floppy disk Creating a bootable floppy disk Creating a bootable floppy disk 1. Do either one of the following to create a bootable floppy disk. DOS environment a. Insert a 1.44 MB floppy disk into the drive. b. At the DOS prompt, type format A:/S then press <Enter>. Windows ® XP environment a. Insert a 1.44 MB floppy disk to the floppy disk drive. b. Click Start Start Start Start Start from the Windows ® desktop, then select My My My My My Computer Computer Computer Computer Computer . c. Select the 3 1/2 Floppy Drive icon. d. Click File File File File File from the menu, then select Format Format Format Format Format . A Format 3 1/2 Format 3 1/2 Format 3 1/2 Format 3 1/2 Format 3 1/2 Floppy Disk Floppy Disk Floppy Disk Floppy Disk Floppy Disk window appears. e. Windows Windows Windows Windows Windows ® ® ® ® ® XP users: XP users: XP users: XP users: XP users: Select Create an MS-DOS startup Create an MS-DOS startup Create an MS-DOS startup Create an MS-DOS startup Create an MS-DOS startup disk disk disk disk disk from the format options field, then click Start Start Start Start Start . Save a copy of the original motherboard BIOS file to a bootable floppy disk in case you need to restore the BIOS in the future. Copy the original motherboard BIOS using the ASUS Update or AFUDOS utilities.
4-2 4-2 4-2 4-2 4-2 Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Windows ® 2000 environment To create a set of boot disks for Windows ® 2000: a. Insert a formatted, high density 1.44 MB floppy disk into the drive. b. Insert the Windows ® 2000 CD to the optical drive. c. Click Start Start Start Start Start , then select Run Run Run Run Run . d. In the Open Open Open Open Open field, type D:\bootdisk\makeboot a: assuming that D is your optical drive letter. e. Press <Enter>, then follow screen instructions to continue. 2. Copy the original or the latest motherboard BIOS file to the bootable floppy disk. 4.1.2 4.1.2 4.1.2 4.1.2 4.1.2 ASUS EZ Flash utility ASUS EZ Flash utility ASUS EZ Flash utility ASUS EZ Flash utility ASUS EZ Flash utility The ASUS EZ Flash feature allows you to update the BIOS without having to go through the long process of booting from a floppy disk and using a DOS-based utility. The EZ Flash utility is built-in the BIOS chip so it is accessible by pressing <Alt> <F2> during the Power-On Self Tests (POST). To update the BIOS using EZ Flash: 1. Visit the ASUS website (www.asus.com) to download the latest BIOS file for the motherboard and rename the same to P5MT-M.ROM. P5MT-M.ROM. P5MT-M.ROM. P5MT-M.ROM. P5MT-M.ROM. 2. Save the BIOS file to a floppy disk, then restart the system. 3. Press <Alt> <F2> during POST to display the following. EZFlash starting BIOS update Checking for floppy... 4. Insert the floppy disk that contains the BIOS file to the floppy disk drive. When the correct BIOS file is found, EZ Flash performs the BIOS update process and automatically reboots the system when done.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 4-3 4-3 4-3 4-3 4-3 4.1.3 4.1.3 4.1.3 4.1.3 4.1.3 AFUDOS utility AFUDOS utility AFUDOS utility AFUDOS utility AFUDOS utility The AFUDOS utility allows you to update the BIOS file in DOS environment using a bootable floppy disk with the updated BIOS file. This utility also allows you to copy the current BIOS file that you can use as backup when the BIOS fails or gets corrupted during the updating process. Copying the current BIOS Copying the current BIOS Copying the current BIOS Copying the current BIOS Copying the current BIOS To copy the current BIOS file using the AFUDOS utility: Main filename Main filename Main filename Main filename Main filename Extension name Extension name Extension name Extension name Extension name 1. Copy the AFUDOS utility (afudos.exe) from the motherboard support CD to the bootable floppy disk you created earlier. 2. Boot the system in DOS mode, then at the prompt type: afudos /o[filename] where the [filename] is any user-assigned filename not more than eight alphanumeric characters for the main filename and three alphanumeric characters for the extension name. A:\>afudos /oOLDBIOS1.rom • Make sure that the floppy disk is not write-protected and has at least 1024 KB free space to save the file. • The succeeding BIOS screens are for reference only. The actual BIOS screen displays may not be same as shown. EZFlash starting BIOS update Checking for floppy... Floppy found! Reading file “P5MT-M.ROM”. Completed. Start erasing.......| Start programming...| Flashed successfully. Rebooting. • Do not shut down or reset the system while updating the BIOS to prevent system boot failure! • A “Floppy not found!” error message appears if there is no floppy disk in the drive. A “P5MT-M.ROM not found!” error message appears if the correct BIOS file is not found in the floppy disk. Make sure that you rename the BIOS file to P5MT-M.ROM.
4-4 4-4 4-4 4-4 4-4 Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup 2. Copy the AFUDOS utility (afudos.exe) from the motherboard support CD to the bootable floppy disk you created earlier. 3. Boot the system in DOS mode, then at the prompt type: afudos /i[filename] /pbnc where [filename] is the latest or the original BIOS file on the bootable floppy disk. Updating the BIOS file Updating the BIOS file Updating the BIOS file Updating the BIOS file Updating the BIOS file To update the BIOS file using the AFUDOS utility: 1. Visit the ASUS website (www.asus.com) and download the latest BIOS file for the motherboard. Save the BIOS file to a bootable floppy disk. A:\>afudos /iP5MT-M.ROM /pbnc Write the BIOS filename on a piece of paper. You need to type the exact BIOS filename at the DOS prompt. The utility returns to the DOS prompt after copying the current BIOS file. 3. Press <Enter>. The utility copies the current BIOS file to the floppy disk. A:\>afudos /oOLDBIOS1.rom AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB)) Copyright (C) 2002 American Megatrends, Inc. All rights reserved. Reading flash ..... done Write to file...... ok A:\>
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 4-5 4-5 4-5 4-5 4-5 5. The utility returns to the DOS prompt after the BIOS update process is completed. Reboot the system from the hard disk drive. A:\>afudos /iP5MT-M.ROM /pbnc AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB)) Copyright (C) 2002 American Megatrends, Inc. All rights reserved. WARNING!! Do not turn off power during flash BIOS Reading file ....... done Reading flash ...... done Advance Check ...... Erasing flash ...... done Writing flash ...... 0x0008CC00 (9%) 4. The utility verifies the file and starts updating the BIOS. Do not shut down or reset the system while updating the BIOS to prevent system boot failure! A:\>afudos /iP5MT-M.ROM /pbnc AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB)) Copyright (C) 2002 American Megatrends, Inc. All rights reserved. WARNING!! Do not turn off power during flash BIOS Reading file ....... done Reading flash ...... done Advance Check ...... Erasing flash ...... done Writing flash ...... done Verifying flash .... done Please restart your computer A:\>
4-6 4-6 4-6 4-6 4-6 Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup 4.1.4 4.1.4 4.1.4 4.1.4 4.1.4 ASUS CrashFree BIOS 2 utility ASUS CrashFree BIOS 2 utility ASUS CrashFree BIOS 2 utility ASUS CrashFree BIOS 2 utility ASUS CrashFree BIOS 2 utility The ASUS CrashFree BIOS 2 is an auto recovery tool that allows you to restore the BIOS file when it fails or gets corrupted during the updating process. You can update a corrupted BIOS file using the motherboard support CD or the floppy disk that contains the updated BIOS file. Recovering the BIOS from a floppy disk Recovering the BIOS from a floppy disk Recovering the BIOS from a floppy disk Recovering the BIOS from a floppy disk Recovering the BIOS from a floppy disk To recover the BIOS from a floppy disk: 1. Turn on the system. 2. Insert the floppy disk with the original or updated BIOS file to the floppy disk drive. 3. The utility displays the following message and automatically checks the floppy disk for the original or updated BIOS file. Bad BIOS checksum. Starting BIOS recovery... Checking for floppy... 4. Restart the system after the utility completes the updating process. Bad BIOS checksum. Starting BIOS recovery... Checking for floppy... Floppy found! Reading file “P5MT-M.ROM”. Completed. Start flashing... When found, the utility reads the BIOS file and starts flashing the corrupted BIOS file. DO NOT shut down or reset the system while updating the BIOS! Doing so can cause system boot failure! • Prepare the motherboard support CD or the floppy disk containing the updated motherboard BIOS before using this utility. • Make sure that you rename the original or updated BIOS file in the floppy disk to P5MT-M.ROM P5MT-M.ROM P5MT-M.ROM P5MT-M.ROM P5MT-M.ROM .
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 4-7 4-7 4-7 4-7 4-7 The recovered BIOS may not be the latest BIOS version for this motherboard. Visit the ASUS website (www.asus.com) to download the latest BIOS file. Recovering the BIOS from the support CD Recovering the BIOS from the support CD Recovering the BIOS from the support CD Recovering the BIOS from the support CD Recovering the BIOS from the support CD To recover the BIOS from the support CD: 1. Remove any floppy disk from the floppy disk drive, then turn on the system. 2. Insert the support CD to the optical drive. 3. The utility displays the following message and automatically checks the floppy disk for the original or updated BIOS file. 4. Restart the system after the utility completes the updating process. DO NOT shut down or reset the system while updating the BIOS! Doing so can cause system boot failure! Bad BIOS checksum. Starting BIOS recovery... Checking for floppy... Floppy not found! Checking for CD-ROM... CD-ROM found! Reading file “P5MT-M.ROM”. Completed. Start flashing... When no floppy disk is found, the utility automatically checks the optical drive for the original or updated BIOS file. The utility then updates the corrupted BIOS file. Bad BIOS checksum. Starting BIOS recovery... Checking for floppy...
4-8 4-8 4-8 4-8 4-8 Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup 4.1.5 4.1.5 4.1.5 4.1.5 4.1.5 ASUS Update utility ASUS Update utility ASUS Update utility ASUS Update utility ASUS Update utility The ASUS Update is a utility that allows you to manage, save, and update the motherboard BIOS in Windows ® environment. The ASUS Update utility allows you to: • Save the current BIOS file • Download the latest BIOS file from the Internet • Update the BIOS from an updated BIOS file • Update the BIOS directly from the Internet, and • View the BIOS version information. This utility is available in the support CD that comes with the motherboard package. ASUS Update requires an Internet connection either through a network or an Internet Service Provider (ISP). Installing ASUS Update Installing ASUS Update Installing ASUS Update Installing ASUS Update Installing ASUS Update To install ASUS Update: 1. Place the support CD in the optical drive. The Drivers Drivers Drivers Drivers Drivers menu appears. 2. Click the Utilities Utilities Utilities Utilities Utilities tab, then click Install ASUS Update Install ASUS Update Install ASUS Update Install ASUS Update Install ASUS Update VX.XX.XX VX.XX.XX VX.XX.XX VX.XX.XX VX.XX.XX . 3. The ASUS Update utility is copied to your system. Quit all Windows ® applications before you update the BIOS using this utility.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 4-9 4-9 4-9 4-9 4-9 3. Select the ASUS FTP site nearest you to avoid network traffic, or click Auto Select Auto Select Auto Select Auto Select Auto Select . Click Next Next Next Next Next . Updating the BIOS through the Internet Updating the BIOS through the Internet Updating the BIOS through the Internet Updating the BIOS through the Internet Updating the BIOS through the Internet To update the BIOS through the Internet: 1. Launch the ASUS Update utility from the Windows ® desktop by clicking Start Start Start Start Start > Programs Programs Programs Programs Programs > ASUS ASUS ASUS ASUS ASUS > ASUSUpdate ASUSUpdate ASUSUpdate ASUSUpdate ASUSUpdate > ASUSUpdate ASUSUpdate ASUSUpdate ASUSUpdate ASUSUpdate . T h e ASUS Update main window appears. 2. Select Update BIOS from Update BIOS from Update BIOS from Update BIOS from Update BIOS from the Internet the Internet the Internet the Internet the Internet option from the drop-down menu, then click Next Next Next Next Next .
4-10 4-10 4-10 4-10 4-10 Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Updating the BIOS through a BIOS file Updating the BIOS through a BIOS file Updating the BIOS through a BIOS file Updating the BIOS through a BIOS file Updating the BIOS through a BIOS file To update the BIOS through a BIOS file: 1. Launch the ASUS Update utility from the Windows ® desktop by clicking Start Start Start Start Start > Programs Programs Programs Programs Programs > ASUS ASUS ASUS ASUS ASUS > ASUSUpdate ASUSUpdate ASUSUpdate ASUSUpdate ASUSUpdate > ASUSUpdate ASUSUpdate ASUSUpdate ASUSUpdate ASUSUpdate . The ASUS Update main window appears. 2. Select Update BIOS from a Update BIOS from a Update BIOS from a Update BIOS from a Update BIOS from a file file file file file option from the drop-down menu, then click Next Next Next Next Next . 4. From the FTP site, select the BIOS version that you wish to download. Click Next. 5. Follow the screen instructions to complete the update process. The ASUS Update utility is capable of updating itself through the Internet. Always update the utility to avail of all its features. 3. Locate the BIOS file from the Open Open Open Open Open window, then click Save Save Save Save Save . 4. Follow the screen instructions to complete the update process.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 4-11 4-11 4-11 4-11 4-11 4.2 BIOS setup program This motherboard supports a programmable firmware chip that you can update using the provided utility described in section “ 4.1 Managing and updating your BIOS.” Use the BIOS Setup program when you are installing a motherboard, reconfiguring your system, or prompted to “Run Setup.” This section explains how to configure your system using this utility. Even if you are not prompted to use the Setup program, you can change the configuration of your computer in the future. For example, you can enable the security password feature or change the power management settings. This requires you to reconfigure your system using the BIOS Setup program so that the computer can recognize these changes and record them in the CMOS RAM of the firmware hub. The firmware hub on the motherboard stores the Setup utility. When you start up the computer, the system provides you with the opportunity to run this program. Press <Del> during the Power-On-Self-Test (POST) to enter the Setup utility; otherwise, POST continues with its test routines. If you wish to enter Setup after POST, restart the system by pressing <Ctrl Alt Delete>, or by pressing the reset button on the system chassis. You can also restart by turning the system off and then back on. Do this last option only if the first two failed. The Setup program is designed to make it as easy to use as possible. Being a menu-driven program, it lets you scroll through the various sub-menus and make your selections from the available options using the navigation keys. • The default BIOS settings for this motherboard apply for most conditions to ensure optimum performance. If the system becomes unstable after changing any BIOS settings, load the default settings to ensure system compatibility and stability. Select the Load Load Load Load Load Setup Defaults Setup Defaults Setup Defaults Setup Defaults Setup Defaults item under the Exit Menu. See section “4.7 Exit Menu.” • The BIOS setup screens shown in this section are for reference purposes only, and may not exactly match what you see on your screen. • Visit the ASUS website (www.asus.com) to download the latest BIOS file for this motherboard.
4-12 4-12 4-12 4-12 4-12 Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup 4.2.2 4.2.2 4.2.2 4.2.2 4.2.2 Menu bar Menu bar Menu bar Menu bar Menu bar The menu bar on top of the screen has the following main items: Main Main Main Main Main For changing the basic system configuration Advanced Advanced Advanced Advanced Advanced For changing the advanced system settings Power Power Power Power Power For changing the advanced power management (APM) configuration Boot Boot Boot Boot Boot For changing the system boot configuration Exit Exit Exit Exit Exit For selecting the exit options and loading default settings 4.2.1 4.2.1 4.2.1 4.2.1 4.2.1 BIOS menu screen BIOS menu screen BIOS menu screen BIOS menu screen BIOS menu screen To select an item on the menu bar, press the right or left arrow key on the keyboard until the desired item is highlighted. Some of the navigation keys differ from one screen to another. 4.2.3 4.2.3 4.2.3 4.2.3 4.2.3 Navigation keys Navigation keys Navigation keys Navigation keys Navigation keys At the bottom right corner of a menu screen are the navigation keys for that particular menu. Use the navigation keys to select items in the menu and change the settings. System Time [16:37:21] System Date [Wed,06/01/2005] Legacy Diskette A [1.44M, 3.5 in.] Primary IDE Master [ST320410A] Primary IDE Slave [ASUS CD-S520/A] Third IDE Master [Not Detected] Third IDE Slave [Not Detected] Fourth IDE Master [Not Detected] Fourth IDE Slave [Not Detected] IDE Configuration System Information Use [ENTER], [TAB] or [SHIFT-TAB] to select a field. Use [ ] or [-] to configure the System time. Navigation keys Navigation keys Navigation keys Navigation keys Navigation keys General help General help General help General help General help Menu bar Menu bar Menu bar Menu bar Menu bar Sub-menu items Sub-menu items Sub-menu items Sub-menu items Sub-menu items Configuration fields Configuration fields Configuration fields Configuration fields Configuration fields Menu items Menu items Menu items Menu items Menu items
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 4-13 4-13 4-13 4-13 4-13 4.2.4 4.2.4 4.2.4 4.2.4 4.2.4 Menu items Menu items Menu items Menu items Menu items The highlighted item on the menu bar displays the specific items for that menu. For example, selecting Main Main Main Main Main shows the Main menu items. The other items (Advanced, Power, Boot, and Exit) on the menu bar have their respective menu items. 4.2.5 4.2.5 4.2.5 4.2.5 4.2.5 Sub-menu items Sub-menu items Sub-menu items Sub-menu items Sub-menu items A solid triangle before each item on any menu screen means that the item has a sub-menu. To display the sub-menu, select the item and press <Enter>. 4.2.6 4.2.6 4.2.6 4.2.6 4.2.6 Configuration fields Configuration fields Configuration fields Configuration fields Configuration fields These fields show the values for the menu items. If an item is user-configurable, you can change the value of the field opposite the item. You cannot select an item that is not user-configurable. A configurable field is enclosed in brackets, and is highlighted when selected. To change the value of a field, select it then press <Enter> to display a list of options. Refer to “4.2.7 Pop-up window.” 4.2.7 4.2.7 4.2.7 4.2.7 4.2.7 Pop-up window Pop-up window Pop-up window Pop-up window Pop-up window Select a menu item then press <Enter> to display a pop-up window with the configuration options for that item. 4.2.8 4.2.8 4.2.8 4.2.8 4.2.8 Scroll bar Scroll bar Scroll bar Scroll bar Scroll bar A scroll bar appears on the right side of a menu screen when there are items that do not fit on the screen. Press the Up/Down arrow keys or <Page Up> / <Page Down> keys to display the other items on the screen. 4.2.9 4.2.9 4.2.9 4.2.9 4.2.9 General help General help General help General help General help At the top right corner of the menu screen is a brief description of the selected item. Main menu items Main menu items Main menu items Main menu items Main menu items System Time [16 :3 7 :2 1 ] System Date [Wed, 06/ 01 /2005 ] Legacy Diskette A [1.44M, 3.5 in] Primary IDE Master : [ ST320410 A] Primary IDE Slave : [ ASUS CD-S520/A] Third IDE Master : [Not Detected] Third IDE Slave : [Not Detected] Fourth IDE Master : [Not Detected] Fourth IDE Slave : [Not Detected] IDE Configuration System Information Advanced PCI/PnP Settings WARNING: Setting wrong values in below sections may cause system to malfunction. Plug And Play O/S [No] PCI Latency Timer [64] Allocate IRQ to PCI VGA [Yes] Palette Snooping [Disabled] PCI IDE BusMaster [Enabled] Scroll bar Scroll bar Scroll bar Scroll bar Scroll bar Pop-up window Pop-up window Pop-up window Pop-up window Pop-up window
4-14 4-14 4-14 4-14 4-14 Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup 4.3 Main menu When you enter the BIOS Setup program, the Main menu screen appears, giving you an overview of the basic system information. 4.3.1 4.3.1 4.3.1 4.3.1 4.3.1 System Time [xx:xx:xx] System Time [xx:xx:xx] System Time [xx:xx:xx] System Time [xx:xx:xx] System Time [xx:xx:xx] Sets the system time. 4.3.2 4.3.2 4.3.2 4.3.2 4.3.2 System Date [Day xx/xx/xxxx] System Date [Day xx/xx/xxxx] System Date [Day xx/xx/xxxx] System Date [Day xx/xx/xxxx] System Date [Day xx/xx/xxxx] Sets the system date. 4.3.3 4.3.3 4.3.3 4.3.3 4.3.3 Legacy Diskette A [1.44M, 3.5 in.] Legacy Diskette A [1.44M, 3.5 in.] Legacy Diskette A [1.44M, 3.5 in.] Legacy Diskette A [1.44M, 3.5 in.] Legacy Diskette A [1.44M, 3.5 in.] Sets the type of floppy drive installed. Configuration options: [Disabled] [360K, 5.25 in.] [1.2M , 5.25 in.] [720K , 3.5 in.] [1.44M, 3.5 in.] [2.88M, 3.5 in.] Refer to section “4.2.1 BIOS menu screen” for information on the menu screen items and how to navigate through them. Use [ENTER], [TAB] or [SHIFT-TAB] to select a field. Use [ ] or [-] to configure the System time. System Time [16:37:21] System Date [Mon,10/02/2004] Legacy Diskette A [1.44M, 3.5 in.] Primary IDE Master : [ST320410A] Primary IDE Slave : [ASUS CD-S520/A] Third IDE Master : [Not Detected] Third IDE Slave : [Not Detected] Fourth IDE Master : [Not Detected] Fourth IDE Slave : [Not Detected] IDE Configuration System Information
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 4-15 4-15 4-15 4-15 4-15 4.3.4 4.3.4 4.3.4 4.3.4 4.3.4 Primary, Third, and Fourth IDE Master/Slave Primary, Third, and Fourth IDE Master/Slave Primary, Third, and Fourth IDE Master/Slave Primary, Third, and Fourth IDE Master/Slave Primary, Third, and Fourth IDE Master/Slave While entering Setup, the BIOS automatically detects the presence of IDE devices. There is a separate sub-menu for each IDE device. Select a device item then press <Enter> to display the IDE device information. Primary IDE Master Select the type of device connected to the system. Device : Hard Disk Vendor : ST320410A Size : 20.0GB LBA Mode : Supported Block Mode : 16 Sectors PIO Mode : 4 Async DMA : MultiWord DMA-2 Ultra DMA : Ultra DMA-5 SMART Monitoring : Supported Type [Auto] LBA/Large Mode [Auto] Block(Multi-sector Transfer) M [Auto] PIO Mode [Auto] DMA Mode [Auto] SMART Monitoring [Auto] 32Bit Data Transfer [Disabled] The BIOS automatically detects the values opposite the dimmed items (Device, Vendor, Size, LBA Mode, Block Mode, PIO Mode, Async DMA, Ultra DMA, and SMART monitoring). These values are not user-configurable. These items show N/A if no IDE device is installed in the system. Type [Auto] Type [Auto] Type [Auto] Type [Auto] Type [Auto] Selects the type of IDE drive. Setting to Auto allows automatic selection of the appropriate IDE device type. Select CDROM if you are specifically configuring a CD-ROM drive. Select ARMD (ATAPI Removable Media Device) if your device is either a ZIP, LS-120, or MO drive. Configuration options: [Not Installed] [Auto] [CDROM] [ARMD] LBA/Large Mode [Auto] LBA/Large Mode [Auto] LBA/Large Mode [Auto] LBA/Large Mode [Auto] LBA/Large Mode [Auto] Enables or disables the LBA mode. Setting to Auto enables the LBA mode if the device supports this mode, and if the device was not previously formatted with LBA mode disabled. Configuration options: [Disabled] [Auto] Block (Multi-sector Transfer) [Auto] Block (Multi-sector Transfer) [Auto] Block (Multi-sector Transfer) [Auto] Block (Multi-sector Transfer) [Auto] Block (Multi-sector Transfer) [Auto] Enables or disables data multi-sectors transfers. When set to Auto, the data transfer from and to the device occurs multiple sectors at a time if the device supports multi-sector transfer feature. When set to [Disabled], the data transfer from and to the device occurs one sector at a time. Configuration options: [Disabled] [Auto]
4-16 4-16 4-16 4-16 4-16 Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup PIO Mode [Auto] PIO Mode [Auto] PIO Mode [Auto] PIO Mode [Auto] PIO Mode [Auto] Selects the PIO mode. Configuration options: [Auto] [0] [1] [2] [3] [4] DMA Mode [Auto] DMA Mode [Auto] DMA Mode [Auto] DMA Mode [Auto] DMA Mode [Auto] Allows the BIOS to automatically select the DMA mode. Configuration option: [Auto] SMART Monitoring [Auto] SMART Monitoring [Auto] SMART Monitoring [Auto] SMART Monitoring [Auto] SMART Monitoring [Auto] Sets the Smart Monitoring, Analysis, and Reporting Technology. Configuration options: [Auto] [Disabled] [Enabled] 32Bit Data Transfer [Disabled] 32Bit Data Transfer [Disabled] 32Bit Data Transfer [Disabled] 32Bit Data Transfer [Disabled] 32Bit Data Transfer [Disabled] Enables or disables 32-bit data transfer. Configuration options: [Disabled] [Enabled] 4.3.5 4.3.5 4.3.5 4.3.5 4.3.5 IDE Configuration IDE Configuration IDE Configuration IDE Configuration IDE Configuration The items in this menu allow you to set or change the configurations for the IDE devices installed in the system. Select an item then press <Enter> if you want to configure the item. IDE Configuration Configure SATA As [Standard IDE] Onboard IDE Operate Mode [Enhanced Mode] Enhanced Mode Support On [S-ATA] IDE Detect Time Out (Sec) [35] Configure SATA As [Standard IDE] Configure SATA As [Standard IDE] Configure SATA As [Standard IDE] Configure SATA As [Standard IDE] Configure SATA As [Standard IDE] Sets the Serial ATA configuration. When set in Advanced Host Controller Interface (AHCI) or RAID mode the SATA controller is set to Native mode. Configuration options: [Standard IDE] [AHCI] [RAID] Onboard IDE Operate Mode [Enhanced Mode] Onboard IDE Operate Mode [Enhanced Mode] Onboard IDE Operate Mode [Enhanced Mode] Onboard IDE Operate Mode [Enhanced Mode] Onboard IDE Operate Mode [Enhanced Mode] Allows selection of the IDE operation mode depending on the operating system (OS) that you installed. Set to Enhanced Mode if you are using native OS, such as Windows ® 2000/XP. Configuration options: [Disabled] [Compatible Mode] [Enhanced Mode] When in AHCI/RAID mode, SATA controller is forced to Native mode.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 4-17 4-17 4-17 4-17 4-17 If the Onboard IDE Operate Mode Onboard IDE Operate Mode Onboard IDE Operate Mode Onboard IDE Operate Mode Onboard IDE Operate Mode i s set to [Compatible], you can only use the SATA2, SATA4, and P-ATA connectors. Enhanced Mode Support On [S-ATA] The default setting SATA allows you to use native OS on Serial ATA and Parallel ATA ports. We recommend that you do not change the default setting for better OS compatibility. In this setting, you may use legacy OS on the Parallel ATA ports only if only if only if only if only if you did not install any Serial ATA device. The S-ATA P-ATA and P-ATA options are for advanced users only. If you set to any of these options and encounter problems, revert to the default setting SATA SATA SATA SATA S A T A. Configuration options: [S-ATA P-ATA] [S-ATA] [P-ATA] The Onboard IDE Operate Mode Onboard IDE Operate Mode Onboard IDE Operate Mode Onboard IDE Operate Mode Onboard IDE Operate Mode and its submenu items appear only when the Configure SATA As Configure SATA As Configure SATA As Configure SATA As Configure SATA As item is set to Standard IDE. Onboard Serial-ATA BOOTROM [Disabled] Enables or disables the onboard Serial ATA boot ROM. Configuration options: [Disabled] [Enabled] The Onboard Serial-ATA BOOTROM Onboard Serial-ATA BOOTROM Onboard Serial-ATA BOOTROM Onboard Serial-ATA BOOTROM Onboard Serial-ATA BOOTROM item appears only when the Configure SATA As Configure SATA As Configure SATA As Configure SATA As Configure SATA As item is set to RAID. ALPE and ASP [Disabled] Enables or disables the ALPE and ASP. Configuration options: [Disabled] [Enabled] Stagger Spinup Support [Disabled] Stagger Spinup Support [Disabled] Stagger Spinup Support [Disabled] Stagger Spinup Support [Disabled] Stagger Spinup Support [Disabled] Enables or disables the stagger spinup support. Configuration options: [Disabled] [Enabled] AHCI Port 3 Interlock Switch [Disabled] AHCI Port 3 Interlock Switch [Disabled] AHCI Port 3 Interlock Switch [Disabled] AHCI Port 3 Interlock Switch [Disabled] AHCI Port 3 Interlock Switch [Disabled] Enables or disables the Advanced Host Controller Interface (AHCI) Port 3 interlock switch. Configuration options: [Disabled] [Enabled] The ALPE and ASP ALPE and ASP ALPE and ASP ALPE and ASP ALPE and ASP item appears only when the Configure SATA Configure SATA Configure SATA Configure SATA Configure SATA As As As As A s item is set to AHCI. IDE Detect Time Out [35] IDE Detect Time Out [35] IDE Detect Time Out [35] IDE Detect Time Out [35] IDE Detect Time Out [35] Selects the time out value for detecting ATA/ATAPI devices. Configuration options: [0] [5] [10] [15] [20] [25] [30] [35]
4-18 4-18 4-18 4-18 4-18 Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup 4.3.6 4.3.6 4.3.6 4.3.6 4.3.6 System Information System Information System Information System Information System Information This menu gives you an overview of the general system specifications. The BIOS automatically detects the items in this menu. AMI BIOS AMI BIOS AMI BIOS AMI BIOS AMI BIOS Displays the auto-detected BIOS information. Processor Processor Processor Processor Processor Displays the auto-detected CPU specification. System Memory System Memory System Memory System Memory System Memory Displays the auto-detected system memory. AMIBIOS Version : 08.00.11 Build Date : 03/21/05 Processor Type : Genuine Intel(R) CPU 3.20 GHz Speed : 3200 MHz Count : 1 System Memory Size : 512 MB
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 4-19 4-19 4-19 4-19 4-19 4.4 Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices. Take caution when changing the settings of the Advanced menu items. Incorrect field values can cause the system to malfunction. USB Configuration MPS Configuration Remote Access Configuration CPU Configuration Chipset Onboard Devices Configuration PCI PnP USB settings. The Module Version Module Version Module Version Module Version Module Version and USB Devices Enabled USB Devices Enabled USB Devices Enabled USB Devices Enabled USB Devices Enabled items show the auto-detected values. If no USB device is detected, the item shows None None None None None . 4.4.1 4.4.1 4.4.1 4.4.1 4.4.1 USB Configuration USB Configuration USB Configuration USB Configuration USB Configuration The items in this menu allow you to change the USB-related features. Select an item then press <Enter> to display the configuration options. USB Configuration Module Version - 2.24.0-F.4 USB Devices Enabled: None USB Function [8 USB Ports] Legacy USB Support [Auto] USB 2.0 Controller [Enabled] USB 2.0 Controller Mode [HiSpeed] BIOS EHCI Hand-Off [Enabled] Enables USB host controllers.
4-20 4-20 4-20 4-20 4-20 Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup USB Function [8 USB Ports] USB Function [8 USB Ports] USB Function [8 USB Ports] USB Function [8 USB Ports] USB Function [8 USB Ports] Allows you to disable or set the USB host controllers. Configuration options: [Disabled] [2 USB Ports] [4 USB Ports] [6 USB Ports] [8 USB Ports] Legacy USB Support [Enabled] Legacy USB Support [Enabled] Legacy USB Support [Enabled] Legacy USB Support [Enabled] Legacy USB Support [Enabled] Allows you to enable or disable support for USB devices on legacy operating systems (OS). Setting to Auto allows the system to detect the presence of USB devices at startup. If detected, the USB controller legacy mode is enabled. If no USB device is detected, the legacy USB support is disabled. Configuration options: [Disabled] [Enabled] [Auto] USB 2.0 Controller [Enabled] USB 2.0 Controller [Enabled] USB 2.0 Controller [Enabled] USB 2.0 Controller [Enabled] USB 2.0 Controller [Enabled] Allows you to enable or disable the USB 2.0 controller. Configuration options: [Enabled] [Disabled] USB 2.0 Controller Mode [HiSpeed] USB 2.0 Controller Mode [HiSpeed] USB 2.0 Controller Mode [HiSpeed] USB 2.0 Controller Mode [HiSpeed] USB 2.0 Controller Mode [HiSpeed] Allows you to set the USB 2.0 controller mode to HiSpeed (480 Mbps) or FullSpeed (12 Mbps). Configuration options: [FullSpeed ] [HiSpeed ] BIOS EHCI Hand-Off [Enabled] BIOS EHCI Hand-Off [Enabled] BIOS EHCI Hand-Off [Enabled] BIOS EHCI Hand-Off [Enabled] BIOS EHCI Hand-Off [Enabled] This is a workaround for operating systems without EHCI hand-off support. The ownership should be claimed by the EHCI driver. Configuration options: [Disabled] [Enabled] 4.4.2 4.4.2 4.4.2 4.4.2 4.4.2 MPS Configuration MPS Configuration MPS Configuration MPS Configuration MPS Configuration This menu allows you to configure the Multi-Processor table. Select an item then press <Enter> to display the configuration options. MPS Configuration MPS Revision [1.4] MPS Revision [1.4] MPS Revision [1.4] MPS Revision [1.4] MPS Revision [1.4] MPS Revision [1.4] Allows you to choose the MPS revision. Configuration options: [1.1] [1.4] Select MPS Revision.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 4-21 4-21 4-21 4-21 4-21 4.4.3 4.4.3 4.4.3 4.4.3 4.4.3 Remote Access Configuration Remote Access Configuration Remote Access Configuration Remote Access Configuration Remote Access Configuration The items in this menu allow you to configure the Remote Access features. Select an item then press <Enter> to display the configuration options. Configure Remote Access type and parameters Remote Access [Disabled] Select Remote Access type. Remote Access [Disabled] Remote Access [Disabled] Remote Access [Disabled] Remote Access [Disabled] Remote Access [Disabled] Enables or disables the remote access feature. Configuration options: [Disabled] [Enabled] The succeeding items appear when the item Remote Access Remote Access Remote Access Remote Access Remote Access i s set to [Enabled]. Serial port number [COM1] Serial port number [COM1] Serial port number [COM1] Serial port number [COM1] Serial port number [COM1] Sets the serial port for console redirection. Make sure the selected port is enabled. Configuration options: [COM1] [COM2] Base Address, IRQ [3F8h, 4] Base Address, IRQ [3F8h, 4] Base Address, IRQ [3F8h, 4] Base Address, IRQ [3F8h, 4] Base Address, IRQ [3F8h, 4] Sets the base address and IRQ assignment of the selected serial port . This item is auto-detected and is not user-configurable. Serial Port Mode [115200, 8,n,1] Serial Port Mode [115200, 8,n,1] Serial Port Mode [115200, 8,n,1] Serial Port Mode [115200, 8,n,1] Serial Port Mode [115200, 8,n,1] Allows you to select the serial port mode settings. Configuration options: [115200 8,n,1] [57600 8,n,1] [38400 8,n,1] [19200 8,n,1] [09600 8,n,1] Flow Control [None] Flow Control [None] Flow Control [None] Flow Control [None] Flow Control [None] Allows you to select the flow control for console redirection. Configuration options: [None [Hardware] [Software] Redirection after BIOS POST [Always] Redirection after BIOS POST [Always] Redirection after BIOS POST [Always] Redirection after BIOS POST [Always] Redirection after BIOS POST [Always] Sets the redirection mode after the BIOS Power-On-Self-Test (POST). Some operating systems may not work when this item is set to [Always]. Configuration options: [Disabled] [Boot Loader] [Always] Terminal Type Terminal Type Terminal Type Terminal Type Terminal Type [ANSI] [ANSI] [ANSI] [ANSI] [ANSI] Allows you to select the target terminal type. Configuration options: [ANSI] [VT100] [VT-UTF8]
4-22 4-22 4-22 4-22 4-22 Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup 4.4.4 4.4.4 4.4.4 4.4.4 4.4.4 CPU Configuration CPU Configuration CPU Configuration CPU Configuration CPU Configuration The items in this menu show the CPU-related information that the BIOS automatically detects. Configure advanced CPU Settings Manufacturer : Intel Brand String : Genuine Intel (R) CPU 3.20GHz Frequency : 3200 MHz FSB Speed : 800 MHz Cache L1 : 16 KB Cache L2 : 1024 KB Cache L3 : 0 KB Ratio Status: Unlocked (Max:16, Min:14) Ratio Actual Value : 14 Max CPUID Value Limit: [Disabled] Execute Disable Function [Disabled] Enhanced C1 Control [Auto] Hardware Prefetcher: [Enabled] Adjacent Cache Line Prefetch: [Enabled] CPU Internal Thermal Control [Auto] Hyper Threading Technology [Enabled] Sets the ratio between CPU Core Clock and the FSB Frequency. NOTE: If an invalid ratio is set in CMOS then actual and setpoint values may differ. Max CPUID Value Limit [Disabled] Max CPUID Value Limit [Disabled] Max CPUID Value Limit [Disabled] Max CPUID Value Limit [Disabled] Max CPUID Value Limit [Disabled] Enable this item to boot legacy operating systems that cannot support CPUs with extended CPUID functions. Configuration options: [Disabled] [Enabled] Execute Disable Function [Disabled] Execute Disable Function [Disabled] Execute Disable Function [Disabled] Execute Disable Function [Disabled] Execute Disable Function [Disabled] Allows you to enable or disable the execute disable function. Configuration options: [Disabled] [Enabled] Enhanced C1 Control [Auto] Enhanced C1 Control [Auto] Enhanced C1 Control [Auto] Enhanced C1 Control [Auto] Enhanced C1 Control [Auto] When set to [Auto], the BIOS will automatically check the CPU’s capability to enable the C1E support. In C1E mode, the CPU power consumption is lower when idle. Configuration options: [Auto] [Disabled] Hardware Prefetcher [Enabled] Hardware Prefetcher [Enabled] Hardware Prefetcher [Enabled] Hardware Prefetcher [Enabled] Hardware Prefetcher [Enabled] Allows you to enable or disable the hardware prefetcher feature. Configuration options: [Disabled] [Enabled] VT-UTF8 Combo Key Support [Enabled] VT-UTF8 Combo Key Support [Enabled] VT-UTF8 Combo Key Support [Enabled] VT-UTF8 Combo Key Support [Enabled] VT-UTF8 Combo Key Support [Enabled] Enables or disables the VT-UTF8 combo key support for ANSI or VT100 terminals. Configuration options: [Disabled] [Enabled]
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 4-23 4-23 4-23 4-23 4-23 Adjacent Cache Line Prefetch [Enabled] Adjacent Cache Line Prefetch [Enabled] Adjacent Cache Line Prefetch [Enabled] Adjacent Cache Line Prefetch [Enabled] Adjacent Cache Line Prefetch [Enabled] Allows you to enable or disable the adjacent cache line prefetch feature. Configuration options: [Disabled] [Enabled] CPU Internal Thermal Control [Auto] CPU Internal Thermal Control [Auto] CPU Internal Thermal Control [Auto] CPU Internal Thermal Control [Auto] CPU Internal Thermal Control [Auto] Disables or sets the CPU internal thermal control. Configuration options: [Auto] [Disabled] The following item appears only when you installed an Intel ® Pentium ® 4 processor that supports Hyper Threading Technology. Hyper Threading Technology [Enabled] Hyper Threading Technology [Enabled] Hyper Threading Technology [Enabled] Hyper Threading Technology [Enabled] Hyper Threading Technology [Enabled] Allows you to enable or disable the processor Hyper Threading Technology. Configuration options: [Disabled] [Enabled] 4.4.5 4.4.5 4.4.5 4.4.5 4.4.5 Chipset Chipset Chipset Chipset Chipset The Chipset menu allows you to change the advanced chipset settings. Select an item then press <Enter> to display the sub-menu. Manual DRAM Frequency Setting or Auto by SPD. Advanced Chipset Settings DRAM Frequency [Auto] Configure DRAM Timing by SPD [Enabled] Onboard LAN Boot ROM [Disabled] PEG Port Configuration PEG Port [Enabled] PEG Port VC1 Map [TC7] PEG Force x1 [Disabled] Memory Remap Feature [Disabled] DRAM Frequency [Auto] DRAM Frequency [Auto] DRAM Frequency [Auto] DRAM Frequency [Auto] DRAM Frequency [Auto] Allows you to manually set the DRAM frequency. Setting to [Auto] allows the BIOS to automatically set the DRAM frequency by Serial Presence Detect (SPD). Configuration options: [Auto] [533 MHz] [667 MHz]
4-24 4-24 4-24 4-24 4-24 Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Configure DRAM Timing by SPD [Enabled] Configure DRAM Timing by SPD [Enabled] Configure DRAM Timing by SPD [Enabled] Configure DRAM Timing by SPD [Enabled] Configure DRAM Timing by SPD [Enabled] When this item is enabled, the DRAM timing parameters are set according to the DRAM SPD (Serial Presence Detect). When disabled, you can manually set the DRAM timing parameters through the DRAM sub-items. Configuration options: [Disabled] [Enabled] The following sub-items appear when this item is Disabled. DRAM CAS# Latency [5 Clocks] Controls the latency between the SDRAM read command and the time the data actually becomes available. Configuration options: [5 Clocks] [4 Clocks] [3 Clocks] [6 Clocks] DRAM RAS# Precharge [4 Clocks] Controls the idle clocks after issuing a precharge command to the DDR SDRAM. Configuration options: [2 Clocks] [3 Clocks] [4 Clocks] [5 Clocks] DRAM RAS# to CAS# Delay [4 Clocks] Controls the latency between the DDR SDRAM active command and the read/write command. Configuration options: [2 Clocks] [3 Clocks] [4 Clocks] [5 Clocks] DRAM RAS# Activate to Precharge Delay [15 Clocks] Configuration options: [1 Clock] ~ [15 Clocks] DRAM Write Recovery Time [4 Clocks] Sets the DRAM write recovery time. Configuration options: [2 Clocks] [3 Clocks] [4 Clocks] [5 Clocks] Onboard LAN Boot ROM [Disabled] Onboard LAN Boot ROM [Disabled] Onboard LAN Boot ROM [Disabled] Onboard LAN Boot ROM [Disabled] Onboard LAN Boot ROM [Disabled] Allows you to enable or disable the onboard LAN boot ROM. Configuration options: [Disabled] [Enabled] PEG Port [Enabled] PEG Port [Enabled] PEG Port [Enabled] PEG Port [Enabled] PEG Port [Enabled] Allows you to enable or disable the PCI Express Graphics port. Configuration options: [Disabled] [Enabled] PEG Port VC1 Map [TC7] Allows you to disable or set the PCI Express Graphics port VC1 map. Configuration options: [Disabled] [TC1] ~ [TC7] PEG Force x1 [Disabled] Configuration options: [Disabled] [Enabled] Memory Remap Feature [Disabled] Memory Remap Feature [Disabled] Memory Remap Feature [Disabled] Memory Remap Feature [Disabled] Memory Remap Feature [Disabled] Allows you to enable or disable the memory remap feature. Configuration options: [Disabled] [Enabled]
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 4-25 4-25 4-25 4-25 4-25 4.4.6 4.4.6 4.4.6 4.4.6 4.4.6 Onboard Devices Configuration Onboard Devices Configuration Onboard Devices Configuration Onboard Devices Configuration Onboard Devices Configuration Configure Win627EHF Super IO Chipset Serial Port1 Address [3F8/IRQ4] Serial Port2 Address [2F8/IRQ3] Serial Port2 Mode [Normal] Parallel Port Address [378] Parallel Port Mode [ECP] ECP Mode DMA Channel [DMA3] Parallel Port IRQ [IRQ7] Serial Port1 Address [3F8/IRQ4] Serial Port1 Address [3F8/IRQ4] Serial Port1 Address [3F8/IRQ4] Serial Port1 Address [3F8/IRQ4] Serial Port1 Address [3F8/IRQ4] Allows you to select the Serial Port1 base address. Configuration options: [Disabled] [3F8/IRQ4] [3E8/IRQ4] [2E8/IRQ3] Serial Port2 Address [2F8/IRQ3] Serial Port2 Address [2F8/IRQ3] Serial Port2 Address [2F8/IRQ3] Serial Port2 Address [2F8/IRQ3] Serial Port2 Address [2F8/IRQ3] Allows you to select the Serial Port1 base address. Configuration options: [Disabled] [2F8/IRQ3] [3E8/IRQ4] [2E8/IRQ3] Serial Port2 Mode [Normal] Allows the BIOS to select the Serial Port 2 mode. Configuration options: [Normal] [IrDA] [ASK IR] Parallel Port Address [378] Parallel Port Address [378] Parallel Port Address [378] Parallel Port Address [378] Parallel Port Address [378] Allows you to select the Parallel Port base addresses. Configuration options: [Disabled] [378] [278] [3BC] Parallel Port Mode [ECP] Parallel Port Mode [ECP] Parallel Port Mode [ECP] Parallel Port Mode [ECP] Parallel Port Mode [ECP] Allows you to select the Parallel Port mode. Configuration options: [Normal] [Bi-directional] [EPP] [ECP] ECP Mode DMA Channel [DMA3] ECP Mode DMA Channel [DMA3] ECP Mode DMA Channel [DMA3] ECP Mode DMA Channel [DMA3] ECP Mode DMA Channel [DMA3] Appears only when the Parallel Port Mode is set to [ECP]. This item allows you to set the Parallel Port ECP DMA. Configuration options: [DMA0] [DMA1] [DMA3] EPP Version [1.9] EPP Version [1.9] EPP Version [1.9] EPP Version [1.9] EPP Version [1.9] Allows selection of the Parallel Port EPP version. This item appears only when the Parallel Port Mode Parallel Port Mode Parallel Port Mode Parallel Port Mode Parallel Port Mode i s set to EPP EPP EPP EPP EPP . Configuration options: [1.9] [1.7] Parallel Port IRQ [IRQ7] Allows selection of the Parallel Port IRQ. Configuration options: [IRQ5] [IRQ7] Enable or disable the Azalia controller.
4-26 4-26 4-26 4-26 4-26 Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup 4.4.7 4.4.7 4.4.7 4.4.7 4.4.7 PCI PnP PCI PnP PCI PnP PCI PnP PCI PnP The PCI PnP menu items allow you to change the advanced settings for PCI/PnP devices. The menu includes setting IRQ and DMA channel resources for either PCI/PnP or legacy ISA devices, and setting the memory size block for legacy ISA devices. Take caution when changing the settings of the PCI PnP menu items. Incorrect field values can cause the system to malfunction. Advanced PCI/PnP Settings WARNING: Setting wrong values in below sections may cause system to malfunction. Plug And Play O/S [No] PCI Latency Timer [64] Allocate IRQ to PCI VGA [Yes] Palette Snooping [Disabled] IRQ-3 assigned to [PCI Device] IRQ-4 assigned to [PCI Device] IRQ-5 assigned to [PCI Device] IRQ-7 assigned to [PCI Device] IRQ-9 assigned to [PCI Device] IRQ-10 assigned to [PCI Device] IRQ-11 assigned to [PCI Device] IRQ-14 assigned to [PCI Device] IRQ-15 assigned to [PCI Device] Plug and Play O/S [No] Plug and Play O/S [No] Plug and Play O/S [No] Plug and Play O/S [No] Plug and Play O/S [No] When set to [No], BIOS configures all the devices in the system. When set to [Yes] and if you install a Plug and Play operating system, the operating system configures the Plug and Play devices not required for boot. Configuration options: [No] [Yes] PCI Latency Timer [64] PCI Latency Timer [64] PCI Latency Timer [64] PCI Latency Timer [64] PCI Latency Timer [64] Allows you to select the value in units of PCI clocks for the PCI device latency timer register. Configuration options: [32] [64] [96] [128] [160] [192] [224] [248] Allocate IRQ to PCI VGA [Yes] Allocate IRQ to PCI VGA [Yes] Allocate IRQ to PCI VGA [Yes] Allocate IRQ to PCI VGA [Yes] Allocate IRQ to PCI VGA [Yes] When set to [Yes], BIOS assigns an IRQ to PCI VGA card if the card requests for an IRQ. When set to [No], BIOS does not assign an IRQ to the PCI VGA card even if requested. Configuration options: [Yes] [No] Palette Snooping [Disabled] Palette Snooping [Disabled] Palette Snooping [Disabled] Palette Snooping [Disabled] Palette Snooping [Disabled] When set to [Enabled], the palette snooping feature informs the PCI devices that an ISA graphics device is installed in the system so that the latter can function correctly. Configuration options: [Disabled] [Enabled] No: Lets the BIOS configure all the devices in the system. Yes: Lets the operating system configure Plug and Play (PnP) devices not required for boot if your system has a Plug and Play operating system.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 4-27 4-27 4-27 4-27 4-27 4.5 Power menu The Power menu items allow you to change the settings for the ACPI and Advanced Power Management (APM). Select an item then press <Enter> to display the configuration options. 4.5.1 4.5.1 4.5.1 4.5.1 4.5.1 ACPI APIC Support [Enabled] ACPI APIC Support [Enabled] ACPI APIC Support [Enabled] ACPI APIC Support [Enabled] ACPI APIC Support [Enabled] Allows you to enable or disable the Advanced Configuration and Power Interface (ACPI) support in the Advanced Programmable Interrupt Controller (APIC). When set to Enabled, the ACPI APIC table pointer is included in the RSDT pointer list. Configuration options: [Disabled] [Enabled] ACPI APIC Support [Enabled] APM Configuration Hardware Monitor Select the ACPI state used for System Suspend. IRQ-xx assigned to [PCI Device] IRQ-xx assigned to [PCI Device] IRQ-xx assigned to [PCI Device] IRQ-xx assigned to [PCI Device] IRQ-xx assigned to [PCI Device] When set to [PCI Device], the specific IRQ is free for use of PCI/PnP devices. When set to [Reserved], the IRQ is reserved for legacy ISA devices. Configuration options: [PCI Device] [Reserved]
4-28 4-28 4-28 4-28 4-28 Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup 4.5.2 4.5.2 4.5.2 4.5.2 4.5.2 APM Configuration APM Configuration APM Configuration APM Configuration APM Configuration APM Configuration Restore on AC Power Loss [Last State] Resume On RTC Alarm [Disabled] Power On By PS/2 Keyboard [Disabled] Power On By PS/2 Mouse [Disabled] Power On Ring [Disabled] Power On By PCI Devices [Disabled] Keyboard Wakeup Password : Not Installed Restore on AC Power Loss [Last State] Restore on AC Power Loss [Last State] Restore on AC Power Loss [Last State] Restore on AC Power Loss [Last State] Restore on AC Power Loss [Last State] When set to Power Off, the system goes into off state after an AC power loss. When set to Power On, the system goes on after an AC power loss. When set to Last State, the system goes into either off or on state, whatever the system state was before the AC power loss. Configuration options: [Power Off] [Power On] [Last State] Resume On RTC Alarm [Disabled] Resume On RTC Alarm [Disabled] Resume On RTC Alarm [Disabled] Resume On RTC Alarm [Disabled] Resume On RTC Alarm [Disabled] Allows you to enable or disable RTC to generate a wake event. When this item is set to Enabled, the items RTC Alarm Date, RTC Alarm Hour, RTC Alarm Minute, and RTC Alarm Second appear with set values. Configuration options: [Disabled] [Enabled] Power On By PS/2 Keyboard [Disabled] Power On By PS/2 Keyboard [Disabled] Power On By PS/2 Keyboard [Disabled] Power On By PS/2 Keyboard [Disabled] Power On By PS/2 Keyboard [Disabled] Allows you to use specific keys on the keyboard to turn on the system. This feature requires an ATX power supply that provides at least 1A on the 5VSB lead. Configuration options: [Disabled] [Enabled] Power On By PS/2 Mouse [Disabled] Power On By PS/2 Mouse [Disabled] Power On By PS/2 Mouse [Disabled] Power On By PS/2 Mouse [Disabled] Power On By PS/2 Mouse [Disabled] When set to [Enabled], this parameter allows you to use the PS/2 mouse to turn on the system. This feature requires an ATX power supply that provides at least 1A on the 5VSB lead. Configuration options: [Disabled] [Enabled] Power On Ring [Disabled] Power On Ring [Disabled] Power On Ring [Disabled] Power On Ring [Disabled] Power On Ring [Disabled] Allows you to enable or disable the RI to generate a wake event. Configuration options: [Disabled] [Enabled] Options Power Off Power On Last State
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 4-29 4-29 4-29 4-29 4-29 Power On By PCI Devices [Disabled] Power On By PCI Devices [Disabled] Power On By PCI Devices [Disabled] Power On By PCI Devices [Disabled] Power On By PCI Devices [Disabled] When set to [Enabled], this parameter allows you to turn on the system through a PCI LAN or modem card. This feature requires an ATX power supply that provides at least 1A on the 5VSB lead. Configuration options: [Disabled] [Enabled] Keyboard Wakeup Password Keyboard Wakeup Password Keyboard Wakeup Password Keyboard Wakeup Password Keyboard Wakeup Password This item appears only when the Power On By PS/2 Keyboard is set to Enabled. Select this item to set or change the keyboard wakeup password. The Keyboard Wakeup Password Keyboard Wakeup Password Keyboard Wakeup Password Keyboard Wakeup Password Keyboard Wakeup Password item that appears below shows the default Not Installed Not Installed Not Installed Not Installed Not Installed . After you have set a password, this item shows Installed Installed Installed Installed Installed . 4.5.3 4.5.3 4.5.3 4.5.3 4.5.3 Hardware Monitor Hardware Monitor Hardware Monitor Hardware Monitor Hardware Monitor Hardware Monitor CPU Temperature [51ºC/122.5ºF] MB Temperature [41ºC/105.5ºF] CPU1 Fan Speed [3813 RPM] CPU2 Fan Speed [N/A] Front Fan1 Speed [N/A] Front Fan2 Speed [N/A] Rear Fan1 Speed [N/A] Rear Fan2 Speed [N/A] Smart Fan Control [Disabled] VCORE1 Voltage [ 1.320V] 3.3V Voltage [ 3.345V] 5V Voltage [ 5.094V] 5VSB Voltage [ 4.824V] VBAT Voltage [3.040V] 12V Voltage [11.880V] CPU1 Temperature CPU Temperature [xxxºC/xxxºF] CPU Temperature [xxxºC/xxxºF] CPU Temperature [xxxºC/xxxºF] CPU Temperature [xxxºC/xxxºF] CPU Temperature [xxxºC/xxxºF] MB Temperature [xxxºC/xxxºF] MB Temperature [xxxºC/xxxºF] MB Temperature [xxxºC/xxxºF] MB Temperature [xxxºC/xxxºF] MB Temperature [xxxºC/xxxºF] The onboard hardware monitor automatically detects and displays the motherboard, CPU, and ambient temperatures. Select Ignored if you do not wish to display the detected temperatures.
4-30 4-30 4-30 4-30 4-30 Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup CPU Fan 1/2 Speed [xxxxRPM] or [N/A] CPU Fan 1/2 Speed [xxxxRPM] or [N/A] CPU Fan 1/2 Speed [xxxxRPM] or [N/A] CPU Fan 1/2 Speed [xxxxRPM] or [N/A] CPU Fan 1/2 Speed [xxxxRPM] or [N/A] Front Fan1/2 Speed [xxxxRPM] or [N/A] Front Fan1/2 Speed [xxxxRPM] or [N/A] Front Fan1/2 Speed [xxxxRPM] or [N/A] Front Fan1/2 Speed [xxxxRPM] or [N/A] Front Fan1/2 Speed [xxxxRPM] or [N/A] Rear Fan1/2 Speed [xxxxRPM] or [N/A] Rear Fan1/2 Speed [xxxxRPM] or [N/A] Rear Fan1/2 Speed [xxxxRPM] or [N/A] Rear Fan1/2 Speed [xxxxRPM] or [N/A] Rear Fan1/2 Speed [xxxxRPM] or [N/A] The onboard hardware monitor automatically detects and displays the CPU fan speed in rotations per minute (RPM). If the fan is not connected to the motherboard, the field shows N/A. Smart Fan Control [Disabled] Smart Fan Control [Disabled] Smart Fan Control [Disabled] Smart Fan Control [Disabled] Smart Fan Control [Disabled] Allows you to enable or disable the ASUS Smart Fan feature that smartly adjusts the fan speeds for more efficient system operation. Configuration options: [Disabled] [Enabled] When Smart Fan Control Smart Fan Control Smart Fan Control Smart Fan Control Smart Fan Control item is set to [Enabled], the CPU CPU CPU CPU CPU Temperature Temperature Temperature Temperature Temperature item appears. CPU Temperature [xxx] CPU Temperature [xxx] CPU Temperature [xxx] CPU Temperature [xxx] CPU Temperature [xxx] Allows you to set the temperature threshold when the CPU fan speed is increased. If the CPU/MB temperature is above your setting, the CPU fan runs at its maximum speed. If the CPU/MB temperature is below your setting, the CPU fan runs at a lower speed. To set, use the <-> or < > key. Configuration options: [Disabled] [Enabled] VCORE1 Voltage, 3.3V Voltage, 5V Voltage, 5VSB VCORE1 Voltage, 3.3V Voltage, 5V Voltage, 5VSB VCORE1 Voltage, 3.3V Voltage, 5V Voltage, 5VSB VCORE1 Voltage, 3.3V Voltage, 5V Voltage, 5VSB VCORE1 Voltage, 3.3V Voltage, 5V Voltage, 5VSB Voltage, VBAT Voltage, 12V Voltage Voltage, VBAT Voltage, 12V Voltage Voltage, VBAT Voltage, 12V Voltage Voltage, VBAT Voltage, 12V Voltage Voltage, VBAT Voltage, 12V Voltage The onboard hardware monitor automatically detects the voltage output through the onboard voltage regulators.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 4-31 4-31 4-31 4-31 4-31 Select Screen Select Item Enter Go to Sub-screen F1 General Help F10 Save and Exit ESC Exit 4.6 Boot menu The Boot menu items allow you to change the system boot options. Select an item then press <Enter> to display the sub-menu. Boot Settings Boot Device Priority Boot Settings Configuration Security 4.6.1 4.6.1 4.6.1 4.6.1 4.6.1 Boot Device Priority Boot Device Priority Boot Device Priority Boot Device Priority Boot Device Priority 1st ~ xxth Boot Device [1st Floppy Drive] 1st ~ xxth Boot Device [1st Floppy Drive] 1st ~ xxth Boot Device [1st Floppy Drive] 1st ~ xxth Boot Device [1st Floppy Drive] 1st ~ xxth Boot Device [1st Floppy Drive] These items specify the boot device priority sequence from the available devices. The number of device items that appears on the screen depends on the number of devices installed in the system. Configuration options: [xxxxx Drive] [Disabled] Boot Device Priority 1st Boot Device [1st FLOPPY DRIVE] 2nd Boot Device [PM-ST320410A] 3rd Boot Device [PS-ASUS CD-S520/A] 4th Boot Device [MBA v7.6.6 Slot 03] 5th Boot Device [MBA v7.6.6 Slot 02] Specifies the Boot Device Boot Priority sequence. Specifies the boot sequence from the availabe devices.
4-32 4-32 4-32 4-32 4-32 Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup 4.6.2 4.6.2 4.6.2 4.6.2 4.6.2 Boot Settings Configuration Boot Settings Configuration Boot Settings Configuration Boot Settings Configuration Boot Settings Configuration Boot Settings Configuration Quick Boot [Enabled] Full Screen Logo [Enabled] AddOn ROM Display Mode [ForceBIOS] Bootup Num-Lock [On] PS/2 Mouse Support [Auto] Wait For ‘F1’ If Error [Enabled] Hit ‘DEL’ Message Display [Enabled] Interrupt 19 Capture [Enabled] Allows BIOS to skip certain tests while booting. This will decrease the time needed to boot the system. Quick Boot [Enabled] Quick Boot [Enabled] Quick Boot [Enabled] Quick Boot [Enabled] Quick Boot [Enabled] Enabling this item allows the BIOS to skip some power on self tests (POST) while booting to decrease the time needed to boot the system. When set to [Disabled], BIOS performs all the POST items. Configuration options: [Disabled] [Enabled] Full Screen Logo [Enabled] Full Screen Logo [Enabled] Full Screen Logo [Enabled] Full Screen Logo [Enabled] Full Screen Logo [Enabled] This allows you to enable or disable the full screen logo display feature. Configuration options: [Disabled] [Enabled] Set this item to [Enabled] to use the ASUS MyLogo2™ feature. AddOn ROM Display Mode [ForceBIOS] AddOn ROM Display Mode [ForceBIOS] AddOn ROM Display Mode [ForceBIOS] AddOn ROM Display Mode [ForceBIOS] AddOn ROM Display Mode [ForceBIOS] Sets the display mode for the option ROM. Configuration options: [ForceBIOS] [Keep Current] Bootup Num-Lock [On] Bootup Num-Lock [On] Bootup Num-Lock [On] Bootup Num-Lock [On] Bootup Num-Lock [On] Allows you to select the power-on state for the NumLock. Configuration options: [Off] [On] PS/2 Mouse Support [Auto] PS/2 Mouse Support [Auto] PS/2 Mouse Support [Auto] PS/2 Mouse Support [Auto] PS/2 Mouse Support [Auto] Allows you to enable or disable support for PS/2 mouse. Configuration options: [Disabled] [Enabled] [Auto] Wait for ‘F1’ If Error [Enabled] Wait for ‘F1’ If Error [Enabled] Wait for ‘F1’ If Error [Enabled] Wait for ‘F1’ If Error [Enabled] Wait for ‘F1’ If Error [Enabled] When set to Enabled, the system waits for the F1 key to be pressed when error occurs. Configuration options: [Disabled] [Enabled]
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 4-33 4-33 4-33 4-33 4-33 Hit ‘DEL’ Message Display [Enabled] Hit ‘DEL’ Message Display [Enabled] Hit ‘DEL’ Message Display [Enabled] Hit ‘DEL’ Message Display [Enabled] Hit ‘DEL’ Message Display [Enabled] When set to Enabled, the system displays the message “Press DEL to run Setup” during POST. Configuration options: [Disabled] [Enabled] Interrupt 19 Capture [Enabled] Interrupt 19 Capture [Enabled] Interrupt 19 Capture [Enabled] Interrupt 19 Capture [Enabled] Interrupt 19 Capture [Enabled] When set to [Enabled], this function allows the option ROMs to trap Interrupt 19. Configuration options: [Disabled] [Enabled] 4.6.3 4.6.3 4.6.3 4.6.3 4.6.3 Security Security Security Security Security The Security menu items allow you to change the system security settings. Select an item then press <Enter> to display the configuration options. Security Settings Supervisor Password : Not Installed User Password : Not Installed Change Supervisor Password Change User Password <Enter> to change password. <Enter> again to disabled password. Change Supervisor Password Change Supervisor Password Change Supervisor Password Change Supervisor Password Change Supervisor Password Select this item to set or change the supervisor password. The Supervisor Password item on top of the screen shows the default Not Installed Not Installed Not Installed Not Installed Not Installed . After you set a password, this item shows Installed Installed Installed Installed Installed . To set a Supervisor Password: 1. Select the Change Supervisor Password item and press <Enter>. 2. From the password box, type a password composed of at least six letters and/or numbers, then press <Enter>. 3. Confirm the password when prompted. The message “Password Installed” appears after you successfully set your password. To change the supervisor password, follow the same steps as in setting a user password. To clear the supervisor password, select the Change Supervisor Password then press <Enter>. The message “Password Uninstalled” appears.
4-34 4-34 4-34 4-34 4-34 Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup After you have set a supervisor password, the other items appear to allow you to change other security settings. User Access Level (Full Access] User Access Level (Full Access] User Access Level (Full Access] User Access Level (Full Access] User Access Level (Full Access] This item allows you to select the access restriction to the Setup items. Configuration options: [No Access] [View Only] [Limited] [Full Access] No Access No Access No Access No Access No Access prevents user access to the Setup utility. View Only View Only View Only View Only View Only allows access but does not allow change to any field. Limited Limited Limited Limited Limited allows changes only to selected fields, such as Date and Time. Full Access Full Access Full Access Full Access Full Access allows viewing and changing all the fields in the Setup utility. Change User Password Change User Password Change User Password Change User Password Change User Password Select this item to set or change the user password. The User Password item on top of the screen shows the default Not Installed Not Installed Not Installed Not Installed Not Installed . After you set a password, this item shows Installed Installed Installed Installed Installed . To set a User Password: 1. Select the Change User Password item and press <Enter>. 2. On the password box that appears, type a password composed of at least six letters and/or numbers, then press <Enter>. 3. Confirm the password when prompted. If you forget your BIOS password, you can clear it by erasing the CMOS Real Time Clock (RTC) RAM. See section “2.6 Jumpers” for information on how to erase the RTC RAM. Security Settings Supervisor Password : Not Installed User Password : Not Installed Change Supervisor Password User Access Level [Full Access] Change User Password Clear User Password Password Check [Setup] <Enter> to change password. <Enter> again to disabled password.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 4-35 4-35 4-35 4-35 4-35 The message “Password Installed” appears after you set your password successfully. To change the user password, follow the same steps as in setting a user password. Clear User Password Clear User Password Clear User Password Clear User Password Clear User Password Select this item to clear the user password. Password Check [Setup] Password Check [Setup] Password Check [Setup] Password Check [Setup] Password Check [Setup] When set to [Setup], BIOS checks for user password when accessing the Setup utility. When set to [Always], BIOS checks for user password both when accessing Setup and booting the system. Configuration options: [Setup] [Always] 4.7 Exit menu Pressing <Esc> does not immediately exit this menu. Select one of the options from this menu or <F10> from the legend bar to exit. The Exit menu items allow you to load the optimal or failsafe default values for the BIOS items, and save or discard your changes to the BIOS items. Exit Options Exit & Save Changes Exit & Discard Changes Discard Changes Load Setup Defaults Exit system setup after saving the changes. F10 key can be used for this operation.
4-36 4-36 4-36 4-36 4-36 Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Chapter 4: BIOS setup Exit & Discard Changes Exit & Discard Changes Exit & Discard Changes Exit & Discard Changes Exit & Discard Changes Select this option only if you do not want to save the changes that you made to the Setup program. If you made changes to fields other than System Date, System Time, and Password, the BIOS asks for a confirmation before exiting. Discard Changes Discard Changes Discard Changes Discard Changes Discard Changes This option allows you to discard the selections you made and restore the previously saved values. After selecting this option, a confirmation appears. Select [OK] to discard any changes and load the previously saved values. Load Setup Defaults Load Setup Defaults Load Setup Defaults Load Setup Defaults Load Setup Defaults This option allows you to load the default values for each of the parameters on the Setup menus. When you select this option or if you press <F5>, a confirmation window appears. Select [OK] to load default values. Select Exit & Save Changes Exit & Save Changes Exit & Save Changes Exit & Save Changes Exit & Save Changes o r make other changes before saving the values to the non-volatile RAM. If you attempt to exit the Setup program without saving your changes, the program prompts you with a message asking if you want to save your changes before exiting. Press <Enter> to save the changes while exiting. Exit & Save Changes Exit & Save Changes Exit & Save Changes Exit & Save Changes Exit & Save Changes Once you are finished making your selections, choose this option from the Exit menu to ensure the values you selected are saved to the CMOS RAM. An onboard backup battery sustains the CMOS RAM so it stays on even when the PC is turned off. When you select this option, a confirmation window appears. Select [OK] to save changes and exit.
5 RAID support This chapter provides information on RAID configurations for this motherboard.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M Chapter summary 5 5.1 RAID configurations .............................................................. 5-1
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 5-1 5-1 5-1 5-1 5-1 5.1 RAID configurations The server system/motherboard comes with the Intel Intel Intel Intel Intel ® ® ® ® ® ICH7R ICH7R ICH7R ICH7R ICH7R and the LSI Logic Embedded SATA RAID LSI Logic Embedded SATA RAID LSI Logic Embedded SATA RAID LSI Logic Embedded SATA RAID LSI Logic Embedded SATA RAID technology built-in the Intel ® ICH7R SouthBridge chipset that allows you to configure IDE and Serial ATA hard disk drives as RAID sets. The motherboard supports the following RAID configurations: 5.1.1 5.1.1 5.1.1 5.1.1 5.1.1 RAID definitions RAID definitions RAID definitions RAID definitions RAID definitions RAID 0 RAID 0 RAID 0 RAID 0 RAID 0 (Data striping) optimizes two identical hard disk drives to read and write data in parallel, interleaved stacks. Two hard disks perform the same work as a single drive but at a sustained data transfer rate, double that of a single disk alone, thus improving data access and storage. Use of two new identical hard disk drives is required for this setup. RAID 1 RAID 1 RAID 1 RAID 1 RAID 1 (Data mirroring) copies and maintains an identical image of data from one drive to a second drive. If one drive fails, the disk array management software directs all applications to the surviving drive as it contains a complete copy of the data in the other drive. This RAID configuration provides data protection and increases fault tolerance to the entire system. Use two new drives or use an existing drive and a new drive for this setup. The new drive must be of the same size or larger than the existing drive. RAID 5 RAID 5 RAID 5 RAID 5 RAID 5 stripes both data and parity information across three or more hard disk drives. Among the advantages of RAID 5 configuration include better HDD performance, fault tolerance, and higher storage capacity. The RAID 5 configuration is best suited for transaction processing, relational database applications, enterprise resource planning, and other business systems. Use a minimum of three identical hard disk drives for this setup. RAID 10 RAID 10 RAID 10 RAID 10 RAID 10 i s a striped configuration with RAID 1 segments whose segments are RAID 1 arrays. This configuration has the same fault tolerance as RAID 1, and has the same overhead for fault-tolerance as mirroring alone. RAID 10 achieves high input/output rates by striping RAID 1 segments. In some instances, a RAID 10 configuration can sustain multiple simultaneous drive failure. A minimum of four hard disk drives is required for this setup. Intel Intel Intel Intel Intel ® Matrix Storage Matrix Storage Matrix Storage Matrix Storage Matrix Storage . The Intel ® Matrix Storage technology supported by the ICH7R chip allows you to create a RAID 0 and a RAID 1 set using only two identical hard disk drives. The Intel ® Matrix Storage technology creates two partitions on each hard disk drive to create a virtual RAID 0 and RAID 1 sets. This technology also allows you to change the hard disk drive partition size without losing any data. If you want to boot the system from a hard disk drive included in a created RAID set, copy first the RAID driver from the support CD to a floppy disk before you install an operating system to the selected hard disk drive. Refer to section “2. RAID driver installation” for details.
5-2 5-2 5-2 5-2 5-2 Chapter 5: D Chapter 5: D Chapter 5: D Chapter 5: D Chapter 5: D river installation river installation river installation river installation river installation 5.1.3 5.1.3 5.1.3 5.1.3 5.1.3 Intel Intel Intel Intel Intel ® ® ® ® ® RAID configurations RAID configurations RAID configurations RAID configurations RAID configurations This motherboard supports RAID 0, RAID 1, and Intel ® Matrix Storage configurations for Serial ATA hard disks drives through the Intel ® ICH7R Southbridge chip. Setting the RAID item in BIOS Setting the RAID item in BIOS Setting the RAID item in BIOS Setting the RAID item in BIOS Setting the RAID item in BIOS You must set the RAID item in the BIOS Setup before you can create a RAID set(s). To do this: 1. Enter the BIOS Setup during POST. 2. Go to the Main Menu Main Menu Main Menu Main Menu Main Menu , select IDE Configuration IDE Configuration IDE Configuration IDE Configuration IDE Configuration , then press <Enter>. 3. Select the item Configure SATA As Configure SATA As Configure SATA As Configure SATA As Configure SATA As , then press <Enter> to display the configuration options. 4. Select RAID RAID RAID RAID RAID from the Configure SATA As Configure SATA As Configure SATA As Configure SATA As Configure SATA As item options, then press <Enter>. 5. Select the item Onboard Serial-ATA BOOTROM Onboard Serial-ATA BOOTROM Onboard Serial-ATA BOOTROM Onboard Serial-ATA BOOTROM Onboard Serial-ATA BOOTROM , press <Enter>, then select Enabled Enabled Enabled Enabled Enabled from the options. 6. Save your changes, then exit the BIOS Setup. Refer to the system or the motherboard user guide for details on entering and navigating through the BIOS Setup. 5.1.2 5.1.2 5.1.2 5.1.2 5.1.2 Installing Serial ATA hard disks Installing Serial ATA hard disks Installing Serial ATA hard disks Installing Serial ATA hard disks Installing Serial ATA hard disks The motherboard supports Serial ATA hard disk drives. For optimal performance, install identical drives of the same model and capacity when creating a disk array. To install the SATA hard disks for a RAID configuration: 1. Install the SATA hard disks into the drive bays. 2. Connect the SATA signal cables. 3. Connect a SATA power cable to the power connector on each drive.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 5-3 5-3 5-3 5-3 5-3 Intel Intel Intel Intel Intel ® ® ® ® ® Matrix Storage Manager Option ROM Utility Matrix Storage Manager Option ROM Utility Matrix Storage Manager Option ROM Utility Matrix Storage Manager Option ROM Utility Matrix Storage Manager Option ROM Utility The Intel ® Matrix Storage Manager Option ROM utility allows you to create RAID 0, RAID 1, RAID 10 (RAID 0 1), and RAID 5 set(s) from Serial ATA hard disk drives that are connected to the Serial ATA connectors supported by the Southbridge. To enter the Intel ® Application Accelerator RAID Option ROM utility: 1. Install all the Serial ATA hard disk drives. 2. Turn on the system. 3. During POST, press <Ctrl I> to display the utility main menu. Intel(R) Matrix Storage Manager Option ROM v5.0.0.1032 ICH7R wRAID5 Copyright(C) 2003-05 Intel Corporation. All Rights Reserved. [ MAIN MENU ] 1. Create RAID Volume 2. Delete RAID Volume 3. Reset Disks to Non-RAID 4. Exit [ DISK/VOLUME INFORMATION ] RAID Volumes: None defined. Physical Disks: Port Drive Model Serial # Size Type/Status(Vol ID) 0 XXXXXXXXXXX XXXXXXXX XX.XXGB Non-RAID Disk 1 XXXXXXXXXXX XXXXXXXX XX.XXGB Non-RAID Disk 2 XXXXXXXXXXX XXXXXXXX XX.XXGB Non-RAID Disk 3 XXXXXXXXXXX XXXXXXXX XX.XXGB Non-RAID Disk [ ↑↓ ↑↓ ↑↓ ↑↓ ↑↓ ]-Select [ESC]-Exit [ENTER]-Select Menu The navigation keys at the bottom of the screen allow you to move through the menus and select the menu options. The RAID BIOS setup screens shown in this section are for reference only and may not exactly match the items on your screen.
5-4 5-4 5-4 5-4 5-4 Chapter 5: D Chapter 5: D Chapter 5: D Chapter 5: D Chapter 5: D river installation river installation river installation river installation river installation Creating a RAID 0 set (striped) Creating a RAID 0 set (striped) Creating a RAID 0 set (striped) Creating a RAID 0 set (striped) Creating a RAID 0 set (striped) To create a RAID 0 set: 1. From the utility main menu, select 1. Create RAID Volume 1. Create RAID Volume 1. Create RAID Volume 1. Create RAID Volume 1. Create RAID Volume , then press <Enter>. This screen appears. 2. Enter a name for the RAID 0 set, then press <Enter>. 3. When the RAID Level RAID Level RAID Level RAID Level RAID Level item is highlighted, press the up/down arrow key to select RAID 0(Stripe) RAID 0(Stripe) RAID 0(Stripe) RAID 0(Stripe) RAID 0(Stripe) , then press <Enter>. 4. When the Disks Disks Disks Disks Disks item is highlighted, press <Enter> to select the hard disk drives to configure as RAID. This pop-up screen appears. Intel(R) Matrix Storage Manager Option ROM v5.0.0.1032 ICH7R wRAID5 Copyright(C) 2003-05 Intel Corporation. All Rights Reserved. [ CREATE ARRAY MENU ] [ DISK/VOLUME INFORMATION ] Enter a string between 1 and 16 characters in length that can be used to uniquely identify the RAID volume. This name is case sensitive and cannot contain special characters. [ ↑↓ ↑↓ ↑↓ ↑↓ ↑↓ ]-Change [TAB]-Next [ESC]-Previous Menu [Enter]-Select Name: RAID Level: Disks: Strip Size: Capacity: Volume0 RAID0(Stripe) Select Disks 128KB 0.0 GB Create Volume [ SELECT DISKS ] [ ↑↓ ↑↓ ↑↓ ↑↓ ↑↓ ]-Previous/Next [SPACE]-Selects [ENTER]-Selection Complete Port Drive Model Serial # Size Status 0 XXXXXXXXXXXX XXXXXXXX XX.XGB Non-RAID Disk 1 XXXXXXXXXXXX XXXXXXXX XX.XGB Non-RAID Disk 2 XXXXXXXXXXXX XXXXXXXX XX.XGB Non-RAID Disk 3 XXXXXXXXXXXX XXXXXXXX XX.XGB Non-RAID Disk Select 2 to 4 disks to use in creating the volume. 5. Use the up/down arrow key to highlight a drive, then press <Space> to select. A small triangle marks the selected drive. Press <Enter> after completing your selection.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 5-5 5-5 5-5 5-5 5-5 6. Use the up/down arrow key to select the stripe size for the RAID 0 array, then press <Enter>. The available stripe size values range from 4 KB to 128 KB. The default stripe size is 128 KB. TIP: TIP: TIP: TIP: TIP: W e recommend a lower stripe size for server systems, and a higher stripe size for multimedia computer systems used mainly for audio and video editing. 7. Key in the RAID volume capacity that you want, then press <Enter>. The default value indicates the maximum allowed capacity. 8. Press <Enter> when the Create Volume Create Volume Create Volume Create Volume Create Volume item is highlighted. This warning message appears. WARNING: ALL DATA ON SELECTED DISKS WILL BE LOST. Are you sure you want to create this volume? (Y/N): 9. Press <Y> to create the RAID volume and return to the main menu, or <N> to go back to the Create Volume menu.
5-6 5-6 5-6 5-6 5-6 Chapter 5: D Chapter 5: D Chapter 5: D Chapter 5: D Chapter 5: D river installation river installation river installation river installation river installation Creating a RAID 1 set (mirrored) Creating a RAID 1 set (mirrored) Creating a RAID 1 set (mirrored) Creating a RAID 1 set (mirrored) Creating a RAID 1 set (mirrored) To create a RAID 1 set: 1. From the utility main menu, select 1. Create RAID Volume 1. Create RAID Volume 1. Create RAID Volume 1. Create RAID Volume 1. Create RAID Volume , then press <Enter>. This screen appears. 2. Enter a name for the RAID 1 set, then press <Enter>. 3. When the RAID Level RAID Level RAID Level RAID Level RAID Level item is highlighted, press the up/down arrow key to select RAID 1(Mirror) RAID 1(Mirror) RAID 1(Mirror) RAID 1(Mirror) RAID 1(Mirror) , then press <Enter>. 4. When the Capacity Capacity Capacity Capacity Capacity item is highlighted, key in the RAID volume capacity that you want, then press <Enter>. The default value indicates the maximum allowed capacity. 5. Press <Enter> when the Create Volume Create Volume Create Volume Create Volume Create Volume item is highlighted. This warning message appears. Intel(R) Matrix Storage Manager Option ROM v5.0.0.1032 ICH7R wRAID5 Copyright(C) 2003-05 Intel Corporation. All Rights Reserved. [ CREATE ARRAY MENU ] [ DISK/VOLUME INFORMATION ] Enter a string between 1 and 16 characters in length that can be used to uniquely identify the RAID volume. This name is case sensitive and cannot contain special characters. [ ↑↓ ↑↓ ↑↓ ↑↓ ↑↓ ]-Change [TAB]-Next [ESC]-Previous Menu [Enter]-Select Name: RAID Level: Disks: Strip Size: Capacity: Volume1 RAID1(Mirror) Select Disks N/A XX.X GB Create Volume WARNING: ALL DATA ON SELECTED DISKS WILL BE LOST. Are you sure you want to create this volume? (Y/N): 6. Press <Y> to create the RAID volume and return to main menu or <N> to go back to Create Volume menu.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 5-7 5-7 5-7 5-7 5-7 Creating a RAID 10 set (RAID 0 1) Creating a RAID 10 set (RAID 0 1) Creating a RAID 10 set (RAID 0 1) Creating a RAID 10 set (RAID 0 1) Creating a RAID 10 set (RAID 0 1) To create a RAID 10 set: 1. From the utility main menu, select 1. Create RAID Volume 1. Create RAID Volume 1. Create RAID Volume 1. Create RAID Volume 1. Create RAID Volume , then press <Enter>. This screen appears. Intel(R) Matrix Storage Manager Option ROM v5.0.0.1032 ICH7R wRAID5 Copyright(C) 2003-05 Intel Corporation. All Rights Reserved. [ CREATE ARRAY MENU ] [ DISK/VOLUME INFORMATION ] Enter a string between 1 and 16 characters in length that can be used to uniquely identify the RAID volume. This name is case sensitive and cannot contain special characters. Name: RAID Level: Disks: Strip Size: Capacity: Volume10 RAID10(RAID0 1) Select Disks 128KB XXX.X GB Create Volume 2. Enter a name for the RAID 10 set, then press <Enter>. 3. When the RAID Level RAID Level RAID Level RAID Level RAID Level item is highlighted, press the up/down arrow key to select RAID 10(RAID0 1) RAID 10(RAID0 1) RAID 10(RAID0 1) RAID 10(RAID0 1) RAID 10(RAID0 1) , then press <Enter>. 4. When the Stripe Size Stripe Size Stripe Size Stripe Size Stripe Size item is highlighted, press the up/down arrow key to select the stripe size for the RAID 10 array, then press <Enter>. The available stripe size values range from 4 KB to 128 KB. The default stripe size is 64 KB. TIP: TIP: TIP: TIP: TIP: W e recommend a lower stripe size for server systems, and a higher stripe size for multimedia computer systems used mainly for audio and video editing. 5. Key in the RAID volume capacity that you want then press <Enter> when the Capacity Capacity Capacity Capacity Capacity item is highlighted. The default value indicates the maximum allowed capacity. [ ↑↓ ↑↓ ↑↓ ↑↓ ↑↓ ]-Change [TAB]-Next [ESC]-Previous Menu [Enter]-Select
5-8 5-8 5-8 5-8 5-8 Chapter 5: D Chapter 5: D Chapter 5: D Chapter 5: D Chapter 5: D river installation river installation river installation river installation river installation Creating a RAID 5 set (parity) Creating a RAID 5 set (parity) Creating a RAID 5 set (parity) Creating a RAID 5 set (parity) Creating a RAID 5 set (parity) To create a RAID 5 set: 1. From the utility main menu, select 1. Create RAID Volume 1. Create RAID Volume 1. Create RAID Volume 1. Create RAID Volume 1. Create RAID Volume , then press <Enter>. This screen appears. Intel(R) Matrix Storage Manager Option ROM v5.0.0.1032 ICH7R wRAID5 Copyright(C) 2003-05 Intel Corporation. All Rights Reserved. [ CREATE ARRAY MENU ] [ DISK/VOLUME INFORMATION ] Enter a string between 1 and 16 characters in length that can be used to uniquely identify the RAID volume. This name is case sensitive and cannot contain special characters. Name: RAID Level: Disks: Strip Size: Capacity: Volume5 RAID5(Parity) Select Disks 64KB 0.0 GB Create Volume WARNING: ALL DATA ON SELECTED DISKS WILL BE LOST. Are you sure you want to create this volume? (Y/N): 7. Press <Y> to create the RAID volume and return to the main menu or <N> to go back to the Create Volume menu. [ ↑↓ ↑↓ ↑↓ ↑↓ ↑↓ ]-Change [TAB]-Next [ESC]-Previous Menu [Enter]-Select 6. Press <Enter> when the Create Volume Create Volume Create Volume Create Volume Create Volume item is highlighted. This warning message appears. 2. Enter a name for the RAID 5 set, then press <Enter>. 3. When the RAID Level RAID Level RAID Level RAID Level RAID Level item is highlighted, press the up/down arrow key to select RAID 5(Parity) RAID 5(Parity) RAID 5(Parity) RAID 5(Parity) RAID 5(Parity) , then press <Enter>.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 5-9 5-9 5-9 5-9 5-9 4. The Disks item is highlighted, press <Enter> to select the hard disk drives to configure as RAID. The following pop-up screen appears. [ SELECT DISKS ] [ ↑↓ ↑↓ ↑↓ ↑↓ ↑↓ ]-Previous/Next [SPACE]-Selects [ENTER]-Selection Complete Port Drive Model Serial # Size Status 0 XXXXXXXXXXXX XXXXXXXX XX.XGB Non-RAID Disk 1 XXXXXXXXXXXX XXXXXXXX XX.XGB Non-RAID Disk 2 XXXXXXXXXXXX XXXXXXXX XX.XGB Non-RAID Disk 3 XXXXXXXXXXXX XXXXXXXX XX.XGB Non-RAID Disk Select 2 to 4 disks to use in creating the volume. 5. Use the up/down arrow key to highlight the drive you want to set, then press <Space> to select. A small triangle marks the selected drive. Press <Enter> after completing your selection. 6. When the Stripe Size Stripe Size Stripe Size Stripe Size Stripe Size item is highlighted, press the up/down arrow key to select the stripe size for the RAID 5 array, then press <Enter>. The available stripe size values range from 4 KB to 128 KB. The default stripe size is 64 KB. TIP: TIP: TIP: TIP: TIP: W e recommend a lower stripe size for server systems, and a higher stripe size for multimedia computer systems used mainly for audio and video editing. 7. Key in the RAID volume capacity that you want, then press <Enter> when the Capacity Capacity Capacity Capacity Capacity item is highlighted. The default value indicates the maximum allowed capacity. 8. Press <Enter> when the Create Volume Create Volume Create Volume Create Volume Create Volume item is highlighted. This warning message appears. WARNING: ALL DATA ON SELECTED DISKS WILL BE LOST. Are you sure you want to create this volume? (Y/N): 9. Press <Y> to create the RAID volume and return to the main menu or <N> to go back to the Create Volume menu.
5-10 5-10 5-10 5-10 5-10 Chapter 5: D Chapter 5: D Chapter 5: D Chapter 5: D Chapter 5: D river installation river installation river installation river installation river installation Deleting a RAID set Deleting a RAID set Deleting a RAID set Deleting a RAID set Deleting a RAID set Take caution when deleting a RAID set. You will lose all data on the hard disk drives when you delete a RAID set. To delete a RAID set: 1. From the utility main menu, select 2. Delete RAID Volume 2. Delete RAID Volume 2. Delete RAID Volume 2. Delete RAID Volume 2. Delete RAID Volume , then press <Enter> to display this screen. 2. Use the up/down arrow key to select the RAID set you want to delete, then press <Del>. This window appears. Intel(R) Matrix Storage Manager Option ROM v5.0.0.1032 ICH7R wRAID5 Copyright(C) 2003-05 Intel Corporation. All Rights Reserved. [ DELETE VOLUME MENU ] Name Level Drives Capacity Status Bootable Volume0 RAIDX(xxxxx) X XXX.XGB Normal Yes [ HELP ] Deleting a volume will destroy the volume data on the drive(s) and cause any member disks to become available as non-RAID disks. WARNING: EXISTING DATA WITHIN THIS VOLUME WILL BE LOST AND NON-RECOVERABLE. [ ↑↓ ↑↓ ↑↓ ↑↓ ↑↓ ]-Select [<ESC>]-Previous Menu [<Del>]-Delete Volume 3. Press <Y> to delete the RAID set and return to the utility main menu; otherwise, press <N> to return to the Delete Volume menu. ALL DATA IN THE VOLUME WILL BE LOST! Are you sure you want to delete volume “VolumeX”? (Y/N): [ DELETE VOLUME VERIFICATION ]
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 5-11 5-11 5-11 5-11 5-11 Exiting the Intel Exiting the Intel Exiting the Intel Exiting the Intel Exiting the Intel ® ® ® ® ® Matrix Storage Manager utility Matrix Storage Manager utility Matrix Storage Manager utility Matrix Storage Manager utility Matrix Storage Manager utility To exit the utility: 1. From the utility main menu, select 4. Exit 4. Exit 4. Exit 4. Exit 4. Exit , then press <Enter>. This window appears. Are you sure you want to exit? (Y/N): [ CONFIRM EXIT ] 2. Press <Y> to exit or press <N> to return to the utility main menu. Resetting Disks to Non-RAID Resetting Disks to Non-RAID Resetting Disks to Non-RAID Resetting Disks to Non-RAID Resetting Disks to Non-RAID Take caution before you reset a RAID volume HDD to non-RAID. Resetting a RAID volume HDD deletes all internal RAID structure on the drive. To reset a RAID set hard disk drive: 1. From the utility main menu, select 3. Reset Disks to Non-RAID 3. Reset Disks to Non-RAID 3. Reset Disks to Non-RAID 3. Reset Disks to Non-RAID 3. Reset Disks to Non-RAID , then press <Enter> to display this screen. 2. Use the up/down arrow key to highlight the RAID set drive you want to reset, then press <Space> to select. 3. Press <Enter> to reset the RAID set drive. A confirmation message appears. 4. Press <Y> to reset the drive or press <N> to return to the utility main menu. [ RESET RAID DATA ] Resetting RAID data will remove internal RAID structures from the selected RAID disks. By removing these structures, the drive will revert back to a non-RAID disk. WARNING: Resetting a disk causes all data on the disk to be lost. Port Drive Model Serial # Size Status 0 XXXXXXXXXXXX XXXXXXXX XX.XGB Member Disk 1 XXXXXXXXXXXX XXXXXXXX XX.XGB Member Disk Select the disks that should be reset. [ ↑↓ ↑↓ ↑↓ ↑↓ ↑↓ ]-Previous/Next [SPACE]-Selects [ENTER]-Selection Complete
5-12 5-12 5-12 5-12 5-12 Chapter 5: D Chapter 5: D Chapter 5: D Chapter 5: D Chapter 5: D river installation river installation river installation river installation river installation Resetting a RAID set hard disks drive Resetting a RAID set hard disks drive Resetting a RAID set hard disks drive Resetting a RAID set hard disks drive Resetting a RAID set hard disks drive Take caution before you reset a RAID volume HDD to non-RAID. Resetting a RAID volume HDD deletes all internal RAID structure on the drive. To reset a RAID set hard disk drive: 1. From the utility main menu, select [3. Reset Disks to Non-RAID] [3. Reset Disks to Non-RAID] [3. Reset Disks to Non-RAID] [3. Reset Disks to Non-RAID] [3. Reset Disks to Non-RAID] , then press <Enter> to display the following screen. Resetting RAID data will remove the internal RAID structures from the selected RAID disks. By removing these structures the drive will revert back to a Non-RAID disk. [ RESET RAID DATA ] WARNING: Resetting a disk causes all data on the disk to be lost. Port Drive Model Serial # Size Status 0 STXXXXXXXXX XXXXXXXX XX.0GB Member Disk 1 STXXXXXXXXX XXXXXXXX XX.0GB Member Disk Select the disk that should be reset [ ]-Previous/Next [ ]-Previous/Next [Space]-Selects [Space]-Selects [Enter]-Selection Complete [Enter]-Selection Complete 2. Use the up or down arrow keys to highlight the RAID set drive you want to reset, then press <Space> to select. 3. Press <Enter> to reset the RAID set drive. A confirmation window appears. 4. Press <Y> to reset the drive; otherwise, press <N> to return to the utility main menu. 5. Follow steps 2 to 4 to select and reset other RAID set drives.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 5-13 5-13 5-13 5-13 5-13 5.1.4 5.1.4 5.1.4 5.1.4 5.1.4 LSI Logic Embedded SATA RAID Setup Utility LSI Logic Embedded SATA RAID Setup Utility LSI Logic Embedded SATA RAID Setup Utility LSI Logic Embedded SATA RAID Setup Utility LSI Logic Embedded SATA RAID Setup Utility The LSI Logic Embedded SATA RAID Setup Utility allows you to create RAID 0, RAID 1, and RAID 10 set(s) from SATA hard disk drives connected to the SATA connectors supported by the motherboard Southbridge chip. You may also create a RAID set(s) in a Windows ® operating environment using the Global Array Manager (GAM) application. Refer to the GAM user guide in the motherboard support CD for details. To enter the LSI Logic Embedded SATA RAID Setup Utility: 1. Turn on the system after installing all the SATA hard disk drives. 2. During POST, the LSI Logic Embedded SATA RAID Setup Utility automatically detects the installed SATA hard disk drives and displays any existing RAID set(s). Press <Ctrl> <M> to enter the utility. The LSI Logic Embedded SATA RAID automatically configures a RAID 1 (Mirrored) set when the SATA is configured as RAID SATA is configured as RAID SATA is configured as RAID SATA is configured as RAID SATA is configured as RAID i n the BIOS and you installed two hard disk drives without a RAID configuration.
5-14 5-14 5-14 5-14 5-14 Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation Menu Menu Menu Menu Menu Description Description Description Description Description Configure Allows you to create RAID 0, RAID 1, or RAID 10 set using the Easy Configuration or the New Configuration command. This menu also allows you to view, add, or clear RAID configurations or select the boot drive Initialize Allows you to initialize the logical drives of a created RAID set Objects Allows you to initialize logical drives or change the logical drive parameters Rebuild Allows you to rebuild failed drives Check Consistency Allows you to check the data consistency of the logical drives of a created RAID set Creating a RAID set Creating a RAID set Creating a RAID set Creating a RAID set Creating a RAID set The LSI Logic Embedded SATA RAID Setup Utility allows you to create a RAID 0 or RAID 1 set using two types of configurations: Easy Easy Easy Easy Easy and New New New New New . In Easy Configuration Easy Configuration Easy Configuration Easy Configuration Easy Configuration , the logical drive parameters are set automatically including the size and stripe size (RAID 1 only). In New Configuration New Configuration New Configuration New Configuration New Configuration , you manually set the logical drive parameters and assign the set size and stripe size (RAID 1 only). 3. The utility main window appears. Use the arrow keys to select an option from the Management Menu Management Menu Management Menu Management Menu Management Menu , then press <Enter>. Refer to the Management Menu descriptions below. At the bottom of the screen is the legend box. The keys on the legend box allow you to navigate through the setup menu options or execute commands. The keys on the legend box vary according to the menu level.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 5-15 5-15 5-15 5-15 5-15 Using Easy Configuration To create a RAID set using the Easy Configuration Easy Configuration Easy Configuration Easy Configuration Easy Configuration option: 1. From the utility main menu, highlight Configure Configure Configure Configure Configure , then press <Enter>. 2. Use the arrow keys to select Easy Configuration Easy Configuration Easy Configuration Easy Configuration Easy Configuration , then press <Enter>. 3. The ARRAY SELECTION MENU ARRAY SELECTION MENU ARRAY SELECTION MENU ARRAY SELECTION MENU ARRAY SELECTION MENU displays the available drives connected to the SATA ports. Select the drives you want to include in the RAID set, then press <SpaceBar>. When selected, t he drive indicator changes from READY READY READY READY READY t o ONLIN A[X]-[Y] ONLIN A[X]-[Y] ONLIN A[X]-[Y] ONLIN A[X]-[Y] ONLIN A[X]-[Y] , where X is the array number, and Y is the drive number. The information of the selected hard disk drive displays at the bottom of the screen.
5-16 5-16 5-16 5-16 5-16 Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation 4. Select all the drives required for the RAID set, then press <Enter>. The configurable array appears on screen. 5. Press <F10>, select the configurable array, then press <SpaceBar>. The logical drive information appears including a Logical Drive menu that allows you to change the logical drive parameters.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 5-17 5-17 5-17 5-17 5-17 6. Select RAID RAID RAID RAID RAID from the Logical Drive Logical Drive Logical Drive Logical Drive Logical Drive menu, then press <Enter>. 7. Select the RAID level from the menu, then press <Enter>. You need at least two identical hard disk drives when creating a RAID 1 set. 8. When creating a RAID 1 or a RAID 10 set, select Stripe Size Stripe Size Stripe Size Stripe Size Stripe Size from the Logical Drive Logical Drive Logical Drive Logical Drive Logical Drive menu, then press <Enter>. When creating a RAID 0 set, proceed to step 10. 9. Key-in the stripe size, then press <Enter>. For server systems, we recommend that you use a lower array block size. For multimedia computer systems used mainly for audio and video editing, we recommend a higher array block size for optimum performance.
5-18 5-18 5-18 5-18 5-18 Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation 10. When finished setting the selected logical drive configuration, select Accept Accept Accept Accept Accept from the menu, then press <Enter>. 11. When finished setting the selected logical drive configuration, select Accept Accept Accept Accept Accept from the menu, then press <Enter>. 12. Follow steps 5 to 10 to configure additional logical drives. 13. When prompted, save the configuration, then press <Esc> to return to the Management Menu.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 5-19 5-19 5-19 5-19 5-19 Using New Configuration When a RAID set is already existing, using the New Configuration New Configuration New Configuration New Configuration New Configuration command erases the existing RAID configuration data. If you do not want to delete the existing RAID set, use the View/Add Configuration View/Add Configuration View/Add Configuration View/Add Configuration View/Add Configuration command to view or create another RAID configuration. To create a RAID set using the New Configuration New Configuration New Configuration New Configuration New Configuration option: 1. From the utility main menu, highlight Configure Configure Configure Configure Configure , then press <Enter>. 2. Use the arrow keys to select New Configuration New Configuration New Configuration New Configuration New Configuration , then press <Enter>. 3. Follow steps 3 to 7 of the previous section. 4. Select Size Size Size Size Size from the Logical Drive Logical Drive Logical Drive Logical Drive Logical Drive menu, then press <Enter>. 5. Key-in the desired logical drive size, then press <Enter>. 6. Follow steps 8 to 13 of the previous section to create the RAID set.
5-20 5-20 5-20 5-20 5-20 Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation Adding or viewing a RAID configuration Adding or viewing a RAID configuration Adding or viewing a RAID configuration Adding or viewing a RAID configuration Adding or viewing a RAID configuration You can add a new RAID configuration or view an existing configuration using the View/Add Configuration View/Add Configuration View/Add Configuration View/Add Configuration View/Add Configuration command. Adding a new RAID configuration To add a new RAID configuration: 1. From the Management Menu, highlight Configure Configure Configure Configure Configure , then press <Enter>. 2. Use the arrow keys to select View/Add Configuration View/Add Configuration View/Add Configuration View/Add Configuration View/Add Configuration , then press <Enter>. 3. The ARRAY SELECTION MENU ARRAY SELECTION MENU ARRAY SELECTION MENU ARRAY SELECTION MENU ARRAY SELECTION MENU displays the available drives connected to the SATA ports. Select the drive(s) you want to include in the RAID set, then press <SpaceBar>. When selected, t he drive indicator changes from READY READY READY READY READY t o ONLIN A[X]-[Y] ONLIN A[X]-[Y] ONLIN A[X]-[Y] ONLIN A[X]-[Y] ONLIN A[X]-[Y] , where X is the array number, and Y is the drive number. The information of the selected hard disk drive displays at the bottom of the screen.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 5-21 5-21 5-21 5-21 5-21 4. Select all the drives required for the RAID set, then press <Enter>. The configurable array appears on screen. 5. Press <F10>, select the configurable array, then press <SpaceBar>. The logical drive information appears including a Logical Drive menu that allows you to change the logical drive parameters.
5-22 5-22 5-22 5-22 5-22 Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation 6. Follow steps 6 to 7 of the Creating a RAID set: Using Easy Creating a RAID set: Using Easy Creating a RAID set: Using Easy Creating a RAID set: Using Easy Creating a RAID set: Using Easy Configuration Configuration Configuration Configuration Configuration section. 7. Select Size Size Size Size Size from the Logical Drive Logical Drive Logical Drive Logical Drive Logical Drive menu, then press <Enter>. 8. Key-in the desired logical drive size, then press <Enter>. 9. Follow steps 8 to 13 of the Creating a RAID set: Using Easy Creating a RAID set: Using Easy Creating a RAID set: Using Easy Creating a RAID set: Using Easy Creating a RAID set: Using Easy Configuration Configuration Configuration Configuration Configuration section to add the new RAID configuration.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 5-23 5-23 5-23 5-23 5-23 Initializing the logical drives Initializing the logical drives Initializing the logical drives Initializing the logical drives Initializing the logical drives After creating the RAID set(s), you must initialize the logical drives. You may initialize the logical drives of a RAID set(s) using the Initialize Initialize Initialize Initialize Initialize o r Objects Objects Objects Objects Objects command on the Management Menu. Using the Initialize command To initialize the logical drive using the Initialize Initialize Initialize Initialize Initialize command: 1. From the Management Menu, highlight Initialize Initialize Initialize Initialize Initialize , then press <Enter>. 2. The screen displays the available RAID set(s) and prompts you to select the logical drive to initialize. Use the arrow keys to select the logical drive from the Logical Drive Logical Drive Logical Drive Logical Drive Logical Drive selection, then press <Enter>.
5-24 5-24 5-24 5-24 5-24 Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation 3. When prompted, press the <SpaceBar> to select Yes Yes Yes Yes Yes from the Initialize? Initialize? Initialize? Initialize? Initialize? dialog box, then press <Enter>. You may also press <F10> to initialize the drive without confirmation. Initializing a logical drive(s) erases all data on the drive. 4. A progress bar appears on screen. If desired, press <Esc> to abort initialization.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 5-25 5-25 5-25 5-25 5-25 5. When initialization is completed, press <Esc>. Using the Objects command To initialize the logical drives using the Objects Objects Objects Objects Objects command: 1. From the Management Menu, highlight Objects Objects Objects Objects Objects , then press <Enter>.
5-26 5-26 5-26 5-26 5-26 Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation 2. Select Logical Drive Logical Drive Logical Drive Logical Drive Logical Drive from the Objects Objects Objects Objects Objects sub-menu, then press <Enter>. 3. Select the logical drive to initialize from the Logical Drives Logical Drives Logical Drives Logical Drives Logical Drives sub-menu, then press <Enter>. 4. Select Initialize from the pop-up menu, then press <Enter> to start initialization.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 5-27 5-27 5-27 5-27 5-27 5. When prompted, press the <SpaceBar> to select Yes Yes Yes Yes Yes from the Initialize? Initialize? Initialize? Initialize? Initialize? dialog box, then press <Enter>. You may also press <F10> to initialize the drive without confirmation. 6. A progress bar appears on screen. If desired, press <Esc> to abort initialization. 7. When initialization is completed, press <Esc>.
5-28 5-28 5-28 5-28 5-28 Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation Rebuilding failed drives Rebuilding failed drives Rebuilding failed drives Rebuilding failed drives Rebuilding failed drives You can manually rebuild failed hard disk drives using the Rebuild Rebuild Rebuild Rebuild Rebuild o r Objects Objects Objects Objects Objects command in the Management Menu. Using the Rebuild command To rebuild a failed hard disk drive using the Rebuild Rebuild Rebuild Rebuild Rebuild command: 1. From the Management Menu, highlight Rebuild Rebuild Rebuild Rebuild Rebuild , then press <Enter>. 2. The PHYSICAL DRIVES SELECTION MENU PHYSICAL DRIVES SELECTION MENU PHYSICAL DRIVES SELECTION MENU PHYSICAL DRIVES SELECTION MENU PHYSICAL DRIVES SELECTION MENU displays the available drives connected to the SATA ports. S elect the drive you want to rebuild, then p ress <SpaceBar>.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 5-29 5-29 5-29 5-29 5-29 3. After selecting the drive to rebuild, press <F10>. The indicator for the selected drive now shows RBLD RBLD RBLD RBLD RBLD . 4. When prompted, press <Y> to to rebuild the drive. 5. When rebuild is complete, press any key to continue. Using the Objects command To rebuild a failed hard disk drive using the Objects Objects Objects Objects Objects command: 1. From the Management Menu, select Objects Objects Objects Objects Objects , then select Physical Physical Physical Physical Physical Drive Drive Drive Drive Drive from the menu. 2. Use the arrow keys to select the physical drive you want to rebuild, then p ress < Enter>. 3. Select Rebuild Rebuild Rebuild Rebuild Rebuild from the pop-up menu, then press <Enter>. 4. When prompted, press <Y> to to rebuild the drive. 5. When rebuild is complete, press any key to continue.
5-30 5-30 5-30 5-30 5-30 Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation Checking the drives for data consistency Checking the drives for data consistency Checking the drives for data consistency Checking the drives for data consistency Checking the drives for data consistency You can check and verify the accuracy of data redundancy in the selected logical drive. The utility can automatically detect and/or detect and correct any differences in data redundancy depending on the selected option in the Objects Objects Objects Objects Objects > Adapter Adapter Adapter Adapter Adapter menu. The Check Consistency command is available only for logical drives included in a RAID 1 set. Using the Check Consistency To check data consistency using the Check Consistency Check Consistency Check Consistency Check Consistency Check Consistency command: 1. From the Management Menu, select Check Consistency Check Consistency Check Consistency Check Consistency Check Consistency , then press <Enter>. 2. The screen displays the available RAID set(s) and prompts you to select the logical drive to check. Use the arrow keys to select the logical drive from the Logical Drive Logical Drive Logical Drive Logical Drive Logical Drive selection, then press <Enter>.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 5-31 5-31 5-31 5-31 5-31 3. When prompted, press the <SpaceBar> to select Yes Yes Yes Yes Yes from the Consistency Check Consistency Check Consistency Check Consistency Check Consistency Check dialog box, then press <Enter>. You may also press <F10> to check the drive consistency. A progress bar appears on screen. 4. While checking the disk consistency, press <Esc> to display the following options. • Stop - Stops the consistency check. The utility stores the percentage of disk checked, When you restart checking, it continues from the last percentage completed rather than from zero percent. • Continue - Continues the consistency check. • Abort - Aborts the consistency check. When you restart checking, it continues from zero percent. 5. When checking is complete, press any key to continue.
5-32 5-32 5-32 5-32 5-32 Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation Using the Objects command To check data consistency using the Objects Objects Objects Objects Objects command: 1. From the Management Menu, select Objects Objects Objects Objects Objects , then select Logical Logical Logical Logical Logical Drive Drive Drive Drive Drive from the menu. 2. Use the arrow keys to select the logical drive you want to check, then press < Enter>. 3. Select Check Consistency Check Consistency Check Consistency Check Consistency Check Consistency from the pop-up menu, then press <Enter>. 4. When prompted, press <Y> to to check the drive. 5. When checking is complete, press any key to continue.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 5-33 5-33 5-33 5-33 5-33 Deleting a RAID configuration Deleting a RAID configuration Deleting a RAID configuration Deleting a RAID configuration Deleting a RAID configuration To delete a RAID configuration: 1. From the Management Menu, select Configure Configure Configure Configure Configure > Clear Clear Clear Clear Clear Configuration Configuration Configuration Configuration Configuration , then press <Enter>. 2. When prompted, press the <SpaceBar> to select Yes Yes Yes Yes Y e s from the Clear Clear Clear Clear Clear Configuration? Configuration? Configuration? Configuration? Configuration? dialog box, then press <Enter>. The utility clears the current array. 3. Press any key to continue.
5-34 5-34 5-34 5-34 5-34 Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation Chapter 5: Driver installation Selecting the boot drive from a RAID set Selecting the boot drive from a RAID set Selecting the boot drive from a RAID set Selecting the boot drive from a RAID set Selecting the boot drive from a RAID set You must have created a new RAID configuration before you can select the boot drive from a RAID set. Refer to the Creating a RAID set: Using Creating a RAID set: Using Creating a RAID set: Using Creating a RAID set: Using Creating a RAID set: Using New Configuration New Configuration New Configuration New Configuration New Configuration section for details. To select the boot drive from a RAID set: 1. From the Management Menu, select Configure Configure Configure Configure Configure > Select Boot Select Boot Select Boot Select Boot Select Boot Drive Drive Drive Drive Drive , then press <Enter>. 2. When prompted, press the <SpaceBar> to select the bootable logical drive from the list, then press <Enter>. 3. The logical drive is selected as boot drive. Press any key to continue.
6 Driver installation This chapter provides information on RAID, LAN and VGA driver installation for this motherboard.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M Chapter summary 6 6.1 RAID driver installation ......................................................... 6-1 6.2 LAN driver installation .......................................................... 6-7 6.3 VGA driver installation ........................................................ 6-11
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 6-1 6-1 6-1 6-1 6-1 6.1 RAID driver installation 6.1.1 6.1.1 6.1.1 6.1.1 6.1.1 Creating a RAID driver disk Creating a RAID driver disk Creating a RAID driver disk Creating a RAID driver disk Creating a RAID driver disk A floppy disk with the RAID driver is required when installing Windows ® 2000/XP operating system on a hard disk drive that is included in a RAID set. You can create a RAID driver disk in DOS (using FreeDOS from the support CD) or in Windows ® environment. DOS DOS DOS DOS DOS To create a RAID driver disk in DOS environment: 1. Place the motherboard support CD in the optical drive. 2. Restart the computer, then enter the BIOS Setup. 3. Set the optical drive as the first boot priority to boot from the support CD. Save your changes, then exit the BIOS Setup. 4. Restart the computer. The following screen appears during POST. 5. Place a blank, high-density floppy disk to the floppy disk drive, then press the letter of your choice. The following warning message will appear: a) FreeDOS command prompt b) Create ICH7R LSI MegaRAID IDE Driver for RHEL4 Driver Disk c) Create ICH7R LSI MegaRAID IDE Driver for RHEL4 64 bit Driver Disk d) Create ICH7R LSI MegaRAID IDE Driver for SLES9 SP1 Driver Disk e) Create ICH7R LSI MegaRAID IDE Driver for SLES9 SP1 64 bit Driver Disk f) Create ICH7R LSI MegaRAID IDE Driver for SUSE93 Driver Disk g) Create ICH7R LSI MegaRAID IDE Driver for Win 32/64 bit Driver Disk h) Create ICH7R Intel Matrix Storage for Win32 driver disk i) Create ICH7R Intel Matrix Storage for Win64 driver disk j) Create LSI Logic Fusion-MPT MiniPort for Win2K 32 bit driver k) Create LSI Logic Fusion-MPT MiniPort for Win2K3 32/64 bit driver l) Create LSI Logi Fusion-MPT MiniPort for RH3.0AS driver m) Broadcom Firmware Update Please choose a ~ m:_ 6. Press any key to continue. The RAID drivers are copied to the floppy disk. 7. Eject the floppy disk, then write-protect it to prevent computer virus infection. 8. Press any key to continue. Warning!!! Bootable CD will delete all data in floppy Press a key to continue.
6-2 6-2 6-2 6-2 6-2 Chapter 6: D Chapter 6: D Chapter 6: D Chapter 6: D Chapter 6: D river installation river installation river installation river installation river installation Windows Windows Windows Windows Windows ® ® ® ® ® 2000/2003 Server 2000/2003 Server 2000/2003 Server 2000/2003 Server 2000/2003 Server To create a RAID driver disk in Windows ® 2000/2003 Server environment: 1. Restart the system from the hard disk drive, then place the system/ motherboard support CD in the optical drive. 2. Browse the contents of the support CD to locate the driver disk utility. The 32-bit OS RAID driver disk for the Intel ® ICH7R is located in: \Drivers\Chipset\ICH\Intel\Driver\Makedisk\F6flpy32 \Drivers\Chipset\ICH\Intel\Driver\Makedisk\F6flpy32 \Drivers\Chipset\ICH\Intel\Driver\Makedisk\F6flpy32 \Drivers\Chipset\ICH\Intel\Driver\Makedisk\F6flpy32 \Drivers\Chipset\ICH\Intel\Driver\Makedisk\F6flpy32 The 64-bit OS RAID driver disk for the Intel ® ICH7R is located in: \Drivers\Chipset\ICH\Intel\Driver\Makedisk\F6flpy64 \Drivers\Chipset\ICH\Intel\Driver\Makedisk\F6flpy64 \Drivers\Chipset\ICH\Intel\Driver\Makedisk\F6flpy64 \Drivers\Chipset\ICH\Intel\Driver\Makedisk\F6flpy64 \Drivers\Chipset\ICH\Intel\Driver\Makedisk\F6flpy64 3. Insert a formatted high-density floppy disk to the floppy disk drive. 4. Follow screen instructions to complete the process. 5. After creating a RAID driver disk, eject the floppy disk, then write-protect it to prevent computer virus infection.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 6-3 6-3 6-3 6-3 6-3 6.1 6.1 6.1 6.1 6.1 .2 .2 .2 .2 .2 Installing the Intel Installing the Intel Installing the Intel Installing the Intel Installing the Intel ® ICH ICH ICH ICH ICH 7 7 7 7 7 R RAID controller driver R RAID controller driver R RAID controller driver R RAID controller driver R RAID controller driver Windows Windows Windows Windows Windows ® ® ® ® ® 2000/2003 Server OS 2000/2003 Server OS 2000/2003 Server OS 2000/2003 Server OS 2000/2003 Server OS During Windows ® 2000/2003 Server OS installation To install the Intel ® ICH7R RAID controller driver when installing Windows ® 2000/2003 Server OS: 1. Boot the computer using the Windows® 2000/2003 Server installation CD. The Windows Windows Windows Windows Windows ® ® ® ® ® 2000/2003 Setup 2000/2003 Setup 2000/2003 Setup 2000/2003 Setup 2000/2003 Setup starts. 2. Press <F6> when the message “ Press F6 if you need to install Press F6 if you need to install Press F6 if you need to install Press F6 if you need to install Press F6 if you need to install a third party SCSI or RAID driver... a third party SCSI or RAID driver... a third party SCSI or RAID driver... a third party SCSI or RAID driver... a third party SCSI or RAID driver... ” appears at the bottom of the screen. 3. When prompted, press <S> to specify an additional device.
6-4 6-4 6-4 6-4 6-4 Chapter 6: D Chapter 6: D Chapter 6: D Chapter 6: D Chapter 6: D river installation river installation river installation river installation river installation 4. Insert the Intel ® ICH7R RAID driver disk you created earlier to the floppy disk drive, then press <Enter>. 5. Select the Intel(R) 82801FR SATA RAID Controller (Desktop Intel(R) 82801FR SATA RAID Controller (Desktop Intel(R) 82801FR SATA RAID Controller (Desktop Intel(R) 82801FR SATA RAID Controller (Desktop Intel(R) 82801FR SATA RAID Controller (Desktop ICH7R) ICH7R) ICH7R) ICH7R) ICH7R) from the options, then press <Enter> to select. 6. The Windows ® 2000/2003 Setup loads the RAID controller drivers from the RAID driver disk. When prompted, press <Enter> to continue installation. 7. Setup then proceeds with the OS installation. Follow screen instructions to continue.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 6-5 6-5 6-5 6-5 6-5 5. Right-click the RAID controller RAID controller RAID controller RAID controller RAID controller item, then select Properties Properties Properties Properties Properties . 6. Click the Driver Driver Driver Driver Driver tab, then click the Update Driver Update Driver Update Driver Update Driver Update Driver button. 7. The Upgrade Device Driver Wizard Upgrade Device Driver Wizard Upgrade Device Driver Wizard Upgrade Device Driver Wizard Upgrade Device Driver Wizard window appears. Click Next Next Next Next Next . 8. Insert the RAID driver disk you created earlier to the floppy disk drive. 9. Select the option “ Search for a suitable driver for my device Search for a suitable driver for my device Search for a suitable driver for my device Search for a suitable driver for my device Search for a suitable driver for my device (recommended) (recommended) (recommended) (recommended) (recommended) , then click Next Next Next Next Next . 10. The wizard searches the RAID controller drivers. When found, click Next Next Next Next Next t o install the drivers. To an existing Windows ® 2000/2003 Server OS To install the Intel ® ICH7R RAID controller driver on an existing Windows ® 2000/2003 Server OS: 1. Restart the computer, then log on with Administrator Administrator Administrator Administrator Administrator privileges. 2. Windows ® automatically detects the RAID controller and displays a New Hardware Found New Hardware Found New Hardware Found New Hardware Found New Hardware Found window. Click Cancel Cancel Cancel Cancel Cancel . 3. Right-click the My Computer My Computer My Computer My Computer My Computer icon on the Windows ® desktop , then select Properties Properties Properties Properties Properties from the menu. 4. Click the Hardware Hardware Hardware Hardware Hardware tab, then click the Device Manager Device Manager Device Manager Device Manager Device Manager button to display the list of devices installed in the system.
6-6 6-6 6-6 6-6 6-6 Chapter 6: D Chapter 6: D Chapter 6: D Chapter 6: D Chapter 6: D river installation river installation river installation river installation river installation 11. Click Finish Finish Finish Finish Finish after the driver installation is done. To verify the Intel ® ICH7R RAID controller driver installation: 1. Right-click the My Computer My Computer My Computer My Computer My Computer icon on the Windows ® desktop , then select Properties Properties Properties Properties Properties from the menu. 2. Click the Hardware Hardware Hardware Hardware Hardware tab, then click the Device Manager Device Manager Device Manager Device Manager Device Manager button. 3. Click the “ ” sign before the item IDE ATA/ATAPI controllers IDE ATA/ATAPI controllers IDE ATA/ATAPI controllers IDE ATA/ATAPI controllers IDE ATA/ATAPI controllers . The Intel(R) 82801FB Ultra ATA Storage Controllers-2652 Intel(R) 82801FB Ultra ATA Storage Controllers-2652 Intel(R) 82801FB Ultra ATA Storage Controllers-2652 Intel(R) 82801FB Ultra ATA Storage Controllers-2652 Intel(R) 82801FB Ultra ATA Storage Controllers-2652 item should appear. 4. Right-click the Intel(R) 82801FB Intel(R) 82801FB Intel(R) 82801FB Intel(R) 82801FB Intel(R) 82801FB Ultra ATA Storage Controllers- Ultra ATA Storage Controllers- Ultra ATA Storage Controllers- Ultra ATA Storage Controllers- Ultra ATA Storage Controllers- 2652 2652 2652 2652 2652 item, then select Properties Properties Properties Properties Properties from the menu. 5. Click the Driver Driver Driver Driver Driver tab, then click the Driver Details Driver Details Driver Details Driver Details Driver Details button to display the RAID controller drivers. 6. Click OK OK OK OK O K when finished.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 6-7 6-7 6-7 6-7 6-7 6.2 LAN driver installation This section provides instructions on how to install the Broadcom ® Gigabit LAN controller drivers. 6.2.1 6.2.1 6.2.1 6.2.1 6.2.1 Windows Windows Windows Windows Windows ® ® ® ® ® 2000/2003 Server 2000/2003 Server 2000/2003 Server 2000/2003 Server 2000/2003 Server To install the Broadcom ® Gigabit LAN controller driver on a Windows ® 2000/2003 Server OS: 1. Restart the computer, then log on with Administrator Administrator Administrator Administrator Administrator privileges. 2. Insert the motherboard/system support CD to the optical drive. The CD automatically displays the Drivers Drivers Drivers Drivers Drivers menu if Autorun is enabled in your computer. • Windows ® automatically detects the LAN controllers and displays a New Hardware Found New Hardware Found New Hardware Found New Hardware Found New Hardware Found window. Click Cancel Cancel Cancel Cancel Cancel t o close this window. • If Autorun Autorun Autorun Autorun Autorun i s NOT enabled in your computer, browse the contents of the support CD to locate the file ASSETUP.EXE from the BIN folder. Double-click the ASSETUP.EXE ASSETUP.EXE ASSETUP.EXE ASSETUP.EXE ASSETUP.EXE t o run the CD. 3. Click the Broadcom 5721 LAN Driver Broadcom 5721 LAN Driver Broadcom 5721 LAN Driver Broadcom 5721 LAN Driver Broadcom 5721 LAN Driver option to begin installation.
6-8 6-8 6-8 6-8 6-8 Chapter 6: D Chapter 6: D Chapter 6: D Chapter 6: D Chapter 6: D river installation river installation river installation river installation river installation 4. Click Next Next Next Next Next when the InstallShield Wizard window appears. Follow screen instructions to continue installation.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 6-9 6-9 6-9 6-9 6-9 6.2.2 6.2.2 6.2.2 6.2.2 6.2.2 Red Hat Red Hat Red Hat Red Hat Red Hat ® ® ® ® ® Linux 9.0 Linux 9.0 Linux 9.0 Linux 9.0 Linux 9.0 Follow these instructions when installing the Broadcom ® Gigabit LAN controller base driver for the Red Hat ® Linux version 5.2.x operating system. The following procedures were tested for 2.4.x kernels through 2.4.20. Installing the source RPM package Installing the source RPM package Installing the source RPM package Installing the source RPM package Installing the source RPM package To install the source RPM package: 1. Install the source RPM package: rpm -ivh bcm5700-<version>.src.rpm 2. Change the directory to the RPM path and build the binary driver for your kernel: cd /usr/src/{redhat,OpenLinux,turbo,packages,rpm ..} rpm -bb SPECS/bcm5700.spec or rpmbuild -bb SPECS/ bcm5700.spec The RPM path is different for different Linux distributions. 3. Install the newly built package (driver and man page): rpm -ivh RPMS/i386/bcm5700-<version>.i386.rpm You need the force option when installing the driver on some distributions that has an older version of the driver. For 2.2.x kernels 2.2.x kernels 2.2.x kernels 2.2.x kernels 2.2.x kernels , the driver is installed in: /lib/modules/<kernel_version>/net/bcm5700.o For 2.4.x kernels 2.4.x kernels 2.4.x kernels 2.4.x kernels 2.4.x kernels , the driver is installed in: /lib/modules/<kernel_version>/kernel/drivers/net/ bcm5700.o For 2.4.x kernels 2.4.x kernels 2.4.x kernels 2.4.x kernels 2.4.x kernels with bcm5700 driver patched in with bcm5700 driver patched in with bcm5700 driver patched in with bcm5700 driver patched in with bcm5700 driver patched in , the driver is installed in: /lib/modules/<kernel_version>/kernel/drivers/net/bcm/ bcm5700.o or or or or or /lib/modules/<kernel_version>/kernel/drivers/addon/ bcm5700/bcm5700.o 4. Load the driver: insmod bcm5700 5. Refer to Linux distribution documentation to configure the network protocol and address.
6-10 6-10 6-10 6-10 6-10 Chapter 6: D Chapter 6: D Chapter 6: D Chapter 6: D Chapter 6: D river installation river installation river installation river installation river installation Building the driver from the TAR file Building the driver from the TAR file Building the driver from the TAR file Building the driver from the TAR file Building the driver from the TAR file To build the driver from the TAR file: 1. Create a directory and extract the TAR files: tar xvzf bcm5700-<version>.tar.gz 2. Build the driver bcm5700.o as a loadable module for the running kernel: cd bcm5700-<version>/src make 3. Test the driver by loading it: insmod bcm5700.o 4. Install the driver and man page: make install See the RPM instructions on the previous page for the location of the installed driver. 5. Refer to Linux distribution documentation to configure the network protocol and address.
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M 6-11 6-11 6-11 6-11 6-11 6.3 VGA driver installation This section provides instructions on how to install the ATI ® RAGE XL Video Graphics Adapter (VGA) driver. 6.3.1 6.3.1 6.3.1 6.3.1 6.3.1 Windows Windows Windows Windows Windows ® ® ® ® ® 2000 Server 2000 Server 2000 Server 2000 Server 2000 Server You need to manually install the ATI ® RAGE XL VGA driver on a Windows ® 2000 Server operating system. To install the ATI ® RAGE XL VGA driver: 1. Restart the computer, then log on with Administrator Administrator Administrator Administrator Administrator privileges. 2. Insert the motherboard/system support CD to the optical drive. The support CD automatically displays the Drivers Drivers Drivers Drivers Drivers menu if Autorun is enabled in your computer. Windows ® automatically detects the LAN controller and displays a New New New New New Hardware Found Hardware Found Hardware Found Hardware Found Hardware Found window. Click Cancel Cancel Cancel Cancel Cancel t o close this window. 3. Click the item ATI Rage XL Display Driver ATI Rage XL Display Driver ATI Rage XL Display Driver ATI Rage XL Display Driver ATI Rage XL Display Driver from the Drivers Drivers Drivers Drivers Drivers menu. 4. The ATI ATI ATI ATI ATI Windows Windows Windows Windows Windows 2000 Driver 2000 Driver 2000 Driver 2000 Driver 2000 Driver window appears. Click Next Next Next Next Next . Follow screen instructions to complete installation.
6-12 6-12 6-12 6-12 6-12 Chapter 6: D Chapter 6: D Chapter 6: D Chapter 6: D Chapter 6: D river installation river installation river installation river installation river installation 6.3.3 6.3.3 6.3.3 6.3.3 6.3.3 Red Hat Red Hat Red Hat Red Hat Red Hat ® ® ® ® ® Linux 9.0 Linux 9.0 Linux 9.0 Linux 9.0 Linux 9.0 The Red Hat ® Linux 9.0 (2.4.x kernels) operating system automatically recognizes the ATI ® RAGE XL VGA driver during system installation. There is no need to install an additional driver(s) to support the onboard VGA. 6.3.2 6.3.2 6.3.2 6.3.2 6.3.2 Windows Windows Windows Windows Windows ® ® ® ® ® 2003 Server 2003 Server 2003 Server 2003 Server 2003 Server The Windows ® 2003 Server operating system automatically recognizes the ATI ® RAGE XL VGA driver during system installation. There is no need to install an additional driver(s) to support the onboard VGA. Verifying the VGA driver installation Verifying the VGA driver installation Verifying the VGA driver installation Verifying the VGA driver installation Verifying the VGA driver installation To verify if the ATI ® RAGE XL VGA drivers are properly installed in a Windows ® 2000/2003 Server operating system: 1. Right-click the My Computer My Computer My Computer My Computer My Computer icon on the Windows ® desktop, then select Properties Properties Properties Properties Properties from the menu. 2. Click the Hardware Hardware Hardware Hardware Hardware tab, then click the Device Manager Device Manager Device Manager Device Manager Device Manager button. 3. Click the “ ” sign before the item Display adapters Display adapters Display adapters Display adapters Display adapters . The ATI Technologies Inc. RAGE XL PCI ATI Technologies Inc. RAGE XL PCI ATI Technologies Inc. RAGE XL PCI ATI Technologies Inc. RAGE XL PCI ATI Technologies Inc. RAGE XL PCI item should appear. 4. Right-click the ATI Technologies ATI Technologies ATI Technologies ATI Technologies ATI Technologies Inc. RAGE XL PCI Inc. RAGE XL PCI Inc. RAGE XL PCI Inc. RAGE XL PCI Inc. RAGE XL PCI item, then select Properties Properties Properties Properties Properties from the menu. 5. Click the Driver Driver Driver Driver Driver tab, then click the Driver Details Driver Details Driver Details Driver Details Driver Details button to display the VGA drivers. 6. Click OK OK OK OK O K when finished.
A The appendix includes additional information that you may refer to when configuring the motherboard. Reference information
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M Appendix summary A A.1 P5MT-M block diagram ......................................................... A-1
ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M ASUS P5MT-M A-1 A-1 A-1 A-1 A-1 A.1 P5MT-M block diagram Northbridge Intel ® Mukilteo LPC-Bus 2x DDR2 533/667 DIMM Slots DMI PCI-E X8 4xDDR2 533/667 SDRAM (max. 8 GB) SMBus H/W monitors W83792D EEPROM System information SEL FRU Slot 1 PCI-E X1 BCM5721 Smithfield/Cendar Mill Processor with 800/1066MHz system bus Southbridge Intel ® ICH7R W83627EHF Keyboard Serial Port *2 Floppy Mouse Parallel Port BIOS Flash 8 Mbit MUX PCI-E X1 BCM5721 Fan *6 Voltage * PCI-E X4 X8 Slot 2 Slot 2 X8 Slot 1 2x DDR2 533/667 DIMM Slots PCI 32Bit/33MHz ATI Rage XL SATA All *4 IDE *1 USB 2.0*8 Intel ® Pentium ® Processor Extreme Edition/Intel ® Pentium ® D/Celeron ® with 800/1066 MHz system bus
A-2 A-2 A-2 A-2 A-2 Appendix A: Reference information Appendix A: Reference information Appendix A: Reference information Appendix A: Reference information Appendix A: Reference information