Asus P4B533-E User Manual
Motherboard P4B533-E
ii Checklist
iii Features
iv Safeguards
v
vi Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: ⢠This device may not cause harmful interference, and ⢠This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer â s instructions, may cause harmful interference to radio communications. However , there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ⢠Reorient or relocate the receiving antenna. ⢠Increase the separation between the equipment and receiver . ⢠Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. ⢠Consult the dealer or an experienced radio/TV technician for help. Canadian Department of Communications Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. This class B digital apparatus complies with Canadian ICES-003. The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user â s authority to operate this equipment.
vii
viii
ix
x
24 25 33 32 31 30 2 7 2 8 2 9 26 23 4 19 1 5 6 15 1 1 1 0 9 7 17 8 1 3 16 14 20 22 1 2 18 21 23
9 8 7 6 5 4 3 2 1
11 12 13 14 15 16 17 18 10
20 21 22 23 24 25 26 27 28 19
29 30 31 32 33
24.5cm (9.6in) 30.5cm (12.0in) CPU_F AN PCI1 P ANEL FLOPPY SEC_IDE PRI_IDE Intel I/O Controller Hub (ICH4) P4B533-E CHA_F AN î CR2032 3V Lithium Cell CMOS Power A TX12V TRPWR JEN COM1 P ARALLEL PORT COM2 Intel 845E Memory Controller Hub (MCH) SB_PWR FP_LINE_IN CD AUX MODEM AFP ANEL EZ_PLUG CHASSIS CLRTC FP_AUDIO BCS1 IDE_LED Accelerated Graphics Port (AGP PRO) BCS2 AGP_WARN GAME SMARTCON USBPWR_56 C-Media CMI8738 6CH Audio Controller SPDIF USBPWR_34 KBPWR OVER_VOL T SMB USB_56 A TX Power Connector Super I/O DSW2 4Mbit Firmware Hub LAN PHY ASUS ASIC with Hardware Monitor DDR DIMM1 (64/72 bit, 184-pin module) 0 1 DDR DIMM2 (64/72 bit, 184-pin module) 2 3 DDR DIMM3 (64/72 bit, 184-pin module) 4 5 Speech Controller PROMISE PDC20276 A TA133 Controller RAID_SW DSW1 USB2.0 T : USB4 B: USB3 PS/2KBMS T : Mouse B: K eyboard Socket 478 Below:Mic In Center:Line Out T op:Line In PCI2 PCI3 PCI4 PCI5 PCI6 SEC_RAID PRI_RAID IEEE1394_1 IEEE1394_2 IR_CON SPEECH USBPWR_12 PCISMB_SW1 PCISMB_SW2 PWR_F AN 1394_SW 1394 Physical Layer Chip USB2.0 T :USB2 B:USB1 T op: RJ-45 FP_LO_SWL FP_LO_SWR
P4B533-E î P4B533-E Onboard LED AGP_W ARN ON Incorrect AGP Card OFF Correct AGP Car d SB_PWR OFF Powered Off ON Standby Power
90 - 10 0
P4B533-E î P4B533-E 184-Pin DDR DIMM Sockets 80 Pins 104 Pins
P4B533-E î P4B533-E Accelerated Graphics Port (AGP PRO)
P4B533-E î P4B533-E DIP Switches ON OFF DSW2 ON OFF 1.Frequency Selectio n 2.Frequency Selectio n 3.Frequency Selectio n 4.Frequency Selectio n 5.Frequency Selectio n 6.Frequency Selectio n 1.Frequency Multiple 2.Frequency Multiple 3.Frequency Multiple 4.Frequency Multiple ON 1234 ON 123 4 5 6 DSW1 P4B533-E î P4B533-E JumperFree⢠Mode Setting JEN Jumper Fre e (Default) Jumper Mode DSW1 ON 1234 DSW2 ON 123 4 5 6 12 23
P4B533-E î P4B533-E CPU Frequency Multiple Selection DSW2 ON 1234 24.0x ON 1234 23.0x ON 1234 22.0x ON 1234 21.0x ON 1234 17.0x ON 1234 18.0x ON 1234 19.0x ON 1234 20.0x ON 1234 16.0x ON 1234 15.0x ON 1234 14.0x ON 1234 13.0x ON 1234 8.0x ON 1234 10.0x ON 1234 1 1.0x ON 1234 12.0x P4B533-E î DSW1 P4B533-E CPU External Frequency Selection CPU AGP PCI 100MHz 66MHz 33MHz ON 123 4 5 6 105MHz 70MHz 35MHz ON 123 4 5 6 109MHz 72MHz 36MHz ON 123 4 5 6 133MH z 66MH z 33MH z ON 123 4 5 6 141MHz 70MHz 35MHz ON 123 4 5 6 CPU AGP PCI 145MHz 72MHz 36MHz ON 123 4 5 6 166MHz 66MHz 33MHz ON 123 4 5 6 200MH z 66MH z 33MH z ON 123 4 5 6
P4B533-E î P4B533-E Keyboard Power Setting KBPWR 5V (Default) 1 2 5VSB 2 3 P4B533-E î OVER_VOL T P4B533-E OVER_VOL T Setting Enabl e 2 3 (Default) Disable 1 2
P4B533-E î P4B533-E USB Device W ake Up USBPWR_12 (Default) 5V 1 2 5VSB 2 3 USBPWR_56 (Default) 5V 1 2 5VSB 2 3 USBPWR_34 5V 1 2 (Default) 5VSB 2 3
P4B533-E î P4B533-E PCISMB Setting PCISMB_SW1 PCISMB_SW2 Disable Enable (Defaul t) 12 2 3 P4B533-E î P4B533-E Speaker Selector SPEECH BUZZER (Default) 12 LINEOUT 2 3
P4B533-E î P4B533-E Bass Center Setting (BASS/CENTER ) (CENTER/BASS) BCS1 BCS2 (Default) 1 2 2 3 P4B533-E î P4B533-E Internal Line Out Selector FP_LO_SWR BLOL FLOL BLOR FLOR FP_LO_SW L
P4B533-E î P4B533-E PROMISE Setting RAID_SW Enable Disabl e (Default) 12 23 P4B533-E î P4B533-E 1394HEAD Setting 1394_SW Enable Disabl e (Default) 12 23
P4B533-E î P4B533-E Clear RTC RAM CLRTC Short solder point s to Clear CMOS CR2032 3V Lithium Cell CMOS Power
P4B533-E î P4B533-E HD Activity LED TIP: If the case-mounted LED does no t light up, try reversing the 2-pin plug. IDE_LED P4B533-E î NOTE: Orient the red markings o n the floppy ribbon cable to PIN 1. P4B533-E Floppy Disk Drive Connector PIN 1 FLOPPY
P4B533-E î P4B533-E IDE Connectors NOTE: Orient the red marking s (usually zigzag) on the IDE ribbon cable to PIN 1. SEC_IDE PIN 1 PRI_IDE
P4B533-E î NOTE: Orient the red marking s (usually zigzag) on the IDE ribbon cable to PIN 1. SEC_RAID PIN 1 PRI_RAID P4B533-E RAID IDE Connectors
P4B533-E î P4B533-E Chassis Alarm Lead CHASSIS 5VSB_MB Chassis Signal GND (Default ) P4B533-E î P4B533-E SMBus Connector SMB 1 SMBCLK Ground SMBDA T A 3V FLOA TING
P4B533-E î P4B533-E A TX & Auxiliary Power Connectors A TXPWR A TX12V EZ_PLUG 3.3VDC -12.0VDC GND PS_ON# GND GND GND -5.0VDC 5.0VDC 5.0VDC PWR_OK 12.0VDC 3.3VDC 3.3VDC GND 5.0VDC GND 5.0VDC GND 5VSB 12V GND NC GND 12V DC GND 12V DC GND
P4B533-E î P4B533-E 12-V olt Fan Connectors CPU_F AN PWR_F AN CHA_F AN GND Rotation 12V GND Rotation 12V GND Rotatio n 12V P4B533-E î P4B533-E Power Supply Thermal Connecto r Ground TRPWR TRPWR
P4B533-E î P4B533-E USB 2.0 Header USB 5V LDM1 LDP1 GND NC USB 5V LDM2 LDP2 GND 15 61 0 USB_56 P4B533-E î P4B533-E Smartcard SMARTCON NC SCRFET# NC NC NC2 VCC GND SCRUI SCRRES# NC SCRCLK 1 NC SCRREST
P4B533-E î P4B533-E Infrared Module Connector Front View Back View 5V IRTX IRRX (NC ) GND 5V IRRX IRTX GND IR_CON 1 P4B533-E î P4B533-E Game Connector GAME 1 GND J2B1 J2CX MIDI_OUT J2CY J2B2 MIDI_IN GND J1B1 J1CX GND GND J1CY J1B2 GND 9 8 16
P4B533-E î P4B533-E Internal Audio Connectors MODEM Modem-In Ground Modem-Out Ground CD(Black) AUX (White ) Right Audio Channel Left Audio Channel Ground Ground P4B533-E î P4B533-E iPanel Connector 5VSB NC CHASSIS# 5 V PCIRST# GND CIRRX EXTSMI# MLED- NC BA TT NC SMBDA T A GND 3VSB IRRX IRTX NC NC NC 5V SMBCLK NC 5VSB NC 5 V GND CIRRX NC GND IRRX IRTX CIR SIR IR_CON AFP ANEL
P4B533-E î P4B533-E Digital Audio Connector SPDIF GND 5V SPDIF_IN SPDIF_OUT GND 1 P4B533-E î P4B533-E LINE_IN Connector FP_LINE_IN AGND BLINE_LIN_L ALINE_LIN_L BLINE_IN_R LINE_IN_R
P4B533-E î P4B533-E Front Panel Audio Connector FP_AUDIO BLOL MIC2 FLOR FLOL BLOR NC MICPWR 5V A AGND P4B533-E î P4B533-E IEEE-1394 Headers IEEE1394_1 IEEE1394_2 8-pin Connector Ground Ground TP A1 TP A1- TPB1- TPB1 Ground 12V 1 Ground Ground TP A2 TP A2- TPB2- TPB2 Ground 12V 1 6-pin Connector
P4B533-E î P4B533-E System Panel Connectors * Requires an A TX power supply . PLED Ground MLED PWR 5 V Keylock 5V Speaker Speaker Connector Power LED Ground 5 V Reset SW SMI Lead Message LED ExtSMI# Ground Reset Ground Ground Ground Keyboard Lock A TX Power Switch*
ASUS EZ Flash V1.00 Copyright (C) 2002, ASUSTeK COMPUTER INC. [Onboard BIOS Information] BIOS Version : ASUS P4B533-E ACPI BIOS Revision 1002 BIOS Model : P4B533-E BIOS Built Date : 04/16/02 Please Enter File Name for NEW BIOS: _ *Note: EZ Flash will copy file from A:\, Press [ESC] to reboot
[BIOS Information in File] BIOS Version: P4B533-E Boot Block WARNING! Continue to update the BIOS (Y/N)? _ Flash Memory: SST 49LF004 1. Update Main BIOS area (Y/N)? _ 2. Update Boot Block area (Y/N)? _
Disabled Enabled Willamette 1.750V , 1.775V , 1.800V , 1.750V , 1.775V , 1.800V , 1.825V , 1.850V 1.825V , 1.850V , 1.875V , 1.900V , 1.925V , 1.950V Northwood 1.500V , 1.525V , 1.550V , 1.500V , 1.525V , 1.550V , 1.575V , 1.600V , 1.625V , 1.575V , 1.600V , 1.625V , 1.650V , 1.675V , 1.700V 1,650V , 1.675V , 1.700V , 1.725V , 1.750V , 1.775V , 1.800V
TV Box
MBF astBuild (tm) Utility 1.21 (c) 1996-2001 Promise T echnology , Inc. Auto Setup . . . . . . . . . . [ 1 ] [ 1 ] View Drive Assignments . . . . [ 2 ] [ 2 ] View Array . . . . . . . . . . [ 3 ] [ 3 ] Delete Array . . . . . . . . . [ 4 ] [ 4 ] Rebuild Array. . . . . . . . . [ 5 ] [ 5 ] Controller Configuration . . . [ 6 ] [ 6 ] Press 1..6 to select Option [ESC] Exit [ Main Menu ] [ Keys Available ] MBFastTrak (tm) âÂÂLiteâ BIOS version 2.00.0.20 (c)1995-2001 Promise Technology, Inc. All Rights Reserved. No Array defined... Press <Ctrl-F> to enter FastBuild (tm) Utility Or press <ESC> key to continue booting.
MBF astBuild (tm) Utility 1.32 (c) 1996-2001 Promise T echnology , Inc. [ Keys Available ] [ Auto Setup Options Menu ] [ ] Up [ ] Down [ , ,Space] Change Option [ESC] Exit [CTRL-Y] Save [ ] Up [ ] Down [ , ,Space] Change Option [ESC] Exit [CTRL-Y] Save Mode ........................................ Spare Drive.................................. 0 Drive(s) Used in Array....................... 2 Array Disk Capacity (size in MB)............. 29299 [ Array Setup Configuration ] Stripe Optimize Array for: Performance Typical Application usage: DESKTOP
Array has been created. <Press any key to reboot> Do you want the disk image to be duplicated to another? (Yes/No) Y - Create and Duplicate N - Create Only
Do you want the disk image to be duplicated to another? (Yes/No) Y - Create and Duplicate N - Create Only Start to duplicate the image... Do you want to continue? (Yes/No) Y - Continue N - Abort
ii Checklist
iii Features
iv Safeguards
v
vi Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: ⢠This device may not cause harmful interference, and ⢠This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer â s instructions, may cause harmful interference to radio communications. However , there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ⢠Reorient or relocate the receiving antenna. ⢠Increase the separation between the equipment and receiver . ⢠Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. ⢠Consult the dealer or an experienced radio/TV technician for help. Canadian Department of Communications Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. This class B digital apparatus complies with Canadian ICES-003. The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user â s authority to operate this equipment.
vii
viii
ix
x
24 25 33 32 31 30 2 7 2 8 2 9 26 23 4 19 1 5 6 15 1 1 1 0 9 7 17 8 1 3 16 14 20 22 1 2 18 21 23
9 8 7 6 5 4 3 2 1
11 12 13 14 15 16 17 18 10
20 21 22 23 24 25 26 27 28 19
29 30 31 32 33
24.5cm (9.6in) 30.5cm (12.0in) CPU_F AN PCI1 P ANEL FLOPPY SEC_IDE PRI_IDE Intel I/O Controller Hub (ICH4) P4B533-E CHA_F AN î CR2032 3V Lithium Cell CMOS Power A TX12V TRPWR JEN COM1 P ARALLEL PORT COM2 Intel 845E Memory Controller Hub (MCH) SB_PWR FP_LINE_IN CD AUX MODEM AFP ANEL EZ_PLUG CHASSIS CLRTC FP_AUDIO BCS1 IDE_LED Accelerated Graphics Port (AGP PRO) BCS2 AGP_WARN GAME SMARTCON USBPWR_56 C-Media CMI8738 6CH Audio Controller SPDIF USBPWR_34 KBPWR OVER_VOL T SMB USB_56 A TX Power Connector Super I/O DSW2 4Mbit Firmware Hub LAN PHY ASUS ASIC with Hardware Monitor DDR DIMM1 (64/72 bit, 184-pin module) 0 1 DDR DIMM2 (64/72 bit, 184-pin module) 2 3 DDR DIMM3 (64/72 bit, 184-pin module) 4 5 Speech Controller PROMISE PDC20276 A TA133 Controller RAID_SW DSW1 USB2.0 T : USB4 B: USB3 PS/2KBMS T : Mouse B: K eyboard Socket 478 Below:Mic In Center:Line Out T op:Line In PCI2 PCI3 PCI4 PCI5 PCI6 SEC_RAID PRI_RAID IEEE1394_1 IEEE1394_2 IR_CON SPEECH USBPWR_12 PCISMB_SW1 PCISMB_SW2 PWR_F AN 1394_SW 1394 Physical Layer Chip USB2.0 T :USB2 B:USB1 T op: RJ-45 FP_LO_SWL FP_LO_SWR
P4B533-E î P4B533-E Onboard LED AGP_W ARN ON Incorrect AGP Card OFF Correct AGP Car d SB_PWR OFF Powered Off ON Standby Power
90 - 10 0
P4B533-E î P4B533-E 184-Pin DDR DIMM Sockets 80 Pins 104 Pins
P4B533-E î P4B533-E Accelerated Graphics Port (AGP PRO)
P4B533-E î P4B533-E DIP Switches ON OFF DSW2 ON OFF 1.Frequency Selectio n 2.Frequency Selectio n 3.Frequency Selectio n 4.Frequency Selectio n 5.Frequency Selectio n 6.Frequency Selectio n 1.Frequency Multiple 2.Frequency Multiple 3.Frequency Multiple 4.Frequency Multiple ON 1234 ON 123 4 5 6 DSW1 P4B533-E î P4B533-E JumperFree⢠Mode Setting JEN Jumper Fre e (Default) Jumper Mode DSW1 ON 1234 DSW2 ON 123 4 5 6 12 23
P4B533-E î P4B533-E CPU Frequency Multiple Selection DSW2 ON 1234 24.0x ON 1234 23.0x ON 1234 22.0x ON 1234 21.0x ON 1234 17.0x ON 1234 18.0x ON 1234 19.0x ON 1234 20.0x ON 1234 16.0x ON 1234 15.0x ON 1234 14.0x ON 1234 13.0x ON 1234 8.0x ON 1234 10.0x ON 1234 1 1.0x ON 1234 12.0x P4B533-E î DSW1 P4B533-E CPU External Frequency Selection CPU AGP PCI 100MHz 66MHz 33MHz ON 123 4 5 6 105MHz 70MHz 35MHz ON 123 4 5 6 109MHz 72MHz 36MHz ON 123 4 5 6 133MH z 66MH z 33MH z ON 123 4 5 6 141MHz 70MHz 35MHz ON 123 4 5 6 CPU AGP PCI 145MHz 72MHz 36MHz ON 123 4 5 6 166MHz 66MHz 33MHz ON 123 4 5 6 200MH z 66MH z 33MH z ON 123 4 5 6
P4B533-E î P4B533-E Keyboard Power Setting KBPWR 5V (Default) 1 2 5VSB 2 3 P4B533-E î OVER_VOL T P4B533-E OVER_VOL T Setting Enabl e 2 3 (Default) Disable 1 2
P4B533-E î P4B533-E USB Device W ake Up USBPWR_12 (Default) 5V 1 2 5VSB 2 3 USBPWR_56 (Default) 5V 1 2 5VSB 2 3 USBPWR_34 5V 1 2 (Default) 5VSB 2 3
P4B533-E î P4B533-E PCISMB Setting PCISMB_SW1 PCISMB_SW2 Disable Enable (Defaul t) 12 2 3 P4B533-E î P4B533-E Speaker Selector SPEECH BUZZER (Default) 12 LINEOUT 2 3
P4B533-E î P4B533-E Bass Center Setting (BASS/CENTER ) (CENTER/BASS) BCS1 BCS2 (Default) 1 2 2 3 P4B533-E î P4B533-E Internal Line Out Selector FP_LO_SWR BLOL FLOL BLOR FLOR FP_LO_SW L
P4B533-E î P4B533-E PROMISE Setting RAID_SW Enable Disabl e (Default) 12 23 P4B533-E î P4B533-E 1394HEAD Setting 1394_SW Enable Disabl e (Default) 12 23
P4B533-E î P4B533-E Clear RTC RAM CLRTC Short solder point s to Clear CMOS CR2032 3V Lithium Cell CMOS Power
P4B533-E î P4B533-E HD Activity LED TIP: If the case-mounted LED does no t light up, try reversing the 2-pin plug. IDE_LED P4B533-E î NOTE: Orient the red markings o n the floppy ribbon cable to PIN 1. P4B533-E Floppy Disk Drive Connector PIN 1 FLOPPY
P4B533-E î P4B533-E IDE Connectors NOTE: Orient the red marking s (usually zigzag) on the IDE ribbon cable to PIN 1. SEC_IDE PIN 1 PRI_IDE
P4B533-E î NOTE: Orient the red marking s (usually zigzag) on the IDE ribbon cable to PIN 1. SEC_RAID PIN 1 PRI_RAID P4B533-E RAID IDE Connectors
P4B533-E î P4B533-E Chassis Alarm Lead CHASSIS 5VSB_MB Chassis Signal GND (Default ) P4B533-E î P4B533-E SMBus Connector SMB 1 SMBCLK Ground SMBDA T A 3V FLOA TING
P4B533-E î P4B533-E A TX & Auxiliary Power Connectors A TXPWR A TX12V EZ_PLUG 3.3VDC -12.0VDC GND PS_ON# GND GND GND -5.0VDC 5.0VDC 5.0VDC PWR_OK 12.0VDC 3.3VDC 3.3VDC GND 5.0VDC GND 5.0VDC GND 5VSB 12V GND NC GND 12V DC GND 12V DC GND
P4B533-E î P4B533-E 12-V olt Fan Connectors CPU_F AN PWR_F AN CHA_F AN GND Rotation 12V GND Rotation 12V GND Rotatio n 12V P4B533-E î P4B533-E Power Supply Thermal Connecto r Ground TRPWR TRPWR
P4B533-E î P4B533-E USB 2.0 Header USB 5V LDM1 LDP1 GND NC USB 5V LDM2 LDP2 GND 15 61 0 USB_56 P4B533-E î P4B533-E Smartcard SMARTCON NC SCRFET# NC NC NC2 VCC GND SCRUI SCRRES# NC SCRCLK 1 NC SCRREST
P4B533-E î P4B533-E Infrared Module Connector Front View Back View 5V IRTX IRRX (NC ) GND 5V IRRX IRTX GND IR_CON 1 P4B533-E î P4B533-E Game Connector GAME 1 GND J2B1 J2CX MIDI_OUT J2CY J2B2 MIDI_IN GND J1B1 J1CX GND GND J1CY J1B2 GND 9 8 16
P4B533-E î P4B533-E Internal Audio Connectors MODEM Modem-In Ground Modem-Out Ground CD(Black) AUX (White ) Right Audio Channel Left Audio Channel Ground Ground P4B533-E î P4B533-E iPanel Connector 5VSB NC CHASSIS# 5 V PCIRST# GND CIRRX EXTSMI# MLED- NC BA TT NC SMBDA T A GND 3VSB IRRX IRTX NC NC NC 5V SMBCLK NC 5VSB NC 5 V GND CIRRX NC GND IRRX IRTX CIR SIR IR_CON AFP ANEL
P4B533-E î P4B533-E Digital Audio Connector SPDIF GND 5V SPDIF_IN SPDIF_OUT GND 1 P4B533-E î P4B533-E LINE_IN Connector FP_LINE_IN AGND BLINE_LIN_L ALINE_LIN_L BLINE_IN_R LINE_IN_R
P4B533-E î P4B533-E Front Panel Audio Connector FP_AUDIO BLOL MIC2 FLOR FLOL BLOR NC MICPWR 5V A AGND P4B533-E î P4B533-E IEEE-1394 Headers IEEE1394_1 IEEE1394_2 8-pin Connector Ground Ground TP A1 TP A1- TPB1- TPB1 Ground 12V 1 Ground Ground TP A2 TP A2- TPB2- TPB2 Ground 12V 1 6-pin Connector
P4B533-E î P4B533-E System Panel Connectors * Requires an A TX power supply . PLED Ground MLED PWR 5 V Keylock 5V Speaker Speaker Connector Power LED Ground 5 V Reset SW SMI Lead Message LED ExtSMI# Ground Reset Ground Ground Ground Keyboard Lock A TX Power Switch*
ASUS EZ Flash V1.00 Copyright (C) 2002, ASUSTeK COMPUTER INC. [Onboard BIOS Information] BIOS Version : ASUS P4B533-E ACPI BIOS Revision 1002 BIOS Model : P4B533-E BIOS Built Date : 04/16/02 Please Enter File Name for NEW BIOS: _ *Note: EZ Flash will copy file from A:\, Press [ESC] to reboot
[BIOS Information in File] BIOS Version: P4B533-E Boot Block WARNING! Continue to update the BIOS (Y/N)? _ Flash Memory: SST 49LF004 1. Update Main BIOS area (Y/N)? _ 2. Update Boot Block area (Y/N)? _
Disabled Enabled Willamette 1.750V , 1.775V , 1.800V , 1.750V , 1.775V , 1.800V , 1.825V , 1.850V 1.825V , 1.850V , 1.875V , 1.900V , 1.925V , 1.950V Northwood 1.500V , 1.525V , 1.550V , 1.500V , 1.525V , 1.550V , 1.575V , 1.600V , 1.625V , 1.575V , 1.600V , 1.625V , 1.650V , 1.675V , 1.700V 1,650V , 1.675V , 1.700V , 1.725V , 1.750V , 1.775V , 1.800V
TV Box
MBF astBuild (tm) Utility 1.21 (c) 1996-2001 Promise T echnology , Inc. Auto Setup . . . . . . . . . . [ 1 ] [ 1 ] View Drive Assignments . . . . [ 2 ] [ 2 ] View Array . . . . . . . . . . [ 3 ] [ 3 ] Delete Array . . . . . . . . . [ 4 ] [ 4 ] Rebuild Array. . . . . . . . . [ 5 ] [ 5 ] Controller Configuration . . . [ 6 ] [ 6 ] Press 1..6 to select Option [ESC] Exit [ Main Menu ] [ Keys Available ] MBFastTrak (tm) âÂÂLiteâ BIOS version 2.00.0.20 (c)1995-2001 Promise Technology, Inc. All Rights Reserved. No Array defined... Press <Ctrl-F> to enter FastBuild (tm) Utility Or press <ESC> key to continue booting.
MBF astBuild (tm) Utility 1.32 (c) 1996-2001 Promise T echnology , Inc. [ Keys Available ] [ Auto Setup Options Menu ] [ ] Up [ ] Down [ , ,Space] Change Option [ESC] Exit [CTRL-Y] Save [ ] Up [ ] Down [ , ,Space] Change Option [ESC] Exit [CTRL-Y] Save Mode ........................................ Spare Drive.................................. 0 Drive(s) Used in Array....................... 2 Array Disk Capacity (size in MB)............. 29299 [ Array Setup Configuration ] Stripe Optimize Array for: Performance Typical Application usage: DESKTOP
Array has been created. <Press any key to reboot> Do you want the disk image to be duplicated to another? (Yes/No) Y - Create and Duplicate N - Create Only
Do you want the disk image to be duplicated to another? (Yes/No) Y - Create and Duplicate N - Create Only Start to duplicate the image... Do you want to continue? (Yes/No) Y - Continue N - Abort