Asus Pentium III IDE RAID Server AP110 User Manual
Pentium î III IDE RAID Server î AP1 10 User â s Manual
2 Checklist Disclaimer/Copyrights No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUST eK COMPUTER INC. ( â ASUSâ ). ASUS PROVIDES THIS MANUAL âÂÂAS IS â WITHOUT W ARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED T O THE IMPLIED W ARRANTIES OR CONDITIONS OF MERCHANT ABILITY OR FITNESS FOR A P ARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECT ORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT , SPECIAL, INCIDENT AL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DA T A, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT . Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair , modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners â benefit, without intent to infringe. The product name and revision number are both printed on the product itself. Manual revisions are released for each product design represented by the digit before and after the period of the manual revision number . Manual updates are represented by the third digit in the manual revision number . For previous or updated manuals, BIOS, drivers, or product release information, contact ASUS at http://www .asus.com.tw or through any of the means indicated on the following page. SPECIFICA TIONS AND INFORMA TION CONT AINED IN THIS MANUAL ARE FURNISHED FOR INFORMA TIONAL USE ONL Y , AND ARE SUBJECT TO CHANGE A T ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THA T MA Y APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTW ARE DESCRIBED IN IT . Copyright é 2001 ASUST eK COMPUTER INC. All Rights Reserved. Product Name: AP1 10 Manual Revision: 1.00 E767 Release Date: June 2001
3 Contents Disclaimer/Copyrights ....................................................... 2 ASUS Contact Information ................................................ 6 FCC/CDC Statements ........................................................ 7 Safety Precautions ............................................................. 8 Introduction: About This Manual .......................... 9 Audience ........................................................................... 10 Contents ........................................................................... 10 Conventions ..................................................................... 1 1 References ........................................................................ 1 1 System Package Contents .............................................. 12 Chapter 1: System Overview .............................. 13 1.1 System Features ...................................................... 14 1.2 Front Panel Features ............................................... 15 1.3 Rear Panel Features ................................................ 16 1.4 Internal Features ...................................................... 17 Chapter 2: Hardware Setup ................................ 19 2.1 Remove the Front Cover ......................................... 20 Unlock the Front Panel .............................................. 20 Remove the Screws ................................................... 20 Remove the Panel ..................................................... 20 2.2 Remove the Chassis Cover .................................... 21 Remove the Screws ................................................... 21 Remove the Cover ..................................................... 21 2.3 Motherboard Placement .......................................... 22 Placement Direction ................................................... 22 Motherboard Screws .................................................. 22 2.4 Install a CPU ............................................................. 23 CPU Socket Location ................................................. 23 CPU Orientation ......................................................... 23 Unlock the CPU Socket ............................................. 24 Insert the CPU ........................................................... 24 Secure the CPU ......................................................... 25 Connect the Fan Cable .............................................. 25
4 Contents 2.5 Install System Memory ............................................ 26 DIMM Sockets Location ............................................. 26 Install a DIMM ............................................................ 26 2.6 Install a Hard Disk Drive .......................................... 27 HDD Metal Cage ........................................................ 27 Remove the HDD Cage ............................................. 27 Install the HDD ........................................................... 28 Replace the HDD Cage ............................................. 28 Connect the Cables ................................................... 29 IDE HDD Cabling ....................................................... 29 2.7 Replace the Covers ................................................. 30 Re-install the Cover ................................................... 30 Re-install the Panel .................................................... 30 Chapter 3: Powering Up ..................................... 31 3.1 Getting Started ......................................................... 32 Connect a Monitor ..................................................... 32 Connect the Power Cord ........................................... 32 Power On ................................................................... 32 Check Power Status .................................................. 32 Chapter 4: Hardware Options ............................ 33 4.1 IDE RAID Kit ............................................................. 34 IDE RAID Kit Contents ............................................... 34 HDD T ray Frame ........................................................ 35 Hot-swap HDD T ray ................................................... 35 4.2 Install a Hot-swap HDD ........................................... 36 Install HDD Tray Frame ............................................. 36 Remove HDD T ray Cover .......................................... 37 Install an IDE Drive .................................................... 38 4.3 RAID Configuration ................................................. 39 Connect IDE Cables .................................................. 39 Install a RAID Card .................................................... 39 4.4 Removing a Hot-swap HDD T ray ............................ 40 Connect Power Cables .............................................. 40 4.5 CD-ROM Drive .......................................................... 41 Remove the CD-ROM Drive ...................................... 41 Re-install the CD-ROM Drive ..................................... 42
5 Contents Appendix A: Power Supply ................................. 43 A.1 General Description ................................................. 44 A.2 Specifications .......................................................... 45 Input Characteristics .................................................. 45 Output Characteristics ............................................... 45 Over-V oltage Protection (OVP) .................................. 45 Appendix B: T roubleshooting ............................. 47 B.1 Simple Fixes ............................................................. 48
6 ASUS Contact Information ASUST eK COMPUTER INC. (Asia-Pacific) Marketing Address: 150 Li-T e Road, Peitou, T aipei, T aiwan 1 12 T elephone: 886-2-2894-3447 Fax: 886-2-2894-3449 Email: info@asus.com.tw T echnical Support T el (English): 886-2-2890-7123 T el (Chinese): 886-2-2890-71 13 Fax: 886-2-2893-7775 Email: tsd@asus.com.tw Newsgroup: news2.asus.com.tw WWW: www .asus.com.tw FTP: ftp.asus.com.tw/pub/ASUS ASUS COMPUTER INTERNA TIONAL (America) Marketing Address: 6737 Mowry Avenue, Mowry Business Center , Building 2 Newark, CA 94560, USA Fax: 1-510-608-4555 Email: info-usa@asus.com.tw T echnical Support Fax: 1-510-608-4555 BBS: 1-510-739-3774 Email: tsd@asus.com WWW: www .asus.com FTP: ftp.asus.com.tw/pub/ASUS ASUS COMPUTER GmbH (Europe) Marketing Address: Harkortstr . 25, 40880 Ratingen, BRD, Germany Fax: 49-2102-442066 Email: sales@asuscom.de (for marketing requests only) T echnical Support Hotline: MB/Others: 49-2102-9599-0 Notebook: 49-2102-9599-10 Fax: 49-2102-9599-1 1 Support (Email): www .asuscom.de/de/support (for online support) WWW: www .asuscom.de FTP: ftp.asuscom.de/pub/ASUSCOM
7 FCC/CDC Statements Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: ⢠This device may not cause harmful interference, and ⢠This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer â s instructions, may cause harmful interference to radio communications. However , there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ⢠Reorient or relocate the receiving antenna. ⢠Increase the separation between the equipment and receiver . ⢠Connect the equipment to an outlet on a circuit dif ferent from that to which the receiver is connected. ⢠Consult the dealer or an experienced radio/TV technician for help. W ARNING! The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user â s authority to operate this equipment. Canadian Department of Communications Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. This class B digital apparatus complies with Canadian ICES-003.
8 Safet y Precautions Electrical Safety Operation Safety This product is equipped with a three-wire power cable and plug for the user âÂÂs safety . Use the power cable with a properly grounded electrical outlet to avoid electrical shock. CAUTION IMPORT ANT ⢠Before installing or removing signal cables, ensure that the power cables for the system unit and all attached devices are unplugged. ⢠T o prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. ⢠When adding or removing any additional devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device. ⢠If the power supply is broken, do not try to fix it by yourself. Contact an authorized dealer . ⢠Any mechanical operation on this server must be conducted by certified or experienced engineers. ⢠Before operating the server , carefully read all the manuals included with the server package. ⢠Before using the server , make sure all cables are correctly connected and the power cables are not damaged. If any damage is detected, contact your dealer as soon as possible. ⢠T o avoid short circuits, keep paper clips, screws, and staples away from connectors, slots, sockets and circuitry . ⢠Avoid dust, humidity , and temperature extremes. Place the server on a stable surface. IMPORT ANT
9 AP1 10 Server User â s Manual Introduction About This Manual âÂÂAbout This Manualâ introduces the contents of this document. This part includes the target audience, chapter description, and conventions used. It also lists other sources of information that are not contained in this manual.
10 Introduction: About This Manual Audience Contents This manual contains the following parts: 1. Introduction: About This Manual This part introduces the contents of this document. It includes the target audience, chapter description, and conventions used. It also lists other sources of information that are not contained in this manual. 2. Chapter 1: System Overview This chapter describes the general features of the AP1 10 server . It includes sections on front panel and rear panel specifications. 3. Chapter 2: Hardware Setup This chapter lists the hardware setup procedures that you have to perform when installing system components. 4. Chapter 3: Powering Up This chapter tells how to get started with the AP1 10 server after you have installed the basic components. 5. Chapter 4: Hardware Options This chapter gives information on how to install the optional IDE RAID kit. Y ou will also find the procedure for removing and installing the CD-ROM drive in this chapter . 6. Appendix A: Power Supply Information This appendix gives information on the 250-watt switching power supply that comes with the AP1 10 server . 7. Appendix B: T roubleshooting This appendix lists the common problems that you may encounter while using the AP1 10 server . It lists the possible causes of the problems and of fers solutions. Y ou may refer to this part and try to solve simple problems before calling customer support. This installation guide is intended for system integrators, and experienced users with at least basic knowledge of configuring an entry-level server .
AP1 10 Server User â s Manual 11 Conventions Symbols T o make sure that you perform certain tasks properly , take note of the following symbols used throughout this manual. W ARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task. IMPORT ANT : Information that you MUST follow to complete a task. NOTE: T ips and information to aid in completing a task. References Refer to the following sources for additional information and for product and software updates. 1. ASUS CUV -2LSV Series Motherboard User â s Manual This manual contains detailed information about the CUV -2L V motherboard. 2. ASUS W ebsites The ASUS websites worldwide provide updated information on ASUS hardware and softare products. The ASUS websites are listed in the ASUS Contact Information on page 6. 3. Optional Documentation Y our product package may include optional documentation such as a CD-ROM manual, warranty flyers, and others that may have been added by your dealer . NOTE: These documents are not part of the standard server package.
12 Introduction: About This Manual System Package Contents The following checklist enumerates the components included in the standard system package. 1) ASUS AS-15 Chassis 2) ASUS CUV -2L V Motherboard 3) 250W A TX Power Supply 4) 50X CD-ROM Drive 5) 1.44MB Floppy Disk Drive 6) Support CD with Drivers and Utilities 7) User â s Manuals (for system and motherboard) 8) ASUS System Management Agent (ASMA) Support CD If any of the above items is missing, contact your dealer .
13 AP1 10 Server User â s Manual This chapter describes the general features of the AP1 10 server . It includes sections on front panel, rear panel, and internal features of the server . Chapter 1 System Overview
14 Chapter 1: System Overview 1.1 System Features The ASUS AP1 10 Server is a stylish tower chassis that accommodates the ASUS CUV -2L V motherboard. The server is powered by Intel î Pentium î III/Celeron⢠processor , and supports the latest I/O, audio, and video technologies through the chipsets embedded on the motherboard. Following are highlights of the server âÂÂs many features. ⢠Processor: Support for Intel Pentium III/Celeron processor running up to over 1GHz ⢠Memory: Three DIMM sockets that support Intel PC133/PC100- compliant DIMMs, NECâ s VC133-compliant Virtual Channel (VC) SDRAM, or Enhanced Memory Systemâ s High-speed DRAMs (HSDRAMs) up to 3GB ⢠System Chipset: VIA Apollo Pro133A composed of VT82C694X North Bridge that supports 133/100/66MHz Front Side Bus (FSB), and 133/100/66MHz memory bus, and VT82C686A South Bridge with PCI Super I/O integrated peripheral controller ⢠LAN Chipset: T wo Intel 82559 Fast Ethernet LAN controller that fully supports 10BASE-T/100BASE-TX ⢠VGA Chipset: A TI RAGE-XL controller with 4MB video memory ⢠Storage: Four external bays that support two optional 5.25-inch IDE hot-swap drives, one 50X CD-ROM, and 1.44MB floppy drive; internal 3.5-inch drive bays available for two additional IDE drives ⢠Expansion: Four PCI expansion slots ⢠Power Supply: 250-watt A TX power supply with a 1 15V ac/ 230V ac voltage selector switch ⢠Security: Equipped with security keylocks for chassis and hot-swap drives
AP1 10 Server User â s Manual 15 1.2 Front Panel Features The AP1 10 front panel is designed with a door on the upper part secured by a keylock. When locked, the door provides security to the hot-swap IDE drives and other internal components because neither the front panel nor the chassis cover cannot be removed. When the door is open, you can easily access the hot-swap IDE drives (if available), floppy disk drive, and CD-ROM drive. Front Panel Door Chassis Keylock Power Button Reset Button Power LED IDE HDD LED Floppy Disk Drive Hot-Swap IDE Drives (optional) CD-ROM Drive
16 Chapter 1: System Overview 1.3 Rear Panel Features The AP1 10 rear panel includes the external I/O ports. The following picture shows the cable connectors and the devices that you connect to the ports. PS/2 Mouse AC Power Parallel RJ-45 PS/2 KB Serial USB VGA V oltage Selector The switching power supply that came with the server has a voltage selector switch below the power socket. Use this switch to select the appropriate voltage according to the voltage supply in your area. If the voltage supply in your area is 100-127V , set the switch to 1 15V . If the voltage supply in your area is 200-240V , set the switch to 230V . 1 15V/ 230V V oltage Selector Setting the switch to 1 15V in a 230V environment will seriously damage the server . CAUTION
AP1 10 Server User â s Manual 17 1.4 Internal Features The standard components inside the AP1 10 server include the motherboard, power supply , floppy and CD-ROM drives, and cables. The picture below shows the standard components and the optional IDE RAID kit that consists of hot-swap drive tray sets, IDE RAID card, and IDE cables. 1. Power Supply 2. Floppy Disk Drive 3. Hot-swap Drive T rays (optional) 4. CD-ROM Drive 5. 3.5-inch Internal Device Bays 6. IDE Cables for Hot-swap Drives (optional) 7. IDE RAID Card (optional) 8. CUV -2L V Motherboard NOTE The IDE RAID kit is optional and does not come with all models. If your server includes a RAID kit, it comes already pre-installed in the chassis. 1 8 6 2 3 4 5 7
18 Chapter 1: System Overview
19 AP1 10 Server User â s Manual This chapter describes the hardware setup procedures that you have to perform when installing system components. Chapter 2 Hardware Setup
20 Chapter 2: Hardware Setup 2.1 Remove the Front Cover Follow these steps to remove the front panel. Unlock the Front Panel Insert the system key to the keylock and turn it 90 degrees counter clockwise to unlock the front panel cover . Remove the Screws Use a Phillips screwdriver to remove the two screws that secure the front panel to the main chassis. Chassis Keylock Front Panel Screws Remove the Panel 1. Close the panel door . 2. Place your hands on the upper part of the panel and pull it firmly .
AP1 10 Server User â s Manual 21 2.2 Remove the Chassis Cover Follow these steps to remove the chassis cover . Remove the Cover Slide the cover for about an inch toward the front and lift it out of the chassis. Remove the Screws Remove the screws that secure the cover to the main chassis. The locations of the screws are indicated by circles.
22 Chapter 2: Hardware Setup Placement Direction When installing the motherboard, make sure that you place it into the chassis correctly . The edge with the external ports goes to the rear part of the chassis. Motherboard Screws Place nine (9) screws in the holes indicated by circles to secure the motherboard to the chassis. Do not overtighten the screws. Doing so may damage the motherboard. 2.3 Motherboard Placement The motherboard and other internal components of the AP1 10 server are already installed as indicated in section âÂÂ1.4 Internal Featuresâ . Refer to the motherboard user âÂÂs manual for detailed technical information about the motherboard. When removing the motherboard, you need to remove the hot-swap trays and the CD-ROM drive first, because they overlap with the motherboard. Refer to Chapter 4 for the procedure to remove the drives. NOTE Rear Panel
AP1 10 Server User â s Manual 23 2.4 Install a CPU The Socket 370 on the CUV -2L V motherboard supports a Pentium III/Celeron CPU. This section tells you how to install a CPU. The following pictures show the CPU socket location on the motherboard, and the Pin 1 mark on a CPU. CPU Socket Location The CPU socket is located beside the rear panel connectors. Note the Pin 1 location on the socket. CPU Socket 370 Pin 1 CPU Orientation A CPU has a mark (usually a notch or a gold mark) on one corner to help you identify the correct orientation when inserting it to the socket. Match the marked corner of the CPU to Pin 1 on the socket. Marked Corner In most cases, when you buy a CPU, the fan heatsink is already attached to the CPU. NOTE CPU Fan Connector
24 Chapter 3: Hardware Setup 2.4 Install a CPU Unlock the CPU Socket Unlock the socket by pressing the lever sideways then lifting it up to a 90ð-100ð angle. Marked Corner Socket Pin 1 The CPU fits only in one orientation. Do not force the CPU into the socket to prevent bending the pins and damaging the CPU. If the CPU does not fit completely , check its orientation or check for bent pins. CAUTION Insert the CPU 1. Position the CPU above the socket such that its notched or marked corner matches the socket corner near the end of the lever . 2. Carefully insert the CPU into the socket until it fits in place.
AP1 10 Server User â s Manual 25 2.4 Install a CPU Secure the CPU Push down the lever to secure the CPU to the socket. The lever clicks in place indicating that the socket is locked. The fan heatsink picture above is for reference only . The fan heatsink that you purchased may not look exactly the same as shown. Refer to the documentation that comes with the CPU for more information. NOTE Connect the Fan Cable Connect the CPU fan cable to the 3-pin CPU_F AN connector on the motherboard. Fan Cable CPU_F AN Connector
26 Chapter 3: Hardware Setup 2.5 Install System Memor y DIMM Sockets Location The motherboard has three Dual Inline Memory Module (DIMM) sockets that support 3.3V SDRAM modules in 32, 64, 128, 256, 512MB, or 1GB densities. DIMM Sockets DIMM Notch Socket Break Install a DIMM 1. Unlock a DIMM socket by pressing the retaining clips outward. Align a DIMM on the socket such that the notches on the DIMM match the breaks on the socket. 2. Firmly insert the DIMM into the socket until the retaining clips snap back in place and the DIMM is properly seated. Installed DIMM DIMMs are keyed with notches so that they fit in only one direction. DO NOT force a DIMM into a socket to avoid damaging the DIMM. CAUTION
AP1 10 Server User â s Manual 27 2.6 Install a Hard Disk Drive The AP1 10 server comes with drive bays for internal hard disk drives. Y ou can install up to two internal hard disk drives. HDD Metal Cage The HDD metal cage is located right under the CD-ROM drive bay . Y ou have to remove the cage from the chassis to conveniently install a hard disk drive. Remove the HDD Cage 1. Remove the screws (indicated by circles) that secure the HDD cage to the front of the chassis. 2. Remove the screw on the side of the HDD cage. 3. Pull the HDD cage out of the chassis. Cage Screw Cage Screw HDD Metal Cage
28 Chapter 2: Hardware Setup 2.6 Install a Hard Disk Drive Install the HDD 1. Insert the HDD into the cage (label side up) until the holes on the sides align. 2. Secure the HDD with four screws (two on each side). Replace the HDD Cage 1. Carefully insert the HDD cage back into the chassis until it fits in place. 2. Secure the cage with the screws you removed earlier .
AP1 10 Server User â s Manual 29 Connect the Cables 1. Connect one end of the IDE cable to the IDE connector at the back of the drive, matching the red stripe on the cable with Pin 1 on the IDE connector . 2. Connect a power cable (plug marked P3 or P4) to the power connector at the back of the drive. 3. Connect the other end of the IDE cable to the primary IDE connector (blue connector) on the motherboard. IDE Cable Red Stripe to Pin 1 Power Cable (P3 or P4) 2.6 Install a Hard Disk Drive IDE HDD Cabling The picture on the left shows an installed HDD. Primary IDE Connector
30 Chapter 2: Hardware Setup 2.7 Replace the Covers Re-install the Panel 1. Align the bottom edge of the panel to the chassis. 2. Firmly push the panel with both hands until it fits in place. 3. Open the panel door . 4. Secure the panel with the two screws that you removed earlier . 5. Lock the front panel with the system key . Re-install the Cover 1. Place the cover from the top of the chassis, leaving about an inch from the rear edge. 2. Slide the cover toward the rear panel until it fits in place. NOTE If you are installing optional components such as the IDE RAID kit, proceed to Chapter 4 before replacing the covers.
31 AP1 10 Server User â s Manual This chapter tells how to get started with the AP1 10 server . Powering up the server basically includes connecting the cables and turning power on. Chapter 3 Powering Up
32 Chapter 3: Powering Up 3.1 Getting Star ted Make sure that you have completed the basic system installations in Chapter 2, then follow these steps to start up the server . Connect a Monitor Connect a monitor by plugging hte monitor cable to the video port (blue port) on the server rear panel. Connect the Power Cord 1. Adjust the voltage selector to the correct voltage in your area. 2. Connect a power cord to the power connector on the rear panel. 3. Plug the power cord to a grounded wall socket. Power On T urn on the server by pressing the power button on the front panel. Check Power Status After turning on the power , the power LED lights up. If it doesnâÂÂt, check the power connection. Video Port Power Button Power LED Power Connector V oltage Selector
33 AP1 10 Server User â s Manual This chapter tells how to install the optional IDE RAID kit. Chapter 4 Hardware Options
34 Chapter 4: Hardware Options 4.1 IDE RAID Kit The AP1 10 server supports a maximum of four hard disk drives, two external and two internal. The external HDD bays are available for an IDE RAID configuration using the optional IDE RAID Kit. This chapter tells about external HDD installation using the IDE RAID kit. Refer to Chapter 3 for instructions on internal HDD installation. IDE RAID Kit Contents NOTE The IDE RAID kit is optional and does not come with all models. If your server includes a RAID kit, it comes already pre-installed in the chassis. Hot-swap HDD T ray Sets RAID Card Security Keys Screws A T A/100 IDE Cables NOTE The IDE RAID kit also includes a diskette that contains the IDE drivers and a RAID card user â s manual.
AP1 10 Server User â s Manual 35 HDD T ray Frame The HDD tray frame is a separate unit that holds the hot-swap drive tray . A 64-pin male connector is found on the rear of the frame. This connector matches the 64-pin female connector at the back of the hot-swap drive tray . The back of the tray frame is an HDD fan, an IDE connector (male), and a power connector . HDD Fan Hot-swap HDD T ray The hot-swap drive tray is an enclosure that holds the HDD. The drive tray interior includes an IDE cable and a power cable. Power Connector IDE Connector 4.1 IDE RAID Kit 64-pin Male Connector Hot-swap HDD T ray with Cover IDE Cable Power Cable 64-pin Female Connector
36 Chapter 4: Hardware Options 4.2 Install a Hot-swap HDD Install HDD T ray Frame 1. Insert an HDD tray frame into one external drive bay as shown. 3. Follow steps 1 and 2 to install the second HDD tray frame. The picture on the right shows the two installed HDD tray frames. 2. Secure the frame with four screws (two on each side). NOTE: Align the front screws with the holes labeled 1. Frame Screw Align with Hole 1
AP1 10 Server User â s Manual 37 4.2 Install Hot-swap HDD Remove HDD T ray Cover The hot-swap drive tray has a cover that you have to remove before you can install a hard disk. T o remove the tray cover: 1. Pull up the lever on the front of the tray . Doing this action slides the tray cover backward about a quarter of an inch. 2. Following the direction of the arrow in the picture, use a finger to flip out the metal latch on the front corner of the cover to disengage it from the tray . 3. Slide the cover all the way back to remove it. T ray Lever Metal Latch
38 Chapter 4: Hardware Options 4.2 Install Hot-swap HDD Install an IDE Drive 1. Connect the IDE cable to the IDE connector at the back of the drive. 2. Connect the power cable to the power connector at the back of the drive. 3. Carefully place the drive into the tray until it fits in place. 4. Secure the drive with four screws (two on each side). 5. Align the tray cover to the rails at the back of the tray , then slide the cover forward until the metal latch clicks in place. 6. Insert the hot-swap drive tray into the bay until it is flushed to the front panel. 7. Lock the hot-swap drive tray with the security key to prevent unauthorized access. 8. Do steps 1 to 7 to install the other hot-swap drive. Installed Hot-Swap Drive T rays IDE Cable Power Cable
AP1 10 Server User â s Manual 39 4.3 RAID Configuration Install a RAID Card 1. Remove the cover opposite the PCI1 expansion slot. 2. Carefully insert the golden fingers of the RAID card into the slot until the card is properly seated. RAID Card Connect IDE Cables 1. Connect one end of an IDE cable to the IDE1 connector on the RAID card, and the other end to the back of a hot-swap drive frame. 2. Connect one end of the second IDE cable to the IDE2 connector on the RAID card, and the other end to the second hot-swap drive frame. This section presents only the physical hardware connections of the RAID card, hot-swap HDDs, and IDE and power cables. For detailed instructions on RAID configuration, refer to the user âÂÂs manual that came with the IDE RAID kit. IDE2 Connector IDE1 Connector IMPORT ANT Use two separate IDE cables for IDE1 and IDE2 connections.
40 Chapter 4: Hardware Options 4.3 RAID Configuration Connect Power Cables Connect the power cables, with plugs labeled P5 and P6, to the power connectors at the back of the hot-swap drive frames. 4.4 Removing a Hot-swap HDD Tray In the future, you might need to remove the drive tray and replace a hot-swap HDD. T o remove a hot-swap drive tray: 1. Unlock the drive tray you desire to remove. 2. Lift up the tray handle. 3. Pull the tray out of the bay . 4. Refer to section 4.2 for instructions on installing a hot- swap HDD. Power Cables
AP1 10 Server User â s Manual 41 4.5 CD-ROM Drive The server comes with the CD-ROM drive already installed. This section tells how to remove and re-install the CD-ROM drive. Y ou will need to remove the CD-ROM drive for either one of the following reasons: 1. Y ou need to replace the drive 2. Y ou need to remove the motherboard. The CD-ROM drive overlaps with the top right corner of the motherboard, so you can not get it out without moving the drive outward. Remove the CD-ROM Drive 1. Disconnect the power and IDE cables from the drive. 2. Remove the four screws (two on each side) that secure the drive to the chassis. 3. Carefully pull the drive out of the chassis. Power and IDE Cables CD-ROM Screws If you are doing the above procedure for the purpose of removing the motherboard, you do not have to completely remove the drive from the chassis. Simply pull out the drive for about an inch, or until you can access the motherboard. In this instance, you also have to pull out the hot-swap drive trays because they , too, overlap with the motherboard. NOTE T op Right Corner of the Motherboard Hot-swap HHD T rays and CD-ROM Drive Pulled Out
42 Chapter 4: Hardware Options 4.5 CD-ROM Drive Re-install the CD-ROM Drive 1. Align the CD-ROM drive to its bay and carefully push it inward until it is flushed to the front panel. 2. Secure the drive with the screws that you removed earlier (two on each side). NOTE: Align the front screw with the hole labeled 1. 3. Connect the IDE cable to the IDE connector at the back of the drive, matching the red pin stripe on the cable with Pin1 on the IDE connector . 4. Connect the power cable labeled P2 to the power connector at the back of the drive. Align with Hole 1 CD-ROM Screws IDE Cable Power Cable (P2) Red Stripe to Pin 1
43 AP1 10 Server User â s Manual This appendix gives information on the 250-watt switching power supply that comes with the AP1 10 server . Appendix A Power Supply
44 Appendix A: Power Supply A .1 General Description The server comes with a 250W A TX power supply with universal AC input that includes PFC and A TX-compliant output cables and connectors. The power supply has an internal cooling fan. The power supply has seven plugs labeled P1 to P7. The picture below shows the specific device assignments for the plugs. P2 P4 P3 P1 P5 P6 P7 P1. Motherboard A TX Power P2. CD-ROM Drive P3. Internal HDD P4. Internal HDD P5. Hot-swap HDD P6. Hot-swap HDD P7. Floppy Disk Drive
AP1 10 Server User â s Manual 45 Input Characteristics A .2 Specifications Output Characteristics Over-V oltage Protection (OVP) Input V oltage Range Min Nom Max Range 1 90V 1 15V 135V Range 2 180V 230V 265V Input Frequency Range 47 Hz to 63 Hz Maximum Input ac Current 9A max at 1 15V ac 5A max. at 230V ac, maximum load Inrush Current 70A max. at 1 15V ac, full load cold start at 25ðC Efficiency 68% min. at nominal input, maximum load Output Load Range Regulation Ripple V oltage Min Max Min Max Max 5V 1.5A 25.0A -5% 5% 50mV p-p 12V 0.2A 8.0A -5% 5% 120mV p-p -12V 0A 0.8A -10% 10% 150mV p-p -5V 0A 0.5A -5% 5% 100mV p-p 5Vsb 0A 2.0A -5% 5% 100mV p-p 3V3 0A 14.0A -5% 5% 50mV p-p Output V oltage Maximum V oltage 5V 6.5V 12V 15.6V 3.3V 4.3V NOTE The power supply will shut down and latch off for shorting 5V , 12V , -12V , -5V , or 3.3V . By shorting 5Vsb, the power supply can latch down or automatically recover when the fault condition is removed.
46 Appendix A: Power Supply
47 AP1 10 Server User â s Manual This appendix lists the common problems that you may encounter while using the AP1 10 server . It lists the possible causes of the problems and offers solutions. Y ou may refer to this part and try to solve simple problems before calling customer support. Appendix B T roubleshooting
48 Appendix B: T roubleshooting B.1 Simple Fixes The power LED on the server and/or the monitor do not light up NOTE Some problems that you may encounter are not due to defects on the system or the components. These problems only requires simple troubleshooting actions that you can perform by yourself. 1. Make sure that the 1 15V/230V voltage selector switch is set to the correct voltage supply in your area. 2. Check the power cable connection on the system rear panel if properly connected. 3. Make sure that the power cables are connected to a grounded power outlet. 4. Press the power button to make sure that the system is turned on. Problem Action The keyboard does not work Check the keyboard cable if properly connected to the keyboard port. The mouse does not work Check the mouse cable if properly connected to the mouse port. The system does not perform power-on self tests (POST) after it was turned on 1. Check the memory modules and make sure you installed the DIMMs the system supports. 2. Make sure that the DIMMs are properly installed on the sockets.
AP1 10 Server User â s Manual 49 The system continuously beeps after it was turned on 1. Check the memory modules and make sure you installed the DIMMs the system supports. 2. Make sure that the DIMMs are properly installed on the sockets. The message âÂÂNon-system disk or disk error â appears Check if bootable HDD is active. RAID HDD is only detected as 1024MB 1. Boot from DOS/Win9x floppy disk. 2. Run FDISK utility to delete all partition 3. Reboot the system and run FDISK /MBR. RAID HDD shows incorrect size when you execute FDISK If the RAID set is larger than 64GB, try using SPFDISK utility to solve the problem. PCI-IDE RAID controller does not detect HDDs Press F6 and load the PCI-IDE RAID driver when booting from Windows NT/200 OS CD. Onboard IDE HDD is unstable Install the VIA utility drivers from the ASUS support CD. Network connection not available 1. Make sure the network cable is connector the RJ-45 port on the rear panel. 2. Make sure that you have installed the network drivers from the motherboard support CD. Problem Action
50 Appendix B: T roubleshooting
2 Checklist Disclaimer/Copyrights No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUST eK COMPUTER INC. ( â ASUSâ ). ASUS PROVIDES THIS MANUAL âÂÂAS IS â WITHOUT W ARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED T O THE IMPLIED W ARRANTIES OR CONDITIONS OF MERCHANT ABILITY OR FITNESS FOR A P ARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECT ORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT , SPECIAL, INCIDENT AL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DA T A, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT . Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair , modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners â benefit, without intent to infringe. The product name and revision number are both printed on the product itself. Manual revisions are released for each product design represented by the digit before and after the period of the manual revision number . Manual updates are represented by the third digit in the manual revision number . For previous or updated manuals, BIOS, drivers, or product release information, contact ASUS at http://www .asus.com.tw or through any of the means indicated on the following page. SPECIFICA TIONS AND INFORMA TION CONT AINED IN THIS MANUAL ARE FURNISHED FOR INFORMA TIONAL USE ONL Y , AND ARE SUBJECT TO CHANGE A T ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THA T MA Y APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTW ARE DESCRIBED IN IT . Copyright é 2001 ASUST eK COMPUTER INC. All Rights Reserved. Product Name: AP1 10 Manual Revision: 1.00 E767 Release Date: June 2001
3 Contents Disclaimer/Copyrights ....................................................... 2 ASUS Contact Information ................................................ 6 FCC/CDC Statements ........................................................ 7 Safety Precautions ............................................................. 8 Introduction: About This Manual .......................... 9 Audience ........................................................................... 10 Contents ........................................................................... 10 Conventions ..................................................................... 1 1 References ........................................................................ 1 1 System Package Contents .............................................. 12 Chapter 1: System Overview .............................. 13 1.1 System Features ...................................................... 14 1.2 Front Panel Features ............................................... 15 1.3 Rear Panel Features ................................................ 16 1.4 Internal Features ...................................................... 17 Chapter 2: Hardware Setup ................................ 19 2.1 Remove the Front Cover ......................................... 20 Unlock the Front Panel .............................................. 20 Remove the Screws ................................................... 20 Remove the Panel ..................................................... 20 2.2 Remove the Chassis Cover .................................... 21 Remove the Screws ................................................... 21 Remove the Cover ..................................................... 21 2.3 Motherboard Placement .......................................... 22 Placement Direction ................................................... 22 Motherboard Screws .................................................. 22 2.4 Install a CPU ............................................................. 23 CPU Socket Location ................................................. 23 CPU Orientation ......................................................... 23 Unlock the CPU Socket ............................................. 24 Insert the CPU ........................................................... 24 Secure the CPU ......................................................... 25 Connect the Fan Cable .............................................. 25
4 Contents 2.5 Install System Memory ............................................ 26 DIMM Sockets Location ............................................. 26 Install a DIMM ............................................................ 26 2.6 Install a Hard Disk Drive .......................................... 27 HDD Metal Cage ........................................................ 27 Remove the HDD Cage ............................................. 27 Install the HDD ........................................................... 28 Replace the HDD Cage ............................................. 28 Connect the Cables ................................................... 29 IDE HDD Cabling ....................................................... 29 2.7 Replace the Covers ................................................. 30 Re-install the Cover ................................................... 30 Re-install the Panel .................................................... 30 Chapter 3: Powering Up ..................................... 31 3.1 Getting Started ......................................................... 32 Connect a Monitor ..................................................... 32 Connect the Power Cord ........................................... 32 Power On ................................................................... 32 Check Power Status .................................................. 32 Chapter 4: Hardware Options ............................ 33 4.1 IDE RAID Kit ............................................................. 34 IDE RAID Kit Contents ............................................... 34 HDD T ray Frame ........................................................ 35 Hot-swap HDD T ray ................................................... 35 4.2 Install a Hot-swap HDD ........................................... 36 Install HDD Tray Frame ............................................. 36 Remove HDD T ray Cover .......................................... 37 Install an IDE Drive .................................................... 38 4.3 RAID Configuration ................................................. 39 Connect IDE Cables .................................................. 39 Install a RAID Card .................................................... 39 4.4 Removing a Hot-swap HDD T ray ............................ 40 Connect Power Cables .............................................. 40 4.5 CD-ROM Drive .......................................................... 41 Remove the CD-ROM Drive ...................................... 41 Re-install the CD-ROM Drive ..................................... 42
5 Contents Appendix A: Power Supply ................................. 43 A.1 General Description ................................................. 44 A.2 Specifications .......................................................... 45 Input Characteristics .................................................. 45 Output Characteristics ............................................... 45 Over-V oltage Protection (OVP) .................................. 45 Appendix B: T roubleshooting ............................. 47 B.1 Simple Fixes ............................................................. 48
6 ASUS Contact Information ASUST eK COMPUTER INC. (Asia-Pacific) Marketing Address: 150 Li-T e Road, Peitou, T aipei, T aiwan 1 12 T elephone: 886-2-2894-3447 Fax: 886-2-2894-3449 Email: info@asus.com.tw T echnical Support T el (English): 886-2-2890-7123 T el (Chinese): 886-2-2890-71 13 Fax: 886-2-2893-7775 Email: tsd@asus.com.tw Newsgroup: news2.asus.com.tw WWW: www .asus.com.tw FTP: ftp.asus.com.tw/pub/ASUS ASUS COMPUTER INTERNA TIONAL (America) Marketing Address: 6737 Mowry Avenue, Mowry Business Center , Building 2 Newark, CA 94560, USA Fax: 1-510-608-4555 Email: info-usa@asus.com.tw T echnical Support Fax: 1-510-608-4555 BBS: 1-510-739-3774 Email: tsd@asus.com WWW: www .asus.com FTP: ftp.asus.com.tw/pub/ASUS ASUS COMPUTER GmbH (Europe) Marketing Address: Harkortstr . 25, 40880 Ratingen, BRD, Germany Fax: 49-2102-442066 Email: sales@asuscom.de (for marketing requests only) T echnical Support Hotline: MB/Others: 49-2102-9599-0 Notebook: 49-2102-9599-10 Fax: 49-2102-9599-1 1 Support (Email): www .asuscom.de/de/support (for online support) WWW: www .asuscom.de FTP: ftp.asuscom.de/pub/ASUSCOM
7 FCC/CDC Statements Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: ⢠This device may not cause harmful interference, and ⢠This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer â s instructions, may cause harmful interference to radio communications. However , there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ⢠Reorient or relocate the receiving antenna. ⢠Increase the separation between the equipment and receiver . ⢠Connect the equipment to an outlet on a circuit dif ferent from that to which the receiver is connected. ⢠Consult the dealer or an experienced radio/TV technician for help. W ARNING! The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user â s authority to operate this equipment. Canadian Department of Communications Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. This class B digital apparatus complies with Canadian ICES-003.
8 Safet y Precautions Electrical Safety Operation Safety This product is equipped with a three-wire power cable and plug for the user âÂÂs safety . Use the power cable with a properly grounded electrical outlet to avoid electrical shock. CAUTION IMPORT ANT ⢠Before installing or removing signal cables, ensure that the power cables for the system unit and all attached devices are unplugged. ⢠T o prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. ⢠When adding or removing any additional devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device. ⢠If the power supply is broken, do not try to fix it by yourself. Contact an authorized dealer . ⢠Any mechanical operation on this server must be conducted by certified or experienced engineers. ⢠Before operating the server , carefully read all the manuals included with the server package. ⢠Before using the server , make sure all cables are correctly connected and the power cables are not damaged. If any damage is detected, contact your dealer as soon as possible. ⢠T o avoid short circuits, keep paper clips, screws, and staples away from connectors, slots, sockets and circuitry . ⢠Avoid dust, humidity , and temperature extremes. Place the server on a stable surface. IMPORT ANT
9 AP1 10 Server User â s Manual Introduction About This Manual âÂÂAbout This Manualâ introduces the contents of this document. This part includes the target audience, chapter description, and conventions used. It also lists other sources of information that are not contained in this manual.
10 Introduction: About This Manual Audience Contents This manual contains the following parts: 1. Introduction: About This Manual This part introduces the contents of this document. It includes the target audience, chapter description, and conventions used. It also lists other sources of information that are not contained in this manual. 2. Chapter 1: System Overview This chapter describes the general features of the AP1 10 server . It includes sections on front panel and rear panel specifications. 3. Chapter 2: Hardware Setup This chapter lists the hardware setup procedures that you have to perform when installing system components. 4. Chapter 3: Powering Up This chapter tells how to get started with the AP1 10 server after you have installed the basic components. 5. Chapter 4: Hardware Options This chapter gives information on how to install the optional IDE RAID kit. Y ou will also find the procedure for removing and installing the CD-ROM drive in this chapter . 6. Appendix A: Power Supply Information This appendix gives information on the 250-watt switching power supply that comes with the AP1 10 server . 7. Appendix B: T roubleshooting This appendix lists the common problems that you may encounter while using the AP1 10 server . It lists the possible causes of the problems and of fers solutions. Y ou may refer to this part and try to solve simple problems before calling customer support. This installation guide is intended for system integrators, and experienced users with at least basic knowledge of configuring an entry-level server .
AP1 10 Server User â s Manual 11 Conventions Symbols T o make sure that you perform certain tasks properly , take note of the following symbols used throughout this manual. W ARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task. IMPORT ANT : Information that you MUST follow to complete a task. NOTE: T ips and information to aid in completing a task. References Refer to the following sources for additional information and for product and software updates. 1. ASUS CUV -2LSV Series Motherboard User â s Manual This manual contains detailed information about the CUV -2L V motherboard. 2. ASUS W ebsites The ASUS websites worldwide provide updated information on ASUS hardware and softare products. The ASUS websites are listed in the ASUS Contact Information on page 6. 3. Optional Documentation Y our product package may include optional documentation such as a CD-ROM manual, warranty flyers, and others that may have been added by your dealer . NOTE: These documents are not part of the standard server package.
12 Introduction: About This Manual System Package Contents The following checklist enumerates the components included in the standard system package. 1) ASUS AS-15 Chassis 2) ASUS CUV -2L V Motherboard 3) 250W A TX Power Supply 4) 50X CD-ROM Drive 5) 1.44MB Floppy Disk Drive 6) Support CD with Drivers and Utilities 7) User â s Manuals (for system and motherboard) 8) ASUS System Management Agent (ASMA) Support CD If any of the above items is missing, contact your dealer .
13 AP1 10 Server User â s Manual This chapter describes the general features of the AP1 10 server . It includes sections on front panel, rear panel, and internal features of the server . Chapter 1 System Overview
14 Chapter 1: System Overview 1.1 System Features The ASUS AP1 10 Server is a stylish tower chassis that accommodates the ASUS CUV -2L V motherboard. The server is powered by Intel î Pentium î III/Celeron⢠processor , and supports the latest I/O, audio, and video technologies through the chipsets embedded on the motherboard. Following are highlights of the server âÂÂs many features. ⢠Processor: Support for Intel Pentium III/Celeron processor running up to over 1GHz ⢠Memory: Three DIMM sockets that support Intel PC133/PC100- compliant DIMMs, NECâ s VC133-compliant Virtual Channel (VC) SDRAM, or Enhanced Memory Systemâ s High-speed DRAMs (HSDRAMs) up to 3GB ⢠System Chipset: VIA Apollo Pro133A composed of VT82C694X North Bridge that supports 133/100/66MHz Front Side Bus (FSB), and 133/100/66MHz memory bus, and VT82C686A South Bridge with PCI Super I/O integrated peripheral controller ⢠LAN Chipset: T wo Intel 82559 Fast Ethernet LAN controller that fully supports 10BASE-T/100BASE-TX ⢠VGA Chipset: A TI RAGE-XL controller with 4MB video memory ⢠Storage: Four external bays that support two optional 5.25-inch IDE hot-swap drives, one 50X CD-ROM, and 1.44MB floppy drive; internal 3.5-inch drive bays available for two additional IDE drives ⢠Expansion: Four PCI expansion slots ⢠Power Supply: 250-watt A TX power supply with a 1 15V ac/ 230V ac voltage selector switch ⢠Security: Equipped with security keylocks for chassis and hot-swap drives
AP1 10 Server User â s Manual 15 1.2 Front Panel Features The AP1 10 front panel is designed with a door on the upper part secured by a keylock. When locked, the door provides security to the hot-swap IDE drives and other internal components because neither the front panel nor the chassis cover cannot be removed. When the door is open, you can easily access the hot-swap IDE drives (if available), floppy disk drive, and CD-ROM drive. Front Panel Door Chassis Keylock Power Button Reset Button Power LED IDE HDD LED Floppy Disk Drive Hot-Swap IDE Drives (optional) CD-ROM Drive
16 Chapter 1: System Overview 1.3 Rear Panel Features The AP1 10 rear panel includes the external I/O ports. The following picture shows the cable connectors and the devices that you connect to the ports. PS/2 Mouse AC Power Parallel RJ-45 PS/2 KB Serial USB VGA V oltage Selector The switching power supply that came with the server has a voltage selector switch below the power socket. Use this switch to select the appropriate voltage according to the voltage supply in your area. If the voltage supply in your area is 100-127V , set the switch to 1 15V . If the voltage supply in your area is 200-240V , set the switch to 230V . 1 15V/ 230V V oltage Selector Setting the switch to 1 15V in a 230V environment will seriously damage the server . CAUTION
AP1 10 Server User â s Manual 17 1.4 Internal Features The standard components inside the AP1 10 server include the motherboard, power supply , floppy and CD-ROM drives, and cables. The picture below shows the standard components and the optional IDE RAID kit that consists of hot-swap drive tray sets, IDE RAID card, and IDE cables. 1. Power Supply 2. Floppy Disk Drive 3. Hot-swap Drive T rays (optional) 4. CD-ROM Drive 5. 3.5-inch Internal Device Bays 6. IDE Cables for Hot-swap Drives (optional) 7. IDE RAID Card (optional) 8. CUV -2L V Motherboard NOTE The IDE RAID kit is optional and does not come with all models. If your server includes a RAID kit, it comes already pre-installed in the chassis. 1 8 6 2 3 4 5 7
18 Chapter 1: System Overview
19 AP1 10 Server User â s Manual This chapter describes the hardware setup procedures that you have to perform when installing system components. Chapter 2 Hardware Setup
20 Chapter 2: Hardware Setup 2.1 Remove the Front Cover Follow these steps to remove the front panel. Unlock the Front Panel Insert the system key to the keylock and turn it 90 degrees counter clockwise to unlock the front panel cover . Remove the Screws Use a Phillips screwdriver to remove the two screws that secure the front panel to the main chassis. Chassis Keylock Front Panel Screws Remove the Panel 1. Close the panel door . 2. Place your hands on the upper part of the panel and pull it firmly .
AP1 10 Server User â s Manual 21 2.2 Remove the Chassis Cover Follow these steps to remove the chassis cover . Remove the Cover Slide the cover for about an inch toward the front and lift it out of the chassis. Remove the Screws Remove the screws that secure the cover to the main chassis. The locations of the screws are indicated by circles.
22 Chapter 2: Hardware Setup Placement Direction When installing the motherboard, make sure that you place it into the chassis correctly . The edge with the external ports goes to the rear part of the chassis. Motherboard Screws Place nine (9) screws in the holes indicated by circles to secure the motherboard to the chassis. Do not overtighten the screws. Doing so may damage the motherboard. 2.3 Motherboard Placement The motherboard and other internal components of the AP1 10 server are already installed as indicated in section âÂÂ1.4 Internal Featuresâ . Refer to the motherboard user âÂÂs manual for detailed technical information about the motherboard. When removing the motherboard, you need to remove the hot-swap trays and the CD-ROM drive first, because they overlap with the motherboard. Refer to Chapter 4 for the procedure to remove the drives. NOTE Rear Panel
AP1 10 Server User â s Manual 23 2.4 Install a CPU The Socket 370 on the CUV -2L V motherboard supports a Pentium III/Celeron CPU. This section tells you how to install a CPU. The following pictures show the CPU socket location on the motherboard, and the Pin 1 mark on a CPU. CPU Socket Location The CPU socket is located beside the rear panel connectors. Note the Pin 1 location on the socket. CPU Socket 370 Pin 1 CPU Orientation A CPU has a mark (usually a notch or a gold mark) on one corner to help you identify the correct orientation when inserting it to the socket. Match the marked corner of the CPU to Pin 1 on the socket. Marked Corner In most cases, when you buy a CPU, the fan heatsink is already attached to the CPU. NOTE CPU Fan Connector
24 Chapter 3: Hardware Setup 2.4 Install a CPU Unlock the CPU Socket Unlock the socket by pressing the lever sideways then lifting it up to a 90ð-100ð angle. Marked Corner Socket Pin 1 The CPU fits only in one orientation. Do not force the CPU into the socket to prevent bending the pins and damaging the CPU. If the CPU does not fit completely , check its orientation or check for bent pins. CAUTION Insert the CPU 1. Position the CPU above the socket such that its notched or marked corner matches the socket corner near the end of the lever . 2. Carefully insert the CPU into the socket until it fits in place.
AP1 10 Server User â s Manual 25 2.4 Install a CPU Secure the CPU Push down the lever to secure the CPU to the socket. The lever clicks in place indicating that the socket is locked. The fan heatsink picture above is for reference only . The fan heatsink that you purchased may not look exactly the same as shown. Refer to the documentation that comes with the CPU for more information. NOTE Connect the Fan Cable Connect the CPU fan cable to the 3-pin CPU_F AN connector on the motherboard. Fan Cable CPU_F AN Connector
26 Chapter 3: Hardware Setup 2.5 Install System Memor y DIMM Sockets Location The motherboard has three Dual Inline Memory Module (DIMM) sockets that support 3.3V SDRAM modules in 32, 64, 128, 256, 512MB, or 1GB densities. DIMM Sockets DIMM Notch Socket Break Install a DIMM 1. Unlock a DIMM socket by pressing the retaining clips outward. Align a DIMM on the socket such that the notches on the DIMM match the breaks on the socket. 2. Firmly insert the DIMM into the socket until the retaining clips snap back in place and the DIMM is properly seated. Installed DIMM DIMMs are keyed with notches so that they fit in only one direction. DO NOT force a DIMM into a socket to avoid damaging the DIMM. CAUTION
AP1 10 Server User â s Manual 27 2.6 Install a Hard Disk Drive The AP1 10 server comes with drive bays for internal hard disk drives. Y ou can install up to two internal hard disk drives. HDD Metal Cage The HDD metal cage is located right under the CD-ROM drive bay . Y ou have to remove the cage from the chassis to conveniently install a hard disk drive. Remove the HDD Cage 1. Remove the screws (indicated by circles) that secure the HDD cage to the front of the chassis. 2. Remove the screw on the side of the HDD cage. 3. Pull the HDD cage out of the chassis. Cage Screw Cage Screw HDD Metal Cage
28 Chapter 2: Hardware Setup 2.6 Install a Hard Disk Drive Install the HDD 1. Insert the HDD into the cage (label side up) until the holes on the sides align. 2. Secure the HDD with four screws (two on each side). Replace the HDD Cage 1. Carefully insert the HDD cage back into the chassis until it fits in place. 2. Secure the cage with the screws you removed earlier .
AP1 10 Server User â s Manual 29 Connect the Cables 1. Connect one end of the IDE cable to the IDE connector at the back of the drive, matching the red stripe on the cable with Pin 1 on the IDE connector . 2. Connect a power cable (plug marked P3 or P4) to the power connector at the back of the drive. 3. Connect the other end of the IDE cable to the primary IDE connector (blue connector) on the motherboard. IDE Cable Red Stripe to Pin 1 Power Cable (P3 or P4) 2.6 Install a Hard Disk Drive IDE HDD Cabling The picture on the left shows an installed HDD. Primary IDE Connector
30 Chapter 2: Hardware Setup 2.7 Replace the Covers Re-install the Panel 1. Align the bottom edge of the panel to the chassis. 2. Firmly push the panel with both hands until it fits in place. 3. Open the panel door . 4. Secure the panel with the two screws that you removed earlier . 5. Lock the front panel with the system key . Re-install the Cover 1. Place the cover from the top of the chassis, leaving about an inch from the rear edge. 2. Slide the cover toward the rear panel until it fits in place. NOTE If you are installing optional components such as the IDE RAID kit, proceed to Chapter 4 before replacing the covers.
31 AP1 10 Server User â s Manual This chapter tells how to get started with the AP1 10 server . Powering up the server basically includes connecting the cables and turning power on. Chapter 3 Powering Up
32 Chapter 3: Powering Up 3.1 Getting Star ted Make sure that you have completed the basic system installations in Chapter 2, then follow these steps to start up the server . Connect a Monitor Connect a monitor by plugging hte monitor cable to the video port (blue port) on the server rear panel. Connect the Power Cord 1. Adjust the voltage selector to the correct voltage in your area. 2. Connect a power cord to the power connector on the rear panel. 3. Plug the power cord to a grounded wall socket. Power On T urn on the server by pressing the power button on the front panel. Check Power Status After turning on the power , the power LED lights up. If it doesnâÂÂt, check the power connection. Video Port Power Button Power LED Power Connector V oltage Selector
33 AP1 10 Server User â s Manual This chapter tells how to install the optional IDE RAID kit. Chapter 4 Hardware Options
34 Chapter 4: Hardware Options 4.1 IDE RAID Kit The AP1 10 server supports a maximum of four hard disk drives, two external and two internal. The external HDD bays are available for an IDE RAID configuration using the optional IDE RAID Kit. This chapter tells about external HDD installation using the IDE RAID kit. Refer to Chapter 3 for instructions on internal HDD installation. IDE RAID Kit Contents NOTE The IDE RAID kit is optional and does not come with all models. If your server includes a RAID kit, it comes already pre-installed in the chassis. Hot-swap HDD T ray Sets RAID Card Security Keys Screws A T A/100 IDE Cables NOTE The IDE RAID kit also includes a diskette that contains the IDE drivers and a RAID card user â s manual.
AP1 10 Server User â s Manual 35 HDD T ray Frame The HDD tray frame is a separate unit that holds the hot-swap drive tray . A 64-pin male connector is found on the rear of the frame. This connector matches the 64-pin female connector at the back of the hot-swap drive tray . The back of the tray frame is an HDD fan, an IDE connector (male), and a power connector . HDD Fan Hot-swap HDD T ray The hot-swap drive tray is an enclosure that holds the HDD. The drive tray interior includes an IDE cable and a power cable. Power Connector IDE Connector 4.1 IDE RAID Kit 64-pin Male Connector Hot-swap HDD T ray with Cover IDE Cable Power Cable 64-pin Female Connector
36 Chapter 4: Hardware Options 4.2 Install a Hot-swap HDD Install HDD T ray Frame 1. Insert an HDD tray frame into one external drive bay as shown. 3. Follow steps 1 and 2 to install the second HDD tray frame. The picture on the right shows the two installed HDD tray frames. 2. Secure the frame with four screws (two on each side). NOTE: Align the front screws with the holes labeled 1. Frame Screw Align with Hole 1
AP1 10 Server User â s Manual 37 4.2 Install Hot-swap HDD Remove HDD T ray Cover The hot-swap drive tray has a cover that you have to remove before you can install a hard disk. T o remove the tray cover: 1. Pull up the lever on the front of the tray . Doing this action slides the tray cover backward about a quarter of an inch. 2. Following the direction of the arrow in the picture, use a finger to flip out the metal latch on the front corner of the cover to disengage it from the tray . 3. Slide the cover all the way back to remove it. T ray Lever Metal Latch
38 Chapter 4: Hardware Options 4.2 Install Hot-swap HDD Install an IDE Drive 1. Connect the IDE cable to the IDE connector at the back of the drive. 2. Connect the power cable to the power connector at the back of the drive. 3. Carefully place the drive into the tray until it fits in place. 4. Secure the drive with four screws (two on each side). 5. Align the tray cover to the rails at the back of the tray , then slide the cover forward until the metal latch clicks in place. 6. Insert the hot-swap drive tray into the bay until it is flushed to the front panel. 7. Lock the hot-swap drive tray with the security key to prevent unauthorized access. 8. Do steps 1 to 7 to install the other hot-swap drive. Installed Hot-Swap Drive T rays IDE Cable Power Cable
AP1 10 Server User â s Manual 39 4.3 RAID Configuration Install a RAID Card 1. Remove the cover opposite the PCI1 expansion slot. 2. Carefully insert the golden fingers of the RAID card into the slot until the card is properly seated. RAID Card Connect IDE Cables 1. Connect one end of an IDE cable to the IDE1 connector on the RAID card, and the other end to the back of a hot-swap drive frame. 2. Connect one end of the second IDE cable to the IDE2 connector on the RAID card, and the other end to the second hot-swap drive frame. This section presents only the physical hardware connections of the RAID card, hot-swap HDDs, and IDE and power cables. For detailed instructions on RAID configuration, refer to the user âÂÂs manual that came with the IDE RAID kit. IDE2 Connector IDE1 Connector IMPORT ANT Use two separate IDE cables for IDE1 and IDE2 connections.
40 Chapter 4: Hardware Options 4.3 RAID Configuration Connect Power Cables Connect the power cables, with plugs labeled P5 and P6, to the power connectors at the back of the hot-swap drive frames. 4.4 Removing a Hot-swap HDD Tray In the future, you might need to remove the drive tray and replace a hot-swap HDD. T o remove a hot-swap drive tray: 1. Unlock the drive tray you desire to remove. 2. Lift up the tray handle. 3. Pull the tray out of the bay . 4. Refer to section 4.2 for instructions on installing a hot- swap HDD. Power Cables
AP1 10 Server User â s Manual 41 4.5 CD-ROM Drive The server comes with the CD-ROM drive already installed. This section tells how to remove and re-install the CD-ROM drive. Y ou will need to remove the CD-ROM drive for either one of the following reasons: 1. Y ou need to replace the drive 2. Y ou need to remove the motherboard. The CD-ROM drive overlaps with the top right corner of the motherboard, so you can not get it out without moving the drive outward. Remove the CD-ROM Drive 1. Disconnect the power and IDE cables from the drive. 2. Remove the four screws (two on each side) that secure the drive to the chassis. 3. Carefully pull the drive out of the chassis. Power and IDE Cables CD-ROM Screws If you are doing the above procedure for the purpose of removing the motherboard, you do not have to completely remove the drive from the chassis. Simply pull out the drive for about an inch, or until you can access the motherboard. In this instance, you also have to pull out the hot-swap drive trays because they , too, overlap with the motherboard. NOTE T op Right Corner of the Motherboard Hot-swap HHD T rays and CD-ROM Drive Pulled Out
42 Chapter 4: Hardware Options 4.5 CD-ROM Drive Re-install the CD-ROM Drive 1. Align the CD-ROM drive to its bay and carefully push it inward until it is flushed to the front panel. 2. Secure the drive with the screws that you removed earlier (two on each side). NOTE: Align the front screw with the hole labeled 1. 3. Connect the IDE cable to the IDE connector at the back of the drive, matching the red pin stripe on the cable with Pin1 on the IDE connector . 4. Connect the power cable labeled P2 to the power connector at the back of the drive. Align with Hole 1 CD-ROM Screws IDE Cable Power Cable (P2) Red Stripe to Pin 1
43 AP1 10 Server User â s Manual This appendix gives information on the 250-watt switching power supply that comes with the AP1 10 server . Appendix A Power Supply
44 Appendix A: Power Supply A .1 General Description The server comes with a 250W A TX power supply with universal AC input that includes PFC and A TX-compliant output cables and connectors. The power supply has an internal cooling fan. The power supply has seven plugs labeled P1 to P7. The picture below shows the specific device assignments for the plugs. P2 P4 P3 P1 P5 P6 P7 P1. Motherboard A TX Power P2. CD-ROM Drive P3. Internal HDD P4. Internal HDD P5. Hot-swap HDD P6. Hot-swap HDD P7. Floppy Disk Drive
AP1 10 Server User â s Manual 45 Input Characteristics A .2 Specifications Output Characteristics Over-V oltage Protection (OVP) Input V oltage Range Min Nom Max Range 1 90V 1 15V 135V Range 2 180V 230V 265V Input Frequency Range 47 Hz to 63 Hz Maximum Input ac Current 9A max at 1 15V ac 5A max. at 230V ac, maximum load Inrush Current 70A max. at 1 15V ac, full load cold start at 25ðC Efficiency 68% min. at nominal input, maximum load Output Load Range Regulation Ripple V oltage Min Max Min Max Max 5V 1.5A 25.0A -5% 5% 50mV p-p 12V 0.2A 8.0A -5% 5% 120mV p-p -12V 0A 0.8A -10% 10% 150mV p-p -5V 0A 0.5A -5% 5% 100mV p-p 5Vsb 0A 2.0A -5% 5% 100mV p-p 3V3 0A 14.0A -5% 5% 50mV p-p Output V oltage Maximum V oltage 5V 6.5V 12V 15.6V 3.3V 4.3V NOTE The power supply will shut down and latch off for shorting 5V , 12V , -12V , -5V , or 3.3V . By shorting 5Vsb, the power supply can latch down or automatically recover when the fault condition is removed.
46 Appendix A: Power Supply
47 AP1 10 Server User â s Manual This appendix lists the common problems that you may encounter while using the AP1 10 server . It lists the possible causes of the problems and offers solutions. Y ou may refer to this part and try to solve simple problems before calling customer support. Appendix B T roubleshooting
48 Appendix B: T roubleshooting B.1 Simple Fixes The power LED on the server and/or the monitor do not light up NOTE Some problems that you may encounter are not due to defects on the system or the components. These problems only requires simple troubleshooting actions that you can perform by yourself. 1. Make sure that the 1 15V/230V voltage selector switch is set to the correct voltage supply in your area. 2. Check the power cable connection on the system rear panel if properly connected. 3. Make sure that the power cables are connected to a grounded power outlet. 4. Press the power button to make sure that the system is turned on. Problem Action The keyboard does not work Check the keyboard cable if properly connected to the keyboard port. The mouse does not work Check the mouse cable if properly connected to the mouse port. The system does not perform power-on self tests (POST) after it was turned on 1. Check the memory modules and make sure you installed the DIMMs the system supports. 2. Make sure that the DIMMs are properly installed on the sockets.
AP1 10 Server User â s Manual 49 The system continuously beeps after it was turned on 1. Check the memory modules and make sure you installed the DIMMs the system supports. 2. Make sure that the DIMMs are properly installed on the sockets. The message âÂÂNon-system disk or disk error â appears Check if bootable HDD is active. RAID HDD is only detected as 1024MB 1. Boot from DOS/Win9x floppy disk. 2. Run FDISK utility to delete all partition 3. Reboot the system and run FDISK /MBR. RAID HDD shows incorrect size when you execute FDISK If the RAID set is larger than 64GB, try using SPFDISK utility to solve the problem. PCI-IDE RAID controller does not detect HDDs Press F6 and load the PCI-IDE RAID driver when booting from Windows NT/200 OS CD. Onboard IDE HDD is unstable Install the VIA utility drivers from the ASUS support CD. Network connection not available 1. Make sure the network cable is connector the RJ-45 port on the rear panel. 2. Make sure that you have installed the network drivers from the motherboard support CD. Problem Action
50 Appendix B: T roubleshooting