Asus TR-DLSR User Manual

® TR-DLSR Dual Socket 370 Motherboard USER ’ S MANUAL
ASUS TR-DLSR User’ s Manual 2 USER'S NOTICE Product Name: ASUS TR-DLSR Manual Revision: 1.01 E709 Release Date: September 2001 No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUST eK COMPUTER INC. (“ASUS”). ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT W ARRANTY OF ANY KIND, EI- THER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED T O THE IMPLIED W AR- RANTIES OR CONDITIONS OF MERCHANT ABILITY OR FITNESS FOR A P AR TICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT , SPECIAL, INCIDENT AL, OR CONSEQUEN- TIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DA T A, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT . Product warranty or service will not be extended if: (1) the product is repaired, modified or al- tered, unless such repair , modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe. • Intel, LANDesk, and Pentium are registered trademarks of Intel Corporation. • W indows and MS-DOS are registered trademarks of Microsoft Corporation. • T rend and ChipA wayV irus are trademarks of T rend Micro, Inc. • Adobe and Acrobat are registered trademarks of Adobe Systems Incorporated. The product name and revision number are both printed on the product itself. Manual revisions are released for each product design represented by the digit before and after the period of the manual revision number . Manual updates are represented by the third digit in the manual revision number . For previous or updated manuals, BIOS, drivers, or product release information, contact ASUS at http://www .asus.com.tw or through any of the means indicated on the following page. SPECIFICA TIONS AND INFORMA TION CONT AINED IN THIS MANUAL ARE FURNISHED FOR INFORMA TIONAL USE ONL Y , AND ARE SUBJECT TO CHANGE A T ANY TIME WITH- OUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURA- CIES THA T MA Y APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFT - W ARE DESCRIBED IN IT . Copyright © 2001 ASUST eK COMPUTER INC. All Rights Reserved.
ASUS TR-DLSR User’ s Manual 3 ASUS CONT ACT INFORMA TION ASUST eK COMPUTER INC. (Asia-Pacific) Address: 150 Li-T e Road, Peitou, T aipei, T aiwan 1 12 General T el: 886-2-2894-3447 General Fax: 886-2-2894-3449 General Email: info@asus.com.tw T echnical Support MB/Others (T el): 886-2-2890-7121 (English) Notebook (T el): 886-2-2890-7122 (English) Desktop/Server (T el): 886-2-2890-7123 (English) Support Fax: 886-2-2890-7698 Support Email: tsd@asus.com.tw W eb Site: www .asus.com.tw Newsgroup: cscnews.asus.com.tw ASUS COMPUTER INTERNA TIONAL (America) Address: 6737 Mowry A venue, Mowry Business Center , Building 2, Newark, CA 94560, USA General Fax: 1-510-608-4555 General Email: tmd1@asus.com T echnical Support Support Fax: 1-510-608-4555 Notebook (T el): 1-877-918-ASUS (2787) W eb Site: www .asus.com Support Email: tsd@asus.com ASUS COMPUTER GmbH (Europe) Address: Harkortstr . 25, 40880 Ratingen, BRD, Germany General Fax: 49-2102-442066 General Email: sales@asuscom.de (for marketing requests only) T echnical Support Support Hotline: MB/Others: 49-2102-9599-0 Notebook (T el): 49-2102-9599-10 Support Fax: 49-2102-9599-1 1 Support (Email): www .asuscom.de/de/support (for online support) W eb Site: www .asuscom.de
ASUS TR-DLSR User’ s Manual 4 CONTENTS 1. INTRODUCTION ............................................................................. 7 1.1 How This Manual Is Or ganized ................................................... 7 1.2 Item Checklist .............................................................................. 7 2. FEA TURES ........................................................................................ 8 2.1 ASUS TR-DLSR Motherboard .................................................... 8 2.1.1 Specifications ..................................................................... 8 2.1.2 Performance ...................................................................... 10 2.1.3 Intelligence ....................................................................... 1 1 2.2 TR-DLSR Motherboard Components ........................................ 12 2.2.1 Component Locations ...................................................... 13 3. HARDW ARE SETUP ..................................................................... 14 3.1 TR-DLSR Motherboard Layout ................................................. 14 3.2 Layout Contents ......................................................................... 15 3.3 Hardware Setup Procedure ......................................................... 16 3.4 Motherboard Settings ................................................................. 16 3.5 System Memory ......................................................................... 19 3.5.1 Memory Configurations ................................................... 19 3.5.2 Memory Installation ......................................................... 20 3.6 Central Processing Unit (CPU) .................................................. 21 3.6.1 Installing the CPU and T erminator ................................... 22 3.6.2 Heatsink Installation ......................................................... 23 3.7 Expansion Cards ........................................................................ 24 3.7.1 Expansion Card Installation Procedure ............................ 24 3.7.2 Assigning IRQs for Expansion Cards .............................. 25 3.8 Connectors ................................................................................. 27 3.8.1 External Connectors ......................................................... 27 3.8.2 Internal Connectors .......................................................... 29 3.9 Starting Up the First T ime .......................................................... 38 A ward BIOS Beep Codes ...................................................... 38
ASUS TR-DLSR User’ s Manual 5 CONTENTS 4. BIOS SETUP ..................................................................................... 39 4.1 Managing and Updating Y our BIOS .......................................... 39 4.1.1 Upon First Use of the Computer System .......................... 39 4.1.2 Updating BIOS Procedures .............................................. 41 4.2 BIOS Setup Program .................................................................. 43 4.2.1 BIOS Menu Bar ................................................................ 44 4.2.2 Legend Bar ....................................................................... 44 4.3 Main Menu ................................................................................. 46 4.3.1 Primary & Secondary Master/Slave ................................. 47 4.3.2 Keyboard Features ............................................................ 50 4.4 Advanced Menu ......................................................................... 52 4.4.1 Chip Configuration ........................................................... 54 4.4.2 I/O Device Configuration ................................................. 55 4.4.3 PCI Configuration ............................................................ 56 4.4.4 Shadow Configuration ...................................................... 58 4.5 Power Menu ............................................................................... 59 4.5.1 Power Up Control ............................................................. 61 4.5.2 Hardware Monitor ............................................................ 63 4.6 Boot Menu ................................................................................. 64 4.7 Exit Menu ................................................................................... 66 5. OS Driver Installation ...................................................................... 69 (T urn to page 69 for detailed contents on OS Drivers)
ASUS TR-DLSR User’ s Manual 6 FCC & DOC COMPLIANCE Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer's instructions, may cause harmful interference to radio communications. However , there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Re-orient or relocate the receiving antenna. • Increase the separation between the equipment and receiver . • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. W ARNING! Any changes or modifications to this product not expressly approved by the manufacturer could void any assurances of safety or performance and could result in violation of Part 15 of the FCC Rules. Reprinted from the Code of Federal Regulations #47, part 15.193, 1993. W ashington DC: Office of the Federal Register , National Archives and Records Administration, U.S. Government Printing Of fice. Canadian Department of Communications Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
ASUS TR-DLSR User ’ s Manual 7 1.1 How This Manual Is Organized This manual is divided into the following sections: 1. INTRODUCTION Manual information and checklist 2. FEA TURES Product information and specifications 3. HARDW ARE SETUP Instructions on setting up the motherboard. 4. BIOS SETUP Instructions on setting up the BIOS 5. SOFTW ARE SETUP Instructions on setting up the included software 6. SOFTW ARE REFERENCE Reference material for the bundled software 7. APPENDIX Optional items and general reference 1.2 Item Checklist Check that your package is complete. If you discover damaged or missing items, contact your retailer . (1) ASUS Motherboard (1) I/O Shield (1) Ribbon cable for master and slave IDE drives (1) 68-pin L VD SCSI ribbon cable for Ultra160 devices with T erminator (1) Ribbon cable for a 3.5 ” floppy disk drive (1) Support drivers and utilities (1) User ’ s Manual Optional Items (1) PGA370 CPU T erminator (required when installing only one CPU) 1. INTRODUCTION 1. INTRODUCTION Manual / Checklist
8 ASUS TR-DLSR User ’ s Manual 2. FEA TURES Specifications 2. FEA TURES 2.1 ASUS TR-DLSR Motherboard The ASUS TR-DLSR motherboard is designed primarily for multi-server environments to optimize available space without sacrificing performance. Powered by dual Intel ® Pentium ® III T ualatin ™ processors, the TR-DLSR ef ficiently complies with today ’ s demand for a high-integration server . 2.1.1 Specifications • Latest Intel Pr ocessor Support: Supports dual Socket 370-based Intel Pentium III T ualatin processors running up to 1.4GHz with 133MHz Front Side Bus (FSB) frequency • Multi-Processor OS: Supports multi-processor operating systems such as W indows NT/2000, Unix, Linux, and Netware when dual processors of the same type and speed are installed. • ServerW orks LE 3.0 Chipset: Features the ServerW orks LE 3.0 North Bridge and RCC Open South Bridge. Supports PC133 SDRAM with ECC, dual peer to peer PCI buses, and 64-bit 66MHz PCI bus speed. • Onboard Graphics: Features A TI RAGE-XL PCI VGA controller that supports up to 4MB PC100-compliant 10ns SDRAM for 1280x1024 and true color resolutions. • Smart Networking: Features two Intel 82559 Fast-Ethernet LAN controllers that fully support Alert-On-LAN II (AOL-II) and 10BASE-T/100BASE-TX. • PC133 Memory Support: Equipped with four Dual Inline Memory Module (DIMM) sockets that support up to 4GB of registered ECC SDRAMs (available in 64, 128, 256, 512MB, or 1GB densities). • SCSI Support: Equipped with the LSI 53C1010 Ultra160 64-bit dual-channel SCSI controller supports up to 30 SCSI devices. • Standard IDE Support: Comes with an onboard PCI Bus Master IDE controller with two connectors that support four IDE devices on two channels. Supports PIO Modes 3 and 4 IDE devices, such as DVD-ROM, CD-ROM, CD-R/R W , LS-120, and T ape Backup drives. • PCI Expansion Slot: One 64-bit 66MHz PCI slot • USB Ports: T wo stacked USB connectors to provide for additional peripherals • SMBus: Features the System Management Bus interface, which is used to physically transport commands and information between SMBus devices.
ASUS TR-DLSR User ’ s Manual 9 2. FEA TURES 2. FEA TURES Specifications • W ake-Up Support: Supports W ake-On-LAN and W ake-On-Ring, and BIOS W ake-Up. • ISA Multi-I/O: Provides two high-speed UAR T compatible serial ports and one parallel port with EPP and ECP capabilities. • Server Health Monitoring: Provides an easy way to examine and manage system status information, such as CPU and systerm voltages, temperatures, and fan status through the onboard hardware ASUS ASIC. • Enhanced ACPI: Programmable BIOS (Flash EEPROM), offering enhanced ACPI for W indows 2000 compatibility , and autodetection of most devices for virtually automatic setup. • CPU Throttling: This feature protects the CPU from overheating.
10 ASUS TR-DLSR User ’ s Manual Performance 2. FEA TURES 2. FEA TURES 2.1.2 Performance • UltraPerformance: Onboard Ultra160 dual channel SCSI controller with two connectors that support 30 Ultra160 SCSI devices in two channels. • High-Speed Data T ransfer Interface: SCSI transfers using Ultra160 dual- channel SCSI controller can handle rates up to 160MB/s. Ultra160 is backward compatible with slower SCSI devices so that older SCSI devices are not wasted. (Ultra160 SCSI cables have twisted pairs compared to flat ribbon cables used in older SCSI standards.) • SDRAM Optimized Performance: This motherboard supports PC133 “ registered” Synchronous Dynamic Random Access Memory (SDRAM), which increases the data transfer rate to 1064MB/s max • ACPI Ready: ACPI (Advanced Configuration and Power Interface) is also implemented on all ASUS smart series motherboards. ACPI provides more Energy Saving Features for future operating systems (OS) supporting OS Direct Power Management (OSPM) functionality . W ith these features implemented in the OS, PCs can be ready around the clock, yet satisfy all the ener gy saving standards. T o fully utilize the benefits of ACPI, use an ACPI-supported OS, such as W indows 2000. • Compliance: Both the Microsoft WHQL and hardware levels of the motherboard meet the requirements for SDG2.0 certification. The new SDG2.0 requirements for systems and components are based on the following high-level goals: support for Plug and Play compatibility and power management for configuring and managing all system components, and 32-bit device drivers and installation procedures for W indows NT/2000. Color-coded connectors and descriptive icons make identification easy as required by PC ‘99.
ASUS TR-DLSR User ’ s Manual 11 2. FEA TURES Intelligence 2.1.3 Intelligence • Fan Status Monitoring and Alarm: T o prevent system overheat and system damage, the CPU, power supply , and system fans can be monitored for RPM and failure. All the fans are set for its normal RPM range and alarm thresholds. • T emperature Monitoring and Alert: T o prevent system overheat and system damage, this motherboard supports processor thermal sensing and auto-protection. • V oltage Monitoring and Alert: System voltage levels are monitored to ensure stable current to critical motherboard components. V oltage specifications are more critical for future processors, so monitoring is necessary to ensure proper system configuration and management. • Remote Ring On (requir es modem): This allows a computer to be turned on remotely through an internal or external modem. W ith this benefit on-hand, users can access any information from their computers from anywhere in the world. • Alert-on-LAN II (requires optional hardwar e component): Part of W ired for Management to enable IT staff to remotely respond to and resolve system trouble that decreases down time and lower total cost of ownership. Remote management response via remote diagnostics and troubleshooting work even when the operating system has frozen. Remote power down for power management. Asset tracking and monitoring through features like presence ping and logoff notification. 2. FEA TURES
12 ASUS TR-DLSR User ’ s Manual 2. FEA TURES 2. FEA TURES M/B Components 2.2 TR-DLSR Motherboard Components See opposite page for locations. Location Processor Support Dual Socket 370 for Pentium III T ualatin Processors .............. 2 Chipsets ServerW orks ServerSet LE 3.0 North Bridge ........................... 3 ServerW orks Open South Bridge ........................................... 13 4Mbit Flash ROM .................................................................. 18 Super I/O Chipset ................................................................... 14 Integrated Graphics Controller ............................................... 17 Memory DIMM Sockets ......................................................................... 5 (Maximum 4GB support for PC133 registered SDRAM) Onboard VGA Memory .......................................................... 16 Expansion Slots 64-bit 66MHz PCI Slot ........................................................... 20 ASUS ASMS Connectors (ASMCSA/ASMCSB) ........... 1 1, 15 System I/O Floppy Disk Drive Connector ................................................ 10 Primary IDE Connector (IDE1) ............................................... 6 Secondary IDE Connector (IDE2) ........................................... 7 RJ-45 Fast-Ethernet Ports ...................................................... 22 Parallel Port .................................................................. (T op) 23 Serial Port ......................................................... (Bottom left) 23 VGA Monitor Connector ................................ (Bottom right) 23 USB Ports .............................................................................. 24 PS/2 Mouse Connector ................................................. (T op) 25 PS/2 Keyboard Connector ....................................... (Bottom) 25 Network Features Intel 82559 Fast-Ethernet Controller ...................................... 21 W ake-On-LAN Connector (see layout on page 14) W ake-On-Ring Connector (see layout on page 14) Hardware Monitoring System V oltage Monitoring (integrated in ASUS ASIC) ......... 1 Fan Power and Speed Monitoring Connectors (see layout on page 1 4 ) Power A TX Power Supply Connector ................................................. 4 CMOS Battery Lithium CR2032 3V ............................................................... 19 Special Feature LSI 64-bit 66MHz Ultra160 dual-channel SCSI controller ....................................................................... 12 Onboard SCSI Connector (SCSI-A) ......................................... 8 Onboard SCSI Connector (SCSI-B) ......................................... 9 Form Factor Full-size A TX
ASUS TR-DLSR User ’ s Manual 13 2. FEA TURES 2. FEA TURES M/B Components 2.2.1 Component Locations 2 22 23 6 18 21 16 9 17 5 20 24 1 8 7 10 11 12 13 14 15 19 3 4 25
14 ASUS TR-DLSR User ’ s Manual Motherboard Layout 3. H/W SETUP 3. HARDW ARE SETUP 3.1 TR-DLSR Motherboard Layout 7 6 DIMM Socket 3 (72-bit, 168-pin module) IDE1 ASUS ASIC with Hardware Monitor WOL_CON TR-DLSR COM1 P ARALLEL PORT VGA PS/2 T : Mouse B: Keyboard PCI 64-bit, 33MHz 2MB SDRAM 2MB SDRAM CHA_F AN2 CPU_F AN1 CPU_F AN1 P ANEL WOR SCSI-A 68-Pin Ultra160/Ultra3-Wide SCSI Connector SMB_PWR ServerWorks RCC-NB6635 North Bridge ServerWorks RCC-IB6566 South Bridge Super I/O AT I RAGE XL VGA Controller CR2032 3V Lithium Cell CMOS Power 35 68 34 1 A TX_POWER 5 4 DIMM Socket 2 (72-bit, 168-pin module) 3 2 DIMM Socket 1 (72-bit, 168-pin module) 1 0 DIMM Socket 0 (72-bit, 168-pin module) Intel Fast Ethernet Intel Fast Ethernet USB1 USB2 RJ-45 RJ-45 FLOPPY 4Mbit Flash BIOS CONFIG Switches (reserved) 1234 5678 PCI_EXTPWR P ANEL2 PWRBTN IDELED CPU_F AN2 COM2 ASMCSA ASMCSB IDE2 CHASSIS JP2 JP3 R323 LSI SCSI Controller 53C1010-66 68-Pin Ultra160/Ultra3-Wide SCSI Connector SCSI-B POLED JP1 Socket 370 Socket 370
ASUS TR-DLSR User ’ s Manual 15 3. HARDW ARE SETUP Layout Contents 3. H/W SETUP 3.2 Layout Contents Motherboard Settings 1) CONFIG 5-8 p. 17 CPU Bus Frequency Setting 2) CLR TC p. 18 Clear CMOS Expansion Slots 1) DIMM 0/1/2/3 p. 19 168-Pin System Memory Support 2) CPU p. 21 Central Processing Unit (CPU) 3) PCI p. 24 64-bit PCI Bus Expansion Slot External Connectors 1) PS2KBMS p. 27 PS/2 Mouse Connector (6-pin female) 2) PS2KBMS p. 27 PS/2 Keyboard Connector (6-pin female) 3) USB p. 27 Universal Serial Bus Ports 0 & 1 (two 4-pin female) 4) PRINTER p. 28 Parallel Port Connector (25-pin female) 5) COM1 p. 28 Serial Port COM1 Connector (9-pin male) 6) VGA p. 28 Monitor (VGA) Output Connector (15-pin female) 7) RJ-45 p. 28 Fast-Ethernet Connector (RJ45) Internal Connectors 1) IDE1/IDE2 p. 29 Primary/Secondary IDE Connectors (two 40-1 pin) 2) IDE LED p. 30 IDE/SCSI Activity LED 3) FLOPPY p. 30 Floppy Disk Drive Connector (34-1 pin) 4) WOL_CON p. 31 W ake-On-LAN Connector (3-pin) 5) WOR p. 31 W ake-On-Ring Connector (2-pin) 6) SCSI-A/SCSI-B p. 32 68-pin Ultra160 SCSI Connectors (two 68-pin) 7) CPU_F AN1/2 p. 33 CPU and Chassis Fan Connectors (four 3-pin) CHA_F AN1/2 8) CHASSIS p. 33 Chassis Open Alarm Lead (4-pin) 9) SMB p. 34 SMBus Connector (8-1 pins) 10 COM2 p. 36 Serial Port 2 (9-pin male) 1 1) ASMCSA/ p. 35 ASUS Ser Management Card Connectors ASMCSB 12) P ANEL2 p. 35 Panel 2 Connector (8-pin) 13) JP2/JP3 p. 35 Thermal Sensor Connectors (two 2-pin) 14) A TXPWR p. 36 A TX Power Supply Connector (20/24-pin) 15) PWRBTN p. 36 Power Button Connector (2-pin)
16 ASUS TR-DLSR User ’ s Manual 3. HARDW ARE SETUP Motherboard Settings 3. H/W SETUP 3.3 Hardware Setup Procedure Complete the following steps before using your computer: 1. Check motherboard settings 2. Install memory modules 3. Install the Central Pr ocessing Unit (CPU) 4. Install Expansion Cards 5. Connect ribbon cables, panel wires, and power supply cables 6. Configur e the BIOS parameter settings 3.4 Motherboard Settings This section tells you how to change motherboard function settings through the switches and/or jumpers. W ARNING! Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips. T o avoid damaging them due to static electricity , follow these precautions whenever you work on your computer . 1. Unplug the computer when working on the internal components. 2. Use a grounded wrist strap or touch a safely grounded object or to a metal object, such as the power supply case, before handling computer components. 3. Hold components by the edges and try not to touch the IC chips on them. 4. Whenever you uninstall any component, p lace the components on a grounded antistatic pad or i n the bag that came with the components. 5. Before you install or r emove any component, ensure that the A TX power supply is switched off or the power cord is detached from the power supply . Failure to do so may cause severe damage to the motherboard, peripherals, and/or components. 16) NIC (P ANEL) p. 37 NIC Activity LED (2-pin) 17) ST A TUS (P ANEL) p. 37 Status Activity LED (2-pin) 18) SMI (P ANEL) p. 37 System Management Interrupt Lead (2-pin) 19) PWRSW (P ANEL) p. 37 A TX Power Switch/Soft Off Lead (2-pin) 20) RESET (P ANEL) p. 37 Reset Switch Lead (2-pin) 21) PWR.LED (P ANEL) p. 37 System Power LED Lead (3-1 pin) 22) NMI (P ANEL) p. 37 Non-Mask Interrupt Switch (2-pin) 23) SPEAKER (P ANEL) p. 37 System W arning Speaker Connector (4-pin) 24) IDELED (P ANEL) p. 37 IDE/SCSI Activity LED (2-pin)
ASUS TR-DLSR User ’ s Manual 17 3. HARDW ARE SETUP 3. H/W SETUP Motherboard Settings DIP Switch Settings Y ou may change the CPU core bus frequency multiple using the DIP switches. The white block on a DIP switch represents the ON or OFF position. The figure below shows the location of the DIP switches on the motherboard and the function of each switch. CPU Cor e Bus Frequency Multiple (Switches 5-8) This option sets the frequency multiple between the CPU ’ s internal and external frequencies. The CPU frequencies must be set in conjuction with the CPU bus frequency . W ARNING! Frequencies other than the recommended CPU bus frequencies are not guaranteed to be stable. TR-DLSR TR-DLSR Configuration DIP Switches CONFIG 1. POWER ON 2. BOOTBLOCK 3. ON:CLEAR P ASSWORD 4. ON:CLEAR CONFIGUE 5. RESERVE1 6. RESERVE2 7. RESERVE3 8. RESERVE4 OFF ON 12345678 ON TR-DLSR TR-DLSR CPU : BUS Frequency Multiple 9.0x 8.5x 8.0x 7.0x 6.5x 7.5x 9.5x 12x 1 1.5x 10.5x 10x 11 x ON 12345678 ON 12345678 ON 12345678 ON 12345678 ON 12345678 ON 12345678 ON 12345678 ON 12345678 ON 12345678 ON 12345678 ON 12345678 ON 12345678
18 ASUS TR-DLSR User ’ s Manual 3. HARDW ARE SETUP 3. H/W SETUP Motherboard Settings Clear R TC RAM (R323) These two solder points allow you to clear the R TC RAM in CMOS. Y ou can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS Real T ime Clock (R TC) RAM. The RAM data that include system setup information, such as system passwords, is powered by the onboard button cell battery . T o erase the R TC RAM: 1. T urn OFF the computer and unplug the power cord. 2. Remove the battery . 3. Short the solder points for a few seconds. 4. Re-install the battery . 5. Plug the power cord and turn ON the computer . 6. Hold down the <Del> key during the boot process and enter BIOS setup to re-enter CMOS data. TR-DLSR TR-DLSR Clear RTC RAM Short solder points to Clear CMOS R323
ASUS TR-DLSR User ’ s Manual 19 3. HARDW ARE SETUP System Memory 3. H/W SETUP 3.5 System Memory This motherboard uses only Dual Inline Memory Modules (DIMMs). Four DIMM sockets are available for 3.3V olt (power level) registered Synchronous Dynamic Random Access Memory (SDRAM) of 16MB, 32MB, 64MB, 128MB, 256MB, 512MB, or 1GB densities with Serial Presence Detect (SPD) and Error Check and Correction (ECC). The motherboard supports a memory configuration of up to 4GB. One side (with memory chips) of the DIMM takes up one row on the motherboard. 3.5.1 Memory Configurations Install memory in any of the following combinations: DIMM Location 168-pin DIMM T otal Memory Socket 0 (Rows 0&1) SDRAM 64 MB, 12 8MB, 2 5 6MB, 512MB, 1G B x1 Socket 1 (Rows 2&3) SDRAM 64 MB, 12 8MB, 2 5 6MB, 512MB, 1G B x1 Socket 2 (Rows 4&5) SDRAM 6 4 MB, 12 8MB, 2 5 6MB, 512MB, 1 G B x 1 Socket 3 (Rows 6&7) SDRAM 6 4 MB, 12 8MB, 2 5 6MB, 512MB, 1 G B x 1 T otal System Memory (Max. 4GB) = IMPORT ANT : The system chipset only supports 64Mbit, 128Mbit, and 256Mbit “ registered” SDRAMs with ECC. Make sure to use the specified DIMM types for smooth system operation.
20 ASUS TR-DLSR User ’ s Manual 3. HARDW ARE SETUP Insert a DIMM into the DIMM socket as shown. Because the number of pins are different on either side of the breaks, the module only fits in one direction. SDRAM DIMMs have different pin contacts on each side. The notches on the DIMM shifts between left, center , or right to identify the type and also to prevent the wrong type from being inserted into the DIMM slot on the motherboard. Y ou must tell your retailer the correct DIMM type before purchasing. This motherboard supports four clock signals per DIMM. Use only 3.3V olt “ registered ” SDRAM DIMMs. T o determine the DIMM type, check the notches on the DIMMs (see the figure below). W ARNING! Make sure that you unplug the power supply when adding or removing memory modules or other system components. Failure to do so may cause severe damage to both the motherboard and expansion cards (see 3.3 Hardware Setup Procedure for more information). System Memory 3. H/W SETUP 3.5.2 Memory Installation TR-DLSR TR-DLSR 168-Pin DIMM Sockets 20 Pins 60 Pins 88 Pins
ASUS TR-DLSR User ’ s Manual 21 3. HARDW ARE SETUP 3.6 Central Processing Unit (CPU) The motherboard comes with a dual Socket 370 for Intel Pentium III T ualatin 1.4GHz CPUs with 133MHz Front Side Bus (FSB). The following illustration shows the location of the CPU sockets on the motherboard and the correct CPU orientation. Note in the illustration that the CPU and the terminator have marks (usually a notch or a gold mark on one corner) to help you identify the proper orientation and enable you to correctly install them. It is important that you match the marked corner of the CPU and terminator with the corresponding corner on the socket so as not to damage the CPU pins. Proceed to the next section for the steps on how to properly install the CPU and the specially designed heatsink for the 1U system. CPU 3. H/W SETUP W ARNING! If you are installing this motherboard into a 1U system,you must use a specially designed heatsink qualified for critical environments. Failure to do so will cause the CPU to overheat and may damage both the CPU and the motherboard. TR-DLSR TR-DLSR Socket 370 Gold Arrow Socket 370 T erminator (Use when only one CPU is installed) Silver Arrow Socket 370 Pentium III (T ualatin)
22 ASUS TR-DLSR User ’ s Manual 3. HARDW ARE SETUP CPU Installation 3. H/W SETUP 3.6.1 Installing the CPU and T erminator Follow these steps to install a CPU. 1. Locate the ZIF socket on the motherboard. 2. Unlock the socket by pressing the lever sideways then lifting it up to a 90 ° -100° angle. 3. Position the CPU above the socket such that its notched or marked corner matches the socket corner near the end of the lever , while making sure that the CPU is parallel to the socket. 4. Carefuly insert the CPU into the socket until it fits in place. CAUTION! The CPU fits only in one orientation. Do not force the CPU into the socket to prevent bending the pins and damaging the CPU. If the CPU does not fit completely , check its orientation or check for bent pins. 5. When the CPU is in place, press it firmly on the socket while you push down the socket lever to secure the CPU. The lever clicks on the socket indicating that it is locked. NOTE: Do not forget to set the correct Bus Frequency and Multiple (frequency multiple setting is available only on unlocked processors) for the processor to avoid start-up problems. 6. Install the CPU terminator the same way as you would install a CPU. The figure on the right shows an installed CPU terminator .
ASUS TR-DLSR User ’ s Manual 23 3. HARDW ARE SETUP 3.6.2 Heatsink Installation Follow these steps to install a CPU. 1. Carefully place the heatsink on top of the installed CPU and hook one end of the retaining clip to the protruding tab on the front of the socket. (TIP: The front part of the socket is where you find the gold mark or notch on the CPU.) 2. Use a flat screwdriver to hook the other end of the retaining clip to the protruding tab at the back of the CPU socket. 3. Check and make sure that the retaining clip is properly in place. Retaining Clip for the T ab on the Front of the Socket Retaining Clip for the T ab at the Back of the Socket
24 ASUS TR-DLSR User ’ s Manual 3. HARDW ARE SETUP 3.7 Expansion Cards 3.7.1 Expansion Card Installation Procedure 1. Read the documentation for your expansion card and make any necessary hardware or software settings for your expansion card, such as jumpers. 2. Remove your computer system cover and the bracket plate on the expansion slot. Keep the bracket for possible future use. 3. Lift the locking tab on top of the slot. If you are installing a long expansion card, lift the metal card guide also. This card guide is located on the bracket near the chassis fans. 4. Detach the riser card from the PCI card slot on the motherboard. 5. Carefully insert the golden fingers of the expansion card into the connector on the riser card. 6. Align the card bracket to the slot opening at the back of the system unit while inserting the end of the bracket to the slot holding tab. 7. Insert the golden fingers of the riser card to the PCI slot on the motherboard until it fits in place. 8. Press down the locking tab at the top of the expansion slot to secure the card. 9. If you installed a long expansion card, pull down the metal card guide and fit it to the other end of the card to hold the card in place. 10. Install the necessary software drivers for your expansion card. W ARNING! Unplug the power supply when adding or removing expansion cards or other system components. Failure to do so may cause severe damage to both your motherboard and expansion cards. Locking T ab Expansion Card Riser Card PCI Slot
ASUS TR-DLSR User ’ s Manual 25 3. HARDW ARE SETUP Expansion Cards 3. H/W SETUP 3.7.2 Assigning IRQs for Expansion Cards Some expansion cards need an IRQ to operate. Generally , an IRQ must be exclusively assigned to one use. In a standard design, there are 16 IRQs available but most of them are already in use, leaving 6 IRQs free for expansion cards. If the motherboard has PCI audio onboard, an additional IRQ will be used. If the motherboard also has MIDI enabled, another IRQ will be used, leaving 4 IRQs free. The following table lists the default IRQ assignments for standard PC devices. Use this table when configuring your system and for resolving IRQ conflicts. ISA Interrupt (IRQ) Assignments ISA INT Priority Standard Function ISA 00 1 System T imer ISA 01 2 Keyboard Controller ISA 02 N/A Programmable Interrupt ISA 03* 1 1 Communications Port (COM2) ISA 04* 12 Communications Port (COM1) ISA 05* 13 Sound Card (sometimes LPT2) ISA 06 14 Floppy Disk Controller ISA 07* 15 Printer Port (LPT1) ISA 08 3 System CMOS/Real T ime Clock ISA 09* 4 ACPI Mode when used ISA 10* 5 IRQ Holder for PCI Steering ISA 11* 6 IRQ Holder for PCI Steering ISA 12* 7 PS/2 Compatible Mouse Port ISA 13 8 Numeric Data Processor ISA 14* 9 Primary IDE Channel ISA 15* 10 Secondary IDE Channel *These IRQs are usually available for PCI devices.
26 ASUS TR-DLSR User ’ s Manual 3. HARDW ARE SETUP Expansion Cards 3. H/W SETUP PCI Interrupt (IRQ) Assignments Device PCI INT A PCI INTB PCI INTC PCI INTD 64-bit PCI Slot PCI 00 PCI 13 PCI 14 PCI 15 Device Assignment A TI V ideo PCI10 Intel 82559 #1 PCI6 Intel 82559 #2 PCI7 LSI 1010-66 CHA PCI8 LSI 1010-66 CHB PCI9 IRQ Assignments for Other Onboard Devices
27 3. HARDW ARE SETUP ASUS TR-DLSR User ’ s Manual 3. H/W SETUP Connectors 3.8 Connectors 3.8.1 External Connectors 1) PS/2 Mouse Port (Gr een 6-pin PS2KBMS) The system will direct IRQ12 to the PS/2 mouse if one is detected. If one is not detected, expansion cards can use IRQ12. 2) PS/2 Keyboard Connector (Purple 6-pin PS2KBMS) This connection is for a standard keyboard using an PS/2 plug (mini DIN). This connector does not allow standard A T size (large DIN) keyboard plugs. Y ou may use a DIN to mini DIN adapter on standard A T keyboards. PS/2 Mouse (6-pin female) PS/2 Keyboard (6-pin female) 3) Universal Serial BUS Ports 1 & 2 (Black two 4-pin USB) T wo USB ports are available for connecting USB devices. Universal Serial Bus (USB) 2 USB 1
28 3. HARDW ARE SETUP ASUS TR-DLSR User ’ s Manual 3. H/W SETUP Connectors 4) Parallel Port Connector (Burgundy 25-pin PRINTER) A 25-pin port is available for a parallel printer . Enable the parallel port and select the IRQ through Onboard Parallel Port parameter in BIOS. (See 4.4.2 I/O Device Configuration) . 7) Fast Ethernet LAN Connector (R-J45) The RJ-45 connector allows connection to a Local Area Network (LAN) through a network hub. 5) Serial Port Connector (T eal/T urquoise 9-pin COM1) One serial port is available for pointing devices or other serial devices. T o enable the port, see Onboard Serial Port 1 in 4.4.2 I/O Device Configuration . 6) VGA Connector (Blue 15-pin VGA) This connector is for a VGA monitor and other VGA-compatible devices. Parallel Port (25-pin female) Serial Port (9-pin male) COM 1 VGA Monitor (15-pin female) RJ-45 Port
29 3. HARDW ARE SETUP ASUS TR-DLSR User ’ s Manual 3. H/W SETUP Connectors 3.8.2 Internal Connectors W ARNING! Some pins are used for connectors or power sources. These are clearly distinguished from jumpers in the Motherboard Layout. Placing jumper caps over these connector pins will cause damage to your motherboard. IMPORT ANT : Always connect ribbon cables such that the red stripe matches Pin 1 on the connector . Pin 1 is usually on the side closest to the power connector on hard disk drives and CD-ROM drives, but may be on the opposite side on floppy disk drives. 1) Primary/Secondary IDE Connectors (40-1 pin IDE1/IDE2) These connectors support UltraDMA/33 IDE hard disks. Use IDE ribbon cables to connect the master and slave devices to these connectors. If you install two hard disks, you must configure the second drive as a slave device by setting its jumper accordingly . Refer to the hard disk documentation for the jumper settings. BIOS supports specific device bootup (see 4.6. Boot Menu ). NOTE: Pin 20 on each IDE connector is removed to match the covered hole on the UltraDMA cable connector . This prevents incorrect orientation when you connect the cables. TIP: Y ou may configure two hard disks to be both Masters with two ribbon cables – one for the primary IDE connector and another for the secondary IDE connector . TR-DLSR TR-DLSR IDE Connectors NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1. IDE2 IDE1 PIN 1 PIN 1
30 3. HARDW ARE SETUP ASUS TR-DLSR User ’ s Manual 3. H/W SETUP Connectors 2) IDE/SCSI Activity LED (2-pin IDELED) This connector supplies power to the chassis activity LED. Read and write activity by devices connected to the primary/secondary IDE and SCSI connectors cause the LED to light up. NOTE: Another 2-pin IDE LED connector is available in the connector labeled P ANEL. TR-DLSR TR-DLSR IDE Activity LED *Same as the “ HDD Access LED ” in the panel connectors IDELED - 3) Floppy Disk Drive Connector (34-1 pin FLOPPY) This connector supports the provided floppy drive ribbon cable. After connecting the single end to the board, connect the two plugs on the other end to the floppy drives. (Pin 5 is removed to pr event inserting in the wr ong orientation when using ribbon cables with pin 5 plugged). TR-DLSR NOTE: Orient the red markings on the floppy ribbon cable to PIN 1. TR-DLSR Floppy Disk Drive Connector PIN 1
31 3. HARDW ARE SETUP ASUS TR-DLSR User ’ s Manual 3. H/W SETUP Connectors 4) W ake-On-LAN Connector ( 3 -pin WOL_CON) This connector connects to a LAN card with a W ake-On-LAN output, such as the ASUS PCI-L101 Ethernet card (see 7. APPENDIX). The connector powers up the system when a wakeup packet or signal is received through the LAN card. IMPORT ANT : This feature requires that W ake On LAN is enabled (see 4.5.1 Power Up Control ) and that your system has an A TX power supply with at least 720mA 5V standby power . 5) W ake-On-Ring Connector ( 2 -pin W O R ) This connector connects to internal modem cards with a W ake-On-Ring output. The connector powers up the system when a ringup packet or signal is received through the internal modem card. NOTE: For external modems, W ake-On-Ring is detected through the COM port. IMPORT ANT : This feature requires that the Power Up on Modem Act parameter is enabled (see 4.5.1 Power Up Control ) and that the system has an A TX power supply with at least 720mA 5V standby power . TR-DLSR TR-DLSR W ake-On-LAN Connector IMPORT ANT : Requires an A TX power supply with at least 720mA 5 volt standby power 5 V olt Standby PME Ground WOL_CON TR-DLSR TR-DLSR W ake-On-Ring Connector WOR Ring# Ground 2 1
32 3. HARDW ARE SETUP ASUS TR-DLSR User ’ s Manual 3. H/W SETUP Connectors 6) T wo 68-pin Ultra160 SCSI Connectors (SCSI-A, SCSI-B) This motherboard has two 68-Pin Ultra160 SCSI connectors; one for each of the two channels. Each channel can support a maximum of 15 devices as specified by Ultra160 standards. SCSI Connection Notes This motherboard has two 68-Pin Ultra160 SCSI connectors; one for each of the two channels. The onboard SCSI chipset incorporates an advanced multimode I/O cell that supports both single-ended (SE), Ultra2, and Ultra160 devices. W ith Ultra160 devices, the SCSI bus platform performs at full Ultra160 speeds (up to 160MB/sec) and extended cabling 12m (or 25m in a point-to-point configuration). When an SE device is attached, the bus defaults to an SE speed and 1.5m cable length. IMPOR T ANT : Connect SCSI devices as shown. Each channel should have only one type of SCSI standard (e.g. Ultra160, Ultra2, Ultra-W ide). Mixing SCSI devices on the same channel decreases performance of the slower device. NOTE: Ultra160 SCSI devices do not have termination jumpers and must use a separate terminator on the last connector (internal) or device (external). TR-DLSR TR-DLSR Onboard SCSI Connectors 35 68 34 1 35 68 34 1 SCSI-A (Internal) 68-Pin Ultra160/Ultra2-Wide SCSI Connector SCSI-B (External) 68-Pin Ultra160/ Ultra2-Wide SCSI Connector TR-DLSR TR-DLSR SCSI Connection Example 68-pin Internal SCSI Cable (T wisted-Pair Ribbon) 68-pin Female T erminator Internal SCSI Devices (up to 15 devices) Channel A 68-pin Internal SCSI Cable (T wisted-Pair Ribbon) 68-pin Female T erminator Internal SCSI Devices (up to 15 devices) Channel B
33 3. HARDW ARE SETUP ASUS TR-DLSR User ’ s Manual 3. H/W SETUP Connectors 7) CPU and Chassis Fan Connectors (3-pin CPU_F AN1/2, CHA_F AN1/2) These connectors support cooling fans of 860mA (10.3 W atts) or less. Orient the fans so that the heat sink fins allow airflow to go across the onboard heat sink(s) instead of the expansion slots. Depending on the fan manufacturer , the wiring and plug may be dif ferent. The red wire should be positive, while the black should be ground. Connect the fan ’ s plug to the board taking into consideration the polarity of the connector . NOTE: The “ Rotation ” signal is to be used only by a specially designed fan with rotation signal. The Rotations Per Minute (RPM) can be monitored using Intel LDS M Utility (provided with certain models). W ARNING! The CPU and/or motherboard will overheat if there is no airflow across the CPU and onboard heatsinks. Damage may occur to the motherboard and/or the CPU fan if these pins are incorrectly used. These are not jumpers, do not place jumper caps over these pins. 8) Chassis Open Alarm Lead Connector (CHASSIS) This connector is designed for chassis intrusion detection. When any chassis component is removed, the contact should open and the motherboard will record a chassis intrusion event. The event can be processed by software such as LDSM. TR-DLSR 12-V olt Cooling Fan Power CHA_F AN1 / CHA_F AN2 CPU_F AN1 / CPU_F AN2 GND Rotation 12V GND Rotation 12V TR-DLSR GND Rotation 12V GND Rotation 12V TR-DLSR TR-DLSR Chassis Open Alarm Lead Ground Chassis Signal 3 CHASSIS *Same as the “Chassis intrude ” lead in the panel connectors 4 (no connection) 1
34 3. HARDW ARE SETUP ASUS TR-DLSR User ’ s Manual 3. H/W SETUP Connectors 9) SMBus Connector (8-1 pin SMB) This connector allows you to connect SMBus (System Management Bus) devices. SMBus devices communicate by means of the SMBus with an SMBus host and/ or other SMBus devices. SMBus is a specific implementation of an I 2 C bus, which is a multi-device bus; that is, multiple chips can be connected to the same bus and each one can act as a master by initiating data transfer . TR-DLSR TR-DLSR SMBus Power Connector AC_OK GND 5V INI2CDA T A3 IDELED- INI2CCLK3 1 GND 10) Serial Port 2 Connector (COM2) This motherboard has a second serial port connector to accommodate additional serial peripherals. See the BIOS section 4.4.2 I/O Device Configuration to configure Serial Port 2 settings. TR-DLSR TR-DLSR Serial COM2 Bracket PIN 1
35 3. HARDW ARE SETUP ASUS TR-DLSR User ’ s Manual 3. H/W SETUP Connectors 1 1) ASMC Connectors (ASMCSA/ASMCSB) (Reserved) This motherboard has two ASMC connectors that can support the ASUS Server Management Card (ASMC). The ASMC is a future option. TR-DLSR TR-DLSR ASMC Connector 12) Panel 2 Connector (P ANEL2) This connector supports some of the functions in the 20-pin P ANEL connector , such as the power button, IDE LED, and power LED. TR-DLSR TR-DLSR Panel 2 Connector * Requires an A TX power supply . 5V GND IDELED IDELED- PLED PWRBTN# A TX Power Button* IDELED Power LED 1 13) Thermal Sensor Connectors (JP2/JP3) These connectors are for the thermal sensor cables from the power supply . TR-DLSR TR-DLSR Thermal Sensor Connectors JP2 Thermal Sensor for CPU JP3
36 3. HARDW ARE SETUP ASUS TR-DLSR User ’ s Manual 3. H/W SETUP Connectors 15) Power Button Connector (PWRBTN) This connector allows you to turn the system ON or OFF . The power LED lights up when the system is turned ON. 14) A TX Power Connector (20/24-pin block A TXPWR) This connector connects to an A TX power supply . The plug from the power supply fits in only one orientation because of the different hole sizes. Find the proper orientation and push down firmly making sure that the pins are aligned. IMPORT ANT : Make sure that your A TX power supply can supply at least 720mA on the 5-volt standby lead ( 5VSB). Y ou may experience difficulty in turning ON your system if your power supply cannot support the load. TR-DLSR TR-DLSR A TX Power Connector 3 V olts 3 V olts Ground 5 V olts 5 V olts Ground Ground Power OK 5V Standby 12 V olts -5 V olts 5 V olts 3 V olts -12 V olts Ground Ground Ground PSON# Ground 5 V olts 12 V olts 3 V olts 5 V olts 1 Ground TR-DLSR TR-DLSR Power Button Connector GND PWRBTN# 1 PWRBTN
37 3. HARDW ARE SETUP ASUS TR-DLSR User ’ s Manual 3. H/W SETUP Connectors 16) NIC Activity LED Lead (2-pin) This shows the status of the NIC through a panel-mounted LED. 17) Status LED (2-pin) This shows the system status as programmed through the ASUS ASIC. 18) System Management Interrupt Lead (2-pin) This allows the user to manually place the system into a suspend mode or “ Green ” mode where system activity will be instantly decreased to save electricity and expand the life of certain components when the system is not in use. This 2-pin connector (see the preceding figure) connects to the case-mounted suspend switch. 19) A TX Power Switch / Soft-Off Switch Lead (2-pin) The system power is controlled by a momentary switch connected to this lead. Pushing the button once switches the system between ON and SLEEP or ON and SOFT OFF , depending on your BIOS or OS setting. Pushing the switch while in the ON mode for more than 4 seconds turns the system of f. The system power LED shows the status of the system power . 20) Reset Switch Lead (2-pin) This 2-pin connector connects to the case-mounted reset switch for rebooting your computer without having to turn of f your power switch. This is a preferred method of rebooting to prolong the life of the system power supply . 21) System Power LED Lead (3-1 pin) This 3-1 pin connector connects to the system power LED that lights up when the system is powered on and blinks when it is in sleep or soft-of f mode. This feature can be programmed through the ASUS ASIC. 22) SMI Lead (2-pin) This 2-pin connector connects to a panel button to allow a non-mask interrupt command to be sent to the operating system. 23) System W arning Speaker Lead (4-pin) This 4-pin connector connects to the case-mounted speaker . 24) IDE Activity LED (2-pin) This connector supplies power to the IDE activity LED. Read and write activity by devices connected to the Primary or Secondary IDE connectors cause this LED to light up. Refer to the following P ANEL illustration for items 16-24. TR-DLSR TR-DLSR System Panel Connectors Pin Connector 1 & 12 NIC Activity LED 3 & 4 Status LED 4 & 5 SMI Lead 6 & 7* Power Button 7* & 8 Chassis Intrusion 9 & 10 Reset Switch 1 1 & 13 Power LED 15* & 16 NMI Button 17 & 20 Speaker 18 & 19 HDD Access LED * Shared Chassis intrude GND SMI# buttton/sleep# button NIC activity LED Power LED HDD access LED – Status LED – Status LED RESET button GND 5V HDD access LED Power LED – GND Speaker NIC activity LED – Power button GND 11 0 11 2 0 NMI button Key
38 3. HARDW ARE SETUP ASUS TR-DLSR User ’ s Manual 3. H/W SETUP Connectors 3.9 Starting Up the First T ime 1. After making all the connections, replace the system case cover . 2. Be sure that all switches are of f (in some systems, marked with ). 3. Connect the power cord to the power connector at the back of the system chassis. 4. Connect the power cord to a power outlet that is equipped with a sur ge protector . 5. T urn on the devices in the following order: a. Monitor b. External SCSI devices (starting with the last device on the chain) c. System power (For A TX power supplies, you need to switch on the power supply as well as press the A TX power switch on the front of the chassis.) 6. The power LED on the front panel of the system case lights up. For A TX power supplies, the system LED lights up when you press the A TX power switch. If the monitor complies with “ green” standards or if it has a power standby feature,the monitor LED may light up or switch between orange and green after the system LED does. The system then runs the power -on tests. While the tests are running, the BIOS beeps or additional messages appear on the screen. If you do not see anything within 30 seconds from the time you turn on the power , the system may have failed a power -on test. Check the jumper settings and connections or call your retailer for assistance. A ward BIOS Beep Codes Beep Meaning One short beep when No error during POST displaying logo Long beeps in an endless loop No DRAM installed or detected One long beep followed by V ideo card not found or video card three short beeps memory bad High frequency beeps when CPU overheated system is working System running at a lower frequency 7. At power on, hold down <Delete> to enter BIOS Setup. Follow the instructions in 4. BIOS SETUP . * Powering Off the computer: Y ou must first exit or shut down the system before switching of f the power switch. For A TX power supplies, you can press the A TX power switch after exiting or shutting down the operating system. If you use W indows 9X, click the Start button, click Shut Down, then click Shut down the computer? The power supply should turn of f after W indows shuts down. NOTE: The message “ Y ou can now safely turn of f your computer ” does not appear when shutting dow n with A TX power supplies. 3. H/W SETUP Starting Up
ASUS TR-DLSR User ’ s Manual 39 4. BIOS SETUP 4. BIOS SETUP Updating BIOS 4.1 Managing and Updating Y our BIOS 4.1.1 Upon First Use of the Computer System It is recommended that you save a copy of the original motherboard BIOS along with a Flash Memory W riter utility (AFLASH.EXE) to a bootable floppy disk in case you need to reinstall the BIOS later . AFLASH.EXE is a Flash Memory W riter utility that updates the BIOS by uploading a new BIOS file to the programmable flash ROM on the motherboard. This file works only in DOS mode. T o determine the BIOS version of your motherboard, check the last four numbers of the code displayed on the upper left-hand corner of your screen during bootup. Larger numbers represent a newer BIOS file. 1. T ype FORMA T A:/S at the DOS prompt to create a bootable system disk. DO NOT copy AUTOEXEC.BA T and CONFIG.SYS to the disk. 2. T ype COPY D:\AFLASH\AFLASH.EXE A:\ (assuming D is your CD-ROM drive) to copy AFLASH.EXE to the boot disk you created. NOTE: AFLASH works only in DOS mode. It does not work in the DOS prompt within W indows and does not work with certain memory drivers that may be loaded when you boot from the hard drive. It is recommended that you reboot using a floppy disk. 3. Reboot the computer from the floppy disk. NOTE: BIOS setup must specify “ Floppy” as the first item in the boot sequence. 4. In DOS mode, type A:\AFLASH <Enter> to run AFLASH. IMPORT ANT! If the word “ unknown” appears after Flash Memory:, the memory chip is either not programmable or is not supported by the ACPI BIOS and therefore, cannot be programmed by the Flash Memory W riter utility . 4. BIOS SETUP
ASUS TR-DLSR User ’ s Manual 40 4. BIOS SETUP 4. BIOS SETUP Updating BIOS 5. Select 1. Save Current BIOS to File from the Main menu and press <Enter>. The Save Curr ent BIOS T o File screen appears. 6. T ype a filename and the path, for example, A:\XXX-XX.XXX and then press <Enter>.
ASUS TR-DLSR User ’ s Manual 41 4. BIOS SETUP 4. BIOS SETUP Updating BIOS 4.1.2 Updating BIOS Procedures 1. Download an updated ASUS BIOS file from the Internet (WWW or FTP) (see ASUS CONT ACT INFORMA TION on page 3 for details) and save to the boot floppy disk you created earlier . 2. Boot from the floppy disk. 3. At the “ A:\” prompt, type AFLASH and then press <Enter>. 4. At the Main Menu, type 2 then press <Enter>. The Update BIOS Including Boot Block and ESCD screen appears. 5. T ype the filename of your new BIOS and the path, for example, A:\XXX- XX.XXX , then press <Enter>. NOTE: T o cancel this operation, press <Enter>. 6. When prompted to confirm the BIOS update, press Y to start the update. W ARNING! Update the BIOS only if you have problems with the motherboard and you know that the new BIOS revision will solve your problems. Careless updating can result to more problems with the motherboard!
ASUS TR-DLSR User ’ s Manual 42 4. BIOS SETUP 4. BIOS SETUP 7. The utility starts to program the new BIOS information into the Flash ROM. The boot block is updated automatically only when necessary . This minimizes the possibilities of boot problems in case of update failures. When the programming is done, Flashed Successfully appears. 8. Follow the onscreen instructions to continue. W ARNING! If you encounter problems while updating the new BIOS, DO NOT turn off the system because this may cause boot problems. Just repeat the process, and if the problem still persists, load the original BIOS file you saved to the boot disk. If the Flash Memory W riter utility is not able to successfully update a complete BIOS file, the system may not boot. If this happens, call the ASUS service center for support. Updating BIOS
ASUS TR-DLSR User ’ s Manual 43 4. BIOS SETUP 4. BIOS SETUP NOTE: Because the BIOS software is constantly being updated, the following BIOS setup screens and descriptions are for reference purposes only , and may not exactly match what you see on your screen. 4.2 BIOS Setup Program This motherboard supports a programmable EEPROM that you can update using the provided utility described in 4.1 Managing and Updating Y our BIOS . The utility is used if you are installing a motherboard, reconfiguring your system, or prompted to “ Run Setup ”. This section describes how to configure your system using this utility . Even if you are not prompted to use the Setup program, at some time in the future you may want to change the configuration of your computer . For example, you may want to enable the Security Password Feature or make changes to the power management settings. It will then be necessary to reconfigure your system using the BIOS Setup program so that the computer can recognize these changes and record them in the CMOS RAM of the EEPROM. The EEPROM on the motherboard stores the Setup utility . When you start up the computer , the system provides you with the opportunity to run this program. This appears during the Power -On Self T est (POST). Press <Delete> to call up the Setup utility . If you are a little bit late in pressing the mentioned key , POST will continue with its test routines, thus preventing you from calling up Setup. If you still need to call Setup, restart the system by pressing <Ctrl> <Alt> <Delete>, or by pressing the Reset button on the system chassis. Y ou can also restart by turning the system off and then back on again. But do so only if the first two methods fail. The Setup program has been designed to make it as easy to use as possible. It is a menu-driven program, which means you can scroll through the various sub-menus and make your selections among the predetermined choices. To access the BIOS Setup program, press the <Delete> key after the computer has run through its POST. Program Information
ASUS TR-DLSR User ’ s Manual 44 4. BIOS SETUP 4. BIOS SETUP Program Information 4.2.1 BIOS Menu Bar The top of the screen has a menu bar with the following selections: MAIN Use this menu to make changes to the basic system configuration. ADV ANCED Use this menu to enable and make changes to the advanced features. POWER Use this menu to configure and enable Power Management features. BOOT Use this menu to configure the default system device used to locate and load the Operating System. EXIT Use this menu to exit the current menu or specify how to exit the Setup program. T o access the menu bar items, press the right or left arrow key on the keyboard until the desired item is highlighted. 4.2.2 Legend Bar At the bottom of the Setup screen is a legend bar . The keys in the legend bar allow you to navigate through the various setup menus. The following table lists the keys found in the legend bar with their corresponding functions. Navigation Key(s) Function Description <F1> or <Alt H> Displays the General Help screen from anywhere in the BIOS Setup <Esc> Jumps to the Exit menu or returns to the main menu from a sub-menu ← or → ( keypad arrow) Selects the menu item to the left or right ↑ or ↓ ( keypad arrow) Moves the highlight up or down between fields - (minus key) Scrolls backward through the values for the highlighted field (plus key) or spacebar Scrolls forward through the values for the highlighted field <Enter> Brings up a selection menu for the highlighted field <Home> or <PgUp> Moves the cursor to the first field <End> or <PgDn> Moves the cursor to the last field <F5> Resets the current screen to its Setup Defaults <F10> Saves changes and exits Setup
ASUS TR-DLSR User ’ s Manual 45 4. BIOS SETUP 4. BIOS SETUP Program Information General Help In addition to the Item Specific Help window , the BIOS setup program also provides a General Help screen. Y ou may launch this screen from any menu by simply pressing <F1> or the <Alt> <H> combination. The General Help screen lists the legend keys with their corresponding functions. Saving Changes and Exiting the Setup Program See 4.7 Exit Menu for detailed information on saving changes and exiting the setup program. Scroll Bar When a scroll bar appears to the right of a help window , it indicates that there is more information to be displayed that will not fit in the window . Use <PgUp> and <PgDn> or the up and down arrow keys to scroll through the entire help document. Press <Home> to display the first page, press <End> to go to the last page. T o exit the help window , press <Enter> or <Esc>. Sub-Menu Note that a right pointer symbol (as shown in the left view) appears to the left of certain fields. This pointer indicates that you can display a sub-menu from this field. A sub-menu contains additional options for a field parameter . T o display a sub-menu, move the highlight to the field and press <Enter>. The sub-menu appears. Use the legend keys to enter values and move from field to field within a sub-menu as you would within a menu. Use the <Esc> key to return to the main menu. T ake some time to familiarize yourself with the legend keys and their corresponding functions. Practice navigating through the various menus and sub-menus. If you accidentally make unwanted changes to any of the fields, use the set default hot key <F5> to load the Setup default values. While moving around through the Setup program, note that explanations appear in the Item Specific Help window located to the right of each menu. This window displays the help text for the currently highlighted field. NOTE: The item heading in square brackets represents the default setting for that field.
ASUS TR-DLSR User ’ s Manual 46 4. BIOS SETUP 4. BIOS SETUP Main Menu System Time [XX:XX:XX] Sets your system to the time that you specify (usually the current time). The format is hour , minute, second. V alid values for hour , minute and second are Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59) . Use the <T ab> or <Shift> <T ab> keys to move between the hour , minute, and second fields. System Date [XX/XX/XXXX] Sets your system to the date that you specify (usually the current date). The format is month, day , year . V alid values for month, day , and year are Month: (1 to 12), Day: (1 to 31), Y ear: ( 100 year range ) . Use the <T ab> or <Shift> <T ab> keys to move between the month, day , and year fields. Legacy Diskette A [1.44M, 3.5 in.], Legacy Diskette B [None] Sets the type of floppy drives installed. Configuration options: [None] [360K, 5.25 in.] [1.2M , 5.25 in.] [720K , 3.5 in.] [1.44M, 3.5 in.] [2.88M, 3.5 in.] 4.3 Main Menu When the Setup program is accessed, the following screen appears:
ASUS TR-DLSR User ’ s Manual 47 4. BIOS SETUP 4. BIOS SETUP Master/Slave Devices NOTE: Before attempting to configure a hard disk drive, make sure you have the configuration information supplied by the manufacturer of the drive. Incorrect settings may cause your system to not recognize the in- stalled hard disk. T o allow the BIOS to detect the drive type automati- cally , select [Auto]. Type [Auto] Select [Auto] to automatically detect an IDE hard disk drive. If automatic detection is successful, the correct values will be filled in for the remaining fields on this sub-menu. If automatic detection fails, your hard disk drive may be too old or too new . Y ou can try updating your BIOS or enter the IDE hard disk drive parameters manually . NOTE: After the IDE hard disk drive information has been entered into BIOS, new IDE hard disk drives must be partitioned (such as with FDISK) and then formatted before data can be read from and write on. Primary IDE hard disk drives must have its partition set to active (also possible with FDISK). Other options for the T ype field are: [None] - to disable IDE devices 4.3.1 Primary & Secondary Master/Slave
ASUS TR-DLSR User ’ s Manual 48 4. BIOS SETUP 4. BIOS SETUP Master/Slave Devices [User Type HDD] Manually enter the number of cylinders, heads and sectors per track for your drive. Refer to your drive documentation or look on the drive for this information. If no drive is installed or if you are removing a drive and not replacing it, select [ None] . T ranslation Method [LBA] Select the hard disk drive type in this field. When Logical Block Addressing is enabled, 28-bit addressing of the hard drive is used without regard for cylinders, heads, or sectors. Note that LBA Mode is necessary for drives with greater than 504MB in storage capacity . Configuration options: [LBA] [LARGE] [Normal] [Match Partition T able] [Manual] Cylinders This field configures the number of cylinders. Refer to your drive documentation to determine the correct value to enter into this field. NOTE: T o make changes to this field, the T ype field must be set to [User T ype HDD] and the T ranslation Method field must be set to [Manual]. IMPORT ANT : If the hard disk was already formatted on an older system, Setup may detect incorrect parameters. Y ou will need to enter the correct parameters manually , or use low-level format in case you do not need the data stored on the hard disk. If the parameters listed differ from the ones used when the disk was formatted, the disk will not be readable. If the auto-detected parameters do not match the ones that should be used for the disk, you should enter the correct ones manually by setting [User T ype HDD].
ASUS TR-DLSR User ’ s Manual 49 4. BIOS SETUP 4. BIOS SETUP Master/Slave Devices Head This field configures the number of read/write heads. Refer to your drive documentation to determine the correct value to enter into this field. NOTE: T o make changes to this field, the T ype field must be set to [User T ype HDD] and the T ranslation Method field must be set to [Manual]. Sector This field configures the number of sectors per track. Refer to your drive documentation to determine the correct value to enter into this field. NOTE: T o make changes to this field, the T ype field must be set to [User T ype HDD] and the T ranslation Method field must be set to [Manual]. CHS Capacity This field shows the drive ’ s maximum CHS capacity calculated automatically by the BIOS from the drive information you entered. Maximum LBA Capacity This field shows the drive ’ s maximum LBA capacity calculated automatically by the BIOS from the drive information you entered. Multi-Sector T ransfers [Maximum] This option automatically sets the number of sectors per block to the highest number supported by the drive. This field can also be configured manually . Note that when this field is automatically configured, the set value may not always be the fastest value for the drive. Refer to the documentation that came with your hard drive to determine the optimal value and set it manually . NOTE: T o make changes to this field, the T ype field must be set to [User T ype HDD]. Configuration options: [Disabled] [2 Sectors] [4 Sectors] [8 Sectors] [16 Sectors] [32 Sectors] [Maximum] SMAR T Monitoring [Disabled] This allows the enabling or disabling of the S.M.A.R.T . (Self-Monitoring, Analysis and Reporting T echnology) system which utilizes internal hard disk drive monitoring technology . This feature is normally disabled because system resources used in this feature may decrease system performance. Configuration options: [Disabled] [Enabled] PIO Mode [4] This option lets you set a PIO (Programmed Input/Output) mode for the IDE device. Modes 0 through 4 provide successively increased performance. Configuration options: [0] [1] [2] [3] [4] Ultra DMA Mode [Disabled] Ultra DMA capability allows improved transfer speeds and data integrity for compatible IDE devices. Set to [Disabled] to suppress Ultra DMA capability . NOTE: T o make changes to this field, the T ype field must be set to [User T ype HDD]. Configuration options vary according to your device.
ASUS TR-DLSR User ’ s Manual 50 4. BIOS SETUP 4. BIOS SETUP Keyboard Features [CD-ROM] - for IDE CD-ROM drives [LS-120] - for LS-120 compatible floppy disk drives [ZIP-100] - for ZIP-100 compatible disk drives [MO] - for IDE magneto optical disk drives [Other ATAPI Device] - for IDE devices not listed here After using the legend keys to make your selections on this sub-menu, press the <Esc> key to exit back to the Main menu. When the Main menu appears, you will notice that the drive size appear in the field for the hard disk drive that you just configured. 4.3.2 Keyboard Features Boot Up NumLock Status [On] This field enables users to activate the Number Lock function upon system boot. Configuration options: [Off] [On] Keyboard Auto-Repeat Rate [12/Sec] This controls the speed at which the system registers repeated keystrokes. Options range from 6 to 30 characters per second. Configuration options: [6/Sec] [8/Sec] [10/Sec] [12/Sec] [15/Sec] [20/Sec] [24/Sec] [30/Sec] Keyboard Auto-Repeat Delay [1/4 Sec] This field sets the time interval for displaying the first and second characters. Configuration options: [1/4 Sec] [1/2 Sec] [3/4 Sec] [1 Sec]
ASUS TR-DLSR User ’ s Manual 51 4. BIOS SETUP 4. BIOS SETUP Main Menu Language [English] This allows selection of the BIOS ’ displayed language. Currently only English is available. Supervisor Password [Disabled] / User Password [Disabled] These fields allow you to set the passwords. T o set the password, highlight the appropriate field and press <Enter>. T ype in a password and press <Enter>. Y ou can type up to eight alphanumeric characters. Symbols and other keys are ignored. T o confirm the password, type the password again and press the <Enter>. The password is now set to [Enabled]. This password allows full access to the BIOS Setup menus. T o clear the password, highlight this field and press <Enter>. The same dialog box as above will appear . Press <Enter> and the password will be set to [Disabled]. A Note about Passwords The BIOS Setup program allows you to specify passwords in the Main menu. The passwords control access to the BIOS during system startup. The passwords are not case sensitive. In other words, it makes no dif ference whether you enter a password using upper or lowercase letters. The BIOS Setup program allows you to specify two separate passwords: a Supervisor password and a User password. When disabled, anyone may access all BIOS Setup program functions. When enabled, the Supervisor password is required for entering the BIOS Setup program and having full access to all configuration fields. Forgot the Password? If you forgot the password, you can clear the password by erasing the CMOS Real T ime Clock (R TC) RAM. The RAM data containing the password information is powered by the onboard button cell battery . T o erase the R TC RAM: (1) Unplug your computer , (2) Remove the battery , (3) Short the solder points, (4) Re- install the battery , (5) T urn ON your computer , (6 ) Hold down <Delete> during bootup and enter BIOS setup to re-enter CMOS data. TR-DLSR TR-DLSR Clear RTC RAM Short solder points to Clear CMOS R323 Halt On [All Errors] This field determines which types of errors will cause the system to halt. Configuration options: [All Errors] [No Error] [All but Keyboard] [All but Disk] [All but Disk/Keyboard] Installed Memory [XXX MB] This display-only field displays the amount of conventional memory detected by the system during bootup. Y ou do not need to make changes to this field.
ASUS TR-DLSR User ’ s Manual 52 4. BIOS SETUP 4. BIOS SETUP Advanced Menu 4.4 Advanced Menu CPU Level 1 Cache, CPU Level 2 Cache [Enabled] These fields allow you to choose from the default of [Enabled] or choose [Disabled] to turn on or off the CPU ’ s Level 1 and Level 2 built-in cache. Configuration options: [Disabled] [Enabled] CPU Level 2 Cache ECC Check [Disabled] This function controls the ECC capability in the CPU level 2 cache. Con- figuration options: [Disabled] [Enabled] Processor Serial Number [Disabled] The Processor Serial Number is a unique number that is added to every Pentium III processor to help verify the identity of the user across the Internet. Set this field to [Enabled] when you need increased security for doing business online or e-commerce. Otherwise, leave it to its default setting of [Disabled] for greater anonymity when surfing the Internet. NOTE: This field is available only when a Pentium III processor is installed in your system. BIOS Update [Enabled] This functions as an update loader integrated into the BIOS to supply the processor with the required data. In the default position of [Enabled], the BIOS will load the update on all processors during system bootup. Configu- ration options: [Disabled] [Enabled]
ASUS TR-DLSR User ’ s Manual 53 4. BIOS SETUP 4. BIOS SETUP Advanced Menu PS/2 Mouse Function Control [Auto] The default of [Auto] allows the system to detect a PS/2 mouse on startup. If detected, IRQ12 will be used for the PS/2 mouse. IRQ12 will be reserved for expansion cards only if a PS/2 mouse is not detected. [Enabled] will always reserve IRQ12, whether on startup a PS/2 mouse is detected or not. Configuration options: [Enabled] [Auto] OS/2 Onboard Memory > 64M [Disabled] When using OS/2 operating systems with installed DRAM of greater than 64MB, you need to set this option to [Enabled]; otherwise, leave this on [Disabled]. Configuration options: [Disabled] [Enabled]
ASUS TR-DLSR User ’ s Manual 54 4. BIOS SETUP 4. BIOS SETUP Chip Configuration 4.4.1 Chip Configuration Video Memory Cache Mode [UC] USWC (uncacheable, speculative write combining) is a new cache technology for the video memory of the processor . It can greatly improve the display speed by caching the display data. Y ou must set this to UC (uncacheable) if your display card cannot support this feature; otherwise your system may not boot. Configuration options: [UC] [USWC] Onboard PCI IDE Enable [Both] Y ou can select to enable the primary IDE channel, both the primary and secondary channels, or disable both channels. Configuration options: [Both] [Primary] [Disabled]
ASUS TR-DLSR User ’ s Manual 55 4. BIOS SETUP 4. BIOS SETUP I/O Device Config Floppy Disk Access Control [R/W] When set to [Read Only], this field protects files from being copied to floppy disks by allowing reads from the floppy disk drive but not writes. The setup default [R/W] allows both reads and writes. Configuration options: [R/W] [Read Only] Onboard Serial Port 1 [3F8H/IRQ4] Onboard Serial Port 2 [2F8H/IRQ3] These fields allow you to set the addresses for the onboard serial connectors. Serial Port 1 and Serial Port 2 must have dif ferent addresses. Configuration options: [3F8H/IRQ4] [2F8H/IRQ3] [3E8H/IRQ4] [2E8H/IRQ10] [Disabled] Onboard Parallel Port [378H/IRQ7] This field sets the address of the onboard parallel port connector . If you disable this feature, Parallel Port Mode and ECP DMA Select configurations will not be available. Configuration options: [Disabled] [378H/IRQ7] [278H/IRQ5] Parallel Port Mode [ECP EPP] This field allows you to set the operation mode of the parallel port. [Normal] allows normal-speed operation but in one direction only; [EPP] allows bidirectional parallel port operation; [ECP] allows the parallel port to operate in bidirectional DMA mode; [ECP EPP] allows normal speed operation in a two-way mode. Configuration options: [Normal] [EPP] [ECP] [ECP EPP] 4.4.2 I/O Device Configuration
ASUS TR-DLSR User ’ s Manual 56 4. BIOS SETUP 4. BIOS SETUP 4.4.3 PCI Configuration PCI Configuration ECP DMA Select [3] This field allows you to configure the parallel port DMA channel for the selected ECP mode. This selection is available only if you select [ECP] or [ECP EPP] in Parallel Port Mode above. Configuration options: [1] [3] [Disabled] Slot 1, Slot 2, Slot 3 IRQ [Auto] These fields set how IRQ use is determined for each PCI slot. The default setting for each field is [Auto], which utilizes auto-routing to determine IRQ use. Configuration options: [Auto] [NA] [3] [4] [5] [7] [9] [10] [1 1] [12] [14] [15] PCI Latency Timer [32] Leave on default setting for best performance vs. stability . Onboard SCSI BIOS [Auto] [Auto ] allows the motherboard ’ s BIOS to detect whether you have a Symbios SCSI controller . If the Symbios SCSI controller is detected, the motherboard ’ s Symbios BIOS will be enabled ; if no Symbios SCSI controller is detected, the onboard Symbios SCSI BIOS will be disabled. [Disabled] will disable the motherboard ’ s Symbios SCSI BIOS so that the BIOS on an add-on Symbios SCSI card can be used. If your Symbios SCSI card does not have a BIOS, the Symbios SCSI card will not function. Configuration options: [Auto] [Disabled]
ASUS TR-DLSR User ’ s Manual 57 4. BIOS SETUP 4. BIOS SETUP PCI Configuration ONB SCSI BIOS First [No] This field allows giving priority to the onboard SCSI BIOS for SCSI functions over other SCSI controllers. Configuration options: [No] [Y es] ONB Primary SCSI Term, ONB Secondary SCSI Term [Enabled] These fields allow you to enable or disable the onboard SCSI termination on the primary and secondary SCSI channels. Configuration options: [Enabled] [Disabled] USB Function [Enabled] Set this field to [Enabled] if you want to use Universal Serial Bus devices. Configuration options: [Disabled] [Enabled] ONB VGA BIOS First [No] This field, when set to [Y es], gives priority to the onboard VGA BIOS over other VGA controllers. Configuration options: [No] [Y es] Onboard LAN Boot ROM [Disabled] When set to [Enabled], this field allows your computer to boot from the network using the onboard LAN controller boot ROM. Configuration options: [Disabled] [Enabled]
ASUS TR-DLSR User ’ s Manual 58 4. BIOS SETUP 4. BIOS SETUP Shadow Configuration Video ROM BIOS Shadow [Enabled] This field allows you to change the video BIOS location from ROM to RAM. Relocating to RAM enhances system performance, as information access is faster than the ROM. Configuration options: [Disabled] [Enabled] C8000-DFFFF Shadow [Disabled] These fields are used for shadowing other expansion card ROMs. If you install other expansion cards with ROMs on them, you will need to know which addresses the ROMs use to shadow them specifically . Shadowing a ROM reduces the memory available between 640K and 1024K by the amount used for this purpose. Configuration options: [Disabled] [Enabled] 4.4.4 Shadow Configuration
ASUS TR-DLSR User ’ s Manual 59 4. BIOS SETUP 4. BIOS SETUP Power Menu 4.5 Power Menu The Power menu allows you to reduce power consumption. This feature turns off the video display and shuts down the hard disk after a period of inactivity . Power Management [User Define] This option must be enabled to use any of the automatic power saving features. If this menu item is set to [Disabled], power management features will not function regardless of other field settings on this menu. The [User Define] option allows you to make your own selections in the Power menu. When set to [Max Saving], system power will be conserved to its greatest amount. The Suspend Mode field will then be set to predefined value that ensures maximum power savings. This field acts as the master control for the power management modes. [Max Saving] puts the system into power saving mode after a brief period of system inactivity; [Min Saving] is almost the same as [Max Saving] except that the system inactivity period is longer; [Disabled] disables the power saving features; [User Define] allows you to set power saving options according to your preference. Configuration options: [User Define] [Disabled] [Min Saving] [Max Saving] IMPORT ANT : Advanced Power Management (APM) should be installed to keep the system time updated when the computer enters suspend mode activated by the BIOS Power Management. For DOS environments, you need to add the statement, DEVICE=C:\DOS\POWER.EXE, to your CONFIG.SYS file. For W indows 3.x and W indows 95, you need to install W indows with the APM feature. For W indows 98 and later , APM is automatically installed. A battery and power cord icon labeled “ Power Management ” will appear in the “ Control Panel. ” Choose “Advanced ” in the Power Management Properties dialog box.
ASUS TR-DLSR User ’ s Manual 60 4. BIOS SETUP 4. BIOS SETUP Power Menu Video Off Option [Suspend -> Off ] This field determines when to activate the video of f feature for monitor power management. Configuration options: [Always On] [Suspend -> Of f] Video Off Method [DPMS OFF] This field defines the video off features. The DPMS (Display Power Management System) feature allows the BIOS to control the video display card if it supports the DPMS feature. [Blank Screen] only blanks the screen (use this for monitors without power management or “ green ” features. If set up in your system, your screen saver will not display with [Blank Screen] selected). [V/H SYNC Blank] blanks the screen and turns of f vertical and horizontal scanning. Configuration options: [Blank Screen] [V/H SYNC Blank] [DPMS Standby] [DPMS Suspend] [DPMS OFF] [DPMS Reduce ON] HDD Power Down [Disabled] Shuts down any IDE hard disk drives in the system after a period of inactivity as set in this user-configurable field. This feature does not affect SCSI hard drives. Configuration options: [Disabled] [1 Min] [2 Min] [3 Min]...[15 Min] Suspend Mode [Disabled] This sets the time period before the system goes into suspend mode. Configuration options: [Disabled] [1~2 Min] [2~3 Min]...[1 Hour]
ASUS TR-DLSR User ’ s Manual 61 4. BIOS SETUP 4. BIOS SETUP Power Up Control AC PWR Loss Restart [Disabled] This allows you to set whether you want your system to reboot after the power has been interrupted. [Disabled] leaves your system of f and [Enabled] resets your system. Configuration options: [Disabled] [Enabled] PWR Up On Modem Act [Enabled] This allows either settings of [Enabled] or [Disabled] for powering up the computer when the modem receives a call while the computer is in Soft-of f mode. NOTE: The computer cannot receive or transmit data until the computer and applications are fully running. Thus connection cannot be made on the first try . T urning an external modem off and then back on while the computer is of f causes an initialization string that will also cause the system to power on. Configuration options: [Disabled] [Enabled] Wake On LAN [Disabled] W ake-On-LAN allows your computer to be booted from another computer via a network by sending a wake-up frame or signal. Configuration options: [Disabled] [Enabled] 4.5.1 Power Up Control IMPORT ANT : This feature requires an optional network interface card with W ake- On-LAN and an A TX power supply with at least 720mA 5V standby power .
ASUS TR-DLSR User ’ s Manual 62 4. BIOS SETUP 4. BIOS SETUP Power Up Control Automatic Power Up [Disabled] This allows an unattended or automatic system power up. Y ou may configure your system to power up at a certain time of the day by selecting [Everyday] or at a certain time and day by selecting [By Date]. NOTE: Automatic Power Up will not work if the system is powered down by operating systems, such as W indows 98, which have ACPI support enabled. Configuration options: [Disabled] [Everyday] [By Date]
ASUS TR-DLSR User ’ s Manual 63 4. BIOS SETUP 4. BIOS SETUP Hardware Monitor 4.5.2 Hardware Monitor MB Temperature [xxxC/xxxF] CPU1 Temperature [xxxC/xxxF] CPU2 Temperature [xxxC/xxxF] The onboard hardware monitor is able to detect the MB (motherboard) and CPU temperatures. Set to [Ignore] only if necessary . CPU1 Fan Speed [xxxxRPM] CPU2 Fan Speed [xxxxRPM] Chassis1 Fan Speed [xxxxRPM] Chassis2 Fan Speed [xxxxRPM] The onboard hardware monitor is able to detect the CPU fan speed and the chassis fan speed in rotations per minute (RPM). The presence of the fans is automatically detected. Set to [Ignore] only if necessary . VCORE1 Voltage, VCORE2 Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage , -12V Voltage, -5V Voltage [xx.xV] The onboard hardware monitor is able to detect the voltage output by the onboard voltage regulators. Set to [Ignore] only if necessary . NOTE: If any of the monitored items is out of range, an error message will appear: “ Hardware Monitor found an error . Enter Power setup menu for details ” . Y ou will then be prompted to “ Press F1 to continue, DEL to enter SETUP ”.
ASUS TR-DLSR User ’ s Manual 64 4. BIOS SETUP 4. BIOS SETUP Boot Menu Boot Sequence The Boot menu allows you to select among the four possible types of boot devices listed using the up and down arrow keys. By using the < > or <Space> key , you can promote devices and by using the <-> key , you can demote devices. Promotion or demotion of devices alters the priority which the system uses to search for a boot device on system power up. Configuration fields include Removable Devices , IDE Hard Drive , A T API CD-ROM , and Other Boot Device . Removable Device [Legacy Floppy] Configuration options: [Disabled] [Legacy Floppy] [LS120] [ZIP-100] [A T API MO] IDE Hard Drive This field allows you to select which IDE hard disk drive to use in the boot sequence. Pressing [Enter] will show the product IDs of all connected IDE hard disk drives. ATAPI CD-ROM This field allows you to select which A T API CD-ROM drive to use in the boot sequence. Pressing [Enter] will show the product IDs of all your connected A T API CD-ROM drives. 4.6 Boot Menu
ASUS TR-DLSR User ’ s Manual 65 4. BIOS SETUP 4. BIOS SETUP Boot Menu Other Boot Device Select [INT18 Device (Network)] Configuration options: [Disabled] [SCSI Boot Device] [INT18 Device (Network)] Plug & Play O/S [No] This field allows you to use a Plug-and-Play (PnP) operating system to configure the PCI bus slots instead of using the BIOS. When [Y es] is selected, interrupts may be reassigned by the OS. When a non-PnP OS is installed or you want to prevent reassigning of interrupt settings, select the default setting of [No]. Configuration options: [No] [Y es] MPS 1.4 Support [Enabled] This field allows you to enable or disable the MultiProcessor Specification 1.4 support. Configuration options: [Disabled] [Enabled] Boot Virus Detection [Enabled] This field allows you to set boot virus detection, ensuring a virus-free boot sector . The system halts and displays a warning message when it detects a virus. If this occurs, you can either allow the operation to continue or use a virus-free bootable floppy disk to restart and investigate your system. Configuration options: [Disabled] [Enabled] Quick Power On Self Test [Enabled] This field speeds up the Power-On-Self T est (POST) routine by skipping retesting a second, third, and fourth time. Configuration options: [Disabled] [Enabled] Boot Up Floppy Seek [Enabled] When enabled, the BIOS seeks the floppy disk drive once during bootup. Configuration options: [Disabled] [Enabled]
ASUS TR-DLSR User ’ s Manual 66 4. BIOS SETUP 4. BIOS SETUP Exit Menu Exit Saving Changes Once you are finished making your selections, choose this option from the Exit menu to ensure the values you selected are saved to the CMOS RAM. The CMOS RAM is sustained by an onboard backup battery and stays on even when the PC is turned off. Once this option is selected, a confirmation is asked. Select [Y es] to save changes and exit. NOTE: If you attempt to exit the Setup program without saving your changes, the program will prompt you with a message asking if you want to save your changes before exiting. Pressing <Enter> will then save changes while exiting. Exit Discarding Changes This option should only be used if you do not want to save the changes you have made to the Setup program. If you have made changes to fields other than system date, system time, and password, the system will ask for confirmation before exiting. 4.7 Exit Menu Once you have made all of your selections from the various menus in the Setup program, you should save your changes and exit Setup. Select Exit from the menu bar to display the following menu: NOTE: Pressing <Esc> does not exit this menu. Y ou must select one of the options from this menu or <F10> from the legend bar to exit this menu.
ASUS TR-DLSR User ’ s Manual 67 4. BIOS SETUP 4. BIOS SETUP Exit Menu Load Setup Defaults This option allows you to load the default values for each of the parameters on the Setup menus. When this option is selected or if <F5> is pressed, a confirmation is requested. Select [Y es] to load default values. Y ou can now select Exit Saving Changes or make other changes before saving the values to the non-volatile RAM. Discard Changes This option allows you to discard the selections you made and restore the values you previously saved. After selecting this option, a confirmation is requested. Select [Y es] to discard any changes and load the previously saved values. Save Changes This option saves your selections without exiting the Setup program. Y ou can then return to other menus and make changes. After selecting this option, all selections are saved and a confirmation is requested. Select [Y es] to save any changes to the non-volatile RAM.
ASUS TR-DLSR User ’ s Manual 68 4. BIOS SETUP 4. BIOS SETUP
® TR-DLSR Dual Socket 370 Motherboard 5. OS Driver Installation
70 ASUS TR-DLSR User ’ s Manual Contents 1. Micr osoft W indows NT Server .................................................. 73 I. LSI SCSI Driver Installation ..................................................... 73 A. Preparing a LSI Driver Diskette ......................................... 73 B. New System Installation ..................................................... 73 B1. CD-ROM Installation ........................................................ 74 B2. Boot Floppy Disk Installation ........................................... 74 C. Existing System Installation ................................................ 75 II. Intel 82559 Network Driver Installation ................................. 76 A. Preparing Intel 82559 Lan Driver Diskette ......................... 76 B. New System Installation ..................................................... 76 C. Existing System Installation ................................................ 77 III. A TI Rage XL Display Driver Installation ............................... 78 2. Micr osoft W indows 2000 Server ................................................ 79 I. LSI SCSI Driver Installation ..................................................... 79 A. Preparing a LSI Driver Diskette ......................................... 79 B. New System Installation ..................................................... 79 C. Existing System Installation ................................................ 80 II. Intel 82559 Network Driver Installation ................................. 82 A. Preparing Intel 82559 Lan Driver Diskette ......................... 82 B. Update Driver on an Existing System Installation .............. 82 III. A TI Rage XL Display Driver Installation ............................... 84 3. Novell NetW are Server ............................................................... 85 I. LSI SCSI Driver Installation ..................................................... 85 A. Preparing a LSI Driver Diskette ......................................... 85 B. NetW are 5.XX New Installations ........................................ 85 C. NetW are 4.XX New Installations ........................................ 86 II. Intel 82559 Network Driver Installation ................................. 87 A. Preparing Intel 82559 Lan Driver Diskette ......................... 87 B. NetW are 4.XX & 5.X Installations ..................................... 87 III. A TI Rage XL Display Driver Installation ............................... 88 4. SUN Solaris X86 Server ............................................................. 89 I. LSI SCSI Driver Installation ..................................................... 89 A. Building the SYMHISL Driver Update Diskette ................ 89 B. New System Installation ..................................................... 89 C. Existing System Installation ................................................ 92 II. Intel 82559 Network Driver Installation ................................. 93 III. A TI Rage XL Display Driver Installation ............................... 93 5. Driver Installation T able of Contents
ASUS TR-DLSR User ’ s Manual 71 Contents 5. Driver Installation T able of Contents 5. SCO Open Server 5.0.x ............................................................... 94 I. LSI SCSI Driver Installation ..................................................... 94 A. Building the SCO OpenServer BTLD Diskette .................. 94 B. New System Installation ..................................................... 95 C. Existing System Installation ................................................ 95 II. Intel 82559 Network Driver Installation ................................. 96 III. A TI Rage XL Display Driver Installation ............................... 96 6. SCO UnixW are Server ............................................................... 97 I. LSI SCSI Driver Installation ..................................................... 97 A. Building the SCO UnixW are C8XX BTLD Diskette ......... 97 B. New System Installation ..................................................... 98 C. Existing System Installation ................................................ 98 II. Intel 82559 Network Driver Installation ................................. 99 III. A TI Rage XL Display Driver Installation ............................... 99 7. Linux RedHat 6.x and 7.x ........................................................ 100 I. LSI SCSI Driver Installation ................................................... 100 II. Intel 82559 Network Driver Installation ............................... 100 III. A TI Rage XL Display Driver Installation ............................. 100
72 ASUS TR-DLSR User ’ s Manual
ASUS TR-DLSR User ’ s Manual 73 5. OS Driver Installation 5. Driver Installation WinNT4.0 Server 1. Microsoft W indows NT Server I. LSI SCSI Driver Installation LSI Logic and Microsoft together provided miniport drivers, “ SYM_HI.SYS” (for SYM53C896) and “ LSI_U3.SYS” ( for SYM53C1010) . The SCSI chipset used on your motherboard will depend on the model you purchased. The following sections describe how to prepare and install the SCSI drivers. Since W indows NT 4.0 do not have drivers for such new SCSI controllers, the user must load the driver manually prior to W indows NT 4.0 installation. A. Preparing a LSI Driver Diskette The drivers are located on the ASUS Driver Support CD at: \SDMS\DRIVERS\WINNT\ XXXXX\I386\WINNT\MINIPOR T where XXXXX represents the specific W indows NT subdirectory . For example, the SYM_HI.SYS driver is located in the WINNTHI subdirectory . Copy the I386 and MINIPOR T subdirectories to the root directory of a clean floppy diskette. Use this driver diskette during W indows NT installation. (-or -) Use the self-extracting image files for W indows NT drivers. The SYM_HI.SYS executable driver is located on the ASUS Driver Support CD at: \SDMS\DISKIMAG\NT_HI The LSI_U3.SYS executable driver is located on the ASUS Driver Support CD at: \SDMS\DISKIMAG\NT_U3 B. New System Installation This procedure installs the SYM_HI.SYS or LSI_U3.SYS driver onto a W indows NT system. Use this procedure when installing W indows NT onto an unused SCSI drive. W indows NT automatically adds the driver to the registry and copies the driver to the appropriate directory . There are two method to install the W indows NT system. One is installed by booting from NT CD Disc; the other is by booting from NT three installation floppy diskettes.
74 ASUS TR-DLSR User ’ s Manual 5. OS Driver Installation 5. Driver Installation WinNT4.0 Server B1. CD-ROM Installation 1. Start the W indows NT installation by booting from the W indows NT CD-ROM. The system BIOS must support booting from a CD-ROM. LSI BIOS settings may need to be changed to allow CD-ROM booting when using a SCSI CD- ROM drive. 2. When the screen displays “ W indows NT Setup ” , immediately press the F6 key . This must be done or else the new driver installed from the LSI driver diskette will not be recognized. Note: If F6 is not pressed, the user is still given the opportunity to load additional drivers later in the installation process. However , any driver loaded during W indows NT Setup are not immediately recognized and no devices controlled by that driver are available during W indows NT Setup. 3. When prompted for the manufacturer -supplied hardware support disk, insert the appropriate LSI driver diskette containing the W indows NT driver required to support your LSI adapter(s) and press Enter . The driver files are distributed with ASUS Driver Support CD and are created from above “Preparing a LSI Driver Diskette” Section. 4. Depending on the driver being installed, either “LSI PCI High Performance Driver” , or “LSI Logic Ultra3 PCI SCSI Driver” is shown highlighted. Press Enter to proceed. 5. W indows NT should now recognize the miniport driver(s) and the SCSI hardware. Press Enter to continue. At this point, simply follow the Microsoft Windows NT installation procedure. As for the onboard LAN and VGA, please refer to the later sections for network and graphics driver installation. B2. Boot Floppy Disk Installation 1. Start the W indows NT installation by booting from the Microsoft Setup floppy diskette. 2. Press Enter when the W elcome to Setup screen appears. The W indows NT W orkstation Setup window appears next. 3. Press S to skip automatic detection and perform a manual selection. A screen displays the message “Setup has r ecognized the following mass storage devices in your computer ...” . 4. W ith floppy disk 2, there is an initial setup screen that prompts you to continue by pressing Enter . 5. Press S to skip mass storage device detection. ( If Enter is pressed, the installation program scans for SCSI adapters and finds the LSI PCI ( 53C810 ) driver which is an older version of the SYMC8XX.SYS driver . Let installation continue and change the driver when the installation is completed. ) T o change the driver , see Existing System Installation .
ASUS TR-DLSR User ’ s Manual 75 5. OS Driver Installation 5. Driver Installation WinNT4.0 Server 6. When a screen displays the SCSI adapters found, choose S to configure additional SCSI adapters. 7. Move the highlight bar to Other and press Enter . 8. When prompted for the manufacturer-supplied hardware support disk, insert the appropriate LSI driver diskette containing the W indows NT driver required to support your LSI adapter(s) and press Enter . The driver files are distributed with ASUS Driver Support CD and created from the previous section “Preparing a LSI Driver Diskette” section. 9. Depending on the driver being installed, either “ LSI PCI High Performance Driver” , or LSI Logic Ultra3 PCI SCSI Driver is shown highlighted. Press Enter to proceed. 10. The W indows NT W orkstation Setup window reappears. If using an IDE CD- ROM Drive for installation, press S to load additional drives. Another window appears. Scroll up and select: IDE CD-ROM (A T API 1.2/PCI IDE Controller Press Enter . (-or-) If you have completed configuring additional SCSI adapters, press Enter . 11 . W indows NT should now recognize the miniport driver and the SCSI hardware. Press Enter to continue. At this point, simply follow the Microsoft W indows NT installation procedure. As for onboard LAN and VGA installation, please refer the later sections for network and VGA driver installation. C. Existing System Installation 1. Boot W indows NT system and log on as Administrator . 2. Click on the Start button. Select Settings — >Control Panel . 3. Double click on SCSI Adapters icon. 4. Click the Drivers tab. If the old NCRSDMS.SYS, NCRC810.SYS, NCRC8XX.SYS, or SYMC810.SYS drivers are listed, select the driver(s) and choose Remove before adding the new driver . If the driver name of the driver you are installing SYM_HI.SYS or LSI_U3.SYS is listed, remove it before adding the new driver . Select OK when the Remove Driver message prompts: “Are you sure you want to remove this driver?” Click OK. 5. Click Add . A list of installed adapters will appear . 6. Click the Have Disk button. 7. When prompted, insert the appropriate LSI driver diskette containing the W indows NT driver required to support your LSI adapter(s). The path to copy manufacturer ’ s files is: A:\WINNT\MINIPORT and select OK . 8. Depending on the driver being installed, either LSI PCI High Performance Driver or LSI Logic Ultra3 PCI SCSI Driver is shown highlighted on the Install Driver menu. If it is not highlighted, select it. Choose OK .
76 ASUS TR-DLSR User ’ s Manual 5. OS Driver Installation 5. Driver Installation WinNT4.0 Server 9. For the path to the OEM SCSI Adapter files, A:\WINNT\MINIPORT should be displayed. Select Continue. Then remove the floppy diskette from your A: drive. 10. The System Settings Change message displays: “Y ou must restart your computer before the new settings take ef fect. Do you want to restart your computer now? ” Click on the Ye s button to restart and reboot W indows NT . If you choose Cancel , remember that you must restart before the new driver will load. 11 . Rebooting loads your new miniport driver(s). II. Intel 82559 Network Driver Installation A. Preparing Intel 82559 Lan Driver Diskette If you need to use a floppy disk to install the onboard Intel 82559 network adapter drivers, use the MAKEDISK.BA T utility located in the \LAN\MAKEDISK directory on ASUS Driver Support CD. MAKEDISK [operating system] [destination ] where [operating system] is the OS for which you are creating the diskette, and [destination] is the drive letter and path (such as A:). If no destination is specified, the A: drive will be used. The possible [operating system] options are: NT = Microsoft W indows NT W2K = Microsoft W indows* 2000 NW = Novell NetW are servers and clients Make sure you have a 1.44 MB formatted, non-bootable diskette in the floppy drive when using this utility . Alternately , you can use the MAKENT .BA T files (located in the \LAN root directory on this CD) to simplify this process: MAKENT .BA T — Creates a drivers disk for W indows NT B. New System Installation 1 . Press Next when Installing W indows NT Networking screen appears. 2. Select W ired to the Network: Press Next . Y ou can select install IIS or not. 3. Press Select from list……. . Insert the PRO/100 adapter diskette or ASUS Driver Support CD and click Have Disk . CAUTION : Don ’ t let the W indows NT system to detect the onboard network device. The bundled driver cannot support Intel 82559 network controller and will cause the system installation failure.
ASUS TR-DLSR User ’ s Manual 77 5. OS Driver Installation 5. Driver Installation WinNT4.0 Server 4. T ype D:\LAN (for ASUS Driver Support CD) or A:\ (for floppy) in the dialog box and click OK. Then follow the prompts to complete installation. When the adapter is added you ’ll see a new adapter “Intel(R) PRO Adapter” listed in the Network adapters list. 5. Click Next to finish and configure any protocols as prompted. C. Existing System Installation 1. Double-click the Network icon in the Control Panel . 2 . Select the Adapter tab. 3. Click Add . Y ou ’ ll see a list of adapters. 4. Don ’ t select an adapter from this list. Instead, insert the PRO/100 adapter diskette or ASUS Driver Support CD and click Have Disk . 5. T ype D:\LAN (for CD) or A:\ (for floppy) in the dialog box and click OK. Then follow the prompts to complete installation. When the adapter is added you ’ ll see a new adapter listed in the Network adapters list. 6. Click OK to finish and configure any protocols as prompted. 7. Restart W indows NT when prompted.
78 ASUS TR-DLSR User ’ s Manual 5. OS Driver Installation 5. Driver Installation WinNT4.0 Server III. A TI Rage XL Display Driver Installation 1. Start up W indows NT in VGA mode. 2. Run the W indows NT Display program located in the Control Panel, under Settings in the Start menu or right click the mouse button on the desktop and select Pr operties from the popup menu. 3. Select the Settings tab. 4. Select Display T ype... . 5. Select Change... from the display options. 6. Select Have Disk... 7. W indows NT system will prompt you for the correct path, enter the path of the driver , such as D:\A TI\NT40 (assuming your CD-ROM drive is letter D) 8. A list of video adapters will be displayed. Select the “ XPER T LCD PCI ” , then click on OK button. 9. W indows NT will once again prompt for confirmation. All appropriate files are then copied to the hard disk. Select Apply in Control Panel. 10. The installed driver will become active once you restart W indows NT .
ASUS TR-DLSR User ’ s Manual 79 5. OS Driver Installation 5. Driver Installation Windows 2000 2. Microsoft Windows 2000 Server I. LSI SCSI Driver Installation LSI Logic and Microsoft provide miniport drivers, called SYM_HI.SYS that are bundled with W indows 2000 along with non-bundled drivers LSI_U3.SYS. These miniport drivers complete the path to a LSI controller or processor with an optional SDMS SCSI BIOS. The next sections describe these drivers and their installation. Therefore, user only need to load the driver manually when the CUR-DLS M/B has build-in with LSI SYM53C1010 SCSI controller . As for LSI SYM53C896 SCSI controller , it ’ s always bundled in W indows 2000 system. A. Preparing a LSI Driver Diskette The drivers are located on the ASUS Driver Support CD at: \SDMS\DRIVERS\WIN2K\ XXX2K\I386\WINNT\MINIPOR T where XXX2K represents the specific W indows NT subdirectory . For example, the LSI_U3.SYS driver is located in the Ultra32K subdirectory . Copy all the files starting from the I386 subdirectory through the MINIPOR T subdirectory to the root directory of a clean floppy diskette. Use this LSI driver diskette during installation. (-or -) Use the self-extracting image files for W indows 2000 drivers. For the SYM_HI.SYS driver , the executable file is located here: \SDMS\DISKIMAG\W2K_HI For the LSI_U3.SYS driver , the executable file is located here: \SDMS\DISKIMAG\W2K_U3 B. New System Installation The SYM_HI.SYS drivers are bundled with W indows 2000. These drivers support the SYM53C8XX family of LSI controllers. The LSI_U3.SYS drivers are non- bundled drivers. The LSI_U3.SYS driver supports the SYM53C1010 LSI controller . T o install W indows 2000 on a new system, the system BIOS must support booting from a CD-ROM. LSI BIOS settings may need to be changed to allow CD-ROM booting. 1. Start the W indows 2000 installation by booting from the W indows 2000 CD- ROM.
80 ASUS TR-DLSR User ’ s Manual 5. OS Driver Installation 5. Driver Installation Windows 2000 2. For installation of the LSI_U3.SYS drivers, when the screen displays “ W indows 2000 Setup ” press the F6 key to install the LSI_U3.SYS drivers. This must be done or else these new drivers will not be recognized. If only the SYMC8XX.SYS and/or SYM_HI.SYS drivers are needed no user action is required as they will be loaded from the CD-ROM automatically . Note: If F6 is not pressed, the user is still given the opportunity to load additional drivers later in the installation process. However , any driver loaded at this later time is not recognized and no devices controlled by that driver are available during W indows 2000 Setup. 3. When prompted for the manufacturer -supplied hardware support disk, insert the appropriate LSI driver diskette containing the W indows 2000 driver required to support your LSI adapter(s) and press Enter. The LSI Driver diskette is creating prior to installing W indows 2000. 4. The appropriate driver is shown highlighted. Press Enter to proceed. 5. Return to the W indows 2000 Setup screen. Press Enter to proceed. The message about setup loading files appears. At this point, simply follow the Microsoft W indows 2000 installation procedure. C. Existing System Installation 1. Boot W indows 2000 and log on as Administrator . 2. Right click on My Computer and click on Pr operties . 3. Click on the Hardwar e tab, and then click on the Device Manager button. 4. Click the “ ” to the left of the SCSI and RAID controllers line. Find the adapter desired for the driver upgrade and double click on the entry . Click on the Driver tab. 5 . Information on the currently installed driver is displayed, and additional driver details can be viewed by clicking the Driver Details ….. button. 6. T o update the existing driver , click the Update Driver button. The Upgrade Device Driver W izard begins. Click on the Next button. 7. Make sure Search for a suitable driver for my device is selected, then click on the Next button. 8. Make sure the Floppy disk drives location is checked. Insert the appropriate LSI driver diskette that contains the W indows 2000 driver required to support your LSI adapter(s) and press Enter . The LSI driver diskette was created earlier . 9. The system scans the existing driver database and the floppy diskette drive for drivers for the selected adapter . 10. A list of suitable drivers appears. The entry for the upgrade driver can be verified by scrolling the display to the right, and viewing the Location field. Highlight the driver for the upgrade installation disk and click on the Next button.
ASUS TR-DLSR User ’ s Manual 81 5. OS Driver Installation 5. Driver Installation Windows 2000 11 . In some cases, a message will state that this driver is not digitally signed. This message informs the user that a non-signed driver is being installed. Either click No to cancel the installation if the non-signed driver is not desired or click Ye s to continue the installation. Note: Drivers are digitally signed by the Microsoft W indows Hardware Quality Lab (WHQL). Due to the delay between the general customer release by LSI Logic of W indows drivers and the completion of WHQL testing, some drivers that are distributed with adapters or downloaded from the LSI Logic web site at www .lsilogic.com may not be digitally signed. 12. The system will load the driver from the LSI driver diskette. A message box may appear indicating that the target (existing) driver is newer than the source (upgrade) driver . Click No to cancel the driver upgrade at this point or click Ye s to continue the installation.
82 ASUS TR-DLSR User ’ s Manual 5. OS Driver Installation 5. Driver Installation Windows 2000 II. Intel 82559 Network Driver Installation The W indows 2000 system can recognize onboard Intel LAN chip as “ Intel 8255x- based PCI Ethernet Adapter [10/100] ” . Basically , user doesn ’ t need to load/change any driver for onboard LAN device. However , you can change the bundled network driver on W indows 2000 by following approach. A. Preparing Intel 82559 Lan Driver Diskette If you need to use a floppy disk to install the onboard Intel 82559 network adapter drivers, use the MAKEDISK.BA T utility located in the \LAN\MAKEDISK directory on ASUS Driver Support CD. MAKEDISK [operating system] [destination ] where [operating system] is the OS for which you are creating the diskette, and [destination] is the drive letter and path (such as A:). If no destination is specified, the A: drive will be used. The possible [operating system] options are: NT = Microsoft W indows NT 2K = Microsoft W indows* 2000 NW = Novell NetW are servers and clients Make sure you have a 1.44 MB formatted, non-bootable diskette in the floppy drive when using this utility . Alternately , you can use the MAKEW2K.BA T files (located in the \LAN root directory on this CD) to simplify this process: MAKEW2K.BA T — Creates a drivers disk for W indows 2000 B. Update Driver on an Existing System Installation 1. Boot W indows 2000 system and log on as Administrator . 2. Click on the Start button. Select Settings — >Contr ol Panel . 3. Double-click the System icon in the Contr ol Panel . 4 . Select the Hardwar e tab. Click on Device Manager …. Button. 5. Click the Network Adapters . And highlight “ Intel 8255x-based PCI Ethernet Adapter [10/100] ” . Click right-button on the mouse. Select Pr oper ties . 6 . Select the Driver tab. Click on Update Drivers.. Button.
ASUS TR-DLSR User ’ s Manual 83 5. OS Driver Installation 5. Driver Installation Windows 2000 7. Click Next . Select the “ Display a list of the known drivers for this device” . 8. Click Have Disk … . Select a location for the network driver . User can use floppy diskette or CD-ROM drive (\LAN directory from ASUS Driver Support CD). Click OK . 9. Select “ Intel ® PRO/100 PCI Adapter ” from the listed Network Adapters. Click Next. System would prompt you an Update Driver W arning message. Click Y es to continue Installing driver .
84 ASUS TR-DLSR User ’ s Manual 5. OS Driver Installation 5. Driver Installation Windows 2000 10. Click Next . When it prompted the file “ prosetp.cpl” needed (see below figure). T ype D:\LAN (from ASUS Driver Support CD) or A:\ (User must copy “ prosetp.cpl” file from D:\LAN in advanced) in the dialog box and click OK . 11 . Click Finish . W indows 2000 system will prompt if you want to restart the system now . After system been restarted, the new driver will be loaded into the system. III. A TI Rage XL Display Driver Installation W indows 2000 system can correctly recognize A TI RAGE XL PCI driver during system installation. User need not to load any driver for supporting the onboard A TI RAGE XL graphics chip.
ASUS TR-DLSR User ’ s Manual 85 5. OS Driver Installation 5. Driver Installation Novell Netware 3. Novell NetW are Server I. LSI SCSI Driver Installation A single driver (*HAM) is provided for the Novell NetW are 3.12, 4.XX, and 5.0 environments. This document explains how to install and use the SDMS NWP A SCSI Host Adapter Module (HAM) driver for NetW are. The SDMS NWP A solution consists of the device drivers, SYMHINW .HAM and LSI_U3NW .HAM and the NetW are 4.XX installation files SYMHINW .DDI and LSI_U3NW .DDI. SYMHINW .HAM and LSI_U3NW .HAM are NWP A Host Adapter Modules (HAMs). In order to support SCSI devices, load the HAM in conjunction with a SCSI Custom Device Module (CDM). Novell has developed generic CDMs to support SCSI-2 hard drives, SCSI CD-ROM devices, SCSI Magneto Optical devices, SCSI tape devices, and SCSI changer devices. In addition, third party vendors are developing CDMs to support their specific devices. In the following, the NetW are 5.x, 4.xx and 3.12 installation procedure are listed for the reference. A. Preparing a LSI Driver Diskette The SDMS ™ NWP A drivers for the Novell NetW are operating system are located on the ASUS Driver Support CD at: \SDMS\DRIVERS\NetW are\ Copy all the drivers into a diskette and it will be used for the NetW are system installation. Label it as “ LSI driver for NetW are ” . B. NetW are 5.XX New Installations 1. Begin the file server installation according to the instructions in the file server installation chapter in the Novell NetW are Installation Manual. 2. When the NetW are installation procedure prompts you a Device type screen, press Modify to add a Storage adapters: (Default only IDEA T A available). Press INS for adding a new driver . Please put the LSI driver for NetW are diskette into drive A: Then use the INS key to select an unlisted driver . A dialog box appears. If the driver diskette is in the A: drive, press Enter to continue. The SYMHINW .HAM or LSI_U3NW .HAM drivers appear as a selection.
86 ASUS TR-DLSR User ’ s Manual 5. OS Driver Installation 5. Driver Installation Novell Netware 3. Highlight Disk and CD-ROM Drivers (e.g., IDEA T A). Press Enter and load an additional driver . Then press the INS key . The system always defaults to the A: path. Highlight the HAM driver and press Enter. Select Ye s to save and move the driver into the operating system. Press Enter for the system to copy the files. 4. Load a separate instance of the driver for every LSI controller SCSI channel or host adapter present in the system. 5 . When prompted for a slot number , accept the slot numbers displayed. Make sure to write these slot numbers down for future reference. 6. When asked to edit the ST AR TUP .NCF file, make sure the SYMHINW .HAM or LSI_U3NW .HAM is loaded once for each LSI controller SCSI channel present in the system. Add the statement SLOT=<slot number> to each load line in the ST AR TUP .NCF , by specifying the slot numbers written down in step 5 above, with only one slot number per load instance. The HAM driver(s) are loaded for each LSI controller SCSI channel from the first LOAD statement to the last LOAD statement. C. NetW are 4.XX New Installations 1. Begin the file server installation according to the instructions in the file server installation chapter in the Novell NetW are Installation Manual. 2. When the NetW are installation procedure prompts you for a driver disk, insert the LSI driver for NetW are diskette into drive A: Then use the INS key to select an unlisted driver . A dialog box appears. If the driver diskette is in the A: drive, press Enter to continue. The SYMHINW .HAM or the LSI_U3NW .HAM driver appears as a selection. 3. Highlight Disk and CD-ROM Drivers (e.g., IDEA T A). Press Enter and load an additional driver . Then press the INS key . The system always defaults to the A: path. Highlight the HAM driver and press Enter. Select Ye s to save and move the driver into the operating system. Press Enter for the system to copy the files. 4. Load a separate instance of the driver for every LSI controller SCSI channel or host adapter present in the system. User must load twice for LSI SCSI driver with different slot number from ST ARTUP .NCF file as below . load SYMHINW .HAM (or LSI_U3NW .HAM) Slot=10004 load SYMHINW .HAM (or LSI_U3NW .HAM) Slot=10005 5. When prompted for a slot number , accept the slot numbers displayed. Make sure to write these slot numbers down for future reference. 6. When asked to edit the ST AR TUP .NCF file, make sure the SYMHINW .HAM or LSI_U3NW .HAM is loaded once for each LSI controller SCSI channel present in the system. Add the statement SLOT=<slot number> to each load line in the ST AR TUP .NCF , by specifying the slot numbers written down in step 5 above, with only one slot number per load instance.
ASUS TR-DLSR User ’ s Manual 87 5. OS Driver Installation 5. Driver Installation Novell Netware II. Intel 82559 Network Driver Installation A. Preparing Intel 82559 Lan Driver Diskette If you need to use a floppy disk to install the onboard Intel 82559 network adapter drivers, use the MAKEDISK.BA T utility located in the \LAN\MAKEDISK directory on ASUS Driver Support CD. MAKEDISK [operating system] [destination ] where [operating system] is the OS for which you are creating the diskette, and [destination] is the drive letter and path (such as A:). If no destination is specified, the A: drive will be used. The possible [operating system] options are: NT = Microsoft W indows NT W2K = Microsoft W indows* 2000 NW = Novell NetW are servers and clients Make sure you have a 1.44 MB formatted, non-bootable diskette in the floppy drive when using this utility . Alternately , you can use the MAKENW .BA T files (located in the \LAN root directory on this CD) to simplify this process: MAKENW .BA T — Creates a drivers disk for Novell NetW are servers and clients. B. NetW are 4.XX & 5.X Installations 1. Prepare the Intel PRO/100 NetW are drivers from previous section. 2. Install NetW are 4.xx or 5.x according to the NetW are instructions. 3. When the NetW are installation procedure prompts you for a Network Driver , insert the Intel PRO/100 drivers diskette into drive A: Then use the INS key to select an unlisted driver . A dialog box appears. The “ E100B.LAN — Intel Pro/100 PCI Adapter driver “ driver appear as a selection. CAUTION : If the “ Loader could not find public symbol: <symbol name> ” error message prompted when system is loading Intel Pro/100 PCI network driver , it ’ s because the related network driver modules are too old. User must download the latest Netware Support Pack from Novell web site at: http://support.novell.com/products/nw41 1/patches.htm (For example: the support pack for NetW are 4.1 1).
88 ASUS TR-DLSR User ’ s Manual 5. OS Driver Installation 5. Driver Installation Novell Netware 4. Installation of the Intel 82559 Network Adapter for NetW are 5.x or 4.xx is complete. Add or check the load and bind statements you need to the server ’ s AUTOEXEC.NCF file so the PRO/100 adapter driver loads automatically load and bind the server driver as follows: LOAD C:<P A TH>\E100B SLOT=x FRAME=ETHERNET_802.2 BIND IPX T O E100B NET=xxxxxxxx Where: SLOT=x Specifies the NBI (NetW are Bus Interface) slot number . Substitute x with the valid value for the adapter . Y ou will be prompted with the slot number(s) of installed PRO/100 adapters. The NBI numbers are dif ferent from the slot number indicated in the SETUP .EXE utility . NET=xxxxxxxx is the unique network address for that LAN segment. The default frame type is 802.2. If your workstation needs to use the 802.3 frame type, see the section later in this document about using multiple frame types on one adapter . III. A TI Rage XL Display Driver Installation User can select the “ Super VGA ” for the X Server on NetW are 5.x server system. The other NetW are system didn ’t support X Server and user didn ’ t need the VGA driver support.
ASUS TR-DLSR User ’ s Manual 89 5. OS Driver Installation 5. Driver Installation Sun Solaris 4. SUN Solaris X86 Server I. LSI SCSI Driver Installation A. Building the SYMHISL Driver Update Diskette T o create a SYMHISL diskette for Solaris installations, copy the raw symitu.dd image file onto a 1.44 Mbytes floppy diskette. This process is dependent upon the operating system that you are using to create this diskette. See the instructions below for UNIX System and DOS System Users. For UNIX System Users: Follow these steps to create the SYMHISL Driver Update diskette: 1. Insert a 3.5" diskette into the floppy diskette drive. 2. At the UNIX prompt, type: #volcheck -v #dd if=/<path>/symitu.dd of=/vol/dev/aliases/floppy0 bs=36k #eject floppy The <path> is where the dd image is located. On this CD-ROM, the dd image file is located here: /SDMS/DRIVERS/UNIXES/SOLARIS/SOLARIS/SYMITU.DD For DOS System Users: Under this section, DOS system users have two choices. 1. Use a utility that will copy the raw dd image onto a 1.44 Mbytes floppy diskette. This dd image is located at: \SDMS\DRIVERS\UNIXES\SOLARIS\SOLARIS\SYMITU.DD RA WRITE3.COM, which is a public domain utility , is available on this CD- ROM at this location: \SDMS\DRIVERS\UNIXES\RA WRITE3.COM Instructions for using this utility are included in its accompanying RaW rite file or as a Microsoft W ord document located at: \SDMS\DRIVERS\UNIXES\RA WRITE3.DOC 2. The other DOS alternative is to use the self-extracting image file that is located at: \SDMS\DISKIMAG\SOLARIS.EXE B. New System Installation These instructions provide details to install the SDMS symhisl driver using the SYMHISL Update diskette created above during installation of the operating system using the SYM53C896 or SYM53C1010 controller . T o use the driver on the SYMHISL Driver Update diskette to install Solaris X86 (Intel Platform Edition) on a machine, follow the next steps.
90 ASUS TR-DLSR User ’ s Manual 5. OS Driver Installation 5. Driver Installation Sun Solaris 1. Insert the Solaris Device Configuration Assistant Diskette into your machine ’ s diskette drive. Also insert the Solaris Installation CD-ROM; or for network installation, verify with your system administrator that the Solaris Network Installation image is available on your network. 2. T urn on your machine. When the Solaris Device Configuration Assistant screen appears, choose F4_Add Driver . The message “Enumerating buses... ” appears. Then, the Install Driver Update screen appears. 3. Remove the Solaris Device Configuration Assistant Diskette from the diskette drive and insert the first Solaris Driver ITU diskette you want. 4. Press F2_Continue . The Select Solaris System V ersion screen appears. 5. Select the appropriate Solaris operating system, and press F2_Continue . The Loading Driver Update Software screen appears, along with a progress bar that shows the percentage of drivers that have been extracted from the diskette. Drivers are read into memory and survive long enough for the system to successfully boot to its installation program. When all the new drivers on the diskette have been processed, the Continue Driver Update Installation screen appears. 6. Remove the Solaris Driver ITU diskette from the diskette drive and insert the next Solaris Driver ITU diskette you want, if any . 7. Press F2_Continue . The Loading Driver Update Software screen appears, along with a progress bar that shows the percentage of drivers that have been extracted from the diskette. 8. Repeat Step 4 through Step 8 until all the Solaris Driver ITU diskettes you want are installed. 9. When all the drivers are processed, remove the Solaris Driver ITU diskette from the diskette drive and reinsert the Solaris Device Configuration Assistant Diskette. Important: Do not remove the Solaris Device Configuration Assistant Diskette from the diskette drive until you see the following message displayed in a dialog box: “If you want to bypass the device configuration and boot screens when the system reboots, eject the Device Configuration Assistant/Boot diskette now . ” 10. Press F2_Continue . The Solaris Device Configuration Assistant screen appears. 11 . Press F2_Continue. The “Enumerating buses ” message appears. The Scanning Devices screen is then displayed. System devices are scanned. When scanning is complete, the Identified Devices screen appears. 12. Press F2_Continue . The message “ Loading driver ... ” appears followed by messages about the drivers that are required to boot your system. After a few seconds, the Boot Solaris screen appears.
ASUS TR-DLSR User ’ s Manual 91 5. OS Driver Installation 5. Driver Installation Sun Solaris 13. At the Boot Solaris screen, select the device controller attached to the device that contains your install medium, i.e., CD-ROM or Network device. 14. Press F2_Continue . Drivers for the device controller that you selected are displayed. Y our system boots to run the install program. The install program starts and your machine begins booting the complete Solaris operating environment. The following messages appears some time later , and prompts the user to insert each of the Solaris Driver ITU diskette(s) required to install into your machine: Installing unbundled device driver support Extracting driver list from tree... <ITU diskette name> driver -name... Please insert the Driver Update diskette labeled <ITU diskette name>. Press <ENTER> when ready . 15. Remove the Solaris Device Configuration Assistant Diskette. Reinsert the SYMHISL Driver ITU diskette that you inserted earlier into the diskette drive. 16. Press Enter . Packages and/or patches that contain the new drivers are installed from the diskette onto your machine. Messages about each installation appear accordingly . When the following prompt appears: Please insert the Driver Update diskette labelled <SYMHISL>. Press <ENTER> when ready . 17. Insert the SYMHISL ITU diskette into the floppy diskette drive. When the prompt asking if you wish to create a new instance of the SYMHISL package appears, respond with N for no. When the prompt asking if you wish to overwrite the existing instance of SYMHISL appears, respond with Y for yes. 18. If drivers on other Solaris Driver ITU diskettes are required, remove the Driver ITU diskette from the diskette drive, insert the next Driver ITU diskette when prompted to insert it, press Enter, and repeat this process until all drivers you need are installed. 19. Press Enter . When the installation has completed, the message “ Installation complete ” appears. 20. Remove the diskette from the floppy diskette drive. Reboot your machine. When the Solaris operating environment is finished booting and running, the new devices whose drivers you installed are available for use.
92 ASUS TR-DLSR User ’ s Manual 5. OS Driver Installation 5. Driver Installation Sun Solaris C. Existing System Installation Before adding new or updated drivers, the newly supported hardware devices should be installed and configured according to the instructions in the corresponding Device Reference Page, if any . See the Device Reference Manual for Solaris (Intel Platform Edition). When the Solaris Intel Platform Edition software is already installed, the simplest way to add new or updated drivers is to install the Driver ITU diskettes as patches on your system. For more information about managing diskettes and drives, see the System Administration Guide. 1. T o add new or updated drivers, go to the root (\) directory . 2. T o see if the V olume Management software is running on the machine that you are updating, type at the command prompt: # ps -ef | grep vold 3. T o temporarily stop V olume Management if it is running, type this command at the system prompt: # /etc/init.d/volmgt stop 4. Insert the Solaris Driver ITU diskette into the diskette drive. 5. Mount the Solaris Driver ITU diskette at the /mnt mount point: # mount -F pcfs /dev/diskette /mnt Note: Y ou must mount the Solaris Driver ITU diskette at this point in the file structure to update your system successfully . 6. Execute the install script on the diskette: # /mnt/DU/sol_27/i86pc/T ools/install.sh -i The install.sh script searches for all new or updated drivers on the diskette. When a new or updated driver is found, this prompt appears: Unconditionally installing ITUs <ITU driver names> Install patch driver -name [y] 7. If the driver is the one that you want to install, type Y for yes or press Enter . If the driver is not the one you want to install, type N for no. If you specify yes, the install.sh script installs the driver you indicated as well as bootmod and bootbin patches. 8. When the installation has completed, and the install.sh script exits, unmount the diskette by typing at the command prompt: # cd / # unmount /mnt 9. Remove the Solaris Driver ITU diskette from the diskette drive. 10. Reboot your machine by typing at the command prompt: # touch /reconfigure # reboot
ASUS TR-DLSR User ’ s Manual 93 5. OS Driver Installation 5. Driver Installation Sun Solaris 11 . If you have not already done so, turn off your system, add the new hardware, and turn on your system again. 12. At the << Current Boot Parameters >> prompt, type: b -r to force reconfiguration of the machine. When the Solaris operating environment is finished booting and running, the new devices whose drivers you installed are available for use. II. Intel 82559 Network Driver Installation Solaris7 system can correctly recognize Intel 82559 controller by itself at installation step. User didn ’t need to load the network driver for the onboard LAN device. III. A TI Rage XL Display Driver Installation Solaris 7 cannot support A TI Rage XL graphic default, user can configure the graphic as a “ Standard VGA ” device for supporting Solaris X W indow .
94 ASUS TR-DLSR User ’ s Manual 5. OS Driver Installation 5. Driver Installation SCO Open Server 5. SCO Open Server 5.0.x I. LSI SCSI Driver Installation A. Building the SCO OpenServer BTLD Diskette T o create a BTLD diskette for SCO OpenServer system, copy the raw dd image file onto a 1.44 Mbytes floppy diskette. This process is dependent upon the operating system that you are using to create this diskette. See the instructions below for UNIX System and DOS System Users. For UNIX System Users: Follow these steps to create the BTLD diskette: 1. Insert a 3.5" diskette into the floppy diskette drive. 2. At the UNIX prompt, type: [dd if=/<path>/sco.dd of=/dev/fd0135ds18]. The <path> is where the dd image is located. On this CD-ROM, the dd image file is located here: /SDMS/DRIVERS/UNIXES/OPNSER VR/SCO.DD For DOS System Users: Under this section, DOS system users have two choices. 1. Use a utility that will copy the raw dd image onto a 1.44 Mbytes floppy diskette. This dd image is located at: \SDMS\DRIVERS\UNIXES\OPNSER VR\SCO.DD RA WRITE3.COM, which is a public domain utility , is available on this CD- ROM at this location: \SDMS\DRIVERS\UNIXES\RA WRITE3.COM Instructions for using this utility are included in its accompanying RaW rite file or as a Microsoft W ord document located at: \SDMS\DRIVERS\UNIXES\RA WRITE3.DOC 2. The other DOS alternative is to use the self-extracting image file that is located at: \SDMS\DISKIMAG\OPNSERVR.EXE
ASUS TR-DLSR User ’ s Manual 95 5. OS Driver Installation 5. Driver Installation SCO Open Server B. New System Installation This procedure installs SCO UNIX onto a hard disk drive. This installation is necessary to build a new UNIX kernel that includes your SDMS driver . During installation, you are given the option of retaining current partitions on the root hard disk. For instance, you could have a DOS partition or a user UNIX partition already established on the drive. For more details on UNIX installation, refer to the SCO OpenServer Handbook. 1. Link the SDMS BTLD into the UNIX kernel during installation. 2. Insert the SCO UNIX installation diskette and reboot the system. For SCO OpenServer 5, this diskette is labeled Boot Disk. 3. At the boot prompt, type: [Boot : link] Press Enter . 4. At the next prompt, type: [slha] Do not remove the boot diskette. Press Enter . 5. When prompted during the installation, insert either the proper installation diskette or the SDMS BTLD diskette, and press Enter . The system may prompt you to enter a routine number: “ Please enter which r outine (0-40) to r eplace ‘ ?’ to list, ‘ a’ to add “ slhainit” at the end [default], ‘ n’ to do nothing, or ‘ q’ to quit ” Enter the indicated routine number that precedes this message. Then the system may prompt with another inquiry: “ Please enter which r outine (0-2) to r eplace ‘ ?’ to list, ‘ a ’ to add “ slhapoll” at the end [default], ‘ n’ to do nothing, or ‘ q’ to quit” Enter the indicated routine number that precedes this message. 6. Continue the installation according to the SCO UNIX documentation. C. Existing System Installation This procedure assumes SCO UNIX is already installed on a hard disk drive. This installation is necessary to build a new UNIX kernel that includes the proper LSI host adapter driver . The basic steps for accomplishing this are outlined below . For more details on UNIX installation, refer to the SCO UNIX System Administrator ’ s Reference Manual. 1. The SCO OpenServer 5 system automatically creates a file unix.safe during installation. T o access this UNIX kernel, type after the boot prompt: [ Boot : unix.safe] Press Enter . 2. Log on as system administrator “ r oot ”. 3. Insert the SDMS BTLD diskette in the floppy drive and type: [# installpkg] Press Enter to continue.
96 ASUS TR-DLSR User ’ s Manual 5. OS Driver Installation 5. Driver Installation SCO Open Server 4. A prompt appears to insert the requested diskette. Since the BTLD diskette is already inserted, press Enter . 5. A prompt asks for the name of the package. T ype: [slha] Press Enter to continue. 6. If a driver is already present from a previous installation, a prompt inquires about replacing it. Reply y for yes. 7. Once the install package (installpkg) has completed, relink the kernel by typing: [# /etc/conf/cf.d/link_unix] 8. The system will execute the command and then will prompt for a series of responses: a. “ Do you want this kernel to boot by default (y/n)?” T ype: [y] Press Enter . The system backs up the old kernel. b. “ Do you want the kernel envir onment r ebuilt (y/n)? ” T ype: [y] Press Enter . 9. T o activate the new kernel, you must reboot the system. At the command prompt, type: [# reboot] (or init 6) II. Intel 82559 Network Driver Installation Since the Intel 82559 network driver is non-bundled driver for SCO OpenServer 5.0.x, user must download the Prob100 Network Driver from SCO FTP site at: ftp://ftp.sco.com/pub/drivers/OSR505/network/. Or user can find the Intel 82559 Network driver from ASUS Driver Support CD at: \LAN\UNIX\SCO5\ T o install these drivers, take the following steps: 1. Log on as root. 2. Download and copy the Intel 82559 volume image “ VOL.000.000 ” from SCO web site (or copy from Driver Support CD) to a directory , for example, /tmp/vol . 3. Run ‘custom ’ and select ‘ Install New ’ . Install from your host machine using ‘ Media Images’ . 4. Give the directory name where the volume images have been downloaded, for example, /tmp/vol. 5. Complete the installation and exit custom. 6. Run ‘ netconfig’ and configure the onboard Intel 82559 network adapter: “ Intel ® PRO/100B/PRO /100 PCI Adapter ” 7. T o activate the new kernel, you must reboot the system. At the command prompt, type: [# reboot] (or init 6) III. A TI Rage XL Display Driver Installation Since A TI Rage XL graphic driver is not bundled for SCO OpenServer 5.0.x, user can configure the graphic as standard “ IBM VGA ”. Or , user can change the graphics driver by using “ mkdev graphics ” instruction from command prompt.
ASUS TR-DLSR User ’ s Manual 97 5. OS Driver Installation 5. Driver Installation SCO UnixW are 6. SCO UnixW are Server I. LSI SCSI Driver Installation A. Building the SCO UnixW are C8XX BTLD Diskette T o create a C8XX BTLD diskette to use with UnixW are 2.1.X or UnixW are 7, copy the raw dd image file onto a 1.44 Mbytes floppy diskette. This process is dependent upon the operating system that you are using to create this diskette. See the instructions below for UNIX System and DOS System Users. After the driver diskette been created, labeled as “ PCI SCSI SCO UnixW are driver ” . For UNIX System Users: Follow these steps to cr eate the BTLD diskette: 1. Insert a 3.5" diskette into the floppy diskette drive. 2. At the UNIX prompt, type: [dd if=/<path>/unixware.dd of=/dev/rfd0]. The <path> is where the dd image is located. For UnixW are 2.1.X, the dd image file is located here: /SDMS/DRIVERS/UNIXES/UNIXW ARE/UW21X/UNIXW ARE.DD For UnixW are 7, the dd image file is located here: /SDMS/DRIVERS/UNIXES/UNIXW ARE/UW7/UNIXW ARE.DD For DOS System Users: Under this section, DOS system users have two choices. 1. Use a utility that will copy the raw dd image onto a 1.44 Mbytes floppy diskette. For UnixW are 2.1.X, this dd image is located at: \SDMS\DRIVERS\UNIXES\UNIXW ARE\UW21X\UNIXW ARE.DD For UnixW ar e 7, this dd image is located at: \SDMS\DRIVERS\UNIXES\UNIXW ARE\UW7\UNIXW ARE.DD RA WRITE3.COM, which is a public domain utility , is available on this CD- ROM at this location: \SDMS\DRIVERS\UNIXES\RA WRITE3.COM Instructions for using this utility are included in its accompanying RaW rite file or as a Microsoft W ord document located at: \SDMS\DRIVERS\UNIXES\RA WRITE3.DOC 2. The other DOS alternative is to use the self-extracting image file appropriate for your version of UnixW are. These are located under: \SDMS\DISKIMAG\UW21X.EXE ( -or -) \SDMS\DISKIMAG\UW7.EXE
98 ASUS TR-DLSR User ’ s Manual 5. OS Driver Installation 5. Driver Installation SCO UnixW are B. New System Installation 1. Boot the computer using the installation diskettes that you received with the UnixW are operating system distribution package. UnixW are 7 has two diskettes. 2. Follow the instructions on the screen. 3. Insert the “ PCI SCSI SCO UnixW are driver ” diskette when prompted to insert the host adapter diskette. T o install other host adapter drivers, insert the host adapter diskette provided with the UnixW are distribution package and press Enter . If there are no other host adapter drivers to install, continue the installation and follow the instructions. 4. The system loads the required drivers, such as C8XX , and indicates when they are loaded. 5. At the end of the installation, you will see a prompt to reinsert the HBA driver diskette. Insert the “ PCI SCSI SCO UnixW are driver ” diskette and press Enter . The kernel will be built and the installation will terminate. 6. Remove the driver diskette when prompted to do so and reboot the system. C. Existing System Installation Adding or Updating the C8XX Package for LSI SCSI controller . Before you install the C8XX driver , make a backup copy of the existing kernel: 1. Log on as root . 2. At the shell prompt, type: [# cp /stand/unix /stand/unix.safe] Use this copy of the old kernel to reboot the system if the driver installation fails. Refer to T roubleshooting for more information. 3. Once the old kernel is saved, insert the “ PCI SCSI SCO UnixW are driver ” diskette. 4. Load the driver using the pkgadd command by typing: [# pkgadd -d diskette1] 5. Select C8XX and press Enter . The C8XX driver is then loaded onto the system. 6. The system will again prompt you to load a driver even if loading was successful. T ype q (quit) and press Enter. 7. V erify that the driver is now loaded successfully by typing: [ # pkginfo c8xx] 8. The package information should look like this: “ system c8xx LSI IHV HBA ” 9. After the C8XX package is loaded, a message indicating a system reboot is necessary may appear . T o reboot the system, type the following command: [# init 6] During the boot process, the driver scans the SCSI bus and lists the devices found on it. If the kernel panics during boot, then reboot the system with the saved copy of the old kernel. Booting from the saved copy of the kernel is described in the following section titled “ T roubleshooting. ” If the reboot is successful, the system is ready to use.
ASUS TR-DLSR User ’ s Manual 99 5. OS Driver Installation 5. Driver Installation SCO UnixW are II. Intel 82559 Network Driver Installation Since SCO UnixW are system cannot support Intel 82559 default, user can download the Prob 100 Network Driver from SCO FTP site at: ftp://ftp.sco.com/pub/drivers/ UW710/network/ Or user can find the Intel 82559 Network driver from ASUS Driver Support CD at: \LAN\UNIX\UWx\ It is not necessary , nor recommended, to remove previous versions of this package from the system before installing this updated version. T o install this package, you may use the scoadmin Application Installer from the desktop, or as a root login with pkgadd command. 1. From the UnixW are 7.1.1 OS Updates CD-ROM (Disk 2): # pkgadd -d cdrom1 nd 2. Or , from a download file image or copied from support CD. Copy the driver to a temporary directory , for example /usr/tmp/nd_71 1.pkg. # pkgadd -d /usr/ tmp/nd_71 1.pkg NOTE: Do not use /tmp as the download directory . It could fail with a ‘ No space ’ message during pkgadd . The warnings: W ARNING: UnixW are Update 7.x.x should be reapplied can be safely ignored. There are no files in the Updates that patch this package. 3. After the nd package is loaded, a message indicating a system reboot is necessary may appear . T o reboot the system, type the following command: # init 6 III. A TI Rage XL Display Driver Installation Since SCO UnixW are 7 cannot support A TI Rage XL graphic default, user must configure the graphic as standard “ IBM VGA ” . User can change the graphics driver by using scoadmin instruction from command prompt.
100 ASUS TR-DLSR User ’ s Manual 5. OS Driver Installation 5. Driver Installation RedHat Linux 7. Linux RedHat 6.x and 7.x I. LSI SCSI Driver Installation The LSI SYM53C896 SCSI drivers are bundled under Linux RedHat 6.x and 7.x systems. User can easily follow the Linux RedHat 6.x and 7.x installation procedure to finish the system installation. However , for the SYM53C1010 controller , user must rebuild a new OS kernel (Redhat 6.x) or load the LSI driver (Redhat 7.x) to support the SYM53C1010 controller . For the kernel rebuilding procedure to support Redhat 6.x, check the README file from the ASUS support CD in the following path: \SDMS\DRIVERS\UNIXES\LINUX\README T o support Redhat 7.0, download the LSI 1010 driver REDHA T70.EXE from the ASUS website www .asus.com.tw/pr oducts/addon/scsi/scsilan_drv .html . After downloading the file, extract the driver into a floppy disk. In the Redhat 7.0 installation wizard screen, use the “ Linux dd ” command to install Redhat Linux 7.0 . II. Intel 82559 Network Driver Installation Linux RedHat 6.x and 7.x systems can automatically recognize the Intel 82559 controller during installation. User doesn ’t need to load or modify the network driver for the onboard LAN device. III. A TI Rage XL Display Driver Installation Select “ A TI Xpert XL” in installation stage to support X W indow on Linux RedHat 6.x. User can also change the graphics driver later by executing the “ setup” instruction under the command prompt. The Redhat 7.x can automarically detect the onboard graphics.