Craftsman 11145 Owner's Manual
OWNERS MANUAL MODEL NO. 315.111450 CAUTION: Read Rules for Safe Operation and instructions Carefully SAVE THIS MANUAL FOR FUTLIRE REFERENCE 3/8 INCH CORDLESS DRILL SINGLE-SPEED- REVERSIBLE Introduction Operation Designed exc_usive}y for arid sold only by SEARS, ROEBUCK AND CO, Dept 698/73tA, Sears Tower. Chicago. IL 60684 _QXj9
FULL ONE YEAR WARRANTY ON CRAFTSMAN CORDLESS DRILL If this Craftsman Cordless Drill falls to give complete satisfaction within one year from the date of put.- chase, RETURN IT TO THE NEAREST SEARS STORE THROUGHOUT THE UNITED STATES and Sears wilt replace it, free of charge. If this cordless drill is used for commercial or rentat purposes this warranty applies for only 90 days from the date of purchase. This warranty gives you specific lega! rights, and you may also have other rights which vary from state to state SEARS, ROEBUCK AND CO DEPT. 698/731A SEARS TOWER CHICAGO, IL 60684 IMPORTANI' SAFETY RULES FOR POWER TOOLS READ 1 2. ALL INSTRUCTIONS KNOW YOUR POWER TOOL -- Read owner's manual carefully Learn its applica- tions and limitations as well as the specific potential hazards related to this toot, GUARD AGAINST ELECTRICAL SHOCK BY PREVENTING BODY CONTACT WITH GROUNDED SURFACES. For example: Pipes, radiators, ranges, refrigerator enclosures. 3_ KEEP WORK AREA CLEAN, Cluttered areas and benches invite accidents 4_ AVOID DANGEROUS ENVIRONMENT. Don't use power tool in damp or wet foca- lions or expose to rain. Keep work area well liL 5. KEEP CHILDREN AWAY° All visitors should wear safety glasses and be kept a safe distance from work area. Do not let visitors contact tool or extension cord 6 STORE IDLE TOOLS. When not ir_ use, tools should be stored in a dry, high or locked-up place -- out of the reach of children. 7_ DON'T FORCE TOOL° It wilt do the job better and safer at the rate for which it was designed 8 USE RIGHT TOOL Don't force small tool or attachment to do the job of a heavy duty tool Don't use tool for purpose not intended w for example -- Don't use a circular saw for cutting tree limbs or logs 9 WEAR PROPER APPAREL° No loose clothing or jewelry to get caught in moving parts Rubber gloves and nomskid footwear are recommended when working out.- doors. Also, wear protective hair coverir_g to contain long hair. 10. USE SAFETY GLASSES with all tools, Also face or dust mask if operation is dusty, tl. SECURE WORK. Use clamps or a vise to hold work it's safer than using your hand and it frees both hands to operate tool_ 12 DON'T OVERREACH. Keep proper footing and balance at all times. Do not use where support is unstable 13 MAINTAIN TOOLS WITH CARE. Keep tools sharp at all times, and clean for best and safest performance. Follow instructions for lubricating and changing accessories. Page 2
RULES FOR SAFE OPERATION (CONTINUED) !4,. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see thdt keys and adjusting wrenches are removed from tool before turning it on, 15. NEVER USE IN AN EXPLOSIVE ATMOSPHERE_ Normat sparking of the motor could ignite flammable liquids, gases or fumes, t6 KEEP HANDLES DRY, CLEAN, AND FREE FROM OIL AND GREASE. Always use a clean cloth when cleaning.. Never use brake fluids, gasoline, petroleum_based products, or any strong solvents to clean your tool, 17. STAY ALERT. Watch what you are doing and use common sense, Do not operate tool when you are tired. Do not rush° t8. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center, 19, DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF, Have defective switches replaced by authorized service center° 20, DRUGS, ALCOHOL, MEDICATION. Do not operate _ooI while under the influence of drugs, alcohol, or any medication_ 21. CUTTING, DRILLING, OR DRIVING SCREWS INTO ELECTRICAL WIRING IN WALLS, CEILINGS, OR OTHER AREAS CAN CAUSE BLADE, BIT, OR CHUCK TO BECOME ELECTRICALLY LIVED Grasp only the insulated handle(s) or plastic housing when using the tool 22 WEAR HEARING PROTECTION DURING EXTENDED PERIODS OF OPERATION° IMPORTANT SAFETY RULES FOR BATTERY TOOLS 23 Battery tools do not have to be plugged into an electrical outlet, therefore they are always in operating condition., Be aware of possible hazards when not using your battery tool or when changing accessories° 24. USE ONLY THE CHARGER PROVIDED WITH YOUR BATTERY TOOL. Do not substitute any other charger. Use of another charger could cause batteries to ex- plode causing possible serious injury. 25 DO NOT PLACE BATTERY TOOLS OR THEIR BATTERIES NEAR FIRE OR HEAT. They may explode° 26 DO NOT CHARGE BATTERY TOOL IN A DAMP OR WET LOCATION° 27. Your battery tool shoutd be charged in a location where the temperature is more than 50°F but less than 100"F. 28 Under extreme usage or temperature conditions, battery leakage may occur, if liquid comes in contact with your skin, wash immediately with soap and water, then neutralize with lemon juice or vinegar. If liquid gets in your eyes, flush them with clean water for at _east 10 minutes, then seek immediate medical attention. 29, If carrying your battery tool at your side, make sure it is not running and your finger is not on the switch, Avoid accidental starting. 30 SECURE WORK before applying power. NEVER hold workpiece in your hand or across your legs. 31, SAVE THESE INSTRUCTIONS. Refer to them frequently and use them to instruct third party user° If you loan someone this tool, loan them these instructions also_ Page 3
IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER 1. SAVE THESE INSTRUCTIONS° This manual contains important safety and operating instructions for battery charger Part Number 999555-007. 2. Before using battery charger, read atl instructions and cautionary markings in this manual, on battery charger, and product using battery charger. 3. __To reduce risk of injury, charge only nickel-cadmium type rechargeable batteries. Other types of batteries may burst causing personal injury and damage, 4o Do not e_,pose charger to rain or snow. 5. Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric shock, or injury to persons. 6. To reduce risk of damage to charger body and cord, pul! by charger body rather than cord when disconnecting charger. _ 7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress_ 8 An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock_ tf extension cord must be used, make sure: a. That pins on plug of extension cord are the same number, size and shape as those of plug on charger. b. That extension cord is properly wired and in good electrical condition; and c. That wire size is large enough for AC ampere rating of charger as specified below: i ....... ,,,,,i ..... i,,_ AWG Size 0fC0rd/Length0!i.O0rd,, Feet ........ ii i.... " i iF;e, ........ I AWG 18 t8 18 16 9. DO NOT OPERATE CHARGER WITH A DAMAGED CORD OR PLUG. If damaged, have replaced immediately by a qualified serviceman.. 10. Do not operate charger if it has received a sharp blow, been dropped, or otherwise "- damaged in any way; take it to a qualified serviceman 11 Do not disassemble charger; take it to a qualified serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire_ 12. To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. Turning off controls will not reduce this risk_ 13. Do not use charger outdoors. 14_ Disconnect charger from power supply when not in use. i, '_ ,Jl The operation of any Power Tool can result in iorelgt_ objects being thrown into I i' i_ I_ your eyes, which can result in severe eye damage. Before commencing power toot ! I face shield when needed, We recommend Wide Vision Safety Mask for use over J !! spectacles or standard safety glasses with side shields, available at Sears Catalog | JD Order or Retail Stores. I Page 4
OPERATION KNOW YOUR DRILL See Figure 1_ Before attempting to use your drill, familiarize yourself with el! operating features and safety re- quirements, If any pads are missing do not operate your drill untie the missing parts are replaced. CHARGING YOUR DRILL Your drill has been shipped in a low charge condition to prevent possible problems. Therefore, you should charge tt at least 5 hours prior to use NOTE:Your drill wltl not reach fult charge the first ttme it is charged. Allow several cycles (drilling followed by recharging) for your drill to become fully charged, DRILL SELECTOR TO CHARGE 1, Connect charger to your drill by inserting charger plug Into input jack, NOTE: As shown In Figure 1, input Jack is located at the rear of toot 2 Charger can be used with normal house voltage of 110.120 volts, 60 Hz. AC only. 3, Connect charger Io power supply NOTE: The LED indicator, which is located above the switch, will iight up when charger is properly con. nected to power supply Thts light indicates your drill is charging and will rematn on until charger ts disconnected from power supply. NOTE: Do not operate your drill while it is connected to the charger. The driving ability of your drill will not increase, NOTE: After normal usage, your drtlI usually requires 3 hours of charging time to be fully charged YOUR DRILL _ONTAINS SPECIAL HIGH TEMPERATURE BATTERIES TO HELP PRE- VENT BATTERY DAMAGE WHEN LEFT ON CHARGE FOR EXTENDED PERIODS OF TIME, HOWEVER, ONCE THE BATTERIES OF YOUR DRILL BECOME FULLY CHARGED, WE RECOMMEND THAT YOU UNPLUG YOUR CHARGER FROM POWER SUPPLY THEN DISCONNECT THE CHARGER FROM YOUR DRILL.. UT JACK CHARGER PLUG LED INDICATOi_i// BATTERY CHARGER l SWITCH TRIGGER WRIST STRAP Page 5
BATTERIES OPERATION Your ddtl is equipped with 5 nickel-cadmium rechargeabte batteries Length of service from each charging will depend on the type of work you are do- ing '[he nickel,.cadmium batteries in this tool have been designed to last for the life of the unit under normal operating conditions. Therefore, do not disassemble your drill and attempt to replace them, Handling of these batteries, especially when wearing rings and jewelry, could result in a serious burn WRIST STRAP A wrist strap ts provided to reduce the chances of dropping your drill, Place one hand through wdst strap when carrying your dr_il See Figure 4. SWITCH The switch on your drill is designed for single speed drilling For normal drilling operatfon, depress the switch trigger atl the way. REVERSIBLE Your dri!l has the feature of being reversible The direction of rotation is controlled by a selector located above the switch trigger. See Figure 2. With your drill he{d in normal operating position, the direction of rotor{on selector should be positioned to the left of the switch for drilling The drill direction Is reversed when the selector is to the right of the switch When the selector is in center position, the switch trigger Is locked,, TO PREVENT GEAR DAMAGE, ALWAYS ALLOW THE CHUCK ON YOUR DRILL TO COME TO A COMPLETE STOP BEFORE CHANGING THE DIRECTION OF ROTATION. To stop your drill release switch trigger and allow your drill to come to a complete stop. NOTE: To lock switch trigger, place the direction of rotation selector in center position. See Figure 2 CHUCK KEY A chuck key has been packed with your drill for use when installing or removing bits tt is also used when removing the chuck See Figure 3 CHUCK KEY STORAGE When not in use the chuck key can be placed in the storage area located on the back of your ddt! See Figure 3 Page 6 (Cont.) REVERSE SELECTC SWITCH TRIGG ER CHUCK KEY FORWARD POSITION (LOCK,OFF) Fig, 2 CHUCK KEY STORAGE Fig 3
OPERATION INSTALLING BITS ---- .... 1 Lock switch trigger on your ddtt by placing the direction of rotation selector in center position. 2 Close chuck jaws to a point where the opening is slightly larger than the bit size you intend to use, 3 insert your drilJ bit into chuck the full length of the jaws as shown in Figure 4, BIT 4" Remove chuck key from chuck key storage See Figure 3 5 Tighten chuck jaws by placing chuck key tn each o! the three holes, and tighten in a clockwise direction. DO NOT USE A WRENCH TO TIGHTEN OR LOOSEN THE CHUCK, 6. Remove the chuck key and return to chuck key storage REMOVING BITS t. Lock switch trigger on your dri]! by placing the direction of rotation selector In center position 2 Remove chuck key from chuck key storage, See Figure 3 3 Loosen chuck jaws using the chuck key, DO NOT USE A WRENCH TO TIGHTEN OR LOOSEN THE CHUCK,, 4. Remove drill bit from chuck jaws., 5 Remove chuck key and return to chuck key storage, CHUCK REMOVAL The chuck must be removed in order to use some accessories To remove: 1 LOck switch trigger on your drill by placing the direction of rotation selector in center position 2 Remove chuck key from chuck key storage See Figure 3 3. Close the chuck jaws. Insert chuck key into chuck and tap sharply with a mallet in a clockwise direc- tion as shown in Figure 5 4, Open the chuck jaws and remove the chuck screw by turning it in a clockwise direction See Figure 6 NOTE: The chuck screw has left hand threads 5. Inserl the chuck key in chuck and tap sharply in a counterclockwise direction to loosen it on spin. die, I1 can now be unscrewed by hand, See Figure 7, 6 Return chuck key to chuck key storage, The chuck may become loose on spindle and develop a wobble. Also, the chuck screw may become loose causing the chuck jaws to bind This will prevent them from closing To tighten, follow these steps: 1, Lock swflch trigger on your drill by placing the direction of rotation selector in center position 2 Open the chuck jaws 3 Insert chuck key in chuck and tap with a mallet in a clockwise direction 4. Tighten the chuck screw NOTE; "The chuck screw has left hand threads Page 7 (Cont.) CHUCK KEY HOLE WRIST STRAP .t Fig 4 Ftg 5 Fig 6
DRILLING OPERATION (Cont.) The material to be drilled should be secured in a vise or with ciamps to keep it from turning as the drill bit rotates Hold your drill lirmly and place the bit at the point te be drilled, Depress the switch trigger to start your drill Move the drill bit into the workpiece applying only enough pressure to keep the bit cutting Do not force your drill or apply side pressure to elongate a hoie Let your drill and bit do the work See Fig 8 When drHting metals use a light oil on the drill btt to keep it from overheating, The oil will prolong the lile of the bit and increase the drilling action tf the bit jams in workpiece or tf the dtiH stalis, re_ease switch trigger immediately. Remove the bit from the workpiece and determine the reason for jamming Page 8
MAINTENANCE GENERAL Avoid using solvents when cleaning plastic parts Most plastics are susceptible to various types of oommeP cial solvents and may be damaged by their use, Use clean cloths to remove dirt, dust, oil, grease, etc, ACCESSORIES ...... THE FOLLOWING RECOMMENDED ACCESSORIES ARE CURRENT AND WERE ............. AVAILABLE AT THE TIME THIS MANUAL WAS PRINTED, 5,,Pc, Power Screwdriver Bit Set Cat, No 9 25602 No, 2 Phillips/8.,10 Slotted. 2 Ea Cat No 9 25603 No, 3 PhiUips/6-8 Stotted, 2 Ea Cat, No 9_ 25604 7,Pc Screwdriver Bit Set and Case Cat, No 9. 2555 Doweling Jig Cat No _9 4186 t3,Pc, Power Screwdriver/Nutdriver Set and Case Cat No,, 9 25653 30-Pc Power Screwdriver/Nutdriver Set and Case Cat No. 9 25654 7,Pc Power Nutdriver Bit Set Cat No 9_9 25655 t7,Pc Power Screwdriver/Nutdriver Set and Case Cat No.. 9 25657 High Speed Bits (For Wood or Metal) . ,. 3/8" Max,, Hole Square Cat No, __9 2596 _i'_'_='J_'!,lJJ[=]_The use ot attachments or accessories not listed might be hazardous,. q t REPLACEMENT PARTS WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS Part Number Description 999555_007 Battery Charger _ ,ll ii ii iq , ,Hll Ill " -- '_ ................... Page g
NOTES Page 10
NOTES Page 11
OWNERS MANUAL SERVICE MODEL NO. 315.111450 HOW TO ORDER REPAIR PARTS ............ :: ,L,Im. 1" 3/8 INCH CORDLESS DRILL SINGLE-SPEED REVERSIBLE Now that you have purchased your Drill, shoutd a need ever exist for tepai[ parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co, stores Be sure to provide all perti- nent facts when you call or visit. The model number of your Drill wiil be found on the plate attached to the motor housing. WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION: o PART NUMBER * MODEL NUMBER 315 1 11450 o PART DESCRIPTION ⢠NAME OF ITEM Cordless Drill All parts listed may be ordered from any Sears Ser- vice Center and most Sears stores If the parts you need are not stocked _ocally, your order will be electronically transmitted to a Sears Repair Parts Distribution Center for handling i ...................... -' ........... _ .............. ,,,,u, i i it,i ill i Hqu, p SEARS, ROEBUCK AND CO Dept 698/731A, Sears Tower, Chicago, IL 60684
FULL ONE YEAR WARRANTY ON CRAFTSMAN CORDLESS DRILL If this Craftsman Cordless Drill falls to give complete satisfaction within one year from the date of put.- chase, RETURN IT TO THE NEAREST SEARS STORE THROUGHOUT THE UNITED STATES and Sears wilt replace it, free of charge. If this cordless drill is used for commercial or rentat purposes this warranty applies for only 90 days from the date of purchase. This warranty gives you specific lega! rights, and you may also have other rights which vary from state to state SEARS, ROEBUCK AND CO DEPT. 698/731A SEARS TOWER CHICAGO, IL 60684 IMPORTANI' SAFETY RULES FOR POWER TOOLS READ 1 2. ALL INSTRUCTIONS KNOW YOUR POWER TOOL -- Read owner's manual carefully Learn its applica- tions and limitations as well as the specific potential hazards related to this toot, GUARD AGAINST ELECTRICAL SHOCK BY PREVENTING BODY CONTACT WITH GROUNDED SURFACES. For example: Pipes, radiators, ranges, refrigerator enclosures. 3_ KEEP WORK AREA CLEAN, Cluttered areas and benches invite accidents 4_ AVOID DANGEROUS ENVIRONMENT. Don't use power tool in damp or wet foca- lions or expose to rain. Keep work area well liL 5. KEEP CHILDREN AWAY° All visitors should wear safety glasses and be kept a safe distance from work area. Do not let visitors contact tool or extension cord 6 STORE IDLE TOOLS. When not ir_ use, tools should be stored in a dry, high or locked-up place -- out of the reach of children. 7_ DON'T FORCE TOOL° It wilt do the job better and safer at the rate for which it was designed 8 USE RIGHT TOOL Don't force small tool or attachment to do the job of a heavy duty tool Don't use tool for purpose not intended w for example -- Don't use a circular saw for cutting tree limbs or logs 9 WEAR PROPER APPAREL° No loose clothing or jewelry to get caught in moving parts Rubber gloves and nomskid footwear are recommended when working out.- doors. Also, wear protective hair coverir_g to contain long hair. 10. USE SAFETY GLASSES with all tools, Also face or dust mask if operation is dusty, tl. SECURE WORK. Use clamps or a vise to hold work it's safer than using your hand and it frees both hands to operate tool_ 12 DON'T OVERREACH. Keep proper footing and balance at all times. Do not use where support is unstable 13 MAINTAIN TOOLS WITH CARE. Keep tools sharp at all times, and clean for best and safest performance. Follow instructions for lubricating and changing accessories. Page 2
RULES FOR SAFE OPERATION (CONTINUED) !4,. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see thdt keys and adjusting wrenches are removed from tool before turning it on, 15. NEVER USE IN AN EXPLOSIVE ATMOSPHERE_ Normat sparking of the motor could ignite flammable liquids, gases or fumes, t6 KEEP HANDLES DRY, CLEAN, AND FREE FROM OIL AND GREASE. Always use a clean cloth when cleaning.. Never use brake fluids, gasoline, petroleum_based products, or any strong solvents to clean your tool, 17. STAY ALERT. Watch what you are doing and use common sense, Do not operate tool when you are tired. Do not rush° t8. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center, 19, DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF, Have defective switches replaced by authorized service center° 20, DRUGS, ALCOHOL, MEDICATION. Do not operate _ooI while under the influence of drugs, alcohol, or any medication_ 21. CUTTING, DRILLING, OR DRIVING SCREWS INTO ELECTRICAL WIRING IN WALLS, CEILINGS, OR OTHER AREAS CAN CAUSE BLADE, BIT, OR CHUCK TO BECOME ELECTRICALLY LIVED Grasp only the insulated handle(s) or plastic housing when using the tool 22 WEAR HEARING PROTECTION DURING EXTENDED PERIODS OF OPERATION° IMPORTANT SAFETY RULES FOR BATTERY TOOLS 23 Battery tools do not have to be plugged into an electrical outlet, therefore they are always in operating condition., Be aware of possible hazards when not using your battery tool or when changing accessories° 24. USE ONLY THE CHARGER PROVIDED WITH YOUR BATTERY TOOL. Do not substitute any other charger. Use of another charger could cause batteries to ex- plode causing possible serious injury. 25 DO NOT PLACE BATTERY TOOLS OR THEIR BATTERIES NEAR FIRE OR HEAT. They may explode° 26 DO NOT CHARGE BATTERY TOOL IN A DAMP OR WET LOCATION° 27. Your battery tool shoutd be charged in a location where the temperature is more than 50°F but less than 100"F. 28 Under extreme usage or temperature conditions, battery leakage may occur, if liquid comes in contact with your skin, wash immediately with soap and water, then neutralize with lemon juice or vinegar. If liquid gets in your eyes, flush them with clean water for at _east 10 minutes, then seek immediate medical attention. 29, If carrying your battery tool at your side, make sure it is not running and your finger is not on the switch, Avoid accidental starting. 30 SECURE WORK before applying power. NEVER hold workpiece in your hand or across your legs. 31, SAVE THESE INSTRUCTIONS. Refer to them frequently and use them to instruct third party user° If you loan someone this tool, loan them these instructions also_ Page 3
IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER 1. SAVE THESE INSTRUCTIONS° This manual contains important safety and operating instructions for battery charger Part Number 999555-007. 2. Before using battery charger, read atl instructions and cautionary markings in this manual, on battery charger, and product using battery charger. 3. __To reduce risk of injury, charge only nickel-cadmium type rechargeable batteries. Other types of batteries may burst causing personal injury and damage, 4o Do not e_,pose charger to rain or snow. 5. Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric shock, or injury to persons. 6. To reduce risk of damage to charger body and cord, pul! by charger body rather than cord when disconnecting charger. _ 7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress_ 8 An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock_ tf extension cord must be used, make sure: a. That pins on plug of extension cord are the same number, size and shape as those of plug on charger. b. That extension cord is properly wired and in good electrical condition; and c. That wire size is large enough for AC ampere rating of charger as specified below: i ....... ,,,,,i ..... i,,_ AWG Size 0fC0rd/Length0!i.O0rd,, Feet ........ ii i.... " i iF;e, ........ I AWG 18 t8 18 16 9. DO NOT OPERATE CHARGER WITH A DAMAGED CORD OR PLUG. If damaged, have replaced immediately by a qualified serviceman.. 10. Do not operate charger if it has received a sharp blow, been dropped, or otherwise "- damaged in any way; take it to a qualified serviceman 11 Do not disassemble charger; take it to a qualified serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire_ 12. To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. Turning off controls will not reduce this risk_ 13. Do not use charger outdoors. 14_ Disconnect charger from power supply when not in use. i, '_ ,Jl The operation of any Power Tool can result in iorelgt_ objects being thrown into I i' i_ I_ your eyes, which can result in severe eye damage. Before commencing power toot ! I face shield when needed, We recommend Wide Vision Safety Mask for use over J !! spectacles or standard safety glasses with side shields, available at Sears Catalog | JD Order or Retail Stores. I Page 4
OPERATION KNOW YOUR DRILL See Figure 1_ Before attempting to use your drill, familiarize yourself with el! operating features and safety re- quirements, If any pads are missing do not operate your drill untie the missing parts are replaced. CHARGING YOUR DRILL Your drill has been shipped in a low charge condition to prevent possible problems. Therefore, you should charge tt at least 5 hours prior to use NOTE:Your drill wltl not reach fult charge the first ttme it is charged. Allow several cycles (drilling followed by recharging) for your drill to become fully charged, DRILL SELECTOR TO CHARGE 1, Connect charger to your drill by inserting charger plug Into input jack, NOTE: As shown In Figure 1, input Jack is located at the rear of toot 2 Charger can be used with normal house voltage of 110.120 volts, 60 Hz. AC only. 3, Connect charger Io power supply NOTE: The LED indicator, which is located above the switch, will iight up when charger is properly con. nected to power supply Thts light indicates your drill is charging and will rematn on until charger ts disconnected from power supply. NOTE: Do not operate your drill while it is connected to the charger. The driving ability of your drill will not increase, NOTE: After normal usage, your drtlI usually requires 3 hours of charging time to be fully charged YOUR DRILL _ONTAINS SPECIAL HIGH TEMPERATURE BATTERIES TO HELP PRE- VENT BATTERY DAMAGE WHEN LEFT ON CHARGE FOR EXTENDED PERIODS OF TIME, HOWEVER, ONCE THE BATTERIES OF YOUR DRILL BECOME FULLY CHARGED, WE RECOMMEND THAT YOU UNPLUG YOUR CHARGER FROM POWER SUPPLY THEN DISCONNECT THE CHARGER FROM YOUR DRILL.. UT JACK CHARGER PLUG LED INDICATOi_i// BATTERY CHARGER l SWITCH TRIGGER WRIST STRAP Page 5
BATTERIES OPERATION Your ddtl is equipped with 5 nickel-cadmium rechargeabte batteries Length of service from each charging will depend on the type of work you are do- ing '[he nickel,.cadmium batteries in this tool have been designed to last for the life of the unit under normal operating conditions. Therefore, do not disassemble your drill and attempt to replace them, Handling of these batteries, especially when wearing rings and jewelry, could result in a serious burn WRIST STRAP A wrist strap ts provided to reduce the chances of dropping your drill, Place one hand through wdst strap when carrying your dr_il See Figure 4. SWITCH The switch on your drill is designed for single speed drilling For normal drilling operatfon, depress the switch trigger atl the way. REVERSIBLE Your dri!l has the feature of being reversible The direction of rotation is controlled by a selector located above the switch trigger. See Figure 2. With your drill he{d in normal operating position, the direction of rotor{on selector should be positioned to the left of the switch for drilling The drill direction Is reversed when the selector is to the right of the switch When the selector is in center position, the switch trigger Is locked,, TO PREVENT GEAR DAMAGE, ALWAYS ALLOW THE CHUCK ON YOUR DRILL TO COME TO A COMPLETE STOP BEFORE CHANGING THE DIRECTION OF ROTATION. To stop your drill release switch trigger and allow your drill to come to a complete stop. NOTE: To lock switch trigger, place the direction of rotation selector in center position. See Figure 2 CHUCK KEY A chuck key has been packed with your drill for use when installing or removing bits tt is also used when removing the chuck See Figure 3 CHUCK KEY STORAGE When not in use the chuck key can be placed in the storage area located on the back of your ddt! See Figure 3 Page 6 (Cont.) REVERSE SELECTC SWITCH TRIGG ER CHUCK KEY FORWARD POSITION (LOCK,OFF) Fig, 2 CHUCK KEY STORAGE Fig 3
OPERATION INSTALLING BITS ---- .... 1 Lock switch trigger on your ddtt by placing the direction of rotation selector in center position. 2 Close chuck jaws to a point where the opening is slightly larger than the bit size you intend to use, 3 insert your drilJ bit into chuck the full length of the jaws as shown in Figure 4, BIT 4" Remove chuck key from chuck key storage See Figure 3 5 Tighten chuck jaws by placing chuck key tn each o! the three holes, and tighten in a clockwise direction. DO NOT USE A WRENCH TO TIGHTEN OR LOOSEN THE CHUCK, 6. Remove the chuck key and return to chuck key storage REMOVING BITS t. Lock switch trigger on your dri]! by placing the direction of rotation selector In center position 2 Remove chuck key from chuck key storage, See Figure 3 3 Loosen chuck jaws using the chuck key, DO NOT USE A WRENCH TO TIGHTEN OR LOOSEN THE CHUCK,, 4. Remove drill bit from chuck jaws., 5 Remove chuck key and return to chuck key storage, CHUCK REMOVAL The chuck must be removed in order to use some accessories To remove: 1 LOck switch trigger on your drill by placing the direction of rotation selector in center position 2 Remove chuck key from chuck key storage See Figure 3 3. Close the chuck jaws. Insert chuck key into chuck and tap sharply with a mallet in a clockwise direc- tion as shown in Figure 5 4, Open the chuck jaws and remove the chuck screw by turning it in a clockwise direction See Figure 6 NOTE: The chuck screw has left hand threads 5. Inserl the chuck key in chuck and tap sharply in a counterclockwise direction to loosen it on spin. die, I1 can now be unscrewed by hand, See Figure 7, 6 Return chuck key to chuck key storage, The chuck may become loose on spindle and develop a wobble. Also, the chuck screw may become loose causing the chuck jaws to bind This will prevent them from closing To tighten, follow these steps: 1, Lock swflch trigger on your drill by placing the direction of rotation selector in center position 2 Open the chuck jaws 3 Insert chuck key in chuck and tap with a mallet in a clockwise direction 4. Tighten the chuck screw NOTE; "The chuck screw has left hand threads Page 7 (Cont.) CHUCK KEY HOLE WRIST STRAP .t Fig 4 Ftg 5 Fig 6
DRILLING OPERATION (Cont.) The material to be drilled should be secured in a vise or with ciamps to keep it from turning as the drill bit rotates Hold your drill lirmly and place the bit at the point te be drilled, Depress the switch trigger to start your drill Move the drill bit into the workpiece applying only enough pressure to keep the bit cutting Do not force your drill or apply side pressure to elongate a hoie Let your drill and bit do the work See Fig 8 When drHting metals use a light oil on the drill btt to keep it from overheating, The oil will prolong the lile of the bit and increase the drilling action tf the bit jams in workpiece or tf the dtiH stalis, re_ease switch trigger immediately. Remove the bit from the workpiece and determine the reason for jamming Page 8
MAINTENANCE GENERAL Avoid using solvents when cleaning plastic parts Most plastics are susceptible to various types of oommeP cial solvents and may be damaged by their use, Use clean cloths to remove dirt, dust, oil, grease, etc, ACCESSORIES ...... THE FOLLOWING RECOMMENDED ACCESSORIES ARE CURRENT AND WERE ............. AVAILABLE AT THE TIME THIS MANUAL WAS PRINTED, 5,,Pc, Power Screwdriver Bit Set Cat, No 9 25602 No, 2 Phillips/8.,10 Slotted. 2 Ea Cat No 9 25603 No, 3 PhiUips/6-8 Stotted, 2 Ea Cat, No 9_ 25604 7,Pc Screwdriver Bit Set and Case Cat, No 9. 2555 Doweling Jig Cat No _9 4186 t3,Pc, Power Screwdriver/Nutdriver Set and Case Cat No,, 9 25653 30-Pc Power Screwdriver/Nutdriver Set and Case Cat No. 9 25654 7,Pc Power Nutdriver Bit Set Cat No 9_9 25655 t7,Pc Power Screwdriver/Nutdriver Set and Case Cat No.. 9 25657 High Speed Bits (For Wood or Metal) . ,. 3/8" Max,, Hole Square Cat No, __9 2596 _i'_'_='J_'!,lJJ[=]_The use ot attachments or accessories not listed might be hazardous,. q t REPLACEMENT PARTS WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS Part Number Description 999555_007 Battery Charger _ ,ll ii ii iq , ,Hll Ill " -- '_ ................... Page g
NOTES Page 10
NOTES Page 11
OWNERS MANUAL SERVICE MODEL NO. 315.111450 HOW TO ORDER REPAIR PARTS ............ :: ,L,Im. 1" 3/8 INCH CORDLESS DRILL SINGLE-SPEED REVERSIBLE Now that you have purchased your Drill, shoutd a need ever exist for tepai[ parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co, stores Be sure to provide all perti- nent facts when you call or visit. The model number of your Drill wiil be found on the plate attached to the motor housing. WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION: o PART NUMBER * MODEL NUMBER 315 1 11450 o PART DESCRIPTION ⢠NAME OF ITEM Cordless Drill All parts listed may be ordered from any Sears Ser- vice Center and most Sears stores If the parts you need are not stocked _ocally, your order will be electronically transmitted to a Sears Repair Parts Distribution Center for handling i ...................... -' ........... _ .............. ,,,,u, i i it,i ill i Hqu, p SEARS, ROEBUCK AND CO Dept 698/731A, Sears Tower, Chicago, IL 60684