Craftsman 917.27285 Owner's Manual

Owner's Manual IC.nFTSMnN°I LAWN TRACTOR 22.0 HP, 42" Mower Electric Start 6 Speed Transaxle Model No. 917.272850 This product has a low emission engine which operates IIL-.L_II differently from previously budt engines. Before you start the engine, read and understand this Owner's Manual. J IMPORTANT: Read and follow all Safety Rules and Instructions before operating this equipment. For answers to your questions about this product, Call: 1-800-659-5917 Sears Craftsman Help Line 5 am - 5 pm, Mon- Sat Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. Visit our Craftsman website:www.sears.com/craftsman
Warranty ................................................. 2 Maintenance ......................................... 17 Safety Rules ........................................... 3 Service and Adjustments ...................... 21 Product Specifications ............................ 6 Storage ................................................. 27 Assembly/P re-Operation ........................ 8 Troubleshooting .................................... 28 Operation .............................................. 11 Repair Parts .......................................... 32 Maintenance Schedule ......................... 17 Sears Service ......................... Back Cover LIMITED WARRANTY ON CRAFTSMAN RIDING EQUIPMENT For two (2) years from the date of purchase, if this Craftsman Riding Equipment is maintained, lubricated and tuned up according to the instructions in the owner's manual, Sears will repair or replace free of charge any parts that are found to be defective in material or workmanship according to the guidelines of coverage listed below. Sears will also provide free labor for these applicable warranted parts for the two full years. During the first 30 days of purchase, there will be no charges to service the product at your home for issues covered by this warranty. (See exclusions below). For your conve- nience, IN HOME warranty service will still be available after the first 30 days of pur- chase, but a trip charge will apply. This charge will be waived if the Craftsman product is dropped off at an authorized Sears location. For the nearest authorized Sears location, please call 1-800-4-MY-HOME®. This warranty applies only while this product is within the United States. This Warranty does not cover: • Expendable items which become worn during normal use, including but not limited to blades, spark plugs, air cleaners, belts, and oil filters. • Standard Maintenance Servicing, oil changes, or tune-ups • Tire replacement or repair caused by punctures from outside objects, such as nails, thorns, stumps, or glass. • Repairs necessary because of operator abuse, including but not limited to, damage caused by towing objects beyond the capability of the riding equipment, impacting objects that bend the frame or crankshaft, or over-speeding the engine. • Repairs necessary because of operator negligence, including but not limited to, elec- trical and mechanical damage caused by improper storage, failure to use the proper grade and amount of engine oil, failure to keep the deck clear of flammable debris, or failure to maintain the equipment according to the instructions contained in the owner's manual. • Engine (fuel system) cleaning or repairs caused by fuel determined to be contami- nated or oxidized (stale). In general, fuel should be used within 30 days of its pur- chase date. • Normal deterioration and wear of the exterior finishes, or product label replacement. • Riding equipment used for commercial or rental purposes. LIMITED WARRANTY ON BATTERY For ninety (90) days from date of purchase, if any battery included with this riding equip- ment proves defective in material or workmanship and our testing determines the battery will not hold a charge, Sears will replace the battery at no charge. During the first 30 days of purchase, there will be no charges to replace the battery at your HOME. After the first 30 days, for your convenience, IN-HOME warranty service will still be avail- able but a trip charge will apply. This charge will be waived if the Craftsman product is dropped off at an authorized Sears location. For the nearest authorized Sears location, please call 1-800-4-MY-HOME®. This battery warranty applies only while this product is within the United States. This warranty gives you specific legal rights, and you may also have other rights, which vary, from state to state. Sears, Roebuck and Co.,Dept.817WA, Hoffman Estates, IL 60179 2
IMPORTANT: This cutting machine is capable of amputating hands and feet and throw- ing objects. Failure to observe the following safety instructions could result in serious injury or death. _:_WARNING: In order to prevent ac- cidental starting when setting up, trans- porting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug. _WARNING: Do not coast down a hill in neutral, you may lose control of the tractor. _WARNING: Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Operate only at the lowest possible speed when on a slope. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause _u to lose control of your tractor. WARNING: Engine exhaust, some of its constituents, and certain vehicle compo- nents contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. _WARNING: Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling, I. GENERAL OPERATION • Read, understand, and follow all instruc- tions in the manual and on the machine before starting. • Only allow responsible adults, who are familiar with the instructions, to operate the machine. • Clear the area of objects such as rocks, toys, wire, etc., which could be picked up and thrown by the blade. • Be sure the area is clear of other people before mowing. Stop machine if anyone enters the area. • Never carry passengers. • Do not mow in reverse unless abso- lutely necessary. Always look down and behind before and while backing. • Be aware of the mower discharge direc- tion and do not point it at anyone. Do not operate the mower without either the entire grass catcher or the guard in place. • Slow down before turning. • Never leave a running machine unat- tended. Always turn off blades, set parking brake, stop engine, and remove keys before dismounting. • Turn off blades when not mowing. • Stop engine before removing grass catcher or unclogging chute. • Mow only in daylight or good artificial light. • Do not operate the machine while under the influence of alcohol or drugs. • Watch for traffic when operating near or crossing roadways. • Use extra care when loading or un- loading the machine into a trailer or truck. • Data indicates that operators, age 60 years and above, are involved in a large percentage of riding mower-related in- juries. These operators should evaluate their ability to operate the riding mower safely enough to protect themselves and others from serious injury. • Keep machine free of grass, leaves or other debris build-up which can touch hot exhaust / engine parts and burn. Do not allow the mower deck to plow leaves or other debris which can cause build- up to occur. Clean any oil or fuel spillage before operating or storing the machine. Allow machine to cool before storage. II. SLOPE OPERATION Slopes are a major factor related to loss- of-control and tipover accidents, which can result in severe injury or death. All slopes require extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it. 3
DO: • Mow up and down slopes, not across. • Remove obstacles such as rocks, tree limbs, etc. • Watch for holes, ruts, or bumps. Un- even terrain could overturn the machine. Tall grass can hide obstacles. • Use slow speed. Choose a low gear so that you will not have to stop or shift while on the slope. • Follow the manufacturer's recommend- ations for wheel weights or counter- weights to improve stability. • Use extra care with grass catchers or other attachments. These can change the stability of the machine. • Keep all movement on the slopes slow and gradual Do not make sudden changes in speed or direction. • Avoid starting or stopping on a slope. If tires lose traction, disengage the blades and proceed slowly straight down the slope. DO NOT: • Do not turn on slopes unless neces- sary, and then, turn slowly and gradually downhill, if possible. • Do not mow near drop-offs, ditches, or embankments. The mower could suddenly turn over if a wheel is over the edge of a cliff or ditch, or if an edge caves in. • Do not mow on wet grass. Reduced traction could cause sliding. • Do not try to stabilize the machine by putting your foot on the ground. • Do not use grass catcher on steep slopes. III. CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the ma- chine and the mowing activity. Neveras- sume that children will remain where you last saw them. • Keep children out of the mowing area and under the watchful care of another responsible adult. • Be alert and turn machine off if children enter the area. • Before and when backing, look behind and down for small children. • Never carry children. They may fall off and be seriously injured or interfere with safe machine operation. • Never allow children to operate the machine. • Use extra care when approaching blind corners, shrubs, trees, or other objects that may obscure vision. IV. SERVICE • Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive. - Use only an approved container. - Never remove gas cap or add fuel with the engine running. Allow engine to cool before refueling. Do not smoke. - Never refuel the machine indoors. - Never store the machine or fuel con- tainer inside where there is an open flame, such as a water heater. • Never run a machine inside a closed area. • Keep nuts and bolts, especially blade attachment bolts, tight and keep equip- ment in good condition. • Never tamper with safety devices. Check their proper operation regularly. • Keep machine free of grass, leaves, or other debris build-up. Clean oil or fuel spillage. Allow machine to cool before storing. • Stop and inspect the equipment if you strike an object. Repair, if necessary, before restarting. • Never make adjustments or repairs with the engine running. • Grass catcher components are subject to wear, damage, and deterioration, which could expose moving parts or allow objects to be thrown. Frequently check components and replace with manufacturer's recommended parts, when necessary. • Mower blades are sharp and can cut. Wrap the blade(s) or wear gloves, and use extra caution when servicing them. • Check brake operation frequently. Ad- just and service as required. 4
• Be sure the area is clear of other people before mowing. Stop machine if anyone enters the area. • Never carry passengers or children even with the blades off. • Do not mow in reverse unless abso- lutely necessary. Always look down and behind before and while backing. • Never carry children. They may fall off and be seriously injured or interfere with safe machine operation. • Keep children out of the mowing area and under the watchful care of another responsible adult. • Be alert and turn machine off if children enter the area. • Before and when backing, look behind and down for small children. • Mow up and down slopes (15 ° Max), not across. • Remove obstacles such as rocks, tree limbs, etc. • Watch for holes, ruts, or bumps. Uneven terrain could overturn the machine. Tall grass can hide obstacles. • Use slow speed. Choose a low gear so that you will not have to stop or shift while on the slope. • Avoid starting or stopping on a slope. If tires lose traction, disengage the blades and proceed slowly straight down the slope. • If machine stops while going uphill, disengage blades, shift into reverse and back down slowly. • Be not turn on slopes unless necessary, and then, turn slowly and gradually downhill, if possible. 5
i and Type: i Oil Type i (API-SF-SJ): PRODUCT SPECIFICATIONS i Gasoline Capacity 3.5 Unleaded Regular SAE 30 (above 32°F) SAE 5W-30 (below 32°F) Oil Capacity: W/Filter 4.0 Pints W/O Filter 3.75 Pints Spark Plug: (Gap: .040") Ground Speed (MPH): Champion QC 12YC Forward: 1st 1.2 2nd 1.5 3rd 2.4 4th 3.5 5th 4.8 6th 5.3 Reverse: 1.5 Tire Pressure: Front: 14 PSI Rear: 10 PSI Charging 3 Amps Battery System: 5 Amps Headlights Battery: Amp/Hr: 35 Min. CCA: 280 Case Size: U1R i Blade Bolt Torque: 27-35 Ft. Lbs. CONGRATULATIONS on your purchase of a new tractor. It has been designed, engineered and manufactured to give you the best possible dependability and performance. Should you experience any problem you cannot easily remedy, please contact a Sears or other qualified service center. We have competent, well-trained technicians and the proper tools to service or repair this tractor. Please read and retain this manual. The instructions will enable you to assemble and maintain your tractor properly. Always observe the "SAFETY RULES". CUSTOMER RESPONSIBILITIES • Read and observe the safety rules. • Follow a regular schedule in main- taining, caring for and using your tractor. • Follow the instructions under "Mainte- nance" and "Storage" sections of this owner's manual. _WARNING: This tractor is equipped with an internal combustion engine and should not be used on or near any unim- proved forest-covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the state of California the above is re- quired by law (Section 4442 of the Califor- nia Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest Sears service center (See REPAIR PARTS section of this manual). REPAIR PROTECTION AGREEMENTS Congratulations on making a smart pur- chase. Your new Craftsman® product is designed and manufactured for years of dependable operation. But like all prod- ucts, it may require repair from time to time. That's when having a Repair Protec- tion Agreement can save you money and aggravation. Purchase a Repair Protection Agreement now and protect yourself from unexpected hassle and expense. Here's what's included in the Agreement: • Expert service by our 12,000 profe- sional repair specialists. • Unlimited service and no charge for parts and labor on all covered repairs. • Product replacement if your covered product can't be fixed. • Discount of 10% from regular price of service and service-related parts not covered by the agreement; also, 10% off regular price of preventive mainte- nance check. • Fast help by phone- phone support from a Sears technician on products requiring in-home repair, plus conve- nient repair scheduling. Once you purchase the Agreement, a simple phone call is all that it takes for you to schedule service. You can call anytime day or night, or schedule a service ap- pointment online. Sears has over 12,000 professional repair specialists, who have access to over 4.5 million quality parts and accessories. That's the kind of professionalism you can count on to help prolong the life of your new purchase for years to come. Purchase your Repair Protection Agreement today! Some limitations and exclusions apply. For prices and additional information call 1-800-827-6655. SEARS INSTALLATION SERVICE For Sears professional installation of home appliances, garage door openers, water heaters, and other major home items, in the U.S.A. call 1-800-4-MY-HOME® 6
Steering Wheel Insert Steering Wheel (1) Hex Bolt 1/4-28 x 1-1/4 Steering Wheel Adapter @ (1) Locknut 1/2-20 (1) Large Flat Washer _St_oeritg @ (1) Locknut 1/4-28 Steering Extension Shaft Seat (1) Washer @ 17/32 x 1-3/16 x 12 Gauge _(1) Knob Keys (2) Keys For Future Use Slope Sheet Video Cassette 7
Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. Review the video cassette before you begin. TOOLS REQUIRED FOR ASSEMBLY A socket wrench set will make assembly easier. Standard wrench sizes you need are listed below. (1) 3/4"wrench (1) Pliers (2) 7/16" wrench (1) Utility knife (1) Tire pressure gauge When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel). TO REMOVE TRACTOR FROM CARTON UNPACK CARTON 1. Remove all accessible loose parts and parts boxes from carton. 2. Cut along dotted lines on all four pan- els of carton. Remove end panels and lay side panels flat. 3. Check for any additional loose parts or cartons and remove. BEFORE REMOVING TRACTOR FROM SKID ATTACH STEERING WHEEL ASSEMBLE EXTENSION SHAFT AND BOOT 1. Slide extension shaft onto lower steer- ing shaft. Align mounting holes in ex- tension and lower shafts and install 1/4 hex bolt and Iocknut. Tighten securely. IMPORTANT: Tighten bolt and nut se- curely to 10-12 ft. Ibs torque. 2. Place tabs of steering boot over tab slots in dash and push down to secure. INSTALL STEERING WHEEL 3. Position front wheels of the tractor so they are pointing straight forward. 4. Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension. 5. Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter. 6. Assemble large flat washer, 1/2 hex nut and tighten securely. 7. Snap steering wheel insert into center of steering wheel. Steering _ / Steering Wheel Boot Tabs Adapter_ '_' / Extension Sha 1/4 Locknut---'-""_ _.__ .__ _---'--1/4 Hex Bolt Lower . _-. _.- . Steer ng / _ -.. ., , "-. _Tab _- " _ _ _-" Slots 8. Remove protective materials from trac- tor hood and grill. IMPORTANT: Check for and remove any staples in skid that may puncture tires where tractor is to roll off skid. HOW TO SET UP YOUR TRACTOR CHECK BATTERY 1. Lift hood to raised position. NOTE: If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instruc- tions). 8
INSTALL SEAT Adjust seat before tightening adjustment knob. 1. Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor. 2. Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard. 3. Place seat on seat pan so head of shoulder bolts are positioned over the large slotted holes in pan. 4. Push down on seat to engage shoulder bolts in slots and pull seat towards rear of tractor. 5. Pivot seat and pan forward and as- semble adjustment knob and flat washer loosely. Do not tighten. 6. Lower seat into operating position and sit in seat. 7. Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down. 8. Get off seat without moving its ad- justed position. 9. Raise seat and tighten adjustment knob securely. Seatl Shoulder Bolts Flat Wa_.__ NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid. TO ROLLTRACTOR OFF SKID (See Operation section for location and function of controls) 1. Press lift lever plunger and raise attachment lift lever to its highest po- sition. 2. Release parking brake by depressing clutch/brake pedal. 3. Place gearshift lever in neutral (N) position. 4. Roll tractor forward off skid. 5. Remove banding holding deflector shield up against tractor. TO DRIVE TRACTOR OFF SKID (See Operation section for location and function of controls) • ILWARNING: Before starting, read, un- derstand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects. 1. Be sure all the above assembly steps have been completed. 2. Check engine oil level and fill fuel tank with gasoline. 3. Sit on seat in operating position, depress clutch/brake pedal and set the parking brake. 4. Place gear shift lever in neutral (N) position. 5. Press lift lever plunger and raise attachment lift lever to its highest posi- tion. 6. Start the engine. After engine has started, move throttle control to idle position. 7. Depress clutch/brake pedal into full "BRAKE" position and hold. Move gearshift lever to 1 st gear. 8. Slowly release clutch/brake pedal and slowly drive tractor off skid. 9. Apply brake to stop tractor, set park- ing brake and place gearshift lever in neutral position. 10.Turn ignition key to "STOP" position. Continue with the instructions that follow. 9
INSTALL MULCHER PLATE (If previously removed) 1. Raise and hold deflector shield in upright position. 2. Place front of mulcher plate over front of mower deck opening and slide into place, as shown. 3. Hook front latch into hole on front of mower deck. 4. Hook rear latch into hole on back of mower deck. Deflector Shield Mulcher Plate Latch Hooks _ILCAUTION: Do not remove deflector shield from mower. TO CONVERTTO BAGGING OR DISCHARGING Simply remove mulcher plate and store in a safe place.Your mower is now ready for discharging or installation of optional grass catcher accessory. NOTE: It is not necessary to change blades. The mulcher blades are designed for discharging and bagging also. CHECKTIRE PRESSURE The tires on your tractor were overin- flated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown in "PRODUCT SPECIFICATIONS" section of this manual. CHECK DECK LEVELNESS For best cutting results, mower hous- ing should be properly leveled. See "TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual. CHECK FOR PROPER POSITION OF ALL BELTS See the figures that are shown for replac- ing motion and mower blade drive belts in the Service and Adjustments section of this manual. Verify that the belts are routed correctly. CHECK BRAKE SYSTEM After you learn how to operate your trac- tor, check to see that the brake is properly adjusted. See "TO ADJUST BRAKE" in the Service and Adjustments section of this manual. ,/CHECKL IS T Before you operate and enjoy your new tractor, we wish to assure that you receive the best performance and satisfaction from this Quality Product. Please review the following checklist: ,/All assembly instructions have been completed. ,/No remaining loose parts in carton. ,/Battery is properly prepared and charged. (Minimum 1 hour at 6 amps). ,/Seat is adjusted comfortably and tight- ened securely. ,/All tires are properly inflated. (For ship- ping purposes, the tires were overin- flated at the factory). ,/Be sure mower deck is properly leveled side-to-side/front-to-rear for best cutting results. (Tires must be properly inflated for leveling). ,/Check mower and drive belts. Be sure they are routed properly around pulleys and inside all belt keepers. ,/Check wiring. See that all connections are still secure and wires are properly clamped. While learning how to use your tractor, pay extra attention to the following important items: ,/Engine oil is at proper level. ,/Fuel tank is filled with fresh, clean, regu- lar unleaded gasoline. ,/Become familiar with all controls - their location and function. Operate them before you start the engine. ,/Be sure brake system is in safe oper- ating condition. 10
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. R N H L I\I REVERSE NEUTRAL HIGH LOW CHOKE FAST SLOW IGNITION ENGINE OFF LIGHTS ON ENGINE ON ENGINE START PARKING BRAKE PARKING BRAKE PARKING BRAKE LOCKED UNLOCKED OVER TEMP FUEL OIL PRESSURE BATTERY REVERSE FORWARD MOWER HEIGHT MOWER LIFT LIGHT ATTACHMENT ATTACHMENT CLUTCH ENGAGED CLUTCH DISENGAGED FREE WHEEL (Automatic Models only) DANGER, KEEP HANDS AND FEET AWAY KEEP AREA CLEAR SLOPE HAZARDS (SEE SAFETY RULES SECTION) & Failure to follow instructions could result in serious injury or death. The safety alert symbol is used to identify safety inform- ation about hazards which can result in death, serious injury and/or property damage. & & & DANGER indicates a hazard which, if not avoided, will result in death or serious injury. WARNING indicates a hazard which, if not avoided, could result in death or serious injury. CAUTION indicates a hazard which, if not avoided, might result in minor or moderate injury. CAUTION when used without the alert symbol, indicates a situation that could result in damage to the tractor and/or engine. _HOT SURFACES indicates a hazard which, ,_l,., if not avoided, could result in death, serious injury and/or property damage. FIRE indicates a hazard which, if not avoided, could result in death, serious injury and/or property damage. 11
KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. Ammeter Choke Control Throttle Control Attachment Ignition Switch Light Switch Position Clutch Lever --. I "2"- Lever Plunger Attachment Lift Lever Clutch/Brake Pedal o Height Adjustment Lever Brake Lever Gearshift Lever Our tractors conform to the safety standards of the American National Standards Institute. AMMETER - Indicates charging ( ) or discharging (-) of battery. ATTACHMENT CLUTCH LEVER - Used to engage the mower blades, or other at- tachments mounted to your tractor. ATTACHMENT LIFT LEVER - Used to raise, lower, and adjust the mower deck or other attachments mounted to your tractor. CLUTCH/BRAKE PEDAL - Used for declutching and braking the tractor and starting the engine. GEARSHIFT LEVER - Selects the speed and direction of tractor. IGNITION SWITCH - Used for starting and stopping the engine. LIFT LEVER PLUNGER - Used to release attachment lift lever when changing its position. LIGHT SWITCH POSITION -Turns the headlights on and off. PARKING BRAKE LEVER - Locks clutch/ brake pedal into the brake position. THROTTLE CONTROL - Used for start- ing and controlling engine speed. CHOKE CONTROL - Used when starting a cold engine. 12
The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses. HOW TO USE YOU R TRACTOR TO SET PARKING BRAKE Your tractor is equipped with an operator presence sensing switch. When engine is running, any attempt by the operator to leave the seat without first setting the parking brake will shut off the engine. 1. Depress clutch/brake pedal all the way down and hold. 2. Pull parking brake lever up and release pressure from clutch/brake pedal. Pedal should remain in brake position. Make sure parking brake will hold trac- tor secure. Attachment Clutch Lever Position Choke _ inition Key ,"Disengaged" Thn Position Clutch/ Brake "Engaged" Position Broke Gearshift "Disengaged" "Brake" Lever Position Position STOPPING MOWER BLADES - • To stop mower blades, move attachment clutch lever to "DISENGAGED" position. GROUND DRIVE - • To stop ground drive, depress clutch/ brake pedal all the way down. • Move gearshift lever to neutral (N) position. ENGINE - • Move throttle control to slow position. NOTE: Failure to move throttle control to slow position and allowing engine to idle before stopping may cause engine to "backfire". • Turn ignition key to "STOP" position and remove key. Always remove key when leaving tractor to prevent unauthorized use. • Never use choke to stop engine. IMPORTANT: Leaving the ignition switch in any position other than "STOP" will cause the battery to discharge and go dead. NOTE: Under certain conditions when tractor is standing idle with the engine running, hot engine exhaust gases may cause "browning" of grass. To eliminate this possibility, always stop engine when Ocpping tractor on grass areas. AUTION: Always stop tractor com- pletely, as described above, before leaving the operator's position. TO USETHROTTLE CONTROL Always operate engine at full throttle. • Operating engine at less than full throttle reduces the battery charging rate. • Full throttle offers the best bagging and mower performance. TO USE CHOKE CONTROL Use choke control whenever you are start- ing a cold engine. Do not use to start a warm engine. • To engage choke control, pull knob out. Slowly push knob in to disengage. TO MOVE FORWARD AND BACKWARD The direction and speed of movement is controlled by the gearshift lever. 1. Start tractor with clutch/brake pedal de- pressed and gearshift lever in neutral (N) position. 2. Move gearshift lever to desired po- sition. 3. Slowly release clutch/brake pedal to start movement. IMPORTANT: Bring tractor to a complete stop before shifting or changing gears. Failure to do so will shorten the useful life of your transaxle. TO ADJUST MOWER CUTTING HEIGHT The position of the attachment lift lever determines the cutting height. • Grasp lift lever. • Press plunger with thumb and move lever to desired position. 13
The cutting height range is approxi- mately 1-1/2 to 4". The heights are mea- sured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed. • The average lawn should be cut to ap- proximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth. • For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height. TO ADJUST GAUGE WHEELS Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions. NOTE: Adjust gauge wheels with tractor on a flat level surface. 1. Adjust mower to desired cutting height (See "TO ADJUST MOWER CUTTING HEIGHT" in this section of manual). 2. With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in ap- propriate hole with shoulder bolt, 3/8 washer, and 3/8-16 Iocknut and tighten securely. 3. Repeat for opposite side, installing gauge wheel in same adjustment hole. Gauge Wheel o_% Mounting \ _-._ _ _/-_j_ Bracket 2_.___ Locknut --------_/_:_ _f\ _" Shoulder 3/8 Washer f ....-.-_,..._Bolt Gauge Wheel TO OPERATE MOWER Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. 1. Select desired height of cut. 2. Start mower blades by engaging at- tachment clutch control. TO STOP MOWER BLADES - disengage attachment clutch control. _,CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield in place. Clutch Lever Lift igh Position ,,,, Low Position "Disengaged" Position Shield TO OPERATE ON HILLS _WARNING: Do not drive up or down hills with slopes greater than 15 ° and do not drive across any slope. Use the slope guide at the back of this manual. • Choose the slowest speed before start- ing up or down hills. • Avoid stopping or changing speed on hills. • If slowing is necessary, move throttle control lever to slower position. • If stopping is absolutely necessary, push clutch/brake pedal quickly to brake posi- tion and engage parking brake. • Move gearshift lever to 1st gear. Be sure you have allowed room for tractor to roll slightly as you restart movement. • To restart movement, slowly release parking brake and clutch/brake pedal. • Make all turns slowly. TO TRANSPORT • Raise attachment lift to highest position with attachment lift control. • When pushing or towing your tractor, be sure gearshift lever is in neutral (N) position. • Do not push or tow tractor at more than five (5) MPH. NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.). 14
TOWING CARTS AND OTHER ATTACH- MENTS Tow only the attachments that are recom- mended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor. BEFORE STARTING THE ENGINE CHECK ENGINE OIL LEVEL The engine in your tractor has been shipped, from the factory, already filled with summer weight oil. 1. Check engine oil with tractor on level ground. 2. Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, re- move and read oil level. If necessary, add oil until "FULl" mark on dipstick is reached. Do not overfill. • For cold weather operation you should change oil for easier starting (See the oil viscosity chart in the Maintenance section of this manual). • To change engine oil, see the Mainte- nance section in this manual. ADD GASOLINE • Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quan- tities that can be used within 30 days to assure fuel freshness. _CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame. IMPORTANT: When operating in temper- atures below32°F(0°C), use fresh, clean winter grade gasoline to help insure good cold weather starting. CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separa- tion and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur. TO START ENGINE When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine. 1. Sit on seat in operating position, depress clutch/brake pedal and set parking brake. 2. Place gear shift lever in neutral (N) position. 3. Move attachment clutch to disengaged position. 4. Move throttle control to fast position 5. Pull choke control out for a cold engine start attempt. For a warm engine start attempt the choke control may not be needed. NOTE: Before starting, read the warm and cold starting procedures below. 6. Insert key into ignition and turn key clockwise to start position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, push choke control in, wait a few minutes and try again. If engine still does not start, pull the choke con- trol out and retry. WARM WEATHER STARTING (50 ° F and above) 7. When engine starts, slowly push choke control in until the engine begins to run smoothly. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly. • The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above. 15
COLD WEATHER STARTING (50 ° F and below) 7. When engine starts, slowly push choke control in until the engine begins to run smoothly. Continue to push the choke control in small steps allowing the en- gine to accept small changes in speed and load, until the choke control is fully in. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature. • The attachments can be used during the engine warm-up period and may require the choke control be pulled out slightly. NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance (see "TO ADJUST CARBURETOR" in the Service and Adjustments section of this manual). MOWING TIPS • Mower should be properly leveled for best mowing performance. See "TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trimming. • Drive so that clippings are discharged onto the area that has already been cut. Have the cut area to the right of the tractor. This will result in a more even distribution of clippings and more uniform cutting. • When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished. f ,m, 00272 If grass is extremely tall, it should be mowed twice to reduce load and pos- sible fire hazard from dried clippings. Make first cut relatively high; the second to the desired height. • Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing. • Always operate engine at full throttle when mowing to assure better mowing performance and proper discharge of material. Regulate ground speed by selecting a low enough gear to give the mower cutting performance as well as the quality of cut desired. • When operating attachments, select a ground speed that will suit the terrain and give best performance of the at- tachment being used. MULCHING MOWING TIPS IMPORTANT: For best performance, keep mower housing free of built-up grass and trash. Clean after each use. • The special mulching blade will recut the grass clippings many times and reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed. Also, the mulched grass will biodegrade quickly to provide nutrients for the lawn. Always mulch with your highest engine (blade) speed as this will provide the best recut- ting action of the blades. • Avoid cutting your lawn when it is wet. Wet grass tends to form clumps and interferes with the mulching action. The best time to mow your lawn is the early afternoon. At this time the grass has dried and the newly cut area will not be exposed to the direct sun. • For best results, adjust the mower cutting height so that the mower cuts off only the top one-third of the grass blades. For extremely heavy grass, re- duce your width of cut on each pass and mow slowly. MAX 1/3 • Certain types of grass and grass conditions may require that an area be mulched a second time to completely hide the clippings. When doing a sec- ond cut, mow across or perpendicular to the first cut path. • Change your cutting pattern from week to week. Mow north to south one week then change to east to west the next week. This will help prevent matting and graining of the lawn. 16
PILL 'N OATES AS YOU COMPLETE BE ° B SEBVICE OATHS Check Brake Operation _ _#, Check Tire Pressure Check Operator Presence and T Interlock Systems R Check for Loose Fasteners _ I_s J_ Sharpen/Replace Mower Blades i3 T Lubrication Chart 0 Check Battery Level R Clean Battery and Terminals Check Transaxle Cooling Check V-Belts Check Engine Oil Level I_ Change Engine Oil (with oil filter) _1,2 i,, E Change Engine Oil (without oil filter) _1,2 U Clean Air Filter G Clean Air Screen N_ Inspect MuffledSpark Attester I_ E Replace Oil Filter (If equipped) _,. Clean Engine Cooling Fins Replace Spark Plug _ I[_ Replace Air Filter Paper Cartridge _2 Fuel Filter Replace t = Change more often wben operating under a heavy load or 3 - Replace blades more often when mowing in sandy soil. in high ambient temperatures. 4 - Not required if equipped with maintenance-free battery. 2 - Service more often when operating in dirty or dusty conditions. 5 - Tighten front axle pivot bolt to 35 ft.dbs, maximum. DO not overtigbten. GENERAL RECOMMENDATIONS The warranty on this tractor does not @ Spindle cover items that have been subjected to Zerk ,, ;_ operator abuse or negligence. To receive _/_" full value from the warranty, operator //'L"-" ' must maintain tractor as instructed in this @Front Wheel -. manual. Bearing Some adjustments will need to be made Zerk /"/_" periodically to properly maintain your L/I tractor. ¢_,iL All adjustments in the Service and Adjust- @Engine ments section of this manual should be ,_ _, checked at least once each season. ,, ,, • Once a year you should replace the ,, ,_ spark plug, clean or replace air filter, , .... and check blades and belts for wear. A new spark plug and clean air filter assure proper air-fuel mixture and help your engine run better and last longer. BEFORE EACH USE 1. Check engine oil level. 2. Check brake operation. 3. Check tire pressure. 4. Check operator presence and interlock systems for proper operation. 5. Check for loose fasteners. LUBRICATION CHART @ Spindle / _ Zerk q @Front Wheel ===-=! i_Bearing Zerk , / I--]', _)Gearshift ]--_ i, Pivots _SAE 30 or 10w30 MOTOR OIL @GENERAL PURPOSE GREASE @REFER TO Maintenance "ENGINE" SECTION IMPORTANT: Do not oil or grease the pivot points which have special nylon bearings. Viscous lubricants will attract dust and dirt that will shorten the life of the self-lubricating bearings. If you feel they must be lubricated, use only a dry, pow- dered graphite type lubricant sparingly. 17
TRACTOR Always observe safety rules when per- forming any maintenance. BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See "TO ADJUST BRAKE" in the Service and Adjustments section of this manual). TIRES • Maintain proper air pressure in all tires (See "PRODUCT SPECIFICATIONS" section of this manual). • Keep tires free of gasoline, oil, or insect control chemicals which can harm rub- ber. • Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage. NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion. OPERATOR PRESENCE SYSTEM Be sure operator presence and interlock systems are working properly. If your trac- tor does not function as described, repair the problem immediately. • The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position. • When the engine is running, any at- tempt by the operator to leave the seat without first setting the parking brake should shut off the engine. • When the engine is running and the attachment clutch is engaged, any at- tempt by the operator to leave the seat should shut off the engine. • The attachment clutch should never op- erate unless the operator is in the seat. BLADE CARE For best results mower blades must be kept sharp. Replace bent or damaged blades. BLADE REMOVAL 1. Raise mower to highest position to al- low access to blades. 2. Remove blade bolt, lock washer and flat washer securing blade. 3. Install new or resharpened blade with trailing edge up towards deck as shown. IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly. 4. Reassemble blade bolt, lock washer and flat washer in exact order as shown. 5. Tighten blade bolt securely (27-35 Ft. Lbs. torque). IMPORTANT: Blade bolt is grade 8 heat treated. Mandrel Assembly Trailing _. BI_,4^ _ _,u_ n r Edge Up //'_"] _ Ce te _"_'_ Rat Wha_her __ Lock Washer......._%__ Star _---Blade Bolt (Grade)* *A Grade 8 heat treated bolt can be identified by six lines on the bolt head. TO SHARPEN BLADE NOTE: We do not recommend sharp- ening blade - but if you do, be sure the blade is balanced. Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and eventual damage to mower and engine. • The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower. • To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer.) NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not. • Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced. 5/8" Bolt or Pin Center Hole BATTERY Your tractor has a battery charging system which is sufficient for normal use. How- ever, periodic charging of the battery with an automotive charger will extend its life. • Keep battery and terminals clean. • Keep battery bolts tight. 18
• Keep small vent holes open. • Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary. TO CLEAN BATTERY AND TERMINALS Corrosion and dirt on the battery and terminals can cause the battery to "leak" power. 1. Remove terminal guard. 2. Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor. 3. Rinse the battery with plain water and dry. 4. Clean terminals and battery cable ends with wire brush until bright. 5. Coat terminals with grease or petro- leum jelly. 6. Reinstall battery (See "REPLACING BATTERY" in the SERVICE AND AD- JUSTMENTS section of this manual). TRANSAXLE COOLING Keep transaxle free from build-up of dirt and chaff which can restrict cooling. Check the crankcase oil level before start- ing the engine and after each eight (8) hours of operation. Tighten oil fill cap/ dipstick securely each time you check the oil level. TO CHANGE ENGINE OIL Determine temperature range expected before oil change. All oil must meet API service classification SF-SJ. • Be sure tractor is on level surface. • Oil will drain more freely when warm. • Catch oil in a suitable container. 1. Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine when changing oil. 2. Remove yellow cap from end of drain valve and install the drain tube onto the fitting. Oil Drain Valve Closed and Locked Position V-BELTS Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. ENGINE LUBRICATION Only use high quality detergent oil rated with API service classification SF-SJ. Select the oil's SAE viscosity grade according to your expected operating temperature. SAE V_SCOSITY GRADES loo TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°E Check your engine oil level more frequently to avoid possible engine damage from running low on oil. Change the oil after every 50 hours of op- eration or at least once a year if the tractor is not used for 50 hours in one year. 19 Drain Tube 3. Unlock drain valve by pushing inward slightly and turning counterclockwise. 4. To open, pull out on the drain valve. 5. After oil has drained completely, close and lock the drain valve by pushing inward and turning clockwise until the pin is in the locked position as shown. 6. Remove the drain tube and replace the cap onto the end of the drain valve. 7. Refill engine with oil through oil fill dip- stick tube. Pour slowly. Do not overfill. For approximate capacity see "PROD- UCT SPECIFICATIONS" section of this manual. 8. Use gauge on oil fill cap/dipstick for checking level. For accurate reading, tighten dipstick cap securely onto the tube before removing dipstick. Keep oil at "FULl" line on dipstick. Tighten cap onto the tube securely when finished.
ENGINE OIL FILTER Replace the engine oil filter every season or every other oil change if the tractor is used more than 100 hours in one year. AIR FILTER Your engine will not run properly using a dirty air filter. Clean the foam pre-cleaner after every 25 hours of operation or every season. Service paper cartridge every 100 hours of operation or every season, whichever occurs first. Service air cleaner more often under dusty conditions. 1. Remove knobs and cover. TO SERVICE PRE-CLEANER 2. Wash it in liquid detergent and water. 3. Squeeze it dry in a clean cloth. 4. Saturate it in engine oil. Wrap it in clean, absorbent cloth and squeeze to remove excess oil. NOTE: If very dirty or damaged, replace pre-cleaner. TO SERVICE CARTRIDGE 1. Clean cartridge by tapping gently on flat surface. If very dirty or damaged, replace cartridge. 2. Reinstall precleaner cartridge, cover and secure with knobs. IMPORTANT: Petroleum solvents, such as kerosene, are not to be used to clean the cartridge. They may cause deterio- ration of the cartridge. Do not oil cartridge. Do not use pressurized air to clean or dry cartridge. .... _ .... Cartridge Cover __ Foam __ Pre-Cleaner " 7_--,-_.. _- CLEAN AIR SCREEN Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stub- born dried gum fibers. CLEAN AIR INTAKE/COOLING AREAS To insure proper cooling, make sure the grass screen, cooling fins, and other exter- nal surfaces of the engine are kept clean at all times. Every 100 hours of operation (more often under extremely dusty, dirty conditions), remove the blower housing and other cool- ing shrouds. Clean the cooling fins and external surfaces as necessary. Make sure the cooling shrouds are reinstalled. NOTE: Operating the engine with a blocked grass screen, dirty or plugged cooling fins, and/or cooling shrouds removed will cause engine damage due to overheating. MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could cre- ate a fire hazard and/or damage. SPARK PLUG(S) Replace spark plug(s) at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in "PRODUCT SPECIFICATIONS" section of this manual. IN-LINE FUEL FILTER The fuel filter should be replaced once each season. If fuel filter becomes clogged, obstructing fuel flow to carbu- retor, replacement is required. 1. With engine cool, remove filter and plug fuel line sections. 2. Place new fuel filter in position in fuel line with arrow pointing towards carbu- retor. 3. Be sure there are no fuel line leaks and clamps are properly positioned. 4. Immediately wipe up any spilled gaso- line. CLEANING • Clean engine, battery, seat, finish, etc. of all foreign matter. • Keep finished surfaces and wheels free of all gasoline, oil, etc. • Protect painted surfaces with auto- motive type wax. We do not recommend using a garden hose or pressure washer to clean your tractor unless the engine and transmis- sion are covered to keep water out. Water in engine or transmission will shorten the useful life of your tractor. Use compressed air or a leaf blower to remove grass, leaves and trash from tractor and mower. 20
_b ARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: 1. Depress clutch/brake pedal fully and set parking brake. 2. Place gearshift lever in neutral (N) position. 3. Place attachment clutch in "DISENGAGED" position. 4. Turn ignition key to "STOP" and remove key. 5. Make sure the blades and all moving parts have completely stopped. 6. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. TRACTOR TO REMOVE MOWER Mower will be easier to remove from the right side of tractor. 1. Place attachment clutch in "DISEN- GAGED" position. 2. Move attachment lift lever forward to lower mower to its lowest position. 3. Roll belt off engine pulley. 4. Remove small retainer spring, and remove clutch spring off pulley bolt. 5. Remove large retainer spring, slide collar off and push housing guide out of bracket. 6. Disconnect anti-sway bar from chassis bracket by removing retainer spring. 7. Disconnect suspension arms from rear deck brackets by removing retainer springs. 8. Disconnect front links from deck by removing retainer springs. 9. Raise lift lever to raise suspension arms. Slide mower out from under trac- tot. Small Retainer Clutch Spring -- Small Retainer Clutch Spring _ Spring _ _- Retainer Spring IMPORTANT: If an attachment other than the mower deck is to be mounted on the tractor, remove the front links and hook the clutch spring Into square hole in frame. TO INSTALL MOWER 1. Raise attachment lift lever to its highest position. 2. Slide mower under tractor with deflec- tor shield to right side of tractor. 3. Lower lift lever to its lowest position. 4. Connect front links to mower deck and secure with retainer springs. 5. Connect suspension arms to rear deck brackets and secure with retainer springs. 6. Connect anti-sway bar to chassis bracket and secure with retainer spring. 7. Push clutch cable housing guide into bracket, slide collar onto guide and secure with large retainer spring. 8. Place flat washer and clutch spring on idler pulley bolt and secure with small retainer spring. 9. Install belt onto engine pulley. Flat Washer _.'_;_ _-_ Square Hole Engine Pulley Anti-Sway Bar Collar Housir Guide \ Large Retainer Spring Bracket 21 Retainer Springs (Both Sides) \ Deflector / Shield
TO LEVEL MOWER HOUSING Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See "PROD- UCT SPECIFICATIONS" section of this manual). If tires are over or underinflated, you will not properly adjust your mower. SIDE-TO-SIDE ADJUSTMENT • Raise mower to its highest position. • At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance "A" on both sides of mower should be the same or within 1/4" of each other. • If adjustment is necessary, make adjust- ment on one side of mower only. • To raise one side of mower, tighten lift link adjustment nut on that side. • To lower one side of mower, loosen lift link adjustment nut on that side. NOTE: Each full turn of adjustment nut will change mower height about 1/8". • Recheck measurements after adjusting. Bottom edge of Bottom edge mower to ground of mower to _-_ ground ___/ U Suspension Arm • To lower front of mower loosen nut "E" on both front links an equal number of turns. • When distance "D" is 1/8" to 1/2" lower at front than rear, tighten nuts "F" against trunnion on both front links. • To raise front of mower, loosen nut "F" from trunnion on both front links. Tighten nut "E" on both front links an equal num- ber of turns. The two front links must remain equal in length. • When distance "D" is 1/8" to 1/2" lower at front than rear, tighten nut "F" against trunnion on both front links. • Recheck side-to-side adjustment. _g _ Both Front Links Should be Equal in Length =t "E" mru Lift Link Adjustment Nut FRONT-TO-BACK ADJUSTMENT IMPORTANT: Deck must be level side-to side. If the following front-to-back adjust- ment is necessary, be sure to adjust both front links equally so mower will stay level side-to-side. To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position. Check adjustment on right side of tractor. Measure distance "D" directly in front and behind the mandrel at bottom edge of mower housing as shown. • Before making any necessary adjust- ments, check that both front links are equal in length. • If links are not equal in length, adjust one link to same length as other link. TO REPLACE MOWER BLADE DRIVE BELT The mower blade drive belt may be re- placed without tools. Park the tractor on level surface. Engage parking brake. BELT REMOVAL - 1. Remove mower from tractor (See "TO REMOVE MOWER" in this section of manual). 2. Work belt off both mandrel pulleys and idler pulleys. 3. Pull belt away from mower. BELT INSTALLATION - 1. Work belt around both mandrel pulleys and idler pulleys 2. Make sure belt is in all pulley grooves and inside all belt guides. 3. Install mower (See "To Install Mower" in this section of this manual). 22
With parking brake "Engaged" Mandrel _ Nut Arm Pulley TO CHECK AND ADJUST BRAKE Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle. If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. TO CHECK BRAKE 1. Park tractor on a level, dry concrete or paved surface, depress clutch/brake pedal all the way down and engage parking brake. 2. Place gear shift lever in neutral (N) position. The rear wheels must lock and skid when you try to manually push the tractor for- ward. If the rear wheels rotate, the brake needs to be adjusted or the pads need to be replaced. TO ADJUST BRAKE 1. Depress clutch/brake pedal all the way down and engage parking brake. 2. Measure distance between brake oper- ating arm and nut "A" on brake rod. 3. If distance is other than 1-1/2", loosen jam nut and turn nut "A" until distance becomes 1-1/2". Retighten jam nut against nut "A". 4. Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than five (5) feet in highest gear, further maintenance is neces- sary. Replace brake pads or contact a Sears or other qualified service center. TO REPLACE MOTION DRIVE BELT Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest. BELT REMOVAL - 1. Remove mower (See "TO REMOVE MOWER" in this section of manual). NOTE: Observe entire motion drive belt and position of all belt guides and keepers. 2. Remove belt from stationary idler and clutching idler. 3. Remove belt downward from around engine pulley. 4. Pull belt slack toward rear of tractor. Remove belt upwards from transaxle pulley by deflecting belt keepers. 5. Remove belt from center span keeper and pull belt away from tractor. BELT INSTALLATION - 1. Carefully work new belt down between transaxle belt keepers and onto the input pulley. 2. Slide belt into the center span keeper. 3. Pull belt toward front of tractor and roll around the top groove of engine pulley. 4. Install belt through stationary idler and clutching idler. 5. Make sure belt is in all pulley grooves and inside all belt guides and keepers. 6. Install mower (See "TO INSTALL MOWER" in this section of manual). 23
Engine Pulle Clutching Stationary Keeper Transaxle Pulley TRANSAXLE GEAR SHIFT LEVER NEU- TRAL ADJUSTMENT The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows: 1. Make sure transaxle is in neutral (N). NOTE: When the tractor rear wheels move freely, the transaxle is in neutral. 2. Loosen adjustment bolt in front of the right rear wheel. 3. Position the gear shift lever in the neu- tral (N) position. 4. Tighten adjustment bolt securely. NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position. Gearshift Lever Neutral Lock Gate Adjustment Bolt TO ADJUST STEERING WHEEL ALIGN- MENT If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble with crossbars horizontal. Tighten securely. FRONT WHEEL TOE-IN/CAMBER The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact a Sears or other qualified service center. TO REMOVE WHEEL FOR REPAIRS 1. Block up axle securely. 2. Remove axle cover, retaining ring and washers to allow wheel removal (rear wheels have a square key - Do not lose). 3. Repair tire and reassemble. NOTE: On rear wheels only: align grooves in rear wheel hub and axle. Insert square key. 4. Replace washers and snap retaining ring securely in axle groove. 5. Replace axle cover. NOTE: To seal tire punctures and prevent flat tires due to slow leaks, purchase and use tire sealant from Sears. Tire sealant also prevents tire dry rot and corrosion. Washers Retaining Rin Axle Cover I Square Key (Rear Wheel Only) TO START ENGINE WITH A WEAK BAT- TERY _WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from bat- teries. Always wear eye protection when around batteries. If your battery is too weak to start the engine, it should be recharged. (See "BAT- TERY" in the MAINTENANCE section of this manual). If "jumper cables" are used for emergency starting, follow this procedure: IMPORTANT: Your tractor is equipped with a 12 volt system. The other vehicle must also be a 12 volt system. Do not use your tractor battery to start other vehicles. TO ATTACH JUMPER CABLES - 1. Connect one end of the RED cable to the POSITIVE ( ) terminal of each battery(A-B), taking care not to short against tractor chassis. 2. Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery. 3. Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery. 24
TO REMOVE CABLES, REVERSE ORDER - 1. BLACK cable first from chassis and then from the fully charged battery. 2. RED cable last from both batteries. Weak or Dead Fully Charged Battery Battery REPLACING BATTERY _WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding. 1. Lift hood to raised position. 2. Remove terminal guard. 3. Disconnect BLACK battery cable then RED battery cable and carefully remove battery from tractor. 4. Install new battery with terminals in same position as old battery. 5. Reinstall terminal guard. 6. First connect RED battery cable to positive ( ) battery terminal with hex bolt and keps nut as shown. Tighten securely. 7. Connect BLACK grounding cable to negative (-) battery terminal with re- maining hex bolt and keps nut. Tighten securely 8. Close terminal access doors. 9. Close hood. TO REPLACE HEADLIGHT BULB 1. Raise hood. 2. Pull bulb holder out of the hole in the backside of the grill. 3. Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill. 4. Close hood. INTERLOCKS AND RELAYS Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting. • Check wiring. See electrical wiring diagram in the Repair Parts section. TO REPLACE FUSE Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash. TO REMOVE HOOD AND GRILL AS- SEMBLY 1. Raise hood. 2. Unsnap headlight wire connector. 3. Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor. 4. When replacing hood, be sure to re- connect the headlight wire connector. Hood Hex Bolt Nut Terminal Access __ ,. Door ' _ Terminal Guard Positive Cable ,Negative (Black) Cable 25
ENGINE Maintenance, repair, or replacement of the emission control devices and systems, which are being done at the customers ex- pense, may be performed by any non-road engine repair establishment or individual. Warranty repairs must be performed by an authorized engine manufacturer's service outlet. TO ADJUSTTHROTTLE CONTROL CABLE The throttle control has been preset at the factory and adjustment should not be nec- essary. Check adjustment as described below before loosening cable. If adjust- ment is necessary, proceed as follows: 1. With engine not running, move throttle control lever to fast position. 2. Check that swivel is against stop. If it is not, loosen cable clamp screw and pull cable back until swivel is against stop. Tighten cable clamp screw securely. TO ADJUST CHOKE CONTROL The choke control has been preset at the factory and adjustment should not be nec- essary. Check adjustment as described below before loosening cable. If adjust- ment is necessary, proceed as follows: 1. With engine not running, move choke control (located on dash panel) to full choke position. 2. Loosen knob and remove cover as- sembly from air cleaner. 3. Choke should be closed. If it is not, loosen casing clamp screw and move choke cable until choke is completely closed. Tighten casing clamp screw securely. 4. Replace air cleaner cover assembly and tighten knob. TO ADJUST CARBURETOR Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair and/or adjustment. High speed stop is factory adjusted. Do not adjust - damage may result. IMPORTANT: Never tamper with the engine governor, which is factory set for proper engine speed. Overspeed- ing the engine above the factory high speed setting can be dangerous. If you think the engine-governed high speed needs adjusting, contact a Sears or other qualified service center,, which has proper equipment and experience to make any necessary adjustments. Swivel Clamp Screw Clamp Screw 26
Immediately prepare your tractor for stor- age at the end of the season or if the trac- tor will not be used for 30 days or more. _WARNING: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure. TRACTOR Remove mower from tractor for winter storage. When mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area. 1. Clean entire tractor (See"CLEANING" in the Maintenance section of this manual). 2. Inspect and replace belts, if necessary (See belt replacement instructions in the Service and Adjustments section of this manual). 3. Lubricate as shown in the Maintenance section of this manual. 4. Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary. 5. Touch up all rusted or chipped paint surfaces; sand lightly before painting. BATTERY • Fully charge the battery for storage. • After a period of time in storage, battery may require recharging. • To help prevent corrosion and power leakage during long periods of storage, battery cables should be disconnected and battery cleaned thoroughly (see "TO CLEAN BATTERY AND TERMINALS" in the Maintenance section of this manual). • After cleaning, leave cables discon- nected and place cables where they cannot come in contact with battery terminals. • If battery is removed from tractor for storage, do not store battery directly on concrete or damp surfaces. ENGINE FUEL SYSTEM IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can dam- age the fuel system of an engine while in storage. 1. Drain the fuel tank. 2. Start the engine and let it run until the fuel lines and carburetor are empty. • Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur. • Use fresh fuel next season. NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or stor- age container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the car- buretor. Do not drain the gas tank and carburetor if using fuel stabilizer. ENGINE OIL Drain oil (with engine warm) and replace with clean engine oil. (See "ENGINE" in the Maintenance section of this manual). CYLINDER(S) 1. Remove spark plug(s). 2. Pour one ounce of oil through spark plug hole(s) into cylinder(s). 3. Turn ignition key to start position for a few seconds to distribute oil. 4. Replace with new spark plug(s). OTHER • Do not store gasoline from one season to another. • Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems. • If possible, store your tractor indoors and cover it to give protection from dust and dirt. • Cover your tractor with a suitable pro- tective cover that does not retain mois- ture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your tractor to rust. IMPORTANT: Never cover tractor while engine and exhaust areas are still warm. 27
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM Will not start Hard tostart Engine will not turn over Engine clicks but will not start CAUSE CORRECTION 1. Out of fuel. 2. Engine not "CHOKED" properly. 3. Engine flooded. . 5. 6. 7 1. Fill fuel tank. 2. See "TO START ENGINE" in Operation section. 3. Wait several minutes before attempting to start. Replace spark plug. Clean/replace air filter. Replace fuel filter. Drain fuel tank and carburetor, refill tank with fresh gasoline and replace fuel filter. 8. Check all wiring. 9. See "To Adjust Carburetor" in Service and Adjustments section. 10.Contact a Sears or other qualified service center. Bad spark plug. 4. Dirty air filter. 5. Dirty fuel filter. 6. Water in fuel. 7. 8. Loose or damaged wiring. 9. Carburetor out of adjustment. 10. Engine valves out of adjustment. 1. Dirty air filter. 2. Bad spark plug. 3. Weak or dead battery. 4. Dirty fuel filter. 5. Stale or dirty fuel. . 7. . . 2. 3. 4. 5. 6. 7. 8. 9. . 2. 3. 4. . 2. 3. . 5. Loose or damaged wiring. 6. Carburetor out of adjustment. 7. Engine valves out of 8. adjustment. Clutch/brake pedal not 1. depressed. Attachment clutch is 2. engaged. Weak or dead battery. 3. Blown fuse. 4. Corroded battery terminals. 5. Loose or damaged wiring. 6. Faulty ignition switch. 7. Faulty solenoid or starter. 8. Faulty operator presence 9. switch(es). Weak or dead battery. 1. Corroded battery terminals. 2. Loose or damaged wiring. 3. Faulty solenoid or starter. 4. Clean/replace air filter. Replace spark plug. Recharge or replace battery. Replace fuel filter. Drain fuel tank and refill with fresh gasoline. Check all wiring. See "To Adjust Carburetor" in Service and Adjustments section. Contact a Sears or other qualified service center. Depress clutch/brake pedal. Disengage attachment clutch. Recharge or replace battery. Replace fuse. Clean battery terminals. Check all wiring. Check/replace ignition switch. Check/replace solenoid or starter. Contact a Sears or other qualified service center. Recharge or replace battery. Clean battery terminals. Check all wiring. Check/replace solenoid or starter. 28
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center CAUSE CORRECTION . 2. 3. 4. 5. 6. 7. Dirty fuel filter. 8. Stale or dirty fuel. PROBLEM Loss of power Excessive vibration Engine continues to run when operator leaves seat with with attachment clutch engaged Poor cut - uneven 9. Water in fuel. Cutting too much grass/too fast. Throttle in "CHOKE" position. Build-up of grass, leaves 3. and trash under mower. Dirty air filter. 4. Low oil level/dirty oil. 5. Faulty spark plug. 6. 7. 8. 9. 10.Spark plug wire loose. 11. Dirty engine air screen/fins. 12. Dirty/clogged muffler. 13. Loose or damaged wiring. 14. Carburetor out of adjustment. 15. Engine valves out of adjustment. 1. Worn, bent or loose blade. 2. Bent blade mandrel. 3. Loose/damaged part(s). 1. Faulty operator-safety presence control system. Worn, bent or loose blade. Mower deck not level. Buildup of grass, leaves, and trash under mower. Bent blade mandrel. Clogged mower deck vent holes from buildup of grass, leaves, and trash around mandrels. . 2. 3. 4. 5. 1. Set in "Higher Cut" position/ reduce speed. 2. Adjust throttle control. Clean underside of mower housing. Clean/replace air filter. Check oil level/change oil. Clean and regap or change spark plug. Replace fuel filter. Drain fuel tank and refill with fresh gasoline. Drain fuel tank and carbure- tor, refill tank with fresh gasoline and replace fuel filter. 10. Connect and tighten spark plug wire. 11. Clean engine air screen/fins. 12. Clean/replace muffler. 13.Check all wiring. 14. See "To Adjust Carburetor" in Service and Adjustments section. 15. Contact a Sears or other qualified service center. 1. Replace blade. Tighten blade bolt. 2. Replace blade mandrel. 3. Tighten loose part(s). Replace damaged parts. . Check wiring, switches and connections. If not contact a Sears or other qualified service center. 1. Replace blade. Tighten blade bolt. 2. Level mower deck. 3. Clean underside of mower housing. 4. Replace blade mandrel. 5. Clean around mandrels to open vent holes. 29
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM Mower blades will not rotate Poor grass discharge CAUSE CORRECTION 1. Remove obstruction. 1. Obstruction in clutch mechanism. 2. Worn/damaged mower drive belt. 3. Frozen idler pulley. 4. Frozen blade mandrel. 1. Engine speed too slow. 2. Travel speed too fast. 3. Wet grass. 4. Mower deck not level. 5. Low/uneven tire air pressure. 6. Worn, bent or loose blade. 7. Buildup of grass, leaves and trash under mower. 8. Mower drive belt worn. 9. Blades improperly installed. 10. Improper blades used. 11. Clogged mower deck vent holes from buildup of grass, leaves, and trash around mandrels. i Headlight(s) not 1. i working 2. i(if so equipped) 3. 4. 5. i Battery will not 1. charge 2. 3. 4. 1. Engine "backfires" iwhen turn ng engine "OFF" Switch is "OFF". Bulb(s) or lamp(s) burned out. Faulty light switch. Loose or damaged wiring. Blown fuse. Bad battery cell(s). Poor cable connections. Faulty regulator (if so equipped). Faulty alternator. Engine throttle control not set at "SLOW" position for 30 seconds before stopping engine. 2. Replace mower drive belt. 3. Replace idler pulley. 4. Replace blade mandrel. 1. Place throttle control in "FAST" position. 2. Shift to slower speed. 3. Allow grass to dry before mowing. 4. Level mower deck. 5. Check tires for proper air pressure. 6. Replace/sharpen blade. Tighten blade bolt. 7. Clean underside of mower housing. 8. Replace mower drive belt. 9. Reinstall blades sharp edge down. 10. Replace with blades listed in this manual. 11. Clean around mandrels to open vent holes. 1. Turn switch "ON". 2. Replace bulb(s) or lamp(s). 3. Check/replace light switch. 4. Check wiring and connec- tions. 5. Replace fuse. 1. Replace battery. 2. Check/clean all connec- tions. 3. Replace regulator. 4. Replace alternator. . Move throttle control to "SLOW" position and allow to idle for 30 seconds before stopping engine. 30
TRACTOR - - MODEL NUMBER 917.272850 SCHEMATIC "I" RED 01115 BLACK BATTERY /7 ] SOLENOID STARTER IGNITION SWITCH RED WHITE J CLUTCH / BRAKJE (PEDAL UP) BLACK BLACK 8LACK WHETE __J SEAT SWITCH (NOT OCCUPIED) i i I i I '0 '°LACK _A_'MENi CLUTCH _ ' GROUNDING 8LACK (CLUTCH OFF) J CONNECTOR 1 {OPTIONAL) IGNITION UNIT FUEL SHUT-OFF SOLENOID (IF SO EQUIPPED) ORANGE A • SPARK • _@ PLUG GAP H (2 PLUGS ON TWiN CYL, ENGINES) CHARGING SYST£M OUTPUT 28 VOLTS AC MEN @ 3600 RpM 3 AMP DC @ 3600 R PM ICHARG_NG SYSTEM DISCONNECTED I \ _4 VOLTS AC MIN @ 3600 RPM (LIGHTS OFF) HEADLIGHTS // BLACK BROWN NOTE YOUR TRACTOR IS EQUIPPED WITH A SPECIAL ALTERNATOR SYSTEM. THE LIGHTS ARE NOT CONNECTED TO THE BATTERY, BUT HAVE THEIR OWN ELECTRICAL SOURCE. BECAUSE OF THIS, THE BRIGHTNESS OF THE LIGHTS WILL CHANGE WITH ENGINE SPEED. AT IDLE THE LIGHTS WILL DIM. AS THE ENGINE IS SPEEDED UP, THE LIGHTS WILL BECOME THEIR BRIGHTEST. NON-REMOVABLE CONNECTIONS IGNITION SWITCH POSITION CIRCUIT "MARE" OFF M G A1 NONE RUN/LIGH] B A1 A2 L RUN B A1 NONE START 3 S A1 NONE REMOVABLE CONNECTIONS WIRING INSULATED CLIPS NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR SERVICING OF UNIT, THEY SHOULD BE REPLACED TO PROPERLY SECURE YOUR WIRING. 31
TRACTOR - - MODEL NUMBER 917.272850 ELECTRICAL I I 42 I i 41 25 [ I I I i 27 22 21 I I I I 26 I I [i I / I / I I / i 16 52 ¸ 29 \ \ I / I / _ _ I / / i I // I / I / _\ / i \ / I I I I I I I I 32
TRACTOR - - MODEL NUMBER 917.272850 ELECTRICAL KEY PART NO, NO. DESCRIPTION 1 144927 Battery 2 74760412 Bolt Hex Hd 1/4-20unc x 3/4 8 7603J Case Battery 10 145211 Bolt, Btr Front 1/4-20 x 7-1/2 11 150109 Holddown Battery Front Mount 12 145769 Nut, Push Nylon Battery Front 1/4 16 176138 Switch, Interlock Push-tn 21 183759 Harness Light Socket (W/4152j) 22 4152J Bulb Light #1156 24 4799J Cable Battery 25 146148 Cable Battery 26 175158 Fuse 27 73510400 Nut Keps Hex 1/4-20 Uric 28 145491 Cable Ground 29 121305X Switch Seat 30 175566 Switch lgn 33 140403 Key Molded Craftsman 40 179720 Harness lgn 41 71110408 Bolt BIk. Fin Hex 1/4-20 Uric x 1/2 42 131563 Cover Terminal 43 178861 Solenoid 45 121433X Ammeter Rectangular 6 Amp 52 141940 Protection Wire Loop 55 17490508 Screw Thdrol 5/16-18 x 1/2 NOTE: All component dimensions given in U. S. inches 1 inch = 25.4 mm 33
TRACTOR -- MODEL NUMBER 917.272850 CHASSIS AND ENCLOSURES 259 260 258 28 261 39 58 222 _159 208 207 209 2O8 219 j64 2O 23 219 74 60 F142 _3 _145 208 ch_ssis-Laser -lt.stlt 21 34
TRACTOR -- MODEL NUMBER 917.272850 CHASSIS AND ENCLOSURES KEY PART NO. NO. DESCRIPTION 1 174619 Chassis 2 176554 Drawbar 3 17060612 Screw 3/8-16 x 3/4 5 155272 Bumper Hood/Dash 9 168337X013 Dash 10 STD533710 Bolt, Carriage 3/8-16 x 1 11 174996 Panel, Dash, L.H. 13 172105X010 Panel, Dash, R.H. 14 17490608 Screw Thdrol 3/8-16 x 1/2 17 185682X613 Hood Assembly 18 184921 Bumper Hood 20 180679 Plate Mtg. Battery/Tank 23 124028X Bushing 26 STD541437 Nut 28 184247 Grille 30 175692X613 Fend/Ftrest 31 139976 Bracket, Fender Support 37 17490508 ScrewThdrol 5/16-18x 1/2 38 175710 Pivot Bracket Assembly, Rear 39 174714 Bracket Pivot Laser Lt 58 174930 Duct Air Engine 60 72140606 Bolt Rdhd Sqnk 3/8-16 Uric x 3/4 64 154798 Dash Lower STLT 74 STD541437 Nut Crownlock 3/8016 Unc 114 158112 Keeper Belt Rear Lh Stl P930 115 17060620 Screw 3/8-16 x 1-1/4 142 175702 Plate Reinforcement STLT 143 154966 Bracket Swaybar Chassis 144 175582 Bracket Pnt Footrest STLT 145 156524 Rod Pivot Chassis/Hood 159 155123X428 Cupholder Stlt Black 166 171875 Screw Hwhd Hi-Lo #13-16 x 3/4 206 170165 Bolt Shoulder 5/16-18TT 207 17670508 Screw Thdrol 5/16-18 x 1/2 Tytt 208 17670608 ScrewThdrol 3/8-16 x 1/2 209 17000612 Screw Hexwsh Thdr 3/8-16 x 3/4 211 145212 Nut Hex Flange Lock 212 184248 Insert Lens Reflective 219 17000512 Screw 5/16-18 x 3/4 258 184245X599 Lens Laser RH 259 184246X599 Lens Laser LH 260 184250X428 Cover Lens Laser 261 184258X428 Insert Grille Laser - - 5479J Plug, Button NOTE: All component dimensions given in U. S. inches 1 inch = 25.4 mm 35
TRACTOR - MODEL NUMBER 917.272850 GROUND DRIVE 57 198 32 30 25 .162 / 166 156 5 6 35 t8 212 70 37 34 26 27 116 202 t50 36
TRACTOR -- MODEL NUMBER 917.272850 GROUND DRIVE KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. 1 Transaxle (See Breakdown) 64 71170764 Peerless 206-545C 65 STD551143 2 146682 Spring, Return, Brake 66 154778 3 123666X Pulley, Transaxle 70 134683 4 12000028 Ring, Retainer 74 137057 5 121520X Strap, Torque 75 121749X 6 17060512 Screw 5/16-18 x 3/4 76 STD581075 8 165866 Rod Shifter Fender STLT 77 123583X 10 STD561210 Pin, Cotter 78 121748X 11 105701X Washer, Shift Plate 79 STD580025 13 74550412 Bolt 1/4-28 UNF W/Patch Gr. 8 80 145090 14 10040400 Washer Lock Hvy Helical 81 165592 16 STD541431 Nut Lock Hx W/Ins 82 165711 5/16-18 x Gr.5 83 19171216 18 STD523710 Bolt Fin Hex 84 166231 3/8-16 Unc x 1 Gr. 5 85 150360 19 STD541437 Nut 89 158391X428 21 106933X Knob 90 124346X 22 130804 Rod, Brake 96 STD624003 24 STD541237 Nut 112 19091210 25 106888X Spring, Brake Rod 113 127285X 26 STD551037 Washer 116 72140608 27 STD561210 Pin 120 73900600 28 175765 Rod, Parking Brake 145 74490540 29 71673 Cap, Parking Brake 150 175456 30 169592 Bracket, Transaxle 151 19133210 32 STD523107 Bolt 156 166002 34 175578 Shaft Assembly, Foot Pedal 158 165589 35 120183X Bearing, Nylon 159 183900 36 STD551062 Washer 161 72140406 37 STD571810 Roll Pin 162 73680400 38 179114 Pulley, Composite, Flat 163 74780416 39 74760648 Bolt 164 19091010 41 175556 Keeper, Belt, Idler 165 165623 47 127783 Pulley, Idler, V-Groove, Plastic 166 166880 48 154407 BellcrankClutch Grnd Dry Stl 168 165492 49 123205X Retainer, Belt 169 165580 50 72110612 Bolt Carr. Sh 3/8-16 x 1-1/2 Gr. 5 170 178394 51 STD541437 Nut Crown Lock 3/8-16 Unc 197 169613 52 STD541431 Nut Crown Lock 5/16-18 Unc 198 169593 53 105710X Link, Clutch 202 72110614 55 105709X Spring, Clutch Return 212 145212 56 17060620 Screw 3/8-16 x 1-1/4 57 130801 V-Belt, Ground Drive 59 169691 Keeper, Belt, Center Span 61 17120614 Screw 3/8-16 x .875 62 8883R Cover, Pedal 63 175410 Pulley, Engine DESCRIPTION Bolt, Hex 7/16-20 x 4 Gr. 5 Washer Keeper, Belt, Engine, Fool Proof Guide, Mower Drive Belt, R.H. Spacer, Axle Washer 25/32 x 1-1/4 x 16 Ga. E-Ring Key, Square 2.0 x .1845/1865 Washer 25/32 x 1-5/8 x 16 Ga Key Woodruff Arm, Shift Shaft Asm Cross Tapered 650 20 Spring, Torsion Washer 17/32 x 3/4 x 16 Ga. Link Transaxle Nut, Nylock Console, Shift, STLT Nut, Self-Thding, Wsh Hd 1/4 Retainer Spring 1" Washer 9/32 x 3/4 x 10 Ga. Strap Torque 90 Degrees Bolt Rdhd Sqneck 3/8-16 x 1 Nut Lock Fig. 3/8-16 Unc Bolt, Hex Flghd 5/16-18 Gr. 5 Spacer Retainer Washer 13/32 x 2 x 10 Ga. Washer Srrted 5/161D x 1.125 Bracket Shift Mount Hub Tapered Flange Shift Lt Bolt Rdhd Sqnk 1/4-20 x 3/4 Gr.5 Nut Crownlock 1/4-20 Unc Bolt Hex Fin 1/4-20 Unc x 1 Gr. 5 Washer 5/8 x .281 x 10 Ga. Bracket Pivot Lever Screw 5/16-18 x 5/8 Bolt Shoulder 5/16-18 x .561 Plate Fastening Lt Keeper Belt Transaxle Gear Nyliner Snap-In 5/8 ID Washer Nyliner 7/8 tD x .105 Hd Bolt Carr. SH 3/8-16 x 1-3/4 Gr. 5 Nut Hex Flange Lock NOTE: All component dimensions given in U. S. inches 1 inch = 25.4 mm 37
TRACTOR -- MODEL NUMBER 917.272850 STEERING I / / _ I I----.-._ 1 n i "r'-'-'-'42 88 I 29 t3 65 68 67 67 68 4O 10 4,3 / l 38
TRACTOR -- MODEL NUMBER 917.272850 STEERING KEY PART NO. NO. DESCRIPTION 1 184704X428 Steering Wheel 2 172393 Axle Assembly 3 169840 Spindle Assembly, L.H. 4 169839 Spindle Assembly, R.H. 5 6266H Bearing, Race, Thrust, Hardened 6 121748X Washer 25/32 x 1-5/8 x 16 Ga. 8 12000029 Ring, Klip 10 175121 Draglink 11 STD551137 Washer, Lock 12 73940800 Nut Hex Jam Toplock 1/2-20 Unf 13 136518 Spacer Bearing Axle Front 15 145212 Nut, Hex Flange Lock 17 180641 Shaft Assembly, Steering 26 126847X Bushing, Link, Drag 28 19131416 Washer 13/32 x 7/8 x 16 Ga. 29 17060612 Screw 3/8-16 x 3/4 30 STD561210 Pin Cotter 32 130465 Red, Tie 36 155099 Bushing, Steering 37 152927 Screw 38 159946X428 Insert, Steering Wheel 39 19182411 Washer 9/16 ID x 1-1/20D 11 Ga. 40 STD541537 Nut Lock Center 3/8-24 Unf 41 159945 Adaptor, Steering Wheel 42 145054X428 Boot, Steering Shaft 43 121749X Washer 25/32 x 1-1/4 x 16 Ga. 44 180640 Extension Shaft Steering 46 184946X428 Cap, Spindle 51 73540400 Nut Crownlock 1/4-28 54 71130420 Belt Hex 1/4-28 UNF x 1-1/4 Gr. 8 65 160367 Spacer Brace Axle 67 72140618 Belt BDHD Sqnk 3/8-16 x 2-1/4 68 169827 Axle, Brace 71 175146 Steering Asm. 82 169835 Bracket Susp. Chassis Front 87 173966 Washer Flat .781 x 1-1/2 x .14 88 175118 Belt Shoulder 7/16-20 Unc 91 175553 Clip Steering NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 39
TRACTOR -- MODEL NUMBER 917.272850 ENGINE _26 31 39 14 38 13 29 \ OPTIONAL EQUIPMENT Spark Arrester 23 J 4O
TRACTOR -- MODEL NUMBER 917.272850 ENGINE KEY PART NO, NO. DESCRIPTION 1 170546X505 Control, Throttle Paddle 2 17720408 Screw, Hex Thd Cut 1/4-20 x 1/2 3 Engine, B&S, (See Breakdown) No. 407777-0174-E1 4 149723 Muffler Exhaust 5 159955 Exhaust Asm. Left 6 160589 Exhaust Asm. Right 8 171877 Bolt 5/16-18unc x 3/4 W/Sems 10 162797 Heat Shield Lt 13 165391 Gasket, Muffler 14 148456 Tube Drain Oil Easy 16 STD551237 Washer Lock Ext Tooth 3/8 17 17060624 Screw 3/8-16 x 1-1/2 23 169837 Shield, Brn/Dbr Guard 25 145996X505 Control Choke 26 73920600 Nut Keps 3/8-24 Unf 29 137180 Arrestor, Spark 31 157103 Tank, Fuel 32 161696 Cap Fuel Guage 33 123487X Clamp, Hose 34 106082X Spacer Pad 37 8543R Line, Fuel 38 181654 Plug, Oil Drain Easy 39 109227X Pad Idler 45 17000612 Screw Hex Wsh3/8-16 x 3/4 72 183906 Screw Socket Head 5/16-18 x 1 81 73510400 Nut Keps Hex 1/4-20 Starter Nut NOTE: All component dimensions given in U. S. inches 1 inch = 25.4 mm 41
TRACTOR -- MODEL NUMBER 917.272850 SEAT ASSEMBLY \ \ \\\\ I I I 11 12 KEY PART NO. NO. 1 180597 2 180166 3 71110616 4 19131610 5 145006 6 STD541437 7 124181X 8 17000616 9 19131614 10 180186 11 166369 DESCRIPTION Seat Bracket Pnt Pivot Seat (blk) Bolt Fin Hex 3/8-16unc X 1 Washer 13/32 X 3/4 X 10 Ga Clip Push In Hinged Nut Hex Lock w/Ins 3/8-16 Uric Spring Seat Cprsn 2 250 BIk Zi Screw 3/8-16 X 1 Washer 13/32 X 1 X 14 Ga Pan Pnt Seat (blk) Knob Seat Adj Wingnut _J J j I z_ _ r _ 22 21 '\ KEY PART NO. NO. DESCRIPTION 12 121246X 13 121248X 14 72050412 15 134300 16 121250X 17 123976X 21 171852 22 STD541431 24 19171912 Bracket Pnt Mounting Switch Bushing Snap BIk Nyl 50 Id Bolt Rdhd Sht Nk 1/4-20x1-1/2 Spacer Split 28 X 96 Zinc Spring Cprsn 1 27 BIk Pnt Nut Lock 1/4 Lge Fig Gr 5 Zinc Bolt Shoulder 5/16-18 Unc-2A Nut Hex Lock w/Ins 5/16-18 Washer 17/32 X 1-3/16 X12Ga. NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 42
TRACTOR -- MODEL NUMBER 917.272850 DECALS 18 2 7 7 14 19 _, . 21 15 13 KEY PART NO. NO. 1 186368 2 186437 3 186280 4 186281 5 138047 6 133644 7 186869 8 172331 9 186282 10 156439 11 186283 12 172258 8 KEY PART DESCRIPTION NO. NO. Decal, Oper. Instr. 13 146046 Decal, Replacement 14 179128 Decal, Hood, R.H. 15 160396 Decal, Hood, L.H. 16 184842 Decal, Battery 17 184843 Decal, Customer Maintenance 18 164065 Decal, Chassis 19 149516 Decal, Mower Srs - - 138311 Decal, Fender, Craftsman - - 165800X428 Decal, Fender Danger - - 165799X428 Decal, Hood Side - - 184950 Decal, HP Engine - - 184951 DESCRIPTION Decal, V-Belt Drive Schematic Decal, Deck B 42" Decal, V-Belt Schematic Decal, Grille RH Decal, Grille LH Decal, Strg. Whl Decal, Battery Dngr/Psn Eng Decal, Lift Handle Pad Footrest LH STLT Pad Footrest RH STLT Owner's Manual, English Owner's Manual, Spanish WHEELS AND TIRES 7 4,10 11 KEY PART NO. NO. 1 59192 2 65139 3 106222X 4 59904 5 106732X624 6 278H 7 9040H 8 106108X624 9 122082X 10 7152J 11 104757X428 -- 144334 DESCRIPTION Cap Value Tire Stem Value Tire FTs 15 X 6 0 - 6 Service Tube Inner Front #35060 Rim Asm 6"front White Service Fitting Grease Bearing Flange Rim Asm 8"rear White Service Tire R Ts 20 X 10-8 Service Tube Rear 9 5 X 8 Service Cap Axle BIk 1 50 X 1 00 Sealant, Tire (10 oz. tube) NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 43
TRACTOR -- MODEL NUMBER 917.272850 LIFT ASSEMBLY 7 13 12 6 3 2 6 5 19 13 32 32 / 19 13 2O 15 20 44
TRACTOR -- MODEL NUMBER 917.272850 LIFT ASSEMBLY KEY PART NO. NO. DESCRIPTION 1 159460 Washer Asm Inner Spring W/Plunger 2 159471 Shaft Asm. Lift 3 105767X Pin Groove 4 12000002 E Ring #5133-62 5 19211621 Washer21/32x1 x21 Ga. 6 120183X Bearing Nylong 7 125631X Grip Handle Fluted 8 122365X Button Plunger Read 11 139865 Link Asm Lift L.H. 12 139866 Link Asm Lift R.H. 13 STD624008 Retainer Spring 15 173288 Link Front 16 73350800 Nut Jam Hex 1/2-13 Unc 17 175689 Trunnion BIk Zinc 18 73800800 Nut Lock w/Wsh 1/2-13 Unc 19 139868 Arm Suspension Mower 20 163552 Retainer Spring 31 169865 Bearing, Pvt. Lift 32 73540600 Nut Crownlock 3/8-24 NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 45
TRACTOR -- MODEL NUMBER 917.272850 MOWER DECK 68 34 i- !147 .__ 105 106 _'_ 102 lu_ ! loa'_ 1 1 6 101 102/_ 117 _ 119 118 F 19F 21 10_ 9_ 21 23 24 _112 _117 42 D man-t-path stlt 3. 46
TRACTOR -- MODEL NUMBER 917.272850 MOWER DECK KEY PART KEY PART NO. NO. DESCRIPTION NO. NO, 1 165892 Mower Deck Assembly, 42" 59 141043 2 STD533107 Bolt 67 184939 3 138017 Bracket Assembly, Sway Bar, 68 144959 Front 92 STD541437 4 165460 Bracket Sway Bar 38/42" Deck 101 136420 5 STD624008 Retainer Spring 102 71081010 6 178024 Bar Sway Deck 103 19061216 8 850857 Bolt, Hex 3/8-24x1.25Gr. 8 104 STD551110 9 STD551137 Washer, Lock 105 160793 10 140296 Washer, Hardened 106 2029J (The following blades are 111 179292 available) 112 179293 11 134149 Blade, 42" MulchingStd (For 113 17060510 mulching mowers only) 114 73510500 -- 139775 Blade, 42" Mulching Premium 116 4898H (For better wear when mulching) 117 165746 - - 138971 Blade, 42" Hi-Lift (For bagging or 118 73930600 discharing) 119 19121414 13 137645 Shaft Assembly, Mandrel, Vented 129 19131312 14 128774 Housing, Mandrel, Vented 130 STD523710 15 110485X Bearing, Ball, Mandrel 131 STD533710 16 174493 Stripper, Vented Mower Deck 142 165890 18 72140505 Bolt, Carriage 5/16-18 x 5/8 143 157109 19 132827 Bolt, Shoulder 144 158634 20 159770 Baffle, Vortex 145 165888 21 STD541431 Nut Crownlock 5/16-18 UNC 146 171977 23 177563 Bracket, Deflector 147 131335 24 105304X Cap, Sleeve 148 169022 25 123713X Spring, Torsion, Deflector 149 165898 26 110452X Nut, Push 150 19091216 27 130968X428 Shield, Deflector 151 169670 28 19111016 Washer 11/32x5/Sx16Ga. 152 169676 29 131491 Rod, Hinge 153 169674 30 173984 Screw Thdrol Washer Head 154 169675 31 129963 Washer, Spacer 155 169671 32 153535 Pulley, Mandrel 156 169672 33 178342 Nut, Toplock, Flanged 157 169669 34 STD533717 Bolt 158 17720408 36 131494 Pulley, Idler, Flat 159 72140614 37 STD551037 Washer 13/32 x 13/16 x 16Ga. 184 19131410 40 STD541437 Nut Crownlock 3/8-16 UNC - - 130794 44 140088 Guard, Mandrel, L.H. 45 STD624003 Retainer 46 137729 Screw, Thd. Roll 1/4-20 x 5/8 - - 169583 48 133944 Washer, Hardened 52 139888 Bolt, Shoulder 5/16-18 UNC 53 184907 Arm Assembly, Pad, Brake 54 178515 Washer, Hardened 55 155046 Arm, Idler 56 165723 Spacer, Retainer DESCRIPTION Guard, TUV Idler Knob Custom Oval V-Belt Nut Mulcher Cover Screw Washer #10 Washer, Lock Latch Assembly, Bagger Nut, Weld Bracket Gauge Wheel Lh Bracket Gauge Wheel Rh Screw 5/16-18 Uric Nut Keps 5/16-18 Uric Bolt Shoulder Wheel Gauge Std Nut Cenferlock 3/8-16 Uric Washer 3/8 x 7/8 x 4 Ga. Washer 13/32 x 13/16 x 12Ga. Bolt, Fin Hex 3/8-16 Unc x 1 Gr. 5 Bolt, Rdhd Sqnk 3/8-16UN0 xl Arm Spring Brake Mower Bracket Arm Idler 42" Keeper Belt 42" Clutch Cable Pulley Idler Flat Bolt Carriage Idler Spring Extension Spring Return Idler Retainer Spring Yellow Zinc Washer 9/32 x 3/4 x 16 Ga. Bracket Clutch Cable Clutch 42 tn Washer Flat 3/8" Type B Spring Retainer Spring Retention Lever Spacer Rod Clutch Screw Hex Thd Cut 1/4-20 x 1/2 Bolt Rdhd Sqn 3/8-16 Uric x 3/4 Washer 13/32 x 7/8 x 10 Ga. Mandrel Assembly (Includes Hou- sing, Shaft and Shaft Hardware Only - Pulley Not Included) Replacement Mower, Complete NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 47
TRACTOR -- MODEL NUMBER 917.272850 PEERLESS TRANSAXLE--MODEL NUMBER 206-545C 35A 8 157 47 _ _4'31A 15 18 4 / 34 79 48
TRACTOR -- MODEL NUMBER 917.272850 PEERLESS TRANSAXLE--MODEL NUMBER 206-545C KEY PART KEY PART NO. NO. DESCRIPTION NO. NO, DESCRIPTION 1 772147 Transaxle Cover 39 786026 Dowel Pin 2 780086A Needle Bearing 5/8" 40 792076A Flat Washer 3 770128 Transaxle Case .312 ID x .059W 4 776395 Countershaft 41A 790079 Brake Lever 5 776409 Output Shaft 42 792073A Screw 1/4 - 20 x 1-1/4" 6 778364 Spur Gear (38 teeth) 42A 792085A Screw 1/4 - 20 x 2 1/4" 6A 778369 Spur Gear (15 teeth) 43 792075 Locknut 5 / 16 - 24 7 778330 Spur Gear (11 teeth) 44 790025 Brake Pad Holder 8 792180 Shift Key 45 786066 Spacer .2625 x 1.0 8A 792047 Woodruff Key #9 46 786086 Brake Lever Bracket 9 784352 Shift Collar 47 774690 Axle (11-15 / 16" Long) 10 784378 Shift Rod & Fork 48 774691 Axle (16 - 1 / 2" long) 11 778334 Bevel Gear (30 teeth) 49 778356 Spur Gear (29 teeth) 12 778309 Input Bevel Pinion (13 teeth) 50 778338 Spur Gear (27 teeth) 13 778368 Bevel Gear (13 teeth) 51 778354 Spur Gear (23 teeth) (Include. 14) 52 778352 Spur Gear (19 teeth) 14 778368 Bevel Pinion (13 teeth) 53 778350 Spur Gear (16 teeth) (Include. 13) 54 778346 Spur Gear (15 teeth) 15 778370 Ring Gear (43 teeth) 56 778355 Spur Gear (11 teeth) 17 786188 Drive Pin 57 778337 Spur Gear (13 teeth) 18 786102 Spacer 1.130 X .695 58 778353 Spur Gear (17 teeth) 20 792077A Ball 5/16" dia 59 778351 Spur Gear (21 teeth) 21 792078 Set Screw 3/8 - 16 x 3/8" 60 778349 Spur Gear (24 teeth) 22 792079 Spring .310 OD x .625 L 61 778345 Spur Gear (25 teeth) 25 792073A Screw 1/4 - 20 x 1-1/4" 65 780189 Flat Washer 25A 792177 Screw 1/4-20 x 1-3/8" .563 ID x .062W 26 792125 Retaining Ring (pkg of 2) 66 776422 Input Shaft 27 792035 Retaining Ring 67 776396 Shifter & Brake Shaft 28 788040 Retaining Ring 69 792170 Retaining Ring 29 780072 Thrust Washer 70 786187 Spacer .890 .627 ID x .031W 71 788069 Square Cut Ring 29A 780160 Thrust Washer 71B 788092 "O"Ring .762 ID x .031W 76 780090 Flat Washer 29B 780051 Thrust Washer 1.128 ID x .058W .762 ID x .031W 77 788078A Inverted Retaining Ring 29C 780199 AntFRotation Washer .632 79 792144 Spring .430 OD x .5000 L 30 780108 Cup Washer 82 778333 Bevel & Spur Gear (30 & 13 1.127 I D x .032W teeth) 31 780001 Flat Washer .750 ID x .056W 83 778338 Spur Gear (27 teeth) (Use As Needed) 85 792154 Oil Fill Plug 31A 780195 Flat Washer 87 788089A Oil Seal 9 / 16" .750 ID x .062W 150 788093A Liquid Gasket RTV Silicone 32 788083 Oil Seal 5/8" 157 788088A Oil Seal 3/4" 34 780194 Bushing .563 180 730229A Gear Oil 80W90 35 780193 Flanged Bushing 5 / 8" ID 900 794712 Replacement MST 35A 780197 Flanged Bushing .751 206-545CTransaxle 36 790075 Brake Disk 37 790007 Brake Pad Plate NOTE: All component dimensions given in U.S 38 799021 Brake Pad (pkg of 2) inches 1 inch = 25.4 mm 49
TRACTOR -- MODEL NUMBER 917.272850 BRIGGS & STRATTON ENGINE-MODEL NUMBER 407777, TYPE NUMBER 0174-E1 216 188 222 265 [_ 267 718 1019 LABEL KIT 25J 27 G 220 @ 750 1017_ 24 [_ I 1058 OWNER'S MANUAL 1036 EMiSSiON LABEL 447A_ 305 447A 445 967 447 50J 163 54_ l_ 654 @ 1027 D 53 1 1095 VALVE GASKET SET 276 @ 7 883 d 868 163_ 1022_ 50
TRACTOR -- MODEL NUMBER 917.272850 BRIGGS & STRATTON ENGINE-MODEL NUMBER 407777, TYPE NUMBER 0174-E1 35 36 _ 1022 1029 22 o 240_ 385_ _788 _ 121 CARBURETOR OVERHAUL KIT 51 _ 276 @ 987 104 672 _ 105 1123 @ 117 _ 1124 137 @ 552 552A 742 @ 404 552A 691 977CARBURETOR GASKET SET 633 51 987 e 137 672_ 150 _ 1123_ 276 @ 1124 '_ 211 209 _ 562 914_ 108 _,_" _,, 6.33 975_137( _ 1123 _ _ 160_ 1127 117 _ 276 @ 118 _' 51
TRACTOR -- MODEL NUMBER 917.272850 BRIGGS & STRATTON ENGINE-MODEL NUMBER 407777, TYPE NUMBER 0174-E1 74_ 668 474 332 ® It 75 @ 1119 695 _' 358 ENGINE GASKET KIT 3_ 12 2O 868 943 @ 51 _ 1022842 163 276 @ 691 883 _ 783_ I'°_ I 697 52
TRACTOR -- MODEL NUMBER 917.272850 BRIGGS & STRATTON ENGINE-MODEL NUMBER 407777, TYPE NUMBER 0174-E1 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 690231 Cylinder Assembly 118 690989 Jet-Main (High Altitude) 2 499585 Kit-Bushing/Seal (Magneto Side) 121 499811 Kit-Carburetor Overhaul 3 391086 • Seal-Oil (Magneto Side) 125 499804 Carburetor 4 690069 Sump-Engine 130 690993 Valve-Throttle 5 693998 Head-Cylinder (Cylinder 1) 131 499805 Kit-Throttle Shaft 5A 693999 Head-Cylinder (Cylinder 2) 133 499806 Float-Carburetor 7 690962 , Gasket-Cylinder Head 135 499803 Tube-Fuel Transfer 8 499601 Breather Assembly 137 690994 O_ Gasket-FIoatBowl 9 690937 • Gasket-Breather 141 499807 Kit-Choke Shaft 10 690960 Screw (Breather Assembly) 142 499808 Q Nozzle-Carburetor 11 690942 Tube-Breather 146 690979 Key-Timing 12 697227 • Gasket-Crankcase 150 690995 O_ Gasket-Nozzle 13 690360 Screw (Cylinder Head) 160 690996 Retainer-Solenoid 15 690946 Plug-Oil Drain 163 691001 , Gasket-Air Cleaner 16 691046 Crankshaft 165 693148 Nut (Ring Gear) 20 690947 • Seal-Oil (PTO Side) 187 691050 Line-Fuel (Cut to Required 22 694966 Screw (Engine Sump) Length) 23 691054 Flywheel 187A 691049 Line-Fuel(Molded) 24 222698 Key-Flywheel 188 690960 Screw (Control Bracket) 25 499588 Piston Assembly (Standard) 192 690083 Adjuster-Rocker Arm 25 499589 Piston Assembly (.010" Over- 209 697674 Spring-Governor size) 211 691019 Spring-Governed Idle 25 499590 Piston Assembly (.020" Over- 212 695238 Link-Throttle size) 213 691021 Bracket-Choke Control 25 499591 Piston Assembly (.030" Over- 216 691022 Link-Choke size) 219 696376 Gear-Governor 26 499604 Ring Set-Piston (Standard) 220 690412 Washer (Governor Lever) 26 499605 Ring Set-Piston (.010" Oversize) 222 691023 Bracket-Control 26 499606 Ring Set-Piston (.020" Oversize) 227 691048 Lever-Governor Control 26 499607 Ring Set-Piston (.030" Oversize) 231 690718 Screw (Choke Valve) 27 690975 Lock-Piston Pin 240 691035 Filter-Fuel 28 690229 Pin-Piston 250 690957 Retainer-Breather 29 499583 Rod-Connecting 252 690956 Collector-Oil 32 690976 Screw (Connecting Rod) 265 691024 Clamp-Casing 33 499596 Valve-Exhaust 267 695134 Screw (Casing Clamp) 34 499597 Valve-Intake 276 690997 °Q Washer-Sealing 35 690963 Spring-Valve (Intake) 287 690960 Screw (Dipstick Tube) 36 690963 Spring-Valve (Exhaust) 304 695277 Housing-Blower 40 690964 Retainer-Valve 305 691005 Screw (Blower Housing) 42 499586 Keeper-Valve 309 691262 Motor-Starter 45 690977 Tappet-Valve 310 691263 Bolt-Starter Motor 46 690978 Camshaft 311 497608 Brush Set 48 692714 Short Block (446777-0027-E2 332 691059 Nut (Flywheel) Replacement Engine) 333 691060 Armature-Magneto 50 695241 Manifold-Intake 334 691061 Screw (Magneto Armature) 51 690950 °Q_: Gasket-Intake 337 691043 SparkPlug 53 690951 Stud (Carburetor) 358 694012 Set-Engine Gasket 54 695240 Screw (Intake Manifold) 363 691062 Flywheel Puller 73 691055 Screen-Rotating 383 690966 Wrench-Spark Plug 74 691057 Screw (Rotating Screen) 385 690960 Screw (Fuel Pump) 75 691056 Washer (Flywheel) RPM Settings:Low Speed: 1900-2100 89 690283 Plug-Oil High Speed: 3000-3200 95 690718 Screw (Throttle Valve) 98 499802 Kit-Idle Speed ° Included in Engine Gasket Set, Key. No. 358 104 690984 Q Pin-Float Hinge O Included in Carburetor Overhaul Kit, Key. No. 105 690985 Q Valve-Float Needle 121 108 690986 Valve-Choke :l: Included in Carburetor Gasket Set, Key. No. 117 690232 Q Jet-Main (Standard) 977 Included in Valve Gasket Set, Key. No. 1095 NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 53
TRACTOR -- MODEL NUMBER 917.272850 BRIGGS & STRATTON ENGINE-MODEL NUMBER 407777, TYPE NUMBER 0174-E1 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 387 808656 Pump-Fuel 865A 691014 Cover-Air Guide 404 690442 Washer (Governor Crank) 865B 691015 Cover-Air Guide 405 690960 Screw (Back Plate) 868 690968 o Seal-Valve 418 690999 Plate-Carburetor 914 691127 Screw (Rocker Cover) 445 499486 Filter-Air Cleaner Cartridge 918 694000 Hose-Vacuum 447 691003 Screw (Air Guide Cover) 929 695239 Screw (Choke Control Bracket) 447A 690960 Screw (Air Guide Cover) 929A 691003 Screw (Choke Control Bracket) 467 691008 Knob-Air Cleaner 943 690589 • SeaI-O Ring (Oil Pump Cover) 474 696459 Alternator 947 499809 Solenoid-Fuel 505 691029 Nut (Governor Control Lever) 965 499613 Cover-Oil Pump 510 497606 Drive-Starter 967 272638 Filter-Pre Cleaner 513 692024 Clutch-Drive 968 499788 Cover-Air Cleaner 523 691036 Dipstick 975 499810 Bowl-Float 524 691032 • Seal-Dipstick Tube 977 499812 Gasket Set-Carburetor 525 691037 Tube-Dipstick 987 691000 O$ Seal-Throttle Shaft 544 Armature-Starter (Service with 1005 499603 Fan-Flywheel 691262 Starter Motor) 1013 690954 Nipple-Oil Filter 552 690552 Bushing-Governor Crank 1017 690770 Screen-Oil Pump 552A 690553 Bushing-Governor Crank 1019 690103 Kit-Label 562 690311 Bolt (Governor Control Lever) 1022 690971 o Gasket-Rocker Cover 573 691009 Plate-Back 1023 499599 Cover-Rocker (Cylinder 1) 601 691038 Clamp-Hose 1023A499600 Cover-Rocker (Cylinder 2) 615 690317 Retainer-Governor Shaft 1024 499054 Pump-Oil 616 691045 Crank-Governor 1026 690981 Rod-Push (Steel) 617 691917 SeaI-O Ring (Intake Manifold) 1026A690982 Rod-Push (Aluminum) 628 690960 Screw (Fuel Pump Bracket) 1027 492932 Filter-Oil 633 690998 Q_: Seal-Choke/Throttle Shaft 1029 690972 Arm-Rocker 635 66538 Boot-Sparkplug 1035 691042 Shaft-Pump 654 690958 Nut (Carburetor) 1036 695704 Label-Emission 668 691215 Spacer 1051 691265 Ring-Retaining 672 690234 Q_: Gasket-Carburetor Plate 1058 274794 Owner's Manual 691 690657 • Seal-Governor Shaft 1070 691674 Screw (Flywheel Fan) 695 693149 Screw (Ring Gear) 1090 691293 Retainer-Brush 697 690372 Screw (Drive Cap) 1095 694013 Kit-Valve Overhaul 703 691010 Clip 1100 690973 Pivot-Rocker Arm 718 690959 Pin-Locating 1119 691183 Screw(Alternator) 726 499612 Gear-Ring 1123 690987 O$ SeaI-O Ring (Solenoid Retainer) 741 690980 Gear-Timing 1124 690988 O$ SeaI-O Ring (FueITransferTube) 742 690328 Retainer-E Ring 1126 690991 Screw (Fuel Transfer Tube) 750 696999 Screw (Oil Pump Cover) 1127 690992 Screw (Float Bowl) 783 693058 Gear-Pinion 1128 690990 Q Screw (Carburetor Nezzle) 788 691039 Bracket-Fuel Pump 1169 693140 Screw (Carburetor Cover Plate) 789 695050 Harness-Wiring RPM Settings:Low Speed: 1900-2100 797 691029 Nut (Brush Retainer) High Speed: 3000-3200 797A 693167 Nut (Brush Retainer) 798 690967 Screw (Rocker Arm) o Included in Engine Gasket Set, Key. No. 358 801 691283 Cap-Drive O Included in Carburetor Overhaul Kit, Key. No. 802 691286 Cap-End 121 803 Housing-Starter (Service with :l: Included in Carburetor Gasket Set, Key. No. 691262 Starter Motor) 977 842 691031 • Seal-Dipstick!Tube Included in Valve Gasket Set, Key. No. 1095 847 499602 Dipstick/Tube Assembly 851 493880 TerminaI-Sparkplug NOTE: All component dimensions given in U.S. inches 855 691011 Adapter-Air 1 inch = 25.4 mm 865 691012 Cover-Air Guide 54
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION o'l o'l WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees. Make turns gradually to prevent tipping or loss of control. Exercise extreme caution when changing direction on slopes. 1. Fold this page along dotted line indicated above. 2. Hold page before you so that its left edge is vertically parallel to a tree trunk or other upright structure. 3. Sight across the fold in the direction of hill slope you want to measure. 4. Compare the angle of the fold with the slope of the hill.
Your Home For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters. 1-800-4-MY-HOME ® Anytime, day or night (1-800-469-4663) (U.S.A. and Canada) www.sears.com www.sears.ca Our Home For repair of carry-in products like vacuums, lawn equipment, and electronics, call or go on-line for the nearest Sears Parts and Repair Center. 1-800-488-1222 Anytime, day or night (U.S.A. only) www.sears.com To purchase a protection agreement (U.S.A.) or maintenance agreement (Canada) on a product serviced by Sears: 1-800-361-6665 (Canada) Au Canada pour service en fran_,ais: 1-800-LE-FOYER Mc (1-800-_7) www.sears.ca SEARS © Sea_, Roebuck ar_ Co. ® Registered Trademark / TM Trademark / SM Service Mark of Sears, Roebuck and Co. ® Marca Registrada / TM Marca de F_brica / SM Marca de Servicio de Sears, Roebuck and Co. MC Marque de commerce / MD Marque d_pos_e de Sears, Roebuck and Co. 184950 Rev. 4 05.23.03 TR/MH/TR Printed in U.S.A.