Craftsman SECURITY+ 139.53682 Owner's Manual
CRRFTSMRN ® OWNER'S MANUAL Children operating or playing with s garage door opener can injure themselves or others. The garage door could close and cause serious injury or death. Install the receiver (or any additional push buttons) out of the reach of children and away from all moving parts of the door and door hardware, but where the garage door is visible. Do not allow children to operate the push button(s) or the remote control(s). A moving garage door could injure someone under it. Activate the opener only when the door is properly adjusted, you can see it clearly, and there are no obstructions to door travel⢠DISCONNECT POWER TO THE GARAGE DOOR OPENER REFOREPROCEEDING. The SECURITY Universal Remote Control Conversion Kit consists of a receiver and remote control(s). This accessory will convert almost any garage door opener to rolling code technology. The remote control sends a coded signal from outside the garage. Inside the garage, the plug-in receiver accepts the transmitted signal and starts the door opener. With Security , the code between the remote control and the receiver changes with each use, accessing over 100 billion new codes. IMPORTANT: To improve the security of your opener, discard your old remote controls end erase or reset your code. For maximum security and range, you must disable the existing receiver on your opener, otherwise it could still activate your opener: ⢠If there is an external receiver, disconnect power to it. ⢠If it is an integrated receiver, either clip off the component that feeds power to the receiver or remove the tuning slug and antenna from the receiver section. If you have a different brand of opener, contact the manufacturer for additional information on disabling the existing receiver. ⢠If you have a Sears opener with an SRT receiver, erase the old codes by holding down the SRT button for 6 seconds until the indicator light turns off. ⢠If you have code switches, reset them to a random code and deactivate the receiver as follows: On the opener panel, peel back the lower right _ I_ I_ corner of the label to expose the tuning slug (closest to the antenna), as shown. Remove the slug with a small hex head wrench and cut the antenna wire. Cut Antenna Tuning -- Slug .Peal beck label at comet SECURITY,F Universal Remote Control Conversion Kit Model 139.53682 (With I Remote Control) Model 139.53683 (With 2 Remote Controls) To comply with Fco rules, adjustments or modifications of thr= reseivor and,/or transmitter are prohibited, except for changing the code set_g o_ replacing the ransmittor battery. THERE ARE NO USER SERV CEABLE PARTS. NOTICE TO U. S. CONSUMERS: Some stat_s prohibit the service or repair of garage door openers wbch cannot be made to comply with the safety standards contained in UL 325 (1988 revision). In order to comply with both the letter and the spirit of these laws, this universal remote conttol converter kit should not be used with any Sears Craftsman = garage door opener manufactured pdor to Apdl 1, 1982. Power.. Aotuator Cover Indicator Light SRT ._ Indicator ght I Antenna !Terminals "o _11 Wire - I llico.. - _ act Bell Wire L._ to Garage Door ⢠"_-- Opener Terminals SRT (learn) Actuator Belllwira OPEN RECEIVER: Insert a small screwdriver in slot on receiver front panel as shown⢠Twist up actuator cover. CONNECT RECEIVER AND OPENER: Remove about 1/4" of insulation from each end of the 2-strand bell wire. Connect one end to the receiver screw terminals (polarity is NOT required). Route wire along the channels and out the bottom as shown. Connect the other end of the bell wire to the two opener terminal screws labeled "2" (white) and "1" (red), "common" and "command" or the terminals used for the push button control. Use insulated staples (not supplied) to secure bell wire between receiver and opener. Length of bell wire depends on where the receiver will be installed. Replace the actuator cover. Choose a 120Vac polarized outlet for the receiver which is OUT OF THE REACH OF CHILDREN. Plug receiver into selected outlet. Return power to the opener. Side two contains code setting instructions and service information,
PROGRAMMING THE RECEIVER The receiver and remote control(s) have been factory preset with a matching code. The door will open when you press the LARGE push button. You can activate your opener with up to eight SECURITY.I. remote controls (with blue push buttons) and one SECURITY Keylees Entry. If you purchase additional remote controls to operate this receiver: 1. Remove the receiver actuator cover. 2. Press and HOLD the selected remote control push button (Illustration A). 3. Then press the SRT (learn) actuator on the receiver (Illustration B). The adjacent indicator light will FLASH. Release the remote control push button. The opener will now operate when either the receiver actuator or the remote control push button is pressed. NOTE: If the remote control push button is not held down until the receiver Indicator light flashes, the receiver will not learn the code. To erase ALL remote control codes from memory: Press and HOLD receiver SRT actuator. Indicator light alongside will glow. When the Indicator light turns OFF (in about 6 seconds) ALL codes will be erased. 3-Function Remote Control A Select a remote control push button to operate receiver UnlversalReceiver B o SRT (loam) Actuator / Light THE REMOTE CONTROL BATTERIES Open this end first to avoid/_L--'_"_ cracking _sf_._-_<:_._--,"/ housin_ _:_ ⢠Twist to open The lithium batteries should produce power for up to 5 years. Replace batteries positive side down, as follows: Use the visor clip or screwdriver blade to pry open the case as shown. To replace the cover, insert the 3 tabs at the opposite end and snap shut. REPLACEMENT PARTS Universal Receiver (complete) .................... 41.6,5041-1 Receiver Actuator Cover .......................... 41A4926 Remote Control Housing Only (no circuit board) ....... 41A5032 Visor clip ...................................... 29B134 3V 2032 Lithium Battery ............................ 10A20 (1 required for Remote Model 139.53681B) 3V 2016 Lithium Battery ............................ 10A19 (2 required for Remote Model 139.53681) When ordering parts, always provide the following information: ⢠Product Type ⢠Model Number ⢠Part Number ⢠Part Description For the repair or replacement parts you need Call 7 am - 7 pm, 7 days s week 1-800-366-PART (1-800-366-7278) © 1997, Sears Roebuck and Company 114A2125C All Rights Reserved Pdnted in Mexico
PROGRAMMING THE RECEIVER The receiver and remote control(s) have been factory preset with a matching code. The door will open when you press the LARGE push button. You can activate your opener with up to eight SECURITY.I. remote controls (with blue push buttons) and one SECURITY Keylees Entry. If you purchase additional remote controls to operate this receiver: 1. Remove the receiver actuator cover. 2. Press and HOLD the selected remote control push button (Illustration A). 3. Then press the SRT (learn) actuator on the receiver (Illustration B). The adjacent indicator light will FLASH. Release the remote control push button. The opener will now operate when either the receiver actuator or the remote control push button is pressed. NOTE: If the remote control push button is not held down until the receiver Indicator light flashes, the receiver will not learn the code. To erase ALL remote control codes from memory: Press and HOLD receiver SRT actuator. Indicator light alongside will glow. When the Indicator light turns OFF (in about 6 seconds) ALL codes will be erased. 3-Function Remote Control A Select a remote control push button to operate receiver UnlversalReceiver B o SRT (loam) Actuator / Light THE REMOTE CONTROL BATTERIES Open this end first to avoid/_L--'_"_ cracking _sf_._-_<:_._--,"/ housin_ _:_ ⢠Twist to open The lithium batteries should produce power for up to 5 years. Replace batteries positive side down, as follows: Use the visor clip or screwdriver blade to pry open the case as shown. To replace the cover, insert the 3 tabs at the opposite end and snap shut. REPLACEMENT PARTS Universal Receiver (complete) .................... 41.6,5041-1 Receiver Actuator Cover .......................... 41A4926 Remote Control Housing Only (no circuit board) ....... 41A5032 Visor clip ...................................... 29B134 3V 2032 Lithium Battery ............................ 10A20 (1 required for Remote Model 139.53681B) 3V 2016 Lithium Battery ............................ 10A19 (2 required for Remote Model 139.53681) When ordering parts, always provide the following information: ⢠Product Type ⢠Model Number ⢠Part Number ⢠Part Description For the repair or replacement parts you need Call 7 am - 7 pm, 7 days s week 1-800-366-PART (1-800-366-7278) © 1997, Sears Roebuck and Company 114A2125C All Rights Reserved Pdnted in Mexico