HP 3COM Etherlink III 3C590 PCI 10BT Installation Manual
3COM Etherlink III 3C590 PCI 10BT Network Adapter Installation Guide
Notice The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by Hewlett-Packard. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of Hewlett-Packard Company. Microsoft®, Windows® and MS-DOS® are registered trademarks of Microsoft Corporation. MMX TM is a trademark of Intel Corporation. Pentium® is a registered trademark of Intel Corporation. Hewlett-Packard France Commercial Desktop Computing Division 38053 Grenoble Cedex 9 France ©1999 Hewlett Packard Company
General information to read before installing General information to read before installing On all systems : b efore installing LAN card, go into Bios setup and set PnP OS field to NO. ⢠How to change LAN card configuration if needed (Advanced users only) This is a general advisory on how to forcibly modify resources for ISA and PCI network cards. ISA cards: ⢠For ISA network adapters, start the configuration tool provided in driver kit (See install documentation) ⢠Under CMOS setup, go to Advanced > PnP/PCI ISA IRQ Resource Exclu- sion > reserve an IRQ for the adapter. PCI cards: ⢠For PCI network adapters, go to CMOS setup > Advanced > PnP/PCI ISA IRQ Resource Exclusion > reserve the IRQ for Legacy ISA. ⢠ISA cards canât use IRQ9 ⢠IRQ 9 is reported as being used by ACPI during POST. This is due to ISAâs inability to share IRQs. ⢠Using a different IRQ (e.g. 5, 7, 10, and 11) will work. For this: 1 Install the NIC then power up the system. 2 Press F2 to go to CMOS setup. 3 Set PnP OS to NO and reserve IRQ 5, 7, 10, or 11 (explained in installation section) 4 Save the configuration settings and boot to the applicable OS. 5 Follow installation steps. Sound conflict under Win 95 on VLi8 only ⢠On VLi8, LAN cards cause an IRQ conflict with the embedded sound de- vice under Win95. ⢠To solve the problem: Reserve IRQ 5 and sett PNP OS to no. For this: 1 Install the NIC then power up the system
General information to read before installing 2 Press F2 to go to CMOS setup. 3 Set PNP OS to NO and reserve IRQ 5. 4 Save settings and boot to applicable OS.
1 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows 95 SR2.5 1 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows 95 SR2.5 Connecting to a Windows NT 3.51 Server Requirements ⢠HP Vectra with Windows 95 SR2.5. ⢠3COM Etherlink III 3C590 PCI 10BT network adapter and driver disk ver- sion 5.2.2. ⢠Driver File: EL59X.SYS, version 1.22 ⢠Microsoft Windows 95 SR2.5 media. ⢠Microsoft Windows NT 3.51 Server system that supports NetBEUI, NWLink IPX/SPX Compatible Transport and NWLink NetBIOS network protocols. Device Configuration Procedure 1 With the HP Vectra turned off, install the 3COM 3C590 network adapter into a PCI slot. 2 Connect network cable media to the 3COM 3C590 network adapter. 3 Reboot the system to Windows 95SR2.5. 4 Windows 95SR2.5 will automatically recognize the 3COM 3C590 network adapter as â3Com 3C590 EtherLink IIIâ. 5 Insert the 3COM 3C590 driver disk in the floppy drive and click on âNextâ from the Update Device Driver Wizard dialog box. 6 When Windows 95 detects the updated driver, â3Com EtherLink III 3C590â, click on âFinishâ. Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8 Interrupt 5 03 07 I/O Address 210 210 210
1 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Connecting to a Windows NT 3.51 Server 7 During the Update Device Driver process, point to the appropriate file locations (i.e. drivers disk or Windows 95 CD) to install the necessary files. Keep newer files when a file being copied is older than the file currently on your computer. 8 Click on âOKâ when the system prompts for the computer and workgroup names. 9 Enter the Computer Name, Workgroup, and Computer Description in the appropriate spaces and click on âCloseâ (Contact your network administrator if you do not have the required information). 10 Click on âYESâ to restart the system when prompted. 11 Right-click on the âNetwork Neighborhoodâ icon and select âPropertiesâ. 12 Accept the default Network Protocols and the Primary Network Logon (Client for Microsoft Networks) as seen below and click on âOKâ. (If you do not have the required information, contact your network administrator) 13 Client for Microsoft Networks Client for Microsoft Networks 3Com EtherLink III 3Com TCAATDI Diagnostic TDI IPX/SPX-compatible Protocol NetBEUI 14 Click on âOKâ to accept the configuration. 15 When prompted, specify the path to your Windows 95 files. 16 Click on âYesâ when prompted to restart the system.
2 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows 95 SR2.5 2 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows 95 SR2.5 Connecting to a Windows NT 4.0 Server Requirements ⢠HP Vectra with Windows 95 SR2.5. ⢠3COM Etherlink III 3C590 PCI 10BT network adapter and driver disk ver- sion 5.2.2. ⢠Driver File: EL59X.SYS, version 1.22 ⢠Microsoft Windows 95 SR2.5 media. ⢠Microsoft Windows NT 4.0 Server system that supports NetBEUI, NWLink IPX/SPX Compatible Transport and NWLink NetBIOS network protocols. ⢠Device Configuration Procedure 1 With the HP Vectra turned off, install the 3COM 3C590 network adapter into a PCI slot. 2 Connect network cable media to the 3COM 3C590 network adapter. 3 Reboot the system to Windows 95SR2.5. 4 Windows 95SR2.5 will automatically recognize the 3COM 3C590 network card as â3Com 3C590 EtherLink IIIâ. 5 Insert the 3COM 3C590 driver disk in the floppy drive and click on âNextâ from the Update Device Driver Wizard dialog box. 6 When Windows 95 detects the updated driver, â3Com EtherLink III 3C590â, click on âFinishâ. 7 During the Update Device Driver process, point to the appropriate file locations (i.e. drivers disk or Windows 95 CD) to install the necessary files. Keep newer files when a file being copied is older than the file currently on your computer. Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8 Interrupt 05 03 07 I/O Address 210 210 210
2 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Connecting to a Windows NT 4.0 Server 8 Click on âOKâ when the system prompts for the computer and workgroup names. 9 Enter the Computer Name, Workgroup, and Computer Description in the appropriate spaces and click on âCloseâ (Contact your network administrator if you do not have the required information). 10 Click on âYESâ to restart the system when prompted. 11 Right-click on the âNetwork Neighborhoodâ icon and select âPropertiesâ. 12 Accept the default Network Protocols and the Primary Network Logon (Client for Microsoft Networks) as seen below and click on âOKâ. (If you do not have the required information, contact your network administrator) 13 Client for Microsoft Networks Client for Microsoft Networks 3Com EtherLink III 3Com TCAATDI Diagnostic TDI IPX/SPX-compatible Protocol NetBEUI 14 Click on âOKâ to accept the configuration. 15 When prompted, specify the path to your Windows 95 files. 16 Click on âYesâ when prompted to restart the system.
3 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows 95 SR2.5 3 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows 95 SR2.5 Connecting to a Netware 3.12 Server Requirements ⢠HP Vectra with Windows 95 SR2.5. ⢠3COM Etherlink III 3C590 PCI 10BT network adapter and driver disk ver- sion 5.2.2. ⢠Driver File: EL59X.SYS, version 1.22 ⢠Microsoft Windows 95 SR2.5 media. ⢠Novell Netware 3.12 Server that supports IPX network protocol. ⢠Novell Client for Windows 95 v2.5 installation media. Device Configuration Procedure 1 With the HP Vectra turned off, install the 3COM 3C590 network adapter into a PCI slot. 2 Connect network cable media to the 3COM 3C590 network adapter. 3 Reboot the system to Windows 95SR2.5. 4 Windows 95SR2.5 will automatically recognize the 3COM 3C590 network adapter as â3Com 3C590 EtherLink IIIâ. 5 Insert the 3COM 3C590 driver disk in the floppy drive and click on âNextâ from the Update Device Driver Wizard dialog box. 6 When Windows 95 detects the updated driver, â3Com EtherLink III 3C590â, click on âFinishâ. Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8 Interrupt 5 03 07 I/O Address 210 210 210
3 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Connecting to a Netware 3.12 Server 7 During the Update Device Driver process, point to the appropriate file locations (i.e. drivers disk or Windows 95 CD) to install the necessary files. Keep newer files when a file being copied is older than the file currently on your computer. 8 Click on âOKâ when the system prompts for the computer and workgroup names. 9 Enter the Computer Name, Workgroup, and Computer Description in the appropriate spaces and click on âCloseâ (Contact your network administrator if you do not have the required information). 10 Click on âYESâ to restart the system when prompted. 11 From the location of the âNovell Client for Windows 95 v.2.5â installation files, execute âSetup.exeâ. 12 Click on âYesâ to accept the License Agreement. 13 Select âCustomâ installation and click on âNextâ. 14 Select âBindery (NetWare 3.x)â and click on âNextâ. 15 Click on âInstallâ to start the installation. 16 Click on âYesâ to set the Preferred Server. (If you do not have the required information, contact your network administrator). 17 Click on âRebootâ to complete the installation. 18 Right-click on the âNetwork Neighborhoodâ icon and select âPropertiesâ. 19 Accept the default Network Protocols and the Primary Network Logon to (Novell NetWare Client) as seen below and click on âOKâ. (If you do not have the required information, contact your network administrator) 20 Novell NetWare Client Novell NetWare Client 3COM Etherlink III Bus-Master PCI Ethernet Adapter IPX 32-bit Protocol for the Novell NetWare Client IPX/SPX-compatible Protocol NetBEUI 21 When prompted, specify the path to your Windows 95 files. 22 Click on âYesâ when prompted to restart the system.
4 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows 95 SR2.5 4 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows 95 SR2.5 Connecting to a Netware 4.11 Server Requirements ⢠HP Vectra with Windows 95 SR2.5. ⢠3COM Etherlink III 3C590 PCI 10BT network adapter and driver disk ver- sion 5.2.2. ⢠Driver File: EL59X.SYS, version 1.22. ⢠Microsoft Windows 95 SR2.5 media. ⢠Novell Netware 4.11 Server that supports IPX network protocol. ⢠Novell Client for Windows 95 v2.5 installation media. Device Configuration Procedure 1 With the HP Vectra turned off, install the 3COM 3C590 network adapter into a PCI slot. 2 Connect network cable media to the 3COM 3C590 network adapter. 3 Reboot the system to Windows 95SR2.5. 4 Windows 95SR2.5 will automatically recognize the 3COM 3C590 network adapter as â3Com 3C590 EtherLink IIIâ. 5 Insert the 3COM 3C590 driver disk in the floppy drive and click on âNextâ from the Update Device Driver Wizard dialog box. 6 When Windows 95 detects the updated driver, â3Com EtherLink III 3C590â, click on âFinishâ. Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8 Interrupt 05 03 07 I/O Address 210 210 210
4 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Connecting to a Netware 4.11 Server 7 During the Update Device Driver process, point to the appropriate file locations (i.e. drivers disk or Windows 95 CD) to install the necessary files. Keep newer files when a file being copied is older than the file currently on your computer. 8 Click on âOKâ when the system prompts for the computer and workgroup names. 9 Enter the Computer Name, Workgroup, and Computer Description in the appropriate spaces and click on âCloseâ (Contact your network administrator if you do not have the required information). 10 Click on âYESâ to restart the system when prompted. 11 From the location of the âNovell Client for Windows 95 v.2.5â installation files, execute âSetup.exeâ. 12 Click on âYesâ to accept the License Agreement. 13 Select âCustomâ installation and click on âNextâ. 14 Select âNDIS (NetWare 4.x or higher)â and click on âNextâ. 15 Click on âInstallâ to start the installation. 16 Click on âYesâ to set the Preferred Tree, Server, etc. (If you do not have the required information, contact your network administrator). 17 Click on âRebootâ to complete the installation. 18 Right-click on the âNetwork Neighborhoodâ icon and select âPropertiesâ. 19 Accept the default Network Protocols and the Primary Network Logon to (Novell NetWare Client) as seen below and click on âOKâ. (If you do not have the required information, contact your network administrator) 20 Novell NetWare Client Novell NetWare Client 3COM Etherlink III Bus-Master PCI Ethernet Adapter IPX 32-bit Protocol for the Novell NetWare Client IPX/SPX-compatible Protocol NetBEUI 21 When prompted, specify the path to your Windows 95 files. 22 Click on âYesâ when prompted to restart the system.
5 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows NT 4.0 Workstation 5 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows NT 4.0 Workstation Connecting to a Windows NT 3.51 Server Requirements ⢠HP Vectra with Windows NT 4.0 Workstation. ⢠3COM Etherlink III 3C590 PCI 10BT network adapter and driver disk ver- sion 5.2.2. ⢠Driver File: EL59X.SYS, version 1.22 ⢠Microsoft Windows NT 4.0 Workstation media. ⢠Microsoft Windows NT 4.0 Service Pack 4. ⢠Microsoft Windows NT 3.51 Server system that supports NetBEUI, NWLink IPX/SPX Compatible Transport and NWLink NetBIOS network protocols. Device Configuration Procedure 1 With the HP Vectra turned off, install the 3COM 3C590 network adapter into a PCI slot. 2 Connect network cable media to the 3COM 3C590 network adapter. 3 Log onto Windows NT4 Workstation with administrator privileges (Contact your network administrator if you do not have the required information). 4 Right-click on the âNetwork Neighborhoodâ icon and select âPropertiesâ. 5 Click on âYesâ when prompted to install Windows NT Networking. 6 Select âWired to the networkâ and click on âNextâ. 7 Click on the âSelect from listâ¦â button and then the âHave Diskâ¦â button. Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8 Interrupt 11 03 10 I/O Address 1020 DCE0 E400
5 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Connecting to a Windows NT 3.51 Server 8 Insert the 3COM 3C590 driver disk into the floppy drive. 9 Set the path to âA:\NDIS\WINNT35\â in the dialog-box and click on âOKâ. 10 Choose by highlighting the â3Com EtherLink III PCI Bus-Master Adapter (3C590)â and click on âOKâ. 11 With â3Com EtherLink III PCI Bus-Master Adapter (3C590)â listed in the âNetwork Adaptersâ window, click on âNextâ. 12 Select the applicable network protocols and click on âNextâ (Contact your network administrator if you do not have the required information). 13 At the âNetwork Services:â prompt, accept default settings and click on âNextâ. 14 Click on âNextâ to continue the network card installation. 15 Set the path to âD:\I386â (D:\ represents the CD-ROM drive with the Windows NT4 Workstation CD) in the dialog box and click on âOKâ. 16 At the âShow Bindings for:â prompt, accept the default settings and click on âNextâ. 17 Click on âNextâ to start the network. 18 Specify your Computer Name, Workgroup or Domain (Contact your network administrator if you do not have the required information) and click on âNextâ. 19 Click on âFinishâ to complete the installation. 20 Select âYesâ at the prompt to shut down and restart your computer for the new settings to take effect. 21 Install the Windows NT4 Service Pack 4 application to correct the error messages in the Event Viewer. 22 Install the Hewlett-Packard Soft-Power Down application once the Service Pack 4 has been installed.
6 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows NT 4.0 Workstation 6 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows NT 4.0 Workstation Connecting to a Windows NT 4.0 Server Requirements ⢠HP Vectra with Windows NT 4.0 Workstation. ⢠3COM Etherlink III 3C590 PCI 10BT network adapter and driver disk ver- sion 5.2.2. ⢠Driver File: EL59X.SYS, version 1.22 ⢠Microsoft Windows NT 4.0 Workstation media. ⢠Microsoft Windows NT 4.0 Service Pack 4. ⢠Microsoft Windows NT 4.0 Server system that supports NetBEUI, NWLink IPX/SPX Compatible Transport and NWLink NetBIOS network protocols. Device Configuration Procedure 1 With the HP Vectra turned off, install the 3COM 3C590 network adapter into a PCI slot. 2 Connect network cable media to the 3COM 3C590 network adapter. 3 Log onto Windows NT4 Workstation with administrator privileges (Contact your network administrator if you do not have the required information). 4 Right-click on the âNetwork Neighborhoodâ icon and select âPropertiesâ. 5 Click on âYesâ when prompted to install Windows NT Networking. 6 Select âWired to the networkâ and click on âNextâ. 7 Click on the âSelect from listâ¦â button and then the âHave Diskâ¦â button. 8 Insert the 3COM driver disk into the floppy drive. Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8 Interrupt 05 05 05 I/O Address 300 300 300
6 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Connecting to a Windows NT 4.0 Server 9 Set the path to âA:\NDIS\WINNT35\â in the dialog-box and click on âOKâ. 10 Choose by highlighting the â3Com EtherLink III PCI Bus-Master Adapter (3C590)â and click on âOKâ. 11 With â3Com EtherLink III PCI Bus-Master Adapter (3C590)â listed in the âNetwork Adaptersâ window, click on âNextâ. 12 Select the applicable network protocols and click on âNextâ (Contact your network administrator if you do not have the required information). 13 At the âNetwork Services:â prompt, accept default settings and click on âNextâ. 14 Click on âNextâ to continue the network card installation. 15 Set the path to âD:\I386â (D:\ represents the CD-ROM drive with the Windows NT4 Workstation CD) in the dialog box and click on âOKâ. 16 At the âShow Bindings for:â prompt, accept the default settings and click on âNextâ. 17 Click on âNextâ to start the network. 18 Specify your Computer Name, Workgroup or Domain (Contact your network administrator if you do not have the required information) and click on âNextâ. 19 Click on âFinishâ to complete the installation. 20 Select âYesâ at the prompt to shut down and restart your computer for the new settings to take effect. 21 Install the Windows NT4 Service Pack 4 application to correct the error messages in the Event Viewer. 22 Install the Hewlett-Packard Soft-Power Down application once the Service Pack 4 has been installed.
7 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows NT 4.0 Workstation 7 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows NT 4.0 Workstation Connecting to a Novell NetWare 3.12 Server Requirements ⢠HP Vectra with Windows NT 4.0 Workstation. ⢠3COM Etherlink III 3C590 PCI 10BT network adapter and driver disk ver- sion 5.2.2. ⢠Driver File: EL59X.SYS, version 1.22 ⢠Microsoft Windows NT 4.0 Workstation media. ⢠Microsoft Windows NT 4.0 Service Pack 4. ⢠Novell NetWare 3.12 Server system that supports IPX network protocol. ⢠Novell IntranetWare Client for Windows NT v4.11b installation media. Device Configuration Procedure 1 With the HP Vectra turned off, install the 3COM 3C590 network adapter into a PCI slot. 2 Connect network cable media to the 3COM 3C590 network adapter. 3 Log onto Windows NT4 Workstation with administrator privileges (Contact your network administrator if you do not have the required information). 4 Right-click on the âNetwork Neighborhoodâ icon and select âPropertiesâ. 5 Click on âYesâ when prompted to install Windows NT Networking. 6 Select âWired to the networkâ and click on âNextâ. 7 Click on the âSelect from listâ¦â button and then the âHave Diskâ¦â button. Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8 Interrupt 05 05 05 I/O Address 300 300 300
7 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Connecting to a Novell NetWare 3.12 Server 8 Insert the 3COM driver disk into the floppy drive. 9 Set the path to âA:\NDIS\WINNT35\â in the dialog-box and click on âOKâ. 10 Choose by highlighting the â3Com EtherLink III PCI Bus-Master Adapter (3C590)â and click on âOKâ. 11 With â3Com EtherLink III PCI Bus-Master Adapter (3C590)â listed in the âNetwork Adaptersâ window, click on âNextâ. 12 Select the applicable network protocols and click on âNextâ (Contact your network administrator if you do not have the required information). 13 At the âNetwork Services:â prompt, accept default settings and click on âNextâ. 14 Click on âNextâ to continue the network card installation. 15 Set the path to âD:\I386â (D:\ represents the CD-ROM drive with the Windows NT4 Workstation CD) in the dialog box and click on âOKâ. 16 At the âShow Bindings for:â prompt, accept the default settings and click on âNextâ. 17 Click on âNextâ to start the network. 18 Specify your Computer Name, Workgroup or Domain (Contact your network administrator if you do not have the required information) and click on âNextâ. 19 Click on âFinishâ to complete the installation. 20 Remove the driver disk from the floppy drive and select âYesâ at the prompt to shut down and restart your computer for the new settings to take effect. 21 Log onto Windows NT4 Workstation with administrator privileges. 22 From the location of the âNovell IntranetWare Client v.4.11bâ installation files, execute âSetupnw.exeâ. 23 Click on âContinueâ to continue with the Novell IntranetWare Client installation. 24 Click on âYesâ to agree to the Software License Agreement to begin installation. 25 Click on the âRebootâ button at the completion of the Novell NetWare Client installation to restart the machine for changes to take effect. 26 Click on the âIntranetWareâ tab of the Novell IntranetWare Client Services Login screen. 27 Select âBindery Loginâ and specify the Server Name (Contact your network administrator if you do not have the required information). 28 Click on the âLoginâ tab and specify your Name and Password to login.
7 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Connecting to a Novell NetWare 3.12 Server 29 Install the Windows NT4 Service Pack 4 application to correct the error messages in the Event Viewer. 30 Install the Hewlett-Packard Soft Power Down application once the Service Pack 4 has been installed.
8 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows NT 4.0 Workstation 8 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows NT 4.0 Workstation Connecting to a Novell NetWare 4.11 Server Requirements ⢠HP Vectra with Windows NT 4.0 Workstation. ⢠3COM Etherlink III 3C590 PCI 10BT network adapter and driver disk ver- sion 5.2.2. ⢠Driver File: EL59X.SYS, version 1.22 ⢠Microsoft Windows NT 4.0 Workstation media. ⢠Microsoft Windows NT 4.0 Service Pack 4. ⢠Novell NetWare 4.11 Server system that supports IPX network protocol. ⢠Novell IntranetWare Client for Windows NT v4.11b installation media. Device Configuration Procedure 1 With the HP Vectra turned off, install the 3COM 3C590 network adapter into a PCI slot. 2 Connect network cable media to the 3COM 3C590 network adapter. 3 Log onto Windows NT4 Workstation with administrator privileges (Contact your network administrator if you do not have the required information). 4 Right-click on the âNetwork Neighborhoodâ icon and select âPropertiesâ. 5 Click on âYesâ when prompted to install Windows NT Networking. 6 Select âWired to the networkâ and click on âNextâ. 7 Click on the âSelect from listâ¦â button and then the âHave Diskâ¦â button. Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8 Interrupt 05 05 05 I/O Address 300 300 300
8 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Connecting to a Novell NetWare 4.11 Server 8 Insert the 3COM driver disk into the floppy drive. 9 Set the path to âA:\NDIS\WINNT35\â in the dialog-box and click on âOKâ. 10 Choose by highlighting the â3Com EtherLink III PCI Bus-Master Adapter (3C590)â and click on âOKâ. 11 With â3Com EtherLink III PCI Bus-Master Adapter (3C590)â listed in the âNetwork Adaptersâ window, click on âNextâ. 12 Select the applicable network protocols and click on âNextâ (Contact your network administrator if you do not have the required information). 13 At the âNetwork Services:â prompt, accept default settings and click on âNextâ. 14 Click on âNextâ to continue the network card installation. 15 Set the path to âD:\I386â (D:\ represents the CD-ROM drive with the Windows NT4 Workstation CD) in the dialog box and click on âOKâ. 16 At the âShow Bindings for:â prompt, accept the default settings and click on âNextâ. 17 Click on âNextâ to start the network. 18 Specify your Computer Name, Workgroup or Domain (Contact your network administrator if you do not have the required information) and click on âNextâ. 19 Click on âFinishâ to complete the installation. 20 Remove the driver disk from the floppy drive and select âYesâ at the prompt to shut down and restart your computer for the new settings to take effect. 21 Log onto Windows NT4 Workstation with administrator privileges. 22 From the location of the âNovell IntranetWare Client v.4.11bâ installation files, execute âSetupnw.exeâ. 23 Click on âContinueâ to continue with the Novell IntranetWare Client installation. 24 Click on âYesâ to agree to the Software License Agreement to begin installation. 25 Click on the âRebootâ button at the completion of the Novell NetWare Client installation to restart the machine for changes to take effect. 26 Click on the âIntranetWareâ tab of the Novell IntranetWare Client Services Login screen. 27 Select âNDS Loginâ and specify the Tree, Server Name, etc. (Contact your network administrator if you do not have the required information). 28 Click on the âLoginâ tab and specify your Name and Password to login.
8 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Connecting to a Novell NetWare 4.11 Server 29 Install the Windows NT4 Service Pack 4 application to correct the error messages in the Event Viewer. 30 Install the Hewlett-Packard Soft Power Down application once the Service Pack 4 has been installed.
9 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows NT3.51 Workstation 9 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows NT3.51 Workstation Connecting to a Windows NT 3.51 Server Requirements ⢠HP Vectra with Windows NT 3.51 Workstation. ⢠3COM Etherlink III 3C590 PCI 10BT network adapter and driver disk ver- sion 5.2.2. ⢠Driver File: EL59X.SYS, version 1.22 ⢠Microsoft Windows NT 3.51 Workstation media. ⢠Microsoft Windows NT 3.51 Service Pack 5 media. ⢠Microsoft Windows NT 3.51 Server system that supports NetBEUI, NWLink IPX/SPX Compatible Transport and NWLink NetBIOS network protocols. Device Configuration Procedure 1 With the HP Vectra turned off, install the 3COM 3C590 network adapter into a PCI slot. 2 Connect network cable media to the 3COM 3C590 network adapter. 3 Log into Windows NT with administrator privileges. 4 Open the âNetworkâ icon in the âControl Panelâ program group. 5 Click on âYESâ in the âNetwork Settingsâ dialog box to install Windows NT Networking. 6 Insert the Windows NT 3.51Workstation CD in the CD-ROM drive. 7 Set the path to âD:\I386â (D:\ represents the CD-ROM drive with the Windows NT 3.51 CD) in the dialog-box of the Windows NT Setup window and click on âContinueâ. Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8 Interrupt 10 05 05 I/O Address 300 300 300
9 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Connecting to a Windows NT 3.51 Server 8 Click on the âDo Not Detectâ button from the âNetwork Adapter Card Detectionâ window, and click on the âContinueâ button in the following âNetwork Adapter Card Detectionâ window. 9 From the âDrop Down Listâ, scroll down and select â<Other> Requires disk from manufacturerâ, then click on âContinueâ. 10 Set the path to âA:\NDIS\WINNT35\â in the âInsert Diskâ dialog box, and then insert the 3COM âEtherDisk for the Fast EtherLink and EtherLink III Bus Master Adaptersâ diskette in the floppy drive and click âOKâ. 11 Select â3COM Fast Etherlink PCI Bus-Master Adapter (3C590)â in the âSelect OEM Optionâ dialog box, and click âOKâ. 12 Choose the appropriate network protocols by clicking the check boxes in the âWindows NT Setupâ dialog box and click on the âContinueâ button (Contact your network administrator if you do not have the required information). 13 Press âOKâ to continue from âNetwork Settingsâ dialog box. 14 If applicable, press âOKâ to continue from âNWLink IPX/SPX Protocol Configurationâ dialog box. 15 At the âDomain/Workgroup Settingsâ dialog box, click on âOKâ to accept the default âWorkgroupâ as your workgroup name. 16 To complete the installation, remove the floppy disk, and click on âRestart computerâ in the âWindows NT Workstation Networking Setupâ dialog box. 17 Install the Windows NT3.51 Service Pack 5 application.
10 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows NT 3.51 Workstation 10 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows NT 3.51 Workstation Connecting to a Windows NT 4.0 Server Requirements ⢠HP Vectra with Windows NT 3.51 Workstation. ⢠3COM Etherlink III 3C590 PCI 10BT network adapter and driver disk ver- sion 5.2.2. ⢠Driver File: EL59X.SYS, version 1.22 ⢠Microsoft Windows NT 3.51 Workstation media. ⢠Microsoft Windows NT 3.51 Service Pack 5 media. ⢠Microsoft Windows NT 4.0 Server system that supports NetBEUI, NWLink IPX/SPX Compatible Transport and NWLink NetBIOS network protocols. Device Configuration Procedure 1 With the HP Vectra turned off, install the 3COM 3C590 network adapter into a PCI slot. 2 Connect network cable media to the 3COM 3C590 network adapter. 3 Log into Windows NT with administrator privileges. 4 Open the âNetworkâ icon in the âControl Panelâ program group. 5 Click on âYESâ in the âNetwork Settingsâ dialog box to install Windows NT Networking. 6 Insert the Windows NT 3.51Workstation CD in the CD-ROM drive. 7 Set the path to âD:\I386â (D:\ represents the CD-ROM drive with the Windows NT 3.51 CD) in the dialog-box of the Windows NT Setup window and click on âContinueâ. Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8 Interrupt 10 05 05 I/O Address 300 300 300
10 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Connecting to a Windows NT 4.0 Server 8 Click on the âDo Not Detectâ button from the âNetwork Adapter Card Detectionâ window, and click on the âContinueâ button in the following âNetwork Adapter Card Detectionâ window. 9 From the âDrop Down Listâ, scroll down and select â<Other> Requires disk from manufacturerâ, then click on âContinueâ. 10 Set the path to âA:\NDIS\WINNT35\â in the âInsert Diskâ dialog box, and then insert the 3COM âEtherDisk for the Fast EtherLink and EtherLink III Bus Master Adaptersâ diskette in the floppy drive and click âOKâ. 11 Select â3COM Fast Etherlink PCI Bus-Master Adapter (3C590)â in the âSelect OEM Optionâ dialog box, and click âOKâ. 12 Choose the appropriate network protocols by clicking the check boxes in the âWindows NT Setupâ dialog box and click on the âContinueâ button (Contact your network administrator if you do not have the required information). 13 Press âOKâ to continue from âNetwork Settingsâ dialog box. 14 If applicable, press âOKâ to continue from âNWLink IPX/SPX Protocol Configurationâ dialog box. 15 At the âDomain/Workgroup Settingsâ dialog box, click on âOKâ to accept the default âWorkgroupâ as your workgroup name. 16 To complete the installation, remove the floppy disk, and click on âRestart computerâ in the âWindows NT Workstation Networking Setupâ dialog box. 17 Install the Windows NT3.51 Service Pack 5 application.
11 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows NT 3.51 Workstation 11 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows NT 3.51 Workstation Connecting to a Novell NetWare 4.11 Server Requirements ⢠HP Vectra with Windows NT3.51 Workstation. ⢠3COM Etherlink III 3C590 PCI 10BT network adapter and driver disk ver- sion 5.2.2. ⢠Driver File: EL59X.SYS, version 1.22 ⢠Microsoft Windows NT 3.51 Workstation media. ⢠Microsoft Windows NT 3.51 Service Pack 5 media. ⢠Novell NetWare 4.11 Server system that supports IPX network protocol. ⢠Novell IntranetWare Client for Windows NT v4.11b installation media. Device Configuration Procedure 1 With the HP Vectra turned off, install the 3COM 3C590 network adapter into a PCI slot. 2 Connect network cable media to the 3COM 3C590 network adapter. 3 Log into Windows NT with administrator privileges. 4 Open the âNetworkâ icon in the âControl Panelâ program group. 5 Click on âYESâ in the âNetwork Settingsâ dialog box to install Windows NT Networking. 6 Insert the Windows NT 3.51Workstation CD in the CD-ROM drive. 7 Set the path to âD:\I386â (D:\ represents the CD-ROM drive with the Windows NT 3.51 CD) in the dialog-box of the Windows NT Setup window and click on âContinueâ. Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8 Interrupt 10 05 05 I/O Address 300 300 300
11 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Connecting to a Novell NetWare 4.11 Server 8 Click on the âDo Not Detectâ button from the âNetwork Adapter Card Detectionâ window, and click on the âContinueâ button in the following âNetwork Adapter Card Detectionâ window. 9 From the âDrop Down Listâ, scroll down and select â<Other> Requires disk from manufacturerâ, then click on âContinueâ. 10 Set the path to âA:\NDIS\WINNT35\â in the âInsert Diskâ dialog box, and then insert the 3COM âEtherDisk for the Fast EtherLink and EtherLink III Bus Master Adaptersâ diskette in the floppy drive and click âOKâ. 11 Select â3COM Fast Etherlink PCI Bus-Master Adapter (3C590)â in the âSelect OEM Optionâ dialog box, and click âOKâ. 12 Choose the appropriate network protocols by clicking the check boxes in the âWindows NT Setupâ dialog box and click on the âContinueâ button (Contact your network administrator if you do not have the required information). 13 Press âOKâ to continue from âNetwork Settingsâ dialog box. 14 If applicable, press âOKâ to continue from âNWLink IPX/SPX Protocol Configurationâ dialog box. 15 At the âDomain/Workgroup Settingsâ dialog box, click on âOKâ to accept the default âWorkgroupâ as your workgroup name. 16 To complete the installation, remove the floppy disk, and click on âRestart computerâ in the âWindows NT Workstation Networking Setupâ dialog box. 17 Insert the Novell IntranetWare Client v.4.11 application CD in the CD- ROM drive and execute âSetupnw.exeâ. 18 Click on the âContinueâ button to proceed with the installation of the Novell IntranetWare Client. 19 Click on the âRebootâ button to restart the machine for the changes to take effect. 20 Install the Windows NT3.51 Service Pack 5 application.
12 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows for Workgroups 3.11 12 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows for Workgroups 3.11 Connecting to a Windows NT 4.0 Server Requirements ⢠HP Vectra with MS-DOS and MS-Windows for Workgroups 3.11 ⢠3COM Etherlink III 3C590 PCI 10BT network adapter and driver disk ver- sion 5.2.2. ⢠Driver File: EL59X.386, version 1.18 ⢠Microsoft Windows for Workgroups 3.11 media. ⢠Microsoft Windows NT 4.0 Server system that supports NetBEUI, NWLink IPX/SPX Compatible Transport and NWLink NetBIOS network protocols. ⢠Device Configuration Procedure 1 With the HP Vectra turned off, install the 3COM 3C590 network adapter into a PCI slot. 2 Connect network cable media to the 3COM 3C590 network adapter. 3 After Windows loads, open the âNETWORKâ Program Group, and double- click on âNetwork Setupâ. 4 Click on the âNetworksâ button in the âNetwork Setupâ dialog box. 5 Click on the âInstall Microsoft Windows Network:â option, and click âOKâ. 6 Click on the âDriversâ button from the âNetwork Setupâ dialog box, and click on âAdd Adapterâ. 7 Click âOKâ to accept the default choice of âUnlisted or Updated Network Adapterâ. 8 Type the path âA:\NDIS\WFWâ in the âInstall Driverâ dialog box, and then insert the 3COM 3C590 driver disk into the floppy drive, and click âOKâ. Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8 Interrupt 05 05 05 I/O Address 300 300 300
12 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Connecting to a Windows NT 4.0 Server 9 Select â3COM Fast EtherLink/EtherLink III Bus Master Adapter (3C59X)â in the âUnlisted or Updated Network Adapterâ dialog box, and click âOKâ. 10 Make sure that the â3COM Fast EtherLink/EtherLink III Bus Master Adapter (3C59X)â is selected in âNetwork Driversâ. 11 Accept the applicable network protocols, and then click on âCLOSEâ. 12 At the âNetwork Setupâ dialog box, click on âOKâ. 13 Specify your User Name, Workgroup, and Computer Name in âMicrosoft Windows Network Namesâ dialog box, and click on âOKâ. (The Drivers will now start to copy). 14 To complete the installation, remove the Intel diskette from the floppy drive and click on âRestart Computerâ button in the âWindows Setupâ dialog box.
13 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows for Workgroups 3.11 13 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows for Workgroups 3.11 Connecting to a Novell NetWare 4.11 Server Requirements ⢠HP Vectra with DOS and MS-Windows for Workgroups 3.11. ⢠3COM Etherlink III 3C590 PCI 10BT network adapter and driver disk ver- sion 5.2.2. ⢠Driver File: EL59X.386, version 1.18 ⢠Microsoft Windows for Workgroups 3.11 media. ⢠Novell NetWare 4.11 Server system that supports IPX network protocol. ⢠NetWare Client for DOS and MS Windows v1.21 installation media. Device Configuration Procedure 1 With the HP Vectra turned off, install the 3COM 3C590 network adapter into a PCI slot. 2 Connect network cable media to the 3COM 3C590 network adapter. 3 From the location of the âNetWare Client for DOS and Windows v1.21â installation files, execute âInstall.exeâ. 4 Select option 5 âSelect the driver for your network boardâ and press âEnterâ. 5 Select âOTHER DRIVERSâfrom the Network Board selection. 6 Insert the 3COM 3C590 driver disk into the floppy drive. 7 Type the path âA:\NETWARE\CLIENTâ when prompted and press âEnterâ. 8 Select â3Com Fast EtherLink/EtherLink III Bus Master Familyâ and hit âEnterâ. Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8 Interrupt 05 05 05 I/O Address 210 300 300
13 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Connecting to a Novell NetWare 4.11 Server 9 Accept the default network board settings and press âF10â to save it. 10 Select option 6 âHighlight here and press <Enter> to installâ and press âEnterâ to begin installation. 11 When the installation is finished, remove the 3COM 3C590 driver disk from the floppy drive and press <CTR><ALT><DEL> to restart the system. 12 You may login to a server from the DOS prompt or load Windows for Workgroup v3.11 and use the âNetWare User Toolsâ from the NetWare Tools folder to login to a server. (If you do not have the required information, contact your network administrator).
Notice The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by Hewlett-Packard. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of Hewlett-Packard Company. Microsoft®, Windows® and MS-DOS® are registered trademarks of Microsoft Corporation. MMX TM is a trademark of Intel Corporation. Pentium® is a registered trademark of Intel Corporation. Hewlett-Packard France Commercial Desktop Computing Division 38053 Grenoble Cedex 9 France ©1999 Hewlett Packard Company
General information to read before installing General information to read before installing On all systems : b efore installing LAN card, go into Bios setup and set PnP OS field to NO. ⢠How to change LAN card configuration if needed (Advanced users only) This is a general advisory on how to forcibly modify resources for ISA and PCI network cards. ISA cards: ⢠For ISA network adapters, start the configuration tool provided in driver kit (See install documentation) ⢠Under CMOS setup, go to Advanced > PnP/PCI ISA IRQ Resource Exclu- sion > reserve an IRQ for the adapter. PCI cards: ⢠For PCI network adapters, go to CMOS setup > Advanced > PnP/PCI ISA IRQ Resource Exclusion > reserve the IRQ for Legacy ISA. ⢠ISA cards canât use IRQ9 ⢠IRQ 9 is reported as being used by ACPI during POST. This is due to ISAâs inability to share IRQs. ⢠Using a different IRQ (e.g. 5, 7, 10, and 11) will work. For this: 1 Install the NIC then power up the system. 2 Press F2 to go to CMOS setup. 3 Set PnP OS to NO and reserve IRQ 5, 7, 10, or 11 (explained in installation section) 4 Save the configuration settings and boot to the applicable OS. 5 Follow installation steps. Sound conflict under Win 95 on VLi8 only ⢠On VLi8, LAN cards cause an IRQ conflict with the embedded sound de- vice under Win95. ⢠To solve the problem: Reserve IRQ 5 and sett PNP OS to no. For this: 1 Install the NIC then power up the system
General information to read before installing 2 Press F2 to go to CMOS setup. 3 Set PNP OS to NO and reserve IRQ 5. 4 Save settings and boot to applicable OS.
1 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows 95 SR2.5 1 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows 95 SR2.5 Connecting to a Windows NT 3.51 Server Requirements ⢠HP Vectra with Windows 95 SR2.5. ⢠3COM Etherlink III 3C590 PCI 10BT network adapter and driver disk ver- sion 5.2.2. ⢠Driver File: EL59X.SYS, version 1.22 ⢠Microsoft Windows 95 SR2.5 media. ⢠Microsoft Windows NT 3.51 Server system that supports NetBEUI, NWLink IPX/SPX Compatible Transport and NWLink NetBIOS network protocols. Device Configuration Procedure 1 With the HP Vectra turned off, install the 3COM 3C590 network adapter into a PCI slot. 2 Connect network cable media to the 3COM 3C590 network adapter. 3 Reboot the system to Windows 95SR2.5. 4 Windows 95SR2.5 will automatically recognize the 3COM 3C590 network adapter as â3Com 3C590 EtherLink IIIâ. 5 Insert the 3COM 3C590 driver disk in the floppy drive and click on âNextâ from the Update Device Driver Wizard dialog box. 6 When Windows 95 detects the updated driver, â3Com EtherLink III 3C590â, click on âFinishâ. Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8 Interrupt 5 03 07 I/O Address 210 210 210
1 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Connecting to a Windows NT 3.51 Server 7 During the Update Device Driver process, point to the appropriate file locations (i.e. drivers disk or Windows 95 CD) to install the necessary files. Keep newer files when a file being copied is older than the file currently on your computer. 8 Click on âOKâ when the system prompts for the computer and workgroup names. 9 Enter the Computer Name, Workgroup, and Computer Description in the appropriate spaces and click on âCloseâ (Contact your network administrator if you do not have the required information). 10 Click on âYESâ to restart the system when prompted. 11 Right-click on the âNetwork Neighborhoodâ icon and select âPropertiesâ. 12 Accept the default Network Protocols and the Primary Network Logon (Client for Microsoft Networks) as seen below and click on âOKâ. (If you do not have the required information, contact your network administrator) 13 Client for Microsoft Networks Client for Microsoft Networks 3Com EtherLink III 3Com TCAATDI Diagnostic TDI IPX/SPX-compatible Protocol NetBEUI 14 Click on âOKâ to accept the configuration. 15 When prompted, specify the path to your Windows 95 files. 16 Click on âYesâ when prompted to restart the system.
2 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows 95 SR2.5 2 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows 95 SR2.5 Connecting to a Windows NT 4.0 Server Requirements ⢠HP Vectra with Windows 95 SR2.5. ⢠3COM Etherlink III 3C590 PCI 10BT network adapter and driver disk ver- sion 5.2.2. ⢠Driver File: EL59X.SYS, version 1.22 ⢠Microsoft Windows 95 SR2.5 media. ⢠Microsoft Windows NT 4.0 Server system that supports NetBEUI, NWLink IPX/SPX Compatible Transport and NWLink NetBIOS network protocols. ⢠Device Configuration Procedure 1 With the HP Vectra turned off, install the 3COM 3C590 network adapter into a PCI slot. 2 Connect network cable media to the 3COM 3C590 network adapter. 3 Reboot the system to Windows 95SR2.5. 4 Windows 95SR2.5 will automatically recognize the 3COM 3C590 network card as â3Com 3C590 EtherLink IIIâ. 5 Insert the 3COM 3C590 driver disk in the floppy drive and click on âNextâ from the Update Device Driver Wizard dialog box. 6 When Windows 95 detects the updated driver, â3Com EtherLink III 3C590â, click on âFinishâ. 7 During the Update Device Driver process, point to the appropriate file locations (i.e. drivers disk or Windows 95 CD) to install the necessary files. Keep newer files when a file being copied is older than the file currently on your computer. Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8 Interrupt 05 03 07 I/O Address 210 210 210
2 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Connecting to a Windows NT 4.0 Server 8 Click on âOKâ when the system prompts for the computer and workgroup names. 9 Enter the Computer Name, Workgroup, and Computer Description in the appropriate spaces and click on âCloseâ (Contact your network administrator if you do not have the required information). 10 Click on âYESâ to restart the system when prompted. 11 Right-click on the âNetwork Neighborhoodâ icon and select âPropertiesâ. 12 Accept the default Network Protocols and the Primary Network Logon (Client for Microsoft Networks) as seen below and click on âOKâ. (If you do not have the required information, contact your network administrator) 13 Client for Microsoft Networks Client for Microsoft Networks 3Com EtherLink III 3Com TCAATDI Diagnostic TDI IPX/SPX-compatible Protocol NetBEUI 14 Click on âOKâ to accept the configuration. 15 When prompted, specify the path to your Windows 95 files. 16 Click on âYesâ when prompted to restart the system.
3 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows 95 SR2.5 3 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows 95 SR2.5 Connecting to a Netware 3.12 Server Requirements ⢠HP Vectra with Windows 95 SR2.5. ⢠3COM Etherlink III 3C590 PCI 10BT network adapter and driver disk ver- sion 5.2.2. ⢠Driver File: EL59X.SYS, version 1.22 ⢠Microsoft Windows 95 SR2.5 media. ⢠Novell Netware 3.12 Server that supports IPX network protocol. ⢠Novell Client for Windows 95 v2.5 installation media. Device Configuration Procedure 1 With the HP Vectra turned off, install the 3COM 3C590 network adapter into a PCI slot. 2 Connect network cable media to the 3COM 3C590 network adapter. 3 Reboot the system to Windows 95SR2.5. 4 Windows 95SR2.5 will automatically recognize the 3COM 3C590 network adapter as â3Com 3C590 EtherLink IIIâ. 5 Insert the 3COM 3C590 driver disk in the floppy drive and click on âNextâ from the Update Device Driver Wizard dialog box. 6 When Windows 95 detects the updated driver, â3Com EtherLink III 3C590â, click on âFinishâ. Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8 Interrupt 5 03 07 I/O Address 210 210 210
3 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Connecting to a Netware 3.12 Server 7 During the Update Device Driver process, point to the appropriate file locations (i.e. drivers disk or Windows 95 CD) to install the necessary files. Keep newer files when a file being copied is older than the file currently on your computer. 8 Click on âOKâ when the system prompts for the computer and workgroup names. 9 Enter the Computer Name, Workgroup, and Computer Description in the appropriate spaces and click on âCloseâ (Contact your network administrator if you do not have the required information). 10 Click on âYESâ to restart the system when prompted. 11 From the location of the âNovell Client for Windows 95 v.2.5â installation files, execute âSetup.exeâ. 12 Click on âYesâ to accept the License Agreement. 13 Select âCustomâ installation and click on âNextâ. 14 Select âBindery (NetWare 3.x)â and click on âNextâ. 15 Click on âInstallâ to start the installation. 16 Click on âYesâ to set the Preferred Server. (If you do not have the required information, contact your network administrator). 17 Click on âRebootâ to complete the installation. 18 Right-click on the âNetwork Neighborhoodâ icon and select âPropertiesâ. 19 Accept the default Network Protocols and the Primary Network Logon to (Novell NetWare Client) as seen below and click on âOKâ. (If you do not have the required information, contact your network administrator) 20 Novell NetWare Client Novell NetWare Client 3COM Etherlink III Bus-Master PCI Ethernet Adapter IPX 32-bit Protocol for the Novell NetWare Client IPX/SPX-compatible Protocol NetBEUI 21 When prompted, specify the path to your Windows 95 files. 22 Click on âYesâ when prompted to restart the system.
4 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows 95 SR2.5 4 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows 95 SR2.5 Connecting to a Netware 4.11 Server Requirements ⢠HP Vectra with Windows 95 SR2.5. ⢠3COM Etherlink III 3C590 PCI 10BT network adapter and driver disk ver- sion 5.2.2. ⢠Driver File: EL59X.SYS, version 1.22. ⢠Microsoft Windows 95 SR2.5 media. ⢠Novell Netware 4.11 Server that supports IPX network protocol. ⢠Novell Client for Windows 95 v2.5 installation media. Device Configuration Procedure 1 With the HP Vectra turned off, install the 3COM 3C590 network adapter into a PCI slot. 2 Connect network cable media to the 3COM 3C590 network adapter. 3 Reboot the system to Windows 95SR2.5. 4 Windows 95SR2.5 will automatically recognize the 3COM 3C590 network adapter as â3Com 3C590 EtherLink IIIâ. 5 Insert the 3COM 3C590 driver disk in the floppy drive and click on âNextâ from the Update Device Driver Wizard dialog box. 6 When Windows 95 detects the updated driver, â3Com EtherLink III 3C590â, click on âFinishâ. Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8 Interrupt 05 03 07 I/O Address 210 210 210
4 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Connecting to a Netware 4.11 Server 7 During the Update Device Driver process, point to the appropriate file locations (i.e. drivers disk or Windows 95 CD) to install the necessary files. Keep newer files when a file being copied is older than the file currently on your computer. 8 Click on âOKâ when the system prompts for the computer and workgroup names. 9 Enter the Computer Name, Workgroup, and Computer Description in the appropriate spaces and click on âCloseâ (Contact your network administrator if you do not have the required information). 10 Click on âYESâ to restart the system when prompted. 11 From the location of the âNovell Client for Windows 95 v.2.5â installation files, execute âSetup.exeâ. 12 Click on âYesâ to accept the License Agreement. 13 Select âCustomâ installation and click on âNextâ. 14 Select âNDIS (NetWare 4.x or higher)â and click on âNextâ. 15 Click on âInstallâ to start the installation. 16 Click on âYesâ to set the Preferred Tree, Server, etc. (If you do not have the required information, contact your network administrator). 17 Click on âRebootâ to complete the installation. 18 Right-click on the âNetwork Neighborhoodâ icon and select âPropertiesâ. 19 Accept the default Network Protocols and the Primary Network Logon to (Novell NetWare Client) as seen below and click on âOKâ. (If you do not have the required information, contact your network administrator) 20 Novell NetWare Client Novell NetWare Client 3COM Etherlink III Bus-Master PCI Ethernet Adapter IPX 32-bit Protocol for the Novell NetWare Client IPX/SPX-compatible Protocol NetBEUI 21 When prompted, specify the path to your Windows 95 files. 22 Click on âYesâ when prompted to restart the system.
5 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows NT 4.0 Workstation 5 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows NT 4.0 Workstation Connecting to a Windows NT 3.51 Server Requirements ⢠HP Vectra with Windows NT 4.0 Workstation. ⢠3COM Etherlink III 3C590 PCI 10BT network adapter and driver disk ver- sion 5.2.2. ⢠Driver File: EL59X.SYS, version 1.22 ⢠Microsoft Windows NT 4.0 Workstation media. ⢠Microsoft Windows NT 4.0 Service Pack 4. ⢠Microsoft Windows NT 3.51 Server system that supports NetBEUI, NWLink IPX/SPX Compatible Transport and NWLink NetBIOS network protocols. Device Configuration Procedure 1 With the HP Vectra turned off, install the 3COM 3C590 network adapter into a PCI slot. 2 Connect network cable media to the 3COM 3C590 network adapter. 3 Log onto Windows NT4 Workstation with administrator privileges (Contact your network administrator if you do not have the required information). 4 Right-click on the âNetwork Neighborhoodâ icon and select âPropertiesâ. 5 Click on âYesâ when prompted to install Windows NT Networking. 6 Select âWired to the networkâ and click on âNextâ. 7 Click on the âSelect from listâ¦â button and then the âHave Diskâ¦â button. Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8 Interrupt 11 03 10 I/O Address 1020 DCE0 E400
5 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Connecting to a Windows NT 3.51 Server 8 Insert the 3COM 3C590 driver disk into the floppy drive. 9 Set the path to âA:\NDIS\WINNT35\â in the dialog-box and click on âOKâ. 10 Choose by highlighting the â3Com EtherLink III PCI Bus-Master Adapter (3C590)â and click on âOKâ. 11 With â3Com EtherLink III PCI Bus-Master Adapter (3C590)â listed in the âNetwork Adaptersâ window, click on âNextâ. 12 Select the applicable network protocols and click on âNextâ (Contact your network administrator if you do not have the required information). 13 At the âNetwork Services:â prompt, accept default settings and click on âNextâ. 14 Click on âNextâ to continue the network card installation. 15 Set the path to âD:\I386â (D:\ represents the CD-ROM drive with the Windows NT4 Workstation CD) in the dialog box and click on âOKâ. 16 At the âShow Bindings for:â prompt, accept the default settings and click on âNextâ. 17 Click on âNextâ to start the network. 18 Specify your Computer Name, Workgroup or Domain (Contact your network administrator if you do not have the required information) and click on âNextâ. 19 Click on âFinishâ to complete the installation. 20 Select âYesâ at the prompt to shut down and restart your computer for the new settings to take effect. 21 Install the Windows NT4 Service Pack 4 application to correct the error messages in the Event Viewer. 22 Install the Hewlett-Packard Soft-Power Down application once the Service Pack 4 has been installed.
6 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows NT 4.0 Workstation 6 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows NT 4.0 Workstation Connecting to a Windows NT 4.0 Server Requirements ⢠HP Vectra with Windows NT 4.0 Workstation. ⢠3COM Etherlink III 3C590 PCI 10BT network adapter and driver disk ver- sion 5.2.2. ⢠Driver File: EL59X.SYS, version 1.22 ⢠Microsoft Windows NT 4.0 Workstation media. ⢠Microsoft Windows NT 4.0 Service Pack 4. ⢠Microsoft Windows NT 4.0 Server system that supports NetBEUI, NWLink IPX/SPX Compatible Transport and NWLink NetBIOS network protocols. Device Configuration Procedure 1 With the HP Vectra turned off, install the 3COM 3C590 network adapter into a PCI slot. 2 Connect network cable media to the 3COM 3C590 network adapter. 3 Log onto Windows NT4 Workstation with administrator privileges (Contact your network administrator if you do not have the required information). 4 Right-click on the âNetwork Neighborhoodâ icon and select âPropertiesâ. 5 Click on âYesâ when prompted to install Windows NT Networking. 6 Select âWired to the networkâ and click on âNextâ. 7 Click on the âSelect from listâ¦â button and then the âHave Diskâ¦â button. 8 Insert the 3COM driver disk into the floppy drive. Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8 Interrupt 05 05 05 I/O Address 300 300 300
6 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Connecting to a Windows NT 4.0 Server 9 Set the path to âA:\NDIS\WINNT35\â in the dialog-box and click on âOKâ. 10 Choose by highlighting the â3Com EtherLink III PCI Bus-Master Adapter (3C590)â and click on âOKâ. 11 With â3Com EtherLink III PCI Bus-Master Adapter (3C590)â listed in the âNetwork Adaptersâ window, click on âNextâ. 12 Select the applicable network protocols and click on âNextâ (Contact your network administrator if you do not have the required information). 13 At the âNetwork Services:â prompt, accept default settings and click on âNextâ. 14 Click on âNextâ to continue the network card installation. 15 Set the path to âD:\I386â (D:\ represents the CD-ROM drive with the Windows NT4 Workstation CD) in the dialog box and click on âOKâ. 16 At the âShow Bindings for:â prompt, accept the default settings and click on âNextâ. 17 Click on âNextâ to start the network. 18 Specify your Computer Name, Workgroup or Domain (Contact your network administrator if you do not have the required information) and click on âNextâ. 19 Click on âFinishâ to complete the installation. 20 Select âYesâ at the prompt to shut down and restart your computer for the new settings to take effect. 21 Install the Windows NT4 Service Pack 4 application to correct the error messages in the Event Viewer. 22 Install the Hewlett-Packard Soft-Power Down application once the Service Pack 4 has been installed.
7 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows NT 4.0 Workstation 7 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows NT 4.0 Workstation Connecting to a Novell NetWare 3.12 Server Requirements ⢠HP Vectra with Windows NT 4.0 Workstation. ⢠3COM Etherlink III 3C590 PCI 10BT network adapter and driver disk ver- sion 5.2.2. ⢠Driver File: EL59X.SYS, version 1.22 ⢠Microsoft Windows NT 4.0 Workstation media. ⢠Microsoft Windows NT 4.0 Service Pack 4. ⢠Novell NetWare 3.12 Server system that supports IPX network protocol. ⢠Novell IntranetWare Client for Windows NT v4.11b installation media. Device Configuration Procedure 1 With the HP Vectra turned off, install the 3COM 3C590 network adapter into a PCI slot. 2 Connect network cable media to the 3COM 3C590 network adapter. 3 Log onto Windows NT4 Workstation with administrator privileges (Contact your network administrator if you do not have the required information). 4 Right-click on the âNetwork Neighborhoodâ icon and select âPropertiesâ. 5 Click on âYesâ when prompted to install Windows NT Networking. 6 Select âWired to the networkâ and click on âNextâ. 7 Click on the âSelect from listâ¦â button and then the âHave Diskâ¦â button. Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8 Interrupt 05 05 05 I/O Address 300 300 300
7 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Connecting to a Novell NetWare 3.12 Server 8 Insert the 3COM driver disk into the floppy drive. 9 Set the path to âA:\NDIS\WINNT35\â in the dialog-box and click on âOKâ. 10 Choose by highlighting the â3Com EtherLink III PCI Bus-Master Adapter (3C590)â and click on âOKâ. 11 With â3Com EtherLink III PCI Bus-Master Adapter (3C590)â listed in the âNetwork Adaptersâ window, click on âNextâ. 12 Select the applicable network protocols and click on âNextâ (Contact your network administrator if you do not have the required information). 13 At the âNetwork Services:â prompt, accept default settings and click on âNextâ. 14 Click on âNextâ to continue the network card installation. 15 Set the path to âD:\I386â (D:\ represents the CD-ROM drive with the Windows NT4 Workstation CD) in the dialog box and click on âOKâ. 16 At the âShow Bindings for:â prompt, accept the default settings and click on âNextâ. 17 Click on âNextâ to start the network. 18 Specify your Computer Name, Workgroup or Domain (Contact your network administrator if you do not have the required information) and click on âNextâ. 19 Click on âFinishâ to complete the installation. 20 Remove the driver disk from the floppy drive and select âYesâ at the prompt to shut down and restart your computer for the new settings to take effect. 21 Log onto Windows NT4 Workstation with administrator privileges. 22 From the location of the âNovell IntranetWare Client v.4.11bâ installation files, execute âSetupnw.exeâ. 23 Click on âContinueâ to continue with the Novell IntranetWare Client installation. 24 Click on âYesâ to agree to the Software License Agreement to begin installation. 25 Click on the âRebootâ button at the completion of the Novell NetWare Client installation to restart the machine for changes to take effect. 26 Click on the âIntranetWareâ tab of the Novell IntranetWare Client Services Login screen. 27 Select âBindery Loginâ and specify the Server Name (Contact your network administrator if you do not have the required information). 28 Click on the âLoginâ tab and specify your Name and Password to login.
7 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Connecting to a Novell NetWare 3.12 Server 29 Install the Windows NT4 Service Pack 4 application to correct the error messages in the Event Viewer. 30 Install the Hewlett-Packard Soft Power Down application once the Service Pack 4 has been installed.
8 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows NT 4.0 Workstation 8 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows NT 4.0 Workstation Connecting to a Novell NetWare 4.11 Server Requirements ⢠HP Vectra with Windows NT 4.0 Workstation. ⢠3COM Etherlink III 3C590 PCI 10BT network adapter and driver disk ver- sion 5.2.2. ⢠Driver File: EL59X.SYS, version 1.22 ⢠Microsoft Windows NT 4.0 Workstation media. ⢠Microsoft Windows NT 4.0 Service Pack 4. ⢠Novell NetWare 4.11 Server system that supports IPX network protocol. ⢠Novell IntranetWare Client for Windows NT v4.11b installation media. Device Configuration Procedure 1 With the HP Vectra turned off, install the 3COM 3C590 network adapter into a PCI slot. 2 Connect network cable media to the 3COM 3C590 network adapter. 3 Log onto Windows NT4 Workstation with administrator privileges (Contact your network administrator if you do not have the required information). 4 Right-click on the âNetwork Neighborhoodâ icon and select âPropertiesâ. 5 Click on âYesâ when prompted to install Windows NT Networking. 6 Select âWired to the networkâ and click on âNextâ. 7 Click on the âSelect from listâ¦â button and then the âHave Diskâ¦â button. Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8 Interrupt 05 05 05 I/O Address 300 300 300
8 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Connecting to a Novell NetWare 4.11 Server 8 Insert the 3COM driver disk into the floppy drive. 9 Set the path to âA:\NDIS\WINNT35\â in the dialog-box and click on âOKâ. 10 Choose by highlighting the â3Com EtherLink III PCI Bus-Master Adapter (3C590)â and click on âOKâ. 11 With â3Com EtherLink III PCI Bus-Master Adapter (3C590)â listed in the âNetwork Adaptersâ window, click on âNextâ. 12 Select the applicable network protocols and click on âNextâ (Contact your network administrator if you do not have the required information). 13 At the âNetwork Services:â prompt, accept default settings and click on âNextâ. 14 Click on âNextâ to continue the network card installation. 15 Set the path to âD:\I386â (D:\ represents the CD-ROM drive with the Windows NT4 Workstation CD) in the dialog box and click on âOKâ. 16 At the âShow Bindings for:â prompt, accept the default settings and click on âNextâ. 17 Click on âNextâ to start the network. 18 Specify your Computer Name, Workgroup or Domain (Contact your network administrator if you do not have the required information) and click on âNextâ. 19 Click on âFinishâ to complete the installation. 20 Remove the driver disk from the floppy drive and select âYesâ at the prompt to shut down and restart your computer for the new settings to take effect. 21 Log onto Windows NT4 Workstation with administrator privileges. 22 From the location of the âNovell IntranetWare Client v.4.11bâ installation files, execute âSetupnw.exeâ. 23 Click on âContinueâ to continue with the Novell IntranetWare Client installation. 24 Click on âYesâ to agree to the Software License Agreement to begin installation. 25 Click on the âRebootâ button at the completion of the Novell NetWare Client installation to restart the machine for changes to take effect. 26 Click on the âIntranetWareâ tab of the Novell IntranetWare Client Services Login screen. 27 Select âNDS Loginâ and specify the Tree, Server Name, etc. (Contact your network administrator if you do not have the required information). 28 Click on the âLoginâ tab and specify your Name and Password to login.
8 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Connecting to a Novell NetWare 4.11 Server 29 Install the Windows NT4 Service Pack 4 application to correct the error messages in the Event Viewer. 30 Install the Hewlett-Packard Soft Power Down application once the Service Pack 4 has been installed.
9 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows NT3.51 Workstation 9 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows NT3.51 Workstation Connecting to a Windows NT 3.51 Server Requirements ⢠HP Vectra with Windows NT 3.51 Workstation. ⢠3COM Etherlink III 3C590 PCI 10BT network adapter and driver disk ver- sion 5.2.2. ⢠Driver File: EL59X.SYS, version 1.22 ⢠Microsoft Windows NT 3.51 Workstation media. ⢠Microsoft Windows NT 3.51 Service Pack 5 media. ⢠Microsoft Windows NT 3.51 Server system that supports NetBEUI, NWLink IPX/SPX Compatible Transport and NWLink NetBIOS network protocols. Device Configuration Procedure 1 With the HP Vectra turned off, install the 3COM 3C590 network adapter into a PCI slot. 2 Connect network cable media to the 3COM 3C590 network adapter. 3 Log into Windows NT with administrator privileges. 4 Open the âNetworkâ icon in the âControl Panelâ program group. 5 Click on âYESâ in the âNetwork Settingsâ dialog box to install Windows NT Networking. 6 Insert the Windows NT 3.51Workstation CD in the CD-ROM drive. 7 Set the path to âD:\I386â (D:\ represents the CD-ROM drive with the Windows NT 3.51 CD) in the dialog-box of the Windows NT Setup window and click on âContinueâ. Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8 Interrupt 10 05 05 I/O Address 300 300 300
9 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Connecting to a Windows NT 3.51 Server 8 Click on the âDo Not Detectâ button from the âNetwork Adapter Card Detectionâ window, and click on the âContinueâ button in the following âNetwork Adapter Card Detectionâ window. 9 From the âDrop Down Listâ, scroll down and select â<Other> Requires disk from manufacturerâ, then click on âContinueâ. 10 Set the path to âA:\NDIS\WINNT35\â in the âInsert Diskâ dialog box, and then insert the 3COM âEtherDisk for the Fast EtherLink and EtherLink III Bus Master Adaptersâ diskette in the floppy drive and click âOKâ. 11 Select â3COM Fast Etherlink PCI Bus-Master Adapter (3C590)â in the âSelect OEM Optionâ dialog box, and click âOKâ. 12 Choose the appropriate network protocols by clicking the check boxes in the âWindows NT Setupâ dialog box and click on the âContinueâ button (Contact your network administrator if you do not have the required information). 13 Press âOKâ to continue from âNetwork Settingsâ dialog box. 14 If applicable, press âOKâ to continue from âNWLink IPX/SPX Protocol Configurationâ dialog box. 15 At the âDomain/Workgroup Settingsâ dialog box, click on âOKâ to accept the default âWorkgroupâ as your workgroup name. 16 To complete the installation, remove the floppy disk, and click on âRestart computerâ in the âWindows NT Workstation Networking Setupâ dialog box. 17 Install the Windows NT3.51 Service Pack 5 application.
10 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows NT 3.51 Workstation 10 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows NT 3.51 Workstation Connecting to a Windows NT 4.0 Server Requirements ⢠HP Vectra with Windows NT 3.51 Workstation. ⢠3COM Etherlink III 3C590 PCI 10BT network adapter and driver disk ver- sion 5.2.2. ⢠Driver File: EL59X.SYS, version 1.22 ⢠Microsoft Windows NT 3.51 Workstation media. ⢠Microsoft Windows NT 3.51 Service Pack 5 media. ⢠Microsoft Windows NT 4.0 Server system that supports NetBEUI, NWLink IPX/SPX Compatible Transport and NWLink NetBIOS network protocols. Device Configuration Procedure 1 With the HP Vectra turned off, install the 3COM 3C590 network adapter into a PCI slot. 2 Connect network cable media to the 3COM 3C590 network adapter. 3 Log into Windows NT with administrator privileges. 4 Open the âNetworkâ icon in the âControl Panelâ program group. 5 Click on âYESâ in the âNetwork Settingsâ dialog box to install Windows NT Networking. 6 Insert the Windows NT 3.51Workstation CD in the CD-ROM drive. 7 Set the path to âD:\I386â (D:\ represents the CD-ROM drive with the Windows NT 3.51 CD) in the dialog-box of the Windows NT Setup window and click on âContinueâ. Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8 Interrupt 10 05 05 I/O Address 300 300 300
10 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Connecting to a Windows NT 4.0 Server 8 Click on the âDo Not Detectâ button from the âNetwork Adapter Card Detectionâ window, and click on the âContinueâ button in the following âNetwork Adapter Card Detectionâ window. 9 From the âDrop Down Listâ, scroll down and select â<Other> Requires disk from manufacturerâ, then click on âContinueâ. 10 Set the path to âA:\NDIS\WINNT35\â in the âInsert Diskâ dialog box, and then insert the 3COM âEtherDisk for the Fast EtherLink and EtherLink III Bus Master Adaptersâ diskette in the floppy drive and click âOKâ. 11 Select â3COM Fast Etherlink PCI Bus-Master Adapter (3C590)â in the âSelect OEM Optionâ dialog box, and click âOKâ. 12 Choose the appropriate network protocols by clicking the check boxes in the âWindows NT Setupâ dialog box and click on the âContinueâ button (Contact your network administrator if you do not have the required information). 13 Press âOKâ to continue from âNetwork Settingsâ dialog box. 14 If applicable, press âOKâ to continue from âNWLink IPX/SPX Protocol Configurationâ dialog box. 15 At the âDomain/Workgroup Settingsâ dialog box, click on âOKâ to accept the default âWorkgroupâ as your workgroup name. 16 To complete the installation, remove the floppy disk, and click on âRestart computerâ in the âWindows NT Workstation Networking Setupâ dialog box. 17 Install the Windows NT3.51 Service Pack 5 application.
11 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows NT 3.51 Workstation 11 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows NT 3.51 Workstation Connecting to a Novell NetWare 4.11 Server Requirements ⢠HP Vectra with Windows NT3.51 Workstation. ⢠3COM Etherlink III 3C590 PCI 10BT network adapter and driver disk ver- sion 5.2.2. ⢠Driver File: EL59X.SYS, version 1.22 ⢠Microsoft Windows NT 3.51 Workstation media. ⢠Microsoft Windows NT 3.51 Service Pack 5 media. ⢠Novell NetWare 4.11 Server system that supports IPX network protocol. ⢠Novell IntranetWare Client for Windows NT v4.11b installation media. Device Configuration Procedure 1 With the HP Vectra turned off, install the 3COM 3C590 network adapter into a PCI slot. 2 Connect network cable media to the 3COM 3C590 network adapter. 3 Log into Windows NT with administrator privileges. 4 Open the âNetworkâ icon in the âControl Panelâ program group. 5 Click on âYESâ in the âNetwork Settingsâ dialog box to install Windows NT Networking. 6 Insert the Windows NT 3.51Workstation CD in the CD-ROM drive. 7 Set the path to âD:\I386â (D:\ represents the CD-ROM drive with the Windows NT 3.51 CD) in the dialog-box of the Windows NT Setup window and click on âContinueâ. Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8 Interrupt 10 05 05 I/O Address 300 300 300
11 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Connecting to a Novell NetWare 4.11 Server 8 Click on the âDo Not Detectâ button from the âNetwork Adapter Card Detectionâ window, and click on the âContinueâ button in the following âNetwork Adapter Card Detectionâ window. 9 From the âDrop Down Listâ, scroll down and select â<Other> Requires disk from manufacturerâ, then click on âContinueâ. 10 Set the path to âA:\NDIS\WINNT35\â in the âInsert Diskâ dialog box, and then insert the 3COM âEtherDisk for the Fast EtherLink and EtherLink III Bus Master Adaptersâ diskette in the floppy drive and click âOKâ. 11 Select â3COM Fast Etherlink PCI Bus-Master Adapter (3C590)â in the âSelect OEM Optionâ dialog box, and click âOKâ. 12 Choose the appropriate network protocols by clicking the check boxes in the âWindows NT Setupâ dialog box and click on the âContinueâ button (Contact your network administrator if you do not have the required information). 13 Press âOKâ to continue from âNetwork Settingsâ dialog box. 14 If applicable, press âOKâ to continue from âNWLink IPX/SPX Protocol Configurationâ dialog box. 15 At the âDomain/Workgroup Settingsâ dialog box, click on âOKâ to accept the default âWorkgroupâ as your workgroup name. 16 To complete the installation, remove the floppy disk, and click on âRestart computerâ in the âWindows NT Workstation Networking Setupâ dialog box. 17 Insert the Novell IntranetWare Client v.4.11 application CD in the CD- ROM drive and execute âSetupnw.exeâ. 18 Click on the âContinueâ button to proceed with the installation of the Novell IntranetWare Client. 19 Click on the âRebootâ button to restart the machine for the changes to take effect. 20 Install the Windows NT3.51 Service Pack 5 application.
12 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows for Workgroups 3.11 12 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows for Workgroups 3.11 Connecting to a Windows NT 4.0 Server Requirements ⢠HP Vectra with MS-DOS and MS-Windows for Workgroups 3.11 ⢠3COM Etherlink III 3C590 PCI 10BT network adapter and driver disk ver- sion 5.2.2. ⢠Driver File: EL59X.386, version 1.18 ⢠Microsoft Windows for Workgroups 3.11 media. ⢠Microsoft Windows NT 4.0 Server system that supports NetBEUI, NWLink IPX/SPX Compatible Transport and NWLink NetBIOS network protocols. ⢠Device Configuration Procedure 1 With the HP Vectra turned off, install the 3COM 3C590 network adapter into a PCI slot. 2 Connect network cable media to the 3COM 3C590 network adapter. 3 After Windows loads, open the âNETWORKâ Program Group, and double- click on âNetwork Setupâ. 4 Click on the âNetworksâ button in the âNetwork Setupâ dialog box. 5 Click on the âInstall Microsoft Windows Network:â option, and click âOKâ. 6 Click on the âDriversâ button from the âNetwork Setupâ dialog box, and click on âAdd Adapterâ. 7 Click âOKâ to accept the default choice of âUnlisted or Updated Network Adapterâ. 8 Type the path âA:\NDIS\WFWâ in the âInstall Driverâ dialog box, and then insert the 3COM 3C590 driver disk into the floppy drive, and click âOKâ. Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8 Interrupt 05 05 05 I/O Address 300 300 300
12 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Connecting to a Windows NT 4.0 Server 9 Select â3COM Fast EtherLink/EtherLink III Bus Master Adapter (3C59X)â in the âUnlisted or Updated Network Adapterâ dialog box, and click âOKâ. 10 Make sure that the â3COM Fast EtherLink/EtherLink III Bus Master Adapter (3C59X)â is selected in âNetwork Driversâ. 11 Accept the applicable network protocols, and then click on âCLOSEâ. 12 At the âNetwork Setupâ dialog box, click on âOKâ. 13 Specify your User Name, Workgroup, and Computer Name in âMicrosoft Windows Network Namesâ dialog box, and click on âOKâ. (The Drivers will now start to copy). 14 To complete the installation, remove the Intel diskette from the floppy drive and click on âRestart Computerâ button in the âWindows Setupâ dialog box.
13 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows for Workgroups 3.11 13 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Microsoft Windows for Workgroups 3.11 Connecting to a Novell NetWare 4.11 Server Requirements ⢠HP Vectra with DOS and MS-Windows for Workgroups 3.11. ⢠3COM Etherlink III 3C590 PCI 10BT network adapter and driver disk ver- sion 5.2.2. ⢠Driver File: EL59X.386, version 1.18 ⢠Microsoft Windows for Workgroups 3.11 media. ⢠Novell NetWare 4.11 Server system that supports IPX network protocol. ⢠NetWare Client for DOS and MS Windows v1.21 installation media. Device Configuration Procedure 1 With the HP Vectra turned off, install the 3COM 3C590 network adapter into a PCI slot. 2 Connect network cable media to the 3COM 3C590 network adapter. 3 From the location of the âNetWare Client for DOS and Windows v1.21â installation files, execute âInstall.exeâ. 4 Select option 5 âSelect the driver for your network boardâ and press âEnterâ. 5 Select âOTHER DRIVERSâfrom the Network Board selection. 6 Insert the 3COM 3C590 driver disk into the floppy drive. 7 Type the path âA:\NETWARE\CLIENTâ when prompted and press âEnterâ. 8 Select â3Com Fast EtherLink/EtherLink III Bus Master Familyâ and hit âEnterâ. Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8 Interrupt 05 05 05 I/O Address 210 300 300
13 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter Connecting to a Novell NetWare 4.11 Server 9 Accept the default network board settings and press âF10â to save it. 10 Select option 6 âHighlight here and press <Enter> to installâ and press âEnterâ to begin installation. 11 When the installation is finished, remove the 3COM 3C590 driver disk from the floppy drive and press <CTR><ALT><DEL> to restart the system. 12 You may login to a server from the DOS prompt or load Windows for Workgroup v3.11 and use the âNetWare User Toolsâ from the NetWare Tools folder to login to a server. (If you do not have the required information, contact your network administrator).