HP D2847A User Manual
21-inch Color Monitor 19.8-inch V iewable Image User´s Guide 21-Zoll-Farbbildschirm 19,8 Zoll-Bildanzeige Benutzerhandbuch Moniteur couleur 21 pouces Affichage 19,8 pouces Guide de l´utilisateur Pantalla de color de 21 pulgadas 19,8 pulgadas de imagen visualizada Manual del Usario V ideo a colori da 21 pollici Immagine visibile da 19,8 pollici Manuale dell´utente Monitor Colorido de 21 polegadas Imagem V isìvel de 19,8 polegadas Guia do Usuário HP D2847 P 111 0 PLUG PLA Y &
Notice The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by Hewlett-Packard. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of Hewlett- Packard Company . ® FD T rinitron is a registered trademark of Sony corporation. Hinweis Inhaltliche Ãnderungen vorbehalten. Hewlett-Packard übernimmt keine Garantie welcher Art auch immer für diese Ausrüstung, einschlieÃlich der (doch nicht begrenzt auf die) Qualitätsgarantie und die Garantie bezüglich Eignung für einen bestimmten Zweck. Hewlett-Packard haftet nicht für in dieser Dokumentation enthaltene Fehler oder für unbeabsichtigte oder indirekte Schäden in Verbindung mit der Lieferung, der Leistung oder der Benutzung der Ausrüstung. Hewlett-Packard übernimmt keine Haftung fur den Betrieb oder die Zuverlässigkeit seiner Software, wenn diese auf Hardware benutzt wird, die nicht von Hewlett-Packard geliefert wurde. Dieses Dokument enthalt proprietäre Informationen, die durch das Copyright geschützt sind. Alle Rechte vorbehalten. Dieses Dokument darf ohne vorherige schriftliche Genehmigung der Hewlett-Packard Company weder ganz noch teilweise fotokopiert, reproduziert oder übersetzt werden. ® FD Triniton ist die registrierte Handelsmarke der Sony Corporation. Avertissement Les informations contenues dans ce document peuvent être modifiées sans préavis. Hewlett-Packard ne donne aucune garantie de quelque sorte que ce soit concernant, sans que ce soit limitatif, les garanties implicites de qualité commerciale de ce matériel, ou la bonne adaptation de celui-ci à un usage particulier. Hewlett-Packard nâest pas responsable des erreurs pouvant apparaître dans ce manuel et nâest pas non plus responsable des dommages directs ou indirects résultant de lâéquipement, des performances et de lâutilisation de ce matériel. Hewlett-Packard ne saurait être tenu pour responsable de lâutilisation et de la fiabilité de son logiciel sur des matériels non fournis par Hewlett-Packard. Les informations contenues dans ce document sont originales et protégées par copyright. T ous droits réservés. L âacheteur sâinterdit en conséquence de les photocopier, de les reproduire ou de les traduire dans toute autre langue, sauf accord préalable et écrit de Hewlett-Packard. ® FD Trinitron est une marque déposée de Sony Corporation. Aviso La información contenida en este documento está sujeta a cambios sin previo aviso. Hewlett-Packard no ofrece ningún tipo de garantÃa con respecto a este material, incluyendo, pero sin limitarse a, las garantÃas implÃcitas de comerciabilidad e idoneidad para un fin determinado. Hewlett-Packard no asume responsabilidad alguna por los posibles errores contenidos o por los daños casuales o emergentes relacionados con el suministro, funcionamiento o uso de este material. Hewlett-Packard no asume responsabilidad alguna por el uso o fiabilidad de su software en equipos que no hayan sido fabricados por Hewlett-Packard. Este documento contiene información patentada, protegida por las leyes del copyright. Reservados todos los derechos. Ninguna parte de este documento puede ser fotocopiada, reproducida o traducida a otro idioma sin la autorización previa y por escrito de Hewlett-Packard Company . ® FD T rinitron es una marca registrado de Sony Corporation. Avviso Le informazioni contenute in questo documento sono soggette a cambiamento senza preavviso. Hewlett-Packard non rilascia garanzie di alcun tipo riguardo a questo materiale, comprese le garanzie implicite di commerciabilità e di idoneità per uno scopo particolare. Hewlett-Packard non sarà ritenuta responsabile per errori contenuti in questo documento, né per danni accidentali o conseguenti alla fornitura, alle prestazioni o allâuso di questo materiale. Hewlett-Packard non si assume alcuna responsabilità riguardo allâuso o allâaffidabilità del proprio software su apparecchiature di altri produttori. Questo documento contiene informazioni di proprietà protette da copyright. Tutti i diritti sono riservati. Nessuna parte di questo documento può essere fotocopiata, riprodotta o tradotta in unâaltra lingua senza un precedente consenso scritto di Hewlett-Packard Company . ® FD Trinitron è un marchio del mestiere di Società per azioni di Sony . Nota As informações contidas neste documento estão sujeitas a alteração sem notificação prévia. A Hewlett-Packard não oferece nenhum tipo de garantia com relação a este material, incluindo, mas não limitada à s, garantias implÃcitas de comercialização e conveniência para um propósito especÃfico. A Hewlett-Packard não será responsável por erros aqui contidos ou por danos incidentais ou conseqüenciais relacionados ao fornecimento, desempenho ou utilização deste material. A Hewlett-Packard não se responsabiliza pelo uso ou confiabilidade se seu software em equipamentos que não sejam fornecidos pela Hewlett-Packard. Este documento contém informações proprietárias protegidas por direitos autorais. T odos os direitos são reservados. Nenhuma parte deste documento pode ser fotocopiada, reproduzida ou traduzida para outro idioma sem o consentimento prévio por escrito da Hewlett-Packard Company . ® FD Trinitron é uma marca comercial da Sony Corporation. Hewlett-Packard France 38053 Grenoble Cedex 9 France © 1999 Hewlett-Packard Company
1 HP D2847A, HP D2847W 21-inch Color Monitors 19.8-inch V iewable Image User â s Guide 0.25 mm dot pitch for excellent graphics FD T rinitron®, anti-glare, anti- static, multilayer screen coating Image adjustment controls to operate on-screen display menus Status indicator Full scan screen that gives an edge to edge image On/Off switch
HP 21" Color Monitor Userâs Guide 2 English Important Safety Instructions Important Safety Instructions Before you plug in your new monitor, read these important safety instructions. For your safety always connect equipment to a grounded wall outlet. Always use a power cord with a properly grounded plug, such as the one provided with the equipment, or one in compliance with your national safety standards. This equipment can be disconnected from the power by removing the power cord from the power outlet. This means the equipment must be located close to an easily accessible power outlet. T o avoid electrical shock, do not open the monitor â s cover . There are no user- serviceable parts inside. Only qualified service personnel should service these parts. Make sure your PC is powered off before connecting or disconnecting a display peripheral. Thank you for selecting HP monitor equipment. T o optimize your comfort and productivity , itâ s important that you set up your work area correctly and use your HP equipment properly . W ith that in mind, we have developed some set-up and use recommendations for you to follow based on estab- lished ergonomic principles. Y ou can consult the online version of W orking in Comfort preloaded on the hard disk of HP computers, or visit HPâ s W orking in Comfort web site at: http://www .hp.com/ergo/ The monitor is quite heavy (the weight is shown in the technical specifications). W e recommend you ask the assistance of a second person when lifting or moving it. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated âdangerous voltageâ within the productâ s enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompa- nying the appliance. W ARNING CAUTION WORKING IN COMFORT
HP 21" Color Monitor Userâs Guide English 3 What Y our New Monitor Of fers Y our HP monitor is a FD T rinitron 21-inch (19.8-inch viewable image), high resolution, multi-synchronous color monitor . Multi-synchronous means that the monitor supports a range of video modes. It is optimized to be used with all Hewlett-Packard computers. Y our HP color monitor has the following features: ⢠A 21-inch FD T rinitron tube, with a 19.8-inch viewable image, and 0.25 mm dot pitch for excellent graphics. Anti-glare, multilayer coating to minimize reflection. ⢠Support of video modes up to 1600 x 1200 at 85 Hz refresh rates, and up to 1800 x 1440 using a 80 Hz refresh rate. ⢠Image adjustment using on-screen display menus. Includes color adjustment and image manipulation controls to optimize the quality and position of the image. ⢠Improved color matching using the sRGB color temperature profile: this can significantly improve color matching with other system devices (printer, computer software, scanner, etc) using sRGB standard color space. ⢠Monitor power management system (VESA 1 standard) controlled from suitably equipped HP computers to automatically reduce the power consumption of the monitor . As an ENERGY ST AR 2 partner , HP has determined that this product meets the ENERGY ST AR guidelines for energy ef ficiency ⢠Monitor Plug and Play capability (VESA DDC1/2Bi standard) that enables the monitor to identify itself to suitably equipped HP computers. ⢠Compliance with ISO 9241-3/-7/-8 ergonomic standards. ⢠Complies with MPRIII, level A guidelines for upper limits of electrical and electrostatic emissions, from the Swedish National Board for Measurement and T esting. ⢠Y our HP monitor complies with TCO99 requirements, refer to the last pages of this manual for more information. 1 VESA is the Video Electronics Standards Association 2 ENERGY ST AR is trademark of United States Environmental Protection Agency (EP A ) What Y our New Monitor Offers
HP 21" Color Monitor Userâs Guide 4 English Setting Up Y our Monitor Where to Place the Monitor Place your monitor on a flat sturdy surface. Ensure the operating site is free from excessive heat, moisture, and sources of electromagnetic fields. Sources of electromagnetic fields include transformers, motors, and other monitors. Connecting the Cables 1 Before you connect any cables, refer to the safety instructions at the beginning of this manual. Make sure your computer and monitor are switched off. 2 Connect the video cable (it has a 15-pin plug) to the video outlet on your com- puter . T ighten the thumbscrews on the plug. 3 Connect the power cord to the monitor . 4 Plug the power cord into the power outlet. Video cable The location of your computer â s video cable connector may be different to the one shown. Refer to the manual that came with your computer , if necessary . Setting Up Y our Monitor Power cords NOTE
HP 21" Color Monitor Userâs Guide English 5 Using Y our Monitor Using Y our Monitor 1 Press the power switch to turn the monitor on or off. 2 When the power is turned on, the power-on indicator will light up. The light indicates the operating state: ⢠Green: The monitor is in normal operation. ⢠Blinking: The monitor is in the active off state. ⢠Off: The monitor is turned off at the power switch or disconnected from the mains outlet. If the power management function of your computer is working properly , you do not need to switch the monitor off or on. This occurs automatically . Pressing the button activates the monitor â s on-screen menu. This menu contains the monitor â s various adjustment features. Select a feature using the and buttons. Scroll to the adjustment feature you require and then press to access the menu. T o adjust the required feature, use the and buttons until the desired changes are complete. Menu language 1 When you press the button for the first time , the Menu language menu appears on the screen. 2 Select a language with the and buttons and press the button to activate your choice.
HP 21" Color Monitor Userâs Guide 6 English 5 Select the adjustment with the and buttons. 6 Press to confirm the selection. The menu disappears and a scale shows the position of the adjustment. In addition to the bar, position of the adjustment is shown as a percentage of the maximum value. The upper number shows the current value and the lower one shows the value where the adjustment started. SIZE & POSITION SHAPE SHARPNESS COLOR MISCELLANEOUS CONTRAST BRIGHTNESS TIL T 4 SIZE & POSITION SHAPE SHARPNESS COLOR MISCELLANEOUS CONTRAST BRIGHTNESS HORIZONT AL CENTERING 1 2 3 Using Y our Monitor Using the menu Menu operations are controlled with the , and buttons. 1 Y ou can display the menu by pressing the button. 2 Select the header with the and buttons. 3 Press to confirm the selection. 4 Adjustment and settings corresponding the header appear below the header field. CONTRAST BRIGHTNESS TIL T OR THOGONALITY TRAPEZOID PINCUSHION PINCUSHION BALANCE EXIT 1280 X 1024 85 Hz 5 6
HP 21" Color Monitor Userâs Guide English 7 TIL T 50 % 77 % 8 7 Using Y our Monitor 7 Adjust with the and buttons. 8 When ready , press the button. Exiting the menu The onscreen menu disappears automatically after 20 seconds of inactivity . Alterna- tively select EXIT and press the button to make the menu disappear immediately . Adjusting the picture of your monitor Y ou should allow the monitor warm up for 20 minutes before making any adjustments to image settings of the monitor . Size and position The illustrations below show the effect of each adjustment when the property is adjusted from the extreme left to the extreme right position. ⢠First correct the property with largest deviation from the correct value then adjust the width and height. 1280 x 1024 85 Hz SIZE & POSITION SHAPE SHARPNESS COLOR MISCELLANEOUS CONTRAST BRIGHTNESS HORIZONT AL CENTERING WIDTH VERTICAL CENTERING HEIGHT PRESET RECALL EXIT Brightness and Contrast With brightness adjustment you may control the brightness of the whole picture. Contrast increases or decreases the brightness difference between light and dark colors. Adjust brightness and contrast adequately according to ambient light conditions to obtain the best picture quality .
HP 21" Color Monitor Userâs Guide 8 English Sharpness SIZE & POSITION SHAPE SHARPNESS COLOR MISCELLANEOUS VERTICAL CONV HORIZONT AL CONV MOIRE COLOR PURITY DEF A UL T SHARPNESS EXIT 1280 x 1024 85 Hz Shape The illustrations below show the effect of each adjustment when the property is adjusted from the extreme left to the extreme right psosition. ⢠When adjusting these properties, set picture width and height so that its edges are visible. Compare the edges of the picture to those of the bezel. ⢠First correct the property with largest deviation from the correct value then adjust the width and height. SIZE & POSITION SHAPE SHARPNESS COLOR MISCELLANEOUS CONTRAST BRIGHTNESS TIL T OR THOGONALITY TRAPEZOID PINCUSHION PINCUSHION BALANCE EXIT 1280 x 1024 85 Hz Preset Recall This function restores the factory defaults and deletes user made settings for: ⢠Size and position ⢠Shape Using Y our Monitor
HP 21" Color Monitor Userâs Guide English 9 V ertical and horizontal convergence A white line on the screen is made up of red, green and blue lines. If there are no convergence errors on the picture, the lines will be exactly overlaid and the resulting color is white. If there is a serious convergence error, separate red, green or blue lines will be seen instead of white. ⢠With Horizontal conv you may minimize the error in vertical lines. ⢠W ith V ertical conv you may minimize the error in horizontal lines. Moire The interference on the screen can be reduced with the help of moire adjustment. Boost the moire adjustment until the interference pattern is acceptable. Moire adjustment slightly reduces picture sharpness. Return the adjustment to zero if there is no risk of moire interference. Using Y our Monitorr Color purity These adjustments can be used to change the color temperature (tint) of the screen. The icon of each adjustment indicates the area on the screen the adjustment affects. COLOR PURITY T OP AND BO TT OM T OP RIGHT BO TTOM RIGHT T OP LEFT BO TTOM LEFT EXIT 1280 x 1024 85 Hz Y ou should allow the monitor to warm up for 20 minutes and demagnetize the monitor before starting the color purity adjustment. Color purity problems do not show up with white test picture. Always use fully red or green test picture. Default sharpness This function restores the factory defaults and deletes user made settings for: ⢠V ertical conv , Horizontal conv , Moire, Color purity NOTE
HP 21" Color Monitor Userâs Guide 10 English 1280 x 1024 85 Hz SIZE & POSITION SHAPE SHARPNESS COLOR MISCELLANEOUS CONTRAST BRIGHTNESS COLOR TEMP 9300 K RED GREEN BLUE SA VE T O CUSTOM 1 EXIT Color With the Color menu the user may adjust the tint of the screen. Color temperature The user can choose between the following fixed color temperatures: ⢠5000K, 6000K, 6500K, 7000K, 8000K, 9300K, 10000K Alternatively , a user specified profile can be selected: ⢠CUSTOM1 User definable color temperature, refer to the chapter âSave to Customâ ⢠sRGB sRGB stands for âstandardized Red, Green and Blueâ colour space. Selecting sRGB means that the monitor displays the images with the same colour balance as other system components (scanner, printer,computer software etc) utilizing the same sRGB color standard. After a preset tint has been selected, the color temperature may be adjusted further as desired. Using Y our Monitor Red, Green, Blue Color monitors mix red, green and blue colors to produce required tint. With Red , Green and Blue intensity control you may finetune any preset tint. ⢠After adjusting Red , Green or Blue the word CUSTOM replaces the color temperature indication.
HP 21" Color Monitor Userâs Guide English 11 Using Y our Monitor Miscellaneous SHAPE SHARPNESS COLOR MISCELLANEOUS CONTRAST BRIGHTNESS DEMA GNETIZE LANGU A GE/SPRACHE/LANGUE ABOUT MONIT OR EXIT 1280 x 1024 85 Hz Save to Custom Y ou may save one custom color temperature setting containing individual Red , Gr een and Blue adjustments. T o create a custom color temperature ⢠Adjust the desired tint with Red , Green and Blue . ⢠Step to Save to Custom and store the settings. T o recall a custom color temperature, refer to the section âColor tempâ. 1280 x 1024 85 Hz SIZE & POSITION SHAPE SHARPNESS COLOR MISCELLANEOUS CONTRAST BRIGHTNESS COLOR TEMP CUST OM RED GREEN BLUE SA VE T O CUSTOM 1 EXIT
HP 21" Color Monitor Userâs Guide 12 English Demagnetize External magnetic fields may cause distortion or discoloration in the picture. Degauss- ing, which takes place automatically when the monitor is switched on, normally maintains faultless color purity . If the purity deteriorates during use, for example when the monitor â s position is changed, perform demagnetizing. During the degaussing process the picture is distorted for a few seconds. When the process is completed, any color impurities will disappear caused by stray magnetic fields. The efficiency of the demagnetization decreases if repeated at intervals shorter than 15 minutes. Menu language The language selection affects the menu languages of your monitor . The following languages are available: * LANGU A GE/SPRACHE/LANGUE ENGLISH DEUTSCH ESP AÃOL FRANÃAIS IT ALIANO POR TUGUÃS EXIT 1280 x 1024 85 Hz The active language is marked with an asterisk. About monitor Shows the display properties of the currently used display mode. 1280 x 1024 85 Hz ABOUT MONIT OR CURRENT MODE RESOLUTION HOR. FREQ. VERT . FREQ. SYNCHRONIZA TION HOR. FREQ. VERT . FREQ. EXIT 1280 x 1024 91,15 KHz 85 KHz 29 - 121 KHz 50 - 180 Hz Using Y our Monitor
HP 21" Color Monitor Userâs Guide English 13 What V ideo Modes are Supported Y our monitor comes with the standard modes shown in the table below . It also supports intermediate video modes. With the intermediate modes, the displayed image may need to be optimized using the buttons on the front panel. All modes are non- interlaced. Y our monitor is GTF* compatible. *GTF stands for General Timing Formula. Re s o lu ti o n Re fre s h ra te /Hz 640 x 400 70 640 x 480 60, 85 800 x 600 85 1024 x 768 75, 85 1280 x 1024 75, 85 1600 x 1200 75, 85, G T F 1800 x 1440 80 Minimizing Eye Strain T o avoid screen flicker and minimize eye strain, use the highest supported image refresh rate for the chosen resolution. It is recommended that you use a refresh rate of 85 Hz. The image refresh rate is the number of times per second that the image is refreshed. Minimizing Energy Consumption If your computer supports VESA monitor power management (available on many HP computers), you can minimize the power consumed by the monitor . There are two power saving modes: ⢠Suspend mode 1 (uses less than 10 W). ⢠Active off mode 2 (uses less than 3 W). In this mode, the monitor â s front panel indicator light blinks slowly in green. T o set these power saving modes, refer to the manual that came with your computer . If your screen is not displaying an image, check the front panel indicator light first â your monitor may be in a power saving mode. Using Y our Monitor 1 Suspend mode is activated when vertical sync is cut by the video controller. 2 Active off mode is activated when both vertical and horizontal sync are cut by the video controller.
HP 21" Color Monitor Userâs Guide 14 English T echnical Specifications T echnical Specifications PI C TU RE TU BE Siz e 21- in ch, v i ewable im age si z e 19.8 in ch D o t p i tch 0.2 5 m m Fa ce p l ate FD T ri n i tron , an ti-g l are, a n tis tati c IN TER F ACE Detach abl e Vi deo C able with 15-pin min i D -SU B Con n ector S C A NNI NG F R E Q UE NC Y H oriz on tal 29 to 121 kH z V er tical 50 to 180 H z M AX. RESO LU TI O N (H x V ) 1800x 1440 ( 80H z) W AR M- U P TIM E 30 m in u tes t o reach optim u m perf orman ce lev el PIXEL C LOCK <300 M H z I MAG E SIZE Stan dard six e: 393 (W) x 293 (H ) mm Maxi m u m siz e: 403 (W)x 302 (H ) mm POW ER MA N AGE MEN T On 160 W ( m ax) Con st an t green LED Stan dby m ode 90W (max ) Con s tan t Gr een LED Su spend mod e 10W (max ) Con st an t green LED Activ e O ff 3W (max ) Gr een blin kin g LED Of f 1W (m ax ) LED is Of f POWER SOU RCE AC 90 to 264 V , 50/60 H z Cu rr en t 2 A OP E RA T IN G EN VI RO N M EN T T emperatu re 0°C to 40°C H u m idi ty 10% RH throu gh 80 % RH ( with ou t con den sation ) STO RAGE EN VI RO N M EN T T emperatu re - 20°C to 60°C H u m i di ty 8 % R H th rou gh 85 % RH (wit h ou t con de n sati on ) C A B IN ET D IME N SION S 51 2 (H ) x 502 (W) x 513 (D ) WEIG H T 30.9 kg TI L T&SW IVEL STA N D T ilt an gle -5° t o 15° Swiv el An gle -90° t o 9 0°
HP 21" Color Monitor Userâs Guide English 15 Care and Cleaning, Environmental Information Care and Cleaning Do not place anything on top of the monitor . Doing so may block the monitor vents and cause damage to the monitor due to overheating. Do not let liquid get on or into the monitor . T o maximize screen life and prevent damage to the picture tube (such as burned phosphor due to leaving the same image on the screen for a long time), it is recom- mended that you: ⢠Use the monitor power management system (on HP computers) or a screen saver program. ⢠A void setting contrast and brightness to their maximum levels for prolonged periods. ⢠If you do not have a power management system or a screen saver program, switch the monitor off or reduce the brightness and contrast to minimum levels when the monitor is not in use. Y our monitor has an anti-glare, anti-static screen coating. T o prevent damage to the monitor screenâ s coating, use a regular household glass cleaner when cleaning the screen. T o clean the screen: 1 Switch the monitor off and remove the power plug (pull the plug, not the cable). 2 W et a soft cotton cloth with the cleaning solution and gently wipe the screen. Do not spray cleaner onto the screen because the cleaner may drip inside the monitor . 3 Dry with a clean, soft cotton cloth. Do not use cleaning solutions containing fluoride, acids, or alkalis. Environmental Information HP has a strong commitment toward the environment. Y our HP monitor has been designed to respect the environment as much as possible. HP can also take back your old monitor for recycling when it reaches the end of its useful life. In fact, HP has a product take-back program in several countries. The collected equipment is sent to one of HPâ s recycling facilities in Europe or the USA. As many parts as possible are reused. The remainder is recycled. Special care is taken for batteries and other potentially toxic substances, which are reduced to non-harmful components through a special chemical process. If you require more details about HPâ s product take-back program, contact your dealer or your nearest HP Sales Office. The cathode ray tube used in this monitor does not contain cadmium.
HP 21" Color Monitor Userâs Guide 16 English Hardware Warranty Hardware W arranty P AR T I - HP General Hardware W arranty General This HP Monitor Hardware W arranty Statement gives you, the customer, express warranty rights from HP , the manufacturer. FOR CONSUMER TRANSACTIONS IN AUSTRALIA AND NEW ZEALAND: THE W ARRANTY TERMS CONT AINED IN THIS ST A TEMENT , EXCEPT T O THE EXTENT LA WFULL Y PERMITTED, DO NOT EXCLUDE, RESTRICT OR MODIFY AND ARE IN ADDITION TO THE MANDA TOR Y ST A TUTOR Y RIGHTS APPLICABLE TO THE SALE OF THIS PRODUCT TO YOU. THE LA WS OF YOUR COUNTR Y MA Y PROVIDE FOR DIFFERENT W ARRANTY RIGHTS. IF SO, YOUR AUTHORIZED HP DEALER OR HP SALES AND SER VICE OFFICE CAN PROVIDE YOU WITH DET AILS. W arranty repair or replacement Hewlett-Packard (HP) warrants this monitor hardware product, or accessory against defects in materials and workmanship for the applicable warranty period stated above, commencing from the date of delivery of the product to the end-user customer. HP does not warrant that the HP hardware will operate uninterrupted or error free. If, during the product warranty period, HP is unable, within a reasonable time, to repair or replace your product to the condition as warranted, you will be entitled to a refund (in the amount of the product purchase price) upon prompt return of the product to your authorized HP dealer or other HP designate. Unless otherwise stated or agreed upon in writing with HP , all hardware components must be returned for refund with the entire system process unit. HP software is covered by the HP Software Product Limited W arranty located in your HP product manual. Unless otherwise stated, and to the extent permitted by local law , hardware products may contain remanufactured parts (equivalent to new in performance) or parts which may have been subject to prior incidental use. HP may repair or replace hardware products (i) with products which are equivalent in performance to the products being repaired or replaced but which may have been subject to prior use, or (ii) with products which may contain remanufactured parts equivalent to new in performance or parts which may have been subject to prior incidental use. M odel W ar r ant y Per iod Serv i ce pr ovi ded D2 847A D2 847W 3 y earsâu n less or igi n al en d-u ser cu stom er h as oth erw ise agreed t o a shorte r pe ri od of warra n ty a t th e time of pu rch ase. On-si te s e rvi ce fo r fi rs t y e ar , a n d re tu rn to a n HP or re pa i r-a u th o ri z e d re se l ler s er v i c e- ce nter fo r the fo llo wi ng two ye a r s .
HP 21" Color Monitor Userâs Guide English 17 Hardware Warranty Proof of Purchase and Warranty Period In order to receive service or support for your hardware product for the warranty period, proof of the original purchase date of the product may be required in order to establish the delivery date of your product. If the delivery date is not available, either the purchase date or the manufacturerâs date (located on the product) becomes the beginning of the warranty period. Limitation of Warranty W arranty does not apply to defects resulting from: (a) improper or inadequate maintenance or calibration; (b) software, interfacing, parts or supplies not supplied by HP; (c) unauthorized repair, maintenance, modifica- tion or misuse; (d) operation outside of the published operating specifications for the product; (e) improper site preparation or maintenance; or (f) such other exclusions as may be expressly set forth in this W arranty Statement. HP MAKES NO OTHER EXPRESS W ARRANTY , WHETHER WRITTEN OR ORAL, WITH RESPECT TO THIS PRODUCT . TO THE EXTENT ALLOWED BY APPLICABLE LOCAL LA W , ANY IMPLIED W ARRANTY OF MERCHANT ABILITY OR FITNESS FOR A P AR TICULAR PURPOSE IS LIMITED T O THE DURA TION OF THE EXPRESS W ARRANTY SET FOR TH ABOVE. Limitation of Liability and Remedies TO THE EXTENT ALLOWED BY APPLICABLE LOCAL LA W , THE REMEDIES IN THIS W ARRANTY ST A TEMENT ARE YOUR SOLE AND EXCLUSIVE REMEDIES. IN NO EVENT SHALL HP BE LIABLE FOR LOSS OF DA T A OR FOR DIRECT , INDIRECT , SPECIAL, INCIDENT AL, OR CONSEQUENTIAL DAMAGE, WHETHER BASED ON W ARRANTY CONTRACT , TOR T , OR ANY OTHER LEGAL THEOR Y . The foregoing limitation of liability shall not apply in the event that any HP product sold hereunder is determined by a court of competent jurisdiction to be defective and to have directly caused bodily injury , death, or property damage. T o the extent allowed by applicable local law , HPâ s liability for property damage does not exceed the greater of $50,000 or the purchase price of the specific product that caused such damage. P AR T II - Y ear 2000 W arranty Subject to all of the terms and limitations of the HP Limited W arranty Statement provided with this HP Product, HP warrants that this HP Product will be able to accurately process date data (including, but not limited to, calculating, comparing, and sequencing) from, into, and between the twentieth and twenty-first centuries, and the years 1999 and 2000, including leap year calculations, when used in accordance with the Product documentation provided by HP (including any instructions for installing patches or upgrades), provided that all other products (e.g. hardware, software, firmware) used in combination with such HP Product(s) properly exchange date data with it. The duration of the Y ear 2000 warranty extends through January 31, 2001.
HP 21" Color Monitor Userâs Guide 18 English Declaration of Conformity Manufacturerâs Name: HEWLETT-P ACKARD France Manufacturerâs Address: 5 , Avenue Raymond Chanas - EYBENS 38053 GRENOBLE CEDEX 09 -FRANCE declares, that the products: Product Name: 21-inch Color Monitor Model Number: D2847 * (*can be blank or any alpha-numeric charater) conform(s) to the following Product Specifications: SAFETY International: IEC 60950:1991 A1 A2 A3 A4 / GB4943-1995 Europe: EN 60950:1992 A1 A2 A3 A4 EMC CISPR 22:1993 A1 A2 / EN 55022:1994 A1 A2 Class B 1) EN 50082-1:1992 IEC 801-2:1992 / prEN 55024-2:1992 - 4kV CD, 8 kV AD IEC 801-3:1984 - 3V/m IEC 801-4:1988 / prEN 55024-4:1992 - 1 kV Power Lines IEC 555-2:1982 A1:1985 / EN 60555-2:1987 IEC 61000-3-3:1994 / EN 61000-3-3:1995 GB9254-1988 FCC Title 47 CFR, Part 15 class B 2) ICES-003, Issue 2 VCCI-B AS/NZ 3548:1992 Supplementary information: The product herewith complies with the requirements of the following Directives and carries the CE mark accordingly: the EMC Directive 89/336/EEC, the Low Voltage Directive 73/23/EEC both amended by the Directive 93/68/EEC. 1) The product was tested in a typical configuration with Hewlett-Packard Personal Computer systems. 2) This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Jean Marc JULIA Grenoble, August 1999 Quality Manager For Compliance Information ONL Y , contact: USA contact: Hewlett-Packard Company , Corporate Product Regulations Manager , 3000 Hanover Street, Palo Alto, CA 94304. (Phone 1 (415) 857-1501). DECLARA TION OF CONFORMITY according to ISO/IEC Guide 22 and EN 45014 Declaration of Conformity
HP 21" Color Monitor Userâs Guide English 19 Regulatory Information Notice for the USA: FCC Class B Statement Federal Communications Commission Radio Frequency Interference Statement Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one or more of the following measures: ⢠Reorient or relocate the receiving antenna. ⢠Increase the distance between the equipment and the receiver. ⢠Connect the equipment to an outlet on a different circuit to the one the receiver is connected to. ⢠Consult your dealer or an experienced radio/TV technician for help. Hewlett-Packard's FCC Compliance T ests were conducted using HP-supported peripheral devices and HP shielded cables, such as those you receive with your system. Changes or modifications not expressly approved by Hewlett-Packard could void the user's authority to operate the equipment. Notice for Canada This Class âBâ digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la Classe B respecte toutes les exigences du règlement sur le matériel brouilleur du Canada. X-Ray Radiation Notice When operating, this product emits x-rays; however, it is well shielded and meets the safety and health requirements of various countries, such as the Radiation Act of Germany and the Radiation Control for Health and Safety Act of the United States. Radiation emitted by this product is less than 0.1 mR/hr (1uSv/hr) at a distance of 10 centimeters from the surface of the cathode ray tube. The x-ray radiation primarily depends on the characteristics of the cathode ray tube and its associated low voltage and high voltage circuitry . Internal controls have been adjusted to ensure safe operation. Only qualified personnel should perform any internal adjustments as specified in the service manual for this product. Replace the cathode ray tube with an identical CR T only . Safety W arning for USA If the power cord is not supplied with your monitor, select the proper power cord according to your national electric safety codes. ⢠USA: use a UL listed detachable power cord.
HP 21" Color Monitor Userâs Guide 20 English Notice for Japan Regulatory Information Notice for Korea
HP 21" Color Monitor Userâs Guide English 21 Congratulations! Y ou have just purchased a TCOâ99 approved and labelled product! Y our choice has provided you with a product developed for professional use. Y our purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products. Why do we have environmentally labeled computers? In many countries, environmental labeling has become an established method for encouraging the adaptation of goods and services to the environment. The main problem, as far as computers and other electronics equipment are concerned, is that environmentally harmful substances are used both in the products and during their manufacture. Since it is not so far possible to satisfactorily recycle the majority of electronics equipment, most of these potentially damaging substances sooner or later enter nature. There are also other characteristics of a computer, such as energy consumption levels, that are important from the viewpoints of both the work (internal) and natural (external) environments. Since all methods of electricity generation have a negative effect on the environment (e.g. acidic and climate-influencing emissions, radioactive waste), it is vital to save energy . Electronics equipment in offices is often left running continuously and thereby consumes a lot of energy . What does labeling involve? This product meets the requirements for the TCOâ99 scheme which provides for international and environ- mental labeling of personal computers. The labeling scheme was developed as a joint effort by the TCO (The Swedish Confederation of Professional Employees), Svenska Naturskyddsforeningen (The Swedish Society for Nature Conservation) and Statens Energimyndighet (The Swedish National Energy Administration). Approval requirements cover a wide range of issues: environment, ergonomics, usability , emission of electric and magnetic fields, energy consumption and electrical and fire safety . The environmental demands impose restrictions on the presence and use of heavy metals, brominated and chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among other things. The product must be prepared for recycling and the manufacturer is obliged to have an environmental policy which must be adhered to in each country where the company implements its operational policy . The energy requirements include a demand that the computer and/or display , after a certain period of inactivity , shall reduce its power consumption to a lower level in one or more stages. The length of time to reactivate the computer shall be reasonable for the user. Labeled products must meet strict environmental demands, for example, in respect of the reduction of electric and magnetic fields, physical and visual ergonomics and good usability . Below you will find a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from: TCO Development SE-114 94 Stockholm, Sweden Fax: 46 8 782 92 07 Email (Internet): development@tcp.se Current information regarding TCOâ99 approved and labeled products may also be obtained via the Internet, using the address: http://www .tco-info.com/
HP 21" Color Monitor Userâs Guide 22 English Environmental Requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs. Both the flame retardants containing bromine or chloride and the PCBs are suspected of giving rise to severe health effects, including reproductive damage in fish-eating birds and mammals, due to the bio-accumulative* processes. Flame retardants have been found in human blood and researchers fear that disturbances in foetus development may occur. The relevant TCOâ99 demand requires that plastic components weighing more than 25 grams must not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed circuit boards since no substitutes are available. Cadmium** Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer displays. Cadmium damages the nervous system and is toxic in high doses. The relevant TCOâ99 requirement states that batteries, the colour-generating layers of display screens and the electrical or electronics components must not contain any cadmium. Mercury** Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is toxic in high doses. The relevant TCOâ99 requirement states that batteries may not contain any mercury . It also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit. CFCs (freons) The relevant TCOâ99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit boards. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light with e.g. increased risks of skin cancer (malignant melanoma) as a consequence. Lead** Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous system and in higher doses, causes lead poisoning. The relevant TCOâ99 requirement permits the inclusion of lead since no replacement has yet been developed. * Bio-accumulative is defined as substances which accumulate within living organisms ** Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative. Environmental Requirements
Part Number: D2847-90028 Printed in Finland 08.99 ZF5836(A) Paper not bleached with chlorine D2847-90028 *D2847-90028*
Notice The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by Hewlett-Packard. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of Hewlett- Packard Company . ® FD T rinitron is a registered trademark of Sony corporation. Hinweis Inhaltliche Ãnderungen vorbehalten. Hewlett-Packard übernimmt keine Garantie welcher Art auch immer für diese Ausrüstung, einschlieÃlich der (doch nicht begrenzt auf die) Qualitätsgarantie und die Garantie bezüglich Eignung für einen bestimmten Zweck. Hewlett-Packard haftet nicht für in dieser Dokumentation enthaltene Fehler oder für unbeabsichtigte oder indirekte Schäden in Verbindung mit der Lieferung, der Leistung oder der Benutzung der Ausrüstung. Hewlett-Packard übernimmt keine Haftung fur den Betrieb oder die Zuverlässigkeit seiner Software, wenn diese auf Hardware benutzt wird, die nicht von Hewlett-Packard geliefert wurde. Dieses Dokument enthalt proprietäre Informationen, die durch das Copyright geschützt sind. Alle Rechte vorbehalten. Dieses Dokument darf ohne vorherige schriftliche Genehmigung der Hewlett-Packard Company weder ganz noch teilweise fotokopiert, reproduziert oder übersetzt werden. ® FD Triniton ist die registrierte Handelsmarke der Sony Corporation. Avertissement Les informations contenues dans ce document peuvent être modifiées sans préavis. Hewlett-Packard ne donne aucune garantie de quelque sorte que ce soit concernant, sans que ce soit limitatif, les garanties implicites de qualité commerciale de ce matériel, ou la bonne adaptation de celui-ci à un usage particulier. Hewlett-Packard nâest pas responsable des erreurs pouvant apparaître dans ce manuel et nâest pas non plus responsable des dommages directs ou indirects résultant de lâéquipement, des performances et de lâutilisation de ce matériel. Hewlett-Packard ne saurait être tenu pour responsable de lâutilisation et de la fiabilité de son logiciel sur des matériels non fournis par Hewlett-Packard. Les informations contenues dans ce document sont originales et protégées par copyright. T ous droits réservés. L âacheteur sâinterdit en conséquence de les photocopier, de les reproduire ou de les traduire dans toute autre langue, sauf accord préalable et écrit de Hewlett-Packard. ® FD Trinitron est une marque déposée de Sony Corporation. Aviso La información contenida en este documento está sujeta a cambios sin previo aviso. Hewlett-Packard no ofrece ningún tipo de garantÃa con respecto a este material, incluyendo, pero sin limitarse a, las garantÃas implÃcitas de comerciabilidad e idoneidad para un fin determinado. Hewlett-Packard no asume responsabilidad alguna por los posibles errores contenidos o por los daños casuales o emergentes relacionados con el suministro, funcionamiento o uso de este material. Hewlett-Packard no asume responsabilidad alguna por el uso o fiabilidad de su software en equipos que no hayan sido fabricados por Hewlett-Packard. Este documento contiene información patentada, protegida por las leyes del copyright. Reservados todos los derechos. Ninguna parte de este documento puede ser fotocopiada, reproducida o traducida a otro idioma sin la autorización previa y por escrito de Hewlett-Packard Company . ® FD T rinitron es una marca registrado de Sony Corporation. Avviso Le informazioni contenute in questo documento sono soggette a cambiamento senza preavviso. Hewlett-Packard non rilascia garanzie di alcun tipo riguardo a questo materiale, comprese le garanzie implicite di commerciabilità e di idoneità per uno scopo particolare. Hewlett-Packard non sarà ritenuta responsabile per errori contenuti in questo documento, né per danni accidentali o conseguenti alla fornitura, alle prestazioni o allâuso di questo materiale. Hewlett-Packard non si assume alcuna responsabilità riguardo allâuso o allâaffidabilità del proprio software su apparecchiature di altri produttori. Questo documento contiene informazioni di proprietà protette da copyright. Tutti i diritti sono riservati. Nessuna parte di questo documento può essere fotocopiata, riprodotta o tradotta in unâaltra lingua senza un precedente consenso scritto di Hewlett-Packard Company . ® FD Trinitron è un marchio del mestiere di Società per azioni di Sony . Nota As informações contidas neste documento estão sujeitas a alteração sem notificação prévia. A Hewlett-Packard não oferece nenhum tipo de garantia com relação a este material, incluindo, mas não limitada à s, garantias implÃcitas de comercialização e conveniência para um propósito especÃfico. A Hewlett-Packard não será responsável por erros aqui contidos ou por danos incidentais ou conseqüenciais relacionados ao fornecimento, desempenho ou utilização deste material. A Hewlett-Packard não se responsabiliza pelo uso ou confiabilidade se seu software em equipamentos que não sejam fornecidos pela Hewlett-Packard. Este documento contém informações proprietárias protegidas por direitos autorais. T odos os direitos são reservados. Nenhuma parte deste documento pode ser fotocopiada, reproduzida ou traduzida para outro idioma sem o consentimento prévio por escrito da Hewlett-Packard Company . ® FD Trinitron é uma marca comercial da Sony Corporation. Hewlett-Packard France 38053 Grenoble Cedex 9 France © 1999 Hewlett-Packard Company
1 HP D2847A, HP D2847W 21-inch Color Monitors 19.8-inch V iewable Image User â s Guide 0.25 mm dot pitch for excellent graphics FD T rinitron®, anti-glare, anti- static, multilayer screen coating Image adjustment controls to operate on-screen display menus Status indicator Full scan screen that gives an edge to edge image On/Off switch
HP 21" Color Monitor Userâs Guide 2 English Important Safety Instructions Important Safety Instructions Before you plug in your new monitor, read these important safety instructions. For your safety always connect equipment to a grounded wall outlet. Always use a power cord with a properly grounded plug, such as the one provided with the equipment, or one in compliance with your national safety standards. This equipment can be disconnected from the power by removing the power cord from the power outlet. This means the equipment must be located close to an easily accessible power outlet. T o avoid electrical shock, do not open the monitor â s cover . There are no user- serviceable parts inside. Only qualified service personnel should service these parts. Make sure your PC is powered off before connecting or disconnecting a display peripheral. Thank you for selecting HP monitor equipment. T o optimize your comfort and productivity , itâ s important that you set up your work area correctly and use your HP equipment properly . W ith that in mind, we have developed some set-up and use recommendations for you to follow based on estab- lished ergonomic principles. Y ou can consult the online version of W orking in Comfort preloaded on the hard disk of HP computers, or visit HPâ s W orking in Comfort web site at: http://www .hp.com/ergo/ The monitor is quite heavy (the weight is shown in the technical specifications). W e recommend you ask the assistance of a second person when lifting or moving it. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated âdangerous voltageâ within the productâ s enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompa- nying the appliance. W ARNING CAUTION WORKING IN COMFORT
HP 21" Color Monitor Userâs Guide English 3 What Y our New Monitor Of fers Y our HP monitor is a FD T rinitron 21-inch (19.8-inch viewable image), high resolution, multi-synchronous color monitor . Multi-synchronous means that the monitor supports a range of video modes. It is optimized to be used with all Hewlett-Packard computers. Y our HP color monitor has the following features: ⢠A 21-inch FD T rinitron tube, with a 19.8-inch viewable image, and 0.25 mm dot pitch for excellent graphics. Anti-glare, multilayer coating to minimize reflection. ⢠Support of video modes up to 1600 x 1200 at 85 Hz refresh rates, and up to 1800 x 1440 using a 80 Hz refresh rate. ⢠Image adjustment using on-screen display menus. Includes color adjustment and image manipulation controls to optimize the quality and position of the image. ⢠Improved color matching using the sRGB color temperature profile: this can significantly improve color matching with other system devices (printer, computer software, scanner, etc) using sRGB standard color space. ⢠Monitor power management system (VESA 1 standard) controlled from suitably equipped HP computers to automatically reduce the power consumption of the monitor . As an ENERGY ST AR 2 partner , HP has determined that this product meets the ENERGY ST AR guidelines for energy ef ficiency ⢠Monitor Plug and Play capability (VESA DDC1/2Bi standard) that enables the monitor to identify itself to suitably equipped HP computers. ⢠Compliance with ISO 9241-3/-7/-8 ergonomic standards. ⢠Complies with MPRIII, level A guidelines for upper limits of electrical and electrostatic emissions, from the Swedish National Board for Measurement and T esting. ⢠Y our HP monitor complies with TCO99 requirements, refer to the last pages of this manual for more information. 1 VESA is the Video Electronics Standards Association 2 ENERGY ST AR is trademark of United States Environmental Protection Agency (EP A ) What Y our New Monitor Offers
HP 21" Color Monitor Userâs Guide 4 English Setting Up Y our Monitor Where to Place the Monitor Place your monitor on a flat sturdy surface. Ensure the operating site is free from excessive heat, moisture, and sources of electromagnetic fields. Sources of electromagnetic fields include transformers, motors, and other monitors. Connecting the Cables 1 Before you connect any cables, refer to the safety instructions at the beginning of this manual. Make sure your computer and monitor are switched off. 2 Connect the video cable (it has a 15-pin plug) to the video outlet on your com- puter . T ighten the thumbscrews on the plug. 3 Connect the power cord to the monitor . 4 Plug the power cord into the power outlet. Video cable The location of your computer â s video cable connector may be different to the one shown. Refer to the manual that came with your computer , if necessary . Setting Up Y our Monitor Power cords NOTE
HP 21" Color Monitor Userâs Guide English 5 Using Y our Monitor Using Y our Monitor 1 Press the power switch to turn the monitor on or off. 2 When the power is turned on, the power-on indicator will light up. The light indicates the operating state: ⢠Green: The monitor is in normal operation. ⢠Blinking: The monitor is in the active off state. ⢠Off: The monitor is turned off at the power switch or disconnected from the mains outlet. If the power management function of your computer is working properly , you do not need to switch the monitor off or on. This occurs automatically . Pressing the button activates the monitor â s on-screen menu. This menu contains the monitor â s various adjustment features. Select a feature using the and buttons. Scroll to the adjustment feature you require and then press to access the menu. T o adjust the required feature, use the and buttons until the desired changes are complete. Menu language 1 When you press the button for the first time , the Menu language menu appears on the screen. 2 Select a language with the and buttons and press the button to activate your choice.
HP 21" Color Monitor Userâs Guide 6 English 5 Select the adjustment with the and buttons. 6 Press to confirm the selection. The menu disappears and a scale shows the position of the adjustment. In addition to the bar, position of the adjustment is shown as a percentage of the maximum value. The upper number shows the current value and the lower one shows the value where the adjustment started. SIZE & POSITION SHAPE SHARPNESS COLOR MISCELLANEOUS CONTRAST BRIGHTNESS TIL T 4 SIZE & POSITION SHAPE SHARPNESS COLOR MISCELLANEOUS CONTRAST BRIGHTNESS HORIZONT AL CENTERING 1 2 3 Using Y our Monitor Using the menu Menu operations are controlled with the , and buttons. 1 Y ou can display the menu by pressing the button. 2 Select the header with the and buttons. 3 Press to confirm the selection. 4 Adjustment and settings corresponding the header appear below the header field. CONTRAST BRIGHTNESS TIL T OR THOGONALITY TRAPEZOID PINCUSHION PINCUSHION BALANCE EXIT 1280 X 1024 85 Hz 5 6
HP 21" Color Monitor Userâs Guide English 7 TIL T 50 % 77 % 8 7 Using Y our Monitor 7 Adjust with the and buttons. 8 When ready , press the button. Exiting the menu The onscreen menu disappears automatically after 20 seconds of inactivity . Alterna- tively select EXIT and press the button to make the menu disappear immediately . Adjusting the picture of your monitor Y ou should allow the monitor warm up for 20 minutes before making any adjustments to image settings of the monitor . Size and position The illustrations below show the effect of each adjustment when the property is adjusted from the extreme left to the extreme right position. ⢠First correct the property with largest deviation from the correct value then adjust the width and height. 1280 x 1024 85 Hz SIZE & POSITION SHAPE SHARPNESS COLOR MISCELLANEOUS CONTRAST BRIGHTNESS HORIZONT AL CENTERING WIDTH VERTICAL CENTERING HEIGHT PRESET RECALL EXIT Brightness and Contrast With brightness adjustment you may control the brightness of the whole picture. Contrast increases or decreases the brightness difference between light and dark colors. Adjust brightness and contrast adequately according to ambient light conditions to obtain the best picture quality .
HP 21" Color Monitor Userâs Guide 8 English Sharpness SIZE & POSITION SHAPE SHARPNESS COLOR MISCELLANEOUS VERTICAL CONV HORIZONT AL CONV MOIRE COLOR PURITY DEF A UL T SHARPNESS EXIT 1280 x 1024 85 Hz Shape The illustrations below show the effect of each adjustment when the property is adjusted from the extreme left to the extreme right psosition. ⢠When adjusting these properties, set picture width and height so that its edges are visible. Compare the edges of the picture to those of the bezel. ⢠First correct the property with largest deviation from the correct value then adjust the width and height. SIZE & POSITION SHAPE SHARPNESS COLOR MISCELLANEOUS CONTRAST BRIGHTNESS TIL T OR THOGONALITY TRAPEZOID PINCUSHION PINCUSHION BALANCE EXIT 1280 x 1024 85 Hz Preset Recall This function restores the factory defaults and deletes user made settings for: ⢠Size and position ⢠Shape Using Y our Monitor
HP 21" Color Monitor Userâs Guide English 9 V ertical and horizontal convergence A white line on the screen is made up of red, green and blue lines. If there are no convergence errors on the picture, the lines will be exactly overlaid and the resulting color is white. If there is a serious convergence error, separate red, green or blue lines will be seen instead of white. ⢠With Horizontal conv you may minimize the error in vertical lines. ⢠W ith V ertical conv you may minimize the error in horizontal lines. Moire The interference on the screen can be reduced with the help of moire adjustment. Boost the moire adjustment until the interference pattern is acceptable. Moire adjustment slightly reduces picture sharpness. Return the adjustment to zero if there is no risk of moire interference. Using Y our Monitorr Color purity These adjustments can be used to change the color temperature (tint) of the screen. The icon of each adjustment indicates the area on the screen the adjustment affects. COLOR PURITY T OP AND BO TT OM T OP RIGHT BO TTOM RIGHT T OP LEFT BO TTOM LEFT EXIT 1280 x 1024 85 Hz Y ou should allow the monitor to warm up for 20 minutes and demagnetize the monitor before starting the color purity adjustment. Color purity problems do not show up with white test picture. Always use fully red or green test picture. Default sharpness This function restores the factory defaults and deletes user made settings for: ⢠V ertical conv , Horizontal conv , Moire, Color purity NOTE
HP 21" Color Monitor Userâs Guide 10 English 1280 x 1024 85 Hz SIZE & POSITION SHAPE SHARPNESS COLOR MISCELLANEOUS CONTRAST BRIGHTNESS COLOR TEMP 9300 K RED GREEN BLUE SA VE T O CUSTOM 1 EXIT Color With the Color menu the user may adjust the tint of the screen. Color temperature The user can choose between the following fixed color temperatures: ⢠5000K, 6000K, 6500K, 7000K, 8000K, 9300K, 10000K Alternatively , a user specified profile can be selected: ⢠CUSTOM1 User definable color temperature, refer to the chapter âSave to Customâ ⢠sRGB sRGB stands for âstandardized Red, Green and Blueâ colour space. Selecting sRGB means that the monitor displays the images with the same colour balance as other system components (scanner, printer,computer software etc) utilizing the same sRGB color standard. After a preset tint has been selected, the color temperature may be adjusted further as desired. Using Y our Monitor Red, Green, Blue Color monitors mix red, green and blue colors to produce required tint. With Red , Green and Blue intensity control you may finetune any preset tint. ⢠After adjusting Red , Green or Blue the word CUSTOM replaces the color temperature indication.
HP 21" Color Monitor Userâs Guide English 11 Using Y our Monitor Miscellaneous SHAPE SHARPNESS COLOR MISCELLANEOUS CONTRAST BRIGHTNESS DEMA GNETIZE LANGU A GE/SPRACHE/LANGUE ABOUT MONIT OR EXIT 1280 x 1024 85 Hz Save to Custom Y ou may save one custom color temperature setting containing individual Red , Gr een and Blue adjustments. T o create a custom color temperature ⢠Adjust the desired tint with Red , Green and Blue . ⢠Step to Save to Custom and store the settings. T o recall a custom color temperature, refer to the section âColor tempâ. 1280 x 1024 85 Hz SIZE & POSITION SHAPE SHARPNESS COLOR MISCELLANEOUS CONTRAST BRIGHTNESS COLOR TEMP CUST OM RED GREEN BLUE SA VE T O CUSTOM 1 EXIT
HP 21" Color Monitor Userâs Guide 12 English Demagnetize External magnetic fields may cause distortion or discoloration in the picture. Degauss- ing, which takes place automatically when the monitor is switched on, normally maintains faultless color purity . If the purity deteriorates during use, for example when the monitor â s position is changed, perform demagnetizing. During the degaussing process the picture is distorted for a few seconds. When the process is completed, any color impurities will disappear caused by stray magnetic fields. The efficiency of the demagnetization decreases if repeated at intervals shorter than 15 minutes. Menu language The language selection affects the menu languages of your monitor . The following languages are available: * LANGU A GE/SPRACHE/LANGUE ENGLISH DEUTSCH ESP AÃOL FRANÃAIS IT ALIANO POR TUGUÃS EXIT 1280 x 1024 85 Hz The active language is marked with an asterisk. About monitor Shows the display properties of the currently used display mode. 1280 x 1024 85 Hz ABOUT MONIT OR CURRENT MODE RESOLUTION HOR. FREQ. VERT . FREQ. SYNCHRONIZA TION HOR. FREQ. VERT . FREQ. EXIT 1280 x 1024 91,15 KHz 85 KHz 29 - 121 KHz 50 - 180 Hz Using Y our Monitor
HP 21" Color Monitor Userâs Guide English 13 What V ideo Modes are Supported Y our monitor comes with the standard modes shown in the table below . It also supports intermediate video modes. With the intermediate modes, the displayed image may need to be optimized using the buttons on the front panel. All modes are non- interlaced. Y our monitor is GTF* compatible. *GTF stands for General Timing Formula. Re s o lu ti o n Re fre s h ra te /Hz 640 x 400 70 640 x 480 60, 85 800 x 600 85 1024 x 768 75, 85 1280 x 1024 75, 85 1600 x 1200 75, 85, G T F 1800 x 1440 80 Minimizing Eye Strain T o avoid screen flicker and minimize eye strain, use the highest supported image refresh rate for the chosen resolution. It is recommended that you use a refresh rate of 85 Hz. The image refresh rate is the number of times per second that the image is refreshed. Minimizing Energy Consumption If your computer supports VESA monitor power management (available on many HP computers), you can minimize the power consumed by the monitor . There are two power saving modes: ⢠Suspend mode 1 (uses less than 10 W). ⢠Active off mode 2 (uses less than 3 W). In this mode, the monitor â s front panel indicator light blinks slowly in green. T o set these power saving modes, refer to the manual that came with your computer . If your screen is not displaying an image, check the front panel indicator light first â your monitor may be in a power saving mode. Using Y our Monitor 1 Suspend mode is activated when vertical sync is cut by the video controller. 2 Active off mode is activated when both vertical and horizontal sync are cut by the video controller.
HP 21" Color Monitor Userâs Guide 14 English T echnical Specifications T echnical Specifications PI C TU RE TU BE Siz e 21- in ch, v i ewable im age si z e 19.8 in ch D o t p i tch 0.2 5 m m Fa ce p l ate FD T ri n i tron , an ti-g l are, a n tis tati c IN TER F ACE Detach abl e Vi deo C able with 15-pin min i D -SU B Con n ector S C A NNI NG F R E Q UE NC Y H oriz on tal 29 to 121 kH z V er tical 50 to 180 H z M AX. RESO LU TI O N (H x V ) 1800x 1440 ( 80H z) W AR M- U P TIM E 30 m in u tes t o reach optim u m perf orman ce lev el PIXEL C LOCK <300 M H z I MAG E SIZE Stan dard six e: 393 (W) x 293 (H ) mm Maxi m u m siz e: 403 (W)x 302 (H ) mm POW ER MA N AGE MEN T On 160 W ( m ax) Con st an t green LED Stan dby m ode 90W (max ) Con s tan t Gr een LED Su spend mod e 10W (max ) Con st an t green LED Activ e O ff 3W (max ) Gr een blin kin g LED Of f 1W (m ax ) LED is Of f POWER SOU RCE AC 90 to 264 V , 50/60 H z Cu rr en t 2 A OP E RA T IN G EN VI RO N M EN T T emperatu re 0°C to 40°C H u m idi ty 10% RH throu gh 80 % RH ( with ou t con den sation ) STO RAGE EN VI RO N M EN T T emperatu re - 20°C to 60°C H u m i di ty 8 % R H th rou gh 85 % RH (wit h ou t con de n sati on ) C A B IN ET D IME N SION S 51 2 (H ) x 502 (W) x 513 (D ) WEIG H T 30.9 kg TI L T&SW IVEL STA N D T ilt an gle -5° t o 15° Swiv el An gle -90° t o 9 0°
HP 21" Color Monitor Userâs Guide English 15 Care and Cleaning, Environmental Information Care and Cleaning Do not place anything on top of the monitor . Doing so may block the monitor vents and cause damage to the monitor due to overheating. Do not let liquid get on or into the monitor . T o maximize screen life and prevent damage to the picture tube (such as burned phosphor due to leaving the same image on the screen for a long time), it is recom- mended that you: ⢠Use the monitor power management system (on HP computers) or a screen saver program. ⢠A void setting contrast and brightness to their maximum levels for prolonged periods. ⢠If you do not have a power management system or a screen saver program, switch the monitor off or reduce the brightness and contrast to minimum levels when the monitor is not in use. Y our monitor has an anti-glare, anti-static screen coating. T o prevent damage to the monitor screenâ s coating, use a regular household glass cleaner when cleaning the screen. T o clean the screen: 1 Switch the monitor off and remove the power plug (pull the plug, not the cable). 2 W et a soft cotton cloth with the cleaning solution and gently wipe the screen. Do not spray cleaner onto the screen because the cleaner may drip inside the monitor . 3 Dry with a clean, soft cotton cloth. Do not use cleaning solutions containing fluoride, acids, or alkalis. Environmental Information HP has a strong commitment toward the environment. Y our HP monitor has been designed to respect the environment as much as possible. HP can also take back your old monitor for recycling when it reaches the end of its useful life. In fact, HP has a product take-back program in several countries. The collected equipment is sent to one of HPâ s recycling facilities in Europe or the USA. As many parts as possible are reused. The remainder is recycled. Special care is taken for batteries and other potentially toxic substances, which are reduced to non-harmful components through a special chemical process. If you require more details about HPâ s product take-back program, contact your dealer or your nearest HP Sales Office. The cathode ray tube used in this monitor does not contain cadmium.
HP 21" Color Monitor Userâs Guide 16 English Hardware Warranty Hardware W arranty P AR T I - HP General Hardware W arranty General This HP Monitor Hardware W arranty Statement gives you, the customer, express warranty rights from HP , the manufacturer. FOR CONSUMER TRANSACTIONS IN AUSTRALIA AND NEW ZEALAND: THE W ARRANTY TERMS CONT AINED IN THIS ST A TEMENT , EXCEPT T O THE EXTENT LA WFULL Y PERMITTED, DO NOT EXCLUDE, RESTRICT OR MODIFY AND ARE IN ADDITION TO THE MANDA TOR Y ST A TUTOR Y RIGHTS APPLICABLE TO THE SALE OF THIS PRODUCT TO YOU. THE LA WS OF YOUR COUNTR Y MA Y PROVIDE FOR DIFFERENT W ARRANTY RIGHTS. IF SO, YOUR AUTHORIZED HP DEALER OR HP SALES AND SER VICE OFFICE CAN PROVIDE YOU WITH DET AILS. W arranty repair or replacement Hewlett-Packard (HP) warrants this monitor hardware product, or accessory against defects in materials and workmanship for the applicable warranty period stated above, commencing from the date of delivery of the product to the end-user customer. HP does not warrant that the HP hardware will operate uninterrupted or error free. If, during the product warranty period, HP is unable, within a reasonable time, to repair or replace your product to the condition as warranted, you will be entitled to a refund (in the amount of the product purchase price) upon prompt return of the product to your authorized HP dealer or other HP designate. Unless otherwise stated or agreed upon in writing with HP , all hardware components must be returned for refund with the entire system process unit. HP software is covered by the HP Software Product Limited W arranty located in your HP product manual. Unless otherwise stated, and to the extent permitted by local law , hardware products may contain remanufactured parts (equivalent to new in performance) or parts which may have been subject to prior incidental use. HP may repair or replace hardware products (i) with products which are equivalent in performance to the products being repaired or replaced but which may have been subject to prior use, or (ii) with products which may contain remanufactured parts equivalent to new in performance or parts which may have been subject to prior incidental use. M odel W ar r ant y Per iod Serv i ce pr ovi ded D2 847A D2 847W 3 y earsâu n less or igi n al en d-u ser cu stom er h as oth erw ise agreed t o a shorte r pe ri od of warra n ty a t th e time of pu rch ase. On-si te s e rvi ce fo r fi rs t y e ar , a n d re tu rn to a n HP or re pa i r-a u th o ri z e d re se l ler s er v i c e- ce nter fo r the fo llo wi ng two ye a r s .
HP 21" Color Monitor Userâs Guide English 17 Hardware Warranty Proof of Purchase and Warranty Period In order to receive service or support for your hardware product for the warranty period, proof of the original purchase date of the product may be required in order to establish the delivery date of your product. If the delivery date is not available, either the purchase date or the manufacturerâs date (located on the product) becomes the beginning of the warranty period. Limitation of Warranty W arranty does not apply to defects resulting from: (a) improper or inadequate maintenance or calibration; (b) software, interfacing, parts or supplies not supplied by HP; (c) unauthorized repair, maintenance, modifica- tion or misuse; (d) operation outside of the published operating specifications for the product; (e) improper site preparation or maintenance; or (f) such other exclusions as may be expressly set forth in this W arranty Statement. HP MAKES NO OTHER EXPRESS W ARRANTY , WHETHER WRITTEN OR ORAL, WITH RESPECT TO THIS PRODUCT . TO THE EXTENT ALLOWED BY APPLICABLE LOCAL LA W , ANY IMPLIED W ARRANTY OF MERCHANT ABILITY OR FITNESS FOR A P AR TICULAR PURPOSE IS LIMITED T O THE DURA TION OF THE EXPRESS W ARRANTY SET FOR TH ABOVE. Limitation of Liability and Remedies TO THE EXTENT ALLOWED BY APPLICABLE LOCAL LA W , THE REMEDIES IN THIS W ARRANTY ST A TEMENT ARE YOUR SOLE AND EXCLUSIVE REMEDIES. IN NO EVENT SHALL HP BE LIABLE FOR LOSS OF DA T A OR FOR DIRECT , INDIRECT , SPECIAL, INCIDENT AL, OR CONSEQUENTIAL DAMAGE, WHETHER BASED ON W ARRANTY CONTRACT , TOR T , OR ANY OTHER LEGAL THEOR Y . The foregoing limitation of liability shall not apply in the event that any HP product sold hereunder is determined by a court of competent jurisdiction to be defective and to have directly caused bodily injury , death, or property damage. T o the extent allowed by applicable local law , HPâ s liability for property damage does not exceed the greater of $50,000 or the purchase price of the specific product that caused such damage. P AR T II - Y ear 2000 W arranty Subject to all of the terms and limitations of the HP Limited W arranty Statement provided with this HP Product, HP warrants that this HP Product will be able to accurately process date data (including, but not limited to, calculating, comparing, and sequencing) from, into, and between the twentieth and twenty-first centuries, and the years 1999 and 2000, including leap year calculations, when used in accordance with the Product documentation provided by HP (including any instructions for installing patches or upgrades), provided that all other products (e.g. hardware, software, firmware) used in combination with such HP Product(s) properly exchange date data with it. The duration of the Y ear 2000 warranty extends through January 31, 2001.
HP 21" Color Monitor Userâs Guide 18 English Declaration of Conformity Manufacturerâs Name: HEWLETT-P ACKARD France Manufacturerâs Address: 5 , Avenue Raymond Chanas - EYBENS 38053 GRENOBLE CEDEX 09 -FRANCE declares, that the products: Product Name: 21-inch Color Monitor Model Number: D2847 * (*can be blank or any alpha-numeric charater) conform(s) to the following Product Specifications: SAFETY International: IEC 60950:1991 A1 A2 A3 A4 / GB4943-1995 Europe: EN 60950:1992 A1 A2 A3 A4 EMC CISPR 22:1993 A1 A2 / EN 55022:1994 A1 A2 Class B 1) EN 50082-1:1992 IEC 801-2:1992 / prEN 55024-2:1992 - 4kV CD, 8 kV AD IEC 801-3:1984 - 3V/m IEC 801-4:1988 / prEN 55024-4:1992 - 1 kV Power Lines IEC 555-2:1982 A1:1985 / EN 60555-2:1987 IEC 61000-3-3:1994 / EN 61000-3-3:1995 GB9254-1988 FCC Title 47 CFR, Part 15 class B 2) ICES-003, Issue 2 VCCI-B AS/NZ 3548:1992 Supplementary information: The product herewith complies with the requirements of the following Directives and carries the CE mark accordingly: the EMC Directive 89/336/EEC, the Low Voltage Directive 73/23/EEC both amended by the Directive 93/68/EEC. 1) The product was tested in a typical configuration with Hewlett-Packard Personal Computer systems. 2) This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Jean Marc JULIA Grenoble, August 1999 Quality Manager For Compliance Information ONL Y , contact: USA contact: Hewlett-Packard Company , Corporate Product Regulations Manager , 3000 Hanover Street, Palo Alto, CA 94304. (Phone 1 (415) 857-1501). DECLARA TION OF CONFORMITY according to ISO/IEC Guide 22 and EN 45014 Declaration of Conformity
HP 21" Color Monitor Userâs Guide English 19 Regulatory Information Notice for the USA: FCC Class B Statement Federal Communications Commission Radio Frequency Interference Statement Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one or more of the following measures: ⢠Reorient or relocate the receiving antenna. ⢠Increase the distance between the equipment and the receiver. ⢠Connect the equipment to an outlet on a different circuit to the one the receiver is connected to. ⢠Consult your dealer or an experienced radio/TV technician for help. Hewlett-Packard's FCC Compliance T ests were conducted using HP-supported peripheral devices and HP shielded cables, such as those you receive with your system. Changes or modifications not expressly approved by Hewlett-Packard could void the user's authority to operate the equipment. Notice for Canada This Class âBâ digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la Classe B respecte toutes les exigences du règlement sur le matériel brouilleur du Canada. X-Ray Radiation Notice When operating, this product emits x-rays; however, it is well shielded and meets the safety and health requirements of various countries, such as the Radiation Act of Germany and the Radiation Control for Health and Safety Act of the United States. Radiation emitted by this product is less than 0.1 mR/hr (1uSv/hr) at a distance of 10 centimeters from the surface of the cathode ray tube. The x-ray radiation primarily depends on the characteristics of the cathode ray tube and its associated low voltage and high voltage circuitry . Internal controls have been adjusted to ensure safe operation. Only qualified personnel should perform any internal adjustments as specified in the service manual for this product. Replace the cathode ray tube with an identical CR T only . Safety W arning for USA If the power cord is not supplied with your monitor, select the proper power cord according to your national electric safety codes. ⢠USA: use a UL listed detachable power cord.
HP 21" Color Monitor Userâs Guide 20 English Notice for Japan Regulatory Information Notice for Korea
HP 21" Color Monitor Userâs Guide English 21 Congratulations! Y ou have just purchased a TCOâ99 approved and labelled product! Y our choice has provided you with a product developed for professional use. Y our purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products. Why do we have environmentally labeled computers? In many countries, environmental labeling has become an established method for encouraging the adaptation of goods and services to the environment. The main problem, as far as computers and other electronics equipment are concerned, is that environmentally harmful substances are used both in the products and during their manufacture. Since it is not so far possible to satisfactorily recycle the majority of electronics equipment, most of these potentially damaging substances sooner or later enter nature. There are also other characteristics of a computer, such as energy consumption levels, that are important from the viewpoints of both the work (internal) and natural (external) environments. Since all methods of electricity generation have a negative effect on the environment (e.g. acidic and climate-influencing emissions, radioactive waste), it is vital to save energy . Electronics equipment in offices is often left running continuously and thereby consumes a lot of energy . What does labeling involve? This product meets the requirements for the TCOâ99 scheme which provides for international and environ- mental labeling of personal computers. The labeling scheme was developed as a joint effort by the TCO (The Swedish Confederation of Professional Employees), Svenska Naturskyddsforeningen (The Swedish Society for Nature Conservation) and Statens Energimyndighet (The Swedish National Energy Administration). Approval requirements cover a wide range of issues: environment, ergonomics, usability , emission of electric and magnetic fields, energy consumption and electrical and fire safety . The environmental demands impose restrictions on the presence and use of heavy metals, brominated and chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among other things. The product must be prepared for recycling and the manufacturer is obliged to have an environmental policy which must be adhered to in each country where the company implements its operational policy . The energy requirements include a demand that the computer and/or display , after a certain period of inactivity , shall reduce its power consumption to a lower level in one or more stages. The length of time to reactivate the computer shall be reasonable for the user. Labeled products must meet strict environmental demands, for example, in respect of the reduction of electric and magnetic fields, physical and visual ergonomics and good usability . Below you will find a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from: TCO Development SE-114 94 Stockholm, Sweden Fax: 46 8 782 92 07 Email (Internet): development@tcp.se Current information regarding TCOâ99 approved and labeled products may also be obtained via the Internet, using the address: http://www .tco-info.com/
HP 21" Color Monitor Userâs Guide 22 English Environmental Requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs. Both the flame retardants containing bromine or chloride and the PCBs are suspected of giving rise to severe health effects, including reproductive damage in fish-eating birds and mammals, due to the bio-accumulative* processes. Flame retardants have been found in human blood and researchers fear that disturbances in foetus development may occur. The relevant TCOâ99 demand requires that plastic components weighing more than 25 grams must not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed circuit boards since no substitutes are available. Cadmium** Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer displays. Cadmium damages the nervous system and is toxic in high doses. The relevant TCOâ99 requirement states that batteries, the colour-generating layers of display screens and the electrical or electronics components must not contain any cadmium. Mercury** Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is toxic in high doses. The relevant TCOâ99 requirement states that batteries may not contain any mercury . It also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit. CFCs (freons) The relevant TCOâ99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit boards. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light with e.g. increased risks of skin cancer (malignant melanoma) as a consequence. Lead** Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous system and in higher doses, causes lead poisoning. The relevant TCOâ99 requirement permits the inclusion of lead since no replacement has yet been developed. * Bio-accumulative is defined as substances which accumulate within living organisms ** Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative. Environmental Requirements
Part Number: D2847-90028 Printed in Finland 08.99 ZF5836(A) Paper not bleached with chlorine D2847-90028 *D2847-90028*