HP MINI 2102 Maintenance And Service Manual

HP Mini 2102, HP Mini 210, and Compaq Mini 210 Maintenance and Service Guide
© Copyright 2009, 2010 Hewlett-Packard Development Company, L.P. Intel is a trademark of Intel Corporation in the U.S. and other countries. Microsoft, Windows, and Windows Vista are U.S. registered trademarks of Microsoft Corporation. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such pr oducts and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Second Edition: May 2010 First Edition: December 2009 Document Part Number: 595074-001
Safety warning notice WARNING! To reduce the possibility of heat-related in juries or of overheating the device, do not place the device directly on your la p or obstruct the device air vents. U se the device only on a hard, flat surface. Do not al low another har d surface, such as an a djoining optional pr inter, or a soft surface , such as pillows or rugs or clothing, to block airflo w. Also, do not allow the AC adapter to contact the skin or a soft su rface, such as p illows or rugs or clothing, during operat ion. The device and the AC adapter comply with the user-accessible surface temperature limits defined by the In ternational Standard for Safety of Informatio n Technology Equipment (IEC 60950). iii
iv Safety warning notice
Table of contents 1 Product description .................... ........... .............. ............. ............... ........... ................ .... ... 1 2 External component identification ............... .......... ............. ......... ............ .......... ............ .... 5 Identifying the har dware ..... ............ ............... ............... ............ .............. ............ ............... .. ..... 5 Top comp onents ................... ....................... ............................. ....................... .................. ...... 6 TouchPa d ......... ........... ............. ......... ........... ............. .......... ........... ............. .......... ... 6 Lights ........... ........ ........... ........ ........... ........ .......... ......... .......... ........ ........... ........ ...... 7 Keys .... ........... .............. ........... ........... ............ ............ ........... ............. ............ ......... 8 Front components ...... .......... ......... ........... ........ ........... ........ ........... ........... ........ ........... ...... ....... 8 Right-side co mponents ....... ...................... ................... ........................ .................... ............. ..... 9 Left-side components .. ........ .......... ......... .......... ......... .......... ......... .......... ........ ........... ........ .. ..... 10 Display co mponents ....... ........... ............. ........... ............. ........... ............ ........... ............. ...... ... 11 Bottom components .. ........... ........ .......... ........ .......... .......... ........ .......... ........ .......... ........ ...... ... 12 Wireless antennas ..... ........... .......... ............ ......... ............ ............ .......... ............ .......... ...... ..... 13 3 Illustrated parts catalog ............. ............... ..................... ................... ................ .............. 14 Serial number la bel location ............ ........... ............ ............. ........... ............. .......... ............. ... .. 14 Computer majo r components .. ............. ........... ............ ............. ........... ............. ........... ............. 1 5 Display assemb ly components ................. ................ ................. .............. ................ ................ . 2 1 Mass stora ge devices ... .......... ............. .......... ............. ......... ............. .......... ........... ............ .. ... 23 Miscellaneous part s .......... ......... ........... ........ ......... ........... ........ ........... ......... ........ ........... .. ..... 24 Sequential part nu mber listing .......... .......... .............. .......... .......... ............. ........... ............. ..... .. 25 4 Rem oval and re placemen t proced ures .......... ................ ................. ................ ................. 32 Preliminar y replacemen t requireme nts .......... ........... ............. ........... ............ ............. .......... ....... 32 Tools required .......... ............ .............. .............. ........... ............. ........... .............. ...... 32 Service con sideration s ............ ............ ......... ............ ............. .......... ............ ............ . 32 Plastic parts ......... ............ .......... ............ ............. .......... ............ .......... ..... 32 Cables a nd connec tors ................ .............. ................... .............. .............. 33 Drive handling ............. ............ ........... ............. .............. ............. ........... .. 33 Grounding guidelines .. ........... ......... ............ ......... ........... ............ ......... ............ ....... 34 Electrostatic discharge damage ...... ............ ............ ........... ............ ......... .... 34 Packaging and transporting gu idelines ........................................ 35 v
Workstation gu idelines ............... ....................... ........................ 35 Equipmen t guidelines ............ ........... .............. .............. ............ .. 36 Component r eplacement pro cedures .. ......................................................................... ............. 37 Computer feet ........... ........ ........... ........ .......... ......... .......... ........ ........... .......... ........ . 37 Battery .. .......... ............ .......... .......... ........... ............ ........... .......... ............. .......... .... 38 SIM .... .............. ............ ............ ............. ............ ............. ............. ............ ............ .. 39 Service cover ........... ......... ........... ......... ........... ........... ........ ........... ......... ........... ..... 40 Hard drive ................. ...................... ........................... ....................... .................... 43 WWAN modu le ........... ................. .................... .................. .................... ............... 45 WLAN module ............ ........... .............. ........... .............. .......... ............. ............ ....... 47 Memory module ......... ......... ............ ............ .......... ........... .......... ............ ......... ........ 49 RTC battery ......... ................ ..................... ................ ..................... ................ ......... 51 Keyboard .......... ......... ........... ......... ........... ........... ......... ........... ......... ........... ........ .. 52 Top cover .......... ............ ......... ............ ......... ............ ........... .......... ........... .......... ..... 56 Speakers ...... ......... ......... ............ ......... ........... ......... ........... ......... .......... ........... ...... 59 Display ass embly .................. ..................... ................. ....................... ................. .... 61 System board ... ...................... .................... ........................ .................... ................ 64 Fan/heat sin k assembly ........ ........................... .......................... ...................... ........ 67 Power co nnector cable ......................................... ..................................... .............. 69 5 Setup Utility ................. ................... ........................... .................... ......................... .. ...... 71 Starting Se tup Utility ....... ........... ............... ............. ............... ............ ............... ............ .... ....... 71 Using Setup Utility .......... ......... .......... ........ .......... .......... ....... .......... .......... ........ .......... ..... ....... 71 Changing the la nguage of Setup Utility .......... ............ ............. ............. ............ .......... 71 Navigating and selecting in Setup Utility ............ ........ ........... .............. ........... ............ 72 Displaying system information ...... .............. ......... ........... ............ .............. .......... ............ ......... . 72 Restoring default settings in Setup Utility ..... ......... ..... ............ .......... ............. .......... .......... ......... . 72 Exiting Setup Utility ......................... ........................ .................... ......................... ........... ....... 73 Setup Utility Menus ..... ............. .............. ........... ............. ........... ............. ........... ............. ... ...... 73 Main Menu .. ................ ................. ................... ................. ................... ................. . 73 Security Menu .......... ............ .............. .............. ........... ............. ........... .............. ...... 73 System Configuration Menu ....... ......... ............ ............. ......... ............ ............. ........... 74 Diagnostic s Menu ........................ ................................... ........................................ 74 6 Backup and recovery (Windows only) ....... ............................. .................................... ..... 75 Windows 7 ............. ........... .......... ............ .......... ........... ............ ........... .......... ............. .... ...... 75 Backing up and recovering using R oxio BackOnTra ck .................... ................. ............ 75 Creating a copy of the hard drive .............................................................. 76 Performing a recovery .............. ............ ........ .......... ............ ........... ............ 76 Using the Dis aster Reco very utility ............................................. ................. 77 Do wn lo ad in g a nd ex tr ac ti ng th e D is as te r R ec ov er y u ti li ty ............... 7 7 Restoring you r hard drive image ..................................... ............ 77 Using the Insta nt Restore utility .. ................... .................... .................... ..................... 78 vi
Us i ng t he I n st a nt R e st o re u ti l it y wh e n t h e op e r at in g s ys t em i s f u nc t io n in g ......... 7 8 U si n g t h e I ns t a n t R e st o r e u t i l it y w h e n t h e o p e r a t i n g s y s t e m is n o t f u n ct i o n i n g .... 78 Using Windows Ba ckup and Re store ............. ............................. ............................ ... 78 Using system restore points .... ......... ............ ............ ............ ......... ............ ............ ..... 79 When to cre ate restore points .... ............... ................... ................. ............. 79 Creating a system restore point ........ .................. ................. ............... ........ 79 Restorin g to a previous date a nd time ................. ............................... ......... 79 Backing up and recovering using HP R ecovery Manager .................. ............ ....... ........ 80 Backing up your information .. ........... ............. ........... ............. ............. ....... 80 Creating a set o f recovery discs ...... ..................................................... ...... 81 Perfor ming a reco very ................................. ................................................ ............ 82 Recovering using the recovery discs ......... ........... ............ ......... ............ ....... 82 Re co ve ri ng us in g t he par ti ti o n on th e h ar d d ri ve (s el e ct m o de ls o n ly ) .............. 82 Windows XP .................... ......................... ..................... .................... ........................ ...... ..... 83 Backing up your information ..... ........... ........ ........... ........... ......... ........... ........... ........ 83 Creating a copy of the hard drive .............................................................. 84 Performing a recovery .............. ............ ........ .......... ............ ........... ............ 84 Using the Dis aster Recovery U tility .............. ................. ................ .............. . 85 Do wn lo ad in g a nd ex tr ac ti ng th e D is as te r R ec ov er y u ti li ty ............... 8 5 Restoring you r hard drive image ..................................... ............ 85 Using the Instant Re store util ity ............................ ............................... ........ 86 Using the Instant Restore utility when the operating system is functioning . ........................................ .............................. ........ 86 Using the Instant Restore utility when the operating system is not functioning . ........................................ .............................. ........ 86 7 Co nnector pin assign ments .. ........... .............. ............. ........... .............. ............. .............. . 87 Audio-in (mic rophone) .... ..................... ................... ..................... ................... ..................... ... 87 Audio-ou t (headphone) ................ ................ ................. .................... ................ .................... .. 87 External monitor ............ .......... ............ ......... ............ ............ ......... ............ .......... ........... . .. ..... 88 RJ-45 (ne twork) ... ............... ............ ............... ............. ............ ............... ............ .............. .... ... 89 Universal Serial Bus .... ........... ............ ......... ............ .......... ............ ......... ............ .......... ..... ...... 89 8 Power cord set requi rements . ........... ............. ............. .......... ............ ............. ............. .... 90 Requiremen ts for all coun tries ....................... ...................... ............................ ....................... .. 90 Requiremen ts for specific c ountries and r egions ............................................ ............................. 91 9 Recycling ........... ........... ............. ............. ............. ........... .............. ............ ........... ..... ...... 92 Battery ........ ........ ......... .......... ......... .......... ......... ........ ........... ........ ........... ........ ......... . ........... 92 Display .. ........... ............ ............. ............ ........... .............. .......... ............ ............. ......... ....... ... 92 Index . .......... ............ ........... ........... ............ .......... ........... ............. .......... ........... ......... ........ 98 vii
viii
1 Product description Category Description HP Mini 2102 and HP Mini 210 Compaq Mini 210 Produc t Name HP Mini 2102 √ HP Mini 210 √ Compaq Mini 210 √ Proces sor Intel® Atom™ N455 1.66-GHz processor, 512-KB level 2 cache, 667-MHz front-side bus (FSB) √√ Intel® Atom™ N475 1.83-GHz processor, 512-KB level 2 cache, 667-MHz front-side bus (FSB), 6.5W TD P √√ Chipset Intel NM10 Express √√ Graphic s Intel Graphics Media Accele rator 3150 universal memo ry architecture (UMA) graphic s subsystem with Broadcom Crystal HD Enhanced Video Accelerator hardware decoder card √√ Panels All display assemblies include 1 webcam, 1 microphone, 1 speaker box, and 2 wireless local-area network (WLAN) antenna transceivers/cables; wireless wide-area network (WWAN) is optional √√ Wide aspect 16:9 ratio panels, typical brightness: 200n its √√ 25.7 cm (10.1 -in) (1024 × 600) WSVGA, A ntiGlare (AG) with PMMA √√ 25.7 cm (10.1 -in) (1366 × 786) HD AG wit h PMMA √√ Memory One customer-accessible/upg radable memory module slot √√ PC2-4200, 667-MHz, DDR3 √√ 1
Category Description HP Mini 2102 and HP Mini 210 Compaq Mini 210 Supports the following conf igurations: ● 1-GB total system memory NOTE: Supported on computers with all operating systems ● 2-GB total system memory NOTE: Supported only on computers with Windows 7 Premium, Windows 7 Professional, and Window s 7 Starter with Certificate of Authenticity (COA) Emerging Markets and FreeDOS, and in China, Windows XP only. √√ Hard dr ives Supports the following 9.5-mm (0.37-in) × 6.35-cm (2.50-inch), parallel SATA, 7200-rpm hard drives: ● 320-GB NOTE: Supported only on computers with Windows 7 Starter with Notebook COA Emerging Markets, Windows 7 Premium , Windows 7 Pro fessional, and FreeDOS, and in China, Windows XP Home only. ● 250-GB NOTE: Supported only on computers with Windows 7 and FreeDOS, and in China, Windows XP Home only. ● 160-GB NOTE: Supported on compu ters with Win dows 7, Windows XP, and FreeDOS. √√ Optical drive Supports external USB optical drives only √√ Diskette drive Supports external USB diskette drives only √√ Audio/Visual HD audio √√ Supports BEATS audio driver √√ Integrated 1.5-w speakers (2) √√ Fixed integrated, digital microphone √√ Fixed Integrated VGA webcam, 640 × 480 resol ution, up to 30 frames per second √√ Modem Supports external USB modems only √√ Ethernet Integrated Realtek RTL8703EL 10/100 netwo rk interface card (NIC) √√ 2 Chapter 1 Produc t description
Category Description HP Mini 2102 and HP Mini 210 Compaq Mini 210 Wireless Integrated WLAN by way of: ● Atheros 9285G 802.11b/g/n Half M iniCard ● Broadcom 4313/2070 802.11b/g/n (1x 1) and BT Half MiniCard ● Broadcom BCM94313HMG2L 802.11b/g/n (1x1) Half MiniCard ● Ralink RT3090 802.11b/g/n BC4 Bluetooth PCI-e half MiniCard √√ 2 WWAN antennas built into display assembly 2 WLAN antennas built into display assembly √√ Integrated WWAN by way of HP un2400 Mobile Broadband Module (optional) √√ External media cards Digital Media Slot (consumer models) or Media Card Reader (commercial models) with pus h-push technology support ing: ● Memory Stick (MS) ● MS/Pro ● MultiMediaCard (MMC) ● Secure Digital High Capacity (SDHC) Memory Card (standard and large size) ● xD-Picture √√ Internal media cards Two Mini Card slots: ● Full-size Mini Card s lot ● Half-size Mini Card slot √√ Ports Audio-in/out combo, supporting jack detection √√ RJ-45 (Ethernet, includes link and activity light s) √√ USB (2–3) √√ VGA, supporting up to 1600 x 900 external resolutio n @ 60Hz, hot plug /unplug, and auto detection for correct output to wide-aspect vs. standard aspect video √√ 3-pin AC power √√ Keyboard/ pointing device 93% island-style keybo ard √√ 3
Category Description HP Mini 2102 and HP Mini 210 Compaq Mini 210 HP Clikpad TouchPad with multi-touch/gesture support No numeric pad supported. TouchPad with 2 TouchPad butt ons and 2-way scrolling (taps enabled and some gestur es enabled by default) TouchPad on/off button with L ED indicator √√ Power requirements 40-W UMA AC adapter (non-Smart) with localized cable plug support and stepped plug √√ AC adapter connector on cable √√ 1.0-m (3.28-ft) power cord √√ 3-cell Lithium-ion (Li-ion) battery (3s1P, 2.5 5-Ah, 28-Wh) √√ 6-cell battery (3s2P, 2.55-Ah, 55-Wh) √√ 6-cell high capacity battery (3s2P, 3.0-Ah, 66.6-Wh) √√ Security Supports K ensington sec urity lock √√ Operating system Windows 7 Home Basic √ Windows 7 Hom e Premium √√ Windows 7 Home Starter √√ Windows 7 Professional √ Windows XP Home SP3, ultra low-cost personal computer (ULCPC) edition √√ Support for HP QuickWeb √√ FreeDOS (No su pport for HP QuickWeb) √ Serviceability End-user replaceable parts: AC adapter √√ Battery (system) √√ Hard drive √√ Memory module √√ WLAN module √√ WWAN module √√ 4 Chapter 1 Produc t description
2 External component identification Identifying the hardware Components included with the computer may vary by region and model. The illustrations in this chapter identify the standa rd features on most computer models. To see a list of hardware installed in the computer, fol low these steps: 1. Select Start > My Computer . 2. In the left pane of the System Tasks w indow, select View system information . 3. Select Hardware tab > Device Manager . You can also add hardware or modify comp uter configurations using Device Manager. Identifying the hardware 5
Top components TouchPad Item Component Description (1) TouchPad on/off button Turns the TouchPad on and off. Quickly double-tap the button to turn the TouchPad on and off. (2) TouchPad Moves the pointer and selects or activates item s on the screen. (3) Left TouchPad button* Functions like the left button on an external mouse. (4) Right TouchPad button* Functions like the right button on an external mouse. *This table describes factory settings. To view or change pointing device preferences, select Start > Control Panel > Printers and Other Hard ware > Mouse . 6 Chapter 2 External component identification
Lights Item Component Description (1) TouchPad light ● On: The TouchPad is disabled. ● Off: The TouchPad is enabled. (2) Caps lock light On: Caps lock is on. (3) Mute light On: Speaker sound is off. (4) Wireless light ● White: An integrated wireless device, su ch as a wireless local area network (WLAN) device and/ or a Bluetooth device, is on. NOTE: Wireless devices are enabled at the factory. ● Off: All wireless devices are off . Top components 7
Keys Item Component Description (1) Action keys Execute frequently used sy stem functions. (2) fn key Executes frequently used s ystem functions when pressed in combination with a function key or the esc key. (3) Windows logo key Displays the Windows Start menu. (4) Windows applications key Displays a shortc ut menu for items beneath the pointer. Front components Component Description Speakers (2) Produce sound. 8 Chapter 2 External component identification
Right-side components item Component Descr iption (1) Digital Media Slot Supports the following optional digital card formats: ● Memory Stick (MS) ● MS/Pro ● MultiMediaCard (MMC) ● Secure Digital High Capacity (SDHC) Memory Card (standard and large size) ● xD-Picture (2) Power light ● White: The computer is on. ● Blinking white: The com puter is in the Standby state. ● Off: The computer is off or in Hibernation. (3) Power switch ● When the computer is off, slide the s witch to turn on the computer. ● When the computer is on, briefly slide the switch to initiate Hibernation. ● When the computer is in Standby, briefly sl ide the switch to exit Standby. ● When the computer is in Hibernation, briefly slide the switch to exit Hibernation. If the compu ter has stopped responding and Windows shutdown procedures are ineffective, slide and hol d the power switch for at least 5 seconds to turn off the computer. To learn more about your power settings, select Start > Contro l Panel > Perfor mance and Maintenance > Power Option s . (4) Vent Enables airflow to cool internal components. (5) USB ports (2) Connect optional USB devices. NOTE: The computer fan start s up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation. Right-side components 9
item Component Descri ption (6) RJ-45 (network) jack and cover Connects a network cable. (7) Security cable slot Attaches an optional security cable to the com puter. NOTE: The security cable is d esigned to act as a deterrent, but it may not prevent the computer from being mishandled or stolen. Left-side components item Component Descri ption (1) Power connector Connects an AC adapter. (2) Battery light ● Off: The comp uter is ru nning on battery power. ● Blinking white: The battery has reached a low battery level, a critical battery level, or there is a battery error. When th e battery reaches a critical battery level, the battery light begins blinking rapidly. ● Amber: A battery is charging. ● White: The computer is connected to ex ternal power and the battery is fully charged. (3) External monitor port Connects an optional external display, such as a mo nitor or projector, to the computer. (4) Vent Enables airflow to cool in ternal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheat ing. It is normal for the internal fan to cycle on and off during routine operation. (5) Drive light ● Blinking: The hard drive is being access ed. ● Amber (select models only): HP ProtectSmart Hard Drive Protection has temporarily parked the hard drive. 10 Chapter 2 External component identification
item Component Descr iption (6) USB port Connects an optional USB device. (7) Audio-out (headphone) jack/Audio-in (microphone) jack Produces sound when connected to optional powered stereo speakers, headphones, earbuds, a headset, or television audio. Also connects an optional headset microphone. NOTE: When an audio component is connected to the jack, the computer speakers are disabled. The audio component cable must have a 4-condu ctor connector. Display components item Component Descr iption (1) Internal display switch Initiates Standby if the display is c losed while the power is on. NOTE: The display switch is not visible from the out side of the computer. (2) Webcam light On: The webcam is in use. (3) Webcam Records video and c aptures still photographs. NOTE: To capture videos, you need to ins tall additional webcam software. (4) Internal micropho ne Records sound. Display components 11
Bottom components item Component Descri ption (1) Battery release latches (2) Release the battery from the battery bay. (2) Battery bay Holds the battery. 12 Chapter 2 External component identification
Wireless antennas item Component Descr iption (1) WWAN antennas (2)* (sel ect models only) Send and receive wireless signals to communicate with wireless wide-area networks (WWANs), (2) WLAN antennas (2)* Send and receive wireless signals to commu nicate with wireless local-area networks (WLANs). *The antennas are not visible from the outside of the comput er. For optimal transmission , keep the areas immediately around the antennas free from obstructions. To see wireless regulatory notice s, refer to the section of the Regulatory, Safety and Environmental Notices that applies to your country or re gion. To access these n otices, select Start > Help and Support > Us er Guides . Wireless antennas 13
3 Illustrated parts catalog Serial number label location When ordering parts or requesting information, the serial number la bel, located inside the battery bay area of the computer, provides important informat ion that you may need when contacting technical support. NOTE: Serial number label location, format, and color vary on sel ect models. (1) Product name (4) Warranty period (2) Serial number (5) Model description (select models) (3) Product number 14 Chapter 3 Illustra ted parts ca talog
Computer major components Item Desc ription Spare part number (1) Display assembly, 25.7 cm (10.1-in) (includes display panel cabl e, 2 WLAN transceivers and cables, 2 WWAN transceivers and cables, and webcam/microph one module and cable): For use only with HP 2102 and Mini 210 computer models: ● WSVGA, flush glass display assem bly in black 612200-001 ● WSVGA, flush glass display assembly in blue 612198-001 Computer major components 15
Item Desc ription Spare part number ● WSVGA, flush glass display assem bly in red 612202-001 ● WSVGA, flush g lass display assem bly in silver 612196-001 ● HD, flush glass display assembly in black 612201-001 ● HD, flush glass display ass embly in blue 612199-001 ● HD, flush glass display assembly in red 612203-001 ● HD, flush glass display assembly in silver 612197-001 ● WSVGA, AntiGlare, flush glas s display assembly in pink 605040-001 ● HD, AntiGlare, flush glass display assem bly in pink 605041-001 ● WSVGA, AntiGlare, standard display assembly in white 605039-001 For use only with Compaq Mini 210 computer models: ● WSVGA, AntiGlare, standard display assembly in black 589649-001 (2) Keyboard (includes cable) Black: ● For use in Belgium 590527-A41 ● For use in Brazil 590527-201 ● For use in the Czech Republic 590527-221 ● For use in Denmark, Finland, and Norway 590527-DH1 ● For use in France 590527-051 ● For use in French Canada 590527-121 ● For use in Germany 590527-041 ● For use in Greece 590527-DJ1 ● For use in Hungary 590527-211 ● For use in Israel 590527-BB1 ● For use in Italy 590527-061 ● For use in Japan 590527-291 ● For use in Latin America 590527-161 ● For use in the Netherlands 590527-B31 ● For use in Portugal 590527-131 ● For use in Russia 590527-251 ● For use in Saudi Arabia 590527-171 ● For use in Slovenia 590527-BA1 ● For use in South Korea 590527-AD1 16 Chapter 3 Illustra ted parts ca talog
Item Desc ription Spare part number ● For use in Spain 590527-071 ● For use in Switzerland 590527-BG1 ● For use in Taiwan 590527-AB1 ● For use in Thailand 590527-281 ● For use in Turkey 590527-141 ● For use in the United Kingdom 590527-031 ● For use in the United States 590527-001 White (for full-feature models only): ● For use in Belgium 607977-A41 ● For use in Brazil 607977-201 ● For use in the Czech Republic 607977-221 ● For use in Denmark, Finland, and Norway 607977-DH1 ● For use in France 607977-051 ● For use in French Canada 607977-121 ● For use in Germany 607977-041 ● For use in Greece 607977-DJ1 ● For use in Hungary 607977-211 ● For use in Israel 607977-BB1 ● For use in Italy 607977-061 ● For use in Japan 607977-291 ● For use in Latin America 607977-161 ● For use in the Netherlands 607977-B31 ● For use in Portugal 607977-131 ● For use in Russia 607977-251 ● For use in Saudi Arabia 607977-171 ● For use in Slovenia 607977-BA1 ● For use in South Korea 607977-AD1 ● For use in Spain 607977-071 ● For use in Switzerland 607977-BG1 ● For use in Taiwan 607977-AB1 ● For use in Thailand 607977-281 ● For use in Turkey 607977-141 Computer major components 17
Item Desc ription Spare part number ● For use in the United Kingdom 607977-031 ● For use in the United States 607977-001 Pink (for full-feature models only): ● For use in Belgium 607978-A41 ● For use in Brazil 607978-201 ● For use in the Czech Republic 607978-221 ● For use in Denmark, Finland, and Norway 607978-DH1 ● For use in France 607978-051 ● For use in French Canada 607978-121 ● For use in Germany 607978-041 ● For use in Greece 607978-DJ1 ● For use in Hungary 607978-211 ● For use in Israel 607978-BB1 ● For use in Italy 607978-061 ● For use in Japan 607978-291 ● For use in Latin America 607978-161 ● For use in the Netherlands 607978-B31 ● For use in Portugal 607978-131 ● For use in Russia 607978-251 ● For use in Saudi Arabia 607978-171 ● For use in Slovenia 607978-BA1 ● For use in South Korea 607978-AD1 ● For use in Spain 607978-071 ● For use in Switzerland 607978-BG1 ● For use in Taiwan 607978-AB1 ● For use in Thailand 607978-281 ● For use in Turkey 607978-141 ● For use in the United Kingdom 607978-031 ● For use in the United States 607978-001 (3) Top cover (includes TouchPad board and bracket) For full-feature (FF) models only: In black 589676-001 18 Chapter 3 Illustra ted parts ca talog
Item Desc ription Spare part number In pink 608304-001 In white 60830 5-001 For de-feature (DF) models only: In black 596144-001 (4) Speakers (includes cable) 596153-001 (5) System board (includes replacement therm al material): Intel® Atom™ N455 1.66-GHz processor, 51 2-KB level 2 cache, 667-MHz front-side bus (FSB) 608951-001 Intel® Atom™ N455 1.66-GHz processor, 51 2-KB level 2 cache, 667-MHz front-side bus (FSB), decoder ring, WWAN 608952-001 Intel® Atom™ N455 1.66-GHz processor, 51 2-KB level 2 cache, 667-MHz front-side bus (FSB), Broadcom FLEA 608953-001 Intel® Atom™ N455 1.66-GHz processor, 51 2-KB level 2 cache, 667-MHz front-side bus (FSB), decoder ring, Broadcom FLEA, WWAN 608954-001 Intel® Atom™ N475 1.83-GHz processor, 512-KB level 2 cache, 667-MHz FSB, 6.5W TDP 608955-001 Intel® Atom™ N475 1.83-GHz processor, 512-KB level 2 cache, 667-MHz FSB, 6.5W TDP, decoder ring, WWAN 608956-001 Intel® Atom™ N475 1.83-GHz processor, 512-KB level 2 cache, 667-MHz FSB, 6.5W TDP, Broadcom FLEA 608957-001 Intel® Atom™ N475 1.83-GHz processor, 512-KB level 2 cache, 667-MHz FSB, 6.5W TDP, decoder ring, Broadcom FLEA, WWAN 608958-001 (6) Fan/heat sink assembly (includes replacement thermal material) 589681-001 (7) Power connect or cable 589682-001 (8) Base enclosure (inclu des 4 rubber feet an d power connector bracket) For FF models 596145-001 For DF models 589678-001 In pink 608306-001 Rubber Kit (not illustrated, includes 4 rubber feet and RJ-45 cover) 589680-001 (9) Memory module (667-MHz, DDR3): 1-GB 615862-001 2-GB 615863-001 1-GB, WWAN 615864-001 2-GB, WWAN 615865-001 (10) RTC battery 599516-001 (11) WLAN module Computer major components 19
Item Desc ription Spare part number Atheros 9285G 802.11b/g/n Half MiniCard 605560-001 Broadcom 4313/2070 802.11b/g/n (1x 1) and BT Half MiniCard 600370-001 Broadcom BCM94313HMG2L 802.11b/g/n (1x1) Half MiniCard 593836-001 Ralink RT3090 802.11b/g/n BC4 Bl uetooth PCI-e Half MiniCard 602992-001 (12) HP un2400 Mobile Broadband WWAN module 531993-001 (13) Hard drive (includes cable adapter, 4 rubber isol ators, and hard drive bracket) Hard drive: ● 320-GB, 7200-rpm 590819-001 ● 250-GB, 7200-rpm, with WW AN 599665-001 ● 160-GB, 7200-rpm, with WW AN 599666-001 Hard Drive Hardware Kit (not illustrated, includes cable adapter, 4 rubber isolators, and hard drive bracket) 589673-001 (14) Battery 6-cell high-capacity, 66.6-WHr (includes 2 release latches and 2 rubber feet) 596240-001 6-cell, 55-WHr (includes 2 release latches and 2 rubber feet) 596239-001 3-cell, 28-WHr (includes 2 release latches) 590543-001 (15) ● Service cover 589679-001 ● In blue 596146-001 ● In red 596147-001 ● In silver 596148-001 ● In silver (Brazil only) 614994-001 ● In pink 608307-001 ● In white 608308-001 ● For DF models only 600707-001 ● For DF models (Brazil only) 614991-001 20 Chapter 3 Illustra ted parts ca talog
Display assembly components NOTE: Display assembly subcomponents are available only for standard display assemblies. Flush glass display assemblies are availa ble only as hinge-up assemblies. Item Description Spare part number (1) Display bezel (includes WLAN antenna transceivers and cabl es and WWAN antenna trans ceivers and cables): For use only with HP Mini 2102 and 210 computer models 589656-001 For use only with Compaq Mini 210 computer models 589655-001 (2) Display panel: 25.7-cm (10.1-in), WSVGA, AntiGlare display panel (For use only with HP Mini 2102 and 210 computer models) 605039-001 25.7-cm (10.1-in), WSVGA, AntiGlare display panel (For use only with Compaq Mini 210 computer mo dels) 589649-001 (3) Display Hin ge Kit (includes left and right display hinges) 589657-001 Display assembly components 21
Item Description Spare part number Display hinge caps (not illustrated) 598850-001 (4) Webca m/microphone module 589654-001 (5) ● Display panel cable , WSVGA (includes webcam/m icrophone module cable) 589664-001 ● Display panel cable , HD (includes webcam/m icrophone module cable) 599473-001 (6) Display en closure (includes WLAN antenna trans ceivers and cables and WWAN antenna transceivers and cables): For use only with HP computer models in black 589661-001 For use only with HP comput er models in blue 589660-001 For use only with HP computer models in red 589659-001 For use only with HP computer models in silver 589658-001 For use only with HP computer models in pink 60830 0-001 For use only with HP compu ter models in white 608299-001 For use only with Compaq computer models 589662-001 Display Scre w Kit (not illustrated) 589663-001 Display Rubber Kit (not illustrated) 598849-001 22 Chapter 3 Illustra ted parts ca talog
Mass storage devices NOTE: Each hard drive spare part kit includes a cable adapter, bracket, and 4 isolators. Item Descrip tion Spare part number (1) Hard drive: 320-GB, 7200-RPM 590819-001 250-GB, 7200-RPM, with W WAN 599665-001 160-GB, 7200-RPM, with W WAN 599666-001 Hard Drive Ha rdware Kit (not illustrated) 589673-001 (3) External op tical drive: DVD±RW and CD-RW SuperMulti Doubl e-Layer Combo Drive with LightScribe 584383-001 Mass storage devic es 23
Miscellaneous parts Description Spare part number 40-W UMA AC adapter , non-smart RC/V 584540-001 40-W UMA AC adapter , non-smart RC/V 2W 613162-001 Power co rd: For use in Argentina 490371-D01 For use in Austalia 490371-011 For use in Brazil 490371-201 For use in Denmark 490371-081 For use in Europe 490371-021 For use in Israel 490371-BB1 For use in Italy 490371-061 For use in Japan 490371-291 For use in the People's Repu blic of China 490371-AA1 For use in Singapore and the United Kingdom 490371-031 For use in South Africa 490371-AR1 For use in South Korea 490371-AD1 For use in Switzerland 490371-111 For use in Taiwan 490371-AB1 HD video decoder 578237-001 Screw Kit 606695-001 24 Chapter 3 Illustra ted parts ca talog
Sequential part number listing Spare part number Description 490371-001 Power cord for use in North America 490371-011 Power cord for use in Australia 490371-021 Power cord for use in Europe, the Middle East, and Africa 490371-031 Power cord for use in Singapore and the United Kingdom 490371-061 Power cord for use in Italy 490371-081 Power cord for use in Denm ark 490371-111 Power cord for use in Switzerland 490371-201 Power cord for use in Brazil 490371-291 Power cord for use in Japan 490371-AA1 Power cord for use in the People's Republic of China 490371-AB1 Power cord for use in Taiwan 490371-AD1 Power cord for use in South Korea 490371-AR1 Power co rd for use in South Africa 490371-BB1 Power cord for use in Isra el 490371-D01 Power cord for use in Argentia 490371-D61 Power cord for use in India 531993-001 HP u n2400 Mobile Broadband WWAN module 575920-001 Bro adcom 4312G 802.11b/g WiFi and 2070 Bluetooth 2.1 EDR Combo Adapter 578237-001 video decoder, HD 584383-001 DVD±RW and CD-RW SuperMulti Dou ble-Layer Combo Drive with Ligh tS cribe (external op tical drive) 584540-001 40-W UMA AC adapter, no n-smart RC/V 589649-001 25.7-cm (10.1-in) WSVGA, AntiGlare, standard disp lay assembly for use only with Compaq Mini 210 computer models (includes display panel c able, 2 WLAN transceivers and cables, 2 WWAN transceivers and cables, and webc am/microphone module and cable) 589654-001 Webcam/microphone module 589655-001 Display bezel for use only with Compaq Mi ni 210 computer m odels (includes WLA N antenna transceivers and cables and WWAN antenna transceivers and cables) 589656-001 Display bezel for use only with HP Mini 2102 and 210 computer models (includes WLAN ant enna transceivers and cables and WWAN antenna transceivers and cables) 589657-001 Display Hinge Kit (includes left and rig ht display hinges) 589658-001 Display enclosure for us e only with HP Mini 2102 and 210 compu ter models in silver (in cludes WLAN antenna transceivers and cables an d WWAN antenna tran sceivers and cables) Sequential part number listing 25
Spare part number Description 589659-001 Display enclosure for use onl y with HP Mini 2102 and 2 10 computer models in red (includes WLAN antenna transceivers and cables and WWAN antenna tr ansceivers and cables) 589660-001 Display enclosure for use onl y with HP Mini 2102 and 210 com puter models in blue (includes WLAN antenna transceivers and cables an d WWAN antenna transc eivers and cables) 589661-001 Display enclosure for use onl y with HP Mini 210 2 and 210 computer m odels in black (includes WLAN antenna transceivers and cables an d WWAN antenna transc eivers and cables) 589662-001 Displ ay enclosure for use only with Compaq Mini 210 computer models (includes WLAN an tenna transceivers and cables and WWAN antenna transcei vers and cables) 589663-001 Display Screw Kit 589664-001 Display panel cable (include s webcam /microphone module cable) 589673-001 Hard Drive Hardware Kit ( not illustrated, in cludes cable adapter, 4 rubber isolators, and hard drive bracket) 589676-001 Top cover, black for use only with FF comp u ter models (includes TouchPad board and bracket) 589678-001 Base enclosure, for use only with DF comput er models (includes 4 rubber feet and power connector bracket) 589679-001 Service cover 589680-001 Rubber Kit (includes 4 rubber feet and RJ-45 cover) 589681-001 Fan/heat sink assembly (inc ludes replacement thermal m aterial) 589682-001 Power connector cable 590527-001 Keyboard, black, for use only in the United States (includes cable) 590527-031 Keyboard, black, for use only in the United Kingdom (includes cable) 590527-041 Keyboard, black, for use only in Germ any (includes cable) 590527-051 Keyboard, black, for use only in France (in cludes cable) 590527-061 Keyboard, black, for use only in Italy (includes cable) 590527-071 Keyboard, black, for use only in Spain (inclu des cable) 590527-121 Keyboard, black, for use only in French Can ada (includes cable) 590527-131 Keyboard, black, for use only in Portu gal (includes cable) 590527-141 Keyboard, black, for use only in Turkey (includes cabl e) 590527-161 Keyboard, black, for use only in Latin Am erica (includes cable) 590527-171 Keyboard, black, for use only in Saudi Arabia (includes cable) 590527-201 Keyboard, black, for use only in Brazil (includes cable) 590527-211 Keyboard, black, for use only in Hungary (includes cable) 590527-221 Keyboard, black, for use only in the Czech Republic (includes cable) 590527-251 Keyboard, black, for use only in Ru ssia (includes cable) 590527-281 Keyboard, black, for use only in Thailand (in cludes cable) 26 Chapter 3 Illustra ted parts ca talog
Spare part number Description 590527-291 Keyboard, black, for use only in Japan (includes cable) 590527-A41 Keyboard, black, for use only in Belgium (includes cable) 590527-AB1 Keyboard, black, for use only in Taiwan (includes cable) 590527-AD1 Keyboard, black, for use only in South Korea (includ es cable) 590527-B31 Keyboard, black, for use only in the Netherlands (includes cable) 590527-BA1 Keyboard, black, for use only in Slovenia (includes cable) 590527-BB1 Keyboard, black, for use only in Israel (includes cable) 590527-BG1 Keyboard, black, for use on ly in Switzerland (includes cable) 590527-DH1 Keyboard, black, for use only in Denmark, Finland, and Norway (includes cable) 590527-DJ1 Keyboard, pink, for use only in Greece (inclu des cable) 590543-001 3-cell, 28-WHr battery (includes 2 release latches ) 590819-001 320 -GB, 7200-rpm hard driv e (includes cable adapter, 4 ru bber is olators, and hard drive bracket) 593836-001 Broadcom BCM94313HMG2L 80 2.11b/g/n (1x1) Half MiniCard 596144-001 Top cover, black, for use only with DF co mputer models (includes TouchPad board and bracket) 596145-001 Base enclosure, for use o nly with FF computer models (includes 4 rubber feet and power connecto r bracket) 596146-001 Service cover, blue 597147-001 Service cover, red 596148-001 Service cover, silver 596153-001 Speakers (includes cable) 596239-001 6-cell, 55-WHr battery (includes 2 release latches and 2 rubber feet) 596240-001 6-cel l high-capacity, 66.6-WHr battery (incl udes 2 release latches and 2 rubber feet) 598849-001 Display Rubber Kit (not illustrated) 598850-001 Display hinge caps (not illustrated) 599473-001 Display panel cable, HD (includes webcam/microph one module cable) 599516-001 RTC battery 599665-001 250 -GB, 7200-rpm hard driv e (includes cable adapter, 4 ru bber is olators, and hard drive bracket) 599666-001 160 -GB, 7200-rpm hard driv e (includes cable adapter, 4 ru bber is olators, and hard drive bracket) 600707-001 Service cover, for use o nly with DF computer models 602992-001 Ralink RT3090 802.11b/g/ n BC4 Bluetooth PCI-e half MiniCard 605039-001 25.7-cm (10.1-in) WSVGA, AntiGlare, standard display assembly for us e only with HP Mini 2102 and 210 computer models (includes display panel cable, 2 WLAN transceivers and cables, 2 WWAN transceivers and cables, and webcam/micro phone module and cable) Sequential part number listing 27
Spare part number Description 605040-001 25.7-cm (10.1-in) WS VGA, AntiGlare, flush glass di splay assembly in pink (includes display panel cable, 2 WLAN transceivers and cables, 2 WWAN transceivers an d cables, and webcam/ microphone module and cable) 605041-001 25.7-cm (10.1-in) HD, AntiGl are, flush glass display assembly in pink (includes display panel cable, 2 WLAN transceivers and cables, 2 WWAN transceivers an d cables, and webcam/ microphone module and cable) 605560-001 Atheros 9285G 802.11b/g/n Half M iniCard 606695-001 Screw Kit 607978-001 Keyboard, pink, for use only in the United Stat es (includes cable) 607978-031 Keyboard, pink, for use only in the United King dom (includes cable) 607978-041 Keyboard, pink, for use only in Germany (includes cabl e) 607978-051 Keyboard, pink, for use only in France (includes cable) 607978-061 Keyboard, pink, for use only in Italy (includes cable) 607978-071 Keyboard, pink, for use only in Spain (includes cable) 607978-121 Keyboard, pink, for us e only in French Canada (includes cable) 607978-131 Keyboard, pink, for us e only in Port ugal (includes cabl e) 607978-141 Keyboard, pink, for use only in Turkey (includes cable) 607978-161 Keyboard, pink, for use only in Latin America (inclu des cable) 607978-171 Keyboard, pink, for use only in Saudi Arabia (includes cable) 607978-201 Keyboard, pink, for use only in Brazil (includes cable) 607978-211 Keyboard, pink, for use only in Hungary (includes cable) 607978-221 Keyboard, pink, for use only in the Czech Republ ic (includes cable) 607978-251 Keyboard, pink, for use only in Russia (inclu des cable) 607978-281 Keyboard, pink, for use only in Thailand (includes cable) 607978-291 Keyboard, pink, for us e only in Japan (includes cable) 607978-A41 Keyboard, pink, for use only in Belgium (includes cable) 607978-AB1 Keyboard, pink, for use only in Taiwan (includes cable) 607978-AD1 Keyboard, pink, for use onl y in South Korea (includes cable) 607978-B31 Keyboard, pink, for use only in the Netherlands (includes cable) 607978-BA1 Keyboard, pink, for use only in Slovenia (includes cable) 607978-BB1 Keyboard, pink, for use only in Israel (includes cable) 607978-BG1 Keyboard, pink, for use only in Switzerland (includes cable) 607978-DH1 Keyboard, pink, for use only in Denm ark, Finland, and No rway (includes cable) 607978-DJ1 Keyboard, pink, for use only in Greece (inclu des cable) 28 Chapter 3 Illustra ted parts ca talog
Spare part number Description 607977-001 Keyboard, white, for use only in the United States (includes cabl e) 607977-031 Keyboard, white, for use only in the United Kingdom (includes cable) 607977-041 Keyboard, white, for use only in Germany (includes cable) 607977-051 Keyboard, white, for use only in France (includes cable) 607977-061 Keyboard, white, for use only in Italy (includes cable) 607977-071 Keyboard, white, for use only in Spain (includes cable) 607977-121 Keyboard, whit e, for use only in French Canada (incl udes cable) 607977-131 Keyboard, white, for use only in Portugal (includes cable) 607977-141 Keyboard, white, for use only in Turkey (includes cable) 607977-161 Keyboard, white, for use only in Latin America (includes cable) 607977-171 Keyboard, white, for use only in Saudi Arabia (incl udes cable) 607977-201 Keyboard, white, for use only in Brazil (includes cable) 607977-211 Keyboard, white, for use only in Hungary (includes cable) 607977-221 Keyboard, white, for use only in the Czech Republic (incl udes cable) 607977-251 Keyboard, white, for use only in Russia (includes cable) 607977-281 Keyboard, white, for use only in Thail and (includes cable) 607977-291 Keyboard, whit e, for use only in Japan (includes cable) 607977-A41 Keyboard, white, for use only in Belgium (includes cable) 607977-AB1 Keyboard, white, for use only in Taiwan (in cludes cable) 607977-AD1 Keyboard, whit e, for use only in South Korea (incl udes cable) 607977-B31 Keyboard, white, for use only in the Netherlands (includes cabl e) 607977-BA1 Keyboard, white, for use only in Slovenia (in cludes cable) 607977-BB1 Keyboard, white, for use only in Israel (in cludes cable) 607977-BG1 Keyboard, white, for use on ly in Switzerland (includes cable) 607977-DH1 Keyboard, white, for use only in Denmark, Finland, and Norway (includes cable) 607977-DJ1 Keyboard, white, for use only in Greece (includes cable) 608299-001 Display enclosure for use onl y with HP Mi ni 2102 and 210 computer models in white (includes WLAN antenna transceivers and cables an d WWAN antenna tran sceivers and cables) 608300-001 Display enclosure for use onl y with HP Mini 2102 and 210 computer models in pink (includes WLAN antenna transceivers and cables an d WWAN antenna tran sceivers and cables) 608304-001 Top cover, pink for use only with FF computer models (includes TouchPad board and bracket) 608305-001 Top cover, white for use o nly with FF co mputer mo dels (includes TouchPad board and bracket) 608306-001 Base enclosure, pink (inclu des 4 rubber feet and power con nector bracket) Sequential part number listing 29
Spare part number Description 608307-001 Service cover, pink 608308-001 Service cover, white 608951-001 Intel® Atom™ N455 1.66-GHz processor, 512 -KB level 2 cache, 667-MHz front-side bus (FSB) 608952-001 Intel® Atom™ N455 1.66-GHz processor, 512 -KB level 2 cache, 667-MHz front-side bus (FSB), decoder ring, WWAN 608953-001 Intel® Atom™ N455 1.66-GHz processor, 512 -KB level 2 cache, 667-MHz front-side bus (FSB), Broadcom FLEA 608954-001 Intel® Atom™ N455 1.66-GHz processor, 512 -KB level 2 cache, 667-MHz front-side bus (FSB), Broadcom FLEA, WWAN 608955-001 Intel® Atom™ N475 1.83-GHz processor, 512-KB level 2 cache, 667-MHz FSB, 6.5W TDP 608956-001 Intel® Atom™ N475 1.83-GHz processor, 512-KB level 2 cache, 667-MHz FSB, 6.5W TDP, decoder ring, WWAN 608957-001 Intel® Atom™ N475 1.83-GHz processor, 512-KB level 2 cache, 667-MHz FSB, 6.5W TDP, Broadcom, FLEA 608958-001 Intel® Atom™ N475 1.83-GHz processor, 512-KB level 2 cache, 667-MHz FSB, 6.5W TDP, decoder ring, Broadcom FLEA, WWAN 612196-001 25.7-cm (10.1-in) WSVGA, flush glass display assembly in silver (includes display panel cable, 2 WLAN transceivers and cables, 2 WWAN tran sceivers and cables, and webcam/microphone module and cable) 612197-001 25.7-cm (10.1-in) HD, flu sh glass display assem bly in silver (includes display panel cable, 2 WLAN transceivers and cables, 2 WWAN tran sceivers and cables, and webcam/microphone module and cable) 612198-001 25.7-cm (10.1-in) WSVGA, flush glass display assembly in blue (includes display panel cable, 2 WLAN transceivers and cables, 2 WWAN tran sceivers and cables, and webcam/microphone module and cable) 612199-001 25.7-cm (10.1-in) HD, flu sh glass display assem bly in blue (includes display panel cable, 2 WLAN transceivers and cables, 2 WWAN transceivers and cables, and webcam/m icrophone module and cable) 612200-001 25.7-cm (10.1-in) WSVGA, flush glass display assembly in black (includes display panel cable, 2 WLAN transceivers and cables, 2 WWAN tran sceivers and cables, and webcam/microphone module and cable) 612201-001 25.7-cm (10.1-in) HD, flu sh glass display assembly in black (includes display panel cable, 2 WLAN transceivers and cables, 2 WWAN tran sceivers and cables, and webcam/microphone module and cable) 612202-001 25.7-cm (10.1-in) WSVGA, flush glass display assemb ly in red (includes display panel cable, 2 WLAN transceivers and cables, 2 WWAN tran sceivers and cables, and webcam/microphone module and cable) 612203-001 25.7-cm (10.1-in) HD, flu sh glass display assembly in red (includes display panel cable, 2 WLAN transceivers and cables, 2 WWAN transceivers and cables, and webcam/m icrophone module and cable) 613162-001 40-W UMA AC adapter, non-smart RC/V 2W 614991-001 Service cover, for use only wi th DF computer models (Brazil only) 30 Chapter 3 Illustra ted parts ca talog
Spare part number Description 614994-001 Service cover, silver (Brazil only) 615862-001 1-GB memory module (667-MHz, DDR 3): 615863-001 2-GB memory module (667-MHz, DDR 3): 615864-001 1-GB memory module (667-MHz, D DR3), WWAN 615865-001 2-GB memory module (667-MHz, D DR3), WWAN Sequential part number listing 31
4 Removal and replacement procedures Preliminary replacement requirements Tools required You will need the following tools to comple te the removal and replacement procedures: ● Flat-bladed screwdriver ● Magnetic screwdriver ● Phillips P0 and P1 screwdrivers Service considerations The following sections include some of th e cons iderations that you must keep in mind during disassembly and assembly procedures. NOTE: As you remove each subassembly from th e device, plac e the subassembly (a nd all accompanying screws) away from th e work area to prevent damage . Plastic parts CAUTION: Using excessive force during disassembly and reassembly c an damage plastic parts. Use care when handling the plastic parts . Apply pressure only at t he points designated in the maintenance instructions. 32 Chapter 4 Removal an d replacement procedures
Cables and connectors CAUTION: When servicing the device, be sure that cables are pla ced in their proper locations during the reassembly process. Impr oper cable placement can damage the device. Cables must b e handled with ex treme care to avoid damage. Apply only the tension required to unseat or seat the cables during removal and insertion. Ha ndle cables by the connector whenever possib le. In all cases, avoid bending, twisting, or tearing cables. Be sure that cables are routed in such a way that they cannot be caught or snagged by parts bein g removed or replaced. Handle flex cables with extreme care; thes e cables tear easi ly. Drive handling CAUTION: Drives are fr agile componen ts that must be handled with care. To prevent damage to the device, damage to a drive, or loss of information, observe these precautions: Before removing or inserting a hard driv e, shut down the device . If you are unsu re whether the dev ice is off or in Hibernation, turn the device on, an d then shut it down through the operating system. Before handling a drive, be sure that you are d ischarged of stat ic electricity. While handling a drive, avoid touching the connector. Handle drives on surfaces covered with at l east one inch of s hock-proof fo am. Avoid dropping drives from any height onto any surface. After removing a hard drive, an optical drive, or a diskette drive, place it in a static-proof bag. Avoid exposing a ha rd drive to products th at have magnetic fields, such as monitors or sp eakers. Avoid exposing a drive to temp erature extremes or liquid s. If a drive must be ma iled, place the drive in a bubble pack mailer or other suitable form of pro tective packaging and label the package “ FRAGILE.” Preliminary replac ement requirements 33
Grounding guidelines Electrostatic discharge damage Electronic componen ts are sensiti ve to electrostati c discharge (ESD). Circuitry design and structure determine the degree of sensitiv ity. Networks built into many integrated circuits provide some protection, bu t in many cases, ESD contains en ough power to al ter device parameters or melt silicon junctions. A discharg e of static electrici ty from a fing er or other conductor can destroy static-sensitive devices or microcircuitry. Even if the spark is neither felt nor hear d, damage may have occ urred. An electronic device exposed to ESD may not be affected at all and can work perfectly throughout a normal cycle. Or the device may fu nction normally for a while, then degrade in the internal layer s, reducing its life expectancy. CAUTION: To prevent damage to the device when yo u are r emoving or installing internal components, observe these precaution s: Keep components in their e lectr ostatic-safe containers until you are ready to install them. Use nonmagnetic tools. Before touching an electr onic compone nt, discha rge static electr icity by using the guidelines described in this section. Avoid touching pins, leads, and ci rcuitry. Han dle electron ic comp onents as little as possible. If you remove a component, place it in an electrostati c-sa fe container. The following table shows how humidi ty affects the electrostatic voltag e levels generated by different activities. CAUTION: A product can be degraded by as little as 700 V. Typical electro static voltage levels Relative humidity Event 1 0% 40% 55% Walking across carpet 35,000 V 15,000 V 7,500 V Walking across vinyl floor 12,000 V 5,000 V 3,000 V Motions of bench worker 6,000 V 800 V 400 V Removing DIPS from plastic tube 2,000 V 700 V 400 V Removing DIPS from vinyl tray 11,500 V 4,000 V 2,000 V Removing DIPS from Styrofoam 14,500 V 5,000 V 3,500 V Removing bubble pack from PCB 26,500 V 20,000 V 7,000 V Packing PCBs in foam-lined box 2 1,000 V 11,000 V 5,000 V 34 Chapter 4 Removal an d replacement procedures
Packaging and transp orting guidelines Follow these grounding guidelines when packagin g and transporting equipment: ● To avoid hand co ntact, transport pr oducts in static-safe tube s, bags, or bo xes. ● Protect ESD-sensitive part s and assemblies with co nductive or approved co ntainers or packaging. ● Keep ESD-sensitive parts in their containers unti l the parts arrive at static-free workstations. ● Place it ems on a gr ounded surface before removing items from their containers. ● Always be pr operly grounded when t ouching a component or assembly. ● Store reusable ESD-sensitive parts from assemblies in protecti ve packaging or nonconductive foam. ● Use transporters a nd conveyors made of antistatic belts a nd roller bushings . Be sure that mechanized eq uipment used for moving materials is wired to ground and that proper materia ls are selected to avoid static charging. When ground ing is not possible, use an ionizer to dissipate electric charges. Workstation guidelines Follow these grounding workstatio n guidelines: ● Cover the workstation with approv ed static-shielding material. ● Use a wrist strap connected to a properly grounded work sur face and use properly grounded tools and equipment. ● Use conductive field service tools, such as cutters, screwdrivers, and vacuums. ● When fixtures must dir ectly contact dissipative surfaces, use fixtures made only of stat ic-safe materials. ● Keep the work area free of nonconductive material s, such as ordinary plastic assem bly aids and Styrofoam. ● Handle ESD-sensitive components, parts, a nd asse mblies by the case or PCM laminate. Handle these items only at static-free workstations. ● Avoid contact with pins, leads, or circuitry. ● Turn off power and input sig nals before inserting or removing conn ectors or test equipment. Preliminary replac ement requirements 35
Equipment guidelines Grounding equipment must include either a wrist st rap or a foot strap at a grounded workstation. ● When seated, wear a wrist strap connected to a gr ounded system. Wrist straps are flexible straps with a minimum of one megohm ±10% resistance in the ground cords. To pro vide proper ground, wear a strap snugly ag ainst the skin at all time s. On grounded mats wi th banana-plug connectors, use alligator clips to connect a wrist strap. ● When standing, use foot straps and a grou nded floor mat. Foot straps (heel, t oe, or boot straps) can be used at stan ding workstations and are com p atible with most types of shoes or boots. On conductive floors or dissipative floor mats, use foot straps on both feet with a minimum of one megohm resistance between the operator and ground . To be effective, the c onductive strips must be worn in contac t with the skin. The following grounding equipment is recommend ed to prevent elect rostatic damage: ● Antistatic tape ● Antistatic smocks, aprons, and sleeve p rotectors ● Conductive bin s and other assembly or soldering aids ● Nonconductive foam ● Conductive tabletop workstations with ground cords o f one megohm resistance ● Static-dissipative tables or floor mats with hard ti es to the ground ● Field service kits ● Static awareness labels ● Material-handling packages ● Nonconductive plastic ba gs, tubes, or boxes ● Metal tote boxes ● Electrostatic voltage levels and protective ma terials The following table lists the shielding protection provided by antistatic bags and floor mats. Mater ial Use Voltag e prote ction level Antistatic plastic Bags 1,500 V Carbon-loaded plastic Floor mats 7,500 V Metallized laminate Floor mats 5,000 V 36 Chapter 4 Removal an d replacement procedures
Component replacement procedures This chapter provides remova l and replacement procedures. There are as many as 33 screws, in 5 di fferent sizes, th at must be rem oved, replace d, or loosene d when servicing the co mputer. Make special note of each screw size and location during removal and replacement. Computer feet The computer feet are adhesive-ba cke d rubber pads. The feet are included in the Ru bber Feet Kit, spare part number 589680-001. There are 4 rubber feet th at attach to the base enclosure in the locations shown in the following illustration. Component re placement procedures 37
Battery Description Spare part number 6-cell high-capacity, 66.6-WHr (includes 2 release latches and 2 rubber feet) 596240-001 6-cell, 55-WHr (includes 2 release latches and 2 rubber feet) 596239-001 3-cell, 28-WHr (includes 2 release latches ) 590543-001 Before disass embling the computer, fo llow these steps: 1. Shut down the computer. If you ar e unsure whether the computer is o ff or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external device s connected to the computer. 3. Disconnect the power from the computer by firs t unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. Remove the battery: 1. Turn the computer upside-down on a flat surface, with the battery bay toward you. 2. Slide the battery lock latch (1) to unlock the battery. 3. Slide the battery release latch (2) to release the battery. 4. Remove the battery (3) . Reverse this procedure to install a battery. 38 Chapter 4 Removal an d replacement procedures
SIM Before removing the SIM, follow these steps: 1. Shut down the computer. If you ar e unsure whether the computer is o ff or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external device s connected to the computer. 3. Disconnect the power from the computer by firs t unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the battery (see Battery on page 38 ). Remove the SIM: 1. Press in on the SIM (1) to release it from the SIM slot. 2. Remove the SIM (2) from the SIM slot. Install the SIM by inserting it into the SIM slot until you hear a click. Component re placement procedures 39
Service cover Description Spare part number Service cover 589679-001 Service cover, blue 596146-001 Service cover, red 596147-001 Service cover, silver 596148-001 Service cover 589679-001 Service cover, for use only with DF computer models 600707-001 Service cover, pink 608307-001 Service cover, white 608308-001 Service cover, for use only with DF computer models (Brazil only) 614991-001 Before removing the servic e cove r, follow these s teps: 1. Shut down the computer. If you ar e unsure whether the computer is o ff or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external device s connected to the computer. 3. Disconnect the power from the computer by firs t unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the battery (see Battery on page 38 ). Remove the service cover: 1. Press the right release butto n (1) . 40 Chapter 4 Removal an d replacement procedures
2. Release the right side of the service cover (2) by lifting it slightly away from the base enclosure. NOTE: It is normal for the service cover to flex sl ightly when it is released. You may al so hear some popping noises as the service cover ta bs disengage from the base enclosure slots. 3. Press the left release button (1) . 4. Release the left side of the service cover (2) by lifting it slightly from away from the base enclosure. Component re placement procedures 41
5. Continue lifting the rear edge of the servic e cover (1) up and forward until it rests at a n angle, and then remove the service cover (2) . Install the service cover: 1. Place the service cover above the comput er at an an gle, with the fr ont edge toward the front of the computer. 2. Insert the front edge of the service cover (1) into the front edge of the base enc losure, making sure the tabs on the cover insert into the slots on the base enclosure (2) . 42 Chapter 4 Removal an d replacement procedures
3. Swing the rear edge of the service cover (1) back and down, and then firmly press down on the cover (2) so the clips on the cover a ccess the slots on the base enclosur e. Hard drive NOTE: Each hard drive spare part kit includes a cabl e ada pter, bracket, and four rubber isolators. Description Spare part number Hard drive: 320-GB, 7200-RPM 590819-001 250-GB, 7200-RPM, WWAN 599665-001 160-GB, 7200-RPM, WWAN 599666-001 Hard Drive Hardware Kit 5896 73-001 Before removing a hard drive, follow these steps: 1. Shut down the computer. If you ar e unsure whether the computer is o ff or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external device s connected to the computer. 3. Disconnect the power from the computer by firs t unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the battery (see Battery on page 38 ). 5. Remove the service cover (see Battery on page 38 ). Remove the hard drive: 1. Disconnect the hard drive cable (1) fr om the system board . 2. Use the Mylar tab (2) on the right side of the hard drive to lift the right side of the drive (3) until it rests at an angle. Component re placement procedures 43
3. Remove the hard drive (4) by sliding it up and to the right at an angle. 4. If it is necessary to replace the ha rd drive bracket, follow these steps: a. Disconnect the cable adapter (1) from the hard drive. b. Remove the f our Philli ps PM3. 0×3.0 sc rews (2 ) that secure the hard drive bracket to the drive. c. Remove the hard drive bracket (3) . d. Remove the four rubber isolators (4) from the bracket. Reverse this procedure to r easse mble and install the hard drive. 44 Chapter 4 Removal an d replacement procedures
WWAN module Description Spare part number HP un2400 Mobile Broadband WWAN module 531993-001 CAUTION: The WWAN module and the W LAN module ar e not interchangeable. To prevent an unresponsive system, replace the wireless mo dule only with a wireless module authorized for use in the computer by the govern mental agency that regulates wireless de vices in your country or region. If you replac e the module and then rece ive a warning message, remove the module to restore device functionality, and th en contact technical support. Before removing the WWAN modu le, follow these steps: 1. Shut down the computer. If you ar e unsure whether the computer is o ff or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external device s connected to the computer. 3. Disconnect the power from the computer by firs t unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the battery (see Battery on page 38 ). 5. Remove the service cover (see Service cover on page 40 ). Remove the WWAN module: 1. Disconnect the WWA N antenna cables (1) from the terminals on the WWAN module. NOTE: The red WWAN antenna cable is connected to the WWAN module “Main” terminal. The blue WWAN antenna ca ble is connecte d to the WWAN module “Aux” terminal. 2. Remove the Phillips PM2.0×4.0 screw (2) and the Phillips PM2.0×6.0 screw (3) that secure the WWAN module to the system boar d. (The WWAN module tilts up.) Component re placement procedures 45
3. Remove the WWAN mod ule (4) by pulling the module aw ay from the slot at an angle. NOTE: WWAN modules are des igned with a notch (5) to prevent incorrect insertion of the WWAN module into the WWAN module slot. Reverse this procedure to ins tall the WWAN module. 46 Chapter 4 Removal an d replacement procedures
WLAN module Description Spare part number Atheros 9285G 802.11b/g/n Half MiniCard 605560-001 Broadcom 4313/2070 802.11b/g/ n (1x1) and BT Half MiniCard 600370-001 Broadcom BCM94313HMG2L 802.11b/g/n (1x1) Half MiniCard 5938 36-001 Ralink RT3090 802.11b/g/n BC4 Bl uetooth PCI-e half MiniCard 602992-001 CAUTION: The WWAN module and the W LAN module ar e not interchangeable. To prevent an unresponsive system, replace the wireless mo dule only with a wireless module authorized for use in the computer by the govern mental agency that regulates wireless de vices in your country or region. If you replac e the module and then rece ive a warning message, remove the module to restore computer functionality, and then contact technical support thro ugh Help and Support. Before removing the WLAN module, follow these step s: 1. Shut down the computer. If you ar e unsure whether the computer is o ff or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external device s connected to the computer. 3. Disconnect the power from the de vice by first unplugging the powe r cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the battery (see Battery on page 38 ). 5. Remove the service cover (see Service cover on page 40 ). Remove the WLAN module: 1. Disconnect the WLAN antenna cables (1) from the terminals on the WLAN module. NOTE: The black WLAN antenna cable is connected to the WLAN module “Main” terminal . The white WLAN antenna cable is connected to the WLAN module “Aux” terminal. 2. Remove the two Phil lips PM2.0× 4.0 screw s (2) that secure the WLAN module to the system board. (The WLA N module tilts up.) Component re placement procedures 47
3. Remove the WLAN module (3) by pulling the module away from the slot at an a ngle. NOTE: WLAN modules are designed with a notch (4) to prevent incorrect insertion of the WLAN module into th e WLAN module slot. Reverse this procedure to install the WLAN module. 48 Chapter 4 Removal an d replacement procedures
Memory module Description Spare part number 1-GB memory module (667-MHz, DDR3) 615862-001 2-GB memory module (667-MHz, DDR3) 615863-001 1-GB memory module (667-MHz, DDR 3), WWAN 615864-0 01 2-GB memory module (667-MHz, DDR 3), WWAN 615865-0 01 Before removing the memory module, follow these step s: 1. Shut down the computer. If you ar e unsure whether the computer is o ff or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external device s connected to the computer. 3. Disconnect the power from the computer by firs t unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the battery (see Battery on page 38 ). 5. Remove the service cover (see Service cover on page 40 ). Remove the memory module: 1. Pull away the retention clips (1) on each side of the memor y module to release the memory module. (The memory module tilts up.) CAUTION: To prevent damage to the memory module, hold it by the edges on ly. Do not touch the components on the memory module. Component re placement procedures 49
2. Grasp the edge of the memory module (2) , and then pull it out of the memory module slot. NOTE: Memory modules are designed with a notch (3) to prevent incorrect insertion into the memory module slot. Reverse this procedure to install the memory module. 50 Chapter 4 Removal an d replacement procedures
RTC battery Description Spare part number RTC battery 599516-001 Before removing the real-time cloc k (RTC) battery, fo llow these step s: 1. Shut down the computer. If you ar e unsure whether the computer is o ff or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external device s connected to the computer. 3. Disconnect the power from the computer by firs t unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the battery (see Battery on page 38 ). 5. Remove the service cover (see Service cover on page 40 ). Remove the RTC battery: ▲ Remove the RTC b attery from the socke t on the syst em board. Reverse this procedure to install the RTC battery. When installing the RTC battery, make sure the “ ” sign faces up. Component re placement procedures 51
Keyboard NOTE: The keyboard spare p art kit includes a keyboard cable. For use in: Spare part number For use in: Spare part number In white: Belgium 607977-A41 The Netherlands 607977-B31 Brazil 607977-201 Portugal 607977-131 The Czech Republic 607977-221 Russia 60 7977-251 Denmark, Finland, and Norway 607977-DH1 Saudi Arabia 607977-171 France 607977-051 Slovenia 607977-BA1 French Canada 607977-121 South Korea 607977-AD1 Germany 607977-041 Spain 607977-071 Greece 607977-DJ1 Switzerland 607977-BG1 Hungary 607977-211 Taiwan 607977-AB1 Israel 607977-BB1 Thailand 607977-281 Italy 607977-061 Turkey 607977-14 1 Japan 607977-291 The United Kingdom 607977-031 Latin America 607977-161 The United States 607977-001 In pink: Belgium 607978-A41 The Netherlands 607978-B31 Brazil 607978-201 Portugal 607978-131 The Czech Republic 607978-221 Russia 60 7978-251 Denmark, Finland, and Norway 607978-DH1 Saudi Arabia 607978-171 France 607978-051 Slovenia 607978-BA1 French Canada 607978-121 South Korea 607978-AD1 Germany 607978-041 Spain 607978-071 Greece 607978-DJ1 Switzerland 607978-BG1 Hungary 607978-211 Taiwan 607978-AB1 Israel 607978-BB1 Thailand 607978-281 Italy 607978-061 Turkey 607978-14 1 Japan 607978-291 The United Kingdom 607978-031 Latin America 607978-161 The United States 607978-001 In black: 52 Chapter 4 Removal an d replacement procedures
For use in: Spare part number For use in: Spare part number Belgium 590527-A41 The Netherlands 590527-B31 Brazil 590527-201 Portugal 590527-131 The Czech Republic 590527-221 Russia 59 0527-251 Denmark, Finland, and Norway 590527-DH1 Saudi Arabia 590527-171 France 590527-051 Slovenia 590527-BA1 French Canada 590527-121 South Korea 590527-AD1 Germany 590527-041 Spain 590527-071 Greece 590527-DJ1 Switzerland 590527-BG1 Hungary 590527-211 Taiwan 590527-AB1 Israel 590527-BB1 Thailand 590527-281 Italy 590527-061 Turkey 590527-14 1 Japan 590527-291 The United Kingdom 590527-031 Latin America 590527-161 The United States 590527-001 Before removing the keyboard, follo w these steps: 1. Shut down the computer. If you ar e unsure whether the computer is o ff or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external device s connected to the computer. 3. Disconnect the power from the computer by firs t unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the battery (see Battery on page 38 ). 5. Remove the service cover (see Service cover on page 40 ). Component re placement procedures 53
Remove the keyboard: 1. Remove the three Phillips PM2.0×6.0 screw s that secure the keyboa rd to the computer. 2. Turn the computer right-side up, with the front toward you. 3. Open the computer as far as it will open. 4. Lift the rear edge of the keyboard (1) until it rests at an angle. 5. Slide the keyboard (2) back until t he keyboard cable and connector are accessible. 6. Release the zero ins ertio n force (ZIF) connector (3) to which the keyboard cable is atta ched, and then disconnect th e keyboa rd cable (4) from the system board. 7. Remove the keyboard. 54 Chapter 4 Removal an d replacement procedures
Reverse this procedure to install the keyboard. Component re placement procedures 55
Top cover NOTE: The top co ver includes the TouchP ad board and br acket. Description Spare part number In black, for use o nly with FF computer models 589676-001 In black, for use o nly with DF computer models 596144-001 In pink 608304-001 In white 608305-001 Before removing the top cover, fo llow these steps: 1. Shut down the computer. If you ar e unsure whether the computer is o ff or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external device s connected to the computer. 3. Disconnect the power from the computer by firs t unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the battery (see Battery on page 38 ). 5. Remove the service cover (see Service cover on page 40 ). 6. Remove the keyboard (see Keyboard on page 52 ). Remove the top cover. 1. Turn the computer upside down, with the front toward you. 2. Remove the six Phillips PM2.0×6.0 screw s (1) and the Phillips PM2.5×4.0 screw (2) that secure the top cover to the base enclo sure. 3. Turn the computer right-side up, with the front toward you. 4. Open the computer as far as it will open. 56 Chapter 4 Removal an d replacement procedures
5. Disconnect the speaker cable (1) from the system board. 6. Release the ZIF connecto r (2) to which the TouchPad cable is connected, and then disconnect the TouchPad cabl e (3) from the sy stem board. 7. Remove the fi ve Phillip s PM2.0× 6.0 screw s that secur e the top cover to the bas e enclosure . 8. Release the top cover (1) by lifting the rear edge until it disengages from the base enclosure. Component re placement procedures 57
9. Remove the top cover (2) by lifting it straight up. Reverse this procedure to install the top cover. 58 Chapter 4 Removal an d replacement procedures
Speakers Description Spare part number Speakers (include cables) 596153-001 Before removing the speakers, fo llow these steps: 1. Shut down the computer. If you ar e unsure whether the computer is o ff or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external device s connected to the computer. 3. Disconnect the power from the computer by firs t unplugging the power cord from the AC outlet and then unplugging the AC Adapter from the computer. 4. Remove the battery (see Battery on page 38 ). 5. Remove the following components: a. Service cover (see Service cover on page 40 ). b. Keyboard (see Keyboard on page 52 ). c. Top cover (see Top cover on page 56 ). Remove the speakers: 1. Turn the top cover upside down, with the front toward you. 2. Release the TouchPad cabl e (1) from the top co ver. (The Tou chP ad cable is attached to the top cover with double-sided adhesive). 3. Release the speaker cable from the clips (2) built into the TouchPad bracket. 4. Remove the two Phil lips PM2.0× 4.0 screw s (3) that secure the speakers to the top cover. 5. Remove the speakers (4) . Component re placement procedures 59
Reverse this procedure to install the speakers. 60 Chapter 4 Removal an d replacement procedures
Display assembly Description Spare part number 25.7-cm (10.1-in) display assembly (includes display panel cable, 2 WLAN transcei vers and cables, 2 WWAN transceivers and cables, and we bcam/microphone mo dule and cable): For use only with HP Mini 2102 and 210 com puter models: ● HD, flush glass display assembly in black 612201-001 ● HD, flush glass dis play assembly in blue 612199-001 ● HD, flush glass display assem bly in red 612203-001 ● HD, flush glass display assembly in silver 612197-001 ● WSVGA, flush glass display assembly in black 612200-001 ● WSVGA, flush glass display assembly in blue 612198-001 ● WSVGA, flush glass display assembly in red 612202-001 ● WSVGA, flush glass display assembly in silver 612196-001 ● WSVGA, AntiGlare, flus h glass display assembly in pink 605040-001 ● HD, AntiGlare, flush glas s display assembly in pink 60 5041-001 25.7-cm (10.1-in), WSVGA, AntiGlare, standard disp lay assembly in white for use only with HP Mini 2102 and 210 computer models 605039-001 25.7-cm (10.1-in), WSVGA, AntiGlare, standard di splay assembly in black for use only with Compaq Mini 210 computer models 589649-001 Before removing the display assembly, follow these s teps: 1. Shut down the computer. If you ar e unsure whether the computer is o ff or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external device s connected to the computer. 3. Disconnect the power from the computer by firs t unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the battery (see Battery on page 38 ). 5. Remove the service cover (see Service cover on page 40 ). 6. Disconnect the WWAN antenna cables from the WWAN module ( see WWAN module on page 45 ). 7. Disconnect the WLAN antenna cabl es from the WLAN module (see WLAN module on page 47 ). 8. Remove the keyboard (see Keyboard on page 52 ). 9. Remove the top cover (see Top cover on page 56 ). Component re placement procedures 61
Remove the display assembly: 1. Close the computer . 2. Turn the computer upside down, with the front toward you. 3. Release the WLAN an tenna cables (1) from the clips built into the base enclo sure (2) . 4. Turn the computer right-side up, with the front toward you. 5. Open the computer as far as it will open. 6. Disconnect the display panel cable (1) from the system boar d. 62 Chapter 4 Removal an d replacement procedures
7. Release the wirele ss antenna cables (2) from the clip built into the base enclosure. CAUTION: Support the display assembly when removing the following screws. Failure to support the display assembly can result in da mage to the display assembly and other devic e componen ts. 8. Remove the two Phil lips PM2.0× 4.0 screw s (1) that secure the display assembly to the base enclosure. 9. Remove the display assembly (2) . Reverse this procedure to reassemble and install the display assemb ly. Component re placement procedures 63
System board NOTE: The system board spare p art kit includes re placement thermal material. Description Spare part number Intel® Atom™ N455 1.66-GHz processor, 5 12-KB level 2 cache, 667-M Hz front-side bus (FSB) 608951-001 Intel® Atom™ N455 1.66-GHz processor, 5 12-KB le vel 2 cache, 667-M Hz front-side bus (FSB), decoder ring, WWAN 608952-001 Intel® Atom™ N455 1.66-GHz processor, 5 12-KB le vel 2 cache, 667-M Hz front-side bus (FSB), Broadcom FLEA 608953-001 Intel® Atom™ N455 1.66-GHz processor, 5 12-KB le vel 2 cache, 667-M Hz front-side bus (FSB), decoder ring, Broadcom FLEA, WWAN 608954-001 Intel® Atom™ N475 1.83-GHz processor, 5 12-KB level 2 cache, 667-MHz FSB, 6.5 W TDP 608955-001 Intel® Atom™ N475 1.83-GHz processor, 5 12-KB level 2 cache, 667-MHz FSB, 6.5 W TDP, decoder ring, WWAN 608956-001 Intel® Atom™ N475 1.83-GHz processor, 5 12-KB level 2 cache, 667-MHz FSB, 6.5 W TDP, Broadcom FLEA 608957-001 Intel® Atom™ N475 1.83-GHz processor, 5 12-KB level 2 cache, 667-MHz FSB, 6.5 W TDP, decoder ring, Broadcom FLEA, WWAN 608958-001 Before removing the sys tem board, fo llow these steps: 1. Shut down the computer. If you ar e unsure whether the computer is o ff or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external device s connected to the computer. 3. Disconnect the power from the computer by firs t unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the battery (see Battery on page 38 ). 5. Remove the service cover (see Service cover on page 40 ). 6. Disconnect the hard drive cabl e f rom the system board (see Hard drive on page 43 ). 7. Disconnect the WWAN antenna cables from the WWAN module ( see WWAN module on page 45 ). 8. Disconnect the WLAN antenna cabl es from the WLAN module (see WLAN module on page 47 ). 9. Remove the keyboard (see Keyboard on page 52 ). 10. Remove the top cover (see Top cover on page 56 ). 64 Chapter 4 Removal an d replacement procedures
When replacing the system board, be sure that the foll owing compone nts are removed from the defective system board and installe d on the replac ement system board: ● SIM (see SIM on page 39 ) ● WWAN module (see WWAN module on page 45 ) ● WLAN module (see WLAN module on page 47 ) ● Memory module (see Memory module on page 49 ) ● RTC battery (see RTC battery on page 51 ) ● Fan/heat sink assembly (see Fan/heat sink assembly on page 67 ) Remove the system board: 1. Disconnect the display panel cable (1) from the system boar d. 2. Disconnect the power connector cable (2) from the system board. 3. Remove the Phillips PM2.0×4.0 screw (1) that secu res the system boa rd to the base enc losure. 4. Lift the right side of the system board (2) unti l it rests a t an angle. Component re placement procedures 65
5. Remove the system board (3) by sliding it up and away from the base enclosure. Reverse the procedure to in stall the system board. 66 Chapter 4 Removal an d replacement procedures
Fan/heat sink asse mbly Description Spare part number Fan/heat sink assembly (in cludes replacement thermal material) 589681-001 NOTE: To properly ventilate the comput er, allow at least a 7.6-c m (3-inch) clearanc e on the left side of the computer. The computer us es an electric fan for ventilation. The fan is controlled by a temperature sensor and is de signed to tur n on au tomatically when high temp erature conditions exis t. These conditions are af fected by high externa l temperatures, s ystem power consumption, power management/battery conser vation configurations, battery fast charging, and software requirement s. Exhaust air is displaced through the ventilation gr ill located on the left side of the computer. Before removing the fan/heat si nk assembly, follow these steps: 1. Shut down the computer. If you ar e unsure whether the computer is o ff or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external device s connected to the computer. 3. Disconnect the power from the computer by firs t unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the battery (see Battery on page 38 ). 5. Remove the service cover (see Service cover on page 40 ). 6. Disconnect the hard drive cabl e f rom the system board (see Hard drive on page 43 ). 7. Disconnect the WWAN antenna cables from the WWAN module ( see WWAN module on page 45 ). 8. Disconnect the WLAN antenna cabl es from the WLAN module (see WLAN module on page 47 ). 9. Remove the following components: a. Keyboard (see Keyboard on page 52 ). b. Top cover (see Top cover on page 56 ). c. System board (see System bo ard on page 64 ). Remove the fan/heat sink assembly: 1. Turn the system bo ard upside do wn, with the front toward you. 2. Disconnect the fan cable (1) from the system boar d. 3. Following the 1, 2, 3 sequence st amped into the fa n/heat sink as semb ly, loosen the three Phillip s PM2.0×4.0 captive screws (2) that secure the fan/heat sink assembly to the system board. Component re placement procedures 67
4. Remove the fan/heat sink assembly (3) . NOTE: Due to the adhesive quality of the thermal material located between the fan/heat sink assembly and system board components, it may be necessary to move the fan/heat sink assembly from side to side to detach it from the system board. NOTE: The thermal material must be thoroughly clea ned from the surfaces of the fan/heat sink assembly and the system board each time the fan/he at sink assembly is re moved: Thermal paste is used on the processor (1) and the fan/heat sink assembly section (2) that services it. Reverse this procedure to install the fan/heat sink assembly. 68 Chapter 4 Removal an d replacement procedures
Power connector cable Description Spare part number Power connector cable 589682-001 Before removing the power connect or cable, follow these s teps: 1. Shut down the computer. If you ar e unsure whether the computer is o ff or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external device s connected to the computer. 3. Disconnect the power from the computer by firs t unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the battery (see Battery on page 38 ). 5. Remove the service cover (see Service cover on page 40 ). 6. Disconnect the hard drive cabl e f rom the system board (see Hard drive on page 43 ). 7. Disconnect the WWAN antenna cables from the WWAN module ( see WWAN module on page 45 ). 8. Disconnect the WLAN antenna cabl es from the WLAN module (see WLAN module on page 47 ). 9. Remove the following components: a. Keyboard (see Keyboard on page 52 ). b. Top cover (see Top cover on page 56 ). c. Display assembly (see Display assembly on page 61 ). d. System board (see System bo ard on page 64 ). Remove the power co nnector cable: 1. Remove the Phillips PM2.0×4.0 screw (1) that secures the power co nnector and bracket to the base enclosure. 2. Remove the power connector bracket (2) . NOTE: The power connector bracket is in cluded in the base enclosure spare part kit, spare part number 608306-0 01. Component re placement procedures 69
3. Remove the power connector cable (3) . Reverse this procedure to install the power connector cable. 70 Chapter 4 Removal an d replacement procedures
5 Setup Utility Starting Setup Utility Setup Utility is a ROM-based information and custom ization utility that c an be used even when your Windows operating system is not working. The utility reports information about the computer and provides settings for startup, secur ity, and other preferences. To start Setup Utility: ▲ Open Setup Utility by turning on or restarting the computer, and then pressing f10 while the “F10 = BIOS Setup Options” message is displayed in the lower-left corner of the screen. Using Setup Utility Changing the language of Setup Utility The following procedur e explains how to change the la nguage of Setup Utility. If Setup Utility is not already running, begin at step 1. If Setup Utility is already running, begi n at step 2. 1. Open Setup Utility by turning on or restarting the computer, and then pressing f10 while the “F10 = BIOS Setup Options” message is displayed in the lower-left corner of the screen. 2. Use the arrow keys to select System Configuration > Language , and then press enter . 3. Use the arrow keys to select a language, and then press enter . 4. When a confirmation prompt with your language selected is displayed, press enter . 5. To save your change and exit Setup Ut ility, use the arrow keys to select Exit > Exit Saving Changes , and then press enter . Your change goes into effect immediately. Your change goes into effect immediately. Starting Setup Utility 71
Navigating and selecting in Setup Utility Because Setup Utility is not Windows based, it does not support the To uchPad. Na vigation and selection are by keystroke. ● To choose a menu or a menu item, use the arrow keys. ● To choose an item in a list or to toggle a field, for example an Enable/Disable f ield, use either the arrow keys or f5 or f6 . ● To select an item, press enter . ● To close a text box or return to the menu display, press esc. ● To display additional navigation and selection information while Setup Utility is open, press f1 . Displaying system information The following procedure explains how to display system information in Setup Utility. If Setup Utility is not open, begin at step 1. If Setup Utility is open, begin at step 2. 1. Open Setup Utility by turning on or restarting the computer, and then pressing f10 while the “F10 = BIOS Setup Options” message is displayed in the lower-left corner of the screen. 2. Select the Main menu. System information such as the system time and date, an d identification information about the computer is displayed. 3. To exit Setup Utility without changing any settings, use the arrow keys to select Exit > Exit Discarding Changes , and then press enter . Restoring default settings in Setup Utility The following procedure explain s how to restore the Se tup Utility default settings. If Setup Utility is not already running, begin at step 1. If Setup Utility is already running, begi n at step 2. 1. Open Setup Utility by turning on or restarting the computer, and then pressing f10 while the “F10 = BIOS Setup Options” message is displayed in the lower-left corner of the screen. 2. Use the arrow keys to select Exit > Load Setup Defaults , and then press ente r . 3. When the Setup Confirmati on is displayed, press enter . 4. To save your change and exit Setup Ut ility, use the arrow keys to select Exit > Exit Saving Changes , and then press enter . The Setup Utility default settings go in to effect when the computer restarts. NOTE: Your password, security, and language settings are not changed when you restore the factory default settings. 72 Chapter 5 Setup Utility
Exiting Setup Utility You can exit Setup Utility with or without saving changes. ● To exit Setup Utility and save your changes from the cu rrent session: If the Setup U tility menus are not vis ible, press es c to return to the menu display. Then use the arrow keys to select Exit > Exit Saving Changes , and then press enter . ● To exit Setup Utility without saving your change s from the current sessio n: If the Setup U tility menus are not vis ible, press es c to return to the menu display. Then use the arrow keys to select Exit > Exit Discarding Changes , and then press enter . After either choice, the computer res tarts in Windows. Setup Utility Menus Main Menu The menu tables in this section provide an overview of the Setup Utility options NOTE: Some of the Setup Utility menu items l isted in this chapter may not be supported by your computer. Select To do this System information ● View and change the system time and date. ● View identification information about the co mputer. ● View specification information about the processor, memory size, and system BIOS. Security Menu Select To do this Administrator password Enter, change, or delete an administrator password. Power-On password Enter, change, or delete a power-on password. Exiting Setup Utility 73
System Configuration Menu Select To do this Language Support Change th e Setup Utility language. Processor C4 State Enable/disable the processor C4 standby state. Boot Options Set the following boot options: ● f10 and f12 Delay (sec. ) ― Set the delay for the f10 and f12 functions of Setup Utility in intervals of 5 seconds each (0, 5, 10, 15, 20). ● HP QuickWeb ― Enable/disable the QuickWeb Boot menu in Setup Utility. ● Internal Network Adapter boot ― Enable/disable boot from Internal Network Adapter. ● Boot Device Priority ― Set the boot device priority for: ◦ Internal hard drive (select models only) ◦ USB Floppy ◦ USB CD/DVD ROM Drive ◦ USB flash drive ◦ USB Hard drive ◦ USB Card Reader ◦ Network adapter NOTE: Only the devices attached to th e system will appear in the boot order menu. Diagnostics M enu Select To do this Hard Disk Self Test (select mo dels only) Run a comprehensive self-test on th e hard drive. Memory Test Run a diagnostic test on the system memory . 74 Chapter 5 Setup Utility
6 Backup and recovery (Windows only) Windows 7 To protect your information, bac k up your files and folders. In ca se of system failure, you can use the backup files to res tore your co mputer. CAUTION: In the event of a hard drive failure, you ca nnot use your computer to access the Disaster Recovery utility. Therefore, HP recommends that you download the Di saster Recovery utility SoftPaq, and then extract it to a USB flash drive as soon as possible aft er soft ware setup. For details, refer to “Downloading and extracting the Disaster Recovery utility” later in this section. Depending on your computer model, you may ha ve one of the following backup and recovery solutions: ● Roxio BackOnTrack ● HP Recovery Manager NOTE: For detailed information, perfo rm a search for these topics in Help and Support. Backing up and recovering using Roxio BackOnTrack Successful recovery after a system failure depends on whether you have completely backed up your files. If Roxio BackOnTrack is prei nstalled on your computer, it allows you to create a backup of your computer image. You should create the initial back up immediately after software setup. As you add new software and data files, you should continue to back up your system on a regu lar basis to maintain a reasonably current backup. Note the following guidelines when backing up yo ur information: ● Store personal files in the Documents li brary and back up this folder regularly. ● Back up templates stored in their associated programs. ● Save customized settings in a window, too lbar, or menu bar by taking a sc reen shot of your settings. The screen sho t can be a time-saver if you have to reset your preferences. Window s 7 75
To copy the screen and paste it into a word-p rocessing document, fo llow these st eps: 1. Display the screen. 2. Copy the screen: To copy the active window, pres s alt prt sc . To copy the entire screen, press prt sc . 3. Open a word-processing document, click Edit , and th en click Paste . 4. Save the document. Creating a copy of the hard drive The back up drive func tion of BackOnTrack cre ates a Disaster Recovery Set that is an exact image of your hard drive data. You can back up t he image to an external hard drive (pu rchased separately) . To create a Disaster Re covery Set using BackOnTrack, follow these s teps: NOTE: Be sure that the computer is connected to AC power before you start the backup process. 1. Click Start , click All Programs , and then click Roxio . 2. Click BackOnTrack , c lick BackOnTrack Home , and then click Disaster Recovery . 3. Click Backup drive . 4. Select a drive to back up. 5. Add a comment to describe the backup . NOTE: Comments are optional, but adding comments can help you rememb er the purpose of the backup. The date and list of drives being backed up are a utomatically included in t he description. 6. Select a destination for the Disaster Rec overy Set. NOTE: The destination cannot be a netwo rk drive. 7. Click the action button at the bott om-right of the compute r screen. 8. Follow the on-screen instructio ns. Performing a recovery In case of system failure or inst ability, the computer prov ides the following ways to recover your files: ● BackOnTrack Disaster Recovery utility: You can us e Disaster Recovery to recover your hard drive image (includin g your files, progra ms, and operatin g system) after a hard dr ive failure. ● BackOnTrack Instant Restore utility: You can use In stant Restore to quickly restore your computer to a working state if a software-r elated proble m occurs. The Inst ant Restore utility auto matically creates working states pe riodically. You can also define a working state by saving the current computer state manually. For more informatio n about computer syste m states, refer to th e BackOnTrack software Help. 76 Chapter 6 Backup and reco very (Windows only)
Using the Disaster Recovery utility NOTE: To perform a recovery with Disaste r Recovery , you need a USB fl ash drive (purch ased separately). For optimum performa nce, the capacity of the drive sh ould be no larger than 2 GB. Disaster Recovery re covers data from a Disa ster Re covery Set t hat you previously created with Roxio BackOnTrack. Disas ter Recovery is available from the HP Web si te in a compressed file called a SoftPaq. NOTE: Running the SoftPaq makes the USB drive bootable. Before performing a disaster recove ry, you must download the Disaster Recovery utility and extract it to a USB flash drive. Downloading and extracting th e Disaster Recovery utility To download and ex tract Disaster Recovery, follow these steps: 1. Connect a bootable USB flash drive or extern al drive to a USB port on your computer. 2. Open your Web browser, go to http://www.hp.com/ support , and select your country or region. 3. Enter the SoftPaq numbe r SP42226 in the Search box, press enter , and then follow the on-screen instructions. 4. Click Download only to save the file to your computer. 5. When prompted, click Save , and then select the external drive from the list of storage locations. 6. After the file is download ed, navigate to the USB flash drive or external drive, and then double- click the SoftPaq file to f ormat the USB flash drive and extrac t the Disaster Recovery files. 7. If prompted to do so, resta rt your comp uter after the installation is complete. Restoring your hard drive image To restore your hard drive image usin g Disaster Recovery, follow these steps : 1. Connect the external hard drive containing th e Disaster Recovery Set to your computer. 2. Connect the bootable USB flash drive containing th e extracted Disaster Recovery utility t o a USB port on your com puter. 3. Change the boot device order by turning on or restarting the computer, and then pressing f9 . 4. Use the arrow keys to select the USB flash drive, and then press enter . 5. At the Roxio BackOnTr ack Disaster Recovery scre en, select Disaster Recove ry , and then click Next . 6. Browse to the external hard drive containing the Disaster Recovery Set, and then click Next . 7. Click Next to proceed with the recovery. NOTE: This process may take several minutes. 8. After a message on the scree n reports a successf ul recovery , click Finish . Window s 7 77
Using the Instant Restore utility You can restore your computer from Windows when the operating system is functioning. If th e operating system is not functioning, you can also access the utility by re starting y our computer. NOTE: For more informat ion about the In stant Restore utility, refer to the BackOnT rack soft ware Help. Using the Instant Restore utility when the operating system is functioning To recover information when the operating system is functioning properly, follow these steps: 1. Save and close al l open documents a nd close any ope n programs. 2. Click Start , click All Programs , and then click Roxio . 3. Click BackOnTrack , c lick BackOnTrack Home , and then click Instant Restore . 4. Click Restore S tate , and then select a restore stat e. 5. Click the action button in the bottom-r ight corner of the co mputer screen. 6. Click Yes to confirm your selected restore state. When the restore process is complete , the computer restarts and a not ification message is displayed. Using the Instant Restore utility when th e operating system is not functioning To recover information when the operating syst em is not function ing, follow these steps: 1. Restart the computer. NOTE: If the operating system has sto pped responding and the computer screen is blue, restart the computer by turning the power switch off and then on. 2. When the computer logo is displayed on the screen, press f6 repeatedly until the Windows status bar is displayed. 3. When the Roxio BackOnT rack screen is di splayed, follow the on-screen instructions. Using Windows Backup and Restore To create a backup us ing Windows Back up and Restore, follow these steps: NOTE: Be sure that the computer is connected to AC power before you start the backup process. NOTE: The backup process may take over an hour, de pending on file size and the speed of the computer. 1. Click Start , click All Programs , click Maintenance , and then click Backup and Restore . 2. Follow the on-screen instructions to set up and create a backup. NOTE: Windows incl udes the User Account Contro l feature to improve the security of your computer. You may be prompted for your permis sion or password for tas ks such as installing software, running utilities, or changing Windows settings. Refer to Help and Suppor t for more information. 78 Chapter 6 Backup and reco very (Windows only)
Using system restore points When you back u p your system, you are c reating a system restore point. A system restore point allows you to save and name a snapshot of your hard driv e at a specific point in tim e. You can then revert back to that point if you wa nt to reverse subsequent ch anges made to your system. NOTE: Recovering to an earlier restore point does not affect data files saved or e-mails created since the last restore p oint. You also can create additional restore point s to pr ovide increased protection for your system files and settings. When to create restore points ● Before you add or extensively modify software or hardwar e. ● Periodically, wheneve r the syst em is performing optimally. NOTE: If you revert to a restore point and then chan ge your mind, you can rever se the restoration. Creating a system restore point 1. Click Start , click Con trol Pane l , click System and Security , an d then click System . 2. In the left pane, click System protection . 3. Click the System P rotection tab. 4. Under Protection Settings , select the disk for which you want to create a restore point. 5. Click Cr eate . 6. Follow the on-screen instructio ns. Restoring to a previous date and time To revert to a restore point (created at a previou s date and time) when the computer was functioning optimally, follow these s teps: 1. Click Start , click Con trol Pane l , click System and Security , an d then click System . 2. In the left pane, click System protection . 3. Click the System P rotection tab. 4. Click System Restore . 5. Follow the on-screen instructio ns. Window s 7 79
Backing up and recovering using HP Recovery Manager If your computer includes HP Recovery Manager, tools provided by the operating system and by HP Recovery Manager software are des igned to help you with the foll owing tasks for safeguarding y our information and restoring it in case of a system failure: ● Backing up your information ● Creating a set of recovery discs ● Creating system restore p oints ● Recovering a program or driver ● Performing a full system recovery Backing up your information As you add new software and data files , you should back up your sy stem on a regular basis to maintain a reasonably current backup. Back up your system at the following times: ● At regularly scheduled times NOTE: Set reminders to back up yo ur information periodically. ● Before the compu ter is repaired or restore d ● Before you add or modify hardware or software Note the following when backing up: ● Create system restore points us ing the Windows System Restore feature, and period ically copy them to a disc. ● Store personal files in the Do cuments library, and periodically back up this folder. ● Back up templates stored in their associated programs. ● Save the customized settings in a window, too lbar, or menu bar by taking a sc reen shot of the settings. The screen sho t can be a time-saver if you have to reset your preferences. To copy the sc reen and paste the im age into a word-processing document: 1. Display the screen. 2. Copy the scre en: To copy only the active window, press alt prt sc . To copy the entire screen, press prt sc . 80 Chapter 6 Backup and reco very (Windows only)
3. Open a word-processing document, click Edit , and th en click Paste . 4. Save the document. ● You can back up your information to an optional ext ernal hard drive, a network drive, or discs. ● When backing up to discs, use any of the follow ing types of disc s (purchased sepa rately): CD-R, CD-RW, DVD R, DVD-R, or DVD±RW . The discs you use depend on the type of optical drive you are using. NOTE: The external optical drive must be connected to the USB port on the computer , not to a USB port on another externa l device , such as a hub or docking station. NOTE: DVDs store more infor mation than CDs, so using them for backup reduces the number of recovery discs required. ● When backing up to disc s, number each disc before inserting it into an optical drive. Creating a set of recovery discs HP recommends that you create recove ry discs to be sure that you can restor e your system to its original factory state if you experie nce serious system f ailure or instability. Create these discs after setting up the computer for the first time. NOTE: This task will require an optional external op tical drive. The external optical drive must be connected to the USB port on the computer , not to a USB port on another external device, such as a hub or docking station. Handle these discs carefully and keep them in a safe plac e. The soft ware allows the creation of only one set of recovery disc s. Note the following guidelines before creating recovery discs: ● You will need high-quality DVD-R, DVD R, BD-R (wri table Blu-ray), or CD-R discs. All these discs are purchased separately. DVDs have a larger st orage capacity than CDs. If you use CDs, up to 20 discs may be required, whereas only a few DVDs are required. NOTE: Double-layer discs and re ad-write d iscs—such as CD-RW, DVD±RW, and BD-RE (rewritable Blu-ray) discs—are not compatib le with the Recovery Manager software. ●  The computer must be c onnected to AC power during this process. ●  Only one set of recovery discs can be created per computer. ●  Number each disc before inse rting it into an optical drive. ● If necessary, you ca n exit the progra m before you have f ini shed creating the recovery discs. The next time you open Recovery Manager, you will be prompted to co ntinue the disc cre ation process. To create a set of recovery discs: 1. Click Start , click All Programs , click Recovery Manager , and then click Recovery Disc Creation . 2. Follow the on-screen instructio ns. Window s 7 81
Performing a re covery NOTE: You can recover only files that yo u have prev iously backed up. HP re commends that you use Recovery Manager to create a set of recovery discs (entire drive ba ckup) as soon as yo u set up your computer. Recovery Manager software allows you to repair or restore the sy stem if you experience system failure or instability. Recovery Manager works from reco very discs that you crea te or fr om a dedicated recovery partition (select models only) on the har d drive. Howeve r, computers that include a sol id-state drive (SSD) may not have a recovery partition. If th at is t he case, recovery discs have been included with your computer. Us e these discs to re cover your operating system and software. NOTE: Windows has its own built- in repair features, such as System Restore. If you have not al ready tried these features, try them befo re using Recover y Manager. For more information on these built-in repair features, click Start , and then click Help and Support . NOTE: Recovery Manager recovers only the software that was preinstalled at the factory. Software not provided with this computer must be downloade d from the manufacturer’s Web site or reinstalled from the disc provided by the manufacturer. Recovering using the recovery discs To restore the system file s from the recovery discs: 1. Back up all personal files. 2. Insert the first recovery disc into an opti onal optic al drive, and re start the computer. NOTE: The external optical drive must be con nected to the USB port on the computer , not to a USB port on another external device , such as a hub or docking station. 3. Follow the on-screen instructio ns. Recovering using the partition on th e hard drive (select models only) On some models, you can perform a recovery from th e partition on th e hard drive, which is acces sed by pressing either the Start button or f11 . This restores the computer to its factory condition. NOTE: This method of recovery is also an HP Recovery Manager solution. NOTE: Computers with an SSD may not ha ve a recovery partition. If the computer does not have a recovery partition, you will not be able to recover using this procedure. Recovery discs have been included for computers that do not have a partitio n. Use these discs to recover your o perating system and software. To restore the system from the partition, follow these ste ps: 1. Access Recovery Manager in either of the following ways: ● Click Start , click All P rogra ms , click Recovery Manager , and then cl ick Recovery Manager . 82 Chapter 6 Backup and reco very (Windows only)
– or – a. Turn on or restart the computer. b. Press f11 while the “Press <F11> for recovery” message is displayed on the sc reen. NOTE: It may take se veral mi nutes for R ecovery Manag er to load. 2. In the Recovery Manager window , click System Recove ry . 3. Follow the on-screen instructio ns. Windows XP To protect your information, bac k up your files and folders. In ca se of system failure, you can use the backup files to res tore your co mputer. CAUTION: In the event of a hard drive failure, you ca nnot use your computer to access the Disaster Recovery utility. Therefore, HP recommends that you download the Di saster Recovery utility SoftPaq, and then extract it to a USB flash drive as soon as possible aft er soft ware setup. For details, refer to “Downloading and extracting the Disaster Recovery utility” later in this section. NOTE: For detailed information, perfo rm a search for these topics in Help and Support. Backing up your information Successful recovery after a system failure depends on whether you have completely backed up your files. If Roxio BackOnTrack is prei nstalled on your computer, it allows you to create a backup of your computer image. You should create the initial back up immediately after software setup. As you add new software and data files, you should continue to back up your system on a regu lar basis to maintain a reasonably current backup. Note the following guidelines when backing up yo ur information: ● Store personal files in the My Documents folder and back up this folder regularly. ● Back up templates stored in their associated programs. ● Save customized settings in a window, too lbar, or menu bar by taking a sc reen shot of your settings. The screen sho t can be a time-saver if you have to reset your preferences. To copy the screen a nd paste it into a wo rd-processing document, follow these steps: 1. Display the screen. 2. Copy the scre en: To copy the active window, press alt prt sc . To copy the entire screen, press prt sc . 3. Open a word-processing document, click Edit , and th en click Paste . 4. Save the document. Windows XP 83
Creating a copy of the hard drive The back up drive func tion of BackOnTrack cre ates a Disaster Recovery Set that is an exact image of your hard drive data. You can back up t he image to an external hard drive (pu rchased separately) . To create a Disaster Re covery Set using BackOnTrack, follow these s teps: NOTE: Be sure that the computer is connected to AC power before you start the backup process. 1. Click Start , click All Programs , and then click Roxio . 2. Click BackOnTrack , c lick BackOnTrack Home , and then click Disaster Recovery . 3. Click Backup drive . 4. Select a drive to back up. 5. Add a comment to describe the backup . NOTE: Comments are optional, but adding comments can help you rememb er the purpose of the backup. The date and list of drives being backed up are a utomatically included in t he description. 6. Select a destination for the Disaster Rec overy Set. NOTE: The destination cannot be a netwo rk drive. 7. Click the action button at the bott om-right of the compute r screen. 8. Follow the on-screen instructio ns. Performing a recovery In case of system failure or inst ability, the computer prov ides the following ways to recover your files: ● BackOnTrack Disaster Recovery utility: You can us e Disaster Recovery to recover your hard drive image (includin g your files, progra ms, and operatin g system) after a hard dr ive failure. ● BackOnTrack Instant Restore utility: You can use In stant Restore to quickly restore your computer to a working state if a software-r elated proble m occurs. The Inst ant Restore utility auto matically creates working states pe riodically. You can also define a working state by saving the current computer state manually. For more informatio n about computer syste m states, refer to th e BackOnTrack software Help. 84 Chapter 6 Backup and reco very (Windows only)
Using the Disaster Recovery Utility NOTE: To perform a recovery with Disaste r Recovery , you need a USB fl ash drive (purch ased separately). For optimum performa nce, the capacity of the drive sh ould be no larger than 2 GB. Disaster Recovery re covers data from a Disa ster Re covery Set t hat you previously created with Roxio BackOnTrack. Disas ter Recovery is available from the HP Web si te in a compressed file called a SoftPaq . NOTE: Running the SoftPaq makes the USB drive bootable. Before performing a disaster recove ry, you must download the Disaster Recovery utility and extract it to a USB flash drive. Downloading and extracting th e Disaster Recovery utility To download and ex tract Disaster Recovery, follow these steps: 1. Connect a bootable USB flash drive or extern al drive to a USB port on your computer. 2. Open your Web browser, go to http://www.hp.com/ support , and select your country or region. 3. Enter the Soft Paq number SP 42226 in the Se arch box, press enter , and then follow the on-screen instructions. 4. Click Download only to save the file to your computer. 5. When prompted, click Save , and then select the external drive from the list of storage locations. 6. After the file is download ed, navigate to the USB flash drive or external drive, and then double- click the SoftPaq file to f ormat the USB flash drive and extrac t the Disaster Recovery files. 7. If prompted to do so, resta rt your comp uter after the installation is complete. Restoring your hard drive image To restore your hard drive image usin g Disaster Recovery, follow these steps : 1. Connect the external hard drive containing th e Disaster Recovery Set to your computer. 2. Connect the bootable USB flash drive containing th e extracted Disaster Recovery utility t o a USB port on your com puter. 3. Change the boot device order by turning on or restarting the computer, and then pressing f9 . 4. Use the arrow keys to select the USB flash drive, and then press enter . 5. At the Roxio BackOnTr ack Disaster Recovery scre en, select Disaster Recove ry , and then click Next . 6. Browse to the external hard drive containing the Disaster Recovery Set, and then click Next . 7. Click Next to proceed with the recovery. This process may ta ke sever al minutes. 8. After a message on the scree n reports a successf ul recovery , click Finish . Windows XP 85
Using the Instant Restore utility You can restore your computer from Windows when the operating system is functioning. If th e operating system is not functioning, you can also access the utility by re starting y our computer. NOTE: For more informat ion about the In stant Restore utility, refer to the BackOnT rack soft ware Help. Using the Instant Restore utility when the operating system is functioning To recover information when the operating system is functioning properly, follow these steps: 1. Save and close al l open documents a nd close any ope n programs. 2. Click Start , click All Programs , and then click Roxio . 3. Click BackOnTrack , c lick BackOnTrack Home , and then click Instant Restore . 4. Click Restore S tate , and then select a restore stat e. 5. Click the action button in the bottom-r ight corner of the co mputer screen. 6. Click Yes to confirm your selected restore state. When the restore process is complete , the computer restarts and a not ification message is displayed. Using the Instant Restore utility when th e op erating system is not function ing To recover information when the operating syst em is not function ing, follow these steps: 1. Restart the computer. NOTE: If the operating system has sto pped responding and the computer screen is blue, restart the computer by turning the power switch off and then on. 2. When the computer logo is displayed on the screen, press f6 repeatedly until the Windows status bar is displayed. 3. When the Roxio BackOnT rack screen is di splayed, follow the on-screen instructions. 86 Chapter 6 Backup and reco very (Windows only)
7 Connector pin assignments Audio-in (microphone) Pin Signal 1 Audio signal in 2 Audio signal in 3G r o u n d Audio-out (headphone) Pin Signal 1A u d i o o u t , l e f t c h a n n e l 2 Audio out, right channel 3G r o u n d Audio-i n (microp hone) 87
External monitor Pin Signal 1 Red analog 2 Green analog 3 Blue analog 4N o t c o n n e c t e d 5G r o u n d 6 Ground analog 7 Ground analog 8 Ground analog 9 5 VDC 10 Ground 11 Monitor detect 12 DDC 2B data 13 Horizontal sync 14 Vertical sync 15 DDC 2B clock 88 Chapter 7 Conne ctor pin assignments
RJ-45 (network) Pin Signal 1 Transmit 2 Transmit - 3 Receive 4U n u s e d 5U n u s e d 6 Receive - 7U n u s e d 8U n u s e d Universal Serial Bus Pin Signal 1 5 VDC 2D a t a 3 Data 4G r o u n d RJ-45 (network) 89
8 Power cord set requirements The wide-range input feature of the computer permit s it to operate fr om any line voltage fr om 100 to 120 volts AC, or from 220 to 240 volts AC The 3-conductor power cord set in cluded with the computer me ets the requiremen ts for use in the country or region where the equipment is purchased. Power cord sets for use in other countries and reg ions must meet the requirements of the country or region where th e computer is used. Requirements for all countries The following require ments are applic able to all countries an d regions: ● The length of the power cord set must be at least 1.5 m (5.0 ft) and no more than 2.0 m (6.5 ft). ● All power cord se ts must be approved by an acceptable accredited agency responsible for evaluation in the country or region wh ere the pow er cord set will be u sed. ● The power cord sets mu st have a minimum current capacity of 10 amps and a nominal voltage rating of 125 or 2 50 V AC, as required by the power system of each country or region. ● The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC 320 Standard Sheet C13 connector for mating with the appliance inlet on the back of the computer. 90 Chapter 8 Power cord set requirements
Requirements for specific countries and regions Country/region Accredited agency Applicable note number Australia EANSW 1 Austria OVE 1 Belgium CEBC 1 Canada CSA 2 Denmark DEMKO 1 Finland FIMKO 1 France UTE 1 Germany VDE 1 Italy IMQ 1 Japan METI 3 The Netherlands KEMA 1 Norway NEMKO 1 The People's Republic of China COC 5 South Korea EK 4 Sweden SEMKO 1 Switzlerland SEV 1 Taiwan BSMI 4 The United Kingdom BSI 1 The United States UL 2 1. The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conducto r si ze. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency respons ible for evaluation in the country or region where it will be used. 2. The flexible cord mu st be Type SPT-3 or equivalent, No. 18 AWG, 3-conductor. The wall plug mus t be a two-pole grounding type with a NE MA 5-15P (15 A, 125 V) or NE MA 6-15P (15 A, 250 V) configuration. 3. The appliance coupler, flexible cord, and wall plug must bear a “T” mark and registration nu mber in accordance with the Japanese Dentori Law. The flexible cord must be Type VCT or VCTF, 3-conductor, 1.00-mm² conductor size. The wal l plug must be a two-pole grounding type with a Japanese In dustrial Standard C8303 (7 A, 125 V) configuration. 4. The flexible cord must be Ty pe RVV, 3-conducto r, 0.75-mm² conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency respons ible for evaluation in the country or region where it will be used. 5. The flexible cord must be Ty pe VCTF, 3-conductor, 0.75-mm² co nductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency respons ible for evaluation in the country or region where it will be used. Requirements for specific countries and regions 91
9R e c y c l i n g Battery When a battery has reached the end of its useful life, do not dispose of the battery in general household waste. Follow the local laws and regulati ons in your area for computer battery disposal. Display WARNING! The backlight contains mercury. Caution must be exercised when removing and handling the backlight to avoid damaging this component and ca using exposure to the mercury. CAUTION: The procedures in t his chapter can result in damage to display components. The only components intended for recycling purposes are the liquid crystal display (LCD) panel and the backlight. When you remove t hese components, handle them care fully. NOTE: Materials Disposal. Th is HP product con tains me rcury in the backlight in the display assembly that might require special handling at end-of-life. Disposal of mercury may be regulated because of environmental consider atio ns. For disposal or recycling informat ion, contact your lo cal authorities, or see the Electronic Indu stries Alliance (EIA ) Web site at http://www.eiai.org . This section provides disassembly instructions for the display assembly. The display assembly must be disassembled to gain access to the backlight (1) and the liquid crysta l di splay (LC D) panel (2) . NOTE: The procedur es provided in this chapter are general disassembly instructions. Specific details, such as sc rew sizes , quantities, and locations, and componen t shapes and sizes, can vary from one computer model to another. 92 Chapter 9 Recycling
Perform the following steps: 1. Remove all screw covers (1) and screws (2) that secure the display bezel to the display assembly. 2. Lift up and out on the left and right inside edges (1) and the top and bottom inside edges (2) of the display bezel until the bezel dise ngages from the display a ssembly. 3. Remove the display bezel 3. Display 93
4. Disconnect all display panel cables (1) from the display inverter and remove the inverter 2. 5. Remove all screws (1) that secure the display panel as sembly to the display enclosure. 6. Remove the displa y pane l assembly (2) from the display enclosure. 7. Turn the display panel assembly upside down. 8. Remove all screws that se cure the display panel frame to the display panel. 9. Use a sharp-edged tool to cut the tape (1) that secures the sides of th e display pa nel to the display panel frame . 94 Chapter 9 Recycling
10. Remove the display panel frame (2) from the display panel. 11. Remove the screws (1) that secure the backlight cover to the display panel. 12. Lift the top edge of the backlight cover (2) and swing it outward. 13. Remove the backlight cover. 14. Turn the display panel right-side up. 15. Remove the backlight cables (1) from the clip (2) in the display panel. 16. Turn the display panel upside down. Display 95
17. Remove the backlight fram e from the display panel. WARNING! The backlight conta ins mercury. Exercise caution when removing and handling the backlight to av oid damaging this c omponent and causing exposure to the merc ury. 18. Remove the backlight from the backlight frame. 19. Disconnect the display cable (1) from the LCD panel. 20. Remove the screws (2) that secure the LCD panel to the display rear panel. 21. Release the LCD panel (3) from the display rear panel. 96 Chapter 9 Recycling
22. Release the tape (4) that secures the LCD panel to the display rear panel. 23. Remove the LCD pane l. 24. Recycle the LCD panel and backlight. Display 97
Index A AC adapter spare part numbers 30 AC adapter, spare p art numbers 24, 25 action keys 8 antenna locations 13 audio, product description 2 audio-in jack connector pinout 87 location 11 audio-out jack connector pinout 87 location 11 B backup and recovery, Wind ows 7 backing up information 80 creating hard drive copy 76 creating recover y discs 81 Disaster Recovery utility 77 HP Recovery Manager 80 Instant Restore utility 78 performing a rec overy 76, 82 restoring to previous date and time 79 system restore points 79 using recovery discs 82 using Roxio BackOnTrack 75 using the hard drive partition 82 Windows Backup and Restore 78 backup and recovery, Wind ows XP backing up information 83 creating a hard d rive copy 84 Disaster Recovery utility 85 Instant Restore utility 86 performing a rec overy 84 base enclosure spare part numbers 26, 27 base enclosure, sp are part numbers 19, 29 battery removal 38 spare part numbers 20, 27, 38 battery bay 12 battery light 10 battery releas e latches 12 boot options 7 4 buttons TouchPad 6 TouchPad on/off 6 C cables, service c onsiderations 33 caps lock light 7 changing the language of Setup Utility 71 chipset, product description 1 components bottom 12 computer, major 15 display 11 display assembly 21 front 8 keys 8 left-side 10 lights 7 pointing device 6 right-side 9 TouchPad 6 wireless antennas 13 computer feet locations 37 spare part number 37 connector pinout audio-in j ack 87 audio-out jack 87 external monitor port 88 headphone 87 microphone 87 monitor port 88 network jack 89 RJ-45 jack 89 Universal Ser ial Bus (USB) port 89 connectors, service considerations 33 D devices, mass storage 23 Diagnostics Menu, Setup Utility 74 Digital Media Slot 9 diskette drive precautions 33 product description 2 display assembly removal 61 spare part numbers 15, 25, 27, 28, 30 , 30, 61 display bezel, spare part numbers 21, 25 display enclosure spare part numbers 29 display enclosure, sp are part numbers 2 2, 25, 26 display hinge caps spare part numbers 27 98 Index
display hinge caps, spare part numbers 22 Display Hinge Ki t, spare part numbers 21, 25 display panel cable, HD spare part numbers 27 display panel cable, spare part numbers 22, 26 display panel, spare part numbers 21 display rubber kit spare part numbers 27 Display Rubber Kit, spare part numbers 22 Display Screw Ki t, spare part numbers 22, 26 display switch 11 drive light 10 drives, preventing damage 33 DVD±RW and CD-RW SuperMulti Combo Drive, spare part numbers 23, 25 E electrostatic discharge 34 Ethernet, product description 2 exiting Setup Utility 73 external media cards, product description 3 external monitor port connector pinout 88 location 10 F fan/heat sink assembly removal 67 spare part numbers 19, 26, 67 feet locations 37 spare part number 37 fn key 8 G graphics, product description 1 grounding equipment and methods 36 guidelines, grounding 3 4 H hard drive precautions 33 product description 2 removal 43 self test 74 spare part numbers 20, 23, 27, 43 hard drive bracket, removal 44 Hard Drive Hardware Kit, spare part number 43 Hard Drive Hardware Kit, spare part numbers 20, 23, 26 hard drive, removal 4 3 hard drive, spare pa rt number 43 hardware, identifying 5 headphone jac k connector pinout 87 location 11 hinge, spare part numbers 21, 25 I internal media cards, product description 3 J jacks audio-in 11 audio-out 11 headphone 11 microphone 11 network 10 RJ-45 10 K keyboard product description 3 removal 52 spare part numbers 16, 26, 27, 28, 29 , 29, 52 keys action 8 fn 8 Windows applications 8 Windows logo 8 L language support 74 lights battery 10 caps lock 7 drive 10 mute 7 power 9 TouchPad 7 webcam 11 wireless 7 M Main Menu, Setup Utility 73 mass storage devices, hard drive 23 memory module product description 1 removal 49 spare part numbers 19, 31, 49 memory test 74 microphone 11 microphone jack connector pinout 87 location 11 miscellaneous parts 24 model name 1 modem, product description 2 monitor port connector pinout 88 location 10 mute light 7 N navigating in Setup Utility 72 network jack connector pinout 89 location 10 O operating system, product description 4 optical drive product description 2 spare part numbers 23, 25 optical drive, external spare part numbers 25 P packing guidelines 35 panels, product descrip tion 1 part number, sequential listing 25 parts, miscellaneous 24 passwords 73 Index 99
plastic parts 32 pointing device componen ts 6 product description 3 ports external monitor 10 monitor 10 product description 3 Universal Se rial Bus (USB) 9, 11 power connector 1 0 power connecto r cable removal 69 spare part numbers 19, 26, 69 power cord requirements for all countries 90 requirements for specific countries and regions 91 set requirements 90 spare part numbers 24, 25 power light 9 power requirements, product description 4 power switch 9 processor C4 state 74 processor, product description 1 product description audio 2 chipset 1 diskette drive 2 Ethernet 2 external medi a cards 3 graphics 1 hard drive 2 internal media car ds 3 keyboard 3 memory module 1 modem 2 operating system 4 optical drive 2 panels 1 pointing device 3 ports 3 power requirements 4 processor s 1 product name 1 security 4 serviceability 4 video 2 wireless 3 product name 1 R recycling battery 92 display 92 removal/replacement preliminaries 32 procedures 37 restoring default settings in Setup Utility 72 RJ-45 jack connector pinout 89 location 10 RTC battery removal 51 spare part numbers 19, 27, 51 Rubber Kit, spare part numbers 19, 26 S Screw Kit, spare part numbers 24, 28 security cable slot 10 Security Menu, Setup Utility 73 security, product description 4 selecting in Setup Utility 72 sequential listin g, part number 25 serial number label, location 14 service considerations 32 service cover removal 40 spare part numbers 20, 26, 27, 30, 31 , 40 serviceability, product description 4 Setup Utility changing the language 71 Diagnostics Menu 74 exiting 73 Main Menu 73 menus 73 navigating 72 restoring default settings 72 Security Menu 73 selecting 72 starting 71 System Configuration Menu 74 using 71 Setup Utility menus 73 SIM, removal 39 speakers location 8 removal 59 spare part numbers 19, 27, 59 starting Setup Utility 71 static-shielding materials 36 system board removal 64 spare part numbers 19, 30, 64 System Configuration Menu, Setup Utility 74 system information 72, 73 T tools required 32 top cover removal 56 spare part numbers 18, 26, 27, 29, 56 TouchPad location 6 TouchPad bu tton 6 TouchPad light 7 TouchPad on/off button 6 transporting guidelines 35 U Universal Serial Bus (USB) port connector pinout 89 location 9, 11 using Setup Utility 71 V vent 9, 10 video decoder, HD spare part numbers 25 video de coder, spar e part numbers 24 video, product descript ion 2 W webcam 11 webcam light 11 100 Index
webcam/microphone module, spare part numbers 22, 25 Windows applications key 8 Windows logo key 8 wireless antenna locations 13 wireless light 7 wireless module, product description 3 WLAN module removal 47 spare part numbers 19, 25, 27, 28, 47 workstation guidelines 35 WWAN module removal 45 spare part numbers 20, 25, 45 Index 101