Nokia 9290 Manual
Nokia 9290 Communicator Information Management and Service Provider Guide
Chapter Section Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Nokia 9290 Communicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 PC connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Nokia 9290 Communicator and data services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Nokia 9290 Communicator and Internet service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Nokia 9290 Communicator and e-mail service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Nokia 9290 Communicator and WAP service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Nokia 9290 Communicator and remote/Over the Air (OT A) configuring . . . . . . . . . . 9 Nokia 9290 Communicator and security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 0 Forum Nokia â community for developers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1 Abbreviation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 Shortcuts for the Nokia 9290 Communicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Setup checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1. INTRODUCTION This guide is intended mainly for the IT and Help Desk personnel of Carriers, Corporations, or Internet Service Providers. The following pages provide information to understand the func- tionality of the Nokia 9290 Communicator and the requirements to set up the data call, e-mail, WWW , and WAP services. This guide can also be used as a general technical specification document for the Nokia 9290 Communicator . Please note that this guide is not a substitute for the Nokia 9290 CommunicatorâÂÂs User Guide. The User Guide contains more detailed information about the use of the Nokia 9290 Communicator and should be referred to when step-by-step user instructions are needed. More Nokia 9290 Communicator product information and end- user support can be found at www .Communicatorworld.net ; developer support can be found at www .forum.nokia.com .
2. NOKIA 9290 COMMUNICA TOR Contents: 2.1 Technical specification 2.2 GSM phone feature list 2.3 Content of the sales package 2.4 Optional Nokia original accessories 2.5 To use the phone
2.1 Technical specification Applications ⢠Cellular mobile phone (handsfree, handset, car kit, and headset use) ⢠Desk application with background image and links ⢠Messaging includes SMS, fax, and e-mail ⢠Internet services include WWW and W AP ⢠Contacts ⢠Calendar ⢠Office includes Document, Sheet, File manager , and Presentation viewer ⢠Extras: Calculator , Clock, Games, Recorder , Unit converter , Imaging (Digital camera connectivity), Video player Note: Additional applications can also be found on the CD-ROM in the sales package. Size ⢠Dimensions: 6.22 x 2.20 x 1.06 in. ⢠Weight: 8.6 oz. Technical data ⢠GSM 1900 ⢠32-bit ARM9-based RISC CPU ⢠Operating system: Symbian OS ⢠Memory card slot ⢠Connectivity: IrDA, Ir-TranP , RS-232 ⢠Low power consumption ⢠Active matrix color display with 4,096 colors ⢠Java⢠support ⢠Supports HSCSD* E-mail protocols ⢠POP3 or IMAP4 (Nokia 9290 Communicator supports IMAP4rev1) ⢠SMTP ⢠MIME ⢠MHTML Supported mail servers* ⢠Cyrus IMAPD Mail Server ⢠HP OpenMail ⢠Lotus Domino Mail R5 ⢠Microsoft Exchange ⢠Netscape Messaging Server ⢠Stalker CommuniGate Pro Mail Server ⢠Sun Internet Mail Server ⢠University of Washington IMAP4 Server ⢠Oracle InterOffice Mail Server ⢠Teamware Office Mail Server ⢠Zmailer * Network dependent Attachments/files supported ⢠View ASCII text, and JPEG or GIF graphics ⢠View and edit Word 95/97/2000 and Excel 95/97/2000 documents ⢠View Microsoft PowerP oint 97/2000 slides ⢠View W ordP erfect 7.0/8.0 and Lotus 1-2-3 for SmartSuite for the Millennium ⢠Winzip supported (unzip) â (third-party application required) ⢠WAV audio files Nokia 9290 PC Suite for Nokia 9290 Communicator ⢠For use in Microsoft Windows 95/98/2000 and Microsoft Windows NT 4.0 environments File conversion support ⢠Symbian OS Word <---> Rich T ext Format, Text (MS-DOS), T ext (Windows ANSI), Word 6.0, Word 95, Word 97, Word 2000 ⢠Symbian OS Sheet <---> Excel 5.0, 95, Excel 97, Excel 2000 Calendar and contacts compatibility ⢠Microsoft Schedule 7.x ⢠Microsoft Outlook 97/98/2000 ⢠Lotus Notes 4.5, 4.6, and 5.0 ⢠Lotus Organizer 97, 5.0, 6.0, and GS/4.0 ⢠SyncML remote synchronization (contacts/calendar) Additional software on CD-ROM in sales package ⢠Many Nokia 9290 Communicator applications ⢠PC software ⢠Nokia 9290 PC Suite for Nokia 9290 Communicator ⢠Multimedia converter ⢠Documentation Battery performance Battery Talk/data/ Standby Standby Charging fax time time time time (phone on) (phone off) High-power up to 10 h up to 230 h up to 400 h 3 h Battery BLL-3 1300 mAh Li-Ion 4 Battery information is provided for comparison purposes. Talk and standby times are estimates and vary based on many factors. For complete battery information for this phone and a list of major factors impacting charge times, please refer to www .nokia.com or the phoneâÂÂs user guide.
2.2 GSM phone feature list Display & keypad ⢠Up to five lines for text and status indicators ⢠Indicators (e.g., incoming messages and call forwarding) ⢠Service provider indicator ⢠Welcome message ⢠Menu help texts after a time out ⢠Last digit and full display clear ⢠Full screen cursor editor ⢠One-touch voice mail button ⢠International access ( ) function ⢠Keyguard ⢠Language dependent keymappings ⢠Special characters under â key while in alpha mode ⢠Changing character case by pressing # key once ⢠Illumination Phone features ⢠Customizable profiles (set up from Nokia 9290 Communicator interface) ⢠Clock ⢠Alarm clock (activated from Nokia 9290 Communicator interface, stop alarm also from phone side) Call management ⢠One-key calling: locations 1 to 9 (1 is always voice mail) ⢠Last number redial ⢠Anykey answer ⢠Automatic redial ⢠Automatic answer (works with headset or car kit only) ⢠Supports emergency calls without SIM ⢠One-touch dialing ⢠Conference calling ⢠Call waiting, call hold ⢠Call/fax/data forward, separate for voice, fax and data ⢠Automatic and manual network selection ⢠Alternate line service ⢠Call transfer ⢠Closed user group ⢠Fixed dialing number ⢠Dual T one Multi Frequency (DTMF) signal transmitting ⢠DTMF control characters (pause, wait) ⢠Calling line identification presentation (CLIP) ⢠Calling line identification restriction (CLIR) ⢠Connected number identification presentation (COLP , COLR) ⢠CLI-based caller groups, a ringing tone, and calling priority ⢠Recent calls list with time stamp (Dialed/Received/Missed calls) Phone book memory ⢠The phone book supports multiple name entries per name ⢠Thousands of memory locations (depending on the Nokia 9290 Communicator memory) ⢠Names with multiple numbers (mobile, home, fax) ⢠Up to 250 numbers on the SIM card (SIM specific) Short Message Service ⢠Mobile Originated (MO), send ⢠Mobile T erminated (MT), receive ⢠Message class 0, 1, 2, 3 supported ⢠Easy to call number in message ⢠Sent message delivery report ⢠Cell Broadcast ⢠Multiple SMS sending ⢠Long messages concatenated with nine messages up to 1,337 characters in one message (concatenated with 30 messages in one message up to 4,590 characters in Nokia 9290 Communicator interface)* * Network dependent 5
Security and cost control ⢠Electronic keyguard (Menu â ) ⢠Security code (when a non-owner SIM is inserted) ⢠Device lock ⢠PIN1, PIN2 ⢠Advice of charge ⢠Call restriction ⢠Last and cumulative call timer Other controls V olume control ⢠Number of volume levels: 1 0 ⢠Separate voice volume level settings for handportable, car handsfree, and headset mode ⢠In-call volume control with the scroll keys P ower control ⢠Ignition switching time-out: 45 seconds ⢠Car kit power off: 12 h ⢠Automatic power save if no network available Tone control ⢠Several ringing tones ⢠Ringing types: ascending ringing, normal ringing, WA V, ring once, silent, priority group(s) only ⢠Keypad tone levels: 4 (from off to 3) ⢠Ringing tone levels: 6 (from silent to 5) ⢠SMS/fax/e-mail/clock alarm/calendar alert tones: standard, silent, WAV (volume level can be set separately for each application tone operated from Nokia 9290 Communicator interface) ⢠Downloadable ringing tones Over the Air SMS/Smart messaging Data calls ⢠Data calls send and receive ⢠Fax calls send and receive ⢠Data speeds up to 14.4 kbps SCSD* ⢠Data speeds up to 43.2 kbps HCSD* System specific features ⢠GSM phase 2 signaling ⢠3V SIM Application Toolkit support ⢠Enhanced full rate (EFR) speech codec ⢠Full rate speech codec ⢠Encryption algorithms: none, A5.1, A5.2 ⢠Discontinuous transmission (DTX) ⢠Cell broadcast (DRX) ⢠USSD (mobile originated and terminated) ⢠SIM Application Toolkit (Class 1.bis) * Network dependent Smart messaging (Over the Air SMS) features ⢠Name and number (business card) sending and receiving ⢠Calendar note sending and receiving (Nokia 9290 Communicator interface) ⢠Ringing tone receiving (Nokia 9290 Communicator interface) ⢠Carrier logo receiving ⢠WAP (operated from Nokia 9290 Communicator interface) ⢠WWW settings (access point), (operated from Nokia 9290 Communicator interface) Infrared features ⢠Name and number receiving (vCard) ⢠Calendar note receiving (vCal) ⢠File transfer between Nokia 9290 Communicators ⢠Digital camera connectivity ⢠Receiving is activated from Nokia 9290 Communicator or phone interface, sending from Nokia 9290 Communicator interface Note 1: Some of the above features are network dependent. Note 2: In the case of local network dependent features or other market specific features (such as languages, ALS), parties shall agree separately in writing if the feature is activated. 2.3 Content of the sales package The Nokia 9290 Communicator sales package contains the following articles (however , the content may vary due to country specific requirements): ⢠Transceiver (Nokia 9290 Communicator) ⢠High-power Battery BLL-3 (1300 mAh Li-Ion) ⢠16 MB MMC Memory Card ⢠Performance Travel Charger ACP-12U ⢠RS-232 Adapter Cable DLR-2L ⢠Folder ⢠User Guide ⢠Getting Started Guide ⢠Third-party application guide ⢠CD-ROM (Nokia 9290 PC Suite, additional Nokia 9290 Communicator software, and documentation) ⢠W arranty card 6
2.4 Optional Nokia original accessories The following optional Nokia original accessories are available for the Nokia 9290 Communicator: ⢠Advanced Desktop Stand DCH-1 0 ⢠High-power Battery BLL-3 ⢠Performance Travel Charger ACP-12U ⢠Advanced HF Car Kit CARK-1 09 ⢠Mobile Charger LCH-9 ⢠Headset HDC-8L ⢠Carry Case (vertical and horizontal styles) ⢠Memory Card (64 MB) ⢠RS-232 Adapter Cable DLR-2L 2.5 To use the phone To be able to send and receive calls and messages: ⢠The phone must be turned on ⢠A valid SIM card must be inserted ⢠You must be located in the service area of the wireless (GSM) network ⢠The local carrier services must be available and activated to support services like data call, e-mail, fax, WWW , and W AP 7 INTERNET ⢠You can browse the WWW and use WAP services ⢠You can quickly set up Internet and W AP access points MESSAGING ⢠You can send and receive faxes, e-mail, and short messages, as well as view e-mail attachments TELEPHONE ⢠You can make and answer voice calls ⢠You can talk in handsfree mode using the high- quality speakerphone DESK ⢠You can create, edit, and manage links to other applications or third-party software ⢠You can also customize the background image of your Nokia 9290 Communicator CONTACTS ⢠You can manage all your contact data in the same place ⢠You can use the telephone, short messages, fax, and e-mail applications with this information CALENDAR ⢠You can check appointments and special events, list things to do, and set alarms for calendar entries OFFICE ⢠You can view and edit Document and Sheet files, view presentations, as well as organize your files in File manager EXTRAS ⢠You can access the Clock, Unit converter , Calculator , Imaging, Voice recorder, Video player and Control panel functions, as well as add-on applications HELP ⢠You can access the help function from any application MENU ⢠Opens a set of options depending on the application you are in ARROW KEYS ⢠You can scroll up and down, left, right, and diagonally
3. APPLICA TIONS Contents: 3.1 Desk 3.2 Tel 3.3 Messaging 3.3.1 SMS 3.3.2 Mail 3.3.3 Fax 3.4 Internet 3.4.1 WWW 3.4.2 WAP 3.5 Contacts 3.6 Calendar 3.7 Office 3.8 Extras 3.8.1 Control panel 3.9 Other applications 3.9.1 Log 3.9.2 Receive via IR 3.9.3 SyncML - remote synchronization
9 3.1 Desk The Desk application group is used for managing and using various links to your favorite applications or third-party software. Y ou create these links in the relevant applications. Also, quick notes can be written in this application. The Desk application is customizable by the user: ⢠Background image is changeable ⢠Reminder notes can be created quickly ⢠Shortcuts/links can be created to: ⢠Applications ⢠Messages ⢠WWW pages and WAP bookmarks ⢠Documents, Sheets, Notes 3.2 Tel Telephone is the application for call management and adjusting the telephone settings. The main telephone features are listed below . The full GSM telephone feature list can be seen in chapter 2.2. ⢠Make and receive voice calls ⢠Multiple search criteria for the telephone directory ⢠Handsfree option ⢠Sending sequences of dial tones (D TMF) during the active call ⢠Maintain list of DTMFs for quick access ⢠Maintaining phoneâ s speed dial list ⢠Monitoring call costs ⢠Adjusting the phone volume level 3.3 Messaging The Messaging application is a central place for Fax, SMS, and Mail applications. Y ou can write, edit, and send mail, short messages, and faxes in their corresponding editors. ⢠Inbox folder for received messages and faxes ⢠Sent messages folder for sent messages ⢠Drafts folder for messages not yet sent or ready ⢠Outbox folder for messages that are selected to be sent but are not yet sent ⢠New messages note appears in the screen when new fax, e-mail, or short messages arrive ⢠Contact cards can be created from messaging editors/ viewers address fields ⢠Recipient/sender information is compared to contacts database information (entry verifying) 3.3.1 SMS User can write and receive short text messages (SMS). The following SMS features are supported: ⢠Unclassified short messages ⢠Class 0, 1, 2, and 3 short messages ⢠Concatenated short messages (e.g., messages over 160 characters) ⢠Received class 2 short messages (SIM specific) are stored both in the SIM and in the Inbox ⢠Multiple recipients ⢠Send options: Delivery , Date (in scheduled sending), Time (in scheduled sending), Delivery report, Validity period, Reply path request, Service center , Message conversion ⢠Unicode (character) support 3.3.2 Mail User can send and receive e-mail. Mail addressed to you is not automatically received by your Nokia 9290 Communicator , but by your remote mailbox. To read your mail, you must first connect to the remote mailbox and then select the messages you wish to retrieve. The connection is established via a data call. The following features are supported: ⢠Multiple mailboxes, new mailboxes can be added ⢠Carrier or service provider can add new remote mailboxes by smart messages ⢠Disconnected (= offline) mode ⢠Read e-mail attachments: Windows Word, Excel, and P owerPoint. You can view many other file types too, like Lotus files. More file viewers are provided on the CD-ROM supplied in the sales package. ⢠Mail editor with font formatting, alignment adjusting, object inserting, spell checking (installable from CD-ROM, English only) and bulleting features ⢠Sending mail attachments ⢠Opening attachments from mail viewer to appropriate application ⢠Send as mail (attachment) functionality from other applications (menu command) ⢠Send options: Priority , Message type, Copy to self, Request read receipt, Mail account, Send message ⢠Multiple recipients. Recipient fields: To, Cc, Bcc ⢠Special strings (phone numbers, URLs, etc.) are recognized in Mail viewer and can be used for making a call or launching Web application ⢠PCMail for PC synchronization
10 3.3.3 Fax User can read, write, and send fax messages. The Fax editor allows user to write formatted text with embedded objects such as spreadsheet objects. User can also use another editor for writing fax messages. The Fax viewer is used for viewing received faxes (fax images). ⢠Fax ECM (Error Correction Mode) provides automatic resending of pages in case of error ⢠Normal Fax polling (user makes fax call, other end sends fax in the same call to the user â network dependent feature) ⢠Class 2 and 2.0, Group 3 ⢠Transmission speed up to 14.4 kbps ⢠Receive and send resolution ⢠standard 60 x 60 dpi ⢠fine 100 x 1 00 dpi ⢠Fax restriction and fax forwarding ⢠Menu commands for sending written fax also as SMS, mail, or via IR ⢠Cover page templates for easy fax writing and for corporate usage ⢠Fax is a network service 3.4 Internet The Internet application provides access to Internet and value-added services â with Login script and Callback supported. The Main view contains WWW and WAP browser application icons as default. 3.4.1 WWW The Nokia 9290 Communicator has a full-featured W eb browser including: ⢠HTML 3.2 support (including frames support) ⢠HTTP 1.1 ⢠Color WWW pages support ⢠Pointer ⢠Add link bookmark and frame bookmark ⢠Full screen mode ⢠Font style and size can be changed (which show Web page) ⢠Secure W eb browsing (HTTPS) supported over SSLv3 and TLSv1 ⢠WWW browser plug-in support ⢠Caching of Web pages and offline browsing ⢠History lists ⢠Bookmarks ⢠Reload ⢠Find 3.4.2 WAP There are two views in WAP browser: the Bookmarks view and the Card view . The Card view consists of a rendered card and options list. Bookmark view consists of a hierarchical list of saved bookmarks. The main features: ⢠WAP 1.1 ⢠Displaying the encoded WML from the WBXML ⢠Displaying online WBMP images with the WML ⢠Follow the state modals defined in the WML for navigation ⢠Supports WMLScript ⢠Supports color images ⢠Use of the WAP stack for optimal Over the Air (O TA) bandwidth usage ⢠Number of bookmarks supported: 1 00 ⢠Tables supported ⢠Find 3.5 Contacts Use Contacts for creating, editing, and managing all contact information, such as phone numbers and addresses. The main contacts database is in the Nokia 9290 Communicatorâ s memory . Other applications (such as telephone, short messages, fax, and e-mail) use contact information from this application. You can also store contacts in separate databases on an attached memory card. ⢠Several phone numbers per contact/entry supported ⢠Three address fields (Preferred, Business, Private) ⢠Phone call, SMS, or e-mail can be created/sent directly from contact card ⢠Group cards to send short messages, faxes, or e-mails to a large number of people ⢠SIM and Memory Card contacts can be viewed and edited through this application ⢠One-touch dialing, individual ringing tones, and contact images can be assigned to a contact card ⢠General and individual logs ⢠Contacts database can be exported to PC and imported from PC ⢠By using Sync-button on the deskstand, database can be synchronized with the most common PC contacts databases, such as Microsoft Schedule , Microsoft Outlook, Lotus Notes, Lotus Organizer , etc. (More third-party converters can be added later) ⢠vCard compatible
11 Contacts compatibility: ⢠Microsoft Schedule 7.x ⢠Microsoft Outlook 97/98/2000 ⢠Lotus Notes 4.5, 4.6, 5.0 ⢠Lotus Organizer 97, 5.0, 6.0, GS/4.0 ⢠SyncML remote synchronization 3.6 Calendar The Calendar application is used for organizing time usage by storing and viewing information about events and tasks. ⢠Calendar has the following views: Month, Week, Day , Weekly time schedule, Y ear schedule, Anniversaries, and T ask lists ⢠Multiple task lists ⢠Task lists with alarms and priorities ⢠Possibility to have several calendars (e.g., for private and business usage) ⢠Colors and icons can be used to separate different types of calendar events ⢠Calendar events can be sent and received as smart messages ⢠National holidays and other calendar events can be received from WWW as normal calendar files ⢠Calendar can be exported to a compatible PC and imported from a compatible PC ⢠By using Sync-button on the deskstand, calendar data can be synchronized with the most common PC calendars, such as Microsoft Outlook, Schedule , Lotus Notes and Lotus Organizer ⢠Private and public option in calendar event: for example, only public events can be synchronized with PC Calendar compatibility: ⢠Microsoft Schedule 7.x ⢠Microsoft Outlook 97/98/2000 ⢠Lotus Notes 4.5, 4.6, 5.0 ⢠Lotus Organizer 97, 5.0, 6.0, GS/4.0 ⢠SyncML remote synchronization 3.7 Office Office application group contains the following applications: ⢠Document for viewing, creating, and editing documents â Microsoft Word compatible ⢠Spreadsheet for viewing, creating, and editing spread- sheets â Microsoft Excel compatible ⢠Presentation viewer â Microsoft P owerP oint compatible ⢠File Manager for file management 3.8 Extras Extras is an application group for several types of applications, for instance: Clock, Calculator , Games, Imaging application, Control panel, Recorder , Video player , and Unit converter . Also, additional applications can be installed here by using the Nokia 9290 PC Suite for Nokia 9290 Communicator . 3.8.1 Control panel The Control panel application manages all the settings that are not related to one single application. There is also one operational feature in Control panel Main view , namely âÂÂLock system.â Control panel main view contains several icons for different setting categories. Opening them will display a dialog or another view . The settings are: Display Contrast, brightness, color , and screen blanker settings Date & time Present time setting, clock, and agenda alarm snooze times settings Regional settings Time, date, number , and currency formats Internet access The user can edit, make new , and delete Internet connections, which are used in different applications.
12 Profiles Enables the user to control the audio-visual function- ality and accessibility of the device. Each profile is a group of setting values that can be activated at once by activating the profile. One of the profiles is always active. Default profiles are Normal, Silent, Flight, Outdoor , Meeting, Pager , and Car , but the user may add, delete, and modify them as s/he wishes. Security The following settings can be modified: ⢠PIN code request ⢠Autolock period ⢠SIM change security ⢠PIN code ⢠PIN2 code ⢠Lock code ⢠Restriction password Certificate manager Managing of cryptographic keys. For example, SSLcertificate. Install/remove add-on applications It opens a Main view of the Applications Installer . Default folder User can specify the folder that all applications should use as the default folder in the âÂÂSave asâ command. Memory Shows detailed view of device and memory card usage by file type. Accessories Settings for car kit and headset accessories. About product Detailed information about the Nokia 9290 Communicator . Regional settings Date, time, number , and currency preferences. 3.9 Other applications 3.9.1 Log Log application shows communications from and to the device. Application menus (Menu â Tools) have a command for easy access to log application. 3.9.2 Receive via IR Infrared (IR) receiving is possible to activate through application menus or by keyboard shortcuts at any time. Received files or messages end up in the Messaging Inbox. Infrared in general has the following features: ⢠Support IrDA ⢠Support for IrTranP ⢠IrObex 1.1 ⢠Transmission speed up to 1 15 kbps 3.9.3 SyncML â remote synchronization The Nokia 9290 Communicator supports the SyncML syn- chronization of contacts, calendar , and task lists over the GSM data call. Nokia 9290 Communicator will work with SyncML-enabled network applications and services. The Nokia 9290 Communicator Remote synchronization application is supplied on the CD-ROM in the Nokia 9290 Communicator sales package. The Nokia 9290 Communicator works with SyncML-enabled synchronization servers that support PIM data (contacts, calendar , task lists). There will be various vendors bringing SyncML-enabled synchronization servers both for carriers and Internet service providers (synchronizing with Internet calendars) and for the corporate market (synchronizing with Lotus Domino or Microsoft Exchange). The list of products that have passed the conformance and interoperability tests of the SyncML initiative can be found at the SyncML initia- tiveâÂÂs Web site, www .syncml.org . In addition to the contacts, calendar , and task lists, there is a possibility for independent software vendors to build corporate solutions or vertical applications (inventory data synchronization, sales data synchronization, etc.) based on SyncML technology on top of the Symbian operating system in the Nokia 9290 Communicator .
4. PC CONNECTIVITY Contents: 4.1 Nokia 9290 PC Suite for Nokia 9290 Communicator 4.2 Upgrade software 4.3 Multimedia converter 4.4 Nokia 9290 Administrator Suite
4.1 Nokia 9290 PC Suite for Nokia 9290 Communicator Y ou can connect your Nokia 9290 Communicator to a com- patible P C o r laptop using the Nokia 9290 PC Suite for Nokia 9290 Communicator program supplied on the CD-ROM in the Nokia 9290 Communicator sales package. Nokia 9290 P C Suite for Nokia 9290 Communicator works with Windows 95/98/2000 and NT 4.0. The Nokia 9290 PC Suite features are: ⢠File management â Provides access to the Nokia 9290 Communicator file management as well as the userâ s own PC file management to move, copy , rename, and delete files and folders on and between your Nokia 9290 Communicator and your PC. ⢠Task scheduler â Enables the user to specify regular tasks and then automatically manages these for the user . Y ou can synchronize applications data like contacts or e-mails between your Nokia 9290 Communicator and your PC. ⢠Backup/restore â (Archive Manager) enables an easy way to view backed-up files and restore different archived versions. ⢠Control panel â Provides access to all Nokia 9290 PC Suite settings. ⢠Installing applications ⢠Offline mode â Y ou can also use Nokia 9290 PC Suite when it is not connected to your Nokia 9290 Communicator (offline mode). When you connect the two devices the next time, the changed information is updated from your PC to your Nokia 9290 Commu- nicator and vice versa. ⢠Plug-ins ⢠PC upgrade software (section 4.2. below) ⢠Nokia 9290 Administrator Suite (section 4.4 below) ⢠Other additional plug-ins 4.2 Upgrade software The upgrade software is a PC connectivity plug-in. Therefore, you first have to install the Nokia 9290 PC Suite for Nokia 9290 Communicator before installing this program. This upgrade program enables you to move your contact data (phone book), and calendar from the Nokia 51 00, 6 100, 7 100, 8200, 8800 series GSM phones and the Nokia 9 1 10 Communicator to the Nokia 9290 Communicator . The upgrade software is supplied on the CD-ROM of the Nokia 9290 Communicator sales package. 4.3 Multimedia converter With Multimedia converter you can convert common video file formats to NIM format playable on the Nokia 9290 Communicator . When converting a video file, the size of the converted file is usually much smaller than the size of the original file. Y ou can also convert common audio file formats to WAV format and optimize existing WAV format sound files for use on the Nokia 9290 Communicator . Y ou can use converted WA V files as ringing tones, for example. Multimedia converter runs on the 32-bit Microsoft Windows operating system (95, 98, Me, NT4, and 2000). It is included on the CD-ROM of the sales package. Y ou can use the Nokia 9290 PC Suite for Nokia 9290 Communicator to copy converted files to your Nokia 9290 Communicator via a serial cable or an infrared (IR) connec- tion. Y ou can also store video clips directly to a memory card, if you have an appropriate peripheral installed in your com- puter . NIM files can also be stored on a Web server and referred from an HTML page. This enables users to down- load NIM files into the Nokia 9290 Communicator . Multimedia converter supports most files that you can play in Windows Media Player . The exact set of supported files depends on the version of Media Player installed in your system and on the installed audio and video codecs. Typically , Multimedia converter is able to support most AVI, W AV , MPG, and MP3 files. Note: Y ou can play a NIM file on your PC using Multimedia converter only . 4.4 Nokia 9290 Administrator Suite Nokia 9290 Administrator Suite is an additional PC software that is targeted to retailers and corporate IT personnel. It features Nokia 9290 Communicator setting, file, and appli- cation delivery to the Nokia 9290 Communicator . The Nokia 9290 Administrator Suite is supplied on the CD-ROM in the Nokia 9290 Communicator sales package. It is possible to transfer the configurations to the Nokia 9290 Communicator either by connecting the Nokia 9290 Communicator to the PC where the Nokia 9290 Administrator Suite is locally or remotely . In the user interface of the Nokia 9290 Administrator Suite it is possible to create a whole selection of different settings, applications, etc. and transfer that set to one or several Nokia 9290 Communicators. This makes it possible to easily administer several Nokia 9290 Communicators from one service point. The following settings can be configured: ⢠IAP settings ⢠E-mail settings ⢠WAP settings ⢠SMS settings It is also possible to transfer/install: ⢠WWW bookmarks ⢠WAP bookmarks ⢠Voice and fax mailbox numbers ⢠Files ⢠Applications/software In short, the Nokia 9290 Administrator Suite will help company administrators to offer a standard Nokia 9290 Communicator software and setting package to their users. 14
5. NOKIA 9290 COMMUNICA T OR AND DA T A SERVICES Contents: 5.1 Introduction 5.2 Data call and high-speed data options
5.1 Introduction Before you can start to use the Nokia 9290 Communicator data features efficiently , you have to check the following information from your GSM carrier: ⢠The cellular network that you use must support data calls ⢠Data service must be activated for your SIM card ⢠Before you can use HSCSD data, check with your carrier to see whether it is supported 5.2 Data call and high-speed data options Data call options can be handled in Internet settings. Under Advanced settings; Connection type, Remote modem type and other data call related information could be found and edited. Connection type gives two alternatives for the connection type. The default for every IAP (Internet Access Point) is âÂÂNormal,â which stands for normal single time slot GSM data call. The connection speed can be either 9600 or 14400 bps, and in addition for analog calls autobauding is the third speed option. âÂÂHigh speedâ selects the High Speed Circuit Switched Data (HSCSD) call. Higher transfer speeds are achieved by reserving multiple GSM time slots for single user . Note: The 14400 bps speed for normal GSM data call and HSCSD services are not basic GSM data services. These services may not be available in all networks in all areas , and they may require a separate subscription. If the network does not support the call type, or it has not been enabled in the userâ s subscription, the data call may fail. Even the basic data call services may need to be subscribed to separately . Remote modem type defines the connection method to be used. There are three alternatives available: Analog (for normal modems), ISDN V.1 10, and ISDN V.120. The GSM network and the remote access server or dial-in modem pool must support the selected connection method; other- wise, the connection attempt will fail. Note: Analog (normal modem) connections are usually supported in all networks. The connection time (before the data call is established) is about 40 seconds for analog connections and 15 seconds for ISDN connections 1 . Maximum data speeds are 28800 bps for analog, 38400 bps downstream for V.1 1 0 and 43200 bps downstream with V.120. In addition, the data flow may be smoother when using ISDN connections. These restrictions are caused by the GSM network, and are not inherent to the Nokia 9290 Communicator . Max. connection speed is for determining the maximum connection speed. The GSM network may change the current connection speed at its direction â for example, when the network becomes congested. Note: All HSCSD connections are always made with 14400 bps per timeslot. This speed is almost always available in the areas where network coverage is good and the network supports HSCSD. If the network signal quality gets weaker , the speed is automatically do wngraded to 9600 bps per timeslot by the GSM network. The network can also decrease the number of time slots allocated for a user if network congestion occurs. These actions may cause fluctuations in the data rate, and may cause the total data rate to be smaller than the requested data rate. 1 These times are rough estimates and depend on the network coverage, on the Internet service provider , and other variables. 16 When HSCSD connections are used, the user may control how many timeslots are used for the connection. Some GSM carriers may charge on slot amount usage basis; some other GSM carriers may implement a fixed charging model for HSCSD calls. Please contact your network carrier for HSCSD coverage and charging details. Connection type Remote modem type 1 timeslot 2 timeslots 3 timeslots Normal data call Analog Autobauding, Not available Not available 9600 or 14400 ISDN V.1 10 9600 or 14400 Not available Not available ISDN V.120 9600 or 14400 Not available Not available High-speed data call Analog 9600 or 14400 19200 or 28800 Not available ISDN V.1 10 9600 or 14400 19200 or 28800 28800 or 38400 ISDN V.120 9600 or 14400 19200 or 28800 28800 or 43200 Available connection speeds are:
6. NOKIA 9290 COMMUNICA T OR AND INTERNET SERVICE Contents: 6.1 Introduction 6.2 Nokia 9290 Communicator and Internet features 6.3 Creating Internet connections 6.4 Connection details 6.5 Advanced settings 6.5.1 Setting proxies 6.5.2 Modifying data call settings 6.5.3 Taking callback into use 6.5.4 Other settings 6.5.5 Setting script options 6.5.6 Setting server address options 6.6 Editing Internet access 6.7 Tested Nokia 9290 Communicator compatible PPP access servers 6.8 Default parameters and settings
6.1 Introduction This chapter describes how to configure Internet settings manually to the Nokia 9290 Communicator to be able to access the Internet. Information concerning the correct settings must be obtained from the Internet service provider (ISP). The service provider may be able to configure the access point for you via a special SMS message or a WWW page, which sets all the necessary Internet access settings. Please contact your Internet service provider (ISP) for details. For more information about using the Internet application, please refer to the User Guide of the Nokia 9290 Communicator . 6.2 Nokia 9290 Communicator and Internet features The Nokia 9290 Communicator supports the following basic Internet features: ⢠Normal single-slot GSM data calls using either 9600 bps or 14400 bps ⢠Support for analog modem connections and ISDN V.1 1 0 and ISDN V.120 rate adaption protocols ⢠Point to P oint Protocol as the data link level protocol, RFC 166 1 ⢠PPP link level authentication using the Password Authentication Protocol (PAP) or Challenge Authentication Protocol (CHAP), RFC 1334 ⢠PPP link level compression using Stac LZS (modes 4 and 3), MPPC, and Predictor compression methods, RFC 1974 ⢠PPP callback using the Microsoft callback protocol (client supplied number , server supplied number) and PPP callback type 0 as specified in RFC 1570 ⢠Internet Protocol Control Protocol (IPCP) extensions for Domain Name Service (DNS) ⢠Scripting language for automating login procedures, compatible with previous Symbian OS devices (such as PsionâÂÂs Series 5 PDAs) ⢠Van Jacobson TCP/IP header compression, RFC 1 144 ⢠Secure Sockets Layer (SSL) version 3 and T ransport Layer Security (TLS) version 1 protocols To obtain access to the Internet: ⢠The cellular network (GSM 1900) you use must support data calls ⢠The data service (also the High-speed (HSCSD) service if used) must be activated for your SIM card ⢠You must have obtained an Internet Access Point (IAP) from an Internet service provider ⢠You must have entered the proper Internet settings 6.3 Creating Internet connections Obligatory settings for Internet connection are (information from Internet service provider): ⢠Phone number where to call ⢠Username ⢠Password ⢠Data call options (especially when HSCSD data is used) To set up new Internet access: 1. Open Internet startup from Desk or from under Extras. 2. Select Internet access and press Open. 3. T o create an Internet connection, press New . If you want to modify an existing Internet Access P oint, open Internet access from Control panel in the Extras application. 6.4 Connection details 1. Open Control panel from Extras. 2. Select Internet access and press Open. 3. T o view and edit existing Internet connections, select the IAP you want by pressing Change. T o create a new Internet Access Point, press New . 4. Create a Connection name that you can recognize easily (e.g., name of the ISP). 5. Type in the phone number of your Internet account. This is the phone number of the dial-in line (also called the modem pool or PPP servers) of the ISP . Y our ISP may have several different phone numbers for different modems. 6. Set Password prompt to Y es if you want to type in your password every time you log in. Select No to save your password in your Nokia 9290 Communicator and auto- mate the login procedure. If you are using one-time passwords (such as RSA SecurID or OTP), select Y es. 7. T ype in the Username for your Internet account. 8. T ype in the Password for your Internet account. Then confirm the password by retyping it in the Confirm password field. Note that the characters in your password are replaced with symbols so that no one can see them accidentally . Note also that usernames and passwords are usually case-sensitive (capitalization of letters matters). The username and password are used for PPP (Point to P oint Protocol) authentication and supplied to you by your Internet service provider . Some IAPs do not require the username and password; some IAPs may only require the phone number and the connection name. 18
6.5 Advanced settings To define advanced settings of the connection, press Advanced settings. A dialog with four pages opens. 6.5.1 Setting proxies Y ou may wish to use a proxy to speed up access to the Internet. Note also that some ISPs require the use of WWW proxies; contact your ISP to determine the proxy details. Y ou may also need a proxy server when you have an Internet connection for your companyâ s intranet, and as a result are unable to retrieve W eb pages from the WWW . In this situa- tion you may need to set up a proxy server to retrieve W eb pages outside your companyâ s intranet. A proxy is a server at the interface between your Nokia 9290 Communicator and the remote (target) WWW server that offers the W eb pages. Proxies usually cache popular documents so that they do not need to be reloaded from the remote server every time they are accessed. After you get the connections working, you may want to test the connection speed with and without proxies to find out whether they offer any increase in speed. 1. Select the Protocol for your connection. (HTTP is for normal WWW connections and HTTPS is for SSL-secured WWW connections. Usually , but not always, the proxy information is the same for both protocols.) 2. Set Use proxy server into Yes or No according to your setting requirements. 3. T ype in the P ort number . This is often 8000, 8080, or 80, but can vary by proxy server . 4. T ype in the address of the Proxy server (either the domain name or the IP address). 5. T ype domains that should not be accessed through the proxy server in the No proxy for field. Separate each domain with a semicolon (;). For example, if you want to use proxies for all pages other than those that reside in your companyâ s intranet, write your companyâ s domain name (e.g., yourcompany .com) in this field. If your com- pany intranet requires the use of proxy servers, contact your support person for details. Note: Settings 3, 4, and 5 are available only when proxy servers are used. 6.5.2 Modifying data call settings 1. T o activate the Data call tab, press the Menu key . 2. Select the Connection type. Options are Normal and High speed. Note: T o be able to use High speed, the network service provider has to support this feature, and, if necessary , to activate it for your SIM card. When using High speed, extra charges may apply , even for received data calls within your home network. Check with your network service pro vider for details on their pricing. 3. Select the Remote modem type. The default is Analog, but your service provider may also have ISDN connections available. This setting may depend on both your GSM network carrier and ISP , because some GSM networks do not support certain types of ISDN connections. For details, contact your ISP and network provider . ISDN connec- tions are preferable to analog connections, because they offer considerably faster data call establishment (often about twenty seconds faster than with analog connections), and offer higher data transfer speeds as the connection is fully digital from end to end. On the other hand, if you have problems establishing a data call (for example, when roaming outside your home net- work), using analog connections may help you to estab- lish a connection. 4. Set the Maximum connection speed. When your Connec- tion type is Normal, only autobauding, 9600, and 14400 are available. Different, higher connection speeds are available with different combinations of High speed settings. Higher data rates may cost more, depending on the network service provider . The speed indicated here is the maximum speed that will be used. The true data transfer speed depends on congestion in the Internet, the type of data you are downloading, whether you are run- ning other applications on the Nokia 9290 Communicator , on the congestion of the mobile phone network, and on your location in the mobile phone network. In poor reception areas, the network may choose to use a sig- nificantly lower transmission speed. 5. T ype in the Modem initialization string, if needed, to control the Nokia 9290 Communicator using modem A T commands. Enter characters specified by your network service provider or ISP; otherwise, leave this field empty . The modem initialization string specified here will override all other data call settings. The initialization string may be required if the normal settings are not sufficient for a particularly complex network/IAP configuration. For more details, see also Chapter 5 â Nokia 9290 Commu- nicator and Data Services. 19
6.5.3 Taking callback into use This option allows a server to call you back once you have made the initial call, which means in most countries that a connection is established without your having to pay for the call. Contact your ISP to find out whether this service is available and to subscribe to this service. If you are roaming outside your home network or use high-speed data calls, you may still have to pay for part of the call. Note: Most public ISPs do not support callback. Most common callback users are companies and other private dial-up systems that require increased security . 1. T o activate the Callback tab , press the Menu key . 2. Set Use callback to Y es if you have a service that dials back to your phone when you establish an Internet connec- tion. Callback works as follows: Y ou first dial into the IAP and request callback. The data call is then closed. Within a minute, the IAP has to call back to your Nokia 9290 Communicator . 3. Select the Callback type. Y ou have the option of choosing between IETF PPP callback protocol, which calls back to a number stored on the callback server , and two different modes of Microsoft callback protocol, one of which uses a number stored on the server , and one which uses a client-supplied phone number . 4. If you selected Use number below , type in your Callback number . This number is usually the data call phone number (not the voice number) of your Nokia 9290 Communicator . This is filled in when using Microsoft cal lba ck protocol in a mode where the client specifies the number to call back. The Callback call from the remote server must use the same data call settings as the callback-requesting call. The network has to support the call type in both directions (to and from the Nokia 9290 Communicator). You may need to ask your ISP to configure the callback server accordingly , and check with your network provider as to whether the GSM network supports this functionality . 6.5.4 Other settings 1. To activate the Other tab , press the Menu key . 2. Set Allow plain-text login to No if you donâÂÂt want to send your password as plain text without encryption. Note that this option only affects PPP connections, and some ISPs require that this setting is Y es. Check with your ISP: If your ISP supports CHAP or MS-CHAP , set this to No; if they only support P AP , set this to Y es. 3. Set Use PPP compression to Yes to enable compression. When set to Y es, this option speeds up the data transfer (especially when downloading text and other compressible information) if it is supported by the remote PPP server . If you have problems establishing a connection, try setting this to No. 6.5.5 Setting script options If you need to define script options for your Internet con- nections, move to the Other page of the Advanced settings dialog, then press Script options. A script can automate the connection between the Nokia 9290 Communicator and the server . Note: Scripts are not usually required when you establish a connection. T o find out whether you need a script, contact your ISP . Usually a script is required if the login procedures do not use standard PPP authentication systems (P AP , CHAP , or MS-CHAP). 1. Press Script options to open the Script options dialog. 2. Set Use login script to Yes in case your Internet service provider requires a login script, or if you want to automate your login with a script yourself. 3. Set Display terminal window to Yes if you want to be able to see the execution of the script or to interact with the terminal server during login. Note that this setting is only available when Use login script is set to Y es. 4. T o view and modify the script, press Edit script. 5. T ype in the script. This information is provided by your Internet provider . Press Import script to import script from a file. The scripting syntax is available from Forum Nokia and has to be imported in Unicode format. 6. Press Done to finish. 7. Press Done to close script options. 20
6.5.6 Setting server address options Note: Usually you do not have to alter A ddress options. Most ISPs support automatic configuration of IP and DNS addresses. 1. Press Address options to open the server address options dialog. 2. In the Address options dialog, you can set the addresses of your Internet services. IP addresses are unique strings of numbers that point to computers on the network. Set Auto retrieve IP address to Y es if you want to obtain the IP addresses automatically from the server (this is also called the dynamic IP). To type in the IP addresses on the fields below , select No. T ype in your IP address if Auto retrieve IP address is set to No. In this case, your ISP will provide you with a fixed IP address. 3. If you cannot auto retrieve DNS addresses automatically , set Auto retrieve DNS address to No, and type in the Primary DNS address and the Secondary DNS address if necessary . DNS means âÂÂdomain name serverâ â that is, a server that translates domain names (foo.bar .com) into IP addresses (of the type 000.000.000.000). 4. Press Done to close the Address options dialog. 5. Press Done to close the Advanced settings dialog. 6. Press Done to close the Connection details dialog. Note: New connection is set as Preferred connection by default. T o select a different Preferred connection, press Change. A list of your Internet connections opens. 6.6 Editing Internet access To edit some additional settings of already configured Internet access points, press the Menu key and open the Control panel under T ools (or open it from Extras). Open Internet access. In addition to the settings discussed above, you can also edit the following settings: ⢠Preferred connection: If you have configured several Internet access points, select which one is the preferred one when connecting to the Internet. ⢠If idle, stay online: The connection to the Internet will automatically close after the inactivity period defined here. The options are For 2 minutes/For 5 minutes/ For 1 0 minutes/For 60 minutes. ⢠Ask before connecting: To monitor the connection process, set this setting to Y es. This way you can always see when a connection is established as the connection dialog opens when you use the W eb browser . If you are using several different IAPs (for example, one for company intranet and one for public WWW access, or one for normal and one for high- speed data calls), it is recommended to set this to Y es so that you can always be sure to which IAP the connection will be made. Press Done to close the Connection details dialog. 6.7 Tested Nokia 9290 Communicator compatible PPP access servers This section contains a list of commonly used PPP dial-in access servers, which have been compatibility tested with the Nokia 9290 Communicator . Another type of PPP server may also work, assuming the server has been configured with generally used PPP settings, such as: ⢠The PPP server is capable of establishing data calls using the PSTN/ISDN V.1 10/ISDN V.120 method ⢠The server is able to handle a maximum transfer unit (MTU) of at least 1500 octets ⢠Login script authentication with terminal server or PAP/CHAP authentication with PPP server ⢠Van Jacobson TCP/IP header compression on/off ⢠Dynamically/manually set IP and DNS addresses ⢠PPP compression provided by Compression Control Protocol on/off ⢠IP packet routing gateway information is set by the PPP server The configuration options listed here may differ for your local Internet access point. Please contact your local ISP or corporate information management to get more information about used parameters for your Internet Access P oint. 21
Compatibility tested PPP servers with the Nokia 9290 Communicator: Cisco AS5300 Cisco AS5200 Shiva Access Switch Shiva LanRover E Microsoft NT RAS 4.0 Ericsson Tigris AXC 623 Ascend Max 4004 Lucent P ortMaster 3 Nortel/Bay Networks Versalar 8000 Morning Star PPPD Various Linux/Unix based PPP daemons conforming RFC 166 1 6.8 Default parameters and settings ⢠Async Control Character Map (ACCM) 0x00000000 ⢠Dynamic protocol timeout for LCP , IPCP , CCP , P AP , and CHAP 3 seconds ⢠Maximum Receive Unit (MRU) 1500 ⢠Magic number negotiation is on ⢠Address and Control field Compression is on ⢠Maximum configure request restart 1 0 ⢠Maximum configure Naks before failure 5 ⢠Link quality report interval 1 0 seconds ⢠Compression method negotiation order (PPP compression on by default): ⢠Stac LZS mode 3 ⢠Stac LZS mode 4 ⢠Microsoft PPC ⢠Predictor 1 ⢠PPP callback is off ⢠TCP/IP-header Van Jacobson compression on ⢠TCP maximum segment size (MSS) 536 bytes ⢠Maximum time-to-live (TTL) 64 ⢠Default PPP idle timeout is 2 minutes ⢠Show connection dialog is off ⢠Proxy servers are off by default ⢠Default data call parameters are normal analog data- calls, autobauding, and no AT commands ⢠Plain text login is allowed by default ⢠Login scripts are not used by default ⢠IP addresses and DNS addresses are requested dynami- cally from server by default ⢠For SSL and TLS, a collection of well-known certification authoritiesâ root certificates has been installed and marked as trusted 22
7. NOKIA 9290 COMMUNICA T OR AND E-MAIL SERVICE Contents: 7.1 Introduction 7.2 Mail settings 7.3 General page 7.4 Servers page 7.5 Retrieve 7.6 Advanced page 7.7 PCmail and Nokia 9290 Communicator 7.8 Compatible e-mail systems 7.9 Supported e-mail attachments 7.1 0 RFC (Request for Comments) documents
7.1 Introduction For reading and sending e-mail via the Nokia 9290 Commu- nicator remote e-mail client, you need to have an Internet Access P oint (IAP) configured to your Nokia 9290 Commu- nicator . For further information on how to configure IAPs, please refer to Chapter 6 â Nokia 9290 Communicator and Internet Service. Y ou also need to have an e-mail account that supports SMTP protocol for sending e-mail, and POP3 or IMAP4rev1 protocol for receiving e-mail. You can also have multiple e-mail accounts in the Nokia 9290 Communicator . Note: The necessary settings for mail configuration are provided by your e-mail service provider . Depending on your service pro vider , you may not need to fill in all of the settings. If your mail settings are incomplete or incorrect, please contact your service provider . An e-mail service provider can be your company or a commercial ISP , for example. Important information that must be filled in when defining a new e-mail account includes: ⢠Host name to receive mail (IMAP4 or POP3 e-mail server) ⢠Host name to send mail (SMTP server) ⢠Mailbox type (which protocol to use, either POP3 or IMAP4) ⢠Username (case sensitive) ⢠Password (case sensitive, displayed using asterisks (*)) ⢠Dial-in access point for the mail service ⢠Use of secure connection (i.e., require SSL/TLS encryption to be used) 7.2 Mail settings In order to connect to your electronic mailbox service, yo u need to define your remote mailbox on your Nokia 9290 Communicator . This can be made from the Messaging application main view under Menu (see figure below) or from that shortcut (Internet Start up) in the Desk application. To define a new remote mailbox: 1. Press the Menu key in the main view of the Messaging center and first select Tools, then Accounts. A list of accounts opens. 2. Press Create new to create an e-mail account. Y ouâÂÂll get the following dialog: 3. Select Email and press OK. A dialog with four pages opens. 4. Define the settings on the General, Servers, Retrieve, and Advanced pages below . 5. Y ou must fill in at least: ⢠Username used to log in the POP3/IMAP4 e-mail server ⢠Password for the POP3/IMAP4 e-mail server ⢠Y our e-mail address (e.g., for replies to messages you have sent) ⢠Outgoing e-mail server (host name for SMTP server) ⢠Incoming e-mail server (host name for IMAP4 or POP3 server) 6. Press Delete to discard any changes. 7. Press Close to accept the changes you have made. 7.3 General page 1. Enter the name of the remote mailbox under My account name. The name can be entered freely (e.g., My mail, Johnâ s mail, etc.). 2. T ype your name (note: your name appears here auto- matically if you have entered your contact card), username, and password. Tip: Usually the name and password are the same ones you use for your Internet Access P oint (PPP authentication). However , if your e-mail service pro vider is different from the Internet service provider , this may not be the case. Note that both the username and password are case-sensitive (capitalization of letters matters). If you do not specify a password, you will be prompted for one when you try to read mail in your remote mailbox. 3. My mail address: Type in the e-mail address given to you by your service provider . The address must contain the @ character . This address will be shown as the originating (From) address in your messages. 4. Choose the Internet Access P oint used for the mailbox. Choose from the list that contains all available IAPs. Note that you must be able to connect to the remote mailbox via the given IAP . For example, if you are accessing your companyâÂÂs intranet mailbox, you may need to use your companyâÂÂs intranet Internet Access P oint as well. 5. Choose Default account from the list, which contains all available mail accounts. 24
7.4 Servers page 1. Press the Menu key to activate the Servers tab . 2. Select Mail account type (POP3 or IMAP4). This defines the mail protocol your mailbox service provider recom- mends. If you are allowed to choose between these two protocols, you should select IMAP if you are working with multiple folders and receive a lot of attachments, and POP if you have a single incoming mail folder and receive no attachments. POP may be slightly faster in some situations, but IMAP gives the user more control over the mailbox and mail retrieval. Note that mailbox type cannot be changed after the e-mail account set- tings have been saved! 3. Enter the Outgoing mail server IP address or host name. This is also known as the SMTP server , sending server , or mail relay . When you are sending e-mail, your Nokia 9290 Communicator connects to this server and sends the mail. This server will then relay the mail towards the recipientâ s mail server (e.g. 123.123.123.123 or mail.server .com). 4. Enter the Incoming mail server IP address or host name. This is also known as the IMAP or POP server (depending on the account type) or the remote mailbox server . When you receive mail, the mail will be stored on this server . During mail retrieval, your Nokia 9290 Communicator connects to this server in order to download mail. 7.5 Retrieve Press the Menu key to activate the Retrieve tab and fill in the following settings: ⢠Retrieve: Choose what will be fetched from the remote mailbox when the connection is established. The options are: Message headers (stay online)/Messages and attachments/Messages. The last option is available only if the Mail account type is IMAP4. ⢠Max. size of message: The maximum size of a message that will be retrieved with the Retrieve mail command. The minimum is 1 and the maximum is 1000 kB (kilobytes). One kilobyte corresponds to approximately half of a written page of plain text. Max. size of message also includes attachments. ⢠Synchronize: Sync your mail folders. 7.6 Advanced page Press the Menu key to activate the Advanced tab and fill in the following settings if necessary . Contact your e-mail service provider for the correct settings. ⢠Default mail type: Select the type of mail that you can write and send from your Nokia 9290 Communicator . The options are Plain text/Plain text (no MIME)/ Formatted text (HTML). ⢠If you are using accented characters, you should use either Plain text or Formatted text. Otherwise, accented characters will not be transferred correctly . ⢠For the best compatibility across existing electronic mail systems, choose Plain text. If you are only com- municating with people with new , graphical e-mail systems, you can choose Formatted text. Formatted text may not be correctly shown to recipients with older , text-based e-mail systems. ⢠Use Plain text (no MIME) only if corresponding with people with old e-mail systems. ⢠Send mail: Choose how mail messages are sent from your Nokia 9290 Communicator . The options are Imme- diately/ During next connection/Upon request. ⢠Bear in mind that if you select During next connection, the mail will be sent during the next connection to that mailserver , not during the next connection to the Internet. ⢠Include signature: Select whether your signature is attached to sent mail. The options are No/Use my contact card/Custom. If you choose Custom, press Edit signature to create a signature. ⢠Request read report: Select whether you want to receive a report when the recipient has read your mail. The options are Y es/No. ⢠Not all e-mail software can generate a read report. A read report should not be used as proof that a mail has been read or not read. Usually the recipient can decide whether a read report will be generated or not. ⢠Some mail systems call read reports âÂÂread receiptsâ or âÂÂdisposition notifications. â â¢ Allow report requests: This option defines whether the Nokia 9290 Communicator will generate a âÂÂread reportâ mail to the Outbox if received mail requires it. The options are Y es/No. ⢠Read reports will be generated in your outbox. The Nokia 9290 Communicator will reply to standard disposition notification requests and some non- standard requests. Depending on the senderâÂÂs mail system, a read report may not be generated. If the senderâÂÂs mail system does not support standard disposition notifications, the mail system may not be capable of utilizing the information in the read report automatically . ⢠Copy to my mail address: Select whether you want to send a copy of sent mail to your own mail address. The options are Y es/No. 25
⢠Secure login (APOP): The options are Yes/No. Use of APOP increases security when connecting to a POP3 mail server . Please check with your e-mail service provider whether this option can be used. The option is available only if the used e-mail protocol is POP3. ⢠Note that this does not encrypt your mail or protect the mail itself in any way . This option just protects your password from being transmitted as plain text. ⢠Secure connection (TLS): Select whether to use TLS security when connecting to the mail server . The options are Yes/No. Please check with your e-mail service provider whether this option can be used. ⢠The mail server needs to support the standard âÂÂstarttlsâ or âÂÂstlsâ command (depending on the protocol) in order to be used with the Nokia 9290 Communi- cator . Som e older servers use a dedicated server port for secure connections over SSL. The Nokia 9290 Communicator does not support this non-standard system. ⢠Note that this only protects the transfer of your e-mail between the Nokia 9290 Communicator and the first server (either the sending server or your remote mailbox). When sending mail, it will be trans- ferred without any security from the first mail server onwards. Also, any mail you receive will have been transferred without any security to the remote mail server . ⢠When using security , both the sending and receiving servers must support secure connections. ⢠Enter IMAP4 folder path: (The folder path could be Inbox, for example.) This option is available only if the mailbox type is IMAP4. After you have filled in all details, press Close to close dialogs, and the new e-mail account will appear in the Messaging application as shown in the picture below . (The name of the remote mailbox is the name that you defined earlier .) New e-mail account in Messaging application Now you are ready to use the Retrieve mail command to connect to the newly defined e-mail account and fetch mes- sages. The very first time you connect to the IMAP4 account may take more time, depending on the number of mail messages in the remote Inbox and also the number of remote mail folders, because the device fetches message headers and scans remote folders for subscriptions. Subsequent Retrieve mail commands should work faster , as only changed folder data is downloaded to the device. Note: Once you have retrieved mail and you go offline, all the headers from your remote mailbox are sho wn in your Nokia 9290 CommunicatorâÂÂs Mail inbox. BE CAREFUL WHEN DELETING THEM, because if you delete them, they will be deleted from your Remote inbox, too, the next time you connect to your mailbox. T o avoid this situation, please refer to the Messaging chapter in the User Guide. Tip: When using an Internet Access P oint that uses a high- speed data call, and when you have to send large attachments or e-mails , you will get the fastest upload (sending) speed if you select âÂÂ28800â as the maximum transfer rate in the IAP settings. This involves the use of two GSM timeslots (28800 bits per second) in the uplink direction (from your Nokia 9290 Communicator to the mail server). All other transfer rates use just one GSM timeslot, 9600 or 14400 bits per second, in uplink direction. When downloading (receiving) mail, you will get the best performance by selecting the largest possible value as the maximum transfer rate. 7.7 PCmail and Nokia 9290 Communicator PCmail is a mail you can read, write, and edit on your Nokia 9290 Communicator , but which cannot be sent without your PC or laptop. PCmails are sent the next time you synchronize your Nokia 9290 Communicator to your PC or laptop. Internet mails can be converted to PCmails so that mails can be synchronized with your PC or laptop, or PCmails can be converted to Internet mails so that mails can be sent directly from the Nokia 9290 Communicator . Note: Refer to the Nokia 9290 Communicator User Guide for converting mails. 7.8 Compatible e-mail systems Here are listed mail systems that can be connected with the Nokia 9290 Communicator . All of these systems should work with the Nokia 9290 Communicator . This list is not exhaus- tive and other mail servers supporting standard Internet protocols (SMTP , IMAP4, and POP3) should work as well. Cyrus IMAPD Mail Server (http://asg.web .cmu.edu/cyrus/ ) ⢠Cyrus IMAPD Mail Server (Carnegie Mellon) supports MIME, IMAP4, and POP3 standards HP OpenMail (http://www .hp.com ) ⢠OpenMail 6.0 (for Linux) supports SMTP , MIME, IMAP4, and POP3 standards Lotus Domino Mail (http://www .lotus.com ) ⢠Lotus Domino R5 Mail Server supports SMTP , MIME, IMAP4, and POP3 standards Microsoft Exchange 5.5 (http://www .microsoft.com ) ⢠Microsoft Exchange 5.5 supports SMTP , MIME, IMAP4, and POP3 standards Microsoft Exchange 2000 (http://www .microsoft.com ) ⢠Microsoft Exchange 2000 supports SMTP , MIME, IMAP4, and POP3 standards Oracle InterOffice Mail Server (http://www .oracle.com) ⢠Oracle InterOffice Mail Server 5.1 supports the SMTP , MIME, IMAP4, and POP3 standards 26
Stalker CommuniGate Pro Mail Server (http://www .stalker .com/CommuniGatePro ) ⢠Stalker CommuniGate Pro 3.3 supports SMTP , MIME, IMAP4, and POP3 standards and also secure connec- tions (SSL/TLS). Also APOP command is supported for POP3. Sun Internet Mail Server (http://iplanet.com/ ) ⢠Sun Internet Mail Server 4.0 supports SMTP , MIME, POP3, and IMAP4 standards University of Washington IMAP4 Server (http://www .washington.edu/imap ) ⢠UW IMAP Server v1 0.173 supports POP3 and IMAP4 standards Zmailer (http://www .zmailer .org/ ) ⢠ZMailer (version 2.99) supports SMTP standard TeamW are Office Mail Server (http://www .teamware.com/products/ ) ⢠SMTP , MIME, POP3, and IMAP4 standards Other solutions If the e-mail server does not support POP3/IMAP4 and SMTP protocols, it may be possible to use converter software that provides necessary POP3/IMAP4 and SMTP protocol support for the e-mail server . Examples of converter software include Infinite InterChange by Infinite Technologies. Infinite InterChange creates POP3, IMAP4, and HTTP/HTML support. More information on the Infinite InterChange can be found at www .ihub .com . Additionally , connection to the e-mail server can also be established with the Nokia 9290 CommunicatorâÂÂs Web browser if the e-mail server supports HTTP/HTML access. Note: With the Nokia 9290 Communicator , you can also read W eb mails, i.e. Hotmail and Y ahoo mail. 27 7.9 Supported e-mail attachments E-mail attachments are supported and downloaded attachments that can be viewed on the Nokia 9290 Communicator . Initially supported attachment types are marked with an asterisk (*) in Table 1 (on the next page). Other attachment types in Table 1 are supported if the appropriate application or converter is installed to the device. New attachment types can be supported via add-on applications installed to the Nokia 9290 Communicator . Downloaded attachments can also be saved to files and transferred to a PC for viewing. Overall use of attachments is rather limited by the small disk space and amount of free memory . A memory card can be used to expand the available disk space for messaging. 7.1 0 RFC (Request for Comments) documents Internet e-mail protocols are specified using RFC (Request for Comments) documents. RFC documents are available, for example, from IETF (the Internet Engineering Task Force, www .ietf.org/ ). SMTP (Simple Mail T ransfer Protocol) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RFC 82 1 Standard for the format of ARPA Internet text messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RFC 822 POP3 (P ost Office Protocol, version 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RFC 1939 PPP (P oint to Point Protocol) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RFC 166 1 MIME (Multipurpose Internet Mail Extensions) P art One: Format of Internet Message Bodies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RFC 2045 MIME (Multipurpose Internet Mail Extensions) P art Two: Media T ypes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RFC 2046 MIME (Multipurpose Internet Mail Extensions) P art Three: Message Header Extensions for Non-ASCII Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RFC 2047 IMAP4 (Internet Message Access Protocol, version 4rev1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RFC 2060 TLS (T ransport Layer Security Protocol, version 1.0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RFC 2246 Read receipts (an Extensible Message Format for Message Disposition Notifications, Disposition-Notification-T o header) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RFC 2298 SMTP Service Extension for Secure SMTP over TLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RFC 2487 Using TLS with IMAP , POP3, and ACAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RFC 2595
28 Attachment type File extensions MIME T ypes Audio File WA V, AU, WVE âÂÂaudio/x-wavâ â audio/basicâ â audio/x-sibo-wveâ CompuServe GIF GIF âÂÂimage/gifâ Computer Graphics Metafile CGM âÂÂimage/cgmâ âÂÂimage/x-cgmâ Corel/Novell Presentations SHW âÂÂimage/x-presentationsâ Symbian OS Word* - Symbian OS Sheet* - Symbian OS Bitmap* MBM Internet HyperT ext Markup Language* HTML, HTM âÂÂtext/htmlâ Lotus 1-2-3 WQ1, WKU, WK1, WK3, â application/x-lotus-123â v .1/2/3/4/5/97/Millennium WK4, WK5, WK6, 123 â application/vnd.lotus-1-2-3â Lotus AMI Draw SDW âÂÂimage/x-amidrawâ Microsoft Excel XLS, XLC â application/x-msexcelâ 2/3/4/5/7/97/98/2000 â application/x-excelâ â application/vnd.ms-excelâ â application/msexcelâ â application/xlcâ Microsoft P owerPoint PPT , POT , PPS â application/x-mspowerpointâ 3/4/7/97/98/2000 â application/vnd.ms-powerpointâ â application/pptâ â application/potâ â application/ppsâ â application/mspowerpointâ Microsoft Project MPP â application/vnd.ms-projectâ Microsoft W ord DOC, WRI â application/mswordâ 1/2/3/4/5/6/7/97/98/2000 â application/vnd.ms-wordâ â application/vnd.mswordâ P aintbrush PCX, DCX âÂÂimage/x-pc-paintbrushâ PKZIP Format ZIP â application/zipâ P ortable Network Graphics PNG âÂÂimage/pngâ âÂÂimage/x-pngâ Rich T ext Format RTF â application/rtfâ Ringing T ones* MG â application/vnd.nokia.ringing-toneâ Tagged Image File Format (TIFF , JPEG) TIF , JPG, JIF âÂÂimage/tiffâ âÂÂimage/jpegâ Text* TXT âÂÂtext/plainâ vCard VCF âÂÂtext/x-vcardâ vCalendar VCS âÂÂtext/x-vcalendarâ Visio VSD â application/vnd.visioâ Windows Bitmap BMP , RLE, ICO , CUR âÂÂimage/x-win-bitmapâ âÂÂimage/x-MS-bmpâ âÂÂimage/bmpâ âÂÂimage/x-bmpâ Windows Metafile WMF , EMF âÂÂimage/x-win-metafileâ âÂÂimage/x-wmfâ WordP erfect WPD â application/wordperfect5â 4/5/6/7/8 â application/wordperfect5.1â â application/x-wordperfect6â Table 1 Supported e-mail attachments The Nokia 9290 Communicator supports the following e-mail attachment types:
8. NOKIA 9290 COMMUNICA T OR AND W AP SERVICE Contents: 8.1 Introduction 8.2 Defining WAP access points manually 8.3 Setting home page 8.4 Supported images, their suffixes, and MIME-types
8.1 Introduction Before you can use the WAP services, you need to configure your W AP settings. Y our WAP service provider will provide you with the exact values for the W AP settings. Follow the instructions carefully . Y ou can use this information to define and edit the settings manually . Also, your service provider may be able to send some, or all, of the required settings to you via a special short message called an Over the Air (OT A) message. After you have received the settings, you can start using the WAP applica- tion or edit the settings as described below . Note: The necessary settings for WAP configuration are provided by your W AP service pro vider . Depending on your service pro vider , you may not need to fill in all of the settings. 8.2 Defining WAP access points manually To set up a new W AP access point, open Internet startup under the Extras application, and select WAP access (a shortcut to Internet startup can also be found in the Desk application). 1. Open Internet startup from Desk or from under Extras. 2. Select WAP access and press Open. 3. Fill in the following settings. Contact your WAP service provider for the correct settings. ⢠Name â Create a name for the access point that you can recognize easily . ⢠Secure connection â Choose whether to Use secure connection, according to your service providerâÂÂs instructions. ⢠Internet access â From a selection list, choose the Internet Access Point (IAP) you want to use for this connection. If you have no configured IAPs, you can create a new one by pressing New Internet access. ⢠Gateway IP address â T ype in the IP address that the WAP gateway uses. 4. Press Close to exit the WAP access point settings. 8.3 Setting home page 1. Press the Internet button and open the W AP application. 2. Press the Menu key , and open the Settings dialog under the T ools menu. 3. T o activate the Home page tab, press the Menu button. 4. T ype in the WAP home page URL. 5. Choose the WAP access point you want to use. 6. Press Done to exit the WAP settings. 8.4 Supported images, their suffixes , and MIME-types In addition to WBMP image format, the Nokia 9290 Communicator supports all the most commonly known image formats. Note: Some WAP gateways may not support all of these content types. Nokia W AP gateway products support all the content types listed here: ⢠a WBMP (Wireless Bitmap), âÂÂimage/vnd.wap.wbmpâ â¢ a JPEG file (incl. Progressive), â .JPGâÂÂ, âÂÂimage/jpegâ â¢ a GIF file (incl. anim-gif), â .GIFâÂÂ, âÂÂimage/gifâ â¢ a PNG file, â .PNGâÂÂ, âÂÂimage/pngâ The WAP Service Developerâ s Guide for the Nokia 9290 Com- municator , which is available at www .forum.nokia.com , contains more detailed information about WAP and the Nokia 9290 Communicator . 30
9. NOKIA 9290 COMMUNICA T OR AND REMO TE / OVER THE AIR (O TA) CONFIGURING Contents: 9.1 General 9.2 Further information and support 9.3 Creating configuration messages 9.3.1 Configuration over SMS only 9.3.2 Non-supported feature sets 9.3.3 Further deviations
9.1 General This chapter shows how the Nokia 9290 Communicator can be configured remotely using SymbianâÂÂs Bearer Indepen- dent Object (BIO) messaging. Remote configuration helps the end user to get the most out of the device as quickly as possible. Complex settings, such as Internet settings, can be âÂÂpushedâ to the device by the carrier or the help desk of an Internet service provider or a corporate IT department. The configuration messages are sent to the Nokia 9290 Communicator using the GSM Short Message Service (SMS). For maximizing the compatibility and minimizing the transition period for help desks, the BIO messaging support for the Nokia 9290 Communicator is similar to Nokia Smart Messaging, which is supported by earlier Nokia 9290 Communicators. The development of the Symbian platform may introduce new BIO message types in the future that leverage the new features of the Nokia 9290 Communicator and the Symbian operating system. WAP settings can be configured using OT A (Over the Air) configuration syntax. 9.2 Further information and support The supported message syntax is based on Smart Messaging Specification 3.0.0, Nokia Mobile Phones, 2000. The document is available from the Forum Nokia W eb site at www .forum.nokia.com/, Smart Messaging section. The syntax for W AP settings is based on WAP Over the Air settings specifications, available from the Forum Nokia Web site at www .forum.nokia.com/, Smart Messaging section. For details on what the Internet settings mean, please refer to chapters 5 and 6 in this document. 9.3 Creating configuration messages The creation and syntax of Smart Messaging-type config- uration messages is specified in the Smart Messaging specification mentioned in section 9.2. That specification contains the details on how the messages should be created and sent. The following sections list the deviations from that specification. 9.3.1 Configuration over SMS only At the moment, the only way to transfer a configuration message to the Nokia 9290 Communicator is over the GSM Short Message Service. T ransferring the configuration messages over HTTP (in Web) or as e-mail attachments is not supported yet. The Nokia 9290 Communicator is a WAP device and as such all Smart Messages should be sent to WDP ports, as specified in the Smart Messaging specification. If this is not possible, keyword headers (also known as compatibility headers) can also be used. NBS port numbers, on the other hand, should not be used. 9.3.2 Non-supported feature sets Some of the following feature sets were specified in older versions of the Smart Messaging document. They are listed for the sake of completeness. ⢠TTML (T agged Text Markup Language) is considered as âÂÂdeprecated.â WAP and WML have replaced TTML. The Nokia 9290 Communicator does not support TTML. ⢠DMCP (Dynamic Menu Control Protocol) is not sup- ported by the Nokia 9290 Communicator . The majority of features are activated from the PDA side of the Nokia 9290 Communicator; therefore, dynamic menus on the phone side are not supported. ⢠Service Cards are not supported. Service Card func- tionality can be used with normal business cards that have a phone number field for each service. T o converge with the de facto standards, the Nokia 9290 Communicator supports the vCard business card format, which can be used for this purpose. ⢠Extended Configuration Syntax is not supported at the moment, except for the Short Message Center number setting. 9.3.3 Further deviations ⢠The Notify text field in the basic Internet configuration message is now optional, rather than mandatory . Hence, the first line of the definition now reads: <iap-message> ::= [<iap-compatibility-header>] [<notify-text>] <info-body> ⢠Script version and script data fields in Internet configuration settings are not used in the Nokia 9290 Communicator . 32
1 0. NOKIA 9290 COMMUNICA TOR AND SECURITY Contents: 1 0.1 Hardware and SIM card security 1 0.2 Radio interface security 1 0.3 Software security 1 0.4 Internet and intranet 1 0.4.1 Incoming data calls 1 0.4.2 Attacks from the Internet 1 0.4.3 Dial-up security 1 0.5 SSL and TLS 1 0.5.1 Web browser 1 0.5.2 Reading and sending mail 1 0.5.3 Supported encryption algorithms 1 0.6 WAP security
1 0.1 Hardware and SIM card security The following security methods can be used to ensure Nokia 9290 Communicator hardware and SIM card security (for details and activation/deactivation, please refer to the Nokia 9290 Communicator User Guide): ⢠PIN code & PUK code ⢠Security code for SIM change security ⢠Device lock â to lock the whole device ⢠Call restriction â to restrict incoming or outgoing calls 1 0.2 Radio interface security The security of the radio connection between a GSM phone and the GSM network is specified in the GSM standards. The GSM network specifies the radio interface security level, and the encryption applies to voice, data, and fax calls. Note that encryption is only used between the GSM phone and the base station. The level of security in the radio transmissions depends on the network and the local laws. GSM short messages (SMS) are transported using the GSM signaling channels, but these signaling channels are not encrypted. Therefore, short messages are not a secure way to transport data. 1 0.3 Software security As the Nokia 9290 Communicator is a versatile and open programming environment, anyone can create new software for it. The Nokia 9290 Communicator has a secure software installation system that can be used to minimize the risks posed by the possible malicious software. Software is distributed in software packages called SIS files. These packages can be digitally signed. By signing a soft- ware package, the originator of the package makes sure that the package cannot be modified while it is being stored, or while it is en route to the Nokia 9290 Communicator . When installing software, the user will see the alleged originator of the package and the party that authenticates the originatorâ s identity . T o view the currently trusted certification authorities, the user can go to the Certificate management tool. The user can edit trust settings for each listed certificate. By giving a certificate a âÂÂtrustedâ status, the user vouches that he/she knows that a given certificate really belongs to the given entity . In order to maximize software security in your Nokia 9290 Communicator: ⢠When editing trust parameters in the Certificate management tool in Control panel, only trust those certificates whose origin you can be sure of, and you know that the certificate really belongs to the entity whose name is on the certificate. If you are in doubt, contact the certification authorities help desk and ask them for their certificate âÂÂMD5 fingerprint.â Compare the âÂÂfingerprintâ with the one that is displayed in the Certificate management tool. ⢠Make sure that the software is intended for the Nokia 9290 Communicator . ⢠Only install software that comes in SIS files. Never install raw DLLs or EXEs. ⢠Only install software that has been signed and only if you trust both the author and the certification authority . ⢠During the installation, be sure to read the dialogs that are presented to you. They may contain further security information. ⢠Nokia runs a Nokia OK logo program for third-party software developers. Using software that has the Nokia OK logo offers further assurances on the quality of the software. 1 0.4 Internet and intranet Data communications over the Internet or other IP networks is not secure by default. To enable secure connections, the Nokia 9290 Communicator supports various security protocols. 1 0.4.1 Incoming data calls By relying only on the factory configuration, it is not possible to access the Nokia 9290 CommunicatorâÂÂs files from an incoming data call. However , as with any normal computer , malicious third-party software can potentially degrade the security of the device. Therefore, only install and use soft- ware that comes from a trusted source and is digitally signed by a trusted party . 1 0.4.2 Attacks from the Internet When the Internet connection is up, it is possible to send data packets from the Internet to the Nokia 9290 Commu- nicator . As the wireless link is low-bandwidth, it is potentially possible to cause congestion by sending large amounts of bogus packets to the device. Therefore, it is recommended that the dial-up link uses a firewall to filter suspicious packets. Many Internet service providers offer this service. The use of dynamic IP addresses is another recommended safety measure. Most, if not all, Internet service providers supply dial-in clients with dynamic IP addresses by default. Also, installing defective or malicious third-party software (especially from Internet servers) in Nokia 9290 Communica- tors may degrade the security . Only install and use software that comes from a trusted source and is digitally signed by a trusted party . 1 0.4.3 Dial-up security The Nokia 9290 Communicator requires a PPP (P oint to P oint Protocol) connection to allow connection to the Internet/intranet. The supported authentication protocols are P AP (P assword Authentication Protocol) [RFC 1334], CHAP (Challenge Handshake Authentication Protocol) [RFC 1994], and MS-CHAP (Microsoft variant of CHAP). 34
To enhance the security of P AP , CHAP , and MS-CHAP , some other authentication methods can be used when creating a network connection. If the method works with normal PAP or CHAP , it can be used with the Nokia 9290 Communicator . Other login schemes can be supported using a login script. Some of the alternatives are: ⢠Callback system (supported PPP callback protocols: IETF type 0 [RFC 1570] and the Microsoft callback protocol) ⢠Centralized security (authentication server configured based on RADIUS [RFC 2 138] and TACACS [RFC 1492]) ⢠Multiple P asswords and one-time password schemes ⢠Token-based security 1 0.5 SSL and TLS The Nokia 9290 Communicator supports the SSLv3 (Secure Socket Layer) and TLSv1 (Transport Layer Security) protocols. These protocols are integrated in the socket interface, so third-party programs can easily use these protocols to offer secure Internet connections. 1 0.5.1 Web browser Web URLs (addresses) that start with âÂÂhttpsâ are SSL-secured connections. The SSL connection is negotiated with t he server and then the data is transferred over the encrypted connection. A small lock symbol is displayed as an indication that the connection is encrypted. The encryption strength depends on the SSL server . The Nokia 9290 Communicator supports strong 128 bit encryption in SSL and TLS, but can downgrade its security to a lower level if the server is not capable of handling such strong encryption. The authenticity of the Web server is determined by the help of certificates in the Certificate management tool. As discussed above in the software security chapter , the user can select which certificates are trusted and which are not. When connecting to a server , whose identity is certified by a trusted party , there will be no warning note. Other- wise, the user will be able to review the identification offered by the remote server . Some certification authority root certificates are factory-installed on the device; Nokia does not endorse any specific certification authority . The HTTP (Hypertext T ransfer Protocol) also provides a simple authentication protocol, which uses a username/ password pair . It can be used to authenticate the user to a remote server . This method can be used over the SSL for additional security . 1 0.5.2 Reading and sending mail Access to remote mailboxes (IMAP and POP) and sending mail (SMTP) can also be secured using the SSL/TLS. Y ou can request a secure connection by ticking the appropriate box in the settings. In order to use secure connections with electronic mail, the mail server has to support the âÂÂstarttlsâ command (IMAP , SMTP) or the âÂÂstlsâ command (POP). Note: Sending electronic mail o ver a secure connection does not encrypt the mail itself, only the connection to the mail server . After the mail continues to its destination from the first mail server , it is not encrypted. This feature is most useful when accessing mail servers in a secure intranet through a public Internet service provider . 1 0.5.3 Supported encryption algorithms The selection of algorithms depends on the protocol being used. It is advisable to avoid the use of â export-gradeâ algorithms (RC4 with 40 secret bits and DES) for security reasons. The Nokia 9290 Communicator supports the following cryptographic algorithms in SSL/TLS: ⢠For server authentication and/or key exchange: RSA, DSA, and Diffie-Hellman ⢠For data encryption: RC4⢠(plus the âÂÂexportâ version with 40 secret bits), DES, and Triple-DES 1 0.6 WAP security When using WAP for a data call, the dial-up security is the same as with Internet services. Please refer to the chapter above. WAP uses an optional security layer called WTLS. This can be turned on in the settings, or the server can mandate it. WTLS security ends at the WAP gateway . Connections to the target server from the WAP gateway might not be encrypted. WAP Forum specifies WTLS. The Nokia 9290 Communicator supports strong 128 bit encryption in WTLS, but is able to lower the security level if required by the server . The Nokia 9290 Communicator supports server authentication and key exchange using the RSA algorithm and data encryption using the RC5⢠algorithm. The gateway is authenticated using certificates. Some certification authority root certifi- cates are factory-installed on the device; Nokia does not endorse any specific certification authority . 35
1 1. FORUM NOKIA - COMMUNITY FOR DEVELOPERS Contents: 1 1.1 Introduction 1 1.2 Information for Symbian application developers 1 1.3 Developing optimized WAP services 1 1.4 Nokia Developer ProPoint 1 1.5 Third-party connectivity solutions
1 1.1 Introduction Forum Nokia is an online community for third parties developing applications and services for Nokia platforms. The Forum Nokia Web site provides information for different technologies and platforms for developers, system integrators, content providers, and for others who are interested in the mobile application development. Marketing support as well as possibility for application certification is provided via the developer alliances, Nokia Developer ProP oint, and Nokia Developer NetP oint. After free registration to Forum Nokia, the registered members can find supporting documents, toolkits, and software development kits (SDKs) and share development tips and find solutions to problems in the Online Discus- sion areas. Y ou can find the Forum Nokia Web site at www .forum.nokia.com . 1 1.2 Information for Symbian application developers As the Symbian operating system of the Nokia 9290 Communicator is an open platform by Symbian, third-party developers can create additional software applications for the Nokia 9290 Communicator . The Symbian application developers can register to the Symbian Platform section in Forum Nokia. Besides downloading supporting documents, the Software Development Kit (SDK) for Symbian operating system application development can be ordered here. The SDK CD-ROM includes both the C SDK and Java⢠SDK, and both programming languages can be used in the application development. 1 1.3 Developing optimized WAP services Forum Nokia also offers guidance in developing optimized WAP services for the Nokia 9290 Communicator , as well as for other Nokia WAP phones. The Nokia W AP Toolkits can be downloaded for free, and several WAP service development related discussion areas are on hand. 1 1.4 Nokia Developer ProPoint Companies that want to develop applications and services in closer relationship with Nokia can apply for the Nokia Developer ProP oint. Members of Nokia Developer ProPoint can get technical assistance, marketing support, and other membership benefits during their membership period. See the Forum Nokia Web site at www .forum.nokia.com for further information on services, price, and availability . 1 1.5 Third-party connectivity solutions Since the Nokia 9290 Communicator has both an infrared and a serial port, it is possible to connect different kinds of external devices to it. Third-party connectivity solutions include, for example, bar code readers, GPS receivers, digital still cameras, and portable scanner applications. 37
12. ABBREVIA TION
39 Abbreviation: bps bits per second CHAP Challenge Handshake Authentication Protocol CMT Cellular Mobile Telephone DNS Domain Name Server DTMF Dual Tone Multi Frequency GSM Global Digital System for Mobile Communications HSCSD High Speed Circuit Switched Data HTML HyperText Markup Language IAP Internet Access Point IMAP Internet Mail Access Protocol IP Internet Protocol IrDA Infrared Data Association ISP Internet Service Provider IT Information T echnology MIME Multi-purpose Internet Mail Extensions MMC MultimediaCard NIM Nokia Interleaved Multimedia PAP P assword Authentication Protocol PDA P ersonal Digital Assistant POP P ost Office Protocol PPP P oint to Point Protocol SIM Subscription Identification Module SMSC Short Message Service Center SMTP Simple Mail Transfer Protocol SSL Secure Socket Layer TCP Transport Control Protocol TLS Transport Layer Security URL Uniform Resource Locator USSD Unstructured Supplementary Service Data WAP Wireless Application Protocol WML Wireless Markup Language WWW World Wide Web
13. SHORT CUTS FOR THE NOKIA 9290 COMMUNICA T OR
41 The Nokia 9290 Communicator supports Windows TM -like shortcuts. The table below lists some of the available shortcuts: Shortcuts for the Nokia 9290 Communicator: Tip: Y ou can find more shortcuts in the menus on the display of the Nokia 9290 Communicator interface. Shortcut Function Ctrl a Selects all Ctrl c Copies selected text Ctrl x Cuts selected text Ctrl v P astes selected text Ctrl z Undoes (the last action) Ctrl b Applies bold Ctrl i Applies italics Ctrl u Applies underlining Ctrl t Full screen mode (if available) Ctrl d Delete files, messages, shortcuts, and other items Ctrl p Print or Properties Ctrl n Creates a new file Ctrl o Open Ctrl e Close Ctrl s Save Ctrl Shift s Save As Chr left/right arrow (on Arrows key) Moves the cursor to the beginning or end of the line Chr up/down arrow (on Arrows key) Moves up or down a page Chr Ctrl up/down arrow (on Arrows key) Moves to start or end of document Shift Ctrl left/right arrow (on Arrows key) Selects the previous or next word Shift right/left/up/down arrow (on Arrows key) Selects one text character or line Shift Chr up/down arrow (on Arrows key) Selects text, page by page, inside a document
14. SETUP CHECKLIST
43 For online Help at any time, press the key on the Nokia 9290 Communicator keyboard. Y ou are shown a page of information relevant to the task you are doing. Y ou can also search the Help topics for specific subjects and keywords. Setup checklist MAIL SMS INTERNET WA P Information you need Where to obtain it Where to insert it Write it here Mail address of your remote If you have an existing mail See âÂÂMailâ in the User Guide. mailbox account, this address is your The General page of Mail mail address settings dialog: Your mail address Username and password of Y our mailbox service Username and Password your mailbox provider IAP to connect to your mailbox Y our mailbox service Use Internet access point provider The protocol of your remote Y our mailbox service The Servers page: POP3 or IMAP4 mailbox provider Mailbox type IP (Internet Protocol) address Y our mailbox service Outgoing mail server or host name of the server that provider sends your mail IP address or host name of the Y our mailbox service Incoming mail server server that receives your mail provider Service center number Home network carrier See âÂÂSMSâ in the User Guide. The Settings page of the SMS settings dialog: Service center in use WWW Internet access point: Y our Internet service See âÂÂInternet connectionsâ name, modem phone number , provider in the User Guide. Internet username, and password access, connections details dialog Data call type information: Y our GSM network carrier Internet access, connection whether high-speed call details dialog, Advanced settings, Data Call page Data call type information: Y our Internet service As above remote modem type provider WAP Internet access point: Y our WAP service provider See âÂÂW APâ in the User Guide. name, modem phone number , Internet access, connection username, and password settings dialog Data call type information: Your GSM network carrier Internet access, connection whether high-speed call details dialog, Advanced settings, Data Call page Data call type information: Your WAP service provider As above remote modem type WAP Internet access point: Y our WAP service provider WAP access point settings gateway IP address dialog
Legal Notices Reproduction, transfer , distribution, or storage of part or all of the contents in this document in any form without prior written permission of Nokia is prohibited. Copyright é 2002 Nokia. All rights reserved. Nokia, Nokia Connecting P eople, Nokia 9290 and Nokia original accessories logo are trademarks or registered trademarks of Nokia Corporation. Java is a trademark of Sun Microsystems, Inc. Other company and product names mentioned herein may be trademarks or trade names of their respective owners. Nokia operates a policy of ongoing development. Nokia reserves the right to make changes and improvements to any of the product s described in this document without prior written notice. UNDER NO CIRCUMSTANCES SHALL NOKIA BE RESPONSIBLE FOR ANY LOSS OF PROFITS, INCOME, DAT A, REVENUE OR TIME OR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL INDIRECT OR PUNITIVE DAMAGES HOWSOEVER CAUSED. THE CONTENTS OF THIS DOCUMENT ARE PROVIDED âÂÂAS IS.â EXCEPT AS REQUIRED BY APPLICABLE LA W, NO WARRANTIES OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO , THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE MADE IN RELA TION TO THE ACCURACY, RELIABILITY OR CONTENTS OF THIS DOCUMENT . NOKIA RESERVES THE RIGHT TO REVISE THIS DOCUMENT OR WITHDRAW IT AT ANYTIME WITHOUT PRIOR NOTICE. Important Safety Notes All the safety instructions in your phoneâÂÂs user guide and computer also apply when this product is used with the phone. Remember to make backup copies of all important data to protect against possible loss or alteration. Do not point the infrared beam into anyoneâÂÂs eyes or allow it to interfere with other infrared devices. To disconnect the cable from the Nokia Communicator , hold the connector and remove the cable. Export Controls This product contains commodities, technology , or software exported from the United States in accordance with the Export Administration regulations. Diversion Contrary to U.S. law is prohibited. FCC/Industry Canada Notice Your phone may cause TV or radio interference (for example, when using a telephone in close proximity to receiving equipment). The FCC or Industry Canada can require you to stop using your telephone if such interference cannot be eliminated. If you require assistance, contact your local service f acility . This device complies with part 15 of the FCC rules. Operation is subject to condition that this device does not cause harmful interference. Please refer to the Nokia 9290 Communicator user guide (also available at www .Communicatorworld.net or www .nokia.com ) to learn more about this productâÂÂs features. Learn about Nokia products and Nokia at www .nokia.com . Nokia is a broadly held company with listings on six major exchanges, including the New York Stock Exchange (NYSE symbol: NOK).
Nokia Inc. 7725 Woodland Center Boulevard, Suite 150, T ampa, Florida 33614 www .nokia.com www .Communicatorworld.net 1-800- 4MY -9290 Copyright é 2002 Nokia. All rights reserved. Nokia, Nokia Connecting P eople, Nokia 9290 and Nokia original accessories logo are trademarks or registered trademarks of Nokia Corporation. N4125 5/0 2
Chapter Section Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Nokia 9290 Communicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 PC connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Nokia 9290 Communicator and data services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Nokia 9290 Communicator and Internet service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Nokia 9290 Communicator and e-mail service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Nokia 9290 Communicator and WAP service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Nokia 9290 Communicator and remote/Over the Air (OT A) configuring . . . . . . . . . . 9 Nokia 9290 Communicator and security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 0 Forum Nokia â community for developers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1 Abbreviation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 Shortcuts for the Nokia 9290 Communicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Setup checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1. INTRODUCTION This guide is intended mainly for the IT and Help Desk personnel of Carriers, Corporations, or Internet Service Providers. The following pages provide information to understand the func- tionality of the Nokia 9290 Communicator and the requirements to set up the data call, e-mail, WWW , and WAP services. This guide can also be used as a general technical specification document for the Nokia 9290 Communicator . Please note that this guide is not a substitute for the Nokia 9290 CommunicatorâÂÂs User Guide. The User Guide contains more detailed information about the use of the Nokia 9290 Communicator and should be referred to when step-by-step user instructions are needed. More Nokia 9290 Communicator product information and end- user support can be found at www .Communicatorworld.net ; developer support can be found at www .forum.nokia.com .
2. NOKIA 9290 COMMUNICA TOR Contents: 2.1 Technical specification 2.2 GSM phone feature list 2.3 Content of the sales package 2.4 Optional Nokia original accessories 2.5 To use the phone
2.1 Technical specification Applications ⢠Cellular mobile phone (handsfree, handset, car kit, and headset use) ⢠Desk application with background image and links ⢠Messaging includes SMS, fax, and e-mail ⢠Internet services include WWW and W AP ⢠Contacts ⢠Calendar ⢠Office includes Document, Sheet, File manager , and Presentation viewer ⢠Extras: Calculator , Clock, Games, Recorder , Unit converter , Imaging (Digital camera connectivity), Video player Note: Additional applications can also be found on the CD-ROM in the sales package. Size ⢠Dimensions: 6.22 x 2.20 x 1.06 in. ⢠Weight: 8.6 oz. Technical data ⢠GSM 1900 ⢠32-bit ARM9-based RISC CPU ⢠Operating system: Symbian OS ⢠Memory card slot ⢠Connectivity: IrDA, Ir-TranP , RS-232 ⢠Low power consumption ⢠Active matrix color display with 4,096 colors ⢠Java⢠support ⢠Supports HSCSD* E-mail protocols ⢠POP3 or IMAP4 (Nokia 9290 Communicator supports IMAP4rev1) ⢠SMTP ⢠MIME ⢠MHTML Supported mail servers* ⢠Cyrus IMAPD Mail Server ⢠HP OpenMail ⢠Lotus Domino Mail R5 ⢠Microsoft Exchange ⢠Netscape Messaging Server ⢠Stalker CommuniGate Pro Mail Server ⢠Sun Internet Mail Server ⢠University of Washington IMAP4 Server ⢠Oracle InterOffice Mail Server ⢠Teamware Office Mail Server ⢠Zmailer * Network dependent Attachments/files supported ⢠View ASCII text, and JPEG or GIF graphics ⢠View and edit Word 95/97/2000 and Excel 95/97/2000 documents ⢠View Microsoft PowerP oint 97/2000 slides ⢠View W ordP erfect 7.0/8.0 and Lotus 1-2-3 for SmartSuite for the Millennium ⢠Winzip supported (unzip) â (third-party application required) ⢠WAV audio files Nokia 9290 PC Suite for Nokia 9290 Communicator ⢠For use in Microsoft Windows 95/98/2000 and Microsoft Windows NT 4.0 environments File conversion support ⢠Symbian OS Word <---> Rich T ext Format, Text (MS-DOS), T ext (Windows ANSI), Word 6.0, Word 95, Word 97, Word 2000 ⢠Symbian OS Sheet <---> Excel 5.0, 95, Excel 97, Excel 2000 Calendar and contacts compatibility ⢠Microsoft Schedule 7.x ⢠Microsoft Outlook 97/98/2000 ⢠Lotus Notes 4.5, 4.6, and 5.0 ⢠Lotus Organizer 97, 5.0, 6.0, and GS/4.0 ⢠SyncML remote synchronization (contacts/calendar) Additional software on CD-ROM in sales package ⢠Many Nokia 9290 Communicator applications ⢠PC software ⢠Nokia 9290 PC Suite for Nokia 9290 Communicator ⢠Multimedia converter ⢠Documentation Battery performance Battery Talk/data/ Standby Standby Charging fax time time time time (phone on) (phone off) High-power up to 10 h up to 230 h up to 400 h 3 h Battery BLL-3 1300 mAh Li-Ion 4 Battery information is provided for comparison purposes. Talk and standby times are estimates and vary based on many factors. For complete battery information for this phone and a list of major factors impacting charge times, please refer to www .nokia.com or the phoneâÂÂs user guide.
2.2 GSM phone feature list Display & keypad ⢠Up to five lines for text and status indicators ⢠Indicators (e.g., incoming messages and call forwarding) ⢠Service provider indicator ⢠Welcome message ⢠Menu help texts after a time out ⢠Last digit and full display clear ⢠Full screen cursor editor ⢠One-touch voice mail button ⢠International access ( ) function ⢠Keyguard ⢠Language dependent keymappings ⢠Special characters under â key while in alpha mode ⢠Changing character case by pressing # key once ⢠Illumination Phone features ⢠Customizable profiles (set up from Nokia 9290 Communicator interface) ⢠Clock ⢠Alarm clock (activated from Nokia 9290 Communicator interface, stop alarm also from phone side) Call management ⢠One-key calling: locations 1 to 9 (1 is always voice mail) ⢠Last number redial ⢠Anykey answer ⢠Automatic redial ⢠Automatic answer (works with headset or car kit only) ⢠Supports emergency calls without SIM ⢠One-touch dialing ⢠Conference calling ⢠Call waiting, call hold ⢠Call/fax/data forward, separate for voice, fax and data ⢠Automatic and manual network selection ⢠Alternate line service ⢠Call transfer ⢠Closed user group ⢠Fixed dialing number ⢠Dual T one Multi Frequency (DTMF) signal transmitting ⢠DTMF control characters (pause, wait) ⢠Calling line identification presentation (CLIP) ⢠Calling line identification restriction (CLIR) ⢠Connected number identification presentation (COLP , COLR) ⢠CLI-based caller groups, a ringing tone, and calling priority ⢠Recent calls list with time stamp (Dialed/Received/Missed calls) Phone book memory ⢠The phone book supports multiple name entries per name ⢠Thousands of memory locations (depending on the Nokia 9290 Communicator memory) ⢠Names with multiple numbers (mobile, home, fax) ⢠Up to 250 numbers on the SIM card (SIM specific) Short Message Service ⢠Mobile Originated (MO), send ⢠Mobile T erminated (MT), receive ⢠Message class 0, 1, 2, 3 supported ⢠Easy to call number in message ⢠Sent message delivery report ⢠Cell Broadcast ⢠Multiple SMS sending ⢠Long messages concatenated with nine messages up to 1,337 characters in one message (concatenated with 30 messages in one message up to 4,590 characters in Nokia 9290 Communicator interface)* * Network dependent 5
Security and cost control ⢠Electronic keyguard (Menu â ) ⢠Security code (when a non-owner SIM is inserted) ⢠Device lock ⢠PIN1, PIN2 ⢠Advice of charge ⢠Call restriction ⢠Last and cumulative call timer Other controls V olume control ⢠Number of volume levels: 1 0 ⢠Separate voice volume level settings for handportable, car handsfree, and headset mode ⢠In-call volume control with the scroll keys P ower control ⢠Ignition switching time-out: 45 seconds ⢠Car kit power off: 12 h ⢠Automatic power save if no network available Tone control ⢠Several ringing tones ⢠Ringing types: ascending ringing, normal ringing, WA V, ring once, silent, priority group(s) only ⢠Keypad tone levels: 4 (from off to 3) ⢠Ringing tone levels: 6 (from silent to 5) ⢠SMS/fax/e-mail/clock alarm/calendar alert tones: standard, silent, WAV (volume level can be set separately for each application tone operated from Nokia 9290 Communicator interface) ⢠Downloadable ringing tones Over the Air SMS/Smart messaging Data calls ⢠Data calls send and receive ⢠Fax calls send and receive ⢠Data speeds up to 14.4 kbps SCSD* ⢠Data speeds up to 43.2 kbps HCSD* System specific features ⢠GSM phase 2 signaling ⢠3V SIM Application Toolkit support ⢠Enhanced full rate (EFR) speech codec ⢠Full rate speech codec ⢠Encryption algorithms: none, A5.1, A5.2 ⢠Discontinuous transmission (DTX) ⢠Cell broadcast (DRX) ⢠USSD (mobile originated and terminated) ⢠SIM Application Toolkit (Class 1.bis) * Network dependent Smart messaging (Over the Air SMS) features ⢠Name and number (business card) sending and receiving ⢠Calendar note sending and receiving (Nokia 9290 Communicator interface) ⢠Ringing tone receiving (Nokia 9290 Communicator interface) ⢠Carrier logo receiving ⢠WAP (operated from Nokia 9290 Communicator interface) ⢠WWW settings (access point), (operated from Nokia 9290 Communicator interface) Infrared features ⢠Name and number receiving (vCard) ⢠Calendar note receiving (vCal) ⢠File transfer between Nokia 9290 Communicators ⢠Digital camera connectivity ⢠Receiving is activated from Nokia 9290 Communicator or phone interface, sending from Nokia 9290 Communicator interface Note 1: Some of the above features are network dependent. Note 2: In the case of local network dependent features or other market specific features (such as languages, ALS), parties shall agree separately in writing if the feature is activated. 2.3 Content of the sales package The Nokia 9290 Communicator sales package contains the following articles (however , the content may vary due to country specific requirements): ⢠Transceiver (Nokia 9290 Communicator) ⢠High-power Battery BLL-3 (1300 mAh Li-Ion) ⢠16 MB MMC Memory Card ⢠Performance Travel Charger ACP-12U ⢠RS-232 Adapter Cable DLR-2L ⢠Folder ⢠User Guide ⢠Getting Started Guide ⢠Third-party application guide ⢠CD-ROM (Nokia 9290 PC Suite, additional Nokia 9290 Communicator software, and documentation) ⢠W arranty card 6
2.4 Optional Nokia original accessories The following optional Nokia original accessories are available for the Nokia 9290 Communicator: ⢠Advanced Desktop Stand DCH-1 0 ⢠High-power Battery BLL-3 ⢠Performance Travel Charger ACP-12U ⢠Advanced HF Car Kit CARK-1 09 ⢠Mobile Charger LCH-9 ⢠Headset HDC-8L ⢠Carry Case (vertical and horizontal styles) ⢠Memory Card (64 MB) ⢠RS-232 Adapter Cable DLR-2L 2.5 To use the phone To be able to send and receive calls and messages: ⢠The phone must be turned on ⢠A valid SIM card must be inserted ⢠You must be located in the service area of the wireless (GSM) network ⢠The local carrier services must be available and activated to support services like data call, e-mail, fax, WWW , and W AP 7 INTERNET ⢠You can browse the WWW and use WAP services ⢠You can quickly set up Internet and W AP access points MESSAGING ⢠You can send and receive faxes, e-mail, and short messages, as well as view e-mail attachments TELEPHONE ⢠You can make and answer voice calls ⢠You can talk in handsfree mode using the high- quality speakerphone DESK ⢠You can create, edit, and manage links to other applications or third-party software ⢠You can also customize the background image of your Nokia 9290 Communicator CONTACTS ⢠You can manage all your contact data in the same place ⢠You can use the telephone, short messages, fax, and e-mail applications with this information CALENDAR ⢠You can check appointments and special events, list things to do, and set alarms for calendar entries OFFICE ⢠You can view and edit Document and Sheet files, view presentations, as well as organize your files in File manager EXTRAS ⢠You can access the Clock, Unit converter , Calculator , Imaging, Voice recorder, Video player and Control panel functions, as well as add-on applications HELP ⢠You can access the help function from any application MENU ⢠Opens a set of options depending on the application you are in ARROW KEYS ⢠You can scroll up and down, left, right, and diagonally
3. APPLICA TIONS Contents: 3.1 Desk 3.2 Tel 3.3 Messaging 3.3.1 SMS 3.3.2 Mail 3.3.3 Fax 3.4 Internet 3.4.1 WWW 3.4.2 WAP 3.5 Contacts 3.6 Calendar 3.7 Office 3.8 Extras 3.8.1 Control panel 3.9 Other applications 3.9.1 Log 3.9.2 Receive via IR 3.9.3 SyncML - remote synchronization
9 3.1 Desk The Desk application group is used for managing and using various links to your favorite applications or third-party software. Y ou create these links in the relevant applications. Also, quick notes can be written in this application. The Desk application is customizable by the user: ⢠Background image is changeable ⢠Reminder notes can be created quickly ⢠Shortcuts/links can be created to: ⢠Applications ⢠Messages ⢠WWW pages and WAP bookmarks ⢠Documents, Sheets, Notes 3.2 Tel Telephone is the application for call management and adjusting the telephone settings. The main telephone features are listed below . The full GSM telephone feature list can be seen in chapter 2.2. ⢠Make and receive voice calls ⢠Multiple search criteria for the telephone directory ⢠Handsfree option ⢠Sending sequences of dial tones (D TMF) during the active call ⢠Maintain list of DTMFs for quick access ⢠Maintaining phoneâ s speed dial list ⢠Monitoring call costs ⢠Adjusting the phone volume level 3.3 Messaging The Messaging application is a central place for Fax, SMS, and Mail applications. Y ou can write, edit, and send mail, short messages, and faxes in their corresponding editors. ⢠Inbox folder for received messages and faxes ⢠Sent messages folder for sent messages ⢠Drafts folder for messages not yet sent or ready ⢠Outbox folder for messages that are selected to be sent but are not yet sent ⢠New messages note appears in the screen when new fax, e-mail, or short messages arrive ⢠Contact cards can be created from messaging editors/ viewers address fields ⢠Recipient/sender information is compared to contacts database information (entry verifying) 3.3.1 SMS User can write and receive short text messages (SMS). The following SMS features are supported: ⢠Unclassified short messages ⢠Class 0, 1, 2, and 3 short messages ⢠Concatenated short messages (e.g., messages over 160 characters) ⢠Received class 2 short messages (SIM specific) are stored both in the SIM and in the Inbox ⢠Multiple recipients ⢠Send options: Delivery , Date (in scheduled sending), Time (in scheduled sending), Delivery report, Validity period, Reply path request, Service center , Message conversion ⢠Unicode (character) support 3.3.2 Mail User can send and receive e-mail. Mail addressed to you is not automatically received by your Nokia 9290 Communicator , but by your remote mailbox. To read your mail, you must first connect to the remote mailbox and then select the messages you wish to retrieve. The connection is established via a data call. The following features are supported: ⢠Multiple mailboxes, new mailboxes can be added ⢠Carrier or service provider can add new remote mailboxes by smart messages ⢠Disconnected (= offline) mode ⢠Read e-mail attachments: Windows Word, Excel, and P owerPoint. You can view many other file types too, like Lotus files. More file viewers are provided on the CD-ROM supplied in the sales package. ⢠Mail editor with font formatting, alignment adjusting, object inserting, spell checking (installable from CD-ROM, English only) and bulleting features ⢠Sending mail attachments ⢠Opening attachments from mail viewer to appropriate application ⢠Send as mail (attachment) functionality from other applications (menu command) ⢠Send options: Priority , Message type, Copy to self, Request read receipt, Mail account, Send message ⢠Multiple recipients. Recipient fields: To, Cc, Bcc ⢠Special strings (phone numbers, URLs, etc.) are recognized in Mail viewer and can be used for making a call or launching Web application ⢠PCMail for PC synchronization
10 3.3.3 Fax User can read, write, and send fax messages. The Fax editor allows user to write formatted text with embedded objects such as spreadsheet objects. User can also use another editor for writing fax messages. The Fax viewer is used for viewing received faxes (fax images). ⢠Fax ECM (Error Correction Mode) provides automatic resending of pages in case of error ⢠Normal Fax polling (user makes fax call, other end sends fax in the same call to the user â network dependent feature) ⢠Class 2 and 2.0, Group 3 ⢠Transmission speed up to 14.4 kbps ⢠Receive and send resolution ⢠standard 60 x 60 dpi ⢠fine 100 x 1 00 dpi ⢠Fax restriction and fax forwarding ⢠Menu commands for sending written fax also as SMS, mail, or via IR ⢠Cover page templates for easy fax writing and for corporate usage ⢠Fax is a network service 3.4 Internet The Internet application provides access to Internet and value-added services â with Login script and Callback supported. The Main view contains WWW and WAP browser application icons as default. 3.4.1 WWW The Nokia 9290 Communicator has a full-featured W eb browser including: ⢠HTML 3.2 support (including frames support) ⢠HTTP 1.1 ⢠Color WWW pages support ⢠Pointer ⢠Add link bookmark and frame bookmark ⢠Full screen mode ⢠Font style and size can be changed (which show Web page) ⢠Secure W eb browsing (HTTPS) supported over SSLv3 and TLSv1 ⢠WWW browser plug-in support ⢠Caching of Web pages and offline browsing ⢠History lists ⢠Bookmarks ⢠Reload ⢠Find 3.4.2 WAP There are two views in WAP browser: the Bookmarks view and the Card view . The Card view consists of a rendered card and options list. Bookmark view consists of a hierarchical list of saved bookmarks. The main features: ⢠WAP 1.1 ⢠Displaying the encoded WML from the WBXML ⢠Displaying online WBMP images with the WML ⢠Follow the state modals defined in the WML for navigation ⢠Supports WMLScript ⢠Supports color images ⢠Use of the WAP stack for optimal Over the Air (O TA) bandwidth usage ⢠Number of bookmarks supported: 1 00 ⢠Tables supported ⢠Find 3.5 Contacts Use Contacts for creating, editing, and managing all contact information, such as phone numbers and addresses. The main contacts database is in the Nokia 9290 Communicatorâ s memory . Other applications (such as telephone, short messages, fax, and e-mail) use contact information from this application. You can also store contacts in separate databases on an attached memory card. ⢠Several phone numbers per contact/entry supported ⢠Three address fields (Preferred, Business, Private) ⢠Phone call, SMS, or e-mail can be created/sent directly from contact card ⢠Group cards to send short messages, faxes, or e-mails to a large number of people ⢠SIM and Memory Card contacts can be viewed and edited through this application ⢠One-touch dialing, individual ringing tones, and contact images can be assigned to a contact card ⢠General and individual logs ⢠Contacts database can be exported to PC and imported from PC ⢠By using Sync-button on the deskstand, database can be synchronized with the most common PC contacts databases, such as Microsoft Schedule , Microsoft Outlook, Lotus Notes, Lotus Organizer , etc. (More third-party converters can be added later) ⢠vCard compatible
11 Contacts compatibility: ⢠Microsoft Schedule 7.x ⢠Microsoft Outlook 97/98/2000 ⢠Lotus Notes 4.5, 4.6, 5.0 ⢠Lotus Organizer 97, 5.0, 6.0, GS/4.0 ⢠SyncML remote synchronization 3.6 Calendar The Calendar application is used for organizing time usage by storing and viewing information about events and tasks. ⢠Calendar has the following views: Month, Week, Day , Weekly time schedule, Y ear schedule, Anniversaries, and T ask lists ⢠Multiple task lists ⢠Task lists with alarms and priorities ⢠Possibility to have several calendars (e.g., for private and business usage) ⢠Colors and icons can be used to separate different types of calendar events ⢠Calendar events can be sent and received as smart messages ⢠National holidays and other calendar events can be received from WWW as normal calendar files ⢠Calendar can be exported to a compatible PC and imported from a compatible PC ⢠By using Sync-button on the deskstand, calendar data can be synchronized with the most common PC calendars, such as Microsoft Outlook, Schedule , Lotus Notes and Lotus Organizer ⢠Private and public option in calendar event: for example, only public events can be synchronized with PC Calendar compatibility: ⢠Microsoft Schedule 7.x ⢠Microsoft Outlook 97/98/2000 ⢠Lotus Notes 4.5, 4.6, 5.0 ⢠Lotus Organizer 97, 5.0, 6.0, GS/4.0 ⢠SyncML remote synchronization 3.7 Office Office application group contains the following applications: ⢠Document for viewing, creating, and editing documents â Microsoft Word compatible ⢠Spreadsheet for viewing, creating, and editing spread- sheets â Microsoft Excel compatible ⢠Presentation viewer â Microsoft P owerP oint compatible ⢠File Manager for file management 3.8 Extras Extras is an application group for several types of applications, for instance: Clock, Calculator , Games, Imaging application, Control panel, Recorder , Video player , and Unit converter . Also, additional applications can be installed here by using the Nokia 9290 PC Suite for Nokia 9290 Communicator . 3.8.1 Control panel The Control panel application manages all the settings that are not related to one single application. There is also one operational feature in Control panel Main view , namely âÂÂLock system.â Control panel main view contains several icons for different setting categories. Opening them will display a dialog or another view . The settings are: Display Contrast, brightness, color , and screen blanker settings Date & time Present time setting, clock, and agenda alarm snooze times settings Regional settings Time, date, number , and currency formats Internet access The user can edit, make new , and delete Internet connections, which are used in different applications.
12 Profiles Enables the user to control the audio-visual function- ality and accessibility of the device. Each profile is a group of setting values that can be activated at once by activating the profile. One of the profiles is always active. Default profiles are Normal, Silent, Flight, Outdoor , Meeting, Pager , and Car , but the user may add, delete, and modify them as s/he wishes. Security The following settings can be modified: ⢠PIN code request ⢠Autolock period ⢠SIM change security ⢠PIN code ⢠PIN2 code ⢠Lock code ⢠Restriction password Certificate manager Managing of cryptographic keys. For example, SSLcertificate. Install/remove add-on applications It opens a Main view of the Applications Installer . Default folder User can specify the folder that all applications should use as the default folder in the âÂÂSave asâ command. Memory Shows detailed view of device and memory card usage by file type. Accessories Settings for car kit and headset accessories. About product Detailed information about the Nokia 9290 Communicator . Regional settings Date, time, number , and currency preferences. 3.9 Other applications 3.9.1 Log Log application shows communications from and to the device. Application menus (Menu â Tools) have a command for easy access to log application. 3.9.2 Receive via IR Infrared (IR) receiving is possible to activate through application menus or by keyboard shortcuts at any time. Received files or messages end up in the Messaging Inbox. Infrared in general has the following features: ⢠Support IrDA ⢠Support for IrTranP ⢠IrObex 1.1 ⢠Transmission speed up to 1 15 kbps 3.9.3 SyncML â remote synchronization The Nokia 9290 Communicator supports the SyncML syn- chronization of contacts, calendar , and task lists over the GSM data call. Nokia 9290 Communicator will work with SyncML-enabled network applications and services. The Nokia 9290 Communicator Remote synchronization application is supplied on the CD-ROM in the Nokia 9290 Communicator sales package. The Nokia 9290 Communicator works with SyncML-enabled synchronization servers that support PIM data (contacts, calendar , task lists). There will be various vendors bringing SyncML-enabled synchronization servers both for carriers and Internet service providers (synchronizing with Internet calendars) and for the corporate market (synchronizing with Lotus Domino or Microsoft Exchange). The list of products that have passed the conformance and interoperability tests of the SyncML initiative can be found at the SyncML initia- tiveâÂÂs Web site, www .syncml.org . In addition to the contacts, calendar , and task lists, there is a possibility for independent software vendors to build corporate solutions or vertical applications (inventory data synchronization, sales data synchronization, etc.) based on SyncML technology on top of the Symbian operating system in the Nokia 9290 Communicator .
4. PC CONNECTIVITY Contents: 4.1 Nokia 9290 PC Suite for Nokia 9290 Communicator 4.2 Upgrade software 4.3 Multimedia converter 4.4 Nokia 9290 Administrator Suite
4.1 Nokia 9290 PC Suite for Nokia 9290 Communicator Y ou can connect your Nokia 9290 Communicator to a com- patible P C o r laptop using the Nokia 9290 PC Suite for Nokia 9290 Communicator program supplied on the CD-ROM in the Nokia 9290 Communicator sales package. Nokia 9290 P C Suite for Nokia 9290 Communicator works with Windows 95/98/2000 and NT 4.0. The Nokia 9290 PC Suite features are: ⢠File management â Provides access to the Nokia 9290 Communicator file management as well as the userâ s own PC file management to move, copy , rename, and delete files and folders on and between your Nokia 9290 Communicator and your PC. ⢠Task scheduler â Enables the user to specify regular tasks and then automatically manages these for the user . Y ou can synchronize applications data like contacts or e-mails between your Nokia 9290 Communicator and your PC. ⢠Backup/restore â (Archive Manager) enables an easy way to view backed-up files and restore different archived versions. ⢠Control panel â Provides access to all Nokia 9290 PC Suite settings. ⢠Installing applications ⢠Offline mode â Y ou can also use Nokia 9290 PC Suite when it is not connected to your Nokia 9290 Communicator (offline mode). When you connect the two devices the next time, the changed information is updated from your PC to your Nokia 9290 Commu- nicator and vice versa. ⢠Plug-ins ⢠PC upgrade software (section 4.2. below) ⢠Nokia 9290 Administrator Suite (section 4.4 below) ⢠Other additional plug-ins 4.2 Upgrade software The upgrade software is a PC connectivity plug-in. Therefore, you first have to install the Nokia 9290 PC Suite for Nokia 9290 Communicator before installing this program. This upgrade program enables you to move your contact data (phone book), and calendar from the Nokia 51 00, 6 100, 7 100, 8200, 8800 series GSM phones and the Nokia 9 1 10 Communicator to the Nokia 9290 Communicator . The upgrade software is supplied on the CD-ROM of the Nokia 9290 Communicator sales package. 4.3 Multimedia converter With Multimedia converter you can convert common video file formats to NIM format playable on the Nokia 9290 Communicator . When converting a video file, the size of the converted file is usually much smaller than the size of the original file. Y ou can also convert common audio file formats to WAV format and optimize existing WAV format sound files for use on the Nokia 9290 Communicator . Y ou can use converted WA V files as ringing tones, for example. Multimedia converter runs on the 32-bit Microsoft Windows operating system (95, 98, Me, NT4, and 2000). It is included on the CD-ROM of the sales package. Y ou can use the Nokia 9290 PC Suite for Nokia 9290 Communicator to copy converted files to your Nokia 9290 Communicator via a serial cable or an infrared (IR) connec- tion. Y ou can also store video clips directly to a memory card, if you have an appropriate peripheral installed in your com- puter . NIM files can also be stored on a Web server and referred from an HTML page. This enables users to down- load NIM files into the Nokia 9290 Communicator . Multimedia converter supports most files that you can play in Windows Media Player . The exact set of supported files depends on the version of Media Player installed in your system and on the installed audio and video codecs. Typically , Multimedia converter is able to support most AVI, W AV , MPG, and MP3 files. Note: Y ou can play a NIM file on your PC using Multimedia converter only . 4.4 Nokia 9290 Administrator Suite Nokia 9290 Administrator Suite is an additional PC software that is targeted to retailers and corporate IT personnel. It features Nokia 9290 Communicator setting, file, and appli- cation delivery to the Nokia 9290 Communicator . The Nokia 9290 Administrator Suite is supplied on the CD-ROM in the Nokia 9290 Communicator sales package. It is possible to transfer the configurations to the Nokia 9290 Communicator either by connecting the Nokia 9290 Communicator to the PC where the Nokia 9290 Administrator Suite is locally or remotely . In the user interface of the Nokia 9290 Administrator Suite it is possible to create a whole selection of different settings, applications, etc. and transfer that set to one or several Nokia 9290 Communicators. This makes it possible to easily administer several Nokia 9290 Communicators from one service point. The following settings can be configured: ⢠IAP settings ⢠E-mail settings ⢠WAP settings ⢠SMS settings It is also possible to transfer/install: ⢠WWW bookmarks ⢠WAP bookmarks ⢠Voice and fax mailbox numbers ⢠Files ⢠Applications/software In short, the Nokia 9290 Administrator Suite will help company administrators to offer a standard Nokia 9290 Communicator software and setting package to their users. 14
5. NOKIA 9290 COMMUNICA T OR AND DA T A SERVICES Contents: 5.1 Introduction 5.2 Data call and high-speed data options
5.1 Introduction Before you can start to use the Nokia 9290 Communicator data features efficiently , you have to check the following information from your GSM carrier: ⢠The cellular network that you use must support data calls ⢠Data service must be activated for your SIM card ⢠Before you can use HSCSD data, check with your carrier to see whether it is supported 5.2 Data call and high-speed data options Data call options can be handled in Internet settings. Under Advanced settings; Connection type, Remote modem type and other data call related information could be found and edited. Connection type gives two alternatives for the connection type. The default for every IAP (Internet Access Point) is âÂÂNormal,â which stands for normal single time slot GSM data call. The connection speed can be either 9600 or 14400 bps, and in addition for analog calls autobauding is the third speed option. âÂÂHigh speedâ selects the High Speed Circuit Switched Data (HSCSD) call. Higher transfer speeds are achieved by reserving multiple GSM time slots for single user . Note: The 14400 bps speed for normal GSM data call and HSCSD services are not basic GSM data services. These services may not be available in all networks in all areas , and they may require a separate subscription. If the network does not support the call type, or it has not been enabled in the userâ s subscription, the data call may fail. Even the basic data call services may need to be subscribed to separately . Remote modem type defines the connection method to be used. There are three alternatives available: Analog (for normal modems), ISDN V.1 10, and ISDN V.120. The GSM network and the remote access server or dial-in modem pool must support the selected connection method; other- wise, the connection attempt will fail. Note: Analog (normal modem) connections are usually supported in all networks. The connection time (before the data call is established) is about 40 seconds for analog connections and 15 seconds for ISDN connections 1 . Maximum data speeds are 28800 bps for analog, 38400 bps downstream for V.1 1 0 and 43200 bps downstream with V.120. In addition, the data flow may be smoother when using ISDN connections. These restrictions are caused by the GSM network, and are not inherent to the Nokia 9290 Communicator . Max. connection speed is for determining the maximum connection speed. The GSM network may change the current connection speed at its direction â for example, when the network becomes congested. Note: All HSCSD connections are always made with 14400 bps per timeslot. This speed is almost always available in the areas where network coverage is good and the network supports HSCSD. If the network signal quality gets weaker , the speed is automatically do wngraded to 9600 bps per timeslot by the GSM network. The network can also decrease the number of time slots allocated for a user if network congestion occurs. These actions may cause fluctuations in the data rate, and may cause the total data rate to be smaller than the requested data rate. 1 These times are rough estimates and depend on the network coverage, on the Internet service provider , and other variables. 16 When HSCSD connections are used, the user may control how many timeslots are used for the connection. Some GSM carriers may charge on slot amount usage basis; some other GSM carriers may implement a fixed charging model for HSCSD calls. Please contact your network carrier for HSCSD coverage and charging details. Connection type Remote modem type 1 timeslot 2 timeslots 3 timeslots Normal data call Analog Autobauding, Not available Not available 9600 or 14400 ISDN V.1 10 9600 or 14400 Not available Not available ISDN V.120 9600 or 14400 Not available Not available High-speed data call Analog 9600 or 14400 19200 or 28800 Not available ISDN V.1 10 9600 or 14400 19200 or 28800 28800 or 38400 ISDN V.120 9600 or 14400 19200 or 28800 28800 or 43200 Available connection speeds are:
6. NOKIA 9290 COMMUNICA T OR AND INTERNET SERVICE Contents: 6.1 Introduction 6.2 Nokia 9290 Communicator and Internet features 6.3 Creating Internet connections 6.4 Connection details 6.5 Advanced settings 6.5.1 Setting proxies 6.5.2 Modifying data call settings 6.5.3 Taking callback into use 6.5.4 Other settings 6.5.5 Setting script options 6.5.6 Setting server address options 6.6 Editing Internet access 6.7 Tested Nokia 9290 Communicator compatible PPP access servers 6.8 Default parameters and settings
6.1 Introduction This chapter describes how to configure Internet settings manually to the Nokia 9290 Communicator to be able to access the Internet. Information concerning the correct settings must be obtained from the Internet service provider (ISP). The service provider may be able to configure the access point for you via a special SMS message or a WWW page, which sets all the necessary Internet access settings. Please contact your Internet service provider (ISP) for details. For more information about using the Internet application, please refer to the User Guide of the Nokia 9290 Communicator . 6.2 Nokia 9290 Communicator and Internet features The Nokia 9290 Communicator supports the following basic Internet features: ⢠Normal single-slot GSM data calls using either 9600 bps or 14400 bps ⢠Support for analog modem connections and ISDN V.1 1 0 and ISDN V.120 rate adaption protocols ⢠Point to P oint Protocol as the data link level protocol, RFC 166 1 ⢠PPP link level authentication using the Password Authentication Protocol (PAP) or Challenge Authentication Protocol (CHAP), RFC 1334 ⢠PPP link level compression using Stac LZS (modes 4 and 3), MPPC, and Predictor compression methods, RFC 1974 ⢠PPP callback using the Microsoft callback protocol (client supplied number , server supplied number) and PPP callback type 0 as specified in RFC 1570 ⢠Internet Protocol Control Protocol (IPCP) extensions for Domain Name Service (DNS) ⢠Scripting language for automating login procedures, compatible with previous Symbian OS devices (such as PsionâÂÂs Series 5 PDAs) ⢠Van Jacobson TCP/IP header compression, RFC 1 144 ⢠Secure Sockets Layer (SSL) version 3 and T ransport Layer Security (TLS) version 1 protocols To obtain access to the Internet: ⢠The cellular network (GSM 1900) you use must support data calls ⢠The data service (also the High-speed (HSCSD) service if used) must be activated for your SIM card ⢠You must have obtained an Internet Access Point (IAP) from an Internet service provider ⢠You must have entered the proper Internet settings 6.3 Creating Internet connections Obligatory settings for Internet connection are (information from Internet service provider): ⢠Phone number where to call ⢠Username ⢠Password ⢠Data call options (especially when HSCSD data is used) To set up new Internet access: 1. Open Internet startup from Desk or from under Extras. 2. Select Internet access and press Open. 3. T o create an Internet connection, press New . If you want to modify an existing Internet Access P oint, open Internet access from Control panel in the Extras application. 6.4 Connection details 1. Open Control panel from Extras. 2. Select Internet access and press Open. 3. T o view and edit existing Internet connections, select the IAP you want by pressing Change. T o create a new Internet Access Point, press New . 4. Create a Connection name that you can recognize easily (e.g., name of the ISP). 5. Type in the phone number of your Internet account. This is the phone number of the dial-in line (also called the modem pool or PPP servers) of the ISP . Y our ISP may have several different phone numbers for different modems. 6. Set Password prompt to Y es if you want to type in your password every time you log in. Select No to save your password in your Nokia 9290 Communicator and auto- mate the login procedure. If you are using one-time passwords (such as RSA SecurID or OTP), select Y es. 7. T ype in the Username for your Internet account. 8. T ype in the Password for your Internet account. Then confirm the password by retyping it in the Confirm password field. Note that the characters in your password are replaced with symbols so that no one can see them accidentally . Note also that usernames and passwords are usually case-sensitive (capitalization of letters matters). The username and password are used for PPP (Point to P oint Protocol) authentication and supplied to you by your Internet service provider . Some IAPs do not require the username and password; some IAPs may only require the phone number and the connection name. 18
6.5 Advanced settings To define advanced settings of the connection, press Advanced settings. A dialog with four pages opens. 6.5.1 Setting proxies Y ou may wish to use a proxy to speed up access to the Internet. Note also that some ISPs require the use of WWW proxies; contact your ISP to determine the proxy details. Y ou may also need a proxy server when you have an Internet connection for your companyâ s intranet, and as a result are unable to retrieve W eb pages from the WWW . In this situa- tion you may need to set up a proxy server to retrieve W eb pages outside your companyâ s intranet. A proxy is a server at the interface between your Nokia 9290 Communicator and the remote (target) WWW server that offers the W eb pages. Proxies usually cache popular documents so that they do not need to be reloaded from the remote server every time they are accessed. After you get the connections working, you may want to test the connection speed with and without proxies to find out whether they offer any increase in speed. 1. Select the Protocol for your connection. (HTTP is for normal WWW connections and HTTPS is for SSL-secured WWW connections. Usually , but not always, the proxy information is the same for both protocols.) 2. Set Use proxy server into Yes or No according to your setting requirements. 3. T ype in the P ort number . This is often 8000, 8080, or 80, but can vary by proxy server . 4. T ype in the address of the Proxy server (either the domain name or the IP address). 5. T ype domains that should not be accessed through the proxy server in the No proxy for field. Separate each domain with a semicolon (;). For example, if you want to use proxies for all pages other than those that reside in your companyâ s intranet, write your companyâ s domain name (e.g., yourcompany .com) in this field. If your com- pany intranet requires the use of proxy servers, contact your support person for details. Note: Settings 3, 4, and 5 are available only when proxy servers are used. 6.5.2 Modifying data call settings 1. T o activate the Data call tab, press the Menu key . 2. Select the Connection type. Options are Normal and High speed. Note: T o be able to use High speed, the network service provider has to support this feature, and, if necessary , to activate it for your SIM card. When using High speed, extra charges may apply , even for received data calls within your home network. Check with your network service pro vider for details on their pricing. 3. Select the Remote modem type. The default is Analog, but your service provider may also have ISDN connections available. This setting may depend on both your GSM network carrier and ISP , because some GSM networks do not support certain types of ISDN connections. For details, contact your ISP and network provider . ISDN connec- tions are preferable to analog connections, because they offer considerably faster data call establishment (often about twenty seconds faster than with analog connections), and offer higher data transfer speeds as the connection is fully digital from end to end. On the other hand, if you have problems establishing a data call (for example, when roaming outside your home net- work), using analog connections may help you to estab- lish a connection. 4. Set the Maximum connection speed. When your Connec- tion type is Normal, only autobauding, 9600, and 14400 are available. Different, higher connection speeds are available with different combinations of High speed settings. Higher data rates may cost more, depending on the network service provider . The speed indicated here is the maximum speed that will be used. The true data transfer speed depends on congestion in the Internet, the type of data you are downloading, whether you are run- ning other applications on the Nokia 9290 Communicator , on the congestion of the mobile phone network, and on your location in the mobile phone network. In poor reception areas, the network may choose to use a sig- nificantly lower transmission speed. 5. T ype in the Modem initialization string, if needed, to control the Nokia 9290 Communicator using modem A T commands. Enter characters specified by your network service provider or ISP; otherwise, leave this field empty . The modem initialization string specified here will override all other data call settings. The initialization string may be required if the normal settings are not sufficient for a particularly complex network/IAP configuration. For more details, see also Chapter 5 â Nokia 9290 Commu- nicator and Data Services. 19
6.5.3 Taking callback into use This option allows a server to call you back once you have made the initial call, which means in most countries that a connection is established without your having to pay for the call. Contact your ISP to find out whether this service is available and to subscribe to this service. If you are roaming outside your home network or use high-speed data calls, you may still have to pay for part of the call. Note: Most public ISPs do not support callback. Most common callback users are companies and other private dial-up systems that require increased security . 1. T o activate the Callback tab , press the Menu key . 2. Set Use callback to Y es if you have a service that dials back to your phone when you establish an Internet connec- tion. Callback works as follows: Y ou first dial into the IAP and request callback. The data call is then closed. Within a minute, the IAP has to call back to your Nokia 9290 Communicator . 3. Select the Callback type. Y ou have the option of choosing between IETF PPP callback protocol, which calls back to a number stored on the callback server , and two different modes of Microsoft callback protocol, one of which uses a number stored on the server , and one which uses a client-supplied phone number . 4. If you selected Use number below , type in your Callback number . This number is usually the data call phone number (not the voice number) of your Nokia 9290 Communicator . This is filled in when using Microsoft cal lba ck protocol in a mode where the client specifies the number to call back. The Callback call from the remote server must use the same data call settings as the callback-requesting call. The network has to support the call type in both directions (to and from the Nokia 9290 Communicator). You may need to ask your ISP to configure the callback server accordingly , and check with your network provider as to whether the GSM network supports this functionality . 6.5.4 Other settings 1. To activate the Other tab , press the Menu key . 2. Set Allow plain-text login to No if you donâÂÂt want to send your password as plain text without encryption. Note that this option only affects PPP connections, and some ISPs require that this setting is Y es. Check with your ISP: If your ISP supports CHAP or MS-CHAP , set this to No; if they only support P AP , set this to Y es. 3. Set Use PPP compression to Yes to enable compression. When set to Y es, this option speeds up the data transfer (especially when downloading text and other compressible information) if it is supported by the remote PPP server . If you have problems establishing a connection, try setting this to No. 6.5.5 Setting script options If you need to define script options for your Internet con- nections, move to the Other page of the Advanced settings dialog, then press Script options. A script can automate the connection between the Nokia 9290 Communicator and the server . Note: Scripts are not usually required when you establish a connection. T o find out whether you need a script, contact your ISP . Usually a script is required if the login procedures do not use standard PPP authentication systems (P AP , CHAP , or MS-CHAP). 1. Press Script options to open the Script options dialog. 2. Set Use login script to Yes in case your Internet service provider requires a login script, or if you want to automate your login with a script yourself. 3. Set Display terminal window to Yes if you want to be able to see the execution of the script or to interact with the terminal server during login. Note that this setting is only available when Use login script is set to Y es. 4. T o view and modify the script, press Edit script. 5. T ype in the script. This information is provided by your Internet provider . Press Import script to import script from a file. The scripting syntax is available from Forum Nokia and has to be imported in Unicode format. 6. Press Done to finish. 7. Press Done to close script options. 20
6.5.6 Setting server address options Note: Usually you do not have to alter A ddress options. Most ISPs support automatic configuration of IP and DNS addresses. 1. Press Address options to open the server address options dialog. 2. In the Address options dialog, you can set the addresses of your Internet services. IP addresses are unique strings of numbers that point to computers on the network. Set Auto retrieve IP address to Y es if you want to obtain the IP addresses automatically from the server (this is also called the dynamic IP). To type in the IP addresses on the fields below , select No. T ype in your IP address if Auto retrieve IP address is set to No. In this case, your ISP will provide you with a fixed IP address. 3. If you cannot auto retrieve DNS addresses automatically , set Auto retrieve DNS address to No, and type in the Primary DNS address and the Secondary DNS address if necessary . DNS means âÂÂdomain name serverâ â that is, a server that translates domain names (foo.bar .com) into IP addresses (of the type 000.000.000.000). 4. Press Done to close the Address options dialog. 5. Press Done to close the Advanced settings dialog. 6. Press Done to close the Connection details dialog. Note: New connection is set as Preferred connection by default. T o select a different Preferred connection, press Change. A list of your Internet connections opens. 6.6 Editing Internet access To edit some additional settings of already configured Internet access points, press the Menu key and open the Control panel under T ools (or open it from Extras). Open Internet access. In addition to the settings discussed above, you can also edit the following settings: ⢠Preferred connection: If you have configured several Internet access points, select which one is the preferred one when connecting to the Internet. ⢠If idle, stay online: The connection to the Internet will automatically close after the inactivity period defined here. The options are For 2 minutes/For 5 minutes/ For 1 0 minutes/For 60 minutes. ⢠Ask before connecting: To monitor the connection process, set this setting to Y es. This way you can always see when a connection is established as the connection dialog opens when you use the W eb browser . If you are using several different IAPs (for example, one for company intranet and one for public WWW access, or one for normal and one for high- speed data calls), it is recommended to set this to Y es so that you can always be sure to which IAP the connection will be made. Press Done to close the Connection details dialog. 6.7 Tested Nokia 9290 Communicator compatible PPP access servers This section contains a list of commonly used PPP dial-in access servers, which have been compatibility tested with the Nokia 9290 Communicator . Another type of PPP server may also work, assuming the server has been configured with generally used PPP settings, such as: ⢠The PPP server is capable of establishing data calls using the PSTN/ISDN V.1 10/ISDN V.120 method ⢠The server is able to handle a maximum transfer unit (MTU) of at least 1500 octets ⢠Login script authentication with terminal server or PAP/CHAP authentication with PPP server ⢠Van Jacobson TCP/IP header compression on/off ⢠Dynamically/manually set IP and DNS addresses ⢠PPP compression provided by Compression Control Protocol on/off ⢠IP packet routing gateway information is set by the PPP server The configuration options listed here may differ for your local Internet access point. Please contact your local ISP or corporate information management to get more information about used parameters for your Internet Access P oint. 21
Compatibility tested PPP servers with the Nokia 9290 Communicator: Cisco AS5300 Cisco AS5200 Shiva Access Switch Shiva LanRover E Microsoft NT RAS 4.0 Ericsson Tigris AXC 623 Ascend Max 4004 Lucent P ortMaster 3 Nortel/Bay Networks Versalar 8000 Morning Star PPPD Various Linux/Unix based PPP daemons conforming RFC 166 1 6.8 Default parameters and settings ⢠Async Control Character Map (ACCM) 0x00000000 ⢠Dynamic protocol timeout for LCP , IPCP , CCP , P AP , and CHAP 3 seconds ⢠Maximum Receive Unit (MRU) 1500 ⢠Magic number negotiation is on ⢠Address and Control field Compression is on ⢠Maximum configure request restart 1 0 ⢠Maximum configure Naks before failure 5 ⢠Link quality report interval 1 0 seconds ⢠Compression method negotiation order (PPP compression on by default): ⢠Stac LZS mode 3 ⢠Stac LZS mode 4 ⢠Microsoft PPC ⢠Predictor 1 ⢠PPP callback is off ⢠TCP/IP-header Van Jacobson compression on ⢠TCP maximum segment size (MSS) 536 bytes ⢠Maximum time-to-live (TTL) 64 ⢠Default PPP idle timeout is 2 minutes ⢠Show connection dialog is off ⢠Proxy servers are off by default ⢠Default data call parameters are normal analog data- calls, autobauding, and no AT commands ⢠Plain text login is allowed by default ⢠Login scripts are not used by default ⢠IP addresses and DNS addresses are requested dynami- cally from server by default ⢠For SSL and TLS, a collection of well-known certification authoritiesâ root certificates has been installed and marked as trusted 22
7. NOKIA 9290 COMMUNICA T OR AND E-MAIL SERVICE Contents: 7.1 Introduction 7.2 Mail settings 7.3 General page 7.4 Servers page 7.5 Retrieve 7.6 Advanced page 7.7 PCmail and Nokia 9290 Communicator 7.8 Compatible e-mail systems 7.9 Supported e-mail attachments 7.1 0 RFC (Request for Comments) documents
7.1 Introduction For reading and sending e-mail via the Nokia 9290 Commu- nicator remote e-mail client, you need to have an Internet Access P oint (IAP) configured to your Nokia 9290 Commu- nicator . For further information on how to configure IAPs, please refer to Chapter 6 â Nokia 9290 Communicator and Internet Service. Y ou also need to have an e-mail account that supports SMTP protocol for sending e-mail, and POP3 or IMAP4rev1 protocol for receiving e-mail. You can also have multiple e-mail accounts in the Nokia 9290 Communicator . Note: The necessary settings for mail configuration are provided by your e-mail service provider . Depending on your service pro vider , you may not need to fill in all of the settings. If your mail settings are incomplete or incorrect, please contact your service provider . An e-mail service provider can be your company or a commercial ISP , for example. Important information that must be filled in when defining a new e-mail account includes: ⢠Host name to receive mail (IMAP4 or POP3 e-mail server) ⢠Host name to send mail (SMTP server) ⢠Mailbox type (which protocol to use, either POP3 or IMAP4) ⢠Username (case sensitive) ⢠Password (case sensitive, displayed using asterisks (*)) ⢠Dial-in access point for the mail service ⢠Use of secure connection (i.e., require SSL/TLS encryption to be used) 7.2 Mail settings In order to connect to your electronic mailbox service, yo u need to define your remote mailbox on your Nokia 9290 Communicator . This can be made from the Messaging application main view under Menu (see figure below) or from that shortcut (Internet Start up) in the Desk application. To define a new remote mailbox: 1. Press the Menu key in the main view of the Messaging center and first select Tools, then Accounts. A list of accounts opens. 2. Press Create new to create an e-mail account. Y ouâÂÂll get the following dialog: 3. Select Email and press OK. A dialog with four pages opens. 4. Define the settings on the General, Servers, Retrieve, and Advanced pages below . 5. Y ou must fill in at least: ⢠Username used to log in the POP3/IMAP4 e-mail server ⢠Password for the POP3/IMAP4 e-mail server ⢠Y our e-mail address (e.g., for replies to messages you have sent) ⢠Outgoing e-mail server (host name for SMTP server) ⢠Incoming e-mail server (host name for IMAP4 or POP3 server) 6. Press Delete to discard any changes. 7. Press Close to accept the changes you have made. 7.3 General page 1. Enter the name of the remote mailbox under My account name. The name can be entered freely (e.g., My mail, Johnâ s mail, etc.). 2. T ype your name (note: your name appears here auto- matically if you have entered your contact card), username, and password. Tip: Usually the name and password are the same ones you use for your Internet Access P oint (PPP authentication). However , if your e-mail service pro vider is different from the Internet service provider , this may not be the case. Note that both the username and password are case-sensitive (capitalization of letters matters). If you do not specify a password, you will be prompted for one when you try to read mail in your remote mailbox. 3. My mail address: Type in the e-mail address given to you by your service provider . The address must contain the @ character . This address will be shown as the originating (From) address in your messages. 4. Choose the Internet Access P oint used for the mailbox. Choose from the list that contains all available IAPs. Note that you must be able to connect to the remote mailbox via the given IAP . For example, if you are accessing your companyâÂÂs intranet mailbox, you may need to use your companyâÂÂs intranet Internet Access P oint as well. 5. Choose Default account from the list, which contains all available mail accounts. 24
7.4 Servers page 1. Press the Menu key to activate the Servers tab . 2. Select Mail account type (POP3 or IMAP4). This defines the mail protocol your mailbox service provider recom- mends. If you are allowed to choose between these two protocols, you should select IMAP if you are working with multiple folders and receive a lot of attachments, and POP if you have a single incoming mail folder and receive no attachments. POP may be slightly faster in some situations, but IMAP gives the user more control over the mailbox and mail retrieval. Note that mailbox type cannot be changed after the e-mail account set- tings have been saved! 3. Enter the Outgoing mail server IP address or host name. This is also known as the SMTP server , sending server , or mail relay . When you are sending e-mail, your Nokia 9290 Communicator connects to this server and sends the mail. This server will then relay the mail towards the recipientâ s mail server (e.g. 123.123.123.123 or mail.server .com). 4. Enter the Incoming mail server IP address or host name. This is also known as the IMAP or POP server (depending on the account type) or the remote mailbox server . When you receive mail, the mail will be stored on this server . During mail retrieval, your Nokia 9290 Communicator connects to this server in order to download mail. 7.5 Retrieve Press the Menu key to activate the Retrieve tab and fill in the following settings: ⢠Retrieve: Choose what will be fetched from the remote mailbox when the connection is established. The options are: Message headers (stay online)/Messages and attachments/Messages. The last option is available only if the Mail account type is IMAP4. ⢠Max. size of message: The maximum size of a message that will be retrieved with the Retrieve mail command. The minimum is 1 and the maximum is 1000 kB (kilobytes). One kilobyte corresponds to approximately half of a written page of plain text. Max. size of message also includes attachments. ⢠Synchronize: Sync your mail folders. 7.6 Advanced page Press the Menu key to activate the Advanced tab and fill in the following settings if necessary . Contact your e-mail service provider for the correct settings. ⢠Default mail type: Select the type of mail that you can write and send from your Nokia 9290 Communicator . The options are Plain text/Plain text (no MIME)/ Formatted text (HTML). ⢠If you are using accented characters, you should use either Plain text or Formatted text. Otherwise, accented characters will not be transferred correctly . ⢠For the best compatibility across existing electronic mail systems, choose Plain text. If you are only com- municating with people with new , graphical e-mail systems, you can choose Formatted text. Formatted text may not be correctly shown to recipients with older , text-based e-mail systems. ⢠Use Plain text (no MIME) only if corresponding with people with old e-mail systems. ⢠Send mail: Choose how mail messages are sent from your Nokia 9290 Communicator . The options are Imme- diately/ During next connection/Upon request. ⢠Bear in mind that if you select During next connection, the mail will be sent during the next connection to that mailserver , not during the next connection to the Internet. ⢠Include signature: Select whether your signature is attached to sent mail. The options are No/Use my contact card/Custom. If you choose Custom, press Edit signature to create a signature. ⢠Request read report: Select whether you want to receive a report when the recipient has read your mail. The options are Y es/No. ⢠Not all e-mail software can generate a read report. A read report should not be used as proof that a mail has been read or not read. Usually the recipient can decide whether a read report will be generated or not. ⢠Some mail systems call read reports âÂÂread receiptsâ or âÂÂdisposition notifications. â â¢ Allow report requests: This option defines whether the Nokia 9290 Communicator will generate a âÂÂread reportâ mail to the Outbox if received mail requires it. The options are Y es/No. ⢠Read reports will be generated in your outbox. The Nokia 9290 Communicator will reply to standard disposition notification requests and some non- standard requests. Depending on the senderâÂÂs mail system, a read report may not be generated. If the senderâÂÂs mail system does not support standard disposition notifications, the mail system may not be capable of utilizing the information in the read report automatically . ⢠Copy to my mail address: Select whether you want to send a copy of sent mail to your own mail address. The options are Y es/No. 25
⢠Secure login (APOP): The options are Yes/No. Use of APOP increases security when connecting to a POP3 mail server . Please check with your e-mail service provider whether this option can be used. The option is available only if the used e-mail protocol is POP3. ⢠Note that this does not encrypt your mail or protect the mail itself in any way . This option just protects your password from being transmitted as plain text. ⢠Secure connection (TLS): Select whether to use TLS security when connecting to the mail server . The options are Yes/No. Please check with your e-mail service provider whether this option can be used. ⢠The mail server needs to support the standard âÂÂstarttlsâ or âÂÂstlsâ command (depending on the protocol) in order to be used with the Nokia 9290 Communi- cator . Som e older servers use a dedicated server port for secure connections over SSL. The Nokia 9290 Communicator does not support this non-standard system. ⢠Note that this only protects the transfer of your e-mail between the Nokia 9290 Communicator and the first server (either the sending server or your remote mailbox). When sending mail, it will be trans- ferred without any security from the first mail server onwards. Also, any mail you receive will have been transferred without any security to the remote mail server . ⢠When using security , both the sending and receiving servers must support secure connections. ⢠Enter IMAP4 folder path: (The folder path could be Inbox, for example.) This option is available only if the mailbox type is IMAP4. After you have filled in all details, press Close to close dialogs, and the new e-mail account will appear in the Messaging application as shown in the picture below . (The name of the remote mailbox is the name that you defined earlier .) New e-mail account in Messaging application Now you are ready to use the Retrieve mail command to connect to the newly defined e-mail account and fetch mes- sages. The very first time you connect to the IMAP4 account may take more time, depending on the number of mail messages in the remote Inbox and also the number of remote mail folders, because the device fetches message headers and scans remote folders for subscriptions. Subsequent Retrieve mail commands should work faster , as only changed folder data is downloaded to the device. Note: Once you have retrieved mail and you go offline, all the headers from your remote mailbox are sho wn in your Nokia 9290 CommunicatorâÂÂs Mail inbox. BE CAREFUL WHEN DELETING THEM, because if you delete them, they will be deleted from your Remote inbox, too, the next time you connect to your mailbox. T o avoid this situation, please refer to the Messaging chapter in the User Guide. Tip: When using an Internet Access P oint that uses a high- speed data call, and when you have to send large attachments or e-mails , you will get the fastest upload (sending) speed if you select âÂÂ28800â as the maximum transfer rate in the IAP settings. This involves the use of two GSM timeslots (28800 bits per second) in the uplink direction (from your Nokia 9290 Communicator to the mail server). All other transfer rates use just one GSM timeslot, 9600 or 14400 bits per second, in uplink direction. When downloading (receiving) mail, you will get the best performance by selecting the largest possible value as the maximum transfer rate. 7.7 PCmail and Nokia 9290 Communicator PCmail is a mail you can read, write, and edit on your Nokia 9290 Communicator , but which cannot be sent without your PC or laptop. PCmails are sent the next time you synchronize your Nokia 9290 Communicator to your PC or laptop. Internet mails can be converted to PCmails so that mails can be synchronized with your PC or laptop, or PCmails can be converted to Internet mails so that mails can be sent directly from the Nokia 9290 Communicator . Note: Refer to the Nokia 9290 Communicator User Guide for converting mails. 7.8 Compatible e-mail systems Here are listed mail systems that can be connected with the Nokia 9290 Communicator . All of these systems should work with the Nokia 9290 Communicator . This list is not exhaus- tive and other mail servers supporting standard Internet protocols (SMTP , IMAP4, and POP3) should work as well. Cyrus IMAPD Mail Server (http://asg.web .cmu.edu/cyrus/ ) ⢠Cyrus IMAPD Mail Server (Carnegie Mellon) supports MIME, IMAP4, and POP3 standards HP OpenMail (http://www .hp.com ) ⢠OpenMail 6.0 (for Linux) supports SMTP , MIME, IMAP4, and POP3 standards Lotus Domino Mail (http://www .lotus.com ) ⢠Lotus Domino R5 Mail Server supports SMTP , MIME, IMAP4, and POP3 standards Microsoft Exchange 5.5 (http://www .microsoft.com ) ⢠Microsoft Exchange 5.5 supports SMTP , MIME, IMAP4, and POP3 standards Microsoft Exchange 2000 (http://www .microsoft.com ) ⢠Microsoft Exchange 2000 supports SMTP , MIME, IMAP4, and POP3 standards Oracle InterOffice Mail Server (http://www .oracle.com) ⢠Oracle InterOffice Mail Server 5.1 supports the SMTP , MIME, IMAP4, and POP3 standards 26
Stalker CommuniGate Pro Mail Server (http://www .stalker .com/CommuniGatePro ) ⢠Stalker CommuniGate Pro 3.3 supports SMTP , MIME, IMAP4, and POP3 standards and also secure connec- tions (SSL/TLS). Also APOP command is supported for POP3. Sun Internet Mail Server (http://iplanet.com/ ) ⢠Sun Internet Mail Server 4.0 supports SMTP , MIME, POP3, and IMAP4 standards University of Washington IMAP4 Server (http://www .washington.edu/imap ) ⢠UW IMAP Server v1 0.173 supports POP3 and IMAP4 standards Zmailer (http://www .zmailer .org/ ) ⢠ZMailer (version 2.99) supports SMTP standard TeamW are Office Mail Server (http://www .teamware.com/products/ ) ⢠SMTP , MIME, POP3, and IMAP4 standards Other solutions If the e-mail server does not support POP3/IMAP4 and SMTP protocols, it may be possible to use converter software that provides necessary POP3/IMAP4 and SMTP protocol support for the e-mail server . Examples of converter software include Infinite InterChange by Infinite Technologies. Infinite InterChange creates POP3, IMAP4, and HTTP/HTML support. More information on the Infinite InterChange can be found at www .ihub .com . Additionally , connection to the e-mail server can also be established with the Nokia 9290 CommunicatorâÂÂs Web browser if the e-mail server supports HTTP/HTML access. Note: With the Nokia 9290 Communicator , you can also read W eb mails, i.e. Hotmail and Y ahoo mail. 27 7.9 Supported e-mail attachments E-mail attachments are supported and downloaded attachments that can be viewed on the Nokia 9290 Communicator . Initially supported attachment types are marked with an asterisk (*) in Table 1 (on the next page). Other attachment types in Table 1 are supported if the appropriate application or converter is installed to the device. New attachment types can be supported via add-on applications installed to the Nokia 9290 Communicator . Downloaded attachments can also be saved to files and transferred to a PC for viewing. Overall use of attachments is rather limited by the small disk space and amount of free memory . A memory card can be used to expand the available disk space for messaging. 7.1 0 RFC (Request for Comments) documents Internet e-mail protocols are specified using RFC (Request for Comments) documents. RFC documents are available, for example, from IETF (the Internet Engineering Task Force, www .ietf.org/ ). SMTP (Simple Mail T ransfer Protocol) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RFC 82 1 Standard for the format of ARPA Internet text messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RFC 822 POP3 (P ost Office Protocol, version 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RFC 1939 PPP (P oint to Point Protocol) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RFC 166 1 MIME (Multipurpose Internet Mail Extensions) P art One: Format of Internet Message Bodies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RFC 2045 MIME (Multipurpose Internet Mail Extensions) P art Two: Media T ypes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RFC 2046 MIME (Multipurpose Internet Mail Extensions) P art Three: Message Header Extensions for Non-ASCII Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RFC 2047 IMAP4 (Internet Message Access Protocol, version 4rev1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RFC 2060 TLS (T ransport Layer Security Protocol, version 1.0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RFC 2246 Read receipts (an Extensible Message Format for Message Disposition Notifications, Disposition-Notification-T o header) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RFC 2298 SMTP Service Extension for Secure SMTP over TLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RFC 2487 Using TLS with IMAP , POP3, and ACAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RFC 2595
28 Attachment type File extensions MIME T ypes Audio File WA V, AU, WVE âÂÂaudio/x-wavâ â audio/basicâ â audio/x-sibo-wveâ CompuServe GIF GIF âÂÂimage/gifâ Computer Graphics Metafile CGM âÂÂimage/cgmâ âÂÂimage/x-cgmâ Corel/Novell Presentations SHW âÂÂimage/x-presentationsâ Symbian OS Word* - Symbian OS Sheet* - Symbian OS Bitmap* MBM Internet HyperT ext Markup Language* HTML, HTM âÂÂtext/htmlâ Lotus 1-2-3 WQ1, WKU, WK1, WK3, â application/x-lotus-123â v .1/2/3/4/5/97/Millennium WK4, WK5, WK6, 123 â application/vnd.lotus-1-2-3â Lotus AMI Draw SDW âÂÂimage/x-amidrawâ Microsoft Excel XLS, XLC â application/x-msexcelâ 2/3/4/5/7/97/98/2000 â application/x-excelâ â application/vnd.ms-excelâ â application/msexcelâ â application/xlcâ Microsoft P owerPoint PPT , POT , PPS â application/x-mspowerpointâ 3/4/7/97/98/2000 â application/vnd.ms-powerpointâ â application/pptâ â application/potâ â application/ppsâ â application/mspowerpointâ Microsoft Project MPP â application/vnd.ms-projectâ Microsoft W ord DOC, WRI â application/mswordâ 1/2/3/4/5/6/7/97/98/2000 â application/vnd.ms-wordâ â application/vnd.mswordâ P aintbrush PCX, DCX âÂÂimage/x-pc-paintbrushâ PKZIP Format ZIP â application/zipâ P ortable Network Graphics PNG âÂÂimage/pngâ âÂÂimage/x-pngâ Rich T ext Format RTF â application/rtfâ Ringing T ones* MG â application/vnd.nokia.ringing-toneâ Tagged Image File Format (TIFF , JPEG) TIF , JPG, JIF âÂÂimage/tiffâ âÂÂimage/jpegâ Text* TXT âÂÂtext/plainâ vCard VCF âÂÂtext/x-vcardâ vCalendar VCS âÂÂtext/x-vcalendarâ Visio VSD â application/vnd.visioâ Windows Bitmap BMP , RLE, ICO , CUR âÂÂimage/x-win-bitmapâ âÂÂimage/x-MS-bmpâ âÂÂimage/bmpâ âÂÂimage/x-bmpâ Windows Metafile WMF , EMF âÂÂimage/x-win-metafileâ âÂÂimage/x-wmfâ WordP erfect WPD â application/wordperfect5â 4/5/6/7/8 â application/wordperfect5.1â â application/x-wordperfect6â Table 1 Supported e-mail attachments The Nokia 9290 Communicator supports the following e-mail attachment types:
8. NOKIA 9290 COMMUNICA T OR AND W AP SERVICE Contents: 8.1 Introduction 8.2 Defining WAP access points manually 8.3 Setting home page 8.4 Supported images, their suffixes, and MIME-types
8.1 Introduction Before you can use the WAP services, you need to configure your W AP settings. Y our WAP service provider will provide you with the exact values for the W AP settings. Follow the instructions carefully . Y ou can use this information to define and edit the settings manually . Also, your service provider may be able to send some, or all, of the required settings to you via a special short message called an Over the Air (OT A) message. After you have received the settings, you can start using the WAP applica- tion or edit the settings as described below . Note: The necessary settings for WAP configuration are provided by your W AP service pro vider . Depending on your service pro vider , you may not need to fill in all of the settings. 8.2 Defining WAP access points manually To set up a new W AP access point, open Internet startup under the Extras application, and select WAP access (a shortcut to Internet startup can also be found in the Desk application). 1. Open Internet startup from Desk or from under Extras. 2. Select WAP access and press Open. 3. Fill in the following settings. Contact your WAP service provider for the correct settings. ⢠Name â Create a name for the access point that you can recognize easily . ⢠Secure connection â Choose whether to Use secure connection, according to your service providerâÂÂs instructions. ⢠Internet access â From a selection list, choose the Internet Access Point (IAP) you want to use for this connection. If you have no configured IAPs, you can create a new one by pressing New Internet access. ⢠Gateway IP address â T ype in the IP address that the WAP gateway uses. 4. Press Close to exit the WAP access point settings. 8.3 Setting home page 1. Press the Internet button and open the W AP application. 2. Press the Menu key , and open the Settings dialog under the T ools menu. 3. T o activate the Home page tab, press the Menu button. 4. T ype in the WAP home page URL. 5. Choose the WAP access point you want to use. 6. Press Done to exit the WAP settings. 8.4 Supported images, their suffixes , and MIME-types In addition to WBMP image format, the Nokia 9290 Communicator supports all the most commonly known image formats. Note: Some WAP gateways may not support all of these content types. Nokia W AP gateway products support all the content types listed here: ⢠a WBMP (Wireless Bitmap), âÂÂimage/vnd.wap.wbmpâ â¢ a JPEG file (incl. Progressive), â .JPGâÂÂ, âÂÂimage/jpegâ â¢ a GIF file (incl. anim-gif), â .GIFâÂÂ, âÂÂimage/gifâ â¢ a PNG file, â .PNGâÂÂ, âÂÂimage/pngâ The WAP Service Developerâ s Guide for the Nokia 9290 Com- municator , which is available at www .forum.nokia.com , contains more detailed information about WAP and the Nokia 9290 Communicator . 30
9. NOKIA 9290 COMMUNICA T OR AND REMO TE / OVER THE AIR (O TA) CONFIGURING Contents: 9.1 General 9.2 Further information and support 9.3 Creating configuration messages 9.3.1 Configuration over SMS only 9.3.2 Non-supported feature sets 9.3.3 Further deviations
9.1 General This chapter shows how the Nokia 9290 Communicator can be configured remotely using SymbianâÂÂs Bearer Indepen- dent Object (BIO) messaging. Remote configuration helps the end user to get the most out of the device as quickly as possible. Complex settings, such as Internet settings, can be âÂÂpushedâ to the device by the carrier or the help desk of an Internet service provider or a corporate IT department. The configuration messages are sent to the Nokia 9290 Communicator using the GSM Short Message Service (SMS). For maximizing the compatibility and minimizing the transition period for help desks, the BIO messaging support for the Nokia 9290 Communicator is similar to Nokia Smart Messaging, which is supported by earlier Nokia 9290 Communicators. The development of the Symbian platform may introduce new BIO message types in the future that leverage the new features of the Nokia 9290 Communicator and the Symbian operating system. WAP settings can be configured using OT A (Over the Air) configuration syntax. 9.2 Further information and support The supported message syntax is based on Smart Messaging Specification 3.0.0, Nokia Mobile Phones, 2000. The document is available from the Forum Nokia W eb site at www .forum.nokia.com/, Smart Messaging section. The syntax for W AP settings is based on WAP Over the Air settings specifications, available from the Forum Nokia Web site at www .forum.nokia.com/, Smart Messaging section. For details on what the Internet settings mean, please refer to chapters 5 and 6 in this document. 9.3 Creating configuration messages The creation and syntax of Smart Messaging-type config- uration messages is specified in the Smart Messaging specification mentioned in section 9.2. That specification contains the details on how the messages should be created and sent. The following sections list the deviations from that specification. 9.3.1 Configuration over SMS only At the moment, the only way to transfer a configuration message to the Nokia 9290 Communicator is over the GSM Short Message Service. T ransferring the configuration messages over HTTP (in Web) or as e-mail attachments is not supported yet. The Nokia 9290 Communicator is a WAP device and as such all Smart Messages should be sent to WDP ports, as specified in the Smart Messaging specification. If this is not possible, keyword headers (also known as compatibility headers) can also be used. NBS port numbers, on the other hand, should not be used. 9.3.2 Non-supported feature sets Some of the following feature sets were specified in older versions of the Smart Messaging document. They are listed for the sake of completeness. ⢠TTML (T agged Text Markup Language) is considered as âÂÂdeprecated.â WAP and WML have replaced TTML. The Nokia 9290 Communicator does not support TTML. ⢠DMCP (Dynamic Menu Control Protocol) is not sup- ported by the Nokia 9290 Communicator . The majority of features are activated from the PDA side of the Nokia 9290 Communicator; therefore, dynamic menus on the phone side are not supported. ⢠Service Cards are not supported. Service Card func- tionality can be used with normal business cards that have a phone number field for each service. T o converge with the de facto standards, the Nokia 9290 Communicator supports the vCard business card format, which can be used for this purpose. ⢠Extended Configuration Syntax is not supported at the moment, except for the Short Message Center number setting. 9.3.3 Further deviations ⢠The Notify text field in the basic Internet configuration message is now optional, rather than mandatory . Hence, the first line of the definition now reads: <iap-message> ::= [<iap-compatibility-header>] [<notify-text>] <info-body> ⢠Script version and script data fields in Internet configuration settings are not used in the Nokia 9290 Communicator . 32
1 0. NOKIA 9290 COMMUNICA TOR AND SECURITY Contents: 1 0.1 Hardware and SIM card security 1 0.2 Radio interface security 1 0.3 Software security 1 0.4 Internet and intranet 1 0.4.1 Incoming data calls 1 0.4.2 Attacks from the Internet 1 0.4.3 Dial-up security 1 0.5 SSL and TLS 1 0.5.1 Web browser 1 0.5.2 Reading and sending mail 1 0.5.3 Supported encryption algorithms 1 0.6 WAP security
1 0.1 Hardware and SIM card security The following security methods can be used to ensure Nokia 9290 Communicator hardware and SIM card security (for details and activation/deactivation, please refer to the Nokia 9290 Communicator User Guide): ⢠PIN code & PUK code ⢠Security code for SIM change security ⢠Device lock â to lock the whole device ⢠Call restriction â to restrict incoming or outgoing calls 1 0.2 Radio interface security The security of the radio connection between a GSM phone and the GSM network is specified in the GSM standards. The GSM network specifies the radio interface security level, and the encryption applies to voice, data, and fax calls. Note that encryption is only used between the GSM phone and the base station. The level of security in the radio transmissions depends on the network and the local laws. GSM short messages (SMS) are transported using the GSM signaling channels, but these signaling channels are not encrypted. Therefore, short messages are not a secure way to transport data. 1 0.3 Software security As the Nokia 9290 Communicator is a versatile and open programming environment, anyone can create new software for it. The Nokia 9290 Communicator has a secure software installation system that can be used to minimize the risks posed by the possible malicious software. Software is distributed in software packages called SIS files. These packages can be digitally signed. By signing a soft- ware package, the originator of the package makes sure that the package cannot be modified while it is being stored, or while it is en route to the Nokia 9290 Communicator . When installing software, the user will see the alleged originator of the package and the party that authenticates the originatorâ s identity . T o view the currently trusted certification authorities, the user can go to the Certificate management tool. The user can edit trust settings for each listed certificate. By giving a certificate a âÂÂtrustedâ status, the user vouches that he/she knows that a given certificate really belongs to the given entity . In order to maximize software security in your Nokia 9290 Communicator: ⢠When editing trust parameters in the Certificate management tool in Control panel, only trust those certificates whose origin you can be sure of, and you know that the certificate really belongs to the entity whose name is on the certificate. If you are in doubt, contact the certification authorities help desk and ask them for their certificate âÂÂMD5 fingerprint.â Compare the âÂÂfingerprintâ with the one that is displayed in the Certificate management tool. ⢠Make sure that the software is intended for the Nokia 9290 Communicator . ⢠Only install software that comes in SIS files. Never install raw DLLs or EXEs. ⢠Only install software that has been signed and only if you trust both the author and the certification authority . ⢠During the installation, be sure to read the dialogs that are presented to you. They may contain further security information. ⢠Nokia runs a Nokia OK logo program for third-party software developers. Using software that has the Nokia OK logo offers further assurances on the quality of the software. 1 0.4 Internet and intranet Data communications over the Internet or other IP networks is not secure by default. To enable secure connections, the Nokia 9290 Communicator supports various security protocols. 1 0.4.1 Incoming data calls By relying only on the factory configuration, it is not possible to access the Nokia 9290 CommunicatorâÂÂs files from an incoming data call. However , as with any normal computer , malicious third-party software can potentially degrade the security of the device. Therefore, only install and use soft- ware that comes from a trusted source and is digitally signed by a trusted party . 1 0.4.2 Attacks from the Internet When the Internet connection is up, it is possible to send data packets from the Internet to the Nokia 9290 Commu- nicator . As the wireless link is low-bandwidth, it is potentially possible to cause congestion by sending large amounts of bogus packets to the device. Therefore, it is recommended that the dial-up link uses a firewall to filter suspicious packets. Many Internet service providers offer this service. The use of dynamic IP addresses is another recommended safety measure. Most, if not all, Internet service providers supply dial-in clients with dynamic IP addresses by default. Also, installing defective or malicious third-party software (especially from Internet servers) in Nokia 9290 Communica- tors may degrade the security . Only install and use software that comes from a trusted source and is digitally signed by a trusted party . 1 0.4.3 Dial-up security The Nokia 9290 Communicator requires a PPP (P oint to P oint Protocol) connection to allow connection to the Internet/intranet. The supported authentication protocols are P AP (P assword Authentication Protocol) [RFC 1334], CHAP (Challenge Handshake Authentication Protocol) [RFC 1994], and MS-CHAP (Microsoft variant of CHAP). 34
To enhance the security of P AP , CHAP , and MS-CHAP , some other authentication methods can be used when creating a network connection. If the method works with normal PAP or CHAP , it can be used with the Nokia 9290 Communicator . Other login schemes can be supported using a login script. Some of the alternatives are: ⢠Callback system (supported PPP callback protocols: IETF type 0 [RFC 1570] and the Microsoft callback protocol) ⢠Centralized security (authentication server configured based on RADIUS [RFC 2 138] and TACACS [RFC 1492]) ⢠Multiple P asswords and one-time password schemes ⢠Token-based security 1 0.5 SSL and TLS The Nokia 9290 Communicator supports the SSLv3 (Secure Socket Layer) and TLSv1 (Transport Layer Security) protocols. These protocols are integrated in the socket interface, so third-party programs can easily use these protocols to offer secure Internet connections. 1 0.5.1 Web browser Web URLs (addresses) that start with âÂÂhttpsâ are SSL-secured connections. The SSL connection is negotiated with t he server and then the data is transferred over the encrypted connection. A small lock symbol is displayed as an indication that the connection is encrypted. The encryption strength depends on the SSL server . The Nokia 9290 Communicator supports strong 128 bit encryption in SSL and TLS, but can downgrade its security to a lower level if the server is not capable of handling such strong encryption. The authenticity of the Web server is determined by the help of certificates in the Certificate management tool. As discussed above in the software security chapter , the user can select which certificates are trusted and which are not. When connecting to a server , whose identity is certified by a trusted party , there will be no warning note. Other- wise, the user will be able to review the identification offered by the remote server . Some certification authority root certificates are factory-installed on the device; Nokia does not endorse any specific certification authority . The HTTP (Hypertext T ransfer Protocol) also provides a simple authentication protocol, which uses a username/ password pair . It can be used to authenticate the user to a remote server . This method can be used over the SSL for additional security . 1 0.5.2 Reading and sending mail Access to remote mailboxes (IMAP and POP) and sending mail (SMTP) can also be secured using the SSL/TLS. Y ou can request a secure connection by ticking the appropriate box in the settings. In order to use secure connections with electronic mail, the mail server has to support the âÂÂstarttlsâ command (IMAP , SMTP) or the âÂÂstlsâ command (POP). Note: Sending electronic mail o ver a secure connection does not encrypt the mail itself, only the connection to the mail server . After the mail continues to its destination from the first mail server , it is not encrypted. This feature is most useful when accessing mail servers in a secure intranet through a public Internet service provider . 1 0.5.3 Supported encryption algorithms The selection of algorithms depends on the protocol being used. It is advisable to avoid the use of â export-gradeâ algorithms (RC4 with 40 secret bits and DES) for security reasons. The Nokia 9290 Communicator supports the following cryptographic algorithms in SSL/TLS: ⢠For server authentication and/or key exchange: RSA, DSA, and Diffie-Hellman ⢠For data encryption: RC4⢠(plus the âÂÂexportâ version with 40 secret bits), DES, and Triple-DES 1 0.6 WAP security When using WAP for a data call, the dial-up security is the same as with Internet services. Please refer to the chapter above. WAP uses an optional security layer called WTLS. This can be turned on in the settings, or the server can mandate it. WTLS security ends at the WAP gateway . Connections to the target server from the WAP gateway might not be encrypted. WAP Forum specifies WTLS. The Nokia 9290 Communicator supports strong 128 bit encryption in WTLS, but is able to lower the security level if required by the server . The Nokia 9290 Communicator supports server authentication and key exchange using the RSA algorithm and data encryption using the RC5⢠algorithm. The gateway is authenticated using certificates. Some certification authority root certifi- cates are factory-installed on the device; Nokia does not endorse any specific certification authority . 35
1 1. FORUM NOKIA - COMMUNITY FOR DEVELOPERS Contents: 1 1.1 Introduction 1 1.2 Information for Symbian application developers 1 1.3 Developing optimized WAP services 1 1.4 Nokia Developer ProPoint 1 1.5 Third-party connectivity solutions
1 1.1 Introduction Forum Nokia is an online community for third parties developing applications and services for Nokia platforms. The Forum Nokia Web site provides information for different technologies and platforms for developers, system integrators, content providers, and for others who are interested in the mobile application development. Marketing support as well as possibility for application certification is provided via the developer alliances, Nokia Developer ProP oint, and Nokia Developer NetP oint. After free registration to Forum Nokia, the registered members can find supporting documents, toolkits, and software development kits (SDKs) and share development tips and find solutions to problems in the Online Discus- sion areas. Y ou can find the Forum Nokia Web site at www .forum.nokia.com . 1 1.2 Information for Symbian application developers As the Symbian operating system of the Nokia 9290 Communicator is an open platform by Symbian, third-party developers can create additional software applications for the Nokia 9290 Communicator . The Symbian application developers can register to the Symbian Platform section in Forum Nokia. Besides downloading supporting documents, the Software Development Kit (SDK) for Symbian operating system application development can be ordered here. The SDK CD-ROM includes both the C SDK and Java⢠SDK, and both programming languages can be used in the application development. 1 1.3 Developing optimized WAP services Forum Nokia also offers guidance in developing optimized WAP services for the Nokia 9290 Communicator , as well as for other Nokia WAP phones. The Nokia W AP Toolkits can be downloaded for free, and several WAP service development related discussion areas are on hand. 1 1.4 Nokia Developer ProPoint Companies that want to develop applications and services in closer relationship with Nokia can apply for the Nokia Developer ProP oint. Members of Nokia Developer ProPoint can get technical assistance, marketing support, and other membership benefits during their membership period. See the Forum Nokia Web site at www .forum.nokia.com for further information on services, price, and availability . 1 1.5 Third-party connectivity solutions Since the Nokia 9290 Communicator has both an infrared and a serial port, it is possible to connect different kinds of external devices to it. Third-party connectivity solutions include, for example, bar code readers, GPS receivers, digital still cameras, and portable scanner applications. 37
12. ABBREVIA TION
39 Abbreviation: bps bits per second CHAP Challenge Handshake Authentication Protocol CMT Cellular Mobile Telephone DNS Domain Name Server DTMF Dual Tone Multi Frequency GSM Global Digital System for Mobile Communications HSCSD High Speed Circuit Switched Data HTML HyperText Markup Language IAP Internet Access Point IMAP Internet Mail Access Protocol IP Internet Protocol IrDA Infrared Data Association ISP Internet Service Provider IT Information T echnology MIME Multi-purpose Internet Mail Extensions MMC MultimediaCard NIM Nokia Interleaved Multimedia PAP P assword Authentication Protocol PDA P ersonal Digital Assistant POP P ost Office Protocol PPP P oint to Point Protocol SIM Subscription Identification Module SMSC Short Message Service Center SMTP Simple Mail Transfer Protocol SSL Secure Socket Layer TCP Transport Control Protocol TLS Transport Layer Security URL Uniform Resource Locator USSD Unstructured Supplementary Service Data WAP Wireless Application Protocol WML Wireless Markup Language WWW World Wide Web
13. SHORT CUTS FOR THE NOKIA 9290 COMMUNICA T OR
41 The Nokia 9290 Communicator supports Windows TM -like shortcuts. The table below lists some of the available shortcuts: Shortcuts for the Nokia 9290 Communicator: Tip: Y ou can find more shortcuts in the menus on the display of the Nokia 9290 Communicator interface. Shortcut Function Ctrl a Selects all Ctrl c Copies selected text Ctrl x Cuts selected text Ctrl v P astes selected text Ctrl z Undoes (the last action) Ctrl b Applies bold Ctrl i Applies italics Ctrl u Applies underlining Ctrl t Full screen mode (if available) Ctrl d Delete files, messages, shortcuts, and other items Ctrl p Print or Properties Ctrl n Creates a new file Ctrl o Open Ctrl e Close Ctrl s Save Ctrl Shift s Save As Chr left/right arrow (on Arrows key) Moves the cursor to the beginning or end of the line Chr up/down arrow (on Arrows key) Moves up or down a page Chr Ctrl up/down arrow (on Arrows key) Moves to start or end of document Shift Ctrl left/right arrow (on Arrows key) Selects the previous or next word Shift right/left/up/down arrow (on Arrows key) Selects one text character or line Shift Chr up/down arrow (on Arrows key) Selects text, page by page, inside a document
14. SETUP CHECKLIST
43 For online Help at any time, press the key on the Nokia 9290 Communicator keyboard. Y ou are shown a page of information relevant to the task you are doing. Y ou can also search the Help topics for specific subjects and keywords. Setup checklist MAIL SMS INTERNET WA P Information you need Where to obtain it Where to insert it Write it here Mail address of your remote If you have an existing mail See âÂÂMailâ in the User Guide. mailbox account, this address is your The General page of Mail mail address settings dialog: Your mail address Username and password of Y our mailbox service Username and Password your mailbox provider IAP to connect to your mailbox Y our mailbox service Use Internet access point provider The protocol of your remote Y our mailbox service The Servers page: POP3 or IMAP4 mailbox provider Mailbox type IP (Internet Protocol) address Y our mailbox service Outgoing mail server or host name of the server that provider sends your mail IP address or host name of the Y our mailbox service Incoming mail server server that receives your mail provider Service center number Home network carrier See âÂÂSMSâ in the User Guide. The Settings page of the SMS settings dialog: Service center in use WWW Internet access point: Y our Internet service See âÂÂInternet connectionsâ name, modem phone number , provider in the User Guide. Internet username, and password access, connections details dialog Data call type information: Y our GSM network carrier Internet access, connection whether high-speed call details dialog, Advanced settings, Data Call page Data call type information: Y our Internet service As above remote modem type provider WAP Internet access point: Y our WAP service provider See âÂÂW APâ in the User Guide. name, modem phone number , Internet access, connection username, and password settings dialog Data call type information: Your GSM network carrier Internet access, connection whether high-speed call details dialog, Advanced settings, Data Call page Data call type information: Your WAP service provider As above remote modem type WAP Internet access point: Y our WAP service provider WAP access point settings gateway IP address dialog
Legal Notices Reproduction, transfer , distribution, or storage of part or all of the contents in this document in any form without prior written permission of Nokia is prohibited. Copyright é 2002 Nokia. All rights reserved. Nokia, Nokia Connecting P eople, Nokia 9290 and Nokia original accessories logo are trademarks or registered trademarks of Nokia Corporation. Java is a trademark of Sun Microsystems, Inc. Other company and product names mentioned herein may be trademarks or trade names of their respective owners. Nokia operates a policy of ongoing development. Nokia reserves the right to make changes and improvements to any of the product s described in this document without prior written notice. UNDER NO CIRCUMSTANCES SHALL NOKIA BE RESPONSIBLE FOR ANY LOSS OF PROFITS, INCOME, DAT A, REVENUE OR TIME OR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL INDIRECT OR PUNITIVE DAMAGES HOWSOEVER CAUSED. THE CONTENTS OF THIS DOCUMENT ARE PROVIDED âÂÂAS IS.â EXCEPT AS REQUIRED BY APPLICABLE LA W, NO WARRANTIES OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO , THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE MADE IN RELA TION TO THE ACCURACY, RELIABILITY OR CONTENTS OF THIS DOCUMENT . NOKIA RESERVES THE RIGHT TO REVISE THIS DOCUMENT OR WITHDRAW IT AT ANYTIME WITHOUT PRIOR NOTICE. Important Safety Notes All the safety instructions in your phoneâÂÂs user guide and computer also apply when this product is used with the phone. Remember to make backup copies of all important data to protect against possible loss or alteration. Do not point the infrared beam into anyoneâÂÂs eyes or allow it to interfere with other infrared devices. To disconnect the cable from the Nokia Communicator , hold the connector and remove the cable. Export Controls This product contains commodities, technology , or software exported from the United States in accordance with the Export Administration regulations. Diversion Contrary to U.S. law is prohibited. FCC/Industry Canada Notice Your phone may cause TV or radio interference (for example, when using a telephone in close proximity to receiving equipment). The FCC or Industry Canada can require you to stop using your telephone if such interference cannot be eliminated. If you require assistance, contact your local service f acility . This device complies with part 15 of the FCC rules. Operation is subject to condition that this device does not cause harmful interference. Please refer to the Nokia 9290 Communicator user guide (also available at www .Communicatorworld.net or www .nokia.com ) to learn more about this productâÂÂs features. Learn about Nokia products and Nokia at www .nokia.com . Nokia is a broadly held company with listings on six major exchanges, including the New York Stock Exchange (NYSE symbol: NOK).
Nokia Inc. 7725 Woodland Center Boulevard, Suite 150, T ampa, Florida 33614 www .nokia.com www .Communicatorworld.net 1-800- 4MY -9290 Copyright é 2002 Nokia. All rights reserved. Nokia, Nokia Connecting P eople, Nokia 9290 and Nokia original accessories logo are trademarks or registered trademarks of Nokia Corporation. N4125 5/0 2