Nokia Mediamaster 230 T User Manual

Bedienungsanleitung User Guide Instruc ciones de uso Käytt öohje Bruksanvisning
EN Nokia hereby declares that this digital receiver , Mediamaster 230 T , is in con- formity with essential requirements and other relevant provisions of Directive 1999/5/EC. This T erminal Equipment is intended for connection to the analogue Public Switched T elephone Networks (PSTNs), in which network addressing, if provided, is by means of Dual T one Multiple Frequency (DTMF) signalling.
GB 3 Quick Guide Connecting a TV and a video recorder Preparing the Remote Control Language • Select the desired menu language with cursor up/ down. (Cursor = see page 9.) This will also become the main lan- guage for audio and subtitling. •W hen you now press select again to confirm your choice of language, you simultaneously start the searching for TV/ radio channels. Channel search in progress This menu will be shown as long as the Mediamaster is searching for TV and radio channels. All channels found will be listed on the screen. Please note that the search procedure may take a few min- utes. Y ou may cancel the search at any time by pressing select . When the search procedure has ended, a message will tell how many TV and radio channels have been found. •P ress select to continue. 1 2 3 SCART RF video Switching on for the first time •P lug in your Mediamaster . • The “First time installation” menu is shown • Press the select button on the remote control to start the installation procedure.
GB 4 Ti me adjustment The time is adjusted ± 1/2 hour at a time by using cursor up/ down . Y ou can also adjust the minutes by using cursor left/right . • Press select to finish the First time installation and watch TV channels. Quick Guide
GB 5 Nokia, Nokia Connecting People and Navi Bars are registered trademarks of Nokia Corporation. Other product and company names mentioned herein may be trademarks or trade names of their owners. Nokia operates a policy of continuous development. Therefore we reserve the right to make changes and improvements to any of the products described in this manual without any prior notice. Copyright © 2003 Nokia. All rights reserved. Contents Contents Quick Guide 3-4 Contents 5 Nokia Mediamaster software end- user license 6-7 General information about the Mediamaster 8 Remote control 9 Front and rear panel 10 About the smart card and CA module 11 Connecting the Mediamaster 12 About the SCAR T sockets 12 Preparing the remote control 12 About the digital transmission 13 Connecting to the TV aerial 13 Connecting the Mediamaster to the TV 14 Connection of a video recorder 14 General 15 Connecting a HiFi system 15 Procedure when RF connections are used 15 First time installation 16 General information 16 Switching on for the first time and start the First time installation 16 Language 16 Ti me adjustment 17 Channel search in progress 17 Vi ewing mode 18 General Information 18 Programme information 18 Extended programme information 19 T emporary settings 19 External equipment 20 T eletext 20 Navi Bars 21 General information 21 The “Control” and “Settings” folders 22 Control folder ☛ User 22 Control folder ☛ Edit channels 22 Vi ewing images received from an external device. (Bluetooth connection) 26 Control folder ☛ Connections 26 Control folder ☛ T i mer 28 Control folder ☛ System info 28 Settings folder ☛ Channel 29 Settings folder ☛ T V 3 0 Settings folder ☛ Access 31 Settings folder ☛ T i m e 31 Settings folder ☛ SW update 32 Settings folder ☛ Reinstall 32 Games folder 32 Glossary 33 Tr oubleshooting 34 T echnical specifications 35
GB 6 Nokia Mediamaster software end-user license IMPORT ANT : READ CAREFULL Y BEFORE OR USING THE SOFTW ARE NOKIA CORPORA TION, NOKIA HOME COMMUNICA TIONS END-USER SOFTW ARE AGREEMENT This Software Agreement (“Agreement”) is between Y ou (either an individual or an entity), the End User , and Nokia Corporation, Nokia Home Communications (“Nokia”). The Agreement authorizes Y ou to use the Software specified in Clause 1 below and which is included in this Nokia digital TV receiver . This is an agreement on end-user rights and not an agreement concerning sale. Read this Agreement carefully before using the Software. By using this Nokia digital TV receiver , Y ou agree to the terms and conditions of this Agreement. If Y ou do not agree to all of the terms and condi- tions of this Agreement, return this Nokia digital TV receiver and accompanying documentation to the place of purchase. YOU AGREE THA T YOUR USE OF THE SOFTW ARE ACKNOWLEDGES THA T YOU HA VE READ THIS AGREEMENT , UNDERST AND IT , AND AGREE TO BE BOUND BY ITS TERMS AND CONDITIONS. 1. SOFTW ARE. As used in this Agreement, the term “Software” means, collectively: (i) the soft- ware product identified above (ii) digital images, stock photographs, clip art, or other artistic works (“Stock Files”) (iii) related explanatory written ma- terials and any other possible documentation re- lated thereto (“Documentation”); (iv) fonts, and (v) upgrades, modified versions, updates, additions, and copies of the Software, if any , licensed to Y ou by Nokia under this Agreement. 2. END-USER RIGHTS AND USE. Nokia grants to Y ou non-exclusive, non-transferable end-user rights to use the Software on this Nokia digital TV receiver only . 3. LIMIT A TIONS ON END-USER RIGHTS. Y ou may not copy , distribute, or make derivative works of the Software except as follows: (a) Y ou may transfer all your rights to the Software at the same time as Y ou transfer this Nokia digital TV receiver on a permanent basis, provided that Y ou transfer this Nokia digital TV r eceiver and all copies of the related Documentation, do not retain any copies by yourself, and the recipient agrees to the terms and conditions of this Agreement. (b) Y ou may not use, modify , translate, reproduce, or transfer the right to use the Software or copy the Software except as expressly provided in this Agreement. (c) Y ou may not resell, except as set forth in clause 3 (a), sublicense, rent, lease, or lend the Software. (d) Y ou may not reverse engineer , decompile, dis- assemble, or otherwise attempt to discover the source code of the Software (except to the extent that this restriction is expressly prohibited by law) or create derivative works based on the Software. (e) Unless stated otherwise in the Documentation, Y ou shall not display , modify , reproduce, or distrib- ute any of possible the Stock Files included with the Software. In the event that the Documentation allows Y ou to display the Stock Files, Y ou shall not distribute the Stock Files on a stand-alone basis, i.e., in circumstances in which the Stock Files con- stitute the primary value of the product being dis- tributed. Y ou should review the “Readme” files (if any) associated with such Stock Files that Y ou use to ascertain what rights Y ou have with respect to such materials. Stock Files may not be used in the production of libelous, defamatory , fraudulent, in- fringing, lewd, obscene, or pornographic material or in any otherwise illegal manner . Y ou may not register or claim any rights in the Stock Files or derivative works thereof. (f) Y ou agree that Y ou shall only use the Software in a manner that complies with all applicable laws in the jurisdiction in which Y ou use the Software, including, but not limited to, applicable restrictions concerning copyright and other intellectual property rights. 4. COPYRIGHT . The Software and all rights, with- out limitation including proprietary rights therein, are owned by Nokia and/or its licensors and affili- ates and are protected by international treaty pro- visions and all other applicable national laws of the country in which it is being used. The structure, organization, and code of the Software are the valu- able trade secrets and confidential information of Nokia and/or its licensors and affiliates. Y ou must not copy the Software 5. COMMENCEMENT & TERMINA TION. This Agreement is effective from the first date Y ou use this Nokia digital TV receiver . Y ou may terminate this Agreement at any time by returning, at Y our own costs, this Nokia digital TV receiver , and all related materials provided by Nokia. Y our end-user rights automatically and immediately terminate
GB 7 Nokia Mediamaster software end-user license without notice from Nokia if Y ou fail to comply with any provision of this Agreement. In such an event, Y ou must immediately return at Y our own cost, this Nokia digital TV receiver , and all related material to the place of purchase. 6. NO OTHER OBLIGA TIONS. This Agreement creates no obligations on the part of Nokia other than as specifically set forth herein. 7. LIMIT A TION OF LIABILITY . TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LA W , IN NO EVENT SHALL NOKIA, ITS EMPLOYEES OR LICENSORS OR AFFILIA TES BE LIABLE FOR ANY LOST PROFITS, REVENUE, SALES, DA T A, OR COSTS OF PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES, PROPER TY DAMAGE, PERSONAL INJURY , INTERRUPTION OF BUSI- NESS, LOSS OF BUSINESS INFORMA TION, OR FOR ANY SPECIAL, DIRECT , INDIRECT , INCIDEN- T AL, ECONOMIC, COVER, PUNITIVE, SPECIAL, OR CONSEQUENTIAL DAMAGES, HOWEVER CAUSED AND WHETHER ARISING UNDER CON- TRACT , TORT , NEGLIGENCE, OR OTHER THEOR Y OF LIABILITY ARISING OUT OF THE USE OF OR INABILITY TO USE THE SOFTW ARE, EVEN IF NOKIA OR ITS LICENSORS OR AFFILIA TES ARE ADVISED OF THE POSSIBILITY OF SUCH DAM- AGES. BECAUSE SOME COUNTRIES/ST A TES/ JURISDICTIONS DO NOT ALLOW THE EXCLU- SION OF LIABILITY , BUT MA Y ALLOW LIABILITY TO BE LIMITED, IN SUCH CASES, NOKIA, ITS EMPLOYEES OR LICENSORS OR AFFILIA TES’ LIABILITY SHALL BE LIMITED TO U.S. $50. Nothing contained in this Agreement shall preju- dice the statutory rights of any party dealing as a consumer . Nokia is acting on behalf of its employ- ees and licensors or affiliates for the purpose of disclaiming, excluding, and/or restricting obliga- tions, and liability as provided in this clause 7, but in no other respects and for no other purpose. 8. EXPORT CONTROL. The Softwar e, including technical data, includes cryptographic software subject to export controls under the U.S. Export Administration Regulations (“EAR”) and may be subject to import or export controls in other coun- tries. The EAR prohibits the use of the Software and technical data by a Government End User , as defined hereafter , without a license from the U.S. government. A Government End User is defined in Part 772 of the EAR as “any foreign central, re- gional, or local government department, agency , or other entity performing governmental functions; including governmental research institutions, gov- ernmental corporations, or their separate business units (as defined in part 772 of the EAR) which are engaged in the manufacture or distribution of items or services controlled on the Wassenaar Munitions List, and international governmental organizations. This term does not include: utilities (telecommuni- cations companies and Internet service providers; banks and financial institutions; transportation; broadcast or entertainment; educational organiza- tions; civil health and medical organizations; retail or wholesale firms; and manufacturing or industrial entities not engaged in the manufacture or distri- bution of items or services controlled on the W assenaar Munitions List.)” Y ou agree to strictly comply with all applicable import and export regu- lations and acknowledge that Y ou have the respon- sibility to obtain licenses to export, re-export, trans- fer , or import the Software. Y ou further represent that Y ou are not a Government End User as defined above, and Y ou will not transfer the Software to any Government End User without a license. 9. CONT ACT DET AILS. If Y ou want to contact Nokia in respect of this Agreement, contact Nokia at the following address: Nokia Home Communications Itämerenkatu 11 - 13, 00180 HELSINKI FINLAND 10. APPLICABLE LA W & GENERAL PROVISIONS. This Agreement is governed by the laws of Finland. All disputes arising from or relating to this Agree- ment shall be settled by a single arbitrator ap- pointed by the Central Chamber of Commerce of Finland. The arbitration procedure shall take place in Helsinki, Finland in the English language. If any part of this Agreement is found void and unenforce- able, it will not affect the validity of the balance of the Agreement, which shall remain valid and en- forceable according to its terms. This Agreement may only be modified in writing by an authorized officer of Nokia. This is the entire agreement between Nokia and Y ou relating to the Software, and it supersedes any prior representations, discussions, undertakings, end-user agreements, communications, or adver - tising relating to the Software.
GB 8 General information about the Mediamaster Throughout this manual you will notice that the everyday operation of your Mediamaster is based on a series of user friendly on-screen displays and menus. These menus will help you get the most from your Mediamaster , guiding you through installation, channel selec- tion, viewing and many other functions. All functions can be performed by using the buttons on the remote control, and some of the functions can also be performed by using the buttons on the front panel. Please be aware that new software may change the functionality of the Mediamaster . Should you experience any difficulties with the operation of your Mediamaster , please consult the relevant section of this manual, in- cluding the T roubleshooting, or alternatively call your dealer or a cus- tomer service adviser . •A llow 10 cm space around the Mediamaster for sufficient ventilation. •D o not cover the Mediamaster’ s ventilation openings with items such as newspapers, tablecloths, curtains etc. • Do not place the Mediamaster on top of a unit that emits heat. • Do not place naked flame sources, such as lighted candles, on the Media- master . • Use a soft cloth and a mild solution of washing-up liquid to clean the cas- ing. • Do not expose the Mediamaster to dripping or splashing liquids. •D o not place any objects filled with liquids, such as vases, on the Media- master . •T o give your Mediamaster an extra protection, e.g. at a thunderstorm, we recommend that you connect it via an external surge protection device. • Do not connect or modify cables when the Mediamaster is plugged in. • Do not remove the cover . • Do not allow the unit to be exposed to hot, cold or humid conditions. • Service should be carried out only at a Nokia Authorised Service Centre. •P lease note that the only way to isolate the Mediamaster completely from the mains supply is to unplug the mains cable! IMPORT ANT! Read this before using the Mediamaster!
GB 9 Press once to turn the sound off/on (mute). Press and hold for a few seconds to switch the Mediamaster in and out of standby mode. 0 - 9 Change channel and to select individual menu options. Note: If 0 is entered as the first digit, the TV Release func- tionality is activated (see below). 0 To toggle between the 230 T and any equipment connected to the AUX Scart; e. g. a V ideo recorder or a satellite receiver . info In viewing mode: T o display short and extended information (if transmitted) about current and next programmes. In Navi Bars with a bookmark in focus: Will show informa- tion about the bookmark. back Go back one level at a time within menus without storing any settings. To toggle between present and previous TV/Radio channel in viewing mode. Close the Navi Bars. select Confirm the selection of a highlighted item. Open the Navi Bars. opt Select options in viewing mode. txt Press to enter teletext (if available). This section describes how to operate the Mediamaster using the buttons on the remote control. Some of the functions can also be performed by using the buttons on the front panel. Remote control Cursor up Move up in the menus and change to the next channel in viewing mode. Cursor down Move down in the menus and change to the previous channel in viewing mode. Cursor left Move left/change set- tings in menus. Decrease the volume level in viewing mode. Cursor right Move right/change settings in menus. Increase the volume level in viewing mode. The cursor button
GB 10 Front panel Front and rear panel AUDIO L R RCA connectors stereo outputs for con- nection to an analogue HiFi system TV SCART for connection to the TV AUX SCAR T for connection to a VCR or a satellite receiver DIGIT AL AUDIO RCA connector S/PDIF digital out- put for connection to a HiFi system Mains cable 110-240 V AC 50-60 Hz TV aerial for an external or an indoor TV aerial Rear panel SERIAL PORT for connection to a PC Power supply only for connection of a NOKIA indoor TV aerial with signal amplifier . 5V 30 mA. Aerials from other manufacturers may NOT be powered from this connection. Function ON Standby Locked to channel Remote control feedback SW download Error Indicator 1 Green Red Green Green Continuous green flashing Continuous red flashing Indicator 2 Green - Red if not locked. Single flash Continuous green flashing Continuous red flashing to put the Mediamaster in and out of standby mode to change channels Indica- tor 1 Indica- tor 2 Slot Not in use Lid TV/VCR for an RF-cable to the aerial input of the TV or VCR Slot for a CA module with a smart card Button push the button to release a CA mod- ule that has been inserted.
GB 11 General To be able to receive terrestrial scrambled digital channels you will need a CA module and a smart card from a Service Provider . There are a few different CA modules on the European market. Each one of the CA modules support a certain kind of encryption system. The Mediamaster supports CA modules which are made to work according to the DVB standard. Depending on which country you use the Mediamaster in, your local dealer will pro- vide you with the right type of CA module. Please note that a smart card may only be valid for a single Serv- ice Provider and due to this, a specific range of channels. The smart card and the CA module may cause special menus, not described in this manual, to appear . Follow the instructions from the Service Provider . Note: CA modules and smart cards are only distributed by Serv- ice Providers and special distributors, not by Nokia. After inserting a card, leave it in the slot permanently . Do not re- move it again, unless you will be asked to do so. This is impor - tant because, for example, if your Service Provider wants to download new information to the smart card, the card has to be in the slot. Inserting the CA module with a smart card In the left slot you can use a CA module and a smart card from a service provider of your own choice. Insert the CA module and the smart card according to the instruc- tions provided with the module. CA module smart card About the smart card and CA module CA module smart card
GB 12 The box for your Mediamaster should contain the following items: •t he Mediamaster •r emote control with 2 AAA batteries • SCART cable (fully connected; 1,0 metre) • mains cable • RF cable • Owner’ s manual with software license agreement Connecting the Mediamaster About the SCART sockets The rear panel of the Mediamaster is equipped with 2 SCAR T sockets (see diagram). When you connect other devices to any of these sockets, always use fully connected SCART cables (as the one supplied.) There are SCART cables available which do not have all the pins connected. The picture quality could be reduced if you use them. SCART socket Preparing the remote control • Remove the cover on the battery compartment at the bottom of the remote control. •I nsert the 2 AAA; 1,5 V batteries, as shown in the diagram, tak- ing care to observe the and - markings indicated inside. • Replace the cover . SCART cable Mains cable Owner’ s Manual Remote control RF cable
GB 13 Connecting the Mediamaster Please note the following: • In some block of flats, the roof-mounted aerial system includes a filter and channel selector . If so, the aerial will probably not work with the Mediamaster . Please consult the landlord. •M any older roof-mounted aerials may only receive a limited number of channels. As a result, digital channels transmitted on higher frequencies are difficult or even impossible to re- ceive. The problem can be solved by replacing the roof aerial. • Some outdoor aerials are directed towards an analogue trans- mitter . The aerial must be directed towards a digital TV trans- mitter . • It is not always advisable to position the aerial as high as pos- sible. If problems arise, experiment with different aerial heights. 2. Indoor and window-mounted aerials This type of aerial may be enough if the reception conditions are very good. If an indoor aerial is used, please note the following: • Use an aerial for UHF channels 21 - 69, such as a directional aerial. •P lace the aerial by the window and directed towards the TV transmitter , if possible. • The Nokia aerial with an amplifier is recommended as it may provide a stronger signal. • The strength of the TV signal varies according to reflections from e. g. buildings. The signal penetrates thick stone or con- crete walls poorly . However , a wooden building is not a big bar - rier to digital TV signals. Connecting to the TV aerial Y ou can connect the Mediamaster to the following type of aerials: 1. Standard outdoor aerial Where possible, use an outdoor roof aerial intended for receiv- ing UHF channels between 21 and 69. About the digital transmission Digital Radio and TV signals can be blocked by buildings, moun- tains and the terrain. Depending on if the receiver is located in a depression in the ground, behind a mountain or in a concrete building, the quality of reception may vary considerably . Reflections can be used for reception by directing the aerial to- wards a mountain or a high building, providing that they do not block the transmitter . As with most other transmissions, bad weather does affect the reception quality negatively .
GB 14 Connecting the Mediamaster Connection of a video recorder • Connect a SCART cable between the main SCAR T socket on the TV and the TV SCART socket on the Mediamaster . • Connect an RF cable from the TV/VCR output on the Media- master to the RF input socket on the video. • Connect the TV aerial to the TV AERIAL input socket on the Mediamaster . • Connect an RF cable from the TV/VCR output on the video to the RF input socket on the TV . •C onnect a SCART cable between the TV SCAR T socket on the video and the AUX SCART socket on the Mediamaster SCART RF video Connecting the Mediamaster to the TV • Connect a SCART cable between the main SCAR T socket on the TV and the TV SCART socket on the Mediamaster . • Connect an RF cable from the TV/VCR output on the Media- master to the RF input socket on the TV . • Connect the TV aerial to the TV AERIAL input socket on the Mediamaster . SCART General There are many different types of TV/VCR and other equipment that you can connect to the Mediamaster . In this manual you will see some of the most common ways to connect your equipment. If you have problems with your connections and need help, con- tact your dealer .
GB 15 Connecting the Mediamaster Procedure when RF connections are used This procedure is necessary only when your Mediamaster is connected to the TV with an RF lead and no SCAR T leads are used. To tune your TV to the RF signal you might also need your TV manual in addition to this manual. The steps below explain what to do if you have been unable to use SCART leads in your con- nection. •P lug in your Mediamaster to the mains. T uning your TV to the Mediamaster • Select a programme number on the TV that is not currently used for other TV channels. • Follow the instructions in your TV manual to tune the TV chan- nel selector to UHF channel 43 (this is the Mediamaster’ s fac- tory preset UHF channel). • Follow the instructions in your TV manual to store this UHF chan- nel as the channel used by your Mediamaster . Y ou will have to select it when you want to watch terrestrial digital TV channels. • When the First time installation menu is visible, press the Select button on the Mediamasters remote control to start the installation procedure. If the picture quality is bad you can later change the predefined UHF channel 43 to any other figure between 21 and 69. Y ou will also have to tune your TV to the same (= the new) channel number . Please see RF modulator output channel setting on page 30. When you have a VCR connected it must be tuned to a different UHF channel (between 21 to 69) than the Mediamaster . Connecting a HiFi system • Connect an RCA/Cinch stereo cable from the AUDIO L R sock- ets on the Mediamaster to the LINE, AUX, SP ARE or EXTRA input sockets on your HiFi system. • If available you can connect an RCA/Cinch single cable from the DIGIT AL AUDIO socket on the Mediamaster to a HiFi sys- tem equipped with digital audio input. This output is also used for connection to an external Dolby™ digital decoder . Note: To avoid interference you must use screened audio ca- bles. Never connect digital output to any analog input. RF
GB 16 General information Once you have correctly connected the Mediamaster , you also have to perform a “First time installation.” During this procedure, helpful information is displayed at the bot- tom of the menus. Please note! The select button always confirms a selection within these menus, and pressing it will take you to the next step in the instal- lation process. However , and this is important, often more than one value has to be entered in a menu. First, perform all neces- sary settings on the different lines. Then, confirm them all simul- taneously by pressing select . Y ou can always go back to the previous menu by pressing back . Use cursor up / down to move upwards and downwards from one line to another . Use cursor left / right to change settings. Y ou can also use the numeric buttons on the remote control to enter numeric values. Switching on for the first time and start the “First time installation” •P lug in your Mediamaster • The ”First time installation” menu is shown. •P ress select to continue. Language • Select the desired menu language with cursor up/ down. This will also become the main language for audio and subti- tling. •W hen you now press select again to confirm your choice of language, you simultaneously start the searching for TV/Radio channels. First time installation
GB 17 First time installation Channel search in progress This menu will be shown as long as the Mediamaster is search- ing for TV and radio channels. All channels found will be listed on the screen. Please note that the search procedure may take a few minutes. Y ou can cancel the search at any time by pressing select . Ti me adjustment The time is adjusted by using cursor up / down , ± 1/2 an hour at a time. Y ou can also adjust the minutes by using cursor left / right. •P ress select to finish the first time installation and to open the Navi Bars. When the search procedure has ended, a message will tell how many TV and radio channels have been found. •P ress select to continue.
GB 18 V iewing mode Programme information Every time you change channels you will receive programme in- formation for a few seconds. (In the Control folder/User prefer - ences’ menu you can select how long this information will be shown.) The information may include: Current time. Channel list. Channel number and name. Name of the current and next programme. The start and stop time of the current programme. A bar , indicating the elapsed time of the current programme. The start and stop time of the next programme. Programme information will only be available if it is included in the transmission. Otherwise a “No information available” message will be shown. Information about the next programme Information about the current pro- gramme Name of channel list Current time Channel name and number General Information The following describes the basic functions of your Mediamaster while watching terrestrial digital TV . Some of the functions described here are dependent on the Service Provider and can only be used if they are included in the transmitted programme information. Please note , that during the Channel Search procedure, the Mediamaster may download a large number of channels. This may include channels from various Service Providers, also those to which you do not have access. If you select a programme to which you do not have access, you will get a message on the screen. In addition to the normal functions like switching the Media- master in/out of standby , changing the volume etc. there are some other useful functions which will be explained in this part of the manual. Y ou can always leave a menu at any time you want, without affecting any settings, by pressing the back button.
GB 19 V iewing mode Extended programme information The Mediamaster can display information about programmes cur - rently being broadcasted as well as those that will be broadcasted next. This procedure is the same for both TV and radio mode. By pressing info while watching TV you will get the “Programme information” banner . Press info again to display extended infor - mation about the current and the next programme. Use cursor left / right to switch between the current and the next pro- gramme information. When there is a lot of information text, use cursor up / down to continue reading on the next info page. Y ou cannot switch to another channel while the banner is visible. •P ress info or back to return to TV/radio mode. Te mporary settings By pressing opt you open a menu in which it is possible to enter temporary settings. Settings made in this “options menu” are only valid for the programme you currently are watching. If you leave the programme and return to it again, the temporary set- tings will be gone. Audio language When available, you can select among the different languages be- ing broadcast. Please note; When you select AC-3 there will be no sound output from the analogue audio connections. Subtitle language When available, you can select among different subtitle lan- guages. Picture format If you have a TV set with a 4:3 picture format, and the transmis- sion is in 16:9, you can select Fullscreen or Letterbox to change display format. Fullscreen will enlarge the centre of the picture to fill the screen. In this way some parts of the original programme contents will not be shown. Letterbox will give a complete picture, but leave black areas at the top and bottom. •P ress opt or back to return to TV/radio mode. letterbox fullscreen
GB 20 V iewing mode T eletext Pressing txt will open a teletext page (if teletext is transmitted.) Select teletext pages with the numeric buttons on the remote control. See figure 1. Y ou can also quickly go to the different page alternatives shown in any page by pressing cursor left / right. •P ress select on a highlighted page number to go to that page. • By pressing “ 0 ” you can alter between the two last pages you just have watched. • Press info to hide everything of a teletext page except its headline. See figure 2. • Sometimes a teletext page may contain subpages. When subpages are available, they are numbered in the lower part of the screen. See figure 3. T o view a subpage, press select when no page number is highlighted. Step to the different subpages with cursor left/right . Please note: It might take some time before all subpages are available for selection. •P ress txt/back to return to TV/radio mode. Cursor up / down will show the next or previous teletext page. On most new TV sets you can use the TV’ s remote control to open and control the teletext functions while watching digital TV channels. (The function is called VBI insertion.) External equipment Use the 0 (zero) button to toggle between the 230 T and any equipment connected to the AUX Scart; e. g. a Video recorder or a satellite receiver . Figure 1 Figure 2 Figure 3. Subpage numbers
GB 21 Navi Bars General information •P ress select to open the Navi Bars. In order to select TV and radio channels and to change system settings you will use the Navi Bars. The horizontal row contains folders , e. g. All TV , Settings and so on. Their names are shown with black text at the bottom of each folder . Each folder contains bookmarks. The All TV folder contains book- marks for the different TV channels; the Control folder contains bookmarks for some system settings and so on. Y ou move a folder horizontally by pressing cursor left/right . When a folder is moved to focus, the bookmarks will be shown in a vertical row . The name of the different bookmarks are shown with white text at the top of each bookmark. Y ou select a bookmark by pressing cursor up / down . T o confirm the selection, press select . Below the folder bar some information about the bookmark in focus is presented. When a TV or radio channel bookmark is in focus, this box can contain three different symbols after the chan- nel name: “ ” = new channel you have not previously visited. “ ” = channel is scrambled according to the service infor - mation. “ ” = channel is locked by the user . With a TV or radio programme bookmark in focus you can get programme information by pressing info . When you press opt you get a detailed channel information about the TV or radio programme bookmark in focus. When you press info with a bookmark from the control or set- tings folders in focus, you get more detailed information about what you can do in that menu. Y ou can leave the Navi Bars at any time by pressing back . If you open the Navi Bars and do not press any buttons on the remote control, the Navi Bars automatically closes after 2 minutes. Bookmark Bookmark in focus Information box Folder Folder name Bookmark name
GB 22 Navi Bars Banner T ime-out When you switch channels, an information banner will be shown for a few seconds. Y ou can select how long the banner will be shown. Vo lume bar Select whether or not you want the volume bar to appear on the screen when you change the volume. Vo lume bar time-out Select how long the volume bar will be visible on the screen. Subtitles Select whether or not subtitles will be visible on the screen. Main Subtitle Language If you select the “Visible” alternative for subtitling and mor e than one language is available, you may select a main language. Main Audio Language If more than one audio language is transmitted, you may select the main language. Menu Language Here you may select in which language the menus will be shown. Channel list icons In order to make the bookmark lists for TV and Radio channels shorter you can select to hide the icons and only show the chan- nel names. See figures to the right. Control folder ☛ User The “Control” and “Settings” folders Both of these system folders contains a few bookmarks. Each of these bookmarks contains menus from where you can make different settings. The system folders can not be deleted. The manual will now explain the different settings you can per - form from the Control and Settings folders, starting with the bookmarks from the Control folder . V isible Invisible
GB 23 Control folder ☛ Edit channels From these menus you can create and edit favourite channel lists. Y ou can add, delete, rename and arrange the order of the chan- nels within the favourite lists. The “All TV” list might contain lots of channels. B y creating your own favourite lists you can make channel handling more convenient. Important about editing channels Before you start you must select which list, TV or radio, you want to edit. When you are watching TV and press select and choose Edit channels, you can only edit TV channels. When you are listening to radio channels you can edit radio chan- nels. After the selection, radio or TV , use cursor left / right to select the name of the list to edit. Navi Bars Create list From here you create your own favourite lists, containing the channels you watch most frequently . Y ou must give each list a specific name, e.g. “Sport” or “Films”. The new lists you create will appear as a new folder in the horizontal part of the Navi Bars. When a favourite list is selected, you see only those channels de- fined in the list. When you have given the list a name; press select and choose “Add/Delete Channels” from the menu. Y ou can create separate favourite lists for TV and radio channels. How to give a specific name This procedure is the same whether you enter a name for the first time or change an existing. • Move to a new character position by using cursor left or cur - sor right . • If you enter a wrong character , you can remove it by pressing txt as many times as needed.
GB 24 • Enter the name as follows: Press the numerical button corresponding to the character you want: once for the first character , twice for the second and so on. The available characters are listed below . •I f the next letter is located on the same key as the present one, wait for the time-out or press cursor right to move one posi- tion and then select the letter . •T oggle between capital and lowercase letters with opt . •T o insert a space, press numerical button number 0 . 6 m n o 6 Ö Ô Ñ Ó Ò 7 p q r s 7 $ 9 w x y z 9 8 t u v 8 Ü Ù Ú 0 space 0 Navi Bars Rename list Y ou can give an existing list a new name by following the instruc- tions under the headline How to give a specific name , page 23. Delete list If you want to delete a favourite list completely , select the list with cursor left / right and press select . Rearrange lists If you have created several favourite lists you can determine the sequence in which the lists will appear . •W ith cursor right , mark the list you want to move to a new position. •M ove the list to the desired position with cursor up / down and press cursor left . •P ress select to confirm the new position. 1 * # & % $ , ! ; - ) / \ @ ^ 1 2 a b c 2 Å Ä Á Á Â C Ã 3 d e f 3 É É Ë Ê 4 g h i 4 Î Ï Í Ì 5 j k l 5
GB 25 Navi Bars Add/Delete channels From this menu you add and remove the channels in your favour - ite lists. Y ou use the “All TV” or “All radio” list as basis to select the channels from. A channel is added or removed from the list by pressing info. The square to the right on a line will be empty for removed channels, and will contain an “ x ” for added channels. Beside the channel name three different symbols can be shown. ( “ ” = a new chan- nel you have not previously visited. “ ” = the channel is scrambled according to the service information. “ ” = the chan- nel is locked by the user .) • Move to the desired channel(s) with cursor up/down. •P ress opt if you want to preview the channel. • Add/remove by pressing info. • When you are ready , confirm the selections and leave the menu by pressing select . Rearrange channels From here you can arrange the sequence for the channels within your favourite lists. • Move to the desired channel(s) with cursor up/down. •P ress opt if you want to preview the channel. •W ith cursor right , mark the channel you want to move to a new position within the list. •M ove the channel to the desired position with cursor up / down and press cursor left . •P ress select to confirm the new position. Lock channels To get to this menu you first have to enter your access code. From here you can lock (and later unlock) channels in order to pre- vent e.g. your children from watching. • Select the channel you want to lock and press info. Repeat the procedure for each channel you want to lock. •P ress opt if you want to preview the channel. •P ress select to confirm. A locked channel will be marked with a “ ” (padlock) symbol. Y ou must enter your access code before you can watch a locked channel.
GB 26 Navi Bars V iewing images received from an external device. (Bluetooth connection) General 230 T is equipped with a built in Bluetooth module that makes it possible to receive, watch and also save digital images transmit- ted from an external device. This device must be equipped with the Bluetooth Standard V ersion 1.1 and “Object Push Profile”. No cables are necessary as the transmission is wireless. The dis- tance between the transmitting device and the 230 T should not exceed 10 meters to ensure good transmission. Before the 230 T can start to receive images, some settings have to be made. Refer to Control folder ☛ Connections . About the Images folder in the Navi Bars Received images can be saved into a folder named Images . This folder will automatically be created in the Navi Bars as soon as you save your first picture. Y ou save a received image by press- ing select , delete it by pressing back . Y ou can watch images up to 256 Kbyte size. The Image folder can contain 36 images of max size 64 Kbyte/image. Please note that only JPEG images with VGA resolution of max. 640 x 480 pixels are supported. Images in the folder will be visible as “Thumbnails”. T o start watching an image, mark it in the Image folder and press select on the remote control. While watching an image you can select another by pressing cursor up/down . Y ou also have the possi- bility to delete the image you are watching by pressing opt, or all images by pressing txt. If you delete all images, also the Im- age folder will disappear from the Navi Bars. A new one will be created the next time you save an image. Y ou stop watching an image by pressing back . Control folder ☛ Connections Connectivity Ye s The Bluetooth function is enabled and the receiving of im- ages is possible. No The Bluetooth function is disabled and the receiving of im- ages is not possible. Selecting Ye s also means that the external device during its searching for a suitable Bluetooth receiver to send images to, should be able to find the 230 T . If it does not find it, the reason might be that No is selected.
GB 27 Navi Bars Local device name The 230 T is named Mediamaster on this line. This is also the name the external device will find during its search procedure. Y ou can enter another name with the number buttons on the re- mote control. Press any number button and a keyboard will be shown on the screen. How to enter a new name, please refer to page 23. Bluetooth passkey The very first time you want to send an image to the 230 T a pass- key has to be entered in the transmitting device. By default this passkey is set to 123456789 on this line. It is highly recom- mended to change it immediately . The length of the passkey must be at least 8 and max. 16 characters. The reason to change the key is, that if e.g. your neighbour also has a 230 T and neither you nor the neighbour has changed the 123456789, you may send pictures to each others boxes! Paired devices Will show how many external devices that have access to the box. Y ou can prevent all external devices from having access to the box by pressing info. T o get new access to the 230 T you have to enter the passkey again. Restrictions The Bluetooth products are not approved for use everywhere. Please check with the local authorities. That 230 T is equipped with the Bluetooth connectivity function is indicated on the T ype label on the underside of the box with the symbol shown below .
GB 28 Navi Bars Control folder ☛ T i m e r General Y ou can make the Mediamaster to start and stop at a predefined time. The timer function is very useful when you want to record a pro- gramme and you are unable to start/stop the recording event yourself, or when you just want to be reminded of the start of a programme you do not want to miss. Note! The timer function only works when the receiver is in standby . Ti mer setup •F irst, select Channel List with cursor left/right . • Then, step to Channel to select the desired TV/Radio channel. • Set the date using the numerical buttons on your remote con- trol (yy/mm/dd). • If you enter a wrong digit you can erase it with cursor left. • Set the start and stop time using the numerical buttons on your remote control. The different start times may never overlap each other . If you try to enter a start or stop time within an already occupied period of time you will get a warning message about it. •P ress select to save or back to cancel. •P ress back twice to leave the Navi Bars and return to view- ing mode. •P ress to put the Mediamaster in standby . Up to 8 different events can be predefined. The events will be sorted in start time order . At each stop time the box will return to standby . Y ou can erase a predefined event by pressing cursor right . • Press back to cancel the deletion and select to delete the event. Control folder ☛ System info If you have to contact your service provider or a service centre, they might ask for information available from this menu. In the menu you find general information about which hardware and software version your Mediamaster is running on.
GB 29 Navi Bars Settings folder ☛ Channel When you want to search for channels at a later time. T o open this menu you will be asked to enter your access code. From the factory the access code is set to 1234 . A channel search procedure can be performed in different ways: Automatic, Manual or Advanced manual search. Automatic search •H ighlight the line and press select to start searching for chan- nels. Manual search When you perform a Manual search you first need to enter some parameters for the channel search to work. The information you need to enter in this menu should be sup- plied by your Service provider . Channel : Select the channel you want to search for . Network search : Select “Y es” if you want to search on all trans- mitters connected to a specific network. •P ress select to start searching for channels. Advanced manual search The information you need to enter in this menu should be sup- plied by your Service provider . Y ou can use this menu if you ar e looking for some “specific” channels (i.e. non-DVB standard channels) which can be more easy to find when you have entered the necessary PID settings here. Channel: Select the channel you want to search for . PID Video : Enter the PID (Packet Identifier) for the video signal. PID Audio : Enter the PID for the audio signal. PID PCR : Enter the PID for the PCR (Programme Clock Refer - ence). •P ress select to tune with the specified values. All channels created with advanced manual search will get an automatically generated name, e.g. P0001 for the first channel, P0002 for the second etc. •P ress select to save the new channel or back if you do not want to save it.
GB 30 Navi Bars Settings folder ☛ T V To open this menu you will be asked to enter your access code. From the factory the access code is set to 1234 . From here you can adjust the audio/video settings for your Media- master . TV screen format Select your TV screen format. The 4:3 format is the standard format for most TV screens. Select 16:9 for a widescreen TV . Position of the RGB output Adjust the horizontal position of the TV picture with cursor left / right . T ransparency level Adjust the transparency level of the graphics in the menus by using cursor left / right . Digital audio format Select audio format for the digital output. (The upper audio output on the rear of the Mediamaster). AC-3 when the sound is transmitted in Dolby™ Digital format. PCM for ordinary digital sound. Please note; When you select AC-3 there will be no sound output from the analogue audio connections. Picture format If you have a TV set with the 4:3 picture format and the transmis- sion is in 16:9, you can select “Fullscreen” or “Letterbox”. Fullscreen will enlarge the centre of the picture to fill the screen. In this way some parts of the original programme contents will not be shown. Letterbox will give a complete picture, but leave black areas at the top and bottom. TV standard When the Mediamaster is connected to the TV by an RF cable, you may need to select the correct TV standard system. Select P AL G when the box is used outside the UK and France. Select P AL I when the box is used inside the UK. Select SECAM when the box is used in France. RF modulator output channel Select this alternative if you have to change the RF channel. (Channel 43 is preset from factory .) Select another RF output channel number from the right part of the RF modulator output channel line. Channels found during the first time installation will not be able to select. When you change the RF channel number , you must also change to the same value on the TV . If you do not, there will be no pic- ture and sound. letterbox fullscreen
GB 31 Navi Bars Settings folder ☛ Access To open this menu you will be asked to enter your access code. From the factory the access code is set to 1234 . The following settings can be altered from this menu. Access Control Select “Y es” or “No” to turn the access control in all menus on or off. Note: Even when “No” is selected, the access code still has to be entered before you can watch locked channels. Receiver lock If you select “Y es” you will have to enter the access code every time you start the Mediamaster from standby . Age rating control If you want everybody to have access to all available types of pro- grammes, select “No” If you select “Y es” you may block programmes unsuitable for chil- dren. Age Limit Select an age limit between 3 and 18 years on the line that ap- pears. However , you should be aware that not all Service Providers have the necessary codes for these functions implemented in their transmissions. Change access code From here you can change the access code from the stand- ard 1234. DO NOT FORGET IT! Without it you do not have ac- cess to any of the functions where the code is required! If you forget it, you have to contact an Authorised Nokia Service Centre to get help. Settings folder ☛ T i m e To open this menu you will be asked to enter your access code. From the factory the access code is set to 1234 . The time is adjusted by using cursor up / down , ± 1/2 an hour at a time. Y ou can also adjust the minutes by using cursor left / right.
GB 32 Navi Bars Games folder •W hen the Games folder is in focus, select a game and press info to get instructions how to play it. •P ress select to start a game. •P ress back to finish a game. Settings folder ☛ Reinstall Use this option only if you have to start the complete installation procedure from scratch. If you continue from here, all your pre- vious settings, access code and favourite channels etc. will be erased! If you do not want to perform a reinstallation you can leave this menu when the warning is displayed by pressing “back”. Settings folder ☛ SW update In order to keep the Mediamaster up-to-date, it will be possible to download new versions of the system software (SW). New software may include new or improved features for existing menus. Enter this menu to check for new software. If new software is available you will get information in the menu on how to proceed. Y ou may have to select a specific channel in order to download new software. If you select to download a new software version, all your previ- ous settings, access code and favourite channels etc. will be erased! IMPORT ANT! The updating may take a while. NEVER turn off the Mediamaster , never use the remote con- trol or disconnect the antenna cable during the download procedure! This will damage the software and the receiver will have to be sent in for service!
GB 33 PCR Program Clock Reference. PID Packet Identifier . RCA Coaxial connector used to connect the Mediamaster to an external amplifier . RF Radio frequency (known as HF in some countries). RGB Red, Green, Blue. Colour signals are routed in separate cables in order to provide a high quality TV picture. SERIAL RS 232 A serial communication standard data port. SCART A 21-pin connector used for connection of the Media- master , VCR and TV . Also named Euroconnector or Peritel connector . Scrambled TV programme Some TV programmes are transmitted in scrambled form. Service provider Is a company that collects a number of programmes/serv- ices and distributes them to customers. S/PDIF Sony/Philips digital interface format. Digital audio output. Symbol rate Speed of the digital transmission SW Software. Programme code. TS T ransport stream. VCR Vi deo Cassette Recorder . AC-3 Multichannel digital audio encoding system. Access code A four -digit code stored in the Mediamaster . Used to lock/unlock the Mediamaster . Access control A feature that allows parents to ”lock” programmes that they consider unsuitable for children. A ”locked” chan- nel or programme can only be ”unlocked” with the spe- cial access code. AGC Automatic Gain Control. BER Bit Error Rate. Signal quality measure. C/N Carrier to Noise. Signal quality measure DVB The Digital Video Broadcast group was created to estab- lish a technical framework for the introduction of digital video broadcasting systems. GHz The prefix giga means milliard, and Hertz means cycles per second. Signals in the GHz range are often called mi- crowaves. MHz The prefix mega means million, and Hertz means cycles per second. MPEG Moving Picture Experts Group. Established by the Inter - national Standards Organisation to provide the basis for a picture coding and compression system. Network A number of digital channels transmitted from one source. PCM Pulse Code Modulation. Non-compressed digital audio format. Glossary
GB 34 What to do Check that the mains cable is plugged into the power socket. Press the standby button to bring the Mediamaster out of standby mode. Change both batteries. Aim the remote control at box. Check that nothing blocks the front panel. Contact your Service Provider . They will help you set it up again. Check the aerial installation including its connections. Check if you can receive and watch analogue channels from the transmit- ter . Check that the aerial is directed to- wards the transmitter . Check that digital transmissions are available in the area. If things does not work out as they should, let the local TV dealer check whether the aerial is intended for re- ceiving digital transmissions or not. If not, you have to exchange the aerial. When the system is connected by SCAR T cables the TV must be set in A V/EXT mode. Tr oubleshooting Problem The LED on the front panel does not light up/is not lit. The left LED is shining red The remote control is not working. Y ou have forgotten your PIN code. During the first time installation when the Mediamaster tries to find and store channels you get the message “No channels found”. When only very few of the ex- pected number of channels are found. There is no First time installation menu on the screen when you switch on the Mediamaster for the first time. Possible causes Mains cable is not connected. The Mediamaster is in standby mode. Battery exhausted. Remote control is incorrectly aimed. The aerial is not properly connected to the Mediamaster . The aerial is not correctly directed towards the transmitter . The aerial is not suitable for digital channels. The signal is to weak for the con- nected aerial. There are no terrestrial digital trans- missions in the area. The system is connected by SCAR T cables and the TV is not in A V/EXT mode. What to do if you can’ t solve the problem? If you have tried all of the actions suggested above, without solving the problem, please contact your dealer or Service Provider .
GB 35 T echnical specifications T ransmission Standards DVB, MPEG 2, OFDM Input/output Input connector IEC female RF input frequency 174-300; 474-862 MHz RF input power level -78 to -30 dBm RF impedance 75 Ω Frequency range Loop through 47-862MHz Frequency range RF modulator 470-862 MHz Output channel CH 21-69 Preset channel 43 Output signal P AL G, I, SECAM Demodulation Supports 2k and 8k TV SCART Vi deo output 1 V pp ( ± 1 dB) / 75 Ω Audio output 0.5 V rms / R L >10 k Ω RGB output Internal RGB RGB bandwidth 5.8 MHz ± 3 dB Fast blanking output Internal Status output 0/6/12 V / R L 10 k Ω AUX SCART Vi deo output 1 V pp ( ± 1 dB) / 75 Ω Vi deo input 1 V pp / 75 Ω Audio output 0.5 V rms / R L >10 k Ω Audio input 0.5 V r ms / R L >10 k Ω Status input 0/6/12 V / R L >10 k Ω DIGIT AL AUDIO (S/PDIF) Connector 1 x RCA AUDIO R L Connector 2 x RCA (R L) Output 0.5 V rms ± 0.5 dB/ R L 10 k Ω SERIAL (RS 232) Serial data Connector 9-pin D-sub male Signals RS232, max. 115,2 kbit/s Pin 1 DCD (Data carrier detect) not connected 2 RXD (Receive data) 3 TXD (T ransmit data) 4 DTR (Data terminal ready) Set to high 5 GND (Signal ground) 6 DSR (Data set ready) not connected 7 RTS (Ready to send) 8 CTS (Clear to send) 9 RI (Ring indicator) not connected Front panel Tw o LED; Buttons: , ▼ ▲ General data The model code, variant and serial number , are located on a label on the underside of the housing. Supply voltage 110-240 V AC, 50-60 Hz Power consumption max 10 W Power consumption in standby 5 W Operating temperature 5 ° C to 45 ° C Storage temperature - 40 ° C to 65 ° C Humidity 25 to 75 % rel. humidity Operating distance for remote control About 10 meters Dimensions (w x d x h) 250 x 275 x 80 mm We ight 1050 g. approx. 1 21 2 20 SCART sockets TV AUX 1 Audio out right ch. Audio out right ch. 2 - Audio in right ch. 3 Audio out left ch. Audio out left ch. 4 Audio ground Audio ground 5 RGB blue ground - 6- Audio in left ch. 7 RGB blue signal out - 8S witch voltage out Switch voltage in 9 RGB green ground - 10 Connect to pin 10 in AUX scart 11 RGB green signal out - 12 - - 13 RGB red ground - 14 Fast blank. ground Fast blank. ground 15 RGB red signal out - 16 Fast blanking out - 17 Video out ground Video out ground 18 - Video in ground 19 Video out V ideo out 20 - V ideo in 21 Ground (casing) Ground (casing)
Nokia is a registered trademark of Nokia Corporation www .nokia.com 00002958.00