Philips CED750 Quick Start Manual
Register your product and get support at CED750 ENG Quick Start Guide 2 183 mm 53.5 mm 5mm 1 1 2 3 4 5 6 7 8 9 0 ! CED750 QSG_Eng.indd 1 CED750 QSG_Eng.indd 1 2008-12-12 16:05:21 2008-12-12 16:05:21
English Connect wires: ISO connectors 1 Pull out the ISO connectors from the car dashboard and connect them to the bigger end of the supplied standard connector . 2 Connect the other end of supplied standard connector to the unit. If necessar y , connect the following: ⢠Connector Connect to/with 1 Black cable Antenna 2 Y ellow cable Video out 1 3 Y ellow cable Video out 2 4 Y ellow cable Camera in 5 Green/white wire Parking 6 Black cable Bluetooth microphone 7 Blue cable Subwoofer 8 Red cable Front line out L 9 White cable Front line out R 0 Red cable Rear line out L ! white cable Rear line out R Mount in the dashboard Note Check wire connection before you mount ⢠the unit into a car . If preset radio stations are lost when the ⢠ignition key is turned OFF and then back ON, reconnect the red leads crosswise to the yellow ones. 1 If the car does not have an on-board drive or navigation computer , disconnect the negative terminal of the car batter y . If you disconnect the car battery in ⢠a car that has an on-board drive or navigation computer , the computer may lost its memor y . If the car batter y is not disconnected, ⢠to avoid short-circuit, ensure that bare wires do not touch each other . 2 Ensure that car dashboard opening is within these measurements: Since the unit cannot be used if the ⢠dashboard openingâÂÂs slant angle is abo ve 20 degrees: Ensure that the horizontal slant of the car dashboard opening is between 0 and 20 degrees 3 Remove the screws on the both side of the unit. 4 Remove the mounting sleeve. 5 Install the sleeve into the dashboard and bend the tabs outward to ﬠx the sleeve. 6 Place the rubber cushion over the end of the bolt. 7 Slide the unit into the dashboard until a click sound is heard. If the unit cannot ﬠt into the dashboard, ⢠remove the mounting bracket on the both side of the unit and replace them with the supplied shor t mounting brackets. 8 Attach the trim plate. 9 Reconnect the negative terminal of the car batter y . T urn on 1 Press the to turn on the unit. The screen opens automatically . û The available OSD (On-Screen Display) û languages are displayed. 2 T ouch a language to select. The OSD language is changed to the û selected language immediately . T o adjust the screen tilt, press ⢠TIL T . T o close the screen, press ⢠OPEN/CLOSE . T o adjust the br ightness/contrast, press ⢠/ , then adjust 4 W A Y NA VIGA TION . T o tur n off the system, press ⢠for 3 sec- onds. The screen closes automatically . û Set clock 1 T ouch to display main menu. 2 T ouch [Setting] . The setup menu is displayed. û 3 T ouch [General] . 4 T ouch the [Clock mode] repeatedly to select: [12hr] ⢠: 12 hour mode [ ⢠24hr] : 24 hour mode 5 T ouch the hour digits, then touch or . 6 T ouch the minute digits, then touch or . 7 If 12 hour mode is selected, touch or to select AM or PM . 8 T ouch to exit. T une to a radio station 1 T ouch to display the main menu. 2 T ouch [Radio] . Band and frequency information is û displayed. 3 T ouch [Band] repeatedly to select: FM band options: ⢠FM1 , FM2 , FM3 AM band options: ⢠AM1 , AM2 4 Brie ﬠy touch [Previous] or [Next] to tune to a radio station by step. Pla y discs 1 Inser t the disc into the disc slot with label side facing up. Play star ts automatically . û T o remove the disc, press the û button. When the disc is ejected, the unit switches û to the previous source, if connected. Other- wise, the unit switches to [Radio] mode auto- matically . Insert USB or SD/MMC card 1 Open the USB/SD/MMC card cover . 2 Inser t the USB device or SD/MMC card into the USB socket or SD/MMC card slot. Play star ts automatically . û Pair the Bluetooth-enabled devices 1 T urn on the Bluetooth function on the device. 2 Setup the Bluetooth function on your device. 3 Select âÂÂCED750â in the pairing list. 4 Enter default password âÂÂ0000âÂÂ. iI pairing succeeds. û [Connect] is displayed on the panel. Make a call 1 Pair the phone with the system. 2 T ouch to retur n to main menu. 3 T ouch [Bluetooth]. The Bluetooth menu is displayed. û 4 T ouch to dial. Receive call 1 If there is incoming call, [Incoming callâ¦] ﬠashes on the screen. Speak into the Blue- tooth microphone. 2 When conversation ends, touch to terminate the call. 3 P r i n t i n g i n C h i n a P r i n t i n g i n C h i n a 4 é 2008 Koninklijk e Philips Electronics N.V . All rights reserved. CED750 QSG_Eng.indd 2 CED750 QSG_Eng.indd 2 2008-12-12 16:05:30 2008-12-12 16:05:30
English Connect wires: ISO connectors 1 Pull out the ISO connectors from the car dashboard and connect them to the bigger end of the supplied standard connector . 2 Connect the other end of supplied standard connector to the unit. If necessar y , connect the following: ⢠Connector Connect to/with 1 Black cable Antenna 2 Y ellow cable Video out 1 3 Y ellow cable Video out 2 4 Y ellow cable Camera in 5 Green/white wire Parking 6 Black cable Bluetooth microphone 7 Blue cable Subwoofer 8 Red cable Front line out L 9 White cable Front line out R 0 Red cable Rear line out L ! white cable Rear line out R Mount in the dashboard Note Check wire connection before you mount ⢠the unit into a car . If preset radio stations are lost when the ⢠ignition key is turned OFF and then back ON, reconnect the red leads crosswise to the yellow ones. 1 If the car does not have an on-board drive or navigation computer , disconnect the negative terminal of the car batter y . If you disconnect the car battery in ⢠a car that has an on-board drive or navigation computer , the computer may lost its memor y . If the car batter y is not disconnected, ⢠to avoid short-circuit, ensure that bare wires do not touch each other . 2 Ensure that car dashboard opening is within these measurements: Since the unit cannot be used if the ⢠dashboard openingâÂÂs slant angle is abo ve 20 degrees: Ensure that the horizontal slant of the car dashboard opening is between 0 and 20 degrees 3 Remove the screws on the both side of the unit. 4 Remove the mounting sleeve. 5 Install the sleeve into the dashboard and bend the tabs outward to ﬠx the sleeve. 6 Place the rubber cushion over the end of the bolt. 7 Slide the unit into the dashboard until a click sound is heard. If the unit cannot ﬠt into the dashboard, ⢠remove the mounting bracket on the both side of the unit and replace them with the supplied shor t mounting brackets. 8 Attach the trim plate. 9 Reconnect the negative terminal of the car batter y . T urn on 1 Press the to turn on the unit. The screen opens automatically . û The available OSD (On-Screen Display) û languages are displayed. 2 T ouch a language to select. The OSD language is changed to the û selected language immediately . T o adjust the screen tilt, press ⢠TIL T . T o close the screen, press ⢠OPEN/CLOSE . T o adjust the br ightness/contrast, press ⢠/ , then adjust 4 W A Y NA VIGA TION . T o tur n off the system, press ⢠for 3 sec- onds. The screen closes automatically . û Set clock 1 T ouch to display main menu. 2 T ouch [Setting] . The setup menu is displayed. û 3 T ouch [General] . 4 T ouch the [Clock mode] repeatedly to select: [12hr] ⢠: 12 hour mode [ ⢠24hr] : 24 hour mode 5 T ouch the hour digits, then touch or . 6 T ouch the minute digits, then touch or . 7 If 12 hour mode is selected, touch or to select AM or PM . 8 T ouch to exit. T une to a radio station 1 T ouch to display the main menu. 2 T ouch [Radio] . Band and frequency information is û displayed. 3 T ouch [Band] repeatedly to select: FM band options: ⢠FM1 , FM2 , FM3 AM band options: ⢠AM1 , AM2 4 Brie ﬠy touch [Previous] or [Next] to tune to a radio station by step. Pla y discs 1 Inser t the disc into the disc slot with label side facing up. Play star ts automatically . û T o remove the disc, press the û button. When the disc is ejected, the unit switches û to the previous source, if connected. Other- wise, the unit switches to [Radio] mode auto- matically . Insert USB or SD/MMC card 1 Open the USB/SD/MMC card cover . 2 Inser t the USB device or SD/MMC card into the USB socket or SD/MMC card slot. Play star ts automatically . û Pair the Bluetooth-enabled devices 1 T urn on the Bluetooth function on the device. 2 Setup the Bluetooth function on your device. 3 Select âÂÂCED750â in the pairing list. 4 Enter default password âÂÂ0000âÂÂ. iI pairing succeeds. û [Connect] is displayed on the panel. Make a call 1 Pair the phone with the system. 2 T ouch to retur n to main menu. 3 T ouch [Bluetooth]. The Bluetooth menu is displayed. û 4 T ouch to dial. Receive call 1 If there is incoming call, [Incoming callâ¦] ﬠashes on the screen. Speak into the Blue- tooth microphone. 2 When conversation ends, touch to terminate the call. 3 P r i n t i n g i n C h i n a P r i n t i n g i n C h i n a 4 é 2008 Koninklijk e Philips Electronics N.V . All rights reserved. CED750 QSG_Eng.indd 2 CED750 QSG_Eng.indd 2 2008-12-12 16:05:30 2008-12-12 16:05:30