Philips PiP3209-R Product Specification
Philips Semiconductors Product Specification TOPFET high side switch PiP3209-R DESCRIPTION QUICK REFERENCE DATA Monolithic single channel high side SYMBOL PARAMETER MIN. UNIT protected power switch in TOPFET2 technology assembled in I L Nominal load current (ISO) 2 A a 5 pin plastic surface mount package. SYMBOL PARAMETER MAX. UNIT APPLICATIONS V BG Continuous off-state supply voltage 50 V General controller for driving I L Continuous load current 6 A lamps, motors, solenoids, heaters. T j Continuous junction temperature 150 ÃÂC R ON On-state resistance T j = 25ÃÂC 180 m ⦠FEATURES FUNCTIONAL BLOCK DIAGRAM Vertical power TrenchMOS Low on-state resistance CMOS logic compatible Very low quiescent current Overtemperature protection Load current limiting Latched overload and short circuit protection Overvoltage and undervoltage shutdown with hysteresis On-state open circuit load detection Diagnostic status indication Voltage clamping for turn off of inductive loads ESD protection on all pins Reverse battery, overvoltage and transient protection Fig.1. Elements of the TOPFET HSS with internal ground resistor. PINNING - SOT426 PIN CONFIGURATION SYMBOL PIN DESCRIPTION 1 Ground 2 Input 3 (connected to mb) 4 Status 5 Load Fig. 2. Fig. 3. mb Battery BATT LOAD INPUT GROUND STATUS POWER MOSFET RG CONTROL & PROTECTION CIRCUITS mb 12 4 5 3 B G L I S HSS TOPFET July 2001 1 Rev 1.000
Philips Semiconductors Product Specification TOPFET high side switch PIP3209-R LIMITING VALUES Limiting values in accordance with the Absolute Maximum System (IEC 134) SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT V BG Continuous supply voltage 0 50 V I L Continuous load current T mb ⤠114ÃÂC - 6 A P D Total power dissipation T mb ⤠25ÃÂC - 41 W T stg Storage temperature -55 175 ÃÂC T j Continuous junction temperature 1 - 150 ÃÂC T sold Mounting base temperature during soldering - 260 ÃÂC Reverse battery voltages 2 -V BG Continuous reverse voltage - 16 V -V BG Peak reverse voltage - 32 V Application information R I , R S External resistors 3 to limit input, status currents 3.2 - k ⦠Input and status I I , I S Continuous currents -5 5 mA I I , I S Repetitive peak currents ô ⤠0.1, tp = 300 õs -50 50 mA Inductive load clamping I L = 1 A, V BG = 16 V E BL Non-repetitive clamping energy T j = 150ÃÂC prior to turn-off - 75 mJ ESD LIMITING VALUE SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT V C Electrostatic discharge capacitor Human body model; - 2 kV voltage C = 250 pF; R = 1.5 k ⦠THERMAL CHARACTERISTICS SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Thermal resistance 4 R th j-mb Junction to mounting base - - 2.5 3 K/W 1 For normal continuous operation. A higher T j is allowed as an overload condition but at the threshold T j(TO) the over temperature trip operates to protect the switch. 2 Reverse battery voltage is allowed only with external resistors to limit the input and status currents to a safe value. The connected load must limit the reverse load current. The internal ground resistor limits the reverse battery ground current. Power is dissipated and the T j rating must be observed. 3 To limit currents during reverse battery and transient overvoltages (positive or negative). 4 Of the output power MOS transistor. July 2001 2 Rev 1.000
Philips Semiconductors Product Specification TOPFET high side switch PIP3209-R STATIC CHARACTERISTICS Limits are at -40ÃÂC ⤠T mb ⤠150ÃÂC and typicals at T mb = 25 ÃÂC unless otherwise stated. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Clamping voltages V BG Battery to ground I G = 1 mA 50 55 65 V V BL Battery to load I L = I G = 1 mA 50 55 65 V -V LG Negative load to ground I L = 10 mA 18 23 28 V -V LG Negative load voltage 1 I L = 1 A; t p = 300 õ s2 0 2 5 3 0 V Supply voltage battery to ground V BG Operating range 2 - 5.5 - 35 V Currents 9 V ⤠V BG ⤠16 V I B Quiescent current 3 V LG = 0 V - - 20 õA T mb = 25ÃÂC - 0.1 2 õA I L Off-state load current 4 V BL = V BG -- 2 0 õ A T mb = 25ÃÂC - 0.1 1 õA I G Operating current 5 I L = 0 A - 2 4 mA I L Nominal load current 6 V BL = 0.5 V 2 - - A Resistances V BG I L t p T mb R ON On-state resistance 7 9 to 35 V 1 A 300 õs 25ÃÂC - 135 180 m ⦠150ÃÂC - - 330 m ⦠R ON On-state resistance 6 V 1 A 300 õs 25ÃÂC - 170 225 m ⦠150ÃÂC - - 410 m ⦠R G Internal ground resistance I G = 10 mA 95 150 190 ⦠1 For a high side switch, the load pin voltage goes negative with respect to ground during the turn-off of an inductive load. 2 On-state resistance is increased if the supply voltage is less than 9 V. 3 This is the continuous current drawn from the supply when the input is low and includes leakage current to the load. 4 The measured current is in the load pin only. 5 This is the continuous current drawn from the supply with no load connected, but with the input high. 6 Defined as in ISO 10483-1. For comparison purposes only. 7 The supply and input voltage for the R ON tests are continuous. The specified pulse duration t p refers only to the applied load current. July 2001 3 Rev 1.000
Philips Semiconductors Product Specification TOPFET high side switch PIP3209-R INPUT CHARACTERISTICS 9 V ⤠V BG ⤠16 V. Limits are at -40ÃÂC ⤠T mb ⤠150ÃÂC and typicals at T mb = 25 ÃÂC unless otherwise stated. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT I I Input current V IG = 5 V 20 90 160 õA V IG Input clamping voltage I I = 200 õA 5.5 7 8.5 V V IG(ON) Input turn-on threshold voltage - 2.4 3 V V IG(OFF) Input turn-off threshold voltage 1.5 2.1 - V â V IG Input turn-on hysteresis - 0.3 - V I I(ON) Input turn-on current V IG = 3 V - - 100 õA I I(OFF) Input turn-off current V IG = 1.5 V 10 - - õA STATUS CHARACTERISTICS The status output is an open drain transistor, and requires an external pull-up circuit to indicate a logic high. Limits are at -40ÃÂC ⤠T mb ⤠150ÃÂC and typicals at T mb = 25 ÃÂC unless otherwise stated. Refer to TRUTH TABLE. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT V SG Status clamping voltage I S = 100 õA 5.5 7 8.5 V V SG Status low voltage I S = 100 õ A- - 1 V T mb = 25ÃÂC - 0.7 0.8 V I S Status leakage current V SG = 5 V - - 15 õA T mb = 25ÃÂC - 0.1 1 õA I S Status saturation current 1 V SG = 5 V 2 7 12 mA Application information R S External pull-up resistor - 47 - k ⦠OPEN CIRCUIT DETECTION CHARACTERISTICS An open circuit load can be detected in the on-state. Refer to TRUTH TABLE. Limits are at -40ÃÂC ⤠T mb ⤠150ÃÂC and typical is at T mb = 25 ÃÂC. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Open circuit detection 9 V ⤠V BG ⤠35 V I L(TO) Low current detect threshold 50 - 340 mA T j = 25ÃÂC 85 170 255 mA â I L(TO) Hysteresis - 30 - mA 1 In a fault condition with the pull-up resistor short circuited while the status transistor is conducting. This condition should be avoided in order to prevent possible interference with normal operation of the device. July 2001 4 Rev 1.000
Philips Semiconductors Product Specification TOPFET high side switch PIP3209-R UNDERVOLTAGE & OVERVOLTAGE CHARACTERISTICS Limits are at -40ÃÂC ⤠T mb ⤠150ÃÂC and typicals at T mb = 25 ÃÂC. Refer to TRUTH TABLE. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Undervoltage V BG(UV) Low supply threshold voltage 1 2 4.2 5.5 V â V BG(UV) Hysteresis - 0.5 - V Overvoltage V BG(OV) High supply threshold voltage 2 40 45 50 V â V BG(OV) Hysteresis - 1 - V TRUTH TABLE ABNORMAL CONDITIONS DETECTED LOAD INPUT SUPPLY LOAD OUTPUT STATUS DESCRIPTION UV OV LC SC OT L X X X X X OFF H off H 0 0 0 0 0 ON H on & normal H 0 0 1 0 0 ON L on & low current detect H 1 0 X X X OFF H supply undervoltage lockout H 0 1 X 0 0 OFF H supply overvoltage shutdown H 0 0 0 1 X OFF L SC tripped H 0 0 0 0 1 OFF L OT shutdown 3 KEY TO ABBREVIATIONS L logic low UV undervoltage H logic high OV overvoltage X donâÂÂt care LC low current or open circuit load 0 condition not present SC short circuit 1 condition present OT overtemperature 1 Undervoltage sensor causes the device to switch off and reset. 2 Overvoltage sensor causes the device to switch off to protect its load. 3 The status will continue to indicate OT (even if the input goes low) until the device cools below the reset threshold. Refer to OVERLOAD PROTECTION CHARACTERISTICS . July 2001 5 Rev 1.000
Philips Semiconductors Product Specification TOPFET high side switch PIP3209-R OVERLOAD PROTECTION CHARACTERISTICS 5.5 V ⤠V BG ⤠35 V, limits are at -40ÃÂC ⤠T mb ⤠150ÃÂC and typicals at T mb = 25 ÃÂC unless otherwise stated. Refer to TRUTH TABLE. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Overload protection V BL = V BG I L(lim) Load current limiting V BG âÂÂ¥ 9 V 6 9 12 A Short circuit load protection V BL(TO) Battery load threshold voltage 1 V BG = 16 V 8 10 12 V V BG = 35 V 15 20 25 V t d sc Response time 2 V BL > V BL(TO) - 180 250 õs Overtemperature protection T j(TO) Threshold junction 150 170 190 ÃÂC temperature 3 â T j(TO) Hysteresis - 10 - ÃÂC SWITCHING CHARACTERISTICS T mb = 25 ÃÂC, 9 V ⤠V BG ⤠16 V, for resistive load R L = 13 â¦. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT During turn-on to V IG = 5 V t d on Delay time to 10% V L -2 8 4 0 õ s dV/dt on Rate of rise of load voltage 30% to 70% V L - 0.75 1 V/ õs t on Total switching time to 90% V L -6 0 9 0 õ s During turn-off to V IG = 0 V t d off Delay time to 90% V L -3 6 5 4 õ s dV/dt off Rate of fall of load voltage 70% to 30% V L - 0.75 1 V/ õs t off Total switching time to 10% V L -6 0 9 0 õ s CAPACITANCES T mb = 25 ÃÂC; f = 1 MHz; V IG = 0 V. designed in parameters. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT C ig Input capacitance V BG = 13 V - 15 20 pF C bl Output capacitance V BL = 13 V - 100 140 pF C sg Status capacitance V SG = 5 V - 11 15 pF 1 The battery to load threshold voltage for short circuit protection is proportional to the battery supply voltage. After short circuit protection has operated, the input voltage must be toggled low for the switch to resume normal operation. 2 Measured from when the input goes high. 3 After cooling below the reset temperature the switch will resume normal operation. July 2001 6 Rev 1.000
Philips Semiconductors Product Specification TOPFET high side switch PIP3209-R MECHANICAL DATA Fig.4. SOT426 surface mounting package 1 , centre pin connected to mounting base. REFERENCES OUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC EIAJ SOT426 0 2.5 5 mm scale Plastic single-ended surface mounted package (Philips version of D 2 -PAK); 5 leads (one lead cropped) SOT426 e e e e E b A 1 A A 1 L p bc D max. e A UNIT DIMENSIONS (mm are the original dimensions) E 11 mm 4.50 4.10 1.40 1.27 0.85 0.60 0.64 0.46 2.90 2.10 H D 15.80 14.80 Q 2.60 2.20 10.30 9.70 D 1 1.60 1.20 1.70 98-12-14 99-06-25 1 3 24 5 mounting base D 1 H D D Q L p c 1 Epoxy meets UL94 V0 at 1/8". Net mass: 1.5 g. For soldering guidelines and SMD footprint design, please refer to Data Handbook SC18. July 2001 7 Rev 1.000
Philips Semiconductors Product Specification TOPFET high side switch PIP3209-R DEFINITIONS DATA SHEET STATUS DATA SHEET PRODUCT DEFINITIONS STATUS 1 STATUS 2 Objective data Development This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice Preliminary data Qualification This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in ordere to improve the design and supply the best possible product Product data Production This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Changes will be communicated according to the Customer Product/Process Change Notification (CPCN) procedure SNW-SQ-650A Limiting values Limiting values are given in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of this specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. ï Philips Electronics N.V. 2001 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, it is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. 1 Please consult the most recently issued datasheet before initiating or completing a design. 2 The product status of the device(s) described in this datasheet may have changed since this datasheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. July 2001 8 Rev 1.000
Philips Semiconductors Product Specification TOPFET high side switch PIP3209-R LIMITING VALUES Limiting values in accordance with the Absolute Maximum System (IEC 134) SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT V BG Continuous supply voltage 0 50 V I L Continuous load current T mb ⤠114ÃÂC - 6 A P D Total power dissipation T mb ⤠25ÃÂC - 41 W T stg Storage temperature -55 175 ÃÂC T j Continuous junction temperature 1 - 150 ÃÂC T sold Mounting base temperature during soldering - 260 ÃÂC Reverse battery voltages 2 -V BG Continuous reverse voltage - 16 V -V BG Peak reverse voltage - 32 V Application information R I , R S External resistors 3 to limit input, status currents 3.2 - k ⦠Input and status I I , I S Continuous currents -5 5 mA I I , I S Repetitive peak currents ô ⤠0.1, tp = 300 õs -50 50 mA Inductive load clamping I L = 1 A, V BG = 16 V E BL Non-repetitive clamping energy T j = 150ÃÂC prior to turn-off - 75 mJ ESD LIMITING VALUE SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT V C Electrostatic discharge capacitor Human body model; - 2 kV voltage C = 250 pF; R = 1.5 k ⦠THERMAL CHARACTERISTICS SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Thermal resistance 4 R th j-mb Junction to mounting base - - 2.5 3 K/W 1 For normal continuous operation. A higher T j is allowed as an overload condition but at the threshold T j(TO) the over temperature trip operates to protect the switch. 2 Reverse battery voltage is allowed only with external resistors to limit the input and status currents to a safe value. The connected load must limit the reverse load current. The internal ground resistor limits the reverse battery ground current. Power is dissipated and the T j rating must be observed. 3 To limit currents during reverse battery and transient overvoltages (positive or negative). 4 Of the output power MOS transistor. July 2001 2 Rev 1.000
Philips Semiconductors Product Specification TOPFET high side switch PIP3209-R STATIC CHARACTERISTICS Limits are at -40ÃÂC ⤠T mb ⤠150ÃÂC and typicals at T mb = 25 ÃÂC unless otherwise stated. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Clamping voltages V BG Battery to ground I G = 1 mA 50 55 65 V V BL Battery to load I L = I G = 1 mA 50 55 65 V -V LG Negative load to ground I L = 10 mA 18 23 28 V -V LG Negative load voltage 1 I L = 1 A; t p = 300 õ s2 0 2 5 3 0 V Supply voltage battery to ground V BG Operating range 2 - 5.5 - 35 V Currents 9 V ⤠V BG ⤠16 V I B Quiescent current 3 V LG = 0 V - - 20 õA T mb = 25ÃÂC - 0.1 2 õA I L Off-state load current 4 V BL = V BG -- 2 0 õ A T mb = 25ÃÂC - 0.1 1 õA I G Operating current 5 I L = 0 A - 2 4 mA I L Nominal load current 6 V BL = 0.5 V 2 - - A Resistances V BG I L t p T mb R ON On-state resistance 7 9 to 35 V 1 A 300 õs 25ÃÂC - 135 180 m ⦠150ÃÂC - - 330 m ⦠R ON On-state resistance 6 V 1 A 300 õs 25ÃÂC - 170 225 m ⦠150ÃÂC - - 410 m ⦠R G Internal ground resistance I G = 10 mA 95 150 190 ⦠1 For a high side switch, the load pin voltage goes negative with respect to ground during the turn-off of an inductive load. 2 On-state resistance is increased if the supply voltage is less than 9 V. 3 This is the continuous current drawn from the supply when the input is low and includes leakage current to the load. 4 The measured current is in the load pin only. 5 This is the continuous current drawn from the supply with no load connected, but with the input high. 6 Defined as in ISO 10483-1. For comparison purposes only. 7 The supply and input voltage for the R ON tests are continuous. The specified pulse duration t p refers only to the applied load current. July 2001 3 Rev 1.000
Philips Semiconductors Product Specification TOPFET high side switch PIP3209-R INPUT CHARACTERISTICS 9 V ⤠V BG ⤠16 V. Limits are at -40ÃÂC ⤠T mb ⤠150ÃÂC and typicals at T mb = 25 ÃÂC unless otherwise stated. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT I I Input current V IG = 5 V 20 90 160 õA V IG Input clamping voltage I I = 200 õA 5.5 7 8.5 V V IG(ON) Input turn-on threshold voltage - 2.4 3 V V IG(OFF) Input turn-off threshold voltage 1.5 2.1 - V â V IG Input turn-on hysteresis - 0.3 - V I I(ON) Input turn-on current V IG = 3 V - - 100 õA I I(OFF) Input turn-off current V IG = 1.5 V 10 - - õA STATUS CHARACTERISTICS The status output is an open drain transistor, and requires an external pull-up circuit to indicate a logic high. Limits are at -40ÃÂC ⤠T mb ⤠150ÃÂC and typicals at T mb = 25 ÃÂC unless otherwise stated. Refer to TRUTH TABLE. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT V SG Status clamping voltage I S = 100 õA 5.5 7 8.5 V V SG Status low voltage I S = 100 õ A- - 1 V T mb = 25ÃÂC - 0.7 0.8 V I S Status leakage current V SG = 5 V - - 15 õA T mb = 25ÃÂC - 0.1 1 õA I S Status saturation current 1 V SG = 5 V 2 7 12 mA Application information R S External pull-up resistor - 47 - k ⦠OPEN CIRCUIT DETECTION CHARACTERISTICS An open circuit load can be detected in the on-state. Refer to TRUTH TABLE. Limits are at -40ÃÂC ⤠T mb ⤠150ÃÂC and typical is at T mb = 25 ÃÂC. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Open circuit detection 9 V ⤠V BG ⤠35 V I L(TO) Low current detect threshold 50 - 340 mA T j = 25ÃÂC 85 170 255 mA â I L(TO) Hysteresis - 30 - mA 1 In a fault condition with the pull-up resistor short circuited while the status transistor is conducting. This condition should be avoided in order to prevent possible interference with normal operation of the device. July 2001 4 Rev 1.000
Philips Semiconductors Product Specification TOPFET high side switch PIP3209-R UNDERVOLTAGE & OVERVOLTAGE CHARACTERISTICS Limits are at -40ÃÂC ⤠T mb ⤠150ÃÂC and typicals at T mb = 25 ÃÂC. Refer to TRUTH TABLE. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Undervoltage V BG(UV) Low supply threshold voltage 1 2 4.2 5.5 V â V BG(UV) Hysteresis - 0.5 - V Overvoltage V BG(OV) High supply threshold voltage 2 40 45 50 V â V BG(OV) Hysteresis - 1 - V TRUTH TABLE ABNORMAL CONDITIONS DETECTED LOAD INPUT SUPPLY LOAD OUTPUT STATUS DESCRIPTION UV OV LC SC OT L X X X X X OFF H off H 0 0 0 0 0 ON H on & normal H 0 0 1 0 0 ON L on & low current detect H 1 0 X X X OFF H supply undervoltage lockout H 0 1 X 0 0 OFF H supply overvoltage shutdown H 0 0 0 1 X OFF L SC tripped H 0 0 0 0 1 OFF L OT shutdown 3 KEY TO ABBREVIATIONS L logic low UV undervoltage H logic high OV overvoltage X donâÂÂt care LC low current or open circuit load 0 condition not present SC short circuit 1 condition present OT overtemperature 1 Undervoltage sensor causes the device to switch off and reset. 2 Overvoltage sensor causes the device to switch off to protect its load. 3 The status will continue to indicate OT (even if the input goes low) until the device cools below the reset threshold. Refer to OVERLOAD PROTECTION CHARACTERISTICS . July 2001 5 Rev 1.000
Philips Semiconductors Product Specification TOPFET high side switch PIP3209-R OVERLOAD PROTECTION CHARACTERISTICS 5.5 V ⤠V BG ⤠35 V, limits are at -40ÃÂC ⤠T mb ⤠150ÃÂC and typicals at T mb = 25 ÃÂC unless otherwise stated. Refer to TRUTH TABLE. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Overload protection V BL = V BG I L(lim) Load current limiting V BG âÂÂ¥ 9 V 6 9 12 A Short circuit load protection V BL(TO) Battery load threshold voltage 1 V BG = 16 V 8 10 12 V V BG = 35 V 15 20 25 V t d sc Response time 2 V BL > V BL(TO) - 180 250 õs Overtemperature protection T j(TO) Threshold junction 150 170 190 ÃÂC temperature 3 â T j(TO) Hysteresis - 10 - ÃÂC SWITCHING CHARACTERISTICS T mb = 25 ÃÂC, 9 V ⤠V BG ⤠16 V, for resistive load R L = 13 â¦. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT During turn-on to V IG = 5 V t d on Delay time to 10% V L -2 8 4 0 õ s dV/dt on Rate of rise of load voltage 30% to 70% V L - 0.75 1 V/ õs t on Total switching time to 90% V L -6 0 9 0 õ s During turn-off to V IG = 0 V t d off Delay time to 90% V L -3 6 5 4 õ s dV/dt off Rate of fall of load voltage 70% to 30% V L - 0.75 1 V/ õs t off Total switching time to 10% V L -6 0 9 0 õ s CAPACITANCES T mb = 25 ÃÂC; f = 1 MHz; V IG = 0 V. designed in parameters. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT C ig Input capacitance V BG = 13 V - 15 20 pF C bl Output capacitance V BL = 13 V - 100 140 pF C sg Status capacitance V SG = 5 V - 11 15 pF 1 The battery to load threshold voltage for short circuit protection is proportional to the battery supply voltage. After short circuit protection has operated, the input voltage must be toggled low for the switch to resume normal operation. 2 Measured from when the input goes high. 3 After cooling below the reset temperature the switch will resume normal operation. July 2001 6 Rev 1.000
Philips Semiconductors Product Specification TOPFET high side switch PIP3209-R MECHANICAL DATA Fig.4. SOT426 surface mounting package 1 , centre pin connected to mounting base. REFERENCES OUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC EIAJ SOT426 0 2.5 5 mm scale Plastic single-ended surface mounted package (Philips version of D 2 -PAK); 5 leads (one lead cropped) SOT426 e e e e E b A 1 A A 1 L p bc D max. e A UNIT DIMENSIONS (mm are the original dimensions) E 11 mm 4.50 4.10 1.40 1.27 0.85 0.60 0.64 0.46 2.90 2.10 H D 15.80 14.80 Q 2.60 2.20 10.30 9.70 D 1 1.60 1.20 1.70 98-12-14 99-06-25 1 3 24 5 mounting base D 1 H D D Q L p c 1 Epoxy meets UL94 V0 at 1/8". Net mass: 1.5 g. For soldering guidelines and SMD footprint design, please refer to Data Handbook SC18. July 2001 7 Rev 1.000
Philips Semiconductors Product Specification TOPFET high side switch PIP3209-R DEFINITIONS DATA SHEET STATUS DATA SHEET PRODUCT DEFINITIONS STATUS 1 STATUS 2 Objective data Development This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice Preliminary data Qualification This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in ordere to improve the design and supply the best possible product Product data Production This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Changes will be communicated according to the Customer Product/Process Change Notification (CPCN) procedure SNW-SQ-650A Limiting values Limiting values are given in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of this specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. ï Philips Electronics N.V. 2001 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, it is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. 1 Please consult the most recently issued datasheet before initiating or completing a design. 2 The product status of the device(s) described in this datasheet may have changed since this datasheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. July 2001 8 Rev 1.000