Pioneer DEQ-P7050 Installation Manual
Connecting to a sold separately power amp This product can be connected to a sold separately power amp using the RCA output jacks. Connecting the power cord Note: ⢠This unit is for vehicles with a 12-volt battery and negative grounding. Before installing it in a recreational vehicle, truck, or bus, check the bat- tery voltage. ⢠To a void shorts in the electrical system, be sure to disconnect the ÷ battery cable before begin- ning installation. ⢠Refer to the ownerâÂÂs manual for details on con- necting the power amp and other units, then make connections correctly. ⢠Secure the wiring with cable clamps or adhesive tape. T o protect the wiring, wrap adhesive tape around them where they lie against metal parts. ⢠Route and secure all wiring so it cannot touch any moving parts, such as the gear shift, hand- brake and seat rails. Do not route wiring in places that get hot, such as near the heater outlet. If the insulation of the wiring melts or gets torn, there is a danger of the wiring short-circuiting to the vehicle body. ⢠DonâÂÂt pass the yellow lead through a hole into the engine compartment to connect to the battery. This will damage the lead insulation and cause a very dangerous short. ⢠Do not shorten any leads. If you do, the protec- tion circuit may fail to work when it should. ⢠Never feed power to other equipment by cutting the insulation of the power supply lead of the unit and tapping into the lead. The current capac- ity of the lead will be exceeded, causing over- heating. ⢠When replacing fuse, be sure to use only fuse of the rating prescribed on the fuse holder. ⢠Since a unique BPTL circuit is employed, never wire so the speaker leads are directly grounded or the left and right ÷ speaker leads are common. ⢠Speakers connected to this unit must be high- power types with minimum rating of 50 W and impedance of 4 to 8 ohms. Connecting speakers with output and/or impedance values other than those noted here may result in the speakers catch- ing fire, emitting smoke or becoming damaged. ⢠When this productâÂÂs source is switched ON, a control signal is output through the blue/white lead. Connect to an external power ampâ s system remote control or the carâÂÂs Auto-antenna relay control terminal (max. 300 mA 12 V DC). If the car features a glass antenna, connect to the anten- na booster power supply terminal. ⢠When an external power amp is being used with this system, be sure not to connect the blue/white lead to the ampâÂÂs power terminal. Lik ewise, do not connect the blue/white lead to the power ter- minal of the auto-antenna. Such connection could cause excessive current drain and malfunction. ⢠To a void short-circuiting, cover the disconnected lead with insulating tape. Especially, insulate the unused speaker leads without fail. There is a pos- sibility of short-circuiting if the leads are not insulated. ⢠To pre vent incorrect connection, the input side of the IP-BUS or optical cable connector is blue, and the output side is black. Connect the connec- tors of the same colors correctly. ⢠If this unit is installed in a vehicle that does not have an ACC (accessory) position on the ignition switch, the red lead of the unit should be con- nected to a terminal coupled with ignition switch ON/OFF operations. If this is not done, the vehi- cle battery may be drained when you are away from the vehicle for several hours. ⢠The black lead is ground. Please ground this lead separately from the ground of high-current prod- ucts such as power amps. If you ground the products together and the ground becomes detached, there is a risk of dam- age to the products or fire. ⢠To ensure proper heat dissipation of this product, take special care not to block the cooling fan side of this product. No ACC position ACC position O N S T A R T O F F A C C O N S T A R T O F F Connecting the Units <ENGLISH> ⢠Cords for this product and those for other prod- ucts may be different colors even if they ha ve the same function. When connecting this prod- uct to another product, refer to the supplied Installation manuals of both products and con- nect cords that have the same function. INST ALLA TION MANUAL å®Âè£ÂæÂÂå <KMMUF/02B00000> DEQ-P7050 Printed in Japan æÂ¥æΡå· <CRD3605-B> ES This product conforms to new cord colors. 换åÂÂé©åÂÂæ¼æ°åÂÂè»Âç·Âé¡Âè²ã Gray/black White/black Green Violet Left Right White Gray Green/black Violet/black Front speaker Front speaker Rear speaker Rear speaker This product Y ellow To terminal al ways supplied with power regardless of ignition switch position. Fuse holder Black (ground) To v ehicle (metal) body. Blue/white To system control terminal of the po wer amp or Auto-antenna relay control terminal (max. 300 mA 12 V DC). Do not connect anything to the speaker leads that are not connected to speakers. Black Black/white Center speaker â â â â â When you connect a power amp (sold separately), be sure to use the blue/white lead of this unit. If you use the blue/white lead of the head unit, it causes noises. This product Blue/white To system control terminal of the po wer amp or Auto-antenna relay control terminal (max. 300 mA 12 V DC). â â â â â â Front speaker Front speaker Rear speaker Rear speaker Center speaker Subwoofer System remote control RCA cables (sold separately) Power amp (sold separately) Subwoofer output Rear output Front output Center output Power amp (sold separately) Power amp (sold separately) Power amp (sold separately) When you connect a power amp (sold separately), be sure to use the blue/white lead of this unit. If you use the blue/white lead of the head unit, it causes noises.
Routing the optical cable Precaution: ⢠Try not to bend the optical cable sharply . If it is necessary to bend it sharply, make sure that the bending radius is at least 25 mm, otherwise the cable will not transfer signals properly and so this unit will not work properly. ⢠Route the optical cable so that nothing heavy rests on it, and so that it cannot be stepped on or caught in anything â for instance, a door. ⢠Make a loop of diameter at least 200 mm with the remaining optical cable so that the cable does not get strained. ⢠When plugging the optical cable into the unit, use the supplied cable clamps to prevent the cable from being bent sharply. ⢠Route the optical cable so that it does not get caught in moving parts such as the gear shift, hand brake, or seat sliding mechanism. Keep the cable away from hot spots, such as near the heater outlet. Using the corrugated tube To pre vent the optical cable from being strained, use the corrugated tube after cutting it to the cor- rect length. ⢠Insert the optical cable into the cor- rugated tube. Mounting the clamp The clamp is used to secure the optical cable when using it. The other clamp is installed on the back side of the head unit similarly and used to secure the optical cable. 1. Insert the clamp in the direction indicated in the figure, and turn it 90 degrees to lock. 2. Secure the optical cable. Optical cable Clamp Corrugated tube Optical cable Connecting the system Connecting the Units <ENGLISH> Note: ⢠Before finally installing the unit, connect the wiring temporarily, making sure it is all connect- ed up properly, and the unit and the system work properly. ⢠Use only the parts included with the unit to ensure proper installation. The use of unautho- rized parts can cause malfunctions. ⢠Consult with your nearest dealer if installation requires the drilling of holes or other modifica- tions of the vehicle. ⢠Install the unit where it does not get in the dri- verâÂÂs way and cannot injure the passenger if there is a sudden stop, like an emergency stop. ⢠When mounting this unit, make sure none of the leads are trapped between this unit and the sur- rounding metalwork or fittings. ⢠Do not mount this unit near the heater outlet, where it would be affected by heat, or near the doors, where rainwater might splash onto it. ⢠Before drilling any mounting holes always check behind where you want to drill the holes. Do not drill into the gas line, brake line, electrical wiring or other important parts. ⢠If this unit is installed in the passenger compart- ment, anchor it securely so it does not break free while the car is moving, and cause injury or an accident. ⢠If this unit is installed under a front seat, make sure it does not obstruct seat movement. Route all leads and cords carefully around the sliding mechanism so they do not get caught or pinched in the mechanism and cause a short circuit. Installing the unit Mounting with brackets Mounting with velcro tape Thoroughly wipe off the surface before affixing the velcro tape. Car mat or chassis V elcro tape Screw (4 à8 mm) Car mat or chassis Bracket Tapping screw (4 à12 mm) Drill 2 to 2.5 mm diameter holes. Installation <ENGLISH> Rear video output (REAR VIDEO OUTPUT) (Y ellow) RCA cables (sold separately) RCA cable ( supplied) Optical cable (supplied) 20 pin cable (supplied with the display) Y ellow Y ellow Right (Red) Left (White) To audio inputs Right (Red) Left (White) Not used. A V system display (e.g. A VX-7300) (sold separately) 3m Video input (VIDEO INPUT) (Y ellow) FM MODULATOR IP-BUS MAIN UNIT IP-BUS AV MASTER To video input RCA cable (supplied with the head unit) Right (Red) Left (White) Rear audio output (DVD REAR MONITOR OUTPUT) Right (Red) Left (White) This product 3m 3m Front video output (FRONT VIDEO OUTPUT) (Y ellow) Subwoofer output or non fading output (SUBWOOFER OUTPUT or NON-FADING OUTPUT) IP-BUS cable (supplied with the TV tuner) Hide-away TV tuner (e.g. GEX-P7000TVP) (sold separately) Multi-CD player (sold separately) Blue Black Red Green Green Black Blue Blue Display with RCA input jacks Black Blue IP-BUS cable (supplied) Head unit (e.g. DVH-P7050) (sold separately)
Routing the optical cable Precaution: ⢠Try not to bend the optical cable sharply . If it is necessary to bend it sharply, make sure that the bending radius is at least 25 mm, otherwise the cable will not transfer signals properly and so this unit will not work properly. ⢠Route the optical cable so that nothing heavy rests on it, and so that it cannot be stepped on or caught in anything â for instance, a door. ⢠Make a loop of diameter at least 200 mm with the remaining optical cable so that the cable does not get strained. ⢠When plugging the optical cable into the unit, use the supplied cable clamps to prevent the cable from being bent sharply. ⢠Route the optical cable so that it does not get caught in moving parts such as the gear shift, hand brake, or seat sliding mechanism. Keep the cable away from hot spots, such as near the heater outlet. Using the corrugated tube To pre vent the optical cable from being strained, use the corrugated tube after cutting it to the cor- rect length. ⢠Insert the optical cable into the cor- rugated tube. Mounting the clamp The clamp is used to secure the optical cable when using it. The other clamp is installed on the back side of the head unit similarly and used to secure the optical cable. 1. Insert the clamp in the direction indicated in the figure, and turn it 90 degrees to lock. 2. Secure the optical cable. Optical cable Clamp Corrugated tube Optical cable Connecting the system Connecting the Units <ENGLISH> Note: ⢠Before finally installing the unit, connect the wiring temporarily, making sure it is all connect- ed up properly, and the unit and the system work properly. ⢠Use only the parts included with the unit to ensure proper installation. The use of unautho- rized parts can cause malfunctions. ⢠Consult with your nearest dealer if installation requires the drilling of holes or other modifica- tions of the vehicle. ⢠Install the unit where it does not get in the dri- verâÂÂs way and cannot injure the passenger if there is a sudden stop, like an emergency stop. ⢠When mounting this unit, make sure none of the leads are trapped between this unit and the sur- rounding metalwork or fittings. ⢠Do not mount this unit near the heater outlet, where it would be affected by heat, or near the doors, where rainwater might splash onto it. ⢠Before drilling any mounting holes always check behind where you want to drill the holes. Do not drill into the gas line, brake line, electrical wiring or other important parts. ⢠If this unit is installed in the passenger compart- ment, anchor it securely so it does not break free while the car is moving, and cause injury or an accident. ⢠If this unit is installed under a front seat, make sure it does not obstruct seat movement. Route all leads and cords carefully around the sliding mechanism so they do not get caught or pinched in the mechanism and cause a short circuit. Installing the unit Mounting with brackets Mounting with velcro tape Thoroughly wipe off the surface before affixing the velcro tape. Car mat or chassis V elcro tape Screw (4 à8 mm) Car mat or chassis Bracket Tapping screw (4 à12 mm) Drill 2 to 2.5 mm diameter holes. Installation <ENGLISH> Rear video output (REAR VIDEO OUTPUT) (Y ellow) RCA cables (sold separately) RCA cable ( supplied) Optical cable (supplied) 20 pin cable (supplied with the display) Y ellow Y ellow Right (Red) Left (White) To audio inputs Right (Red) Left (White) Not used. A V system display (e.g. A VX-7300) (sold separately) 3m Video input (VIDEO INPUT) (Y ellow) FM MODULATOR IP-BUS MAIN UNIT IP-BUS AV MASTER To video input RCA cable (supplied with the head unit) Right (Red) Left (White) Rear audio output (DVD REAR MONITOR OUTPUT) Right (Red) Left (White) This product 3m 3m Front video output (FRONT VIDEO OUTPUT) (Y ellow) Subwoofer output or non fading output (SUBWOOFER OUTPUT or NON-FADING OUTPUT) IP-BUS cable (supplied with the TV tuner) Hide-away TV tuner (e.g. GEX-P7000TVP) (sold separately) Multi-CD player (sold separately) Blue Black Red Green Green Black Blue Blue Display with RCA input jacks Black Blue IP-BUS cable (supplied) Head unit (e.g. DVH-P7050) (sold separately)