Pioneer DVR-433H-K Operating Instructions

DVD Recorder DVR-433H-S DVR-433H-K Operating Instructions ® DVR-433H_UK.book 1 ページ ２００５年３月１日　火曜日　午後５時６分
D3-4-2-1-1_En-A The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (ser vicing) instructions in the literature accompanying the appliance. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE P ARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN IMPOR T ANT W ARNING This equipment is not waterproof. T o prevent a fir e or shock hazard, do not place any container filed with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain or moisture. D3-4-2-1-3_A_En CAUTION The ST ANDBY/ON switch on this unit will not completely shut off all power from the AC outlet. Since the power cord ser ves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power . Therefore, make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. T o avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation). D3-4-2-2-2a_A_En W ARNING The voltage of the available power supply differs according to country or r egion. Be sure that the power supply voltage of the area wher e this unit will be used meets the requir ed voltage (e.g., 230V or 120V) written on the rear panel. D3-4-2-1-4_A_En Before plugging in for the first time, read the following section carefully . This product complies with the Low V oltage Directive (73/23/EEC, amended by 93/68/EEC), EMC Directives (89/336/EEC, amended by 92/31/EEC and 93/68/EEC). D3-4-2-1-9a_En Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly . After you have finished reading the instructions, put them away in a safe place for future reference. CAUTION This product is a class 1 laser product, but this product contains a laser diode higher than Class 1. To ensure continued safety , do not remove any covers or attempt to gain access to the inside of the product. Refer all servicing to qualified personnel. D3-4-2-1-8_A_En CAUTION A TTENTION CLASS 3B VISIBLE AND INVISIBLE LASER RADIA TION WHEN OPEN, AVOID EXPOSURE TO THE BEAM. DRW2247 - A RADIA TIONS LASER VISIBLES ET INVISIBLES DE CLASSE 3B QUAND OUVERT . ÉVITEZ TOUT EXPOSITION AU FAISCEAU. ADV ARSEL KLASSE 3B SYNLIG OG USYNLIG LASERSTRÅLING VED ÅBNING. UNDGÅ UDSÆTTELSE FOR STRÅLING. V ARNING KLASS 3B SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD. UNDVIK A TT UTSÄTT A DIG FÖR STRÅLEN. V ARO! AV AT T AESSA OLET AL TTIINA NÄKYVÄLLE JA NÄKYMÄTTÖMÄLLE LUOKAN 3B LASERSÄTEIL YLLE. ÄLÄ KA TSO SÄTEESEEN. PRECAUCIAÓN CUANDO SE ABRE HA Y RADIACIÓN LÁSER DE CLASE 3B VISIBLE E INVISIBLE. EVITE LA EXPOSICIÓN A LOS RA YOS LÁSER. VORSICHT BEI GEÖFFNETER ABDECKUNG IST SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG DER KLASSE 3B IM GERÄTEINNEREN VORHANDEN. AUGEN NICHT DEM LASERSTRAHLAUSSETZEN! The following caution label appears on your unit. Location: inside of the unit DVR-433H_UK.book 2 ページ ２００５年３月１日　火曜日　午後５時６分
W ARNING To prevent a fire hazar d, do not place any naked flame sources (such as a lighted candle) on the equipment. D3-4-2-1-7a_A_En VENTILA TION CAUTION When installing this unit, make sure to leave space around the unit for ventilation to impr ove heat radiation (at least 10 cm at top, 10 cm at rear , and 10 cm at each side). W ARNING Slots and openings in the cabinet are pr ovided for ventilation to ensure r eliable operation of the product, and to pr otect it from overheating. T o prevent fir e hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the equipment on thick carpet or a bed. D3-4-2-1-7b_A_En Operating Environment Operating environment temperature and humidity : 5 ºC – 35 ºC ( 41 ºF – 95 ºF); less than 85 %RH (cooling vents not blocked) Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light) D3-4-2-1-7c_A_En This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. This product is for general household purposes. Any failure due to use for other than household purposes (such as long- term use for business purposes in a restaurant or use in a car or ship) and which requires repair will be charged for even during the warranty period. K041_En This product includes F ontAvenue ® fonts licenced b y NEC corpor ation. F ontAv enue is a r egist ered tr ademark of NEC Corpor ation. POWER-CORD CAUTION Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause a fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest PIONEER authorized ser vice center or your dealer for a replacement. S002_En If the AC plug of this unit does not match the AC outlet you want to use, the plug must be removed and appropriate one fitted. Replacement and mounting of an AC plug on the power supply cord of this unit should be per formed only by qualified ser vice personnel. If connected to an AC outlet, the cut-off plug can cause severe electrical shock. Make sure it is properly disposed of after removal. The equipment should be disconnected by removing the mains plug from the wall socket when not left unused for a long period of time (for example, when on vacation). D3-4-2-2-1a_A_En Do not connect either wire to the earth terminal of a three pin plug. NOTE After replacing or changing a fuse, the fuse cover in the plug must be replaced with a fuse cover which corresponds to the colour of the insert in the base of the plug or the word that is embossed on the base of the plug, and the appliance must not be used without a fuse cover . If lost replacement fuse covers can be obtained from your dealer . Only 5 A fuses approved by B.S.I or A.S.T .A to B.S.1362 should be used. D3-4-2-1-2-2_En The wires in this mains lead are colour ed in accordance with the following code: Blue : Neutral Br own : Live If the plug provided is unsuitable for your socket outlets, the plug must be cut off and a suitable plug fitted. IMPOR T ANT FOR USE IN THE UNITED KINGDOM The cut-off plug should be disposed of and must not be inserted into any 13 amp socket as this can result in electric shock. The plug or adaptor or the distribution panel should be provided with 5 A fuse. As the colours of the wires in the mains lead of this appliance may not correspond with coloured markings identifying the terminals in your plug, proceed as follows ; The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified ser vice personnel. DVR-433H_UK.book 3 ページ ２００５年３月１日　火曜日　午後５時６分
4 En Contents 01 Before you start Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 What’s in the box . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Putting the batteries in the remote control . . . . . . . . . 8 Using the remote control . . . . . . . . . . . . . . . . . . . . . . 8 Disc / content format playback compatibility . . . . . . . 9 About the internal hard disk drive . . . . . . . . . . . . . . . 11 02 Connecting up Rear panel connections . . . . . . . . . . . . . . . . . . . . . . 12 Front panel connections . . . . . . . . . . . . . . . . . . . . . . 12 Extra features for use with compatible TVs . . . . . . . . 13 Easy connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Using other types of audio/video output . . . . . . . . . . 15 Connecting to a cable box, satellite receiver or digital terrestrial receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Connecting an external decoder box (1) . . . . . . . . . . 17 Connecting an external decoder box (2) . . . . . . . . . . 18 Connecting to an AV amplifier/receiver . . . . . . . . . . 19 Connecting other AV sources . . . . . . . . . . . . . . . . . . 20 Plugging in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 03 Controls and displays Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 04 Getting started Switching on and setting up . . . . . . . . . . . . . . . . . . . 25 Selecting the hard disk or DVD for playback and recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Making your first recording . . . . . . . . . . . . . . . . . . . . 28 Using the built-in TV tuner . . . . . . . . . . . . . . . . . . . . 29 Basic playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Using the Home Menu . . . . . . . . . . . . . . . . . . . . . . . 34 Displaying disc information on-screen . . . . . . . . . . . 34 05 Recording About DVD recording . . . . . . . . . . . . . . . . . . . . . . . . 37 About HDD recording . . . . . . . . . . . . . . . . . . . . . . . . 37 Recording time and picture quality . . . . . . . . . . . . . . 38 Recorded audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Restrictions on video recording . . . . . . . . . . . . . . . . 38 Setting the picture quality/recording time . . . . . . . . 39 Basic recording from the TV . . . . . . . . . . . . . . . . . . . 39 Setting a timer recording . . . . . . . . . . . . . . . . . . . . . 41 Timer recording FAQ . . . . . . . . . . . . . . . . . . . . . . . . 47 Simultaneous recording and playback . . . . . . . . . . . 48 Recording from an external component . . . . . . . . . . 48 Automatic recording from a satellite tuner . . . . . . . . 49 Recording from a DV camcorder . . . . . . . . . . . . . . . 50 Playing your recordings on other DVD players . . . . . 51 Initializing a recordable DVD disc . . . . . . . . . . . . . . . 52 06 Playback Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Navigating discs and the HDD . . . . . . . . . . . . . . . . . 53 Using the Disc Navigator to browse the contents of a disc. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Scanning discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Playing in slow motion . . . . . . . . . . . . . . . . . . . . . . . 56 Frame advance/frame reverse . . . . . . . . . . . . . . . . . 57 The Play Mode menu . . . . . . . . . . . . . . . . . . . . . . . . 57 Displaying and switching subtitles . . . . . . . . . . . . . . 60 Switching DVD soundtracks . . . . . . . . . . . . . . . . . . . 61 Switching audio channels . . . . . . . . . . . . . . . . . . . . 61 Switching camera angles . . . . . . . . . . . . . . . . . . . . . 62 07 Copying and back-up Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 One Touch Copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Using Copy Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Using disc back-up . . . . . . . . . . . . . . . . . . . . . . . . . . 71 08 Editing The Disc Navigator screen . . . . . . . . . . . . . . . . . . . . 73 Command menu panel options . . . . . . . . . . . . . . . . 74 Editing accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 HDD genres . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 09 Using the Jukebox Copying CDs to the HDD . . . . . . . . . . . . . . . . . . . . . 82 Playing music from the Jukebox . . . . . . . . . . . . . . . . 83 Editing Jukebox albums . . . . . . . . . . . . . . . . . . . . . . 83 10 The PhotoViewer Playing a slideshow . . . . . . . . . . . . . . . . . . . . . . . . . 85 DVR-433H_UK.book 4 ページ ２００５年３月１日　火曜日　午後５時６分
5 En 11 The Disc Setup menu Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 Basic settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 Initialize settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 Finalize settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 Optimize HDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 Initialize HDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 12 The Video/Audio Adjust menu Setting the picture quality for TV and external inputs 89 Setting the picture quality for disc playback . . . . . . 90 Audio DRC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 13 The Initial Setup menu Using the Initial Setup menu . . . . . . . . . . . . . . . . . . 92 14 Additional information Screen sizes and disc formats . . . . . . . . . . . . . . . . 101 Minimum copying times . . . . . . . . . . . . . . . . . . . . 102 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 Frequently asked questions . . . . . . . . . . . . . . . . . . 105 About DV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 Manual recording modes . . . . . . . . . . . . . . . . . . . . 107 Language code list . . . . . . . . . . . . . . . . . . . . . . . . . 108 Country/Area code list . . . . . . . . . . . . . . . . . . . . . . 108 On-screen displays and recorder displays . . . . . . . 109 Resetting the recorder . . . . . . . . . . . . . . . . . . . . . . 111 Handling discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 Cleaning the pickup lens . . . . . . . . . . . . . . . . . . . . 111 Condensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 Hints on installation . . . . . . . . . . . . . . . . . . . . . . . . 112 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 Index DVR-433H_UK.book 5 ページ ２００５年３月１日　火曜日　午後５時６分
Before you start 01 6 En Chapter 1 Before you start Features • HDD recording Record up to 227 hours of video (in MN1 mode) on the internal 80 GB (gigabyte) hard disk (HDD). With both recordable DVD and a high-capacity HDD in the same recorder, you have the flexibility to keep recordings on the HDD for quick access anytime, or record to DVD for archiving or playing on other DVD players. • Copy between HDD and DVD You can quickly and easily copy recordings between the HDD and DVD. When copying to DVD you can usually use the high-speed copy feature, which can copy an hour of video in about one minute (when recorded in SEP mode using a DVD-R Ver. 2.0 / 2.1 (16x) disc). You can also choose to copy material at a different recording quality from the original. For example, you might want to copy an XP mode (highest quality) recording on the HDD to SP (standard play) quality on a DVD so that you can fit other recordings on the same disc. • One Touch Copy One Touch Copy makes copying the currently playing title from HDD to DVD, or DVD to HDD as simple as pressing a button. • High quality, real-time copying When recording to the HDD, picture quality data is also stored so that picture quality can be optimized when making real-time copies to DVD later. (This is applicable only to MN16–32 HDD recordings (Video Mode Off), or MN12–32 / XP recordings (Video Mode On). • Chase play Using chase play you can start watching a recording from the beginning, while continuing to record. For example, you could set a timer recording for a program that you’re going to miss the first 15 minutes of, then start watching while the recorder is still recording the program 15 minutes ahead of you. • Simultaneous recording and playback HDD and DVD playback and recording are completely independent. For example, you can record a broadcast program to a recordable DVD, while watching another recording you already made on the same DVD. • On-screen Help Use the HELP button on the remote control to display a help screen for the current operation. • Disc Navigator The on-screen Disc Navigator makes finding your way around the contents of a disc or the HDD easy. For recordable DVD and HDD content, moving thumbnail images are displayed for ease of use. The Disc Navigator is also where you can edit HDD and recordable DVD content. • Home Menu The Home Menu gives you on-screen access to all the recorder’s features in one convenient place, from setting up the recorder, to programming a timer recording and editing a recording. • Progressive scan-compatible Compared to standard interlaced video, progressive scan effectively doubles the amount of video information fed to your TV or monitor. The result is a stable, flicker-free image. (Check your TV/monitor for compatibility with this feature.) • Cinema-style surround sound in your home Connect this recorder to a Dolby Digital and/or DTS- compatible AV amp/receiver to enjoy full surround sound effects from Dolby Digital and DTS DVD discs. • Easy Timer Recording Setting the recorder to record a program is simple from the Easy Timer Recording screen. Set the channel to record and the recording quality, then graphically set the start and end times of the recording. That’s it! • Program up to 32 timer recordings You can program the recorder to record up to 32 programs, up to a month in advance. As well as single programs, you can specify daily or weekly recordings, too. * is a registered trademark of Gemstar Development Corporation. The VIDEO Plus system is manufactured under license from Gemstar Development Corporation. • One Touch Recording Use One Touch Recording to start recording immediately in 30 minute blocks. Each time you press the  REC button, the recording time is extended by another 30 minutes, up to six hours. HDD VR mode HDD VR mode HDD ® DVR-433H_UK.book 6 ページ ２００５年３月１日　火曜日　午後５時６分
Before you start 01 7 En • Optimized recording Optimized recording adjusts the recording quality automatically if a timer recording will not fit onto a disc with the settings that you made. • Auto Start Recording from satellite receiver or other set top box With a satellite receiver or other set top box connected to the AV2/AUTO START REC inputs of this recorder, you can start and stop recording automatically according to the timer settings of the set top box. • Super high quality HDD recording Using the XP recording mode you can record super high quality video (around 15 Mbps data transfer rate) to the HDD. • High quality 16-bit Linear PCM audio In the LPCM recording mode, audio is recorded in uncompressed 16-bit Linear PCM format. This delivers great sounding audio to accompany the high picture quality. • Picture quality adjustment features During playback, you can adjust various picture quality settings to improve the picture. You can also adjust the recording picture quality. For example, if you want to make a DVD copy of an old video tape, you can optimize the picture quality before transferring it to disc. • Find what you want to watch quickly and easily Unlike video tape that needs to be wound to the correct place, you can jump right to the part of a DVD disc or the HDD that you want to watch. Search for a point on a disc by title, chapter or time. • Manual recording In addition to six preset recording quality modes, the manual recording mode allows you to access 34 different recording quality/time settings, giving you precise control over the recording. • Record from a DV camcorder This recorder has a built-in DV (Digital Video) input for connection to a DV camcorder. This makes it ideal for transferring camcorder footage to DVD or HDD for editing. • Safe, non-destructive editing When editing Play List content, the actual content of the disc (the Original content) is not touched. The edited version (the Play List content) just points to various parts of the Original content. • Play Video mode recordings on a regular DVD player Discs recorded using the Video mode can be played back on regular DVD players, including computer DVD drives compatible with DVD-Video playback * . * ‘DVD-Video format’ recording: The use of the DVD-Video format for recording on DVD-R and DVD-RW discs is referred to as recording in ‘Video mode’ on Pioneer’s DVD recorders. Supporting playback of DVD- R / DVD-RW discs is optional for manufacturers of DVD playback equipment, and there is DVD playback equipment that does not play DVD-R or DVD-RW discs recorded in the DVD-Video format. Note: ‘Finalization’ is required. • WMA, MP3 and JPEG file playback This recorder can play WMA and MP3 audio files and JPEG picture files on CD-R, CD-RW or CD-ROM discs. • Disc Back-up The disc back-up feature gives you a convenient way to back-up important material on a finalized Video mode DVD to another recordable DVD disc. The material is first copied to the HDD, then on to a second DVD disc. • Recovery Recording When a timer recording is set to use DVD but the disc loaded at the time of the recording is unrecordable, the program will automatically be recorded to the HDD. • Auto Replace Recording This feature is useful for regular timer recordings of a TV program which you don’t want to keep after watching. Each time the program is recorded, it replaces the one currently on the HDD. There’s no need to manually delete it later. HDD VR mode Note on copying: Recording equipment should be used only for lawful copying and you are advised to check carefully what is lawful copying in the country in which you are making a copy. Copying of copyright material such as films or music is unlawful unless permitted by a legal exception or consented to by the rightowners. Video mode HDD HDD DVR-433H_UK.book 7 ページ ２００５年３月１日　火曜日　午後５時６分
Before you start 01 8 En What’s in the box Please confirm that the following accessories are in the box when you open it. • Remote control • AA/R6P dry cell batteries x2 • Audio/video cable (red/white/yellow) • RF antenna cable • Power cable • These operating instructions • Warranty card Putting the batteries in the remote control 1 Open the battery compartment cover on the back of the remote control. 2 Insert two AA/R6P batteries into the battery compartment following the indications (  ,  ) inside the compartment. 3 Close the cover. Important Incorrect use of batteries can result in hazards such as leakage and bursting. Please observe the following: • Don’t mix new and old batteries together. • Don’t use different kinds of batteries together— although they may look similar, different batteries may have different voltages. • Make sure that the plus and minus ends of each battery match the indications in the battery compartment. • Remove batteries from equipment that isn’t going to be used for a month or more. • When disposing of used batteries, please comply with governmental regulations or environmental public instruction’s rules that apply in your country or area. Using the remote control Please keep in mind the following when using the remote control: • Make sure that there are no obstacles between the remote and the remote sensor on the unit. • Remote operation may become unreliable if strong sunlight or fluorescent light is shining on the unit’s remote sensor. • Remote controllers for different devices can interfere with each other. Avoid using remotes for other equipment located close to this unit. • Replace the batteries when you notice a fall off in the operating range of the remote. • When the batteries run down or you change the batteries, the remote control mode and TV preset codes are automatically reset. See Remote Control Mode on page 98 to reset them. • Use within the operating range in front of the remote control sensor on the front panel, as shown. • You can control this recorder using the remote sensor of another Pioneer component using the CONTROL IN jack on the rear panel. See Rear panel connections on page 12 for more information. 7 m DVR-433H_UK.book 8 ページ ２００５年３月１日　火曜日　午後５時６分
Before you start 01 9 En Disc / content format playback compatibility General disc compatibility This recorder is compatible with a wide range of disc types (media) and formats. Playable discs will generally feature one of the following logos on the disc and/or disc packaging. Note however that some disc types, such as recordable CD and DVD, may be in an unplayable format—see below for further compatibility information. • Also compatible with KODAK Picture CD • is a trademark of DVD Format/Logo Licensing Corporation. • is a trademark of Fuji Photo Film Co. Ltd. This recorder also supports the IEC’s Super VCD standard. Compared to the Video CD standard, Super VCD offers superior picture quality, and allows two soundtracks to be recorded. Super VCD also supports the widescreen size. DVD-R/RW compatibility This recorder will play and record DVD-R/RW discs. Compatible media: • DVD-RW Ver. 1.1, Ver. 1.1 / 2x, Ver. 1.2 / 2–4x and Ver. 1.2 / 2–6x • DVD-R Ver. 2.0 and Ver. 2.0 / 4x / 8x/ 16x, and Ver. 2.1 1–8x / 1–16x Recording formats: • DVD-R/RW: Video Recording (VR) format and DVD- Video format (Video mode) Readable formats: • DVD-R/RW: Video Recording (VR) format and DVD- Video format (Video mode) Note that older models of DVD recorders and DVD writers may reject DVD-RW Ver. 1.2 discs and/or corrupt the data on the disc. If you want to share DVD-RW discs between this recorder and an older recorder/writer, we recommend using Ver. 1.1 discs. The following table shows older Pioneer DVD recorders’ limited compatibility with DVD-RW Ver. 1.2 discs. 1 Discs should be finalized in this recorder before playing. Unfinalized VR mode and Video mode discs may not play. 2 Cannot read the CPRM information will show in the display when you load a disc. However, this will not affect playback. 3 Copy-once protected disc titles will not play. CD-R/RW compatibility This recorder cannot record CD-R or CD-RW discs. • Readable formats: CD-Audio, Video CD /Super VCD, ISO 9660 CD-ROM* containing MP3, WMA or JPEG files * ISO 9660 Level 1 or 2 compliant. CD physical format: Mode1, Mode2 XA Form1. Romeo and Joliet file systems are both compatible with this recorder. • Multi-session playback: Yes (except CD-Audio and Video CD/Super VCD) • Unfinalized disc playback: CD-Audio only Compressed audio compatibility • Compatible media: CD-ROM, CD-R, CD-RW • Compatible formats: MPEG-1 Audio Layer 3 (MP3), Windows Media Audio (WMA) • Sampling rates: 44.1 or 48kHz • Bit-rates: Any (128Kbps or higher recommended) • Variable bit-rate (VBR) MP3 playback: Yes • VBR WMA playback: No • WMA encoder compatibility: Windows Media Codec 8 (files encoded using Windows Media Codec 9 may be playable but some parts of the specification are not supported; specifically, Pro, Lossless, Voice and VBR) • DRM (Digital Rights Management) file playback: No (see also DRM in the Glossary on page 113) • File extensions: .mp3, .wma (these must be used for the recorder to recognize MP3 and WMA files – do not use for other file types) • File structure: Up to 99 folders / 999 files (if these limits are exceeded, only files and folders up to these limits are playable) DVD-Video DVD-R DVD-RW Video CD Audio CD CD-R CD-RW VIDEO CD Su per Video CD (Super VCD) Model Playable Recordable DVR-7000 Yes 1,2,3 No DVR-3100/ DVR-5100H Yes 1 No DVR-433H_UK.book 9 ページ ２００５年３月１日　火曜日　午後５時６分
Before you start 01 10 En WMA (Windows Media Audio) compatibility The Windows Media ® logo printed on the box indicates that this recorder can playback Windows Media Audio content. WMA is an acronym for Windows Media Audio and refers to an audio compression technology developed by Microsoft Corporation. WMA content can be encoded by using Windows Media ® Player for Windows ® XP, Windows Media ® Player 9 or Windows Media ® Player 10 series. Microsoft, Windows Media, and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States and/or other countries. JPEG file compatibility • Compatible formats: Baseline JPEG and EXIF 2.2* still image files * File format used by digital still cameras • Sampling ratio: 4:4:4, 4:2:2, 4:2:0 • Horizontal resolution: 160 – 5120 pixels • Vertical resolution: 120 – 3840 pixels • Progressive JPEG compatible: No • File extensions: .jpg, .jpeg, .jif, .jfif (must be used for the recorder to recognize JPEG files – do not use for other file types) • File structure: The recorder can load up to 99 folders / 999 files at one time (if there are more files/folders that this on the disc then more can be reloaded) PC-created disc compatibility Discs recorded using a personal computer may not be playable in this unit due to the setting of the application software used to create the disc. In these particular instances, check with the software publisher for more detailed information. Discs recorded in packet write mode (UDF format) are not compatible with this recorder. Check the DVD-R/RW or CD-R/RW software disc boxes for additional compatibility information. Frequently asked questions • What’s the difference between DVD-R and DVD-RW? The most important difference between DVD-R and DVD-RW is that DVD-R is a record-once medium, while DVD-RW is a re-recordable/erasable medium. You can re-record/erase a DVD-RW disc approximately 1,000 times. For more information, see About DVD recording on page 37. • What’s VR mode? VR (Video Recording) mode is a special mode designed for home DVD recording. It allows flexible editing of recorded material compared to ‘Video mode’. On the other hand, Video mode discs are more compatible with other DVD players. • How do I change the format of a disc? Both DVD-R and DVD-RW discs can be initialized for Video mode or VR mode recording. DVD-R discs are ready for Video mode recording when you first load them into the recorder. You can, however, initialize them for VR mode recording from the Disc Setup menu. DVD-RW discs can be initialized and re-initialized for either mode at any time (although initializing will erase all the data on the disc). • Can I play my recordable discs in a regular DVD player? Generally, DVD-R discs and DVD-RW discs recorded in Video mode* are playable in a standard DVD player, but they must be ‘finalized’ first. This process fixes the contents of the disc to make them readable to other DVD players as DVD-Video discs. DVD-R discs recorded in VR mode are not playable in standard DVD players, but may be playable in other DVD recorders and DVD-ROM drives (in the case of DVD-ROM drives, the disc will need to be finalized first). DVD-RW discs recorded in VR mode are playable in some players and other recorders. Note that discs may not play due to recording or disc characteristics, scratches or dirt on the disc or pickup lens, etc. This label indicates playback compatibility with DVD-RW discs recorded in VR mode (Video Recording format). However, for discs recorded with a record-only-once encrypted program, playback can only be achieved using a CPRM compatible device. Note that Pioneer cannot guarantee that discs recorded using this recorder will play on other players. DVR-433H_UK.book 10 ページ ２００５年３月１日　火曜日　午後５時６分
Before you start 01 11 En * ‘DVD-Video format’ recording: The use of the DVD- Video format for recording on DVD-R and DVD-RW discs is referred to as recording in ‘Video mode’ on Pioneer’s DVD recorders. Supporting playback of DVD-R / DVD- RW discs is optional for manufacturers of DVD playback equipment, and there is DVD playback equipment that does not play DVD-R or DVD-RW discs recorded in the DVD-Video format. Note: ‘Finalization’ is required. This recorder supports the recording of ‘copy-once’ broadcast programs using the CPRM copy protection system (see CPRM on page 38) on CPRM-compliant discs in VR mode. CPRM recordings can only be played on players that are specifically compatible with CPRM. • Do I need two DVD recorders for editing? What kind of editing can I do? Unlike editing video tape, you only need one DVD recorder to edit discs. With VR mode discs, you can edit by making a ‘Play List’ of what to play and when to play it. On playback, the recorder plays the disc according to the Play List. Throughout this manual, you will often see the words Original and Play List to refer to the actual content and the edited version. • Original content refers to what’s actually recorded on the disc. • Play List content refers to the edited version of the disc—how the Original content is to be played. About the internal hard disk drive The internal hard disk drive (HDD) is a fragile piece of equipment. Depending on the conditions under which it is used, or through careless use, it is possible that the recorded contents will be damaged or lost completely, or that normal playback and recording will not be possible. Please understand that in the event of repair or replacement of the HDD or related components, all your HDD recordings will be lost. Please use the recorder following the guidelines below to protect against possible HDD failure. The HDD should not be regarded as a place to store recordings permanently. We recommend that you back up your important recordings onto DVD-R/RW discs in order to protect against accidental loss. Pioneer cannot under any circumstances accept resposibility for any direct or indirect loss arising from any inconvenience or loss of recorded material resulting from HDD failure. • Install and use the recorder on a stable, level surface. • Do not block the rear vent/cooling fan. • Do not use the recorder in excessively hot or humid places, or in places that may be subject to sudden changes in temperature. Sudden changes in temperature can cause condensation to form inside the recorder. This can be a cause of HDD failure. • Do not move the recorder immediately after switching it off. If you need to move the recorder, please follow the steps below: 1 After the message POWER OFF is shown in the display, wait at least two minutes. 2 Unplug from the wall socket. 3 Move the recorder. • If there’s a power failure while the recorder is on there is a chance that some data on the HDD will be lost. • The HDD is very delicate. If used improperly or in an unsuitable environment, it is possible that the HDD will fail after a few years of use. Signs of problems include playback unexpectedly freezing and noticeable block noise (mosaic) in the picture. However, sometimes there will be no warning signs of HDD failure. If the HDD fails, no playback of recorded material will be possible. In this case it will be necessary to replace the HDD unit. Optimizing HDD performance As you record and edit material on the HDD, the data on the disk becomes fragmented, eventually affecting the recorder’s performance. Before this happens, the recorder will warn you that it is time to optimize the HDD (which you can do from the Disc Setup menu; see Optimize HDD on page 88). Original Title 1 Play List Title 2 Title 1 Title 3 Title 2 Chapt er 1 C hapter 1 Chapter 2 Chapter 3 Chapter 2 Chapt er 2 Chapter 1 Chapter 2 Chapter 1 Chapter 1 DVR-433H_UK.book 11 ページ ２００５年３月１日　火曜日　午後５時６分
Connecting up 02 12 En Chapter 2 Connecting up Rear panel connections 1 AV2/AUTO START REC(INPUT 1/DECODER) AV connector Audio/video input/output SCART-type AV connector for connecting to a VCR, or other equipment with a SCART connector. The input accepts video, S-video and RGB. See AV2/L1 In on page 94 for how to set this up. 2 AV1(RGB)-TV AV connector Audio/video output SCART-type AV connector for connecting to a TV or other equipment with a SCART connector. The video output is switchable between video, S-video and RGB. See page AV1 Out on page 94 for how to set this up. 3 COMPONENT VIDEO OUT A high-quality video output for connecting to a TV or monitor with a component video input. 4 ANTENNA IN (RF IN)/OUT Connect your TV antenna to the ANTENNA IN (RF IN) jack. The signal is passed through to the ANTENNA OUT jack for connection to your TV. 5 AC IN – Power inlet 6 CONTROL IN Use to control this recorder from the remote sensor of another Pioneer component with a CONTROL OUT terminal and bearing the Pioneer  mark. Connect the CONTROL OUT of the other component to the CONTROL IN of this recorder using a mini-plug cord. 7 DIGITAL AUDIO OUT Optical digital audio jack for connecting to an AV amplifier/receiver, Dolby Digital/DTS/MPEG decoder or other equipment with a digital input. 8 INPUT 3 Stereo analog audio, video and S-video inputs for connection to a VCR or other source component. 9 OUTPUT Stereo analog audio, video and S-video outputs for connection to a TV or AV amplifier/receiver. Front panel connections On the right side of the front panel a flip-down cover hides more connections. 10 DV IN A DV input i.LINK connector, suitable for connecting a DV camcorder. 11 Audio/video input 2 Audio/video input (stereo analog audio; composite and S-video video), especially suitable for camcorders, game consoles, portable audio, etc. DIGITAL OUT CONT ROL IN OPTICAL AV 1 (RGB) – TV AV 2/ AUTO START REC (INPUT 1/DECODER) S-VIDEO VIDEO AU DIO L R COMPO N ENT VIDEO OUT Y P B P R ANTENNA IN OUT AC IN OUTPUT S-VIDEO VIDEO AUDIO L R INPUT 3 1 5 6 7 8 9 2 3 4 V I D E O L ( M O N O ) A UD I O I N P U T 2 R S - V I D E O D V I N 10 11 DVR-433H_UK.book 12 ページ ２００５年３月１日　火曜日　午後５時６分
Connecting up 02 13 En Extra features for use with compatible TVs When this recorder is connected to a TV that features i/o Link. A, AV Link, T-V Link, EasyLink, MegaLogic, SMARTLINK, Q-Link, DATA LOGIC or NexTView Link using a fully-wired 21-pin SCART cable (not supplied), the following functions are available: • Direct TV recording • Channel preset download • NexTView timer programming download • TV auto power on • System configuration For further details and compatibility information, see also the manual that came with your TV. Direct TV recording Direct TV recording allows you to record the TV program that you’re watching, without having to worry about whether this recorder is set to the same channel. See Direct recording from TV on page 40 for more on this feature. Channel preset download This feature allows you to set up the channel presets of this recorder very simply using the channel presets and preset names already in your TV. See Switching on and setting up on page 25 and Auto Channel Setting on page 93 for more on this feature. NexTView timer programming download NexTView timer programming download allows you to program a timer recording directly from the NexTView electronic program guide displayed on your TV. See the manual that came with your TV for more information on how to use this feature. Note that the SP and LP options displayed on your TV correspond to the SP and LP recording modes on this recorder. TV auto power on When you play a disc in this recorder, the TV automatically turns on and switches to the correct video input. See the manual that came with your TV for how to use this feature. System configuration Basic settings, including language, country and TV screen size (aspect ratio), can be downloaded from your TV to help set up this recorder for use. DVR-433H_UK.book 13 ページ ２００５年３月１日　火曜日　午後５時６分
Connecting up 02 14 En Easy connections The setup described below is a basic setup that allows you to watch and record TV programs, and play discs. Other types of connections are explained starting on the following page. Important • These connections use SCART cables (not supplied). If your TV (or VCR) does not have a SCART connection, see the following page for connecting up using the supplied audio/video cable. • The AV1(RGB)-TV AV connector can output ordinary (composite), S-video or RGB video, plus stereo analog audio. The AV2/AUTO START REC(INPUT 1/DECODER) connector accepts ordinary, S-video and RGB video input, as well as stereo analog audio. See AV1 Out on page 94 and AV2/L1 In on page 94 for how to set them up. • Before making or changing any rear panel connections, make sure that all components are switched off and unplugged from the wall outlet. 1 Connect the cable from the antenna/cable TV outlet to the antenna input on your VCR. • If you are not connecting a VCR in the chain, connect it to the ANTENNA IN (RF IN) jack on this recorder and skip the next step. 2 Use an RF antenna cable (one is supplied) to connect the antenna output of your VCR to the ANTENNA IN (RF IN) of this recorder. 3 Use another RF antenna cable to connect the ANTENNA OUT of this recorder to the antenna input on your TV. 4 Use a SCART cable (not supplied) to connect the AV1(RGB)-TV AV connector on this recorder to the SCART AV connector on your TV. 5 Use another SCART cable to connect the AV2/ AUTO START REC(INPUT 1/DECODER) AV connector to a SCART AV connector on your VCR. Tip • This recorder has a ‘through’ function which allows you to record a TV program from the built-in TV tuner in this recorder while watching a video playing on your VCR. (To use this feature when the recorder is in standby, Power Save must be set to Off —see Power Save on page 92). TV VCR DIGITAL OUT CONT ROL IN OPTICAL AV 1 (RGB) – TV AV 2/AUTO START REC (INPUT 1/DECODER) S-VIDEO VIDEO AU DIO L R COMPON ENT VIDEO OUT Y P B P R IN OUT AC IN OUTPUT S-VIDEO VIDEO AU DIO L R INPUT 3 ANTENNA Antenna/cable TV wall outlet SCART AV CONNECTOR SCART AV CONNECTOR ANTENNA IN ANTENNA IN (RF IN) ANTENNA OUT ANTENNA OUT ANTENNA IN 1 2 4 5 3 DVR-433H_UK.book 14 ページ ２００５年３月１日　火曜日　午後５時６分
Connecting up 02 15 En Using other types of audio/video output If you can’t use the SCART AV connector to connect your TV to this recorder, there are standard audio/video output jacks, as well as an S-video and component video output. Using the supplied audio/video cable 1 Connect the VIDEO OUTPUT jack to a video input on your TV. Use the yellow jack of the supplied audio/video cable for the video connection. 2 Connect the AUDIO OUTPUT jacks to the corresponding audio inputs on your TV. Use the red and white jacks of the supplied audio/video cable for the audio connection. Make sure you match up the left and right outputs with their corresponding inputs for correct stereo sound. Using the S-video or component video output 1 Connect the S-video or component video output to a similar input on your TV. For an S-video connection, use an S-video cable (not supplied) to connect the S-VIDEO OUTPUT jack to an S- video input on your TV For a component video connection, use a component video cable (not supplied) to connect the COMPONENT VIDEO OUT jacks to a component video input on your TV. See also Component Video Out on page 94 for how to set up the component video output for use with a progressive scan-compatible TV. 2 Connect the AUDIO OUTPUT jacks to the corresponding audio inputs on your TV. You can use the supplied audio/video cable, leaving the yellow video plug disconnected. Make sure you match up the left and right outputs with their corresponding inputs for correct stereo sound. TV DIGITAL OUT CONT ROL IN OPTICAL AV 1 (RGB) – TV AV 2/AUTO START REC (INPUT 1/DECODER) S-VIDEO VIDEO AU DIO L R CO MPONENT VIDEO OUT Y P B P R IN OUT AC IN OUTPUT S-VIDEO VIDEO AUDIO L R INPUT 3 ANTENNA VIDEO INPUT AUDIO INPUT 1 2 TV DIGITAL OUT CONT ROL IN OPTICAL AV 1 (RGB) – TV AV 2/AUTO START REC (INPUT 1/DECODER) S-VIDEO VIDEO AUDIO L R COMPON ENT VIDEO OUT Y P B P R IN OUT AC IN OUTPUT S-VIDEO VIDEO AUDIO L R INPUT 3 ANTENNA S-VIDEO INPUT COMPONENT VIDEO INPUT AUDIO INPUT 1 2 DVR-433H_UK.book 15 ページ ２００５年３月１日　火曜日　午後５時６分
Connecting up 02 16 En Connecting to a cable box, satellite receiver or digital terrestrial receiver If you have a cable, satellite or digital terrestrial receiver with a built-in decoder, connect it to this recorder and your TV as shown on this page. 1 If you are using a separate decoder box for your cable/satellite TV, set up following the instructions on the next page. Using the setup on this page you can: • Record any channel by selecting it on the cable box, satellite receiver or digital terrestrial receiver. Important • Do not connect this recorder to your TV ‘through’ your VCR, satellite receiver or other component. Always connect each component directly to your TV or AV amplifier/receiver. 1 Connect RF antenna cables as shown. This enables you to watch and record TV channels. 2 Use a SCART cable (not supplied) to connect the AV1(RGB)-TV AV connector to a SCART AV connector on your TV. This enables you to watch discs. 3 Use another SCART cable to connect the AV2/ AUTO START REC(INPUT 1/DECODER) AV connector to a SCART AV connector on your cable box/satellite/ digital terrestrial receiver. This enables you to record scrambled TV channels. Tip • This recorder has a ‘through’ function which allows you to record a TV program from the built-in TV tuner in this recorder while watching a video playing on your VCR. (To use this feature when the recorder is in standby, Power Save must be set to Off —see Power Save on page 92). Note 1 The diagram shows SCART video connections, but you can alternatively use any of the other audio/video connections. TV Sat ellite dish/ antenna/cable T V wa ll outlet DIGITAL OUT CONT ROL IN OPTICAL AV 1 (RGB) – TV AV 2/AUTO START REC (INPUT 1/DECODER) S-VIDEO VIDEO AUDIO L R COMPON ENT VIDEO OUT Y P B P R IN OUT AC IN OUTPUT S-VIDEO VIDEO AUDIO L R INPUT 3 ANTENNA Cable/Satellite/ Digital T errestrial receiver SCART AV CONNECTOR SCART AV CONNECTOR ANTENNA IN ANTENNA IN (RF IN) ANTENNA OUT ANTENNA OUT ANTENNA IN 1 1 2 3 1 DVR-433H_UK.book 16 ページ ２００５年３月１日　火曜日　午後５時６分
Connecting up 02 17 En Connecting an external decoder box (1) If you have an external, dedicated decoder box for your satellite or cable TV system, use the setup described on this page. Important • Do not connect your decoder box directly to this recorder. • Information from the decoder (for example, relating to pay TV services), is only viewable when this recorder is off (in standby). • For timer recording to work properly on this recorder, the VCR/satellite receiver/cable box must also be switched on during recording. • It is not possible to watch one TV program and record another using this setup. 1 Connect the cable from the antenna/cable TV outlet to the antenna input on your VCR/satellite receiver/cable box. 2 Use a SCART cable (not supplied) to connect your decoder to your VCR/satellite receiver/cable box. See the manual for your decoder box for more detailed instructions. 3 Use a SCART cable to connect your VCR/satellite receiver/cable box to the AV2/AUTO START REC(INPUT 1/DECODER) AV connector on this recorder. 4 Use a SCART cable to connect the AV1(RGB)-TV AV connector to your TV. TV Antenna/cable TV wall outlet VCR/Satellite receiver /Cable box DIGITAL OUT CONT ROL IN OPTICAL AV 1 (R GB) – TV AV 2/AUTO START REC (INPUT 1/DECODER) S-VIDEO VIDEO AU DIO L R COMPON ENT VIDEO OUT Y P B P R IN OUT AC IN OUTPUT S-VIDEO VIDEO AU DIO L R INPUT 3 ANTENNA Decoder SCART AV CONNECTOR SCART AV CONNECTOR SCART AV CONNECTOR ANTENNA IN 1 4 2 3 DVR-433H_UK.book 17 ページ ２００５年３月１日　火曜日　午後５時６分
Connecting up 02 18 En Connecting an external decoder box (2) If you only have a decoder, connect it to this recorder and your TV as shown on this page. 1 Using the setup on this page you can: • Record scrambled channels received using the recorder’s built-in TV tuner. Important • Do not connect this recorder ‘through’ your VCR, satellite receiver or cable box. Always connect each component directly to your TV or AV amplifier/receiver. 1 Connect RF antenna cables as shown. This enables you to watch and record TV channels. 2 Use a SCART cable (not supplied) to connect the AV1(RGB)-TV AV connector to a SCART AV connector on your TV. This enables you to watch discs. 3 Use another SCART cable to connect the AV2/ AUTO START REC(INPUT 1/DECODER) AV connector to a SCART AV connector on your decoder box. This enables you to record scrambled TV channels. Note 1 In order to use this setup, you will need to make the following settings from the Initial Setup menu: • Set the AV2/L1 In setting to Decoder from the Initial Setup menu (see AV2/L1 In on page 94). • From the Manual CH Setting screen, set the Decoder setting for the scrambled channels to On (see Manual CH Setting on page 93). TV Antenna/cable TV wa ll outlet DIGITAL OUT CONT ROL IN OPTICAL AV 1 (RGB) – TV AV 2/AUTO START REC (INPUT 1/DECODER) S-VIDEO VIDEO AU DIO L R COMPON ENT VIDEO OUT Y P B P R IN OUT AC IN OUTPUT S-VIDEO VIDEO AUDIO L R INPUT 3 ANTENNA Decoder SCART AV CONNECTOR SCART AV CONNECTOR ANTENNA IN ANTENNA IN (RF IN) ANTENNA OUT 1 2 3 1 DVR-433H_UK.book 18 ページ ２００５年３月１日　火曜日　午後５時６分
Connecting up 02 19 En Connecting to an AV amplifier/receiver To enjoy multichannel surround sound you need to connect this recorder to an AV amplifier/receiver using the digital optical output. In addition to a digital connection, we recommend also connecting using the stereo analog connection for compatibility with all discs and sources. You’ll probably also want to connect a video output to your AV amplifier/receiver. Use the ordinary video output (as shown here), or the S-video output. Important • Noise may be output from your speakers if the recorder is not set up to work with your AV amplifier/receiver properly (see Audio Out Settings on page 95). 1 Connect RF antenna cables as shown. This enables you to watch and record TV channels. 2 Connect one of the DIGITAL OUT OPTICAL jack on this recorder to an optical digital input on your AV amplifier/receiver. This enables you to listen to multichannel surround sound. 3 Connect the analog AUDIO OUTPUT and VIDEO OUTPUT jacks on this recorder to an analog audio and video input on your AV amplifier/receiver. 4 Connect the AV amplifier/receiver’s video output to a video input on your TV. Important • Do not connect this recorder to your TV ‘through’ your VCR using A/V cables. Always connect it directly to your TV. TV AV amp/ receiver DIGITAL OUT CONT ROL IN OPTICAL AV 1 (RGB) – TV AV 2/AUTO START REC (INPUT 1/DECODER) S-VIDEO VIDEO AUDIO L R COMPON ENT VIDEO OUT Y P B P R IN OUT AC IN OUTPUT S-VIDEO VIDEO AUDIO L R INPUT 3 ANTENNA Antenna/cable TV wa ll outlet ANTENNA IN VIDEO IN DIGITAL IN AUDIO/VIDEO IN VIDEO OUT 1 3 2 1 4 ANTENNA IN (RF IN) ANTENNA OUT DVR-433H_UK.book 19 ページ ２００５年３月１日　火曜日　午後５時６分
Connecting up 02 20 En Connecting other AV sources Connecting a VCR or analog camcorder 1 Connect a set of audio and video inputs of your VCR or camcorder to a set of outputs on this recorder. This enables you to record from this recorder to your VCR or camcorder. • You can use standard video or S-video cables for the video connection. • Alternatively, you can use the AV2/AUTO START REC(INPUT 1/DECODER) SCART connector for audio/video input and output with just one SCART cable. 2 Connect a set of audio and video outputs of your VCR or camcorder to a set of inputs on this recorder. This enables you to record tapes from your VCR or camcorder. • You can use standard video or S-video cables for the video connection. • The front panel connections make convenient connections for a camcorder input. Connecting a DV camcorder Using the front panel DV IN jack, it is possible to connect a DV camcorder or video deck, or DVD-R/RW recorder and digitally transfer DV tapes or DVD-R/RW discs to DVD-R/RW. Important • This jack is for connection to DV equipment only. It is not compatible with digital satellite receivers or D- VHS video decks. 1 Use a DV cable (not supplied) to connect the DV jack of your DV camcorder/video deck to the front panel DV IN jack of this recorder. Plugging in After checking all the connections, plug in the recorder. 1 Use the supplied power cable to connect this recorder to a power outlet. Analog camcorder VCR  HDD/DVD MENU TOP MENU RETURN ENTER HOME MENU ONE TOUCH COPY  OPEN/CLOSE  PULL - OPEN     REC  STANDBY/ON AUDIO/VIDEO OUTPUT AUDIO/VIDEO INPUT 1 2 AUDIO/VIDEO INPUT AUDIO/VIDEO OUTPUT DV camcorder  HDD/DVD MENU TOP MENU RETURN ENTER HOME MENU ONE TOUCH COPY  OPEN/CLOSE  PULL - OPEN     REC  STANDBY/ON DV OUT DV IN DVR-433H_UK.book 20 ページ ２００５年３月１日　火曜日　午後５時６分
Controls and displays 03 21 En Chapter 3 Controls and displays Front panel 1  STANDBY/ON Press to switch the recorder on/into standby. 2 Disc tray 3 DISC NAVIGATOR/TOP MENU Press to display the Disc Navigator screen, or the top menu if a DVD-Video disc is loaded. 4  OPEN/CLOSE Press to open/close the disc tray. 5 HDD/DVD indicator Lights blue when the HDD is selected; orange when DVD is selected. 6 HDD/DVD Press to switch between the hard disk drive (HDD) and DVD for recording and playback. 7 MENU Press to display a DVD-Video disc menu. 8 Front panel display and IR remote sensor See Display on page 24 for details. 9 Front panel inputs (page 12) Pull the cover down where indicated to access the front panel input jacks (audio, video and DV). Especially convenient for connecting camcorders and other portable equipment. 10 ONE TOUCH COPY (page 63) Press to start One Touch Copy of the currently playing title to DVD or the HDD. See also the Note on copying on page 7. 11  Press to stop recording. 12  REC Press to start recording. Press repeatedly to set the recording time in 30 minute blocks. 13 RETURN Press to go back one level in the on-screen menu or display. 14 /// and ENTER Used to navigate all on-screen displays. Press ENTER to select the currently highlighted option. When stopped, the / buttons can also be used to change the TV channel. 15 HOME MENU (page 34) Press to display the Home Menu, from which you can navigate all the functions of the recorder. 16  Press to start or restart playback. 17  Press to pause or resume playback. 18  Press to stop playback.  HDD/DVD MENU T OP MENU RETURN ENTER HOME MENU ONE TOUCH COPY  OPEN/CLOSE  PULL - OPEN     REC  STANDBY/ON 4 5 3 7 1 2 6 8 18 17 16 15 14 13 12 11 10 9 DVR-433H_UK.book 21 ページ ２００５年３月１日　火曜日　午後５時６分
Controls and displays 03 22 En Remote control 1  STANDBY/ON Press to switch the recorder on/into standby. 2 HDD/DVD (page 27) Press to select the hard disk (HDD) or DVD for recording or playback. 3 HELP Press for help on how to use the current GUI screen. DISPLAY (SHIFT HELP) (page 34) Displays/changes the on-screen information displays. 4 INPUT SELECT (page 48) Press to change the input to use for recording. TV/DVD (SHIFT INPUT SELECT ) (page 30) Press to switch between ‘TV mode’, in which you get the picture and sound from the TV’s tuner, and ‘DVD mode’, in which you get picture and sound from the recorder’s tuner (or an external input). 5 Number buttons Use the number buttons for track/chapter/title selection; channel selection, and so on. The same buttons can also be used to enter names for titles, discs and so on. AUDIO (SHIFT 1) (page 29, 61) Changes the audio language or channel. (When the recorder is stopped, press to change the tuner audio.) SUBTITLE (SHIFT 2) (page 60) Displays/changes the subtitles included in multilingual DVD-Video discs. ANGLE (SHIFT 3) (page 62) Switches camera angles on discs with multi-angle scenes. 6 CLEAR Use to clear an entry and start again. 7 CHANNEL /– (page 29) Press to change the channel of the built-in TV tuner. 8 DISC NAVIGATOR (page 54, 73) / TOP MENU (page 32) Press to display the Disc Navigator screen, or the top menu if a DVD-Video disc is loaded. 9 VIDEO Plus (SHIFT MENU) (page 43) / MENU (page 32) Press to set a timer program using VIDEO Plus , or display the disc menu if a DVD-Video disc is loaded. 10 /// and ENTER Used to navigate all on-screen displays. Press ENTER to select the currently highlighted option. 11 HOME MENU (page 34) Press to display the Home Menu, from which you can navigate all the functions of the recorder. 12 RETURN (page 98) Press to go back one level in the on-screen menu or display. Also used for setting the remote control mode. 13 Playback controls (page 31)  /  (page 56) Press to start reverse or forward scanning. Press again to change the speed.  Press to start playback.  Press to pause playback or recording.  Press to stop playback. DVD RECORDER STANDBY/ON TOP MENU MENU DISC NAVIGA TOR HOME MENU HDD/DVD TV/DVD DISPLAY RETURN AUDIO HELP CLEAR INPUT SELECT SUBTITLE ANGLE VIDEO Plus CHANNEL SKIP TV DRECT REC ENTER REC MODE ST0P REC REC ONE TOUCH COPY BACK CM     SHIFT 1 2 4 9 12 3 5 11 13 15 10 14 6 7 16 8 DVR-433H_UK.book 22 ページ ２００５年３月１日　火曜日　午後５時６分
Controls and displays 03 23 En REC MODE (SHIFT  ) (page 39) Press repeatedly to change the recording mode (picture quality).  /  Press to skip to the previous or next title/chapter/ track/folder; or to display the previous or next menu page. CM BACK (SHIFT  ) (commercial back) Press repeatedly to skip progressively backward through the audio or video playing. CM SKIP (SHIFT  ) (commercial skip) Press repeatedly to skip progressively forward through the audio or video playing. / / / (page 56) While paused, press and hold to start slow-motion playback. Press repeatedly to change the playback speed. While paused, press to advance a single frame in either direction. 14 SHIFT Hold down SHIFT to access the functions on the remote printed in green. For example, press and hold SHIFT, then press  for REC MODE . 15 ONE TOUCH COPY (page 63) Press to start One Touch Copy of the currently playing title to DVD or the HDD. 16 Recording controls (page 28)  STOP REC Press to stop recording.  REC Press to start recording. Press repeatedly to set the recording time in blocks of 30 mins. TV DIRECT REC (SHIFT  REC) (page 40) Press to start recording whatever channel your TV is set to. DVR-433H_UK.book 23 ページ ２００５年３月１日　火曜日　午後５時６分
Controls and displays 03 24 En Display 1  Lights during playback; blinks when playback is paused. 2  Lights when copying. 3  Lights during recording; blinks when recording is paused. 4 (page 41) Lights when a timer recording has been set. (Indicator blinks if the timer has been set to DVD but there isn’t a recordable disc loaded, or the timer has been set to HDD but the HDD is not recordable.) NTSC Lights when playing NTSC format video. (page 95) Indicates which channels of a bilingual broadcast are recorded. (page 94) Lights when the component video output is set to progressive scan. OVER (page 95) Lights when the analog audio input level is too high. 5 Recording quality indicators (page 38) XP Lights when the recording mode is set to XP (best quality). SP Lights when the recording mode is set to SP (standard play). LP / SLP Lights when the recording mode is set to LP (long play) or SLP (super long play). EP / SEP Lights when the recording mode is set to EP (extended play) or SEP (super extended play). MN Lights when the recording mode is set to MN (manual recording level) mode. 6 Character display 7R / RW Indicates the type of recordable DVD loaded: DVD-R or DVD-RW. 8 AUTO Lights when Auto Start Recording has been set, and during Auto Start Recording. 9 PL (page 73) Lights when a VR mode disc is loaded and the recorder is in Play List mode. 2 3 (page 98) Shows the remote control mode (if nothing is displayed, the remote control mode is 1). V Lights when an unfinalized Video mode disc is loaded. P R L 9 7 8 2 4 3 5 6 1 DVR-433H_UK.book 24 ページ ２００５年３月１日　火曜日　午後５時６分
Getting started 04 25 En Chapter 4 Getting started Switching on and setting up When you switch the recorder on for the first time, you can make several basic settings using the Setup Navigator feature. This takes you through setting the clock, the internal TV tuner and the video output settings. If you’re using the recorder for the first time, we strongly recommend you use the Setup Navigator before starting to use the recorder. 1 Switch on your TV and set the video input to this recorder. 2 Press the  STANDBY/ON button on the remote control or the front panel to switch on. When you switch on for the first time, your TV should display the Setup Navigator screen. (If the Setup Navigator doesn’t appear, you can also access it from the Initial Setup menu; see page 92). • If this recorder is connected to a compatible TV using a fully-wired 21-pin SCART cable, the recorder will take a few seconds to download country, TV screen size and language information. (Check the manual that came with your TV for compatibility information.) 3 Use the / buttons to choose a language, then press ENTER. 4 Press ENTER to start setting up using the Setup Navigator. • If you don’t want to use the Setup Navigator, press  to select Cancel , then press ENTER to exit the Setup Navigator. 5 Select the Auto Channel Setting (‘ Auto Scan’ or ‘Download from TV’), or ‘Do not set’, then press ENTER. • Select Do not set if you want to skip setting up the channels (because they have already been set up, for example). • You can only use the Download from TV feature if you connected this recorder to your TV using a fully-wired 21-pin SCART cable connected to the AV1(RGB)-TV connector, and if your TV supports this function (check your TV’s instruction manual for more details). STANDBY/ON TOP MENU MENU DISC NAVIGA TOR HOME MENU HDD/DVD TV/DVD DISPLAY RETURN AUDIO HELP CLEAR INPUT SELECT SUBTITLE ANGLE S HOW V IEW CHANNEL ENTER    Initial Setup Basic T uner Video In/Out Audio In Audio Out Language Recording Playback Clock Setting Input Line System Power Save Help Setup Navigator Setup Navigator Language français Italiano Nederlands Pycc English Deutsch Español Svenska K N N Basic Initial Setup Basic T uner Video In/Out Audio In Audio Out Language Recording Playback Clock Setting Input Line System Power Save Help Setup Navigator Setup Navigator Basic Start Cancel Start Complete this setup before you start using your recorder . Please use the Initial Setup if you want to make more detailed settings. Initial Setup Basic T uner Video In/Out Audio In Audio Out Language Recording Playback Clock Setting Input Line System Power Save Help Setup Navigator Setup Navigator Basic Auto Channel Setting English Download from TV Do not Set Auto Scan DVR-433H_UK.book 25 ページ ２００５年３月１日　火曜日　午後５時６分
Getting started 04 26 En • Use the / buttons to choose your country, then press ENTER. • Auto-tuning channels The Auto Scan option automatically scans and sets the channel presets. • Downloading channels from your TV Use the Download from TV option to download all the channels that your TV is tuned to. 6 Select ‘Auto’ for automatic time setting, or ‘Manual’ to set the clock manually, then press ENTER. • Auto clock setting Some TV channels broadcast time signals together with the program. This recorder can use these signals to set the clock automatically. Set ‘Clock Set CH‘ to the channel preset number that broadcasts a time signal, then move the cursor down to ‘Start’ and press ENTER. The recorder takes a short while to set the time. After you see that the time has been set, select Next to proceed. If the time could not be set automatically, press RETURN to go back to the previous screen and select Manual . • Manual clock setting If no stations in your area are broadcasting time signals, you can set the clock manually. Use the / buttons to set your time zone. You can set this by selecting a city or a time relative to GMT. Press  then use the / buttons to select ‘On’ or ‘Off’ for summer time, then press ENTER. Select On if you are currently using summer time. Set the date (day/month/year) and time, then press ENTER to make all the settings. Use the / buttons to change the value in the highlighted field. Initial Setup Basic T uner Video Out Audio In Audio Out Language Recording Playback Clock Setting Input Line System Power Save Help Setup Navigator Setup Navigator Basic Initial Setup Basic T uner Video In/Out Audio In Audio Out Language Recording Playback Clock Setting Input Line System Power Save Help Setup Navigator Setup Navigator Basic Country Selection Country UK Tu n ing 32/213 Cancel Downloading Pr 5 32/213 Cancel Initial Setup Basic T uner Video In/Out Audio In Audio Out Language Recording Playback Clock Setting Input Line System Power Save Help Setup Navigator Setup Navigator Basic Clock Setting Auto Manual Auto Initial Setup Basic T uner Video In/Out Audio In Audio Out Language Recording Playback Clock Setting Input Line System Power Save Help Setup Navigator Setup Navigator Basic Auto Clock Setting Date T ime Clock Set CH –– / –– / –––– –– : –– Pr 1 Start Initial Setup Basic T uner Video In/Out Audio In Audio Out Language Recording Playback Clock Setting Input Line System Power Save Help Setup Navigator Setup Navigator Basic Auto Clock Setting Date T ime Clock Set CH SAT 01 / 01 / 2005 11 : 20 Pr 1 Start Next Initial Setup Basic T uner Video In/Out Audio In Audio Out Language Recording Playback Clock Setting Input Line System Power Save Help Setup Navigator Setup Navigator Basic Manual Clock Setting T ime Zone Summer Time Off England London 1/2 Initial Setup Basic T uner Video In/Out Audio In Audio Out Language Recording Playback Clock Setting Input Line System Power Save Help Setup Navigator Setup Navigator Basic Manual Clock Setting T ime Zone Summer Time On England London 1/2 Initial Setup Basic T uner Video In/Out Audio In Audio Out Language Recording Playback Clock Setting Input Line System Power Save Help Setup Navigator Setup Navigator Basic Manual Clock Setting Date T ime T ime Zone Summer Time On England London 01 / / 01 00 : 00 2005 SAT 2/2 DVR-433H_UK.book 26 ページ ２００５年３月１日　火曜日　午後５時６分
Getting started 04 27 En Use the / buttons to move from one field to another. • You can go back to the previous screen at anytime in the Setup Navigator by pressing RETURN . 7 Select the TV screen type, ‘Wide (16:9)’ or ‘Standard (4:3)’. Use the / buttons to select, then press ENTER . 8 Is your TV compatible with progressive scan video? Use the / buttons to select Compatible , Not Compatible , or Don’t Know , then press ENTER . • Note that progressive scan video is only output through the AV1(RGB)-TV connector and the component video outputs. 9 Press ENTER to exit the Setup Navigator, or select ‘Go Back’ if you want to start again. That completes basic setup using the Setup Navigator. Other settings you can make After setting up using the Setup Navigator, you should be ready to start enjoying your DVD recorder. It’s possible, however, that you may want to make a couple of additional settings, depending on how the recorder is set up for terrestrial TV broadcasts. • Manual channel setting – This setting lets you skip channels where there is no station, as well as manually tune to stations. See Manual CH Setting on page 93. • If for any reason you need to cancel the setup process before it’s completed, you will be asked the next time you switch on whether you want to start setting up again, or whether to leave it until later. Selecting the hard disk or DVD for playback and recording The HDD/DVD button (remote control and front panel) is used to select the hard disk (HDD) or DVD for playback and recording. The indicator in the front panel display shows which is currently selected. Initial Setup Basic T uner Video In/Out Audio In Audio Out Language Recording Playback Clock Setting Input Line System Power Save Help Setup Navigator Setup Navigator Basic TV Screen Size Wide (16:9) Standard (4:3) Initial Setup Basic T uner Video In/Out Audio In Audio Out Language Recording Playback Clock Setting Input Line System Power Save Help Setup Navigator Setup Navigator Basic Progressive Compatible Not Compatible Don't Know Not Compatible Initial Setup Basic T uner Video In/Out Audio In Audio Out Language Recording Playback Clock Setting Input Line System Power Save Help Setup Navigator Setup Navigator Basic Setup is complete! Enjoy using your DVD recorder! Finish Setup Go Back Finish Setup STANDBY/ON HDD/DVD TV/DVD DISPLAY AUDIO HELP CLEAR INPUT SELECT SUBTITLE ANGLE CHANNEL  DVR-433H_UK.book 27 ページ ２００５年３月１日　火曜日　午後５時６分
Getting started 04 28 En Making your first recording This quick guide shows you how to make a basic recording of a TV program on either the HDD, or to a recordable DVD. Recording is covered in much more detail in chapter 5 ( Recording ). 1 If they aren’t already on, switch on your TV and this recorder. Press  STANDBY/ON to switch on. • Make sure that the video input on your TV is set to this recorder. 2 Use the HDD/DVD button to select the HDD or DVD as the recording destination. If you choose to record to the HDD, skip to step 5 now. 3 Press  OPEN/CLOSE (front panel only) to open the disc tray. 4 Load a blank DVD-R or DVD-RW disc with the label side face-up, using the disc guide to align the disc. • When you load a new, blank DVD-RW disc, the recorder will take a moment to initialize it for recording. • Blank DVD-R discs are ready for Video mode recording out of the box. 5 Use the CHANNEL /– buttons to select the TV channel you want to record from. • Channel presets are numbered 1–99. • If the recorder is connected to your TV using a SCART cable and your TV supports Direct Recording, it’s possible to quickly start recording whatever channel your TV is tuned to. See Direct recording from TV on page 40 for detailed instructions. 6 Press  REC to start recording. • By default, the recording will be in SP (standard play) mode, which will give you around two hours of recording from a blank DVD disc. The different recording modes and their recommended uses are covered in more detail in the chapter on Recording. • You can pause recording by pressing  . Press  REC or  again to restart recording. 7 When you want to stop recording, press  STOP REC. Playing back your recording The TV program you just recorded should be on the HDD or DVD disc as a single title with one or more chapters. • Press  to start playback. If you want to stop playback before the end of the recording, press  . DVD RECORDER STANDBY/ON TOP MENU MENU DISC NAVIGA TOR HOME MENU HDD/DVD TV/DVD DISPLAY RETURN AUDIO HELP CLEAR INPUT SELECT SUBTITLE ANGLE S HOW V IEW CHANNEL SKIP TV DRECT REC ENTER REC MODE ST0P REC REC SHIFT ONE TOUCH COPY BACK CM     DVR-433H_UK.book 28 ページ ２００５年３月１日　火曜日　午後５時６分
Getting started 04 29 En Using the built-in TV tuner Changing TV channels There are three different ways to select TV channels. Note that you can’t change the TV channel during playback, recording or during recording standby. • CHANNEL /– buttons on the remote • Number buttons on the remote – For example, to select channel 4, press 4 then ENTER ; for channel 34, press 3 , 4 , ENTER . 1 Changing audio channels You can change the audio channel of the broadcast or external input signal. • Press AUDIO (SHIFT 1) to change the audio. The current audio channel is displayed on-screen. • If the NICAM audio setting (see Nicam Select on page 94) is set to NICAM and you are watching a NICAM broadcast, you can switch between NICAM and Regular (non-NICAM) audio. • If the NICAM broadcast is bilingual, you can also select the language. • You can also select the language for a non-NICAM bilingual broadcast. • When watching a recording made from an external input with Bilingual recording selected (see External Audio on page 94), you can switch the audio channel between left ( L ), right ( R ) or both ( L R ). Tip • When recording to the HDD with HDD Recording Format set to Video Mode On, to DVD in Video mode, or on the LPCM setting, only one channel of a bilingual broadcast is recorded. In this case, decide which language you want to record before recording by setting the Bilingual Recording setting (see Bilingual Recording on page 95). Note 1. Channel presets are numbered 1–99. TOP MENU MENU DISC NAVIGA TOR HOME MENU TV/DVD DISPLAY RETURN AUDIO HELP CLEAR INPUT SELECT SUBTITLE ANGLE S HOW V IEW CHANNEL ENTER TOP MENU MENU DISC NAVIGA TOR HOME MENU TV/DVD DISPLAY RETURN AUDIO HELP CLEAR INPUT SELECT SUBTITLE ANGLE S HOW V IEW CHANNEL SKIP TV DRECT REC ENTER REC MODE ST0P REC REC SHIFT ONE TOUCH COPY BACK CM    NICAM Regular NICAM A NICAM B Regular NICAM A B A (L) B (R) A B (L R) LR L R DVR-433H_UK.book 29 ページ ２００５年３月１日　火曜日　午後５時６分
Getting started 04 30 En Switching between TV and DVD When the recorder is stopped or recording you can choose whether to have the audio/video from the built-in TV tuner (or external input) play on your TV (‘DVD mode’), or watch the channel that the TV is currently set to (‘TV mode’). During playback or when a menu is being displayed on- screen, the sound and video is always routed to your TV and is unaffected by the TV/DVD ( SHIFT INPUT SELECT ) mode setting. Note that the recorder must be connected to your TV using a SCART cable to be able to use this feature. • Press TV/DVD (SHIFT INPUT SELECT ) to switch between TV mode and DVD mode. STANDBY/ON TOP MENU MENU DISC NAVIGA TOR HOME MENU HDD/DVD TV/DVD DISPLAY RETURN AUDIO HELP CLEAR INPUT SELECT SUBTITLE ANGLE S HOW V IEW SKIP TV DRECT REC REC MODE ST0P REC REC SHIFT ONE TOUCH COPY BACK CM    CHANNEL ENTER  DVR-433H_UK.book 30 ページ ２００５年３月１日　火曜日　午後５時６分
Getting started 04 31 En Basic playback This section shows you how to use your recorder for playback of discs (DVD, CD, etc.), and for playback of video from the HDD. More playback features, such as repeat and program play, are covered in Playback on page 53. Important • Throughout this manual, the term ‘DVD’ means playback-only DVD-Video discs and DVD-R/RW. If a function is specific to a particular kind of DVD disc, it is specified. • Some DVD-Video discs don’t allow certain playback controls to operate at certain points in the disc. This is not a malfunction. 1 Press  STANDBY/ON to switch on. Also turn on your TV and make sure that it is set to the correct video input. 2 Press HDD/DVD to select either the HDD or the DVD for playback. If playing video from the HDD, skip to step 5 below. 3 Press  OPEN/CLOSE (front panel only) to open the disc tray. 4 Load a disc. Load a disc with the label side facing up, using the disc tray guide to align the disc (if you’re loading a double- sided DVD-Video disc, load it with the side you want to play face down). • If you want to play a DTS audio CD, please first read the note on page 33. 5 Press  to start playback. • If you’re playing a DVD-Video or Video CD, a disc menu may appear when you start playback. Use the /// buttons and ENTER to navigate DVD disc menus, and the number buttons and ENTER for Video CD menus. • When playing video from the HDD, playback will automatically stop after the end of a title is reached. • See the following sections for more details on playing specific kinds of discs. 6 To stop playback, press  . 7 When you’ve finished using the recorder, eject the disc and switch the recorder back into standby. • To open/close the disc tray, press  OPEN/CLOSE (front panel). Remove the disc before putting the recorder into standby. • Press  STANDBY/ON to switch the recorder into standby. STANDBY/ON TOP MENU MENU DISC NAVIGA TOR HOME MENU HDD/DVD TV/DVD DISPLAY RETURN AUDIO HELP CLEAR INPUT SELECT SUBTITLE ANGLE S HOW V IEW CHANNEL SKIP TV DRECT REC ENTER REC MODE ST0P REC REC SHIFT ONE TOUCH COPY BACK CM     DVR-433H_UK.book 31 ページ ２００５年３月１日　火曜日　午後５時６分
Getting started 04 32 En Playing DVD discs The table below shows the basic playback controls for DVD-Video, and recordable DVD discs. Playing from the HDD The table below shows the basic playback controls when playing video recorded on the hard disk (HDD). P ress to start playback. If RESUME is displayed on-screen, play- back starts from the place last stopped. P ress to stop playback. Y ou can resume playback from the same point by pressing  . (P ress  again to cancel the resume function.) P auses playback, or restarts playback when paused. P ress to start scanning. P ress repeatedly to increase the scanning speed. P ress to skip to previous/next chapter/title. Except VR mode: During playback, enter a chapter number then press ENTER to skip directly to that chapter within the currently playing title. On some discs, you can also use the num- ber buttons to select numbered items in the disc menu. VR mode only: During playback, enter a title number then press ENTER . All: P ress CLEAR to clear a number entr y and start again. (Commercial back/skip) Each press skips backward/forward progressively up to a maximum of ten minutes forward or three minutes back. While paused, press and hold to start slow-motion playback. P ress repeatedly to change the playback speed. While paused, press to advance a single frame in either direction. P ress to display the menu of a DVD-V ideo disc. Use the cursor buttons to navigate DVD- Video disc menus; press ENTER to select items. P ress to return to the previous level of a DVD-V ideo disc menu. ENTER SHIFT SKIP BACK CM   TOP MENU MENU ENTER RETURN P ress to start playback. If RESUME is displayed on-screen, play- back starts from the place last stopped. Playback automatically stops after the end of a title is reached. P ress to stop playback. Y ou can resume playback from the same point by pressing  . (P ress  again to cancel the resume function.) P auses playback, or restarts playback when paused. P ress to start scanning. P ress repeatedly to increase the scanning speed. P ress to skip to previous/next chapter/title. During playback, enter a title number then press ENTER to skip directly to that title. P ress CLEAR to clear a number entr y and start again. (Commercial back/skip) Each press skips backward/forward progressively up to a maximum of ten minutes forward or three minutes back. While paused, press and hold to start slow-motion playback. P ress repeatedly to change the playback speed. While paused, press to advance a single frame in either direction. ENTER SHIFT SKIP BACK CM   DVR-433H_UK.book 32 ページ ２００５年３月１日　火曜日　午後５時６分
Getting started 04 33 En Playing CDs and WMA/MP3 discs The table below shows the basic playback controls for audio CDs 1 , and WMA/MP3 files. Playing Video CD/Super VCDs The table below shows the basic playback controls for Video CD/Super VCDs. Some discs feature Playback Control (PBC for short) menus. These discs show PBC in the display when you load them and display a menu on-screen from where you can select what to watch. 2 P ress to start playback. P ress to stop playback. P auses playback, or restarts playback when paused. P ress to start scanning. P ress again to increase the scanning speed. (There are two scan speeds; the current scan speed is shown on-screen.) P ress to skip to previous/next track (or folder for WMA/MP3 disc). During playback, enter a track number then press ENTER to skip directly to that track. P ress CLEAR to clear a number entr y and start again. Note 1. If you want to play a DTS audio CD, make sure the recorder is connected to a DTS-compatible amp/receiver with a digital connection. Noise will be output through the analog outputs. Also make sure that STEREO is selected using the AUDIO ( SHIFT 1 ) button (see Switching audio channels on page 61). ENTER P ress to start playback. Video CD only: If RESUME is displayed on- screen, playback starts from the place last stopped. P ress to stop playback. Video CD only: Y ou can resume playback from the same point by pressing  . (P ress  again to cancel the resume function.) P auses playback, or restarts playback when paused. P ress to start scanning. P ress repeatedly to increase the scanning speed. P ress to skip to previous/next track. When a PBC menu is displayed, press to display the previous/next page. During playback, enter a track number then press ENTER to skip directly to that track. P ress CLEAR to clear a number entr y and start again. While a PBC menu screen is displayed, use to select numbered menu items. Video CD only: Each press skips backward/ forward progressively up to a maximum of ten minutes forward or three minutes back. Note that this function doesn’t work when playing in PBC mode. While paused, press and hold to start slow-motion playback. P ress repeatedly to change the playback speed (forward only). While paused, press to advance a single frame (forward only). P ress to display the disc menu of a Video CD/Super VCD playing in PBC mode. 2. When playing in PBC mode, some playback features, such as search, repeat and program play are not available. You can play a PBC Video CD/Super VCD in non-PBC mode by pressing  to start playback instead of  . ENTER SHIFT SKIP BACK CM   RETURN DVR-433H_UK.book 33 ページ ２００５年３月１日　火曜日　午後５時６分
Getting started 04 34 En Using the Home Menu From the Home Menu screen you can access all the features of the recorder. Note that some options in the Home Menu may be grayed out sometimes, indicating that they are not available at the present time. For example, the Photoviewer option is grayed out unless there is a disc loaded that contains JPEG image files. Press HOME MENU to display the Home Menu screen: Use the /// buttons followed by ENTER to select the option you want. To exit the Home Menu, press HOME MENU . Displaying disc information on- screen You can display various on-screen information about the disc loaded or the HDD. 1 Press DISPLAY (SHIFT HELP) repeatedly to display/change the on-screen information. • Press once to show the HDD and removable disc (DVD, etc.) activity together. Press again to show the status of just the currently selected playback/ recording device (HDD or removable disc). • The on-screen display automatically disappears after 150 minutes. 2 To hide the information display, press DISPLAY (SHIFT HELP) repeatedly until it disappears. The example displays below are a guide only; actual displays vary according to the disc loaded, etc. Home menu options Disc Navigator (page 54, page 73) Disc Setup (page 87) Timer Recording (page 42) Initial Setup (page 92) Play Mode (page 57) Video/Audio Adjust (page 89) Copy (page 63) Photo Viewer (page 85) Jukebox (page 82) T imer Recording Photo Viewer Disc Setup Play Mode Disc Navigator Initial Setup Video/Audio Adjust Copy Jukebox TOP MENU MENU DISC NAVIGA TOR HOME MENU RETURN S HOW V IEW SKIP ENTER REC MODE BACK CM   DVD RECORDER STANDBY/ON TOP MENU MENU DISC NAVIGA TOR HOME MENU HDD/DVD TV/DVD DISPLAY RETURN AUDIO HELP HELP CLEAR INPUT SELECT SUBTITLE ANGLE S HOW V IEW CHANNEL SKIP TV DRECT REC ENTER REC MODE ST0P REC REC SHIFT ONE TOUCH COPY BACK CM     DVR-433H_UK.book 34 ページ ２００５年３月１日　火曜日　午後５時６分
Getting started 04 35 En HDD and removable disc activity display Press DISPLAY ( SHIFT HELP ) once to see the HDD and removable disc (DVD, etc.) activity. Use the HDD/DVD button to switch between the two kinds of display. The example displays below show high-speed copying from HDD to DVD, and HDD chase playback. Stop display 1 1 DVD-RW Original / Play List If a VR mode disc is loaded, this shows whether playback is currently set to Original or Play List . During preview playback of the Copy List, this shows Copy List . 2 Disc type and mode Shows the disc type ( HDD , DVD-R , DVD-RW , CD , etc.), and the disc mode for recordable DVD, if applicable ( VR or Video ). 3 Recording mode and time Shows the current recording mode ( XP , SP , LP , etc.), and the total recording time of the disc. 4 Resume Shows Resume if playback can be resumed from the last place stopped. 5 Recording time remaining Shows the approximate recording time left on the disc in the current recording mode. 6 Preset name and number Shows the preset name and preset number for the currently selected channel. 7 Audio mode Shows the broadcast audio mode for the current channel preset ( Mono , Stereo , etc.). 8 Copy control information Shows recording restrictions of the current channel program. 9 Disc name Shows the disc name. (For CDs, this area shows playable files other than CD audio tracks; for example, Multi-format: WMA/MP3 .) 10 Finalized Shows Finalized if a recordable DVD is finalized. 11 TV/DVD mode Shows the current mode of the recorder (see Switching between TV and DVD on page 30). Stop display 2 1 Date and time 2 Number of titles/tracks on disc For a VR mode DVD-RW, the number of Original and Play List titles are shown separately. Rec Mode SP(2h00m/DVD) HDD Remain 10h35m Stop Remain –h––m Stop Hi-Speed Copy 0h08m left DVD-RW Video Rec Mode SP(2h00m/DVD) HDD Remain 10h35m Chase Play Rec Remain 0h52m Stop DVD-RW Video Relative pla yback position Recording time  Stop DVD-RW VR Original Disc Name : Comedy shows DVD Mode Finalized Resume XP (1h00m/DVD) Rem. 0h35m C opy Once St ereo ABC Pr 1 1 2 8 7 10 9 11 3 6 4 5  Stop DVD-RW VR Original Titles TV Mode : Original 99 Lock Disc : On Play List 15 14:52 MON 15/11/2004 Copy Once Ster eo ABC Pr 1 1 2 DVR-433H_UK.book 35 ページ ２００５年３月１日　火曜日　午後５時６分
Getting started 04 36 En Play display 1 1 Number of chapters in title 2 Current title and chapter number (For CD/Video CD/Super VCD, shows current track; for WMA/MP3, shows current folder and track; for JPEG disc, shows current folder and file.) 3 Elapsed title time (For CD, WMA, MP3, Super VCD, shows elapsed track time; for Video CD, shows elapsed disc time.) 4 Total running time of title 5 Angle indicator Lights during multi-angle scenes. Play display 2 1 Chase playback, simultaneous record/playback, copy, disc back-up Indicates that recording, copying or back-up is in progress. 2 Elapsed chapter time 3 Total running time of chapter 4 Data transfer rate Shows the current data rate being read from the disc. 1 5 Copy protected material (!) Shows ‘ ! ’ if the playback material is copy-once protected. Recording display 1 Current title number 2 Elapsed recording time 3 Timer recording start and stop times Shows the start and stop times if the current recording is a timer recording. 4 Remaining recording time available Shows the amount of space left on the disc in the current recording mode. 5 Recording mode Shows the current recording mode ( XP , SP , LP , etc.), and the total recording time of the disc. Tip • When using the simultaneous play and record feature, the display shows information for playback only. • During real-time copy, the copy source playback information is displayed. • The Video mode disc displays become the same as a DVD-Video disc once the disc is finalized. • The total recording time figure shown in parenthesis is calculated based on a 12cm/4.7GB disc at the displayed record setting. • Recording and playback times for TV recordings are approximately 0.1% shorter than the actual time. This is because of the slightly different frame rates of TV broadcasts versus DVD. • The frame number is shown next to the elapsed time display when the disc is paused. • Copy Once or Can’t Record messages may appear in the stop or recording displays. These indicate that the broadcast TV program contains copy control information. Note 1. Data transfer rate shows the amount of video and audio information recorded on the disc. It is not an indication of picture/audio quality.  Play DVD-R Video DVD Mode Title T otal Ch apters 15 3–2 0. 00. 15 0. 11. 52 5 1 2 3 4  Play DVD-R Video Title Name 21/11 Football match : C hapter T otal  C hapter Time 3–2 0. 00. 15 ! 0. 00. 21 0. 01. 52 4.32Mbps Hi-Speed Copy 5 2 3 4 1  Rec DVD-R Video XP (1h00m/DVD) Rem. 0h35m 21:00 – 22:00 30 . 00. 15 Co py Once DVD Mode St ereo ABC Pr 1 5 1 2 3 4 DVR-433H_UK.book 36 ページ ２００５年３月１日　火曜日　午後５時６分
Recording 05 37 En Chapter 5 Recording About DVD recording This recorder can record on both DVD-R and DVD-RW media. The main difference between the two is that DVD-R discs can only be recorded once, while DVD-RW can be recorded, erased and re-recorded many times. Both types of disc can be initialized for Video mode or VR mode recording. Each has its advantages, and it depends on what you want to do with the recording which mode you choose. If you want to edit your recordings in any significant way, VR mode offers greater possibilities for cutting, copying, and changing the way the video is presented. Video mode is less flexible when it comes to editing, but it has the advantage that it is compatible with standard DVD players (many of which won’t play VR mode discs 1 ). Once a disc is initialized for a particular mode, all recording on that disc will be in that mode. Important • The maximum number of titles and chapters that can be recorded on a VR mode disc is 99 and 999 respectively; on a Video mode disc the maximum number of titles and chapters is 99 and 99. No more recording is possible on a disc that already contains the maximum number of chapters/titles. • Unfinalized Video mode discs are not usable in other DVD recorders. Likewise, unfinalized video mode discs recorded using other recorders are not usable in this recorder. • Pioneer takes no responsibility for recording failure due to power cuts, defective discs, or damage to the recorder. • Fingerprints, dirt and small scratches on a disc can affect playback and/or recording performance. Please take proper care of your discs. • See also Disc / content format playback compatibility on page 9 for detailed disc compatibility information. • Although this recorder can record PAL, SECAM, NTSC and PAL-60, you can’t mix multiple TV line systems on one disc. A disc can contain PAL and SECAM recordings, or NTSC and PAL-60. See also Additional information about the TV system settings on page 99. About HDD recording Recording to the internal hard disk drive (HDD) is very flexible; you have the full choice of recording quality options, including manual mode, and of course you can record, erase and re-record as many times as you like. The capacity of the hard disk drive means that you can store many hours of video on it, even using the higher quality recording modes. Important • The maximum number of titles/chapters per title that can be recorded on the HDD is 999 and 99 respectively. No more recording is possible on the HDD after the maximum number of titles has been reached. • The maximum continuous recording time for one title is 12 hours. • It is possible to record both PAL and NTSC titles on the HDD. Before recording, you need to make sure that the Input Line System setting (page 99) matches the TV line system of the source you’re recording. HDD Video mode compatibility When recording to the HDD you can choose to record in one of two formats. Set the format from the HDD Recording Format item in the Initial Setup menu (see page 97). When set to Video Mode On, high-speed copying from HDD to Video mode DVD is possible. When recording a bilingual broadcast, set which channel you want to record from the Initial Setup menu (see Bilingual Recording on page 95). When HDD Recording Format is set to Video Mode Off, high-speed copying isn’t possible. However, both channels of bilingual broadcasts are recorded and you can switch the audio on playback. Note 1. Some DVD players, such as some Pioneer models, are compatible with VR mode discs. Check the operating instructions for your player for VR mode compatibility information. DVR-433H_UK.book 37 ページ ２００５年３月１日　火曜日　午後５時６分
Recording 05 38 En Recording time and picture quality There are six preset recording quality modes 1 : • XP – High quality setting, gives about one hour of recording time on a DVD disc. • SP (Standard Play) – Default quality, used for most applications, gives about two hours of recording time on a DVD. • LP (Long Play) – Lower video quality than SP, but doubles the recording time on a DVD to about four hours. • EP (Extended Play) – Lower quality than LP, but gives about six hours of recording time on a DVD disc. • SLP (Super Long Play) – Lower quality than EP, but gives about eight hours of recording time on a DVD disc. • SEP (Super Extended Play) – Lowest video quality but gives about ten hours of recording time on a DVD disc. Please note that there is a trade-off between recording time and quality. The longer the possible recording time, the lower the recorded picture quality. In addition to these settings, when Manual Recording is On (see Manual Recording on page 97) you can access 32 different recording quality/time settings ( MN1 – MN32 ), a high-quality audio mode ( LPCM ), and a super-high quality (data transfer rate of around 15 Mbps) HDD recording mode ( XP ). When setting a timer recording there is a further option, AUTO , which maximizes the recording quality for the space available on the disc loaded at the time of recording. (If recording to the HDD, the recording quality is maximized to fit on to a DVD disc.) Recorded audio In all except the LPCM mode, sound is recorded in two channel Dolby Digital format. When set to LPCM , sound is recorded in high quality, uncompressed Linear PCM format. If the broadcast audio is bilingual and you are recording in Video mode or to the HDD with the HDD Recording Format set to Video Mode On, or on the LPCM setting, use the Bilingual Recording setting (page 95) to select the A/L or B/R audio channel to record before recording starts. In other cases, both channels of a bilingual broadcast will be recorded and you can switch on playback. Restrictions on video recording You cannot record copy-protected video using this recorder. Copy-protected video includes DVD-Video discs and some satellite broadcasts. If copy-protected material is encountered during a recording, recording will pause automatically and an error message will be displayed on- screen. Video that is ‘copy-once only’ can only be recorded on the HDD or in VR mode (see below). When recording a TV broadcast or through an external input, you can display copy control information on screen. (see Displaying disc information on-screen on page 34). CPRM CPRM is a copy protection/scrambling system developed for the recording of ‘copy once’ broadcast programs. CPRM stands for Content Protection for Recordable Media . This recorder is CPRM compatible, which means that you can record copy-once broadcast programs, but you cannot then make a copy of those recordings. CPRM recordings can only be made on CPRM-compatible DVD-R (ver. 2.0/8x or higher) or DVD-RW (ver. 1.1 or higher) discs formatted in VR mode or on the HDD. DVD CPRM recordings can only be played on players that are specifically compatible with CPRM. Recording equipment and copyright Recording equipment should be used only for lawful copying and you are advised to check carefully what is lawful copying in the country in which you are making a copy. Copying of copyright material such as films or music is unlawful unless permitted by a legal exception or consented to by the rightowners. • This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. Note 1. All recording times (both in this manual and those shown by the recorder) are approximate. This is because of the way that the video is re- corded; you may get slightly more or slightly less, depending on what you’re recording. DVR-433H_UK.book 38 ページ ２００５年３月１日　火曜日　午後５時６分
Recording 05 39 En Setting the picture quality/recording time Before starting a recording, you will usually want to set the picture quality/recording time. There are six standard settings available, which allow you to choose a balance between picture quality and recording time. When Manual Recording is set to On (see Manual Recording on page 97), a further option will be available ( MN1 – 32 , LPCM or XP , depending on what you set). See also Recording time and picture quality on page 38 for more information. • Press REC MODE (SHIFT  ) repeatedly to select a recording setting. • XP – High quality • SP – Standard play • LP – Long play • EP – Extended play • SLP – Super Long play • SEP – Super Extended play • MN / LPCM 1 / XP 2 – Manual / Linear PCM / XP (available only when manual recording is on) The setting is indicated in the front panel display, and shown on-screen together with the recording time for a blank recordable disc. If a recordable disc is loaded, the approximate remaining recording time for that disc is also shown. (Note that if the On Screen Display setting (see On-Screen Display on page 98) is Off then this information is not displayed.) Basic recording from the TV Follow the instructions below to record a TV program. Recording starts immediately and continues until the disc is full or you stop the recording. 1 Use the HDD/DVD button to select the HDD or a recordable DVD for recording. • If you’re recording to DVD, load a recordable disc (if you load a new blank DVD-RW disc, the recorder takes a short while to initialize the disc). 2 Use the CHANNEL /– buttons to select the TV channel to record. The front panel display shows the channel number: • While the recorder is stopped, you can also use the number buttons on the remote to select the channel. (For channel 6, press 6 then ENTER ; for channel 24, press 2, 4 then ENTER ) 3 Use the REC MODE (SHIFT  ) button to set the picture quality/recording time. • See Setting the picture quality/recording time above for detailed instructions. Note 1. Audio is recorded in 16-bit Linear PCM format, video is recorded at XP quality. When recording a bilingual broadcast, select which audio chan- nel to record (see Bilingual Recording on page 95). 2. Applicable only to HDD recording. (If this setting is used when recording to DVD, MN32 is used.) When copied to DVD, XP recordings are always copied in real time. VR mode Video mode HDD SKIP TV DRECT REC REC MODE ST0P REC REC SHIFT ONE TOUCH COPY BACK CM    VR mode Video mode HDD STANDBY/ON TOP MENU MENU DISC NAVIGA TOR HOME MENU HDD/DVD TV/DVD DISPLAY RETURN AUDIO HELP CLEAR INPUT SELECT SUBTITLE ANGLE S HOW V IEW CHANNEL SKIP TV DRECT REC ENTER REC MODE ST0P REC REC SHIFT ONE TOUCH COPY BACK CM     Channel preset DVR-433H_UK.book 39 ページ ２００５年３月１日　火曜日　午後５時６分
Recording 05 40 En 4 Use the AUDIO (SHIFT 1) button to select the audio channel to record. See Changing audio channels on page 29 for more on this. • When recording in VR mode, if a broadcast is bilingual, both audio channels are recorded, allowing you to switch the audio channel on playback. The only exception to this is when the picture quality is set to LPCM , in which case you do need to select the audio channel before recording. 5 Press  REC to start recording. If you want to set a recording end time, press the  REC button repeatedly. The recording time increases in 30 minute increments, up to a maximum of six hours. The time the recording will end is shown on-screen and in the front panel display. When the recording ends, the recorder automatically switches into standby if no other operation is being performed. • To cancel the set recording time, press  REC . • If you want to pause recording at any time, press  . Press again to restart the recording. (If recording to the HDD or in VR mode, a new chapter is started after recording restarts) 6 To stop the recording, press  STOP REC. • If you set the recording time in the previous step, you can still stop the recording anytime by pressing  STOP REC . • Recording will stop automatically when there is no more space on the HDD/DVD, or after 12 hours of HDD recording (whichever is sooner). Tip • During recording you can turn on/off the SCART loop through function. During recording, press the front panel  button to switch to SCART THRU (loop through on), or  to switch to SCART NORM (loop though off). Note that you can’t switch loop through on if recording from the AV2/AUTO START REC(INPUT 1/DECODER) or AV1(RGB)-TV connectors. Also, loop through is automatically reset to off after recording has finished. Direct recording from TV If you connected this recorder to your TV using a SCART cable, and your TV supports Direct Recording, you can record whatever is currently being shown on the TV without having to worry about what channel preset the recorder is on. Check the instructions that came with your TV if you’re not sure whether your TV supports this feature. 1 If necessary, load a recordable disc. 2 Set the picture quality/recording time using the REC MODE (SHIFT  ) button. 3 Press TV DIRECT REC (SHIFT  REC) to start recording. If you want to set a recording time, press the  REC button repeatedly. The recording time increases in 30 minute increments, up to a maximum of six hours. You can see the recording time on-screen and in the front panel display. When the recording ends, the recorder automatically switches into standby if no other operation is being performed. • To cancel the set recording time, press  REC . • If you want to pause recording at any time, press  . Press again to restart the recording. (If recording to the HDD or in VR mode, a new chapter is started after recording restarts) 4 To stop the recording, press  STOP REC. • If you set the recording time in step 3 , you can still stop the recording anytime by pressing  STOP REC . • Recording will stop automatically when there is no more space on the HDD/DVD, or after 12 hours of HDD recording (whichever is sooner). Tip • You can press TV DIRECT REC ( SHIFT  REC ) while the recorder is in standby to switch on and immediately start recording. • Please note that you can’t record from another component (VCR, etc.) that is connected by a SCART cable to the AV2/AUTO START REC(INPUT 1/ DECODER) connector using the TV Direct Recording feature. DVD RECORDER SKIP TV DRECT REC REC MODE ST0P REC REC SHIFT ONE TOUCH COPY BACK CM    DVR-433H_UK.book 40 ページ ２００５年３月１日　火曜日　午後５時６分
Recording 05 41 En Setting a timer recording Using the timer recording features you can program up to 32 timer recordings up to a month in advance. Timer recording programs can be set to record just once, every day, or every week. There are three ways to program a timer recording; using the Easy Timer Recording feature (see Easy Timer Recording below), using the VIDEO Plus programming system (see Timer recording using the VIDEO Plus ® programming system on page 43), or using manual timer recording (see Setting a manual timer recording on page 44). You can set the recording quality for your timer recording in the same way as for a regular recording, but with the added option of an AUTO mode, which maximizes the recording quality for the space available on the disc (if recording to DVD), or to fit on to a blank DVD disc (if recording to HDD). You can set timer recordings to record to a recordable DVD or to the hard disk drive. For regular (daily or weekly) HDD timer recordings that you don’t need to keep, you can use the Auto Replace Recording feature to automatically replace the previous timer recording with the new one. Note that when you use this feature, the previous recording made on that timer program will be replaced by the next one, regardless of whether you have watched it yet or not. You can also set the recorder so that it will adjust the recording quality to try and fit the recording on to the disc if it would not otherwise fit at the recording quality you set (see Optimized Rec on page 97 for more on this). Finally, if you set a timer recording to record to DVD but there isn’t a recordable DVD loaded at the time of the recording, the Recovery Recording feature will automatically record the program to the HDD for you. Important •A timer recording can’t be set if there are already 32 timer programs waiting to be recorded. • Timer recording will not start if: – The recorder is already recording. – A disc is being initialized, finalized or unfinalized. • Timer recording will start when the operation preventing timer recording has finished. • If a recordable DVD that doesn’t support simultaneous playback and recording (see Simultaneous recording and playback on page 48) is playing when a DVD timer recording is due to start, playback will automatically stop to allow the recording to start. • The timer indicator ( ) lights in the front panel display when the timer is active. If the indicator is blinking it means that (for a DVD timer recording) there is no disc loaded, or the disc loaded is not recordable (for an HDD timer recording it means that the HDD is not recordable). • Approximately two minutes before a timer recording is set to start, the recorder will go into timer recording standby. In timer recording standby you cannot use some functions. • The maximum length for timer recordings made to the HDD is 24 hours. However, because one title (HDD) is limited to 12 hours, recordings over 12 hours will be spread over two titles. Note that there will be a break in the recording of a few seconds between titles. VR mode Video mode HDD DVR-433H_UK.book 41 ページ ２００５年３月１日　火曜日　午後５時６分
Recording 05 42 En Easy Timer Recording As the name suggests, Easy Timer Recording makes setting up a timer recording as simple as possible. 1 Press HOME MENU, select ‘Timer Recording’, then ‘Easy Timer’. 2 Set the TV channel and recording quality. • Use the CHANNEL /– buttons to set the channel you want to record. • Use the REC MODE ( SHIFT  ) button to set the recording quality. Press repeatedly to switch between XP , SP , LP , EP , SLP , SEP and AUTO (and MN if manual recording mode is on). • DVD recording: The AUTO option automatically sets the best recording quality for the space available on the disc loaded at the time of recording. • HDD recording: The AUTO option automatically sets the best recording quality that would fit on to a blank DVD disc. • Use the HDD/DVD button to select DVD or HDD to record to DVD or the HDD respectively. 3 Use /// to move the cursor to the recording start date and time on the grid. • You can move the cursor forward or back an hour at a time using the  and  buttons. Each row of the grid is one day (you can set the timer recording for up to a month in advance). Each column is a 15 minute interval. The darker area represents time that has already passed and can’t therefore be selected. The lighter area is time that’s available. 4 Press ENTER to set the start time. The start date and time is displayed in the middle of the screen. • You can go back and reset the start time if you need to by pressing RETURN . 5 Use the / to move the cursor to the recording end time on the grid. As you move the cursor around the grid, an arrow stretches from the start time to the current cursor position, representing the length of the recording. A recording of up to six hours can be set. STANDBY/ON TOP MENU MENU DISC NAVIGA TOR HOME MENU HDD/DVD TV/DVD DISPLAY RETURN AUDIO HELP CLEAR INPUT SELECT SUBTITLE ANGLE S HOW V IEW CHANNEL SKIP TV DRECT REC ENTER REC MODE ST0P REC REC SHIFT ONE TOUCH COPY BACK CM     T imer Recording Photo Viewer Disc Setup Play Mode Disc Navigator Initial Setup Video/Audio Adjust Copy Jukebox Easy Timer Recording Pr 7 SAT 1/01 9:30 HDD CHANNEL / – HDD/DVD SP REC MODE 8:00 9:00 10:00 11:00 12:00 13:00 14:00 – ––:–– 1/01 2/01 3/01 Easy Timer Recording Pr 7 SAT 1/01 11:45 HDD CHANNEL / – HDD/DVD SP REC MODE 8:00 9:00 10:00 11:00 12:00 13:00 14:00 – ––:–– 1/01 2/01 3/01 Current time Recording start time Easy Timer Recording Pr 7 SAT 1/01 11:45 HDD CHANNEL / – HDD/DVD SP REC MODE 11:00 12:00 13:00 14:00 15:00 16:00 17:00 – 13:45 1/01 2/01 3/01 Recording start time Recording end time DVR-433H_UK.book 42 ページ ２００５年３月１日　火曜日　午後５時６分
Recording 05 43 En 6 Press ENTER to set the end time. 7 Select ‘Yes’ to set the timer recording and exit, or ‘No’ to go back to the timer recording screen. Timer recording using the VIDEO Plus ® programming system This system makes programming timer recordings very simple. Most TV guides publish PlusCode programming numbers with their program details. If you want to make a timer recording of a program, you just input the corresponding code. The date, start, stop and channel settings are made automatically. All you have to do is tell the recorder the recording mode, and whether it’s a once-only recording or a regular recording. 1 Press ‘VIDEO Plus (SHIFT MENU )’ to display the VIDEO Plus program screen. You can also access this screen from the Home Menu (press HOME MENU , select Timer Recording , then VIDEO Plus ). • Use the number buttons to enter the PlusCode programming number. (To clear the last digit entered, press CLEAR .) • You can also use the /// buttons to select digits from the on-screen display. 2 After making the settings, select ‘Enter’ and press ENTER. The timer recording screen appears with the timer program you just set. 3 Confirm that the settings are correct. If the channel number isn't displayed, use the / buttons to highlight CH , then use the / buttons to set the correct channel number. • If the channel number is set, but incorrectly, set up the guide channel (see Set VIDEO Plus CH on page 93). 4 Select ‘Store Program’ to finish. • Other options in the same menu panel allow you to name the program, and change the recording destination and/or recording mode. DVD RECORDER STANDBY/ON TOP MENU MENU DISC NAVIGA TOR HOME MENU HDD/DVD TV/DVD DISPLAY RETURN AUDIO HELP CLEAR INPUT SELECT SUBTITLE ANGLE VIDEO Plus CHANNEL SKIP TV DRECT REC ENTER REC MODE ST0P REC REC SHIFT ONE TOUCH COPY BACK CM     PlusCode# 1 3 4 5 6 7 8 9 0 Clear Enter Cancel 2 DVR-433H_UK.book 43 ページ ２００５年３月１日　火曜日　午後５時６分
Recording 05 44 En VIDEO Plus programming with the power off You can enter a PlusCode programming number when the recorder is in standby. Note that the recording is always made to the HDD. If you want to record to a DVD disc, you’ll need to switch on the power and use the full VIDEO Plus program screen. Important • You can’t use this feature until you have set up the guide channels. See Set VIDEO Plus CH on page 93. • You can’t change the recording mode. • You can’t program daily or weekly timer recordings. 1 Press ’VIDEO Plus (SHIFT MENU )’. The front panel display shows the current recording mode and prompts you to enter the PlusCode programming number. 2 Use the number buttons to enter the number. • To clear the last digit entered, press CLEAR . 3 Press ENTER. The display shows the timer settings: Date  Start time  End time  HDD and Recording channel  Recording mode. • If CODE ERROR appears in the display, check that the number is correct and that the guide channel is set (see Set VIDEO Plus CH on page 93), then set the timer recording again. • If CAN’T SET appears in the display, it means that although you entered a valid number, the program has already finished. Setting a manual timer recording The timer recording screen you can see all the timer programs already set, clear programs and set up new ones. 1 Press TIMER REC to display the Timer Recording screen. You can also access the Timer Recording screen from the Home Menu (press HOME MENU , select Timer Recording , then Timer Recording ). This screen shows all the timer programs currently set. • Each row is for one timer recording program, with the date and time information, channel, recording mode, DVD or HDD and recording status. • The amount of free space available on the HDD and the currently loaded recordable DVD is shown towards the bottom of the screen. • In the upper-right corner, the number of timer programs already set is shown next to Tmr Pgms . • If there are more than five timer programs already set, press  to switch page (go back using the  button). • You can also delete a timer program before it’s started (before the recorder enters timer recording standby) by highlighting it and pressing CLEAR . See also Deleting a timer program on page 46. TOP MENU MENU DISC NAVIGA TOR HOME MENU TV/DVD DISPLAY RETURN AUDIO HELP CLEAR INPUT SELECT SUBTITLE ANGLE VIDEO Plus CHANNEL SKIP TV DRECT REC ENTER REC MODE ST0P REC REC SHIFT ONE TOUCH COPY BACK CM    TOP MENU MENU DISC NAVIGA TOR HOME MENU RETURN S HOW V IEW SKIP TV DRECT REC ENTER REC MODE ST0P REC REC SHIFT ONE TOUCH COPY BACK CM    HDD Remain DVD Remain 59h59m(SP) 1h59m(SP) SAT 26/3 15:00 Tmr Pgms 4/32 Manhattan Open T ennis OK SAT 26/3 18:00 – 21:00 Pr 10 Wo rld Journey OK SUN 27/3 19:30 – 21:00 Pr 4 Flower Until 30/4 MON – FRI 13:30 – 14:00 Pr 8 New Input T imer Program View DVR-433H_UK.book 44 ページ ２００５年３月１日　火曜日　午後５時６分
Recording 05 45 En 2 Select ‘New Input’ to set a new timer program, then press ENTER. 3 Enter the timer recording settings. Use the / buttons to select a field; use the / buttons to change the value. • CH – Choose a channel (Pr 1–Pr 99, excluding skip channels), or one of the external inputs from which to record. • Date – Choose a date up to one month in advance, or select a daily or weekly program. • Start – Set the recording start time. • Stop – Set the recording end time (maximum length of a timer recording is 24 hours). 4 If you want to change the recording mode, recording destination, etc., select ‘Set Detailed’. In this area you can set: Record to – Select HDD for hard disk recording or DVD for DVD recording. Select HDD for Auto Replace Recording (daily or weekly timer recording only). Recording Mode – Select XP , SP , LP , EP , SLP or SEP , (See Setting the picture quality/recording time on page 39). If Manual Recording is on, then you can also select the LPCM or XP setting, or MN (press ENTER then use the / buttons to select the level). Replace – Auto Replace Recording: automatically erases the previous daily or weekly recording when the next one is recorded. Genre – Select a record genre (for HDD recording only). Bilingual – Select which channel of a bilingual broadcast to record (necessary if recording to a Video mode DVD or to the HDD with the HDD Rec Mode set to Video Mode On ). HDD Recording Format – Select Video Mode On or Video Mode Off depending on whether you need high- speed copying to Video mode DVD capabillity or not. 5 After entering all the timer recording information, highlight ‘Store Program’ and press ENTER. The timer recording list screen is displayed again. The timer program you just input appears in the list. The rightmost column shows various timer recording status messages: • OK – Can be recorded. • Time Over – Not enough space on the HDD (the recording won’t finish). • Over 12h – Recording time of over 12 hours set (when recording to the HDD the recording will be split into two titles). • Overlap – Two timer programs partially or completely overlap. The one starting earlier will take priority. • Until ... (eg., Until 13/8 ) – For a regular recording, the last program that could be recorded is shown. • Data Over –Can’t record because the disc management area of the disc is full. • Cancel Once – A regular timer program is set to skip. • Can’t Rec – Not possible to record for some reason. • Title Over – Can’t record because there is already the maximum number of titles on the disc (HDD: 999; DVD: 99). • Recording – The program is currently recording. • Standby – The recorder is in timer recording standby. • nothing displayed – Another timer recording or copying is in progress. 6 To exit the timer recording screen, press HOME MENU. Tip • To enter a title name for the timer recording in advance, select Set Title Name and follow the on- screen display. Note • If you set a DVD timer recording but there is no recordable DVD disc loaded, or the disc loaded doesn’t have enough free space for the complete recording, Recovery is shown. In this case (unless you load a suitable disc before the recording actually starts), the recorder will use the HDD for recording. (The message Can’t Rec will appear if there are already 999 titles on the HDD or if there is not enough free space on the HDD for recording.) • For a DVD timer recording, if Optimized Rec (see Optimized Rec on page 97) is set to On , the recorder will adjust the recording quality to try and fit the recording on the disc. If the recording will not fit onto the disc even on MN1 recording quality then the Recovery Recording feature will automatically make the recording to the HDD instead. • If there is very little free space left on the HDD, an Auto Replace Recording may not complete successfully. T imer Program Set Manhattan Open T ennis CH Date Start Stop Extend Pr 10 SA T 26/3 18:00 21:00 30 min Enter Details Detailed Settings Record T o HDD Recording Mode XP Auto Replace Rec. On Genre No Category Bilingual Recording A/L HDD Recording Format Video Mode On Store Program Cancel Set Title Name Set Detailed DVR-433H_UK.book 45 ページ ２００５年３月１日　火曜日　午後５時６分
Recording 05 46 En • If the HDD is being used for playback or high-speed copying when an Auto Replace Recording is due to start, the new timer recording will not replace the old one. However, the next time the timer recording starts, both of the older two programs will be erased. Editing a timer program You can change any of the settings in a timer program before the recording is due to start. 1 Press TIMER REC. 2 Highlight the timer program you want to change . . . . 3 Press  then select ‘Modify’ from the command menu panel. Alternatively, press ENTER . The Timer Program Set screen appears from which you can edit the settings. 4 Edit the timer recording settings as necessary. 5 Select ‘Store Program’ to finish. Confirm the settings you made from the following screen. Deleting a timer program You can delete timer programs you no longer need. 1 Press TIMER REC. 2 Highlight the timer program you want to erase . . . . 3 Press  then select ‘Erase’ from the command menu panel. • Select Yes to confirm or No to cancel. • You can also just press CLEAR when the timer program is highlighted. Skipping a regular timer program If you’ve set a regular daily or weekly timer program, you can set the recorder to skip the next scheduled recording. 1 Press TIMER REC. 2 Highlight the timer program you want to skip . . . . 3 Press  then select ‘Cancel Once’ from the command menu panel. You can also just press  when the timer program is highlighted. • In the timer program list, Cancel Once appears by the program. Extending a timer recording in progress You can extend a timer recording beyond the programmed end time in two different ways. This can be useful if a broadcast program overruns, for example. Moving the end time by 30-minute blocks 1 During timer recording, press and hold  REC for three seconds. The timer indicator disappears from the front panel display. 2 Press  REC repeatedly to extend recording in 30 minute increments. Programming a new end time You can edit the end time of a timer recording you have previously set. 1 Press TIMER REC. 2 Highlight the timer program you want to change. 3 Press  then select ‘Modify’ from the command menu panel. Alternatively, press ENTER . The Timer Program Set screen appears from which you can edit the settings. 4 Edit the end time as necessary. • You can also edit the Extend time parameter. 5 Select ‘Store Program’ then press ENTER. 6 To exit the timer recording screen, press HOME MENU. TOP MENU MENU DISC NAVIGA TOR HOME MENU RETURN S HOW V IEW SKIP TV DRECT REC ENTER REC MODE ST0P REC REC SHIFT ONE TOUCH COPY BACK CM    DVR-433H_UK.book 46 ページ ２００５年３月１日　火曜日　午後５時６分
Recording 05 47 En Canceling and stopping a timer recording in progress After a timer recording has started, you can cancel the program (but continue recording), or stop recording completely if you need to. 1 During timer recording, press and hold  REC for three seconds. Only the program is canceled (the timer indicator disappears); recording continues so that you can manually stop recording whenever you like. 2 When you want to stop recording completely, press  STOP REC. Tip • You can also stop a timer recording immediately by pressing  STOP REC then selecting Yes to confirm. Preventing use of the recorder before a timer recording (child lock) You can make all the front panel and remote control buttons inoperative using the child lock feature. This is useful when you set a timer recording and want to make sure that the timer settings are not changed before recording has finished. 1 If the recorder is on, switch it into standby. 2 Press and hold  on the front panel for three seconds to lock the controls. The front panel display briefly shows LOCK . If any buttons are pressed on the remote or front panel, LOCK is briefly displayed again. • To unlock the recorder, press and hold  on the front panel for three seconds until the display shows UNLOCK . • To cancel a timer recording when the recorder is locked, first unlock the recorder (see above), then press and hold  REC for three seconds. Timer recording FAQ Frequently Asked Questions • Even though the timer is set, the recorder doesn’t start recording! Check that the disc loaded or HDD is recordable, not locked (see Lock Disc on page 87), and that there are fewer than 99/999 titles already on the DVD/HDD. • The recorder won’t let me enter a timer program! Why not? You can’t enter a timer program if the clock isn’t set. • What happens when two or more timer programs overlap? Basically, the program with the earlier recording start time has priority. However, the recorder will start recording the program with the later start time after the earlier program is finished. If two programs have the same times, only one of them will be recorded, so it is best to set one of them to Cancel Once . See Skipping a regular timer program on page 46. DVD RECORDER SKIP TV DRECT REC REC MODE ST0P REC REC SHIFT ONE TOUCH COPY BACK CM  DVR-433H_UK.book 47 ページ ２００５年３月１日　火曜日　午後５時６分
Recording 05 48 En Simultaneous recording and playback A feature called Chase Play makes it possible to watch a recording in progress (DVD or HDD) from the start of the recording (as in, playback is ‘chasing’ the recording). For example, perhaps you have to miss the first 30 minutes of a movie on TV; you can start recording, then start watching the movie, from the beginning, while the recorder is still recording 30 minutes ahead of you. In fact, you’re not just limited to watching the recording in progress; you can watch anything else already on the DVD or HDD by selecting it from the Disc Navigator screen (see Using the Disc Navigator with recordable discs and the HDD on page 54). Important • Note that you must use a DVD-RW Ver. 1.1 / 2x or Ver. 1.2 disc to be able to use this feature. • You may not be able to use this feature with a DVD-RW disc that was first initialized on another recorder. • Chase playback is not possible using a VR mode DVD-R disc. • During recording, press  to start playback from the beginning of the current recording 1 , or press DISC NAVIGATOR and select another title to play from there. You can use all the usual playback controls, such as pause, slow-motion play, scan 2 and skip. • To stop playback, press  (recording will continue). • To stop recording, press  STOP REC (playback will continue). • During recording or in timer recording standby, you can’t play an HDD title, DVD or Video CD/Super VCD disc if the Input Line System setting doesn’t match the TV line system of the disc/HDD title (see also Additional information about the TV system settings on page 99). Also, during simultaneous recording and playback, if the TV line system of the playback track/title changes then playback will automatically stop. Recording from an external component You can record from an external component, such as a camcorder or VCR, connected to one of the recorder’s external inputs. 1 Make sure that the component you want to record from is connected properly to the DVD recorder. See Chapter 2 ( Connecting up ) for connection options. 2 Press INPUT SELECT repeatedly to select one of the external inputs to record from. There are three analog inputs and a DV digital input. The current input is shown on-screen and in the front panel display: • AV2/L1 – Input 1 3 • L2 – Input 2 (front panel) • L3 – Input 3 • DV – DV input (front panel) Note 1. You can’t start playback immediately after recording starts. Simultaneous playback and recording doesn’t work while copying or backing up. 2. When scanning a DVD, no sound is output if the recorder is also recording the DVD (see Scanning discs on page 56). VR mode HDD 3. This cannot be selected if AV2/L1 In is set to Decoder (see AV2/L1 In on page 94). VR mode Video mode HDD DVD RECORDER STANDBY/ON TOP MENU MENU DISC NAVIGA TOR HOME MENU HDD/DVD TV/DVD DISPLAY RETURN AUDIO HELP CLEAR INPUT SELECT SUBTITLE ANGLE S HOW V IEW CHANNEL SKIP TV DRECT REC ENTER REC MODE ST0P REC REC SHIFT ONE TOUCH COPY BACK CM     DVR-433H_UK.book 48 ページ ２００５年３月１日　火曜日　午後５時６分
Recording 05 49 En Check that the Audio In settings for External Audio , Bilingual Recording and DV Input are as you want them (see Audio In Settings on page 94). • If the aspect ratio is distorted (squashed or stretched), adjust on the source component or your TV before recording. 3 Set up the recorder. • Use REC MODE ( SHIFT  ) to set the recording quality. See Setting the picture quality/recording time on page 39 for detailed information. • Use the HDD/DVD button to select the HDD or DVD for recording. 4 Press  REC when you’re ready to start recording. • The recorder will only start recording from the DV IN jack if there is a valid signal. Recording will also pause if the signal is interrupted during recording. • If your source is copy-protected using CopyGuard, you will not be able to record it. See Restrictions on video recording on page 38 for more details. Automatic recording from a satellite tuner If you have a satellite tuner or some other kind of set top box connected to the AV2/AUTO START REC (INPUT 1/ DECODER) input, you can have the recorder start and stop recording automatically with the timer settings of the connected component. (If the other component doesn’t have a built-in timer, you’ll need to use it with an external timer unit.) 1 After setting up for Auto Start Recording, this recorder starts recording when it detects a signal from the other component. When the signal ceases, the recorder stops recording. If you want to use this recorder with the timer features of your satellite tuner, see Language code list on page 108. Important • It takes a little while for this recorder to switch on and start recording after detecting a signal. Please bear this in mind when setting the timer. • If Auto Start Recording is set, it will not start if another timer recording is in progress. • Timer recordings take precedence over Auto Start Recording. Auto Start Recording will stop if a timer recording is due to start. After the timer recording has finished, Auto Start Recording will resume. 1 Set the timer for the satellite receiver (or other component), then switch it into standby (if necessary). Check the manual that came with the receiver if you’re not sure how to do this. 2 Check that the ‘Audio In’ settings for ‘External Audio’ and ‘Bilingual Recording’ are as you want them. See Audio In Settings on page 94 for more on these settings. 3 Set up the recorder. • Use REC MODE ( SHIFT  ) to set the recording quality. See Setting the picture quality/recording time on page 39 for detailed information. 4 Press HOME MENU and select ‘Timer Recording’, then ‘Auto Start Recording’. 5 Select ‘Yes’ to switch Auto Start Recording on, or ‘No’ to switch off. 6 Switch the recorder into standby. The AUTO indicator in the front panel display lights. The recorder will automatically switch on and start recording when the other component comes on. Recording stops when the external component switches off. • To cancel Auto Start Recording, press  STANDBY/ ON while the recorder is in standby. The AUTO indicator goes off. • To cancel Auto Start Recording once recording has already started, press  REC for three seconds (this cancels Auto Start Recording, but recording continues), then  STOP REC to stop recording. • You can also stop recording by pressing  STOP REC then selecting Yes to confirm. Tip • Alternatively, with no OSD displayed, press and hold the front panel  STOP REC button for more than three seconds to switch Auto Start Recording on directly. After switching on, switch the recorder into standby (step 6 ). Note 1. You can’t set Auto Start Recording when: – the recorder is recording or in timer recording standby. – the HDD is not recordable. – the HDD already contains the maximum number of titles (999). HDD DVR-433H_UK.book 49 ページ ２００５年３月１日　火曜日　午後５時６分
Recording 05 50 En Recording from a DV camcorder You can record from a DV camcorder connected to the DV IN jack on the front panel of this recorder. Using the recorder’s remote, you can control both the camcorder and this recorder. Before recording, make sure that the audio input for the DV IN jack is setup (see DV Input on page 95). Important • The source signal must be DVC-SD format • Some camcorders cannot be controlled using this recorder’s remote. • If you connect a second recorder using a DV cable, you cannot control the second unit from this one. • You can’t control this unit remotely from a component connected to the DV IN jack. • You can’t record date and time information from DV cassette. • During DV recording, if a part of the tape is blank, or has copy-protected material on it, this recorder will pause recording. Recording will restart automatically when there is a recordable signal. However, if there is more than 10 seconds of blank tape, this recorder will stop recording and the camcorder should stop (depending on the camcorder). • For best results when recording from a DV camcorder to this recorder, we recommend cueing the camcorder to the place you want to start recording from and setting the camcorder to play- pause. 1 Make sure your digital camcorder is connected to the front panel DV IN jack. Also, set the camcorder to VTR mode. 2 Set up the recorder. • Use REC MODE ( SHIFT  ) to set the recording quality. See Setting the picture quality/recording time on page 39 for detailed information. • Make sure a recordable disc is loaded if you want to record to DVD. 3 From the Initial Settings menu, check that the DV audio input is setup as you require. See DV Input on page 95 for more on this. • Check also that the Audio In settings for External Audio and Bilingual Recording are as you want them (see Audio In Settings on page 94). 4 Press HOME MENU, select ‘Copy’, then ‘DV Record’ from the menu. • DV recording only works when the digital camcorder is in VTR mode with a tape loaded. 5 Select ‘Record to Hard Disk Drive’ or ‘Record to DVD’ to record to the hard disk drive or a recordable DVD respectively. 6 Find the place on the camcorder tape that you want to start recording from. For best results, pause playback at the point from which you want to record. VR mode Video mode HDD DVD RECORDER STANDBY/ON TOP MENU MENU DISC NAVIGA TOR HOME MENU HDD/DVD TV/DVD DISPLAY RETURN AUDIO HELP CLEAR INPUT SELECT SUBTITLE ANGLE S HOW V IEW CHANNEL SKIP TV DRECT REC ENTER REC MODE ST0P REC REC SHIFT ONE TOUCH COPY BACK CM     DVR-433H_UK.book 50 ページ ２００５年３月１日　火曜日　午後５時６分
Recording 05 51 En • Depending on your camcorder, you can use this recorder’s remote to control the camcorder using the  ,  ,  ,  ,  , / and / buttons. 7 Use the / buttons to select ‘Start Rec’ and press ENTER. • Recording is automatically paused if the recorder detects no signal, or a copy-protected signal. Recording restarts when there is a non-copy- protected signal. • You can pause or stop the recording by selecting Pause Rec or Stop Rec from the on-screen display. You cannot control the camcorder from this remote control during recording. • If you restart recording after stopping the camcorder, the first few seconds of the camcorder tape will not be recorded. Use the pause button on your camcorder instead and recording will start immediately. • HDD and DVD-RW (VR Mode) only: A chapter marker is inserted every time there is a break in the timecode on the DV tape. This happens when the recording is stopped or paused then restarted, for example. • While recording, you cannot exit the DV recording screen using the HOME MENU or RETURN button. • See also DV-related messages on page 106 if you encounter an error while using the DV IN jack. Frequently Asked Questions •I can’t get my DV camcorder to work with the recorder! Check that the DV cable is properly connected. Also make sure that what you’re trying to record is not copy-protected. If it still doesn’t work, try switching off the camcorder then switch back on. • There’s a picture, but no sound! Try switching the DV Input setting (see DV Input on page 95) between Stereo 1 and Stereo 2 . 1 Playing your recordings on other DVD players Most regular DVD players can play finalized discs recorded in Video mode. A number of players (including many Pioneer models) can also play DVD-RW discs recorded in VR mode, finalized or not. Most players will not play VR mode DVD-R discs, although some DVD- ROM drives and DVD recorders may be able to (finalization might be necessary). Check the manual that came with the player to check what kinds of discs it will play. When you finalize a Video mode disc, a title menu is created from which you can select titles when you play the disc. There are a number of different styles of title menu to choose from to suit the content of the disc. All the title menus are navigated in the usual way, pressing MENU or TOP MENU to display the menu, then using the /// followed by ENTER to select titles and start playback. Finalizing a disc Finalizing ‘fixes’ the recordings in place so that the disc can be played on a regular DVD player or computer equipped with a suitable DVD-ROM drive. 2 Note that the disc name will appear in the title menu after you finalize a disc. Make sure the disc name is as you want it before you finalize the disc as it can’t be changed afterwards. If you want to rename the disc, see Input Disc Name on page 87 before starting the steps below. Important • Once you’ve finalized a disc recorded in Video mode, you can’t edit or record anything else on that disc. However, the finalization on a DVD-RW disc maybe ‘undone’; see Undo Finalize on page 88 for how to do this. •A VR mode disc can still be recorded and edited on this recorder even after finalizing. 1 Load the disc you want to finalize. Make sure that the recorder is stopped before proceeding. Note 1. If the audio subcode on the DV tape cannot be read correctly, the audio type will not switch automatically. You can switch the audio manually from the External Audio setting (page 94). Start Rec Pause Rec Stop Rec SP (2h00m/DVD) 32h45m  Stop  Stop 1.02.22 Control with these buttons       Rem. HDD 2. If the TV line system of the disc is different to the current setting of the recorder, you will not be able to finalize the disc. See Additional infor- mation about the TV system settings on page 99 for how to change the recorder’s setting. VR mode Video mode VR mode Video mode DVR-433H_UK.book 51 ページ ２００５年３月１日　火曜日　午後５時６分
Recording 05 52 En 2 Press HOME MENU and select ‘Disc Setup’. 3 Select ‘Finalize’. 4 Select ‘Finalize’ from the finalize options, then ‘Next Screen’. 5 For Video mode discs only, select a title menu style, then select ‘Yes’ to start finalization or ‘No’ to cancel. The menu you select will be the one that appears when the ‘top menu’ is selected on any DVD player. • Discs recorded partially or fully on the Pioneer DVR-7000 DVD recorder do not support this feature. These discs will have only a text title menu when finalized on this recorder. 6 The recorder will now start finalizing the disc. During finalization: • If the finalization process of a DVD-RW disc is going to take more than around four minutes, you can press ENTER to cancel. Around four minutes before completion, the option to cancel disappears. • You can’t cancel the finalization of a VR mode DVD-R disc. • How long finalization takes depends on the type of disc, how much is recorded on the disc and the number of titles on the disc. A disc recorded in VR mode can take up to one hour to finalize. A disc recorded in Video mode can take up to 20 minutes. Initializing a recordable DVD disc When you first load a blank disc, the recorder will initialize it automatically for recording. You can also manually initialize discs for either Video mode recording or VR mode recording. 1 By default, the recorder initializes blank DVD-RW discs for VR mode recording. See DVD-RW Auto Init. on page 97 if you want to change the default to Video mode. DVD-R discs are ready for Video mode recordings out of the box; if you want to use a DVD-R for VR mode recording, you must do it before recording anything else on the disc. Important • Initializing a DVD-RW disc will erase everything recorded on it. Make sure there is nothing on the disc that you want to keep! • You may not be able to re-initialize a DVD-RW disc in a different format if it was originally initialized on an older DVD recorder. • Once initialized for VR mode recording, you can’t re- initialize a DVD-R back to Video mode. 1 Press HOME MENU and select ‘Disc Setup’. 2 Select ‘Initialize’ 3 Select ‘Video Mode’ or ‘VR Mode’ from the initialize options. 4 Select ‘Start’. It takes about 30 seconds to initialize the disc. Basic Initialize Finalize Optimize HDD Disc Setup Finalize Undo Finalize Next Screen Start Finalize T I T L E M E N U TITLE MENU Finalize Note 1. If a disc was previously finalized on an older DVD recorder, you may not be able to re-initialize and/or initialize it for Video mode recording. Basic Initialize Finalize Optimize HDD Disc Setup VR Mode Video Mode Start Start Initialize Initializing Disc 1 min left Pr 1 DVR-433H_UK.book 52 ページ ２００５年３月１日　火曜日　午後５時６分
Playback 06 53 En Chapter 6 Playback Introduction Most of the features described in this chapter make use of on-screen displays. Navigate these using the ///  and ENTER . To go back one level from any screen, use the RETURN button. Remember also that the button guide at the bottom of every screen shows which buttons do what. Many of the functions covered in this chapter apply to the HDD, DVD discs, Video CDs, Super VCDs, WMA/MP3 discs and CDs, although the exact operation of some varies slightly with the kind of disc loaded. The following icons are provided to help you quickly identify which instructions you need for which kind of disc. Any kind of DVD, DVD-R or DVD-RW Commercially produced DVD or finalized Video mode DVD-R/RW Video mode DVD-R/RW (unfinalized) VR mode DVD-R/RW HDD Audio CD Video CD Super VCD WMA or MP3 files • Some DVD-Video discs don’t allow certain playback controls to operate at certain points in the disc. This is not a malfunction. • When playing Video CDs, some functions, such as making a program list, are not available in PBC mode. Stop the disc first, then start playback by pressing  . • For discs that contain JPEG picture files, see The PhotoViewer on page 85. Navigating discs and the HDD During playback you can easily jump to another title, chapter or track on a disc using the number buttons on the remote. 1 During playback use the number buttons to enter a chapter number within the current title. For example, for chapter 6, press 6 ; for chapter 24, press 2 , then 4 . • To clear and start again, press CLEAR . 2 Optionally: Press ENTER. • Alternatively, just wait a few seconds and playback will jump to the new chapter. 1 During playback, use the number buttons to input a title number. For example, for title 6, press 6 ; for title 24, press 2 , then 4 . • To clear and start again, press CLEAR . 2 Optionally: Press ENTER. • Alternatively, just wait a few seconds and playback will jump to the new title. DVD DVD-Video Video mode VR mode HDD CD Video CD S uper VCD MP3 ALL TOP MENU MENU DISC NAVIGA TOR HOME MENU TV/DVD DISPLAY RETURN AUDIO HELP CLEAR INPUT SELECT SUBTITLE ANGLE S HOW V IEW CHANNEL ENTER   DVD-Video Video mode HDD VR mode DVR-433H_UK.book 53 ページ ２００５年３月１日　火曜日　午後５時６分
Playback 06 54 En 1 During playback, use the number buttons to input a track number. For example, for track 6, press 6 ; for track 24, press 2 , then 4 . • To clear and start again, press CLEAR . 2 Optionally: Press ENTER. • Alternatively, just wait a few seconds and playback will jump to the new track. Using the Disc Navigator to browse the contents of a disc. Use the Disc Navigator to browse the contents of a disc and start playback. Using the Disc Navigator with recordable discs and the HDD You can use the Disc Navigator to browse and edit video on recordable DVDs and the HDD, and to view information on titles. See also Editing on page 73 for more on editing recordable discs. 1 Use the HDD/DVD button to select the hard disk drive or DVD. 2 Press HOME MENU and select ‘Disc Navigator’ from the on-screen display. Alternatively, you can press DISC NAVIGATOR to go straight to the Disc Navigator screen. 3 Use the / buttons to browse up and down the list of titles. • Use the / buttons to display the previous/ next page of titles, if there are more titles than can fit on to the screen. • You can change the style and order in which titles are displayed from the view options menu. See below for more on this. • You can change the thumbnail picture displayed for a title; see Set Thumbnail on page 76. 4 To play the highlighted title, press ENTER. • You can also select Play from the command menu options. Tip • Use the time search feature to find a particular point on a DVD or within a title on the HDD. See Search Mode on page 57 for more information. Changing the display style of the Disc Navigator You can choose to display titles in the Disc Navigator in various different ways, sorted alphabetically, by recording date, by genre, and so on. You can also choose whether to display four or eight titles on the screen at the same time. 1 From the Disc Navigator’s title list, press  to display the view options panel. 2 Use the / buttons to select ‘Style’, ‘Sort Order’ or ‘Genre’, then press ENTER to see the available view options. • Style – Select four or eight titles per screen view CD Video CD S uper VCD MP3 VR mode Video mode HDD Disc Navigator (HDD) 11/29 MON 7:00PM 11/29Mon 7:00PM 2ch SP 2h00m(1.0G) 1 4 Titles Remain HDD SP Recent First All Genres 10Titles 30h30m 20:00 FRI 3/12 20:00 Fri 3/12 Pr 9 SP 2h00m(1.0G) 22:00 THU 2/12 22:00 Thu 2/12 Pr 7 SP 1h00m(1.0G) 19:00 MON 29/11 19:00 Mon 29/11 Pr 2 SP 1h00m(1.0G) 23:00 FRI 3/12 23:00 Fri 3/12 Pr 4 SP 2h00m(1.0G) 9 8 7 10 Disc Navigator (HDD) 11/29 MON 7:00PM 11/29Mon 7:00PM 2ch SP 2h00m(1.0G) 1 2 3 7 4 Titles Remain HDD SP NEW first All Genres 10Titles 30h30m 1 20:00 FRI 3/12 20:00 Fri 3/12 Pr 9 SP 2h00m(1.0G) 22:00 THU 2/12 22:00 Thu 2/12 Pr 7 SP 1h00m(1.0G) 19:00 MON 29/11 19:00 Mon 29/11 Pr 2 SP 1h00m(1.0G) 23:00 FRI 3/12 23:00 Fri 3/12 Pr 4 SP 2h00m(1.0G) 4 Titles Sort order Recent First Genre All Genres Style The View Options panel Disc Navigator (HDD) 11/29 MON 7:00PM 11/29Mon 7:00PM 2ch SP 2h00m(1.0G) 1 2 3 7 4 Titles Remain HDD SP NEW first All Genres 10Titles 30h30m 1 20:00 FRI 3/12 20:00 Fri 3/12 Pr 9 SP 2h00m(1.0G) 22:00 THU 2/12 22:00 Thu 2/12 Pr 7 SP 1h00m(1.0G) 19:00 MON 29/11 19:00 Mon 29/11 Pr 2 SP 1h00m(1.0G) 23:00 FRI 3/12 23:00 Fri 3/12 Pr 4 SP 2h00m(1.0G) 4 Titles Sort order Recent First Genre All Genres Style 4 Titles Cancel 8 Titles DVR-433H_UK.book 54 ページ ２００５年３月１日　火曜日　午後５時６分
Playback 06 55 En • Sort Order – Sort by date (most recent first), unwatched first, title name or recording date (oldest first) • Genre – Display all genres or just a selected genre 3 Use the / buttons to select an option, then press ENTER. The title list display is updated according to the new display preferences. 4 Press  to return to the title list. Using the Disc Navigator with playback-only discs 1 Press HOME MENU and select ‘Disc Navigator’ from the on-screen display. Alternatively, for a CD, Video CD, Super VCD or WMA/ MP3 disc, you can press DISC NAVIGATOR , which takes you straight to the Disc Navigator screen. 2 Select what you want to play. Use the /// to highlight items and ENTER to select. Depending on the type of disc you have loaded, the Disc Navigator looks slightly different. • When a DVD is loaded, titles are shown on the left, chapters on the right. Select a title, or a chapter within a title. • When a CD or Video CD /Super VCD 1 is loaded, a list of the tracks is displayed. • When a WMA/MP3 disc is loaded, a list of folders and tracks is displayed (as shown below). Select a folder or a track within a folder. Playback starts after you press ENTER . • For discs that contain both CD-Audio tracks and WMA/MP3 tracks, you can switch the playback area between CD and WMA/MP3 . This can only be done while the disc is stopped. Disc Navigator (HDD) 11/29 MON 7:00PM 11/29Mon 7:00PM 2ch SP 2h00m(1.0G) 1 2 3 7 4 Titles Remain HDD SP NEW first All Genres 10Titles 30h30m 1 20:00 FRI 3/12 20:00 Fri 3/12 Pr 9 SP 2h00m(1.0G) 22:00 THU 2/12 22:00 Thu 2/12 Pr 7 SP 1h00m(1.0G) 19:00 MON 29/11 19:00 Mon 29/11 Pr 2 SP 1h00m(1.0G) 23:00 FRI 3/12 23:00 Fri 3/12 Pr 4 SP 2h00m(1.0G) 4 Titles Sort order Recent First Genre All Genres Style Recent first By rec.date New first Cancel By title Disc Navigator (HDD) 11/29 MON 7:00PM 11/29Mon 7:00PM 2ch SP 2h00m(1.0G) 1 2 3 7 4 Titles Remain HDD SP NEW first All Genres 10Titles 30h30m 1 20:00 FRI 3/12 20:00 Fri 3/12 Pr 9 SP 2h00m(1.0G) 22:00 THU 2/12 22:00 Thu 2/12 Pr 7 SP 1h00m(1.0G) 19:00 MON 29/11 19:00 Mon 29/11 Pr 2 SP 1h00m(1.0G) 23:00 FRI 3/12 23:00 Fri 3/12 Pr 4 SP 2h00m(1.0G) 4 Titles Sort order Recent First Genre All Genres Style All Genres Free 5 Free 3 Free 1 Free 4 No Category Free 2 STANDBY/ON TOP MENU MENU DISC NAVIGA TOR HOME MENU HDD/DVD TV/DVD DISPLAY RETURN AUDIO HELP CLEAR INPUT SELECT SUBTITLE ANGLE S HOW V IEW CHANNEL ENTER    Note 1. It’s not possible to use the Disc Navigator when playing a Video CD/Super VCD in PBC mode. DVD-Video CD Video CD S uper VCD MP3 T imer Recording Photo Viewer Disc Setup Play Mode Disc Navigator Initial Setup Video/Audio Adjust Copy Jukebox CD WMA/MP3 Folder (01-03) 01.Rock 02.Pop 03.Dance Tr ack(001-004) 001.Intro 002.Escape 003.Everything You Say 004.What I Do Disc Navigator DVR-433H_UK.book 55 ページ ２００５年３月１日　火曜日　午後５時６分
Playback 06 56 En Scanning discs You can fast scan discs at various speeds, forwards or backward. 1 1 During playback, press  or  to start reverse or forward scanning. • The scanning speed is shown on-screen. 2 Press the same button repeatedly to increase the scanning speed. • Forward: SCAN 1 (1.5x Quick View)  SCAN 2  SCAN 3  SCAN 4 • Reverse: Reverse play 2  SCAN 1  SCAN 2  SCAN 3  SCAN 4 • Forward/Reverse: SCAN 1  SCAN 2 3 To resume normal playback, press  . Playing in slow motion You can play video at various slow motion speeds. DVDs and video on the HDD can be played in slow motion in either direction, while Video CD/Super VCDs can only be played forwards in slow motion. 3 1 During playback, press  . 2 Press and hold / or / to start slow motion reverse or forward playback. 3 Press the same button repeatedly to change the slow motion speed. 4 To resume normal playback, press  . Note 1. • Only analog audio is output when scanning audio CDs. • No subtitles are displayed when scanning DVDs. • Analog and digital sound is output when scanning DVDs with Dolby Digital or Linear PCM sound on forward SCAN 1 . (Linear PCM is output from the optical digital output, Except during chase playback and simultaneous recording/playback) No sound is output when using other scan speeds. • No sound is output when scanning from the HDD, except on forward SCAN 1 . (Linear PCM is output from the optical digital output during forward SCAN 1 ). • Depending on the disc, normal playback may automatically resume when a new chapter is reached on a DVD disc. 2. Depending on the disc, reverse playback may not be smooth. MENU RETURN SKIP REC MODE ONE TOUCH BACK CM   DVD HDD CD Video CD S uper VCD MP3 3. • The picture quality during slow motion playback is not as good as during normal playback and depends on the disc being played. • Reverse slow-motion playback may not be as smooth as forward and may be better with some discs than others. • Depending on the disc, normal playback may automatically resume when a new chapter is reached on a DVD disc. • No sound is output during slow-motion playback. DVD HDD Video CD S uper VCD SKIP REC MODE ST0P REC REC SHIFT ONE TOUCH COPY BACK CM    SL OW 1/16 SL OW 1/8 SL OW 1/2 SL OW 1/4 DVR-433H_UK.book 56 ページ ２００５年３月１日　火曜日　午後５時６分
Playback 06 57 En Frame advance/frame reverse You can advance or back up video on a DVD disc or the HDD frame-by-frame. With Video CD/Super VCDs, you can only use frame advance. 1 1 During playback, press  . 2 Press / or / to back up or advance one frame. 3 To resume normal playback, press  . The Play Mode menu The Play Mode menu gives you access to search functions, repeat and program play functions. Important • You can’t use the Play Mode features with Video CD / Super VCDs playing in PBC mode, or while a DVD disc menu is being displayed. For other restrictions, see the following sections. 1 Press HOME MENU and select ‘Play Mode’ to display the Play Mode menu screen. 2 Use the /// and ENTER to navigate. • To exit the Play Mode menu, press HOME MENU . Search Mode The Search Mode feature lets you start playback from a specified point in a disc by time 2 or by title/chapter/ folder/track number. 1 Select ‘Search Mode’ from the Play Mode menu. 2 Select one of the search options. 3 Use the number buttons to enter a title/chapter/ folder/track number or the search time (in hours, minutes & seconds). Time Search (HDD, DVD): For example, for 25 minutes into the current title, press 2, 5, 0, 0 . For 1 hour and 15 minutes and 20 seconds into the title, press 1 , 1 , 5 , 2 , 0 . Time Search (Video CD): For example, for 2 minutes and 30 seconds into the current track, press 2 , 3 , 0 . Title/Chapter/Folder/Track Search: For example, for track 6, press 6 . Alternatively, you can use the / buttons. 4 Press ENTER. Tip • You can often select what you want to watch on a DVD disc from the disc menu. Press MENU or TOP MENU to display the disc menu. • Time search doesn’t work with CDs and Super VCDs. Note 1. • The picture quality when using frame reverse is not as good as frame advance. • Depending on the disc, normal playback may automatically resume when a new chapter is reached on a DVD disc. DVD HDD Video CD S uper VCD MENU RETURN SKIP TV DRECT REC REC MODE ST0P REC REC SHIFT ONE TOUCH COPY BACK CM    ALL TOP MENU MENU DISC NAVIGA TOR HOME MENU TV/DVD DISPLAY RETURN AUDIO HELP CLEAR INPUT SELECT SUBTITLE ANGLE S HOW V IEW CHANNEL SKIP ENTER REC MODE BACK CM   2. When using time search, playback may occasionally start slightly before or after the time you input. T ime Search T itle Search Chapter Search Play Mode Search Mode A-B Repeat Repeat Program ALL T ime Search T itle Search Chapter Search Play Mode Search Mode A-B Repeat Repeat Program Input Time 0.00.00 DVR-433H_UK.book 57 ページ ２００５年３月１日　火曜日　午後５時６分
Playback 06 58 En A-B Repeat The A-B Repeat function allows you to specify two points (A and B) within a track or title that form a loop which is played over and over. 1 1 During playback, select ‘A-B Repeat’ from the Play Mode menu. 2 With ‘A (Loop Start)’ highlighted, press ENTER at the point you want the loop to start. After setting the loop start point, the highlight will automatically move down to B (Loop End) . 3 With ‘B (Loop End)’ highlighted, press ENTER at the point you want the loop to end. Playback immediately jumps back to the start point and plays the loop round and round. • When playing a DVD-Video/Video mode DVD, or from the HDD, the start and end points of the loop must be in the same title. 4 To resume normal playback, select ‘Off’ from the A-B Repeat menu. • You can also press CLEAR to cancel A-B Repeat play if no menu OSD (such as the Play Mode menu) is displayed. Repeat play There are various repeat play options, depending on the kind of disc loaded, or if you’re using the HDD for playback. It’s also possible to use repeat play together with program play to repeat the tracks/chapters in the program list (see Program play on page 59). 2 1 Select ‘Repeat’ from the Play Mode menu. 2 Select a repeat play mode. • For VR mode DVD discs, select Repeat Disc , Repeat Title or Repeat Chapter (or Repeat Off ). • For HDD, DVD-Video and Video mode DVD discs, select Repeat Title or Repeat Chapter (or Repeat Off ). • For CDs and Video CD /Super VCDs, select Repeat Disc or Repeat Track (or Repeat Off ). • For WMA/MP3 discs, select Repeat Disc , Repeat Folder or Repeat Track (or Repeat Off ). 3 To resume normal playback, select ‘Repeat Off’ from the Repeat Play menu. • You can also press CLEAR to cancel repeat play if no menu OSD (such as the Play Mode menu) is displayed. Note 1. • If you switch camera angles during A-B repeat play, A-B repeat is canceled. • You can’t use A-B Repeat with WMA/MP3 or Super VCD discs. 2. If you switch the camera angle during repeat play of a DVD-Video disc, repeat play is canceled. DVD CD Video CD HDD Play Mode Search Mode A-B Repeat Repeat Program A (Loop Start) B (Loop End) Off ALL Play Mode Search Mode A-B Repeat Repeat Program Repeat Disc Repeat Title Repeat Chapter Repeat Off VR mode DVD-Video Video mode HDD CD Video CD S uper VCD MP3 DVR-433H_UK.book 58 ページ ２００５年３月１日　火曜日　午後５時６分
Playback 06 59 En Program play This feature lets you program the play order of titles/ chapters 1 /folders/tracks on a disc or the HDD. 1 Select ‘Program’ from the Play Mode menu. 2 Select ‘Input/Edit Program’ from the list of program options. The Program edit screen that appears depends on the kind of disc loaded. On the left side is the program list, then to the right is a list of titles (DVD, HDD), folders (WMA/MP3), or tracks (CD, Video CD/Super VCDs). On the far right is a list of chapters (DVD, HDD) or tracks (WMA/MP3). 3 Select a title, chapter, folder or track for the current step in the program list. DVD or HDD: You can add a whole title, or a chapter within a title to the program list. • To add a title, select the title. • To add a chapter, first highlight the title, then press  and select a chapter from the list. CD or Video CD /Super VCD : Select a track to add to the program list. WMA/MP3: You can add a whole folder, or a track within a folder to the program list. • To add a folder, select the folder. • To add a track, first highlight the folder, then press  and select a track from the list. After pressing ENTER to add the title/chapter/folder/ track, the step number automatically moves down one. • To insert a step into the program list, highlight the step number where you want to insert another step, then select a chapter/title/folder/track as usual. After pressing ENTER , all the subsequent steps move down one. • To delete a step from the program list, highlight the step you want to delete, then press CLEAR . 4 Repeat step 3 to build up a program list. A program list can contain up to 24 titles/chapters/ folders/tracks. 5 To play the program list, press  . Program play remains active until you turn off program play (see below), erase the program list (see below), eject the disc or switch off the recorder. • You can use repeat play with program play. Start playback of the program list then select Program Repeat from the Repeat Play Mode menu (see Repeat play on page 58). Note 1. When playing a program list of DVD-Video chapters, chapters not included in the program list may be sometimes be played, depending on the disc. DVD-Video HDD CD Video CD S uper VCD MP3 Play Mode Search Mode A-B Repeat Repeat Program Input/Edit Program Start Program Play Cancel Program Play Erase Program List Program Step 01.001 02. 03. 04. 05. 06. 07. 08. T itle (01-03) T itle 01 T itle 02 T itle 03 Chapter(001-015) Chapter 001 Chapter 002 Chapter 003 Chapter 004 Chapter 005 Chapter 006 Chapter 007 Chapter 008 Program T rack (01-10) T rack 01 T rack 02 T rack 03 T rack 04 T rack 05 T rack 06 T rack 07 T rack 08 T otal Time 0.00.00 Step 01.04 02. 03. 04. 05. 06. 07. 08. Program Step 01.01 02. 03. 04. 05. 06. 07. 08. Folder (01-03) 01.Rock 02.Pop 03.Dance Tr ack(001-004) 001.Intro 002.Escape 003.Everything You Say 004.What I Do DVR-433H_UK.book 59 ページ ２００５年３月１日　火曜日　午後５時６分
Playback 06 60 En Tip • To save your program list and exit the program edit screen without starting playback, press HOME MENU . • You can change the program list by selecting Input/ Edit Program from the Play Mode Program menu. • During program play, press  to skip to the next program step. • Press CLEAR during playback to switch off program play (if no menu OSD, such as the Disc Navigator, is displayed). Press while stopped to erase the program list. Other Program play functions As well as creating and editing a program list, you can start program play, cancel program play, and erase the program list from the Play Mode menu. 1 Press HOME MENU, select ‘Play Mode’, then ‘Program’. 2 Select a program play function. • Input/Edit Program – See above • Start Program Play – Starts playback of a saved program list • Cancel Program Play – Turns off program play, but does not erase the program list • Erase Program List – Erases the program list and turns off program play Displaying and switching subtitles Some DVD discs have subtitles in one or more languages; the disc box will usually tell you which subtitle languages are available. You can switch subtitle language during playback. 1 Check the disc packaging for details of the subtitle options. 1 Press SUBTITLE (SHIFT 2) repeatedly to select a subtitle option. The current subtitle language is shown on-screen and in the front panel display. 2 To switch off subtitles, press SUBTITLE (SHIFT 2) then CLEAR. Note 1. • Some discs only allow you to change subtitle language from the disc menu. Press TOP MENU or MENU to access. • To set subtitle preferences, see Subtitle Language on page 96. DVD-Video STANDBY/ON TOP MENU MENU DISC NAVIGA TOR HOME MENU HDD/DVD TV/DVD DISPLAY RETURN AUDIO HELP CLEAR INPUT SELECT SUBTITLE ANGLE S HOW V IEW CHANNEL SKIP TV DRECT REC ENTER REC MODE ST0P REC REC SHIFT ONE TOUCH COPY BACK CM     Subtitle: 1/2 English The toucan lives in tropical forests DVR-433H_UK.book 60 ページ ２００５年３月１日　火曜日　午後５時６分
Playback 06 61 En Switching DVD soundtracks When playing a DVD disc recorded with two or more soundtracks (often in different languages), you can switch the soundtrack during playback. 1 Check the disc packaging for details of the soundtrack options. • Press AUDIO (SHIFT 1) repeatedly to select an audio soundtrack. • The sound may drop out for a few seconds when switching soundtracks. • Some discs feature both Dolby Digital and DTS soundtracks. There is no analog audio output when DTS is selected. To listen to the DTS soundtrack, connect this recorder to a DTS decoder or AV amp/ receiver with built-in DTS decoder via the digital output. See Connecting to an AV amplifier/receiver on page 19 for connection details. Switching audio channels For HDD 2 and VR mode content recorded with bilingual audio, you can switch between left ( L ) channel, right ( R ) channel, or both ( L R ). 3 When playing Video CDs and audio CDs you can switch between stereo, just the left channel or just the right channel. Some Super VCDs have two soundtracks. With these discs you can switch between the two soundtracks as well as individual channels in each. • To display/switch the audio channel, press AUDIO (SHIFT 1) repeatedly. The audio channel(s) currently playing are indicated on- screen. • L R – Both channels (default) • L – Left channel only • R – Right channel only • Stereo – Stereo (default) • 1/L – Left channel only • 2/R – Right channel only Note 1. • Some discs only allow you to change audio language from the disc menu. Press TOP MENU or MENU to access. • To set audio language preferences, see Audio Language on page 96. DVD-Video TOP MENU MENU DISC NAVIGA TOR HOME MENU TV/DVD DISPLAY RETURN AUDIO HELP CLEAR INPUT SELECT SUBTITLE ANGLE S HOW V IEW CHANNEL SKIP TV DRECT REC ENTER REC MODE ST0P REC REC SHIFT ONE TOUCH COPY BACK CM    Audio : 1/2 Dolby Digital 2/0CH 2. Only when HDD Recording Format is set to Video Mode Off ( HDD Recording Format on page 97). 3. When playing a Bilingual recording on a VR mode disc, if you are listening to the Dolby Digital soundtrack via the digital output, you cannot switch the audio channel. Set Dolby Digital Out to Dolby Digital  PCM (see Dolby Digital Out on page 95) or listen via the analog outputs if you need to switch the audio channel. VR mode HDD CD Video CD S uper VCD MP3 TOP MENU MENU DISC NAVIGA TOR HOME MENU RETURN AUDIO SUBTITLE ANGLE S HOW V IEW CHANNEL SKIP ENTER REC MODE ST0P REC REC SHIFT ONE TOUCH COPY BACK CM    VR mode HDD CD Video CD MP3 DVR-433H_UK.book 61 ページ ２００５年３月１日　火曜日　午後５時６分
Playback 06 62 En • 1 Stereo – Soundtrack 1 / Stereo (default) • 1 L – Soundtrack 1 / Left channel • 1 R – Soundtrack 1 / Right channel • 2 Stereo – Soundtrack 2 / Stereo • 2 L – Soundtrack 2 / Left channel • 2 R – Soundtrack 2 / Right channel Switching camera angles Some DVD-Video discs feature scenes shot from two or more angles—check the disc box for details: it should be marked with a icon if it contains multi-angle scenes. When a multi-angle scene is playing, the same icon appears on screen to let you know that other angles are available (this can be switched off if you prefer—see Angle Indicator on page 98). • To switch the camera angle, press ANGLE (SHIFT 3). • The angle number is displayed on-screen. • If the disc was paused, playback starts again with the new angle. • Repeat play is canceled if you change the angle while repeat playback is active. • You can also change the angle from some DVD-Video disc menus. Press TOP MENU or MENU to access. S uper VCD DVD-Video TOP MENU MENU DISC NAVIGA TOR HOME MENU RETURN AUDIO SUBTITLE ANGLE S HOW V IEW CHANNEL SKIP TV DRECT REC ENTER REC MODE ST0P REC REC SHIFT ONE TOUCH COPY BACK CM    DVR-433H_UK.book 62 ページ ２００５年３月１日　火曜日　午後５時６分
Copying and back-up 07 63 En Chapter 7 Copying and back-up Introduction Use the copying features of this recorder to: • Back up important recordings stored on the HDD to a DVD. • Make a DVD copy of a recording on the HDD to play in another player. • Transfer video from a DVD to the HDD for editing. • Transfer edited video from the HDD to DVD. The simplest way to copy a title is to use the One Touch Copy feature. This copies the currently playing HDD title to DVD, or DVD title to the HDD. See One Touch Copy on page 63 for detailed instructions. For more sophisticated copying tasks you can build a Copy List of titles to copy, and edit titles so that you only copy the bits you want. See Using Copy Lists on page 64 for detailed instructions. Where possible, the recorder will copy your recordings at high-speed. Depending on the recording mode, the kind of disc loaded and various other factors, copying can be as fast as one minute per hour of video. See Minimum copying times on page 102 for more on copying times. If you want to save disc space you can copy video at a lower recording quality (for example, an XP recording on the HDD copied to SP on a DVD). Copying in this way is always done in real-time. When real-time copying from the HDD to a Video mode DVD, the chapter markers in the original material are not copied. Chapter markers are put into the copy at intervals, according to the Auto Chapter (Video) setting (see also Auto Chapter (Video) on page 97). Restrictions on copying Some video material is copy-once protected. This means that it can be recorded to HDD, but it can’t then be freely copied again. If you want to transfer copy-once protected material from HDD to DVD, you’ll need to use a VR mode disc compatible with CPRM Ver. 1.1 or higher (see CPRM on page 38 for more on this). Only one instance of a copy- once protected title can be added to the Copy List, and after it’s been copied, the title is erased from the HDD (it is therefore not possible to copy a locked title that is copy- once protected). You can identify copy-once protected material during playback by displaying disc information on-screen. If the current title is copy-once protected, an exclamation mark ( ! ) is shown (see Play display 2 on page 36). Copyright Recording equipment should be used only for lawful copying and you are advised to check carefully what is lawful copying in the country in which you are making a copy. Copying of copyright material such as films or music is unlawful unless permitted by a legal exception or consented to by the rightowners. One Touch Copy * See also Copyright above. The One Touch Copy feature copies the currently playing or selected (in the Disc Navigator) HDD title to DVD, or DVD title to HDD. The whole title is copied, regardless of where in the title you start the copy. HDD to DVD copies are made in the same recording mode. When copying DVD to HDD, the copy is made in whatever recording mode is currently set. Make sure that a recordable DVD-R/RW disc is loaded when trying to copy from the HDD. 1 If you’re copying from DVD to the HDD, use the REC MODE (SHIFT  ) button to select a recording mode. Note that selecting a recording mode higher than the title playing will not result in a better quality recording. 2 During playback, press ONE TOUCH COPY to copy the current title. The front panel display indicates that the title is being copied. • High-speed copying is used when copying from the HDD to DVD. Playback continues while copying. • Real-time copying is used when copying from DVD to the HDD. Playback restarts from the beginning of the title. DVD RECORDER SKIP TV DRECT REC REC MODE ST0P REC REC SHIFT ONE TOUCH COPY BACK CM  DVR-433H_UK.book 63 ページ ２００５年３月１日　火曜日　午後５時６分
Copying and back-up 07 64 En Canceling One Touch Copy You can cancel a One Touch Copy once it’s started. • Press and hold ONE TOUCH COPY for more than a second. Copying is canceled and the video already copied is erased. • If you cancel a HDD to DVD-R copy, the space available for recording does not return to the pre- copy figure. Notes on copying using One Touch Copy Copying to DVD • Title name, chapter markers, as well as thumbnail picture markers for the Disc Navigator, are also copied. However, if you copy to a Video mode DVD-R/ RW, only the first 40 characters of a name are copied. • The chapter markers in the copy may not be in exactly the same positions as the original when recording on to a Video mode disc. • You can’t use the One Touch Copy function to copy a title if any part of the title is copy-once protected. •A title that contains mixed aspect ratios can’t be copied to a Video mode disc. Use a VR mode disc for this type of material. • Low resolution ( SEP through LP modes 1 ) widescreen material can’t be copied to a Video mode disc. Use a VR mode disc for this type of material. • When HDD Recording Format is set to Video Mode Off, titles recorded in LP / MN9 – 15 modes cannot be high-speed copied to a Video mode DVD. Please use a VR mode disc. • Recordings of bilingual broadcasts cannot be high- speed copied to a Video mode DVD. Please use a VR mode disc. • XP titles cannot be copied to DVD at high-speed. Copying to the HDD • The maximum title length for copying is 12 hours. • Title name and chapter markers are also copied, except when copying from a finalized Video mode disc. • Thumbnail picture markers and chapter markers for the Disc Navigator are copied, but their position in the copy may be slightly changed from the original. • If some part of the title being copied is copy- protected, copying will start, but the copy-protected portions will not be copied. Using Copy Lists * See also Copyright on page 63. At its simplest, a Copy List is just a list of HDD or DVD titles that you want to copy. When copying HDD titles to DVD, you can, however, edit the titles in your copy list, erasing chapters you don’t need, or re-naming titles, for example. Edits you make to titles in the Copy List do not affect the actual video content; only the ‘virtual’ content of the Copy List. So you can freely erase and modify anything in your Copy List safe in the knowledge that the actual content is not being altered. Copying from HDD to DVD Important • The recorder can only store one Copy List at a time. • The Copy List is erased if the Input Line System setting is changed (see Additional information about the TV system settings on page 99). • Resetting the recorder to its factory settings (see Resetting the recorder on page 111) will erase the Copy List. 1 Press HOME MENU and select ‘Copy’. Note 1. In manual recording mode these equate to MN1–15 (Video Mode Off) or MN1–11 (Video Mode On). TOP MENU MENU DISC NAVIGA TOR HOME MENU RETURN S HOW V IEW SKIP TV DRECT REC ENTER REC MODE ST0P REC REC SHIFT ONE TOUCH COPY BACK CM    T imer Recording Photo Viewer Disc Setup Play Mode Disc Navigator Initial Setup Video/Audio Adjust Copy Jukebox DVR-433H_UK.book 64 ページ ２００５年３月１日　火曜日　午後５時６分
Copying and back-up 07 65 En 2 Select ‘HDD  DVD’. If this is the first time to create a Copy List, skip to step 4 below. 3 If there is already a Copy List stored in the recorder, choose whether to ‘Create New Copy List’ or ‘Use Existing Copy List’. If you select Use Existing Copy List , skip to step 8 below. • Selecting Create New Copy List will erase any Copy List already stored in the recorder. 4 Select VR mode or Video mode for the copy. For certain kinds of material you must use VR mode; for greater compatibility with other players, use Video mode. 5 Use the / buttons to highlight titles you want to copy, pressing ENTER after each one to add it to the Copy List. Titles you’ve added to the Copy List are highlighted in pink. There are some restrictions on titles that can be added to the Copy List if you are copying to a Video mode DVD: • When adding titles that contain copy-once protected material, the copy-once parts will not be added. • When adding titles that contain material of more than one aspect ratio (screen size), each part with a different aspect ratio will be added as a separate title if high-speed copying is possible. Depending on the title 1 , high-speed copying may not be possible to a Video mode disc. 6 Press  to display the command menu panel. Copy HDD DVD Disc Back-up DV Record DVD/CD HDD Copy Use Existng Copy List Create New Cppy List Copy Select Recording Format Please select the recording format for the disc. HDD DVD VR Mode Video Mode High compatibility mode. Must be final- ized for playback on other equipment. Copying of bilingual broadcasts and copy-once protected material is possible. Note 1. • Widescreen titles recorded at low resolution ( SEP through LP / MN1–15 (Video Mode Off) or MN1–11 (Video Mode On). • LP / MN9 – 15 recordings when HDD Recording Mode is set to Video Mode Off. • Bilingual recordings. • Combined titles that were originally recorded using different recording modes. • XP titles. Copy Select Title Recent first All Genres 10 Title Return Copy List T otal Current DVD Remain 1.2G 1.2G 10 9 8 7 6 5 4 3 MON 29/11 19:00 Mon 29/11 Pr 2 SP MON 29/11 19:00 Mon 29/11 Pr 2 SP MON 29/11 19:00 Mon 29/11 Pr 2 SP MON 29/11 19:00 Mon 29/11 Pr 2 SP MON 29/11 19:00 Mon 29/11 Pr 2 SP MON 29/11 19:00 Mon 29/11 Pr 2 SP MON 29/11 19:00 Mon 29/11 Pr 2 SP MON 29/11 19:00 Mon 29/11 Pr 2 SP Next 19:00 Mon 29/11 Pr 2 SP 19:00 2h00m(1.0G) HDD DVD (Video mode) Copy Select Title Recent first All Genres 10 Title Return Copy List T otal Current DVD Remain 1.2G 1.2G 10 9 8 7 6 5 4 3 Confirm Next MON 29/11 19:00 Mon 29/11 Pr 2 SP MON 29/11 19:00 Mon 29/11 Pr 2 SP MON 29/11 19:00 Mon 29/11 Pr 2 SP MON 29/11 19:00 Mon 29/11 Pr 2 SP MON 29/11 19:00 Mon 29/11 Pr 2 SP MON 29/11 19:00 Mon 29/11 Pr 2 SP MON 29/11 19:00 Mon 29/11 Pr 2 SP MON 29/11 19:00 Mon 29/11 Pr 2 SP 19:00 Mon 29/11 Pr 2 SP 19:00 2h00m(1.0G) HDD DVD (Video mode) Next The Command Menu panel DVR-433H_UK.book 65 ページ ２００５年３月１日　火曜日　午後５時６分
Copying and back-up 07 66 En 7 Select ‘Next’ to move on to the Title Edit screen. 8 To edit a title, highlight it using the / buttons, then press ENTER. A menu of editing commands appears: • Erase – Erase individual titles from the Copy List (see page 67). • Title Name – Name or rename a title in the Copy List (see page 67). • Erase Section – Erase part of a title (see page 68). • Move – Change the order of titles in the Copy List (see page 68). • Preview – Check the content of a title in the Copy List (see page 69). • Divide – Divide a title in the Copy List into two (see page 69). • Combine – Combine two titles in the Copy List into one (see page 69). • Chapter Edit – Edit chapters within a Copy List title (see page 69): • Divide – Divide a chapter into two. • Erase/Move – Erase a chapter/Change the chapter order. • Combine – Combine two chapters into one. • Set Thumbnail – Set the thumbnail frame for a title (see page 70). • Recording Mode – Set the picture quality of the copy (see page 70). • Bilingual – Set how bilingual audio should be copied when copying from HDD to Video mode DVD (see page 71). • Cancel – Exit the Copy List screen without saving any changes. Repeat this step for as many titles you have that need editing. 9 Press  to display the command menu panel. 10 Select ‘Next’ to proceed to the Start Copy screen. • Select Recording Mode if you want to change the recording quality (see Recording Mode on page 70). • Select Input Disc Name if you want to change the disc name. Input a name of up to 64 characters for a VR mode disc or 40 characters for a Video mode disc. (The input method is similar to that of naming titles; see Title Name on page 67.) • Select Finalize if you want to automatically finalize a Video mode DVD after copying. 1 Select a title menu style from the following screen. 11 Select ‘Start Copy’ to start copying. Copy Edit Title 3 Title Return Copy List T otal Current DVD Remain 1.2G 1.2G 1 2 3 19:00 Mon 29/11 Pr 2 SP 19:00 Mon 29/11 Pr 2 SP 19:00 Mon 29/11 Pr 2 SP Next 19:00 Mon 29/11 Pr 2 SP 2h00m(1.0G) HDD DVD (Video mode) 1 19:00 Mon 29/11 Pr 2 SP Copy Edit Title 3 Title Return Copy List T otal Current DVD Remain 1.2G 1.2G 1 2 3 19:00 Mon 29/11 Pr 2 SP 19:00 Mon 29/11 Pr 2 SP 19:00 Mon 29/11 Pr 2 SP Next 19:00 Mon 29/11 Pr 2 SP 2h00m(1.0G) HDD DVD (Video mode) 1 19:00 Mon 29/11 Pr 2 SP Erase Tit le Name Erase Section Move Preview Cancel Note 1. If a timer recording is scheduled to start during copying, the disc will not be finalized. Copy Edit Title 3 Title Return Copy List T otal Current DVD Remain 1.2G 1.2G 1 2 3 19:00 Mon 29/11 Pr 2 SP 19:00 Mon 29/11 Pr 2 SP 19:00 Mon 29/11 Pr 2 SP Confirm Next 19:00 Mon 29/11 Pr 2 SP 2h00m(1.0G) HDD DVD (Video mode) Next Copy HDD DVD (Video Mode) Start Copy Copy Time 0h00m Recording Mode Disc Name Finalize Return Recording Mode Input Disc Name Finalize Start Copy Copy List T otal Current DVD Remain 1.2G 1.2G DVD-RW HDD SP Off DVR-433H_UK.book 66 ページ ２００５年３月１日　火曜日　午後５時６分
Copying and back-up 07 67 En Copying from DVD to HDD Important • The DVD to HDD Copy screen isn’t accessible when a finalized Video mode disc is loaded. However, you can still use the One Touch Copy function (See One Touch Copy on page 63). • The recorder can only store one Copy List at a time. • The Copy List will be erased if: – any of the titles on the DVD disc are erased or edited. – the disc tray is opened. – playback is switched between Play List and Original. – the DVD disc is re-initialized or finalized. – the recorder is reset to its factory settings (see Resetting the recorder on page 111). • It may not be possible to copy from a DVD disc that was recorded on a different DVD recorder or a PC. 1 Press HOME MENU and select ‘Copy’. 2 Select ‘DVD/CD  HDD’. 3 If there is already a Copy List stored in the recorder, choose whether to ‘Create New Copy List’ or ‘Use Existing Copy List’. • Selecting Create New Copy List will erase any Copy List already stored in the recorder. 4 Use the / buttons to highlight titles you want to copy, pressing ENTER after each one to add it to the Copy List. Titles you’ve added to the Copy List are highlighted in pink. 5 Press  to display the command menu panel. 6 Select ‘Next’ to move on to the Title Edit screen. 7 To edit a title, highlight it using the / buttons, then press ENTER. A menu appears of Copy List editing commands: • Erase – Erase individual titles from the Copy List (see page 67). • Move – Change the order of titles in the Copy List (see page 68). • Preview – Check the content of a title in the Copy List (see page 69). • Cancel – Exit the Copy List screen without saving any changes. Repeat this step for as many titles you have that need editing. 8 Press  to display the command menu panel. 9 Select ‘Next’ to proceed to the Start Copy screen. • Select Recording Mode if you want to change the recording quality (see Recording Mode on page 70). 10 Select ‘Start Copy’ to start copying. Erase Use this command to erase individual titles from the Copy List. 1 Highlight the title you want to erase. 2 Select ‘Erase’ from the command menu panel. 3 Select ‘Yes’ to confirm or ‘No’ to cancel, then press ENTER. Tip • You can erase a title quickly by pressing CLEAR when the title is highlighted. Confirm the edit by pressing ENTER . Title Name Use this command to name or rename titles in the Copy List (the names of the original titles remain unchanged). When copying to a Video mode disc, the name length is limited to 40 characters; for a VR mode disc, the limit is 64 characters. 1 Highlight the title you want to name (or rename). 2 Select ‘Title Name’ from the command menu panel. 3 Input a name for the selected title. • Use the /// and ENTER to select characters. •A name generated automatically by the recorder will already be in the name input section of the screen. Use the / buttons to change the cursor position. Yes Erase ? No ! Input Title Name CAPS small OK Clear Space A B C D E F G H I J K L M . , ? ! N O P Q R S T U V W X Y Z ( ) : ; A A A A A A Æ ç E E E E I I I I # 2 3 ´ µ ¶ · 1 ¿ ` D N O O O O O ø U U U U Y ß $ % 0 1 2 3 4 5 6 7 8 9 < = > _ & £ \ § ¨ © ¬ – ® _ ˚ – / @ [ ¥ ] ˆ ÷ x ± { | } ~ ¡ c a – o – << << 1 / 4 1 / 2 3 / 4 ¸ 1 2:30 Wed 4/11 Pr 5 LP DVR-433H_UK.book 67 ページ ２００５年３月１日　火曜日　午後５時６分
Copying and back-up 07 68 En • Select CAPS or small to change to upper or lower- case, or use the CASE SELECTION buttons ( /  ). • You can also use the CLEAR button to delete characters directly (press and hold for two seconds to delete the whole name). For other remote control key shortcuts, see Using the remote key shortcuts to input a name on page 76. • For discs formatted on a different DVD recorder, you will see only a limited character set. 4 Highlight ‘OK’ then press ENTER to enter the name and return to the Copy List. • To return to the main Copy List screen without saving changes to the title name, press RETURN . Erase Section Using this command you can delete a part of a Copy List title, ideal for cutting out the commercial breaks in a recording made from the TV. 1 Highlight the title containing the section you want to erase. 2 Select ‘Erase Section’ from the command menu panel. The Erase Section screen appears from which you can mark the start and end points of the section to erase. 3 Select the type of edit. • Video Mode Compatible Editing – Edit points cannot be set with absolute precision, but high- speed copying to Video mode DVD will be possible. • Frame Accurate Editing – Exact edit points are preserved, but high-speed copying to Video mode DVD will not be possible. • For more information about these options, see Editing accuracy on page 74 4 Highlight ‘From’ then use the playback controls (  ,  ,  ,  , etc.) to find the start of the section to erase, then press ENTER. The bar at the bottom of the screen indicates the current play position in the title. After pressing ENTER , a marker shows the start of the section. 5 Highlight ‘To’ then, in the same way, find the end of the section to erase, then press ENTER. After pressing ENTER , another marker indicates the end of the section, with the section itself marked in red. 6 Select ‘Yes’ to confirm, or ‘No’ to cancel, then press ENTER. In the thumbnail viewer you can see a few seconds of video either side of the marked section to see how the edit will look. Move Use this command to change the order of titles in the Copy List. 1 Highlight the title you want to move and press ENTER. 2 Select ‘Move’ from the command menu panel. 3 Move the insert bar to the new position for the title and press ENTER. ! Video Mode Compatible Editing Frame Accurate Editing DVD RECORDER Please select the type of editing. Video Mode Compatible Editing is recommended for compatibility with high-speed copying. Erase Section (HDD Copy)  Play Pause Rec. time 0h01m 5-1 19:00 Mon 29/11 Pr 2 SP Exit From To 00.00.09.15 Yes Erase ? No ! Copy Edit Title 3 Title Return Copy List T otal Current DVD Remain 1.2G 1.2G 1 2 3 19:00 Mon 29/11 Pr 2 SP 19:00 Mon 29/11 Pr 2 SP 19:00 Mon 29/11 Pr 2 SP Next 19:00 Mon 29/11 Pr 2 SP 2h00m(1.0G) HDD DVD (Video mode) Insertion position Title to move DVR-433H_UK.book 68 ページ ２００５年３月１日　火曜日　午後５時６分
Copying and back-up 07 69 En Preview Use this command to check what’s in a title. 1 Highlight the title you want to preview. 2 Select ‘Preview’ from the command menu panel. The selected title starts to play. Use any of the usual playback controls to scan, skip, play in slow-motion, etc. 3 To get back to the Copy List, press RETURN. Divide Use this command to make two titles from a title already in the Copy List. 1 Highlight the title you want to divide. 2 Select ‘Divide’ from the command menu panel. 3 Select the type of edit. • Video Mode Compatible Editing – Edit points cannot be set with absolute precision, but high- speed copying to Video mode DVD will be possible. • Frame Accurate Editing – Exact edit points are preserved, but high-speed copying to Video mode DVD will not be possible. • For more information about these options, see Editing accuracy on page 74 4 Use the playback controls (  ,  ,  ,  , etc.) to find the place you want to divide the title. 5 Press ENTER to divide the title at the current playback position. Combine Use this command to make a single title from two titles in the Copy List. The second title selected will be appended to the first. 1 Highlight the title you want to combine with another, then press ENTER. This title will not move. The next title you select will be appended to this one. 2 Select ‘Combine’ from the command menu panel. 3 Select the title you want to append to the first, then press ENTER. This title will effectively move to be added to the end of the first title. In the example below, title 3 will be appended to title 1. 4 Select ‘Yes’ to confirm or ‘No’ to cancel, then press ENTER. Chapter Edit The Chapter Edit option gives you access to several commands that you can use to edit chapters within a Copy List title. 1 Highlight the title that contains the chapters you want to edit. 2 Select ‘Chapter Edit’ from the command menu panel. 3 Select the type of editing. ! Video Mode Compatible Editing Frame Accurate Editing DVD RECORDER Please select the type of editing. Video Mode Compatible Editing is recommended for compatibility with high-speed copying. Divide Title (HDD Copy)  Play Pause Rec. time 0h01m 5–1 19:00 Mon 29/11 Pr 2 SP Cancel 00.00.09.15 Divide Copy Edit Title 3 Title Return Copy List T otal Current DVD Remain 1.2G 1.2G 1 2 3 19:00 Mon 29/11 Pr 2 SP 19:00 Mon 29/11 Pr 2 SP 19:00 Mon 29/11 Pr 2 SP Next 19:00 Mon 29/11 Pr 2 SP 2h00m(1.0G) HDD DVD (Video mode) This title will not move This title will be appended Yes OK to combine titles 1 and 3 ? No ! ! Video Mode Compatible Editing Frame Accurate Editing DVD RECORDER Please select the type of editing. Video Mode Compatible Editing is recommended for compatibility with high-speed copying. DVR-433H_UK.book 69 ページ ２００５年３月１日　火曜日　午後５時６分
Copying and back-up 07 70 En • Video Mode Compatible Editing – Edit points cannot be set with absolute precision, but high- speed copying to Video mode DVD will be possible. • Frame Accurate Editing – Exact edit points are preserved, but high-speed copying to Video mode DVD will not be possible. • For more information about these options, see Editing accuracy on page 74 4 Select the command you want: • Divide – Divide a chapter into two or more parts: Use the playback controls (  ,  ,  ,  , etc.) to find the point at which you want to divide the chapter, then press ENTER . You can keep dividing the chapter as many times as you wish (up to 99 per title). • Erase/Move – Erase or move chapters: Select the chapter you want to erase/move and press ENTER . Select whether you want to erase or move the chapter. Move command only: Select the destination for the chapter, and press ENTER . • Combine – Combine two adjacent chapters into one: Highlight the bar divider between two adjacent chapters and press ENTER . 5 Select ‘Exit’ to get back to the main Copy List screen. Set Thumbnail You can change the thumbnail picture that appears in the four-title display of the Disc Navigator for a title to any frame that appears in that title. 1 Highlight the title you want to change the thumbnail picture for. 2 Select ‘Set Thumbnail’ from the command menu panel. The thumbnail setting screen appears from which you can find the frame you want. 3 Use the playback controls (  ,  ,  ,  , etc.) to find a suitable frame, then press ENTER to set. You can also use the CM SKIP ( SHIFT  ) buttons. 4 Select ‘Exit’ to return to the Copy List screen. Recording Mode 1 Select ‘Recording Mode’ from the command menu panel. 2 Use the / buttons to select a recording mode for the copy. • High-Speed Copy 1 – The Copy List is copied at the same recording quality as the original. • XP , SP , LP , EP , SLP , SEP , MN 2 – The Copy List is copied at the specified recording quality in real-time. (Note that if you copy at a higher quality setting than the original, the copy will not be better quality than the original.) If you select MN above, you can also change the level setting ( MN1 – MN32 , LPCM or XP 3 ) from the Recording Quality box that appears. • Optimized 2,4 – The recording quality is automatically adjusted so that the Copy List fits on to the space available on the disc. Copying is carried out in real- time. Edit Chapter (HDD Copy) Rec. time Chapters 1–1  Play 0.00.00 18:00 Mon 29/11 Pr 1 XP 1h00m 10 Exit Erase/Move Combine Divide Edit Chapter (HDD Copy) 002 003 005 004 001 Rec. time Chapter 19:00 Mon 29/11 Pr 2 SP 1h00m 0h01m Exit Erase/Move Combine Divide Move Cancel Erase Edit Chapter (HDD Copy) 002 003 005 004 001 Rec. time 19:00 Mon 29/11 Pr 2 SP 1h00m Exit Erase/Move Divide Erase/Move Combine Note 1. When copying to a Video mode DVD, the chapter markers in the copy may not be in exactly the same position as the original. 2. When the copy mode is set to something other than High-Speed Copy for copying to a Video mode DVD, the chapter markers of the original are not copied. Chapter markers are put into the copy at regular intervals, according to the Auto Chapter setting (see also Auto Chapter (Video) on page 97). 3. XP mode available only when copying to HDD. 4. Optimized mode only available when copying to DVD. Set Thumbnail (HDD Copy)  Play Pause Rec. time 0h01m 5-1 19:00 Mon 29/11 Pr 2 SP Exit 00.00.09.15 OK DVR-433H_UK.book 70 ページ ２００５年３月１日　火曜日　午後５時６分
Copying and back-up 07 71 En When you change the recording mode setting, you can see how much disc space it will require. If this is more than is available, it shows up in red and you won’t be able to start copying. In this case, either change the recording quality, or press RETURN to go back to the Copy List screen and erase one or more titles from the Copy List. 3 Press ENTER. Bilingual 1 Select the title containing the audio you want to change. 2 Select ‘Bilingual’ from the command menu panel. 3 Use the / buttons to select a bilingual audio option. 4 Press ENTER. Using disc back-up * See also Copyright on page 63. This feature offers a simple way to make a back-up copy of a finalized Video mode disc. The data is copied first to the hard disk drive 1 , then on to another recordable DVD disc. 1 Press HOME MENU, select ‘Copy’, then ‘Disc Back- up’. 2 Select a back-up option. There are three back-up options: • Start new disc back-up – Start making a back-up of a disc. • Resume writing data – Record the back-up data already on the HDD to a recordable DVD. • Erase back-up data – Erase the back-up data on the HDD. 3 Press  OPEN/CLOSE (front panel) to open the disc tray and load the disc you want to make a back- up of, then close the disc tray. You can only make back-up copies of finalized Video mode discs. 4 Select ‘Start’. • To see the progress of the back-up, press DISPLAY ( SHIFT HELP ). • You can cancel the back-up process by pressing ONE TOUCH COPY for more than one second. 5 When the data has been copied, press  OPEN/ CLOSE (front panel) to open the disc tray. Take out the disc and load a blank* recordable DVD. * If you’re using a DVD-RW, the disc doesn’t have to be blank, although the previous contents of the disc will be erased in the back-up process. You can use a DVD-R Ver. 2.0 or 2.1 disc, or DVD-RW Ver. 1.1 or Ver. 1.2 disc for the back-up. • If you back-up a DVD-R disc to DVD-RW, you cannot undo the finalization later. • Actual recordable capacity of discs vary so there may be cases where the contents of the disc you’re backing-up will not fit on to a particular blank disc. If this happens, please try another brand of disc. Note 1. It is not possible to play this material directly from the HDD. Disc Back-up Start new disc back-up Resume writing date Erase back-up date No Disc. Please load a disc to be backed-up. Start Cancel Disc Back-up Read from disc and save to HDD. Start reading? Start Cancel Disc Back-up Disc content saved to Hard Disk Drive. Please eject the disc and load a recordable disc Start Cancel Disc Back-up DVR-433H_UK.book 71 ページ ２００５年３月１日　火曜日　午後５時６分
Copying and back-up 07 72 En 6 Select ‘Start’ to start writing the backed-up data to the blank disc. • To see the progress of the back-up, press DISPLAY ( SHIFT HELP ). • You can cancel the back-up process by pressing ONE TOUCH COPY for more than one second. However, this will make the disc unusable (although if you are using a DVD-RW disc you can re-initialize it in order to make it usable again—see Initializing a recordable DVD disc on page 52.) 7 After the recorder has finished recording the back-up disc, you can select whether to make another back-up of the same data or exit. • Select Start to make another back-up copy or Cancel to finish. If you want to make another back-up copy, return to step 6 above. 8 If you don’t need to keep the back-up data on the HDD, you can delete it now. Select Yes to delete the data from the HDD; select No to keep it (you can delete it later if you want to). • If you decide to leave the back-up data on the HDD, you can make back-up copies to recordable DVD discs anytime from the Disc Back-up menu. Write back-up data from Hard Disk Drive. The disc contents will be overwritten. OK to start? Start Cancel Disc Back-up Disc back-up finished. To make another back-up copy, please load a recordable disc. Start Cancel Disc Back-up The backed-up data is still on the HDD. Erasing it will increase the free space available. OK to Erase? Ye s No Disc Back-up DVR-433H_UK.book 72 ページ ２００５年３月１日　火曜日　午後５時６分
Editing 08 73 En Chapter 8 Editing The Disc Navigator screen The Disc Navigator screen is where you can edit video content on unfinalized Video mode and VR mode DVD discs 1 , as well as video content on the internal hard disk drive. Important • Titles that have been recorded with a Line Input setting different to the current setting of the recorder are shown in the Disc Navigator with a blank thumbnail image. See also Additional information about the TV system settings on page 99. • During recording, if you display the Disc Navigator for the HDD, some of the titles may appear with a mark. These titles were recorded with a Line Input setting different to the current setting of the recorder. During recording, these titles cannot be played. 1 Use the HDD/DVD button to select the HDD or DVD. 2 Press DISC NAVIGATOR to display the Disc Navigator screen. Playback will automatically stop when you do this. • You can also access the Disc Navigator from the Home Menu (press HOME MENU , select Disc Navigator then press ENTER ). • From the title list, press  to display the command menu panel. Use the / and ENTER buttons to navigate the menus. • When in the title list, use the  and  buttons to display the previous/next page if there are more titles than can be displayed. • Press DISPLAY ( SHIFT HELP ) to change the title information displayed in the title list. • If you are editing a VR mode disc you can display the Play List by selecting Play List from the view options panel (press  , then select Play List from the view options, then Play List ). • You can switch between the HDD and the DVD Disc Navigator screens using the HDD/DVD button. Titles on the HDD marked with a icon are timer recordings set to Auto Replace Recording (see Setting a manual timer recording on page 44). Titles on the HDD marked with a icon are recently recorded titles that haven’t yet been played. 3 To exit the Disc Navigator, press HOME MENU . Note 1. It isn’t possible to edit video on DVD-RAM discs using this recorder. STANDBY/ON TOP MENU MENU DISC NAVIGA TOR HOME MENU HDD/DVD TV/DVD DISPLAY RETURN AUDIO HELP CLEAR INPUT SELECT SUBTITLE ANGLE S HOW V IEW CHANNEL SKIP TV DRECT REC ENTER REC MODE ST0P REC REC SHIFT ONE TOUCH COPY BACK CM     Disc Navigator (HDD) 4 Titles Remain HDD SP Recent First All Genres 10Titles 30h30m 11/29 MON 7:00PM 11/29Mon 7:00PM 2ch SP 2h00m(1.0G) 1 20:00 FRI 3/12 20:00 Fri 3/12 Pr 9 SP 2h00m(1.0G) 22:00 THU 2/12 22:00 Thu 2/12 Pr 7 SP 1h00m(1.0G) 19:00 MON 29/11 19:00 Mon 29/11 Pr 2 SP 1h00m(1.0G) 23:00 FRI 3/12 23:00 Fri 3/12 Pr 4 SP 2h00m(1.0G) 9 8 7 10 View options panel Title list style Selected title Command menu panel Title thumbnail Title information Title list Title list order Genre selection Available recording time Disc Navigator (DVD) 4 Titles 10Titles Original 11/29 MON 7:00PM 11/29Mon 7:00PM 2ch SP 2h00m(1.0G) 1 20:00 FRI 3/12 20:00 Fri 3/12 Pr 9 SP 2h00m(1.0G) 23:00 FRI 3/12 23:00 Fri 3/12 Pr 4 SP 2h00m(1.0G) 9 10 Style 4 Titles PlayList Original DVR-433H_UK.book 73 ページ ２００５年３月１日　火曜日　午後５時６分
Editing 08 74 En Command menu panel options The table below shows which commands you can use with which video type. Editing accuracy Some editing (and Copy List) commands ask you whether you want to keep Video mode compatibility or frame accuracy ( Video mode compatible editing , or Frame accurate editing ). Frame accurate editing is very precise. The edit point is accurate to the exact frame you choose. However, this accuracy is not preserved in any copy you make if you use the high-speed copy function to make a Video mode DVD. Video mode compatible editing is less precise. The edit point you choose will only be accurate to within 0.5–1 second. On the other hand, these edit points will be preserved if you use high-speed copy to make a Video mode DVD. HDD genres The large capacity of the HDD means that there may be many hours of video in the recorder. To help you organize your HDD video content you can assign different genres to titles. There are five genres in total, including five user- definable ones that you can name as you like. HDD Video mode VR mode (Original) VR mode (Play List) Create (page 75)  Play (page 75)    Erase (page 75)    Edit > Title Name (page 75)    Edit > Set Thumbnail (page 76)    Edit > Erase Section (page 77)   Edit > Divide (page 77)  Edit > Chapter Edit (page 78)   Edit > Set Genre (page 79)  Edit > Lock (page 79)   Edit > Move (page 79)  Edit > Combine (page 80)  Genre Name (page 80)  Multi-Mode (page 80)  Undo (page 81)   DVR-433H_UK.book 74 ページ ２００５年３月１日　火曜日　午後５時６分
Editing 08 75 En Create Play List only Use this function to create a Play List and add titles to it. Before you can use this command, make sure that the Play List Pis switched on in the view options panel on the left. 1 Select ‘Create’ from the command menu panel. 2 Select a title to add to the Play List. Use the / buttons to highlight an Original title then press ENTER to add it and display the Play List. 3 Repeat steps 1 and 2 to add as many titles as necessary to the Play List. Play Use this function to start playback of a title. 1 Highlight the title you want to play. 2 Select ‘Play’ from the command menu panel. Playback of the title you selected starts. Erase Use this function to erase unwanted titles. When you erase titles from the HDD or Original titles from a VR mode DVD-RW, the available recording space increases accordingly. Erasing a title from a Video mode DVD-RW disc increases the available recording time only if it is the last title on the disc. Erasing Play List titles, or titles from a DVD-R, VR mode or Video mode, will not result in any more free space on the disc. 1 Highlight the title you want to erase. 2 Select ‘Erase’ from the command menu panel. 3 Select ‘Yes’ to confirm or ‘No’ to cancel, then press ENTER. Tip • You can erase a title quickly by pressing CLEAR when the title is highlighted. Confirm the edit by pressing ENTER . Title Name You can give titles new names of up to 64 characters long for VR mode and HDD recordings, and up to 40 characters for Video mode recordings. 1 Highlight the title you want to name (or rename). 2 Select ‘Edit’ > ‘Title Name’ from the command menu panel. VR mode Disc Navigator (DVD) 2h00m(1.0G) 1h00m(1.0G) 4 Titles Remain 10Titles 0h30m DVD VR Mode 2h00m(1.0G) Play List Play Erase Edit Create Undo No title HDD Video mode VR mode Disc Navigator (HDD) 4 Titles Remain HDD SP Recent First All Genres 10Titles 30h30m 11/29 MON 7:00PM 11/29Mon 7:00PM 2ch SP 2h00m(1.0G) 1 20:00 FRI 3/12 20:00 Fri 3/12 Pr 9 SP 2h00m(1.0G) 22:00 THU 2/12 22:00 Thu 2/12 Pr 7 SP 1h00m(1.0G) 19:00 MON 29/11 19:00 Mon 29/11 Pr 2 SP 1h00m(1.0G) 23:00 FRI 3/12 23:00 Fri 3/12 Pr 4 SP 2h00m(1.0G) 9 8 7 10 Play Erase Edit Genre Name Multi-Mode HDD Video mode VR mode HDD Video mode VR mode Disc Navigator (HDD) 4 Titles Remain HDD SP All Genres 10Titles 30h30m Recent First 11/29 MON 7:00PM 11/29Mon 7:00PM 2ch SP 2h00m(1.0G) 1 20:00 FRI 3/12 20:00 Fri 3/12 Pr 9 SP 2h00m(1.0G) 22:00 THU 2/12 22:00 Thu 2/12 Pr 7 SP 1h00m(1.0G) 19:00 MON 29/11 19:00 Mon 29/11 Pr 2 SP 1h00m(1.0G) 23:00 FRI 3/12 23:00 Fri 3/12 Pr 4 SP 2h00m(1.0G) 9 8 7 10 Play Erase Edit Multi-Mode Genre Name Cancel T itle name Erase Section Cancel Set Thumbnail Set Genre Lock Divide Chapter Edit DVR-433H_UK.book 75 ページ ２００５年３月１日　火曜日　午後５時６分
Editing 08 76 En 3 Input a name for the selected title. • Use the /// and ENTER to select characters. •A name generated automatically by the recorder will already be in the name input section of the screen. Use the / buttons to change the cursor position. • Select CAPS or small to change to upper or lower- case, or use the CASE SELECTION buttons ( /  ). • You can also use the CLEAR button to delete characters directly (press and hold for two seconds to delete the whole name). For other remote control key shortcuts, see Using the remote key shortcuts to input a name below. • For discs formatted on a different DVD recorder, you will see only a limited character set. 4 Highlight ‘OK’ then press ENTER to enter the name and return to the main Disc Navigator screen. • To return to the main Disc Navigator screen without saving changes to the title name, press RETURN . Using the remote key shortcuts to input a name The table below shows the remote control key shortcuts that you can use to input characters in the name input screen. Pressing a button repeatedly cycles through the characters shown. If you want to enter two characters in succession that are both on the same button (for example a P and an R), press  to advance the cursor one space manually between inputting the two characters. *1 lower-case: ÿ; upper -case: ß Set Thumbnail You can change the thumbnail picture that appears in the Disc Navigator for a title to any frame that appears in that title. 1 Highlight the title you want to change the thumbnail picture for. 2 Select ‘Edit’ > ‘Set Thumbnail’ from the command menu panel. The thumbnail setting screen appears from which you can find the frame you want. Input Title Name CAPS small OK Clear Space A B C D E F G H I J K L M . , ? ! N O P Q R S T U V W X Y Z ( ) : ; A A A A A A Æ ç E E E E I I I I # 2 3 ´ µ ¶ · 1 ¿ ` D N O O O O O ø U U U U Y ß $ % 0 1 2 3 4 5 6 7 8 9 < = > _ & £ \ § ¨ © ¬ – ® _ ˚ – / @ [ ¥ ] ˆ ÷ x ± { | } ~ ¡ c a – o – << << 1 / 4 1 / 2 3 / 4 ¸ 12:30 Wed 4/01 Pr 1 SP Key Characters Key Characters 1 . , ’ ? ! – & 1 6 m n o 6 ö ô ò ó ø ñ 2 a b c 2 ä à á â ã æ ç 7 p q r s 7 $ ÿ/ß *1 3 d e f 3 è é ë ê 8 t u v 8 ü ù û ú 4 g h i 4 î ï ì í ¡ 9 w x y z 9 5 j k l 5 £ 0 0  [cursor back]  [cursor for ward] /  [change case] CLEAR [clear character]  <space>  [finish name input] VIDEO Plus (SHIFT MENU) ~ ( ) _ / : ; ” ` ^ @ # ∗ % ¥ | = { } [ ] < > HDD Video mode VR mode Disc Navigator (HDD) 4 Titles Remain HDD SP All Genres 10Titles 30h30m Recent First 11/29 MON 7:00PM 11/29Mon 7:00PM 2ch SP 2h00m(1.0G) 1 20:00 FRI 3/12 20:00 Fri 3/12 Pr 9 SP 2h00m(1.0G) 22:00 THU 2/12 22:00 Thu 2/12 Pr 7 SP 1h00m(1.0G) 19:00 MON 29/11 19:00 Mon 29/11 Pr 2 SP 1h00m(1.0G) 23:00 FRI 3/12 23:00 Fri 3/12 Pr 4 SP 2h00m(1.0G) 9 8 7 10 Play Erase Edit Multi-Mode Genre Name Cancel T itle name Erase Section Divide Cancel Set Thumbnail Set Genre Lock Chapter Edit 09 Editing.fm 76 ページ ２００５年３月１日　火曜日　午後５時２７分
Editing 08 77 En 3 Use the playback controls (  ,  ,  ,  , etc.) to find a suitable frame, then press ENTER to set. You can also use the CM SKIP ( SHIFT  ) buttons. 4 Select ‘Exit’ to return to the Edit screen. Erase Section Using this command you can delete a part of a title, ideal for cutting out the commercial breaks in a recording made from the TV. 1 Highlight the title containing the section you want to erase. 2 Select ‘Edit’ > ‘Erase Section’ from the command menu panel. 3 HDD only: Select the type of edit. • Video Mode Compatible Editing – Edit points cannot be set with absolute precision, but high- speed copying to Video mode DVD will be possible. • Frame Accurate Editing – Exact edit points are preserved, but high-speed copying to Video mode DVD will not be possible. • For more information about these options, see Editing accuracy on page 74 4 Highlight ‘From’ then use the playback controls (  ,  ,  ,  , etc.) to find the start of the section to erase, then press ENTER. The bar at the bottom of the screen indicates the current play position in the title. After pressing ENTER , a marker shows the start of the section. 5 Highlight ‘To’ then, in the same way, find the end of the section to erase, then press ENTER. After pressing ENTER , another marker indicates the end of the section, with the section itself marked in red. 6 Select ‘Yes’ to confirm, or ‘No’ to cancel, then press ENTER. In the thumbnail viewer you can see a few seconds of video either side of the marked section to see how the edit will look. • When editing VR mode Original content, you may not be able to erase very short sections (less than five seconds). Divide Play List only Use this command to divide a title into two. Note that once divided, the two new HDD titles cannot be recombined into one again. 1 Highlight the title you want to divide. 2 Select ‘Edit’ > ‘Divide’ from the command menu panel. 3 HDD only: Select the type of edit. • Video Mode Compatible Editing – Edit points cannot be set with absolute precision, but high- speed copying to Video mode DVD will be possible. Set Thumbnail (HDD)  Play Pause Rec. time 0h01m 5-1 19:00 Mon 29/11 Pr 2 SP 00.00.09.15 Exit OK Exit OK HDD VR mode ! Video Mode Compatible Editing Frame Accurate Editing DVD RECORDER Please select the type of editing. Video Mode Compatible Editing is recommended for compatibility with high-speed copying. Erase Section (HDD)  Play Pause Rec. time 0h01m 5-1 18:00 Mon 29/11 Pr 1 XP Exit From To 00.00.09.15 HDD VR mode ! Video Mode Compatible Editing Frame Accurate Editing DVD RECORDER Please select the type of editing. Video Mode Compatible Editing is recommended for compatibility with high-speed copying. DVR-433H_UK.book 77 ページ ２００５年３月１日　火曜日　午後５時６分
Editing 08 78 En • Frame Accurate Editing – Exact edit points are preserved, but high-speed copying to Video mode DVD will not be possible. • For more information about these options, see Editing accuracy on page 74 4 Use the playback controls (  ,  ,  ,  , etc.) to find the place you want to divide the title. 5 Press ENTER to divide the title at the current playback position. 6 Select ‘Yes’ to confirm you want to divide the title, or ‘No’ to cancel. Chapter Edit When editing a VR mode DVD or video on the HDD you can edit individual chapters within a title, with commands for erasing, combining and dividing. 1 Highlight the title that contains the chapters you want to edit. 2 Select ‘Edit’ > ‘Chapter Edit’ from the command menu panel. 3 HDD only: Select the type of edit. • Video Mode Compatible Editing – Edit points cannot be set with absolute precision, but high- speed copying to Video mode DVD will be possible. • Frame Accurate Editing – Exact edit points are preserved, but high-speed copying to Video mode DVD will not be possible. • For more information about these options, see Editing accuracy on page 74 4 Select the command you want: • Divide – Divide a chapter into two or more parts: Use the playback controls (  ,  ,  ,  , etc.) to find the point at which you want to divide the chapter, then press ENTER . You can keep dividing the chapter as many times as you wish (up to 999 chapters per DVD disc or 99 chapters per HDD title). • Erase 1 /Move 2 – Erase or move chapters: Select the chapter you want to erase/move and press ENTER . Select whether you want to erase or move the chapter. Move command only: Select the destination for the chapter, and press ENTER . • Combine 3 – Combine two adjacent chapters into one: Highlight the bar divider between two adjacent chapters and press ENTER . 5 Select ‘Exit’ to get back to the main Disc Navigator screen. Divide Title (HDD)  Play Pause Rec. time 0h01m 5–1 18:00 Mon 29/11 Pr 1 XP Cancel 00.00.09.15 Divide Yes Divided titles cannot be combined. OK? No ! HDD VR mode ! Video Mode Compatible Editing Frame Accurate Editing DVD RECORDER Please select the type of editing. Video Mode Compatible Editing is recommended for compatibility with high-speed copying. Note 1. When editing VR mode Original content, it may not be possible to erase chapters less than five seconds long. 2. VR mode Play List only. 3. It may not always be possible to combine two chapters, even though they are adjacent. If a chapter has been divided into three, then the middle chapter erased, it is not possible to combine the two remaining chapters into one. Chapter Edit (DVD VR mode Play List) Rec. time 1–1  Play 0.00.00 19:00 Mon 29/11 Pr 2 SP 1h00m Chapters 5 Exit Erase/Move Combine Divide Chapter Edit (DVD VR mode Play List) 002 003 005 004 001 Rec. time Chapter 1h00m 0h01m 19:00 Mon 29/11 Pr 2 SP Exit Erase/Move Combine Divide Move Cancel Erase Chapter Edit (DVD VR mode Play List) 002 003 005 004 001 Rec. time 19:00 Mon 29/11 Pr 2 SP 1h00m Exit Erase/Move Divide Combine DVR-433H_UK.book 78 ページ ２００５年３月１日　火曜日　午後５時６分
Editing 08 79 En Set Genre Use this command to assign a genre to a title. 1 Highlight the title you want to assign a genre to. 2 Select ‘Edit’ > ‘Set Genre’ from the command menu panel. 3 Use the / buttons to select a genre for the title, then press ENTER. Lock Original only You can lock a title so that it can’t be edited or erased accidently. If you do need to edit it, you can always unlock it later. Important • You can’t undo any edits made before changing the lock status. You also can’t undo a lock/unlock command using the Undo option from the Disc Navigator menu. 1 Highlight the title you want to lock (or unlock). 2 Select ‘Edit’ > ‘Lock’ from the command menu panel. An unlocked title will become locked; a locked title will be unlocked. Locked titles are shown in the Disc Navigator with a padlock icon. Move Play List only Use this function to re-arrange the playing order of Play List titles. 1 Highlight the title you want to move. 2 Select ‘Edit’ > ‘Move’ from the command menu panel. 3 Select a new position in the Play List for the title, then press ENTER. After pressing ENTER , the new, updated Play List is displayed. HDD Disc Navigator (HDD) 11/29 MON 7:00PM 11/29Mon 7:00PM 2ch SP 2h00m(1.0G) 1 4 Titles Remain HDD SP All Genres 10Titles 30h30m Recent First 9 8 7 10 20:00 FRI 3/12 20:00 Fri 3/12 Pr 9 SP 2h00m(1.0G) 22:00 THU 2/12 22:00 Thu 2/12 Pr 7 SP 1h00m(1.0G) 19:00 MON 29/11 19:00 Mon 29/11 Pr 2 SP 1h00m(1.0G) 23:00 FRI 3/12 23:00 Fri 3/12 Pr 4 SP 2h00m(1.0G) Play Erase Edit Multi-Mode Genre Name Cancel T itle name Erase Section Divide Cancel Set Thumbnail Set Genre Lock Chapter Edit Disc Navigator (HDD) 11/29 MON 7:00PM 11/29Mon 7:00PM 2ch SP 2h00m(1.0G) 1 4 Titles Remain HDD SP All Genres 10Titles 30h30m Recent First 9 8 7 10 20:00 FRI 3/12 20:00 Fri 3/12 Pr 9 SP 2h00m(1.0G) 22:00 THU 2/12 22:00 Thu 2/12 Pr 7 SP 1h00m(1.0G) 19:00 MON 29/11 19:00 Mon 29/11 Pr 2 SP 1h00m(1.0G) 23:00 FRI 3/12 23:00 Fri 3/12 Pr 4 SP 2h00m(1.0G) Play Erase Edit Multi-Mode Genre Name Cancel T itle name Erase Section Edit Chapter Cancel Set Thumbnail Set Genre Lock Divide Free4 Free1 Free5 Cancel Free3 No Category Free2 HDD Video mode VR mode Disc Navigator (HDD) 11/29 MON 7:00PM 11/29Mon 7:00PM 2ch SP 2h00m(1.0G) 1 4 Titles Remain HDD SP All Genres 10Titles 30h30m Recent First 9 8 7 10 20:00 FRI 3/12 20:00 Fri 3/12 Pr 9 SP 2h00m(1.0G) 22:00 THU 2/12 22:00 Thu 2/12 Pr 7 SP 1h00m(1.0G) 19:00 MON 29/11 19:00 Mon 29/11 Pr 2 SP 1h00m(1.0G) 23:00 FRI 3/12 23:00 Fri 3/12 Pr 4 SP 2h00m(1.0G) Play Erase Edit Multi-Mode Genre Name Cancel T itle name Erase Section Divide Cancel Set Thumbnail Set Genre Lock Chapter Edit VR mode Disc Navigator (DVD) 4 Titles Remain 10Titles 0h30m 11/29 MON 7:00PM 11/29Mon 7:00PM 2ch SP 2h00m(1.0G) 12/2 THU 10:00PM 12/2Thu 10:00PM 7ch SP 2h00m(1.0G) 12/3 FRI 8:00PM 12/3Fri 8:00PM 9ch SP 1h00m(1.0G) 12/3 FRI 11:00PM 12/3Fri 11:00PM 9ch SP 1h00m(1.0G) 1 2 3 4 DVD VR Mode Play List 11/29 MON 7:00PM 11/29Mon 7:00PM 2ch SP 2h00m(1.0G) 1 Play Erase Edit Multi-Mode Genre Name Cancel T itle name Erase Section Divide Cancel Set Thumbnail Move Combine Chapter Edit Disc Navigator (DVD) 4 Titles Remain 10Titles 0h30m Play List 11/29 MON 7:00PM 11/29Mon 7:00PM 2ch SP 2h00m(1.0G) 1 20:00 FRI 3/12 20:00 Fri 3/12 Pr 9 SP 2h00m(1.0G) 22:00 THU 2/12 22:00 Thu 2/12 Pr 7 SP 1h00m(1.0G) 19:00 MON 29/11 19:00 Mon 29/11 Pr 2 SP 1h00m(1.0G) 23:00 FRI 3/12 23:00 Fri 3/12 Pr 4 SP 2h00m(1.0G) 2 1 3 4 DVD VR Mode DVR-433H_UK.book 79 ページ ２００５年３月１日　火曜日　午後５時６分
Editing 08 80 En Combine Play List only Use this function to combine two Play List titles into one. 1 Highlight the title you want to combine. This title will remain in the same place after combining with another title. 2 Select ‘Edit’ > ‘Combine’ from the command menu panel. 3 Select another title to combine with the first. This title will be appended to the first title selected. After pressing ENTER , the new, updated Play List is displayed. Genre Name Use this command to rename one of the five user- definable genres ( Free 1 – 5 ). 1 Select ‘Genre Name’ from the command menu panel. 2 Use the / buttons to select one of the user- definable genre names, then press ENTER. 3 Input a name for the genre. • The name can be up to 12 characters long. • For information on remote control key shortcuts, see Using the remote key shortcuts to input a name on page 76. 4 To finish entering the name, highlight ‘OK’ and press ENTER. Multi-Mode Multi-Mode allows you to select several titles, then select a command that will be applied to all of them. In this way you can select multiple titles and then erase them all at once, for example. 1 Select ‘Multi-Mode’ from the command menu panel. 2 Select titles from the title list. Use the / and ENTER buttons to select. Selected titles are marked with a  . VR mode Disc Navigator (DVD) 4 Titles Remain 10Titles 0h30m DVD VR Mode Play List 11/29 MON 7:00PM 11/29Mon 7:00PM 2ch SP 2h00m(1.0G) 1 20:00 FRI 3/12 20:00 Fri 3/12 Pr 9 SP 2h00m(1.0G) 22:00 THU 2/12 22:00 Thu 2/12 Pr 7 SP 1h00m(1.0G) 19:00 MON 29/11 19:00 Mon 29/11 Pr 2 SP 1h00m(1.0G) 23:00 FRI 3/12 23:00 Fri 3/12 Pr 4 SP 2h00m(1.0G) 2 1 3 4 Play Erase Edit Multi-Mode Genre Name Cancel T itle name Erase Section Divide Cancel Set Thumbnail Move Combine Chapter Edit Disc Navigator (DVD) 4 Titles Remain 10Titles 0h30m DVD VR Mode Play List 11/29Mon 7:00PM 2ch SP 1 20:00 FRI 3/12 20:00 Fri 3/12 Pr 9 SP 2h00m(1.0G) 22:00 THU 2/12 22:00 Thu 2/12 Pr 7 SP 1h00m(1.0G) 19:00 MON 29/11 19:00 Mon 29/11 Pr 2 SP 1h00m(1.0G) 23:00 FRI 3/12 23:00 Fri 3/12 Pr 4 SP 2h00m(1.0G) 2 1 3 4 HDD Disc Navigator (HDD) 4 Titles Remain HDD SP All Genres 10Titles 30h30m Recent First 11/29 MON 7:00PM 11/29Mon 7:00PM 2ch SP 2h00m(1.0G) 1 20:00 FRI 3/12 20:00 Fri 3/12 Pr 9 SP 2h00m(1.0G) 22:00 THU 2/12 22:00 Thu 2/12 Pr 7 SP Multi-Mode 0G) 19:00 MON 29/11 19:00 Mon 29/11 Pr 2 SP 1h00m(1.0G) 23:00 FRI 3/12 23:00 Fri 3/12 Pr 4 SP 2h00m(1.0G) 9 8 7 10 Play Erase Edit Genre Name Multi-Mode Disc Navigator (HDD) 4 Titles Remain HDD SP All Genres 10Titles 30h30m Recent First 11/29 MON 7:00PM 11/29Mon 7:00PM 2ch SP 2h00m(1.0G) 1 20:00 FRI 3/12 20:00 Fri 3/12 Pr 9 SP 2h00m(1.0G) 22:00 THU 2/12 22:00 Thu 2/12 Pr 7 SP 1h00m(1.0G) 19:00 MON 29/11 19:00 Mon 29/11 Pr 2 SP 1h00m(1.0G) 23:00 FRI 3/12 23:00 Fri 3/12 Pr 4 SP 2h00m(1.0G) 9 8 7 10 Play Erase Edit Multi-Mode Genre Name Cancel Free1 Free2 Free3 Free4 Free5 Cancel Input Genre Name CAPS small OK Clear Space Free 1 A B C D E F G H I J K L M . , ? ! N O P Q R S T U V W X Y Z ( ) : ; A A A A A A Æ ç E E E E I I I I # 2 3 ´ µ ¶ · 1 ¿ ` D N O O O O O ø U U U U Y ß $ % 0 1 2 3 4 5 6 7 8 9 < = > _ & £ \ § ¨ © ¬ – ® _ ˚ – / @ [ ¥ ] ˆ ÷ x ± { | } ~ ¡ c a – o – << << 1 / 4 1 / 2 3 / 4 ¸ HDD Disc Navigator (HDD) 4 Titles Remain HDD SP All Genres 10Titles 30h30m Recent First 11/29 MON 7:00PM 11/29Mon 7:00PM 2ch SP 2h00m(1.0G) 1 20:00 FRI 3/12 20:00 Fri 3/12 Pr 9 SP 2h00m(1.0G) 22:00 THU 2/12 22:00 Thu 2/12 Pr 7 SP 1h00m(1.0G) 19:00 MON 29/11 19:00 Mon 29/11 Pr 2 SP 1h00m(1.0G) 23:00 FRI 3/12 23:00 Fri 3/12 Pr 4 SP 2h00m(1.0G) 9 8 7 10 Play Erase Edit Genre Name Multi-Mode DVR-433H_UK.book 80 ページ ２００５年３月１日　火曜日　午後５時６分
Editing 08 81 En 3 Select ‘Next’ from the command menu panel. 4 Select the command that you want applied to all the marked titles. For example, select Erase to erase all the marked titles. Once the command is completed, Multi-Mode is automatically exited. Undo If you make a mistake while editing, you can generally undo it. There are three levels of undo (in other words, you can undo the last three edits you made). 1 Select ‘Undo’ from the command menu panel. • You can’t undo anything after exiting the Disc Navigator screen. Frequently asked questions • Why doesn’t the available recording time increase when I erase titles from a VR mode DVD-R? When you erase titles from a DVD-R, the titles are no longer displayed, but the content remains on the disc. DVD-R is a write-once medium; it can’t be erased or rewritten. •I can’t edit my disc! You may find that as the available recording time is reduced on a VR mode DVD-R disc, editing is no longer possible. This is because information about your edits requires a certain amount of disc space. As you edit, this information builds up, eventually preventing you from editing further. Disc Navigator (HDD) 4 Titles Remain HDD SP All Genres 10Titles 30h30m Recent First 2h00m(1.0G) 20:00 FRI 3/12 20:00 Fri 3/12 Pr 9 SP 2h00m(1.0G) 22:00 THU 2/12 22:00 Thu 2/12 Pr 7 SP 1h00m(1.0G) 19:00 MON 29/11 19:00 Mon 29/11 Pr 2 SP 1h00m(1.0G) 23:00 FRI 3/12 23:00 Fri 3/12 Pr 4 SP 9 Next Single Mode Multi-Mode Disc Navigator (HDD) 4 Titles Remain HDD SP All Genres 3Titles 30h30m Recent First 2h00m(1.0G) 2h00m(1.0G) 22:00 THU 2/12 22:00 Thu 2/12 Pr 7 SP 1h00m(1.0G) 19:00 MON 29/11 19:00 Mon 29/11 Pr 2 SP 1h00m(1.0G) 23:00 FRI 3/12 23:00 Fri 3/12 Pr 4 SP 8 7 10 Next Comfirm Cancel Multi-Mode Change Genre Lock Unlock Single Mode Cancel Erase Video mode VR mode Disc Navigator (DVD) 11/29 MON 7:00PM 11/29Mon 7:00PM 2ch SP 2h00m(1.0G) 2h00m(1.0G) 1h00m(1.0G) 1 4 Titles Remain 10Titles 0h30m DVD VR Mode 2h00m(1.0G) Play List Play Erase Edit Create Undo No title DVR-433H_UK.book 81 ページ ２００５年３月１日　火曜日　午後５時６分
Using the Jukebox 09 82 En Chapter 9 Using the Jukebox The Jukebox feature allows you to use the recorder’s HDD to store and playback music from up to 999 of your CDs. Once on the HDD, you can name albums, assign them a genre, and set tracks that you don’t want to play to Jump. Copying CDs to the HDD The first step is to copy some CDs to your HDD. This is done in real-time. All tracks are copied from each CD 1 as an album. Although album and track names are not copied, you can add these later (see Editing Jukebox albums on page 83). Usually, the tracks are copied to the HDD in the order they appear on the CD. If you want to copy them in some other order, set the CD to play in program play mode. See Program play on page 59 for how to do this. Note that once copied to the HDD, audio tracks cannot be recorded back to a DVD-R/RW disc. Important • During copying, no other recorder operation is possible. • Scheduled timer recordings will not start until copying is complete. • Copy protected CDs may not copy successfully. 1 Press HDD/DVD and select DVD. 2 Load the CD you want to copy to the HDD. If you want to copy the CD with a different track order, set the program play mode here. 3 Press  to starts CD playback. 4 Press ONE TOUCH COPY. Alternatively, you can select DVD/CD  HDD from the Copy submenu of the Home Menu. The CD can be playing or stopped when you press ONE TOUCH COPY . If the CD is playing, playback (and copying) will start from the beginning of the CD. Note 1. The recorder can copy up to 999 CDs; a CD can contain up to 99 tracks. The recorded audio format is 256 kbps Dolby Digital. DVD RECORDER STANDBY/ON TOP MENU MENU DISC NAVIGA TOR HOME MENU HDD/DVD TV/DVD DISPLAY RETURN AUDIO HELP CLEAR INPUT SELECT SUBTITLE ANGLE S HOW V IEW CHANNEL SKIP TV DRECT REC ENTER REC MODE ST0P REC REC SHIFT ONE TOUCH COPY BACK CM     DVR-433H_UK.book 82 ページ ２００５年３月１日　火曜日　午後５時６分
Using the Jukebox 09 83 En Playing music from the Jukebox You can select albums or individual tracks from the Jukebox to play. 1 1 Press Home Menu and select ‘Jukebox’. The album list is displayed. 2 Use the / buttons to select the album you want to play and press ENTER . • The album always plays from the first track. Once all tracks on the selected album have played, the next album in the list will play (excluding tracks that have been set to Jump—see Editing Jukebox albums on page 83). Selecting a track from an album to play 1 Use the / buttons to select the album containing the track you want to play, then press  . 2 Use the / buttons to select the track you want to play and press ENTER. • You can play tracks that are set to Jump like this (after the track has played, the next track that doesn't have Jump set will be played). Editing Jukebox albums A number of commands are available for editing and changing the playback behaviour of albums. 1 Use the /// buttons to select the album/ track you want to edit. 2 Press  to display the command menu panel. 3 Use the / buttons to select a menu command and press ENTER. • Erase – Erase the selected track (if all tracks in an album are selected, the whole album is erased). • Edit > Album Name – Enter a name of up to 64 characters for the album. See page Title Name on page 75 for how to enter names. • Edit > Change Genre – Set or change the genre for the album. • Edit > Jump Set 2 – Set a track to jump so that it doesn't play (choose this command again to cancel the Jump setting). • Play Mode – Change the playback order for albums and tracks. • Genre Name – Enter a name of up to 12 characters for a genre. See page Title Name on page 75 for how to enter names. Note 1. The digital audio output contains a copy-prohibit signal when albums are playing from the HDD. T imer Recording Photo Viewer Disc Setup Play Mode Disc Navigator Initial Setup Video/Audio Adjust Copy Juke Box 12/1 1 HDD New First 21:00 FRI 25/03 T otal 12 1.14.58 Repeat Off 10Albums Jukebox 60h30m Remain 9 Album2 8 Album3 7 Album4 6 Album5 5 Album6 4 Album7 3 Album8 10 Album1 All Genres Play Erase Edit Play Mode Genre Name 1-10 0.03.58  ALL 1 2 3 4 5 6 7 Album name Info for selected album Playback status 2. Tracks set to Jump will be skipped during consecutive track playback. 12/1 1 HDD New First Jukebox 60h30m Remain 9 Album2 8 Album3 7 Album4 6 Album5 5 Album6 4 Album7 3 Album8 10 Album1 All Genres Play Erase Edit Play Mode Genre Name 1-10 0.03.58  21:00 FRI 25/03 T otal 12 1.14.58 Repeat Off 10Albums ALL 1 2 3 4 5 6 7 All tracks set to play T rack set to Jump DVR-433H_UK.book 83 ページ ２００５年３月１日　火曜日　午後５時６分
Using the Jukebox 09 84 En Changing the album view 1 From the album list, press  to display the view options menu panel. 2 Select the view option you want, then press ENTER. • Display order New First – Most recently copied CDs appear at the top of the album list. Most Listened – Most often listened to CDs appear at the top of the list. Album Name – Albums are listed alphabetically. Recording Date – Albums are listed by the recording date (oldest first). • Genre All – All albums are displayed. Genre – Only albums in the selected genre are displayed. 12/1 1 HDD New First 21:00 FRI 25/03 T otal 12 1.14.58 Repeat Off 10Albums Jukebox 60h30m Remain 2 Album2 3 Album3 4 Album4 5 Album5 6 Album6 7 Album7 8 Album8 1 Album1 All Genres 1-10 0.03.58  Display order New First Genre All Genres Play Erase Edit Play Mode Genre Name ALL 1 2 3 4 5 6 7 New first Recording Date Most Listened Cancel Album Name 12/1 1 HDD New First 21:00 FRI 25/03 T otal 12 1.14.58 Repeat Off 10Albums Jukebox 60h30m Remain 2 Album2 3 Album3 4 Album4 5 Album5 6 Album6 7 Album7 8 Album8 1 Album1 All Genres 1-10 0.03.58  Display order New First Genre All Genres Play Erase Edit Play Mode Genre Name ALL 1 2 3 4 5 6 7 All Genres No Category Jazz Classical Pops Rock Best DVR-433H_UK.book 84 ページ ２００５年３月１日　火曜日　午後５時６分
The PhotoViewer 10 85 En Chapter 10 The PhotoViewer From the PhotoViewer you can view JPEG photos and picture files stored on a CD-ROM/R/RW 1 on your TV. Playing a slideshow 1 Press HOME MENU and select ‘PhotoViewer’ to display the PhotoViewer screen. • The PhotoViewer is only accessible when a disc containing JPEG files is loaded. • If you encounter a disc that will not play, check that the disc and file formats are compatible with this recorder (see JPEG file compatibility and PC-created disc compatibility on page 10). 2 Use the / buttons to select a folder from the folder list. The first nine images from the selected folder are displayed as thumbnails in the main part of the screen. • The larger the file size, the longer it takes the recorder to load the file. 3 Press ENTER or  to move to the thumbnail view area. The first thumbnail image is highlighted. • To get back to the folder list, press RETURN (or  when the leftmost thumbnail is highlighted). 4 Use the /// to select a thumbnail. • Use the  and  buttons to display the previous/ next page of thumbnails. 5 Press ENTER or  to start playing a slideshow from the selected thumbnail. • Use the  /  buttons to display the previous/ next picture, or the  button to pause the slideshow. • Depending on the aspect ratio, some pictures may be displayed with black bars top and bottom, or left and right. • Large picture files may take a few seconds to display. This is normal. 6 Press  or RETURN to return to the thumbnail view area. 7 To return to the folder view area, press RETURN (or  when the leftmost thumbnail is highlighted). • To exit the PhotoViewer, press HOME MENU . Note 1. Up to 999 files or 99 folders are viewable, but if there are more files/folders than this on the disc it is still possible to view them all using the Reload function (see the following page). PhotoViewer 1/2 1/3 01. 12/12 TUE 02. 12/13 WED 03. 12/14 THU 04. 12/15 FRI 05. 12/16 SAT 06. 12/17 SUN 07. 12/18 MON 08. 12/19 TUE 1 4 7 2 5 8 3 6 9 File Date/Time Chair No. 2 10:00 MON 24/1 1920 x 1440 Currently selected thumbnail Incompatible/unknown file File information Pages in file view Pages in folder list Currently selected folder in folder list DVR-433H_UK.book 85 ページ ２００５年３月１日　火曜日　午後５時６分
The PhotoViewer 10 86 En Reloading files from a disc If you have a disc with a large number of files and/or folders, you can still view all the images using the reload function. 1 Use the  button to navigate to the last entry in the folder list (‘Read next: ...’). 2 Press ENTER to load the next batch of up to 999 files/99 folders from the disc. It will take a moment (at most a minute) to load in the images. 1 Zooming the image During a slideshow you can zoom in to enlarge a portion of the picture by a factor of two or four. You can also move the area of the picture displayed. 1 During a slideshow, use the CHANNEL button to zoom the picture. Repeated presses cycle between zoom off, 2x zoom and 4x zoom. The zoom factor is displayed on-screen. 2 Use the /// to move the zoomed area within the picture. Rotating an image You can rotate the displayed picture during a slideshow so you can always view pictures the right way up, whichever way they were taken. • During a slideshow, press ANGLE (SHIFT 3) to rotate the displayed picture clockwise by 90º. Press ANGLE ( SHIFT 3 ) repeatedly to continue rotating the picture in increments of 90º. Note 1. You can press HOME MENU to exit the PhotoViewer screen while the recorder is reloading images. (If you enter the PhotoViewer again, it will resume reloading.) 2x Zoom   DVR-433H_UK.book 86 ページ ２００５年３月１日　火曜日　午後５時６分
The Disc Setup menu 11 87 En Chapter 11 The Disc Setup menu Introduction From the Disc Setup menu you can name discs, lock the contents to prevent accidental recording and erasure, initialize and finalize discs. The Disc Setup menu is accessed from the Home menu: • Press HOME MENU and select ‘Disc Setup’. Basic settings Input Disc Name When you initialize a disc for recording, the recorder automatically assigns a name for the disc ranging from DISC 1 to DISC 99 . You can use the Input Disc Name function 1 to change the default disc name to something more descriptive. This name appears when you load the disc and when you display disc information on-screen. 1 Select ‘Input Disc Name’ from the Basic options, then ‘Next Screen’. 2 Input a name for the disc up to 64 characters long for a VR mode disc, or 40 for a Video mode disc. • Use the /// and ENTER to select characters. • Use the / buttons to change the cursor position. • Select CAPS or small to change to upper or lower- case, or use the CASE SELECTION buttons ( /  ). • You can also use the CLEAR button to delete characters directly (press and hold for two seconds to delete the whole name). • For discs formatted on a different DVD recorder, you will see only a limited character set. Lock Disc • Default setting: Off Set to On to prevent accidental recording, editing or erasing of the disc loaded 2 . If you need to unlock the disc to make edits, select Off . Important •A locked disc can still be initialized (which will completely erase the disc). Initialize settings You can initialize a recordable DVD disc for either VR mode or Video mode recording. The first time you load a new DVD-RW disc, it will be automatically initialized for recording according to the DVD-RW Auto Init. setting in the Initial Setup menu (see page 97). Note 1. You cannot input a name for a disc if the TV line system of the disc is different to the current setting of the recorder. See Additional information about the TV system settings on page 99 for how to change the recorder’s setting. VR mode Video mode Basic Initialize Finalize Optimize HDD Disc Setup Input Disc Name Lock Disc Basic Input Disc Name Next Screen Input Disc Name Input Disc Name CAPS small OK Clear Space A B C D E F G H I J K L M . , ? ! N O P Q R S T U V W X Y Z ( ) : ; A A A A A A Æ ç E E E E I I I I # 2 3 ´ µ ¶ · 1 ¿ ` D N O O O O O ø U U U U Y ß $ % 0 1 2 3 4 5 6 7 8 9 < = > _ & £ \ § ¨ © ¬ – ® _ ˚ – / @ [ ¥ ] ˆ ÷ x ± { | } ~ ¡ c a – o – << << 1 / 4 1 / 2 3 / 4 ¸ DISC7 2. You cannot change the lock setting for a disc if the TV line system of the disc is different to the current setting of the recorder. See Additional information about the TV system settings on page 99 for how to change the recorder’s setting. VR mode Basic Initialize Finalize Optimize HDD Disc Setup Input Disc Name Lock Disc Basic On Off Lock Disc DVD-R DVD-RW DVR-433H_UK.book 87 ページ ２００５年３月１日　火曜日　午後５時６分
The Disc Setup menu 11 88 En New DVD-R discs are ready for Video mode recording when you load them, but it is also possible to initialize them for VR mode recording. The initialize menu here lets you reinitialize a disc, for example if you want to change the recording format of the disc. See Initializing a recordable DVD disc on page 52 for detailed instructions. Finalize settings 1 Finalize Finalizing ‘fixes’ the recordings in place so that the disc can be played on a regular DVD player or computer equipped with a suitable DVD-ROM drive. See Playing your recordings on other DVD players on page 51 for detailed instructions. Undo Finalize You can undo the finalization on DVD-RW discs recorded on this recorder in Video mode. You need to do this if you want to record more material or edit material already on the disc. You can also undo the finalization of VR mode discs which have been finalized on other DVD recorders. If when you load a disc the message This disc cannot be recorded. Undo the finalization is displayed, use this command to be able to record on the disc using this recorder. 1 From the Disc Setup menu, select ‘Finalize’, then ‘Undo Finalize’ from the finalize options. 2 Select ‘Start’. Optimize HDD You’ll see a message appear on-screen recommending you optimize the HDD. As you record, erase and edit recordings, the HDD file system gradually becomes fragmented. Periodically, the HDD will need optimizing to ‘clean up’ all the fragmented files. Important • Optimizing the HDD can take as long as eight hours. During optimization, playback and recording are not possible. • Canceling optimization mid-way does not undo the optimization already done, so the HDD will be partly optimized. • Select ‘Optimize HDD’ from the disc Setup menu. • Select ‘Start’ to optimize. A progress bar indicates how long there is left to go. Initialize HDD When your DVD recorder is working without a problem this option is not visible in the Disc Setup menu. However, if the HDD file system becomes corrupted for some reason, you initialize the HDD to fix the problem. Note that initializing the HDD will erase all the data on it. • Select ‘Initialize HDD’ from the disc Setup menu. • Select ‘Start’ to initialize. Note 1. You cannot finalize a disc or use the Undo Finalize command if the TV line system of the disc is different to the current setting of the recorder. See Additional information about the TV system settings on page 99 for how to change the recorder’s setting. DVD-R DVD-RW DVD-RW HDD Basic Initialize Finalize Optimize HDD Disc Setup Start Optimization Optimize HDD Start Optimize HDD HDD Basic Initialize Finalize Optimize HDD Disc Setup Initialize Optimize HDD Start Initialize HDD DVR-433H_UK.book 88 ページ ２００５年３月１日　火曜日　午後５時６分
The Video/Audio Adjust menu 12 89 En Chapter 12 The Video/Audio Adjust menu Using the Video/Audio Adjust menu you can set up the picture quality for the built-in tuner and external inputs, for disc playback, and for recording. Setting the picture quality for TV and external inputs Picture Creation lets you choose a set of picture quality settings for the built-in TV tuner and for each external input. There are several preset settings that suit various sources, or you can create up to three of your own sets. Choosing a preset 1 With the recorder stopped, press HOME MENU and select ‘Video/Audio Adjust’. 2 Select ‘Video Adjust’. 3 Use the / buttons to change the preset. • Use the INPUT SELECT button to switch between the built-in TV tuner and the external inputs. • Use the CHANNEL /– buttons to change the channel of the built-in TV tuner. There are six presets available: • Tuner – suitable for general TV broadcasts • VCR – suitable for video cassettes • LDP – suitable for Laserdiscs • Memory1 – user preset 1 • Memory2 – user preset 2 • Memory3 – user preset 3 You can press DISPLAY ( SHIFT HELP ) to see the individual settings for the current preset ( Tuner , VCR or LDP ). 4 Press ENTER to select the preset. Creating your own set There are three user presets in which you can save your own set of picture quality settings. 1 Follow Choosing a preset above and select one of the user presets (Memory 1, 2 or 3). 2 Select ‘Detailed Settings’. 3 Use the / buttons to select the picture quality setting you want to adjust. You can adjust the following settings: 1 • Prog. Motion – Adjusts the motion and still picture quality when video output is set to progressive. • PureCinema – This setting optimizes the picture for film material when the video output is set to progressive. Usually this is best left set to Auto ; try switching to Off if the picture appears unnatural. • YNR – Adjusts the amount of noise reduction (NR) applied to the Y (brightness) component. • CNR – Adjusts the amount of noise reduction (NR) applied to the C (colour) component. • Detail – Adjusts how sharp edges appear. T imer Recording Photo Viewer Disc Setup Play Mode Disc Navigator Initial Setup Video/Audio Adjust Copy Jukebox Detailed Settings Pr 1 T uner Note 1. When the DV input is selected, only Prog. Motion and PureCinema settings can be adjusted. Detailed Settings Pr 1 Memory1 Memory1 White Level CNR YNR Motion Still Detail PureCinma Prog. Motion White AGC Auto1 Off Max Max Off Off Min Max Max Min Pr 1 DVR-433H_UK.book 89 ページ ２００５年３月１日　火曜日　午後５時６分
The Video/Audio Adjust menu 12 90 En • White AGC – Turn on for automatic white level adjustment. 1 • White Level – Adjusts the intensity of white. • Black Level – Adjusts the intensity of black. • Black Setup – Corrects the standard reference black level (NTSC video input only). • Gamma Correction – Adjusts the brightness of darker images. • Hue – Adjusts overall balance between red and green. • Chroma Level – Adjusts how rich the colours appear. 4 Use the / buttons to adjust the currently selected picture quality setting. 5 When you have all the settings as you want them, press HOME MENU to exit. You can now use the preset for any other input or the built-in TV tuner. Tip • To see more of the picture as you adjust different settings, press ENTER after selecting the setting you want to adjust. Setting the picture quality for disc playback This setting determines how the picture will look when playing discs. Choosing a preset 1 With a disc playing (or paused), press HOME MENU and select ‘Video/Audio Adjust’. 2 Select ‘Video Adjust’ 3 Use the / buttons to change the setting. There are six presets available: • TV(CRT) – suitable for standard cathode-ray tube TVs • PDP – suitable for plasma display screens • Professional – suitable for professional monitors • Memory1 – user preset 1 • Memory2 – user preset 2 • Memory3 – user preset 3 You can press DISPLAY ( SHIFT HELP ) to see the individual settings for the current preset ( TV(CRT) , PDP or Professional ). 4 Press ENTER to select the preset. Creating your own set There are three user presets in which you can save your own set of picture quality settings for disc playback. 1 Follow Choosing a preset above and select one of the user presets (Memory 1, 2 or 3). 2 Move the cursor down and select ‘Detailed Settings’. 3 Select the picture quality setting you want to adjust. You can adjust the following settings: • Prog. Motion – Adjusts the motion and still picture quality when video output is set to progressive. • PureCinema – This setting optimizes the picture for film material when the video output is set to progressive. Usually this is best left set to Auto 1 ; try switching to Auto 2 , On or Off if the picture appears unnatural. • YNR – Adjusts the amount of noise reduction (NR) applied to the Y (brightness) component. • BNR – Adjusts the amount of noise reduction (NR) applied to the block noise (artefacts visible in areas of flat colour, caused by MPEG compression). • Detail – Adjusts how sharp edges appear. • White Level – Adjusts the intensity of white. Note 1. When White AGC is On , the White Level setting can’t be adjusted. Detailed Settings TV(CRT) Detailed Settings Memory1 Memory1 YNR Detail BNR Motion Still Off Max White Level PureCinma Prog. Motion Black Level Auto1 Max Max Off Off Min Max Max Min DVR-433H_UK.book 90 ページ ２００５年３月１日　火曜日　午後５時６分
The Video/Audio Adjust menu 12 91 En • Black Level – Adjusts the intensity of black. • Black Setup – Corrects the standard reference black level (NTSC video playback only). • Gamma Correction – Adjusts the brightness of darker images. • Hue – Adjusts overall balance between red and green. • Chroma Level – Adjusts how rich the colours appear. 4 Use the / buttons to adjust the currently selected picture quality setting. 5 When you have all the settings as you want them, press HOME MENU to exit. Tip • To see more of the picture as you adjust different settings, press ENTER after selecting the setting you want to adjust. Audio DRC • Default setting: Off When watching Dolby Digital material at low volume, it’s easy to lose low level sounds completely—including some of the dialog. Switching on Audio DRC (Dynamic Range Control) can help by bringing up the low level sounds, while controlling high level peaks. 1 During playback or when paused, press HOME MENU and select ‘Video/Audio Adjust’. 2 Select ‘Audio Adjust’. 3 Use the / buttons to adjust DRC from ‘Off‘ to ‘Max’. Exactly how much difference you can hear between the settings will depend on the material. Tip • Audio DRC is not effective when listening to a disc via the digital output when Dolby Digital Out is set to Dolby Digital . In this case adjust the dynamic range from your AV amplifier/receiver. Audio DRC Max Off Audio DRC DVR-433H_UK.book 91 ページ ２００５年３月１日　火曜日　午後５時６分
The Initial Setup menu 13 92 En Chapter 13 The Initial Setup menu Using the Initial Setup menu The Initial Setup menu is where you can set various recorder options for sound, picture, language and so on. Some settings can only be changed when the recorder is stopped. During playback and recording these settings are grayed out in the Initial Setup menu. Except for the Setup Navigator, menu screens are exited automatically after 20 minutes of inactivity. • Press HOME MENU and select ‘Initial Setup’. In the table below, the default option is marked with a •. Setting Options Explanation Basic Settings Clock Setting Auto Set the channel that broadcasts a clock signal and the clock will be set automatically . Manual • If there is no channel that broadcasts a clock signal in your area, you can set the time and date manually . The clock must be set in order to use timer recording. Input Line System 525 System Use for NTSC or P AL-60 recording from an external input. 625 System • Use for standard P AL or SECAM recording. See also About the input line system on page 99 for more information on this setting. Power Save Mode 1 Only signals arriving at the antenna input are passed through to the antenna output when the recorder is in standby . Mode 2 No input signals are passed through to the outputs when the recorder is in standby . Off • When the recorder is in standby , all signals arriving at the SCART and antenna inputs are passed along to the outputs. Help Setting On • Switches on the automatic Help screens for GUI displays. Off Switches off the automatic Help screens for GUI displays. (P ress HELP on the remote to manually display the Help screen.) Setup Navigator Start Select to start the Setup Navigator . See also Switching on and setting up on page 25 . DVR-433H_UK.book 92 ページ ２００５年３月１日　火曜日　午後５時６分
The Initial Setup menu 13 93 En T uner Settings Auto Channel Setting Auto Scan Select your countr y and then wait for the recorder to auto tune into channels in your area. After auto scan has finished, the channel map- ping screen appears showing which channels have been assigned to which program numbers. Y ou can skip unwanted channels using the Manual Channel Setting option below . P ress HOME MENU to exit the channel mapping screen. Download from TV If your TV supports this feature you can download all the channels that your TV is tuned to via the SCART input. Select your countr y and then wait for the download to complete. After the download is complete, the channel mapping screen appears, as above. See also the operating instructions that came with your TV for more information. Manual CH Setting Next Screen P roceed to the next screen if you need to adjust any of the settings made by auto tuning. Select your countr y , then proceed to the manual channel setting screen: • Change channel presets using the CHANNEL /– buttons. • T o skip the displayed channel (because there is no station assigned to that channel), change the Skip setting to On . • Set the CH SYSTEM setting to match the channel system of your countr y or region. • Set the CHANNEL setting to the channel you want to assign to the current channel preset. • T o manually fine tune the channel, change the AFT setting to Off then adjust the Level setting. • The Name field allows you to input a name of up to five characters for the current channel preset. • If the currently selected channel is scrambled requiring a decoder connected to the AV2/AUTO START REC (INPUT 1/DECODER) , set the Decoder setting to On . Channel Swapping Next Screen P roceed to the next screen to swap channel assignments of different presets so that you can group together presets that naturally go together . Select two presets to swap then press ENTER . Set VIDEO Plus CH Next Screen P roceed to the next screen to assign channel numbers to the guide channels as necessar y . Look in your TV guide to see which channel numbers should be assigned to which guide channels. P ress ENTER when your done to leave this screen. Video In/Out Settings Input Colour System Next Screen P roceed to the next screen to set the input colour system for each channel preset. Use the CHANNEL /– buttons to change the preset. On the default Auto setting the recorder can generally correctly detect whether the input signal is P AL, SECAM, 3.58 NTSC or P AL -60, but in some cases you may have to set it manually if the picture is displayed incorrectly . See also About the input colour system on page 99 for more information on this setting. Setting Options Explanation DVR-433H_UK.book 93 ページ ２００５年３月１日　火曜日　午後５時６分
The Initial Setup menu 13 94 En Component Video Out Interlace • Select if your monitor/TV is not compatible with progressive-scan video. Progressive Select if your monitor/TV is progressive-scan compatible. Check the operating instructions that came with your monitor/TV if you’re not sure. For Component Video Out to be effective, the AV1 Out setting (see below) must be set to something other than RGB . A V1 Out Video • Sets the AV1(RGB)-TV SCART output to standard composite video (compatible with all TVs). S-Video Sets the AV1(RGB)-TV SCART output to S-video . Recommended if you are using a long SCART cable. RGB Sets the AV1(RGB)-TV SCART output to RGB. Good quality but check your TV for compatibility . If you choose a setting that is incompatible with your TV you may not be able to see any picture at all. In this case either switch off and reconnect using the supplied video cable, or reset the recorder (see Resetting the recorder on page 111). The Component Video Out setting (see above) has no effect when AV1 Out is set to RGB . A V2/L1 In Video • Sets the AV2/AUTO START REC (INPUT 1/DECODER) SCART input to standard composite video. S-Video Sets the AV2/AUTO START REC (INPUT 1/DECODER) SCART input to S-video. RGB Sets the AV2/AUTO START REC (INPUT 1/DECODER) SCART input to RGB. Decoder Use this setting if you connected a decoder to the AV2/AUTO START REC (INPUT 1/DECODER) SCART connector . For scrambled channels, make sure that the channel Decoder setting is set to On . (See Manual CH Setting on page 93.) NTSC on P AL TV On • NTSC discs will play correctly on P AL-only TVs. Off Use if your TV is already NTSC -compatible. Many recent PAL TVs are compatible with NTSC input and so this setting can be switched off. Check the operating instructions that came with your TV. See also About NTSC on PAL TV on page 99 for related information. Audio In Settings Nicam Select NICAM • Record the NICAM audio in a NICAM broadcast. Regular Audio Record the non-NICAM audio in a NICAM broadcast. (Y ou can still switch the audio to record using the AUDIO ( SHIFT 1 ) button before recording.) T uner Level Normal • Standard setting. Compression Use if the audio level from the built-in tuner is excessive, causing dis- tortion. External Audio Stereo • Select if the audio from the currently selected external input is stan- dard stereo. Bilingual Select if each channel carries a separate soundtrack. When the external audio is from the DV input, an audio subcode channel within the DV audio tells the recorder whether the audio is stereo or bilingual. This has priority over the setting you make here. Setting Options Explanation DVR-433H_UK.book 94 ページ ２００５年３月１日　火曜日　午後５時６分
The Initial Setup menu 13 95 En Bilingual Recording A/L • Record the left (A) channel of a bilingual source when recording to HDD with HDD Recording F ormat set to Video Mode ON, to DVD in Video mode or in LPCM mode, from an external source. B/R As above, but for right (B) channel recording. When recording bilingual audio to DVD in VR mode (except in LPCM mode), or to HDD with HDD Recording Format set to Video Mode Off (except in LPCM mode), both audio channels are recorded and you can switch to the one you want on playback. DV Input Stereo 1 • Select to use the ‘live’ audio track (recorded during the video shoot) from a camcorder that supports two stereo audio tracks. Stereo 2 Select to use the overdubbed audio track from a camcorder that sup- ports two stereo audio tracks. Mix Select one of the three settings to use a mix of the two stereo audio tracks. Input Level (L1–L3) -6dB – 6dB (default: 0 dB) Adjust the input level separately for each of the external inputs from –6dB to 6dB in steps of 3dB. Audio Out Settings Digital Out On • Activates the digital audio output. Off Deactivates the digital audio output. When set to Off , all the following Audio Out settings are grayed out. Dolby Digital Out Dolby Digital • Output a Dolby Digital signal when a Dolby Digital source is being played. Dolby Digital  PCM Convert Dolby Digital sources to Linear PCM output. Use if your con- nected equipment doesn’t have a Dolby Digital decoder . DTS Out On • Output a DTS signal when a DTS source is being played. Off Switch off the digital output when a DTS source is being played. Use when your connected equipment doesn’t have a DTS decoder . In this case, use the analog audio outputs. 96 kHz PCM Out 96 kHz  48 kHz • Convert 96 kHz digital audio sources to 48 kHz output. Use if your con- nected equipment doesn’t support 96 kHz sampling rate. 96 kHz Output 96 kHz digital audio when a 96 kHz source is being played. MPEG Out MPEG Output an MPEG audio signal when a source using MPEG audio is being played. MPEG  PCM • Convert sources with MPEG audio to Linear PCM output. Use if your connected equipment doesn’t have an MPEG audio decoder . Setting Options Explanation DVR-433H_UK.book 95 ページ ２００５年３月１日　火曜日　午後５時６分
The Initial Setup menu 13 96 En Language Settings OSD Language English • Sets the language of the on-screen displays to English. available languages Choose from the languages displayed for the on-screen displays. Audio Language English • Sets the default audio language for DVD-V ideo playback to English. available languages Choose from the languages displayed to set the default audio lan- guage for DVD-V ideo playback. Other Select to set the default audio language to something other than the ones listed. See Selecting other languages for language options on page 100. Discs do not necessarily have audio in your selected language. Also, some discs override the Audio Language preference. Subtitle Language English • Sets the default subtitle language for DVD-V ideo playback to English. available languages Choose from the languages displayed to set the default subtitle lan- guage for DVD-V ideo playback. Other Select to set the default subtitle language to something other than the ones listed. See Selecting other languages for language options on page 100. Discs do not necessarily have subtitles in your selected menu language. Also, some discs override the Subtitle Language preference. Auto Language On • On this setting: • DVD-V ideo discs whose main audio track is in your default language will play using that language, without subtitles. • Discs whose main audio track is not in your default language but that have a subtitle track in your default language will play the original audio track with subtitles. Off Select to play DVD-V ideo discs according to your audio and subtitle language preferences. For Auto Language to be effective, the Audio Language and Subtitle Language options must be set to the same language. DVD Menu Language w/Subtitle Language • Sets the language of DVD-V ideo menus to the same as that set for the subtitle language. English Sets the language of DVD-V ideo menus to English. available languages Choose from the displayed languages to set the default language for DVD-V ideo menus. Other Select to set the DVD menu language to something other than the ones listed. See Selecting other languages for language options on page 100. Discs do not necessarily have menus in your selected menu language. Subtitle Display On • Select to have discs display subtitles according to your Subtitle Lan- guage and Auto Language preferences. Off Select to switch off subtitle display . Assist Subtitle Select to display special additional assistive subtitles, where available. Some discs may override these settings. Setting Options Explanation DVR-433H_UK.book 96 ページ ２００５年３月１日　火曜日　午後５時６分
The Initial Setup menu 13 97 En Recording Settings Manual Recording On (go to setup) All the standard recording modes, plus MN1 – 32 , LPCM and XP modes can be set. Off • Just the standard recording modes ( XP , SP , LP , EP , SLP and SEP ) can be set. See also Manual recording modes on page 107 for detailed information on manual recording levels. Optimized Rec On The recording quality of timer recordings is automatically adjusted to fit on to the selected media if it will not fit at the selected quality set- ting. If the recording will not fit even at MN1 , then the recording will start at MN1 and stop when all the available space is used up. Off • When a timer recording is set that won’t fit on to the selected media, the recording starts but is cut off when no more recording is possible. Optimized Rec will only compensate for the next scheduled timer recording if more than one is set. It cannot be used together with VPS/PDC. Set Thumbnail 0 seconds • Sets the default thumbnail picture in the Disc Navigator to the first frame of the title. 30 seconds Sets the default thumbnail picture to 30 seconds into the title. 3 minutes Sets the default thumbnail picture to 3 minutes into the title. Auto Chapter (Video) No Separation Automatic chapter marking is switched off . 10 minutes • When recording in Video mode, chapter markers are inserted every 10 minutes. 15 minutes Chapter markers are inserted ever y 15 minutes. DVD-RW Auto Init. VR Mode • Blank DVD-RW discs are initialized for VR mode recording when loaded into the recorder for the first time. Video Mode Blank DVD-RW discs are initialized for Video mode recording. HDD Recording Format Video Mode Off R ecordings made to the HDD are made in VR mode. Use this setting if you don’t need to transfer the recording later to a V ideo mode DVD. Video Mode On • Recordings made to the HDD are compatible with V ideo mode record- ings. This setting is convenient if you want to transfer the recording to a Video mode DVD as high-speed copy can be used. When Video Mode On is used, you must select the audio channel you want to record when recording a bilingual broadcast. On the Video Mode Off setting, both channels will be recorded and you can switch between them on playback. See also Bilingual Recording on page 95. Playback Settings TV Screen Size 4:3 (Letter Box) • Select if you have a standard 4:3 TV and prefer the letter box format presentation for widescreen material. 4:3 (Pan & Scan) Select if you have a standard 4:3 TV and prefer the pan and scan pre- sentation for widescreen material. 16:9 Select if you have a widescreen 16:9 TV . Y our TV settings determine how 4:3 material will look. Selecting 4:3 (Letter Box) or 4:3 (Pan & Scan) does not guarantee that all video material will be presented in that format as some discs override this setting. Setting Options Explanation DVR-433H_UK.book 97 ページ ２００５年３月１日　火曜日　午後５時６分
The Initial Setup menu 13 98 En Still Picture Field P roduces a stable, generally shake-free image. Frame P roduces a sharper image, but more prone to shake than Field stills. Auto • The recorder automatically selects Field or F rame type still, according to the material playing. Seamless Playback On Playback is smooth, but with a trade-off against the accuracy of the edit points. Off • Y ou may notice momentar y interruption at edited points during play- back of a VR mode Play List. Parental Lock Set Password In order to change the parental lock level or change the countr y/area code, set the password using this option. F rom the following screen, enter a four-digit number that will be your password. Change Password In order to change the password, first enter your existing password and then a new one from the following screen. Change Level F rom the following screen, first enter your password and then set a parental lock level. Country/Area Code F rom the following screen, first enter your password and then set a countr y/area code. Only certain discs have parental lock and country code features. Check the disc packaging to see what features the disc has. If you forget your password you can reset it by resetting the recorder to its factory settings. See Resetting the recorder on page 111. Angle Indicator On • A camera icon appears on-screen during multi-angle scenes on a DVD-V ideo disc. Off Nothing is indicated on-screen when a multi-angle scene is showing. Options On-Screen Display On • The recorder displays operation displays ( Stop , Play , etc.) on-screen. Off Switches off the on-screen operation displays. Front Panel Display On • The time is shown in the front panel display when the recorder is in standby . Off The front panel display is switched off in standby (although it still lights dimly when setting a timer recording). Remote Control Mode Recorder 1–3 (default: Recorder 1) If you are using more than one recorder in the same room, set them to different IDs. This setting sets the recorder ID; to change the remote controller ID, press and hold RETURN then press 1 , 2 or 3 to set. The remote will only control a recorder with the same ID. AV . Link This Recorder Only • Signals received through the A V input when the recorder is in standby are not passed through to the A V output. Pass Through Signals received when in standby are passed though to the output for connected devices. (Note that during EPG data download, the EPG data is not passed through.) When set to Pass Through , make sure to set Power Save (page 92) to Off . Setting Options Explanation DVR-433H_UK.book 98 ページ ２００５年３月１日　火曜日　午後５時６分
The Initial Setup menu 13 99 En Additional information about the TV system settings About the input line system This recorder is compatible with PAL, SECAM, 3.58 NTSC and PAL-60 TV systems. The Input Line System and Input Colour System settings determine how the recorder treats incoming video signals from an external input or the built-in TV tuner. Please note the following points when changing the input line system: • When the current input is a built-in tuner channel preset, changing the input line system will usually also affect the input line system of the AV2/AUTO START REC (INPUT 1/DECODER) input. However if the AV2/L1 In setting is set to Decoder , then the L2 input is affected instead. • If, when the Input Line System setting is changed, the screen goes blank (due to incompatibility with your TV), you can switch back by pressing and holding the front panel  button then pressing  OPEN/CLOSE (front panel) while the recorder is stopped. • When you switch the Input Line System setting the Copy List is erased. If you switch the setting using the  button and  OPEN/CLOSE buttons as described above, there is no confirmation, so please use with care. • You can’t mix recordings of different TV line systems on the same disc. • When you change this setting, the Input Colour System setting also changes (see below). About NTSC on PAL TV Depending on the Input Line System setting and the NTSC on PAL TV setting, the signal format output when the recorder is stopped varies as shown in the table below. About the input colour system The available options of the Input Colour System setting depend on the Input Line System setting. The table below shows the different options available. Additional information about component video output If you switch the Component Video Out setting to Progressive when using a TV that is not compatible with progressive-scan video, you will not be able to see anything displayed on your TV. If this happens, press and hold the  button on the front panel, then press  . This will set the recorder’s video output back to Interlace. Input Line System NTSC on P AL TV Output when stopped 625 System Off PAL On PAL 525 System Off NTSC On PAL–60 Input Line System Built-in tuner Exter nal input 625 System Auto Auto PAL PAL SECAM SECAM 525 System n/a Auto 3.58 NTSC PAL–60 Compatibility of this unit with progressive-scan TVs Consumers should note that not all high-definition television sets are fully compatible with this product and may cause artifacts to be displayed in the picture. In case of 525 progressive scan picture problems, it is recommended that the user switch the connection to the ‘standard definition’ output ( Interlace ). If there are questions regarding our TV set compatibility with this model, please contact our customer service center. This recorder is compatible with the following Pioneer displays and monitors Plasma display •PDP-503HDE, PDP-433HDE, PDP-434HDE, PDP-504HDE, PDP- 435XDE, PDP-435HDE, PDP-435FDE, PDP-505XDE, PDP- 505HDE, PDP-615EX DVR-433H_UK.book 99 ページ ２００５年３月１日　火曜日　午後５時６分
The Initial Setup menu 13 100 En Selecting other languages for language options 1 Select ‘Other’ from the language list. This option appears in the settings for DVD Menu Language, Audio Language, and Subtitle Language. 2 Select the language you want. • Select by language name: Use the / buttons to change the language. • Select by code number: Press  then use the number buttons to enter the four-digit language code. See Language code list on page 108 for a list of available languages and corresponding codes. 3 Press ENTER to confirm and exit the screen. Basic T uner Video In/Out Audio In Audio Out Language Recording Playback Initial Setup OSD Audio Language Subtitle Language Auto Language DVD Menu Language Subtitle Display DVD Menu Language DVD Menu Language Language Number English 0 5 1 4 Language DVR-433H_UK.book 100 ページ ２００５年３月１日　火曜日　午後５時６分
Additional information 14 101 En Chapter 14 Additional information Screen sizes and disc formats When viewing on a standard TV or monitor Screen format of disc Setting Appearance 16:9 4:3 (Letter Box) The program is shown in widescreen with black bars at the top and bottom of the screen. 4:3 (Pan & Scan) The sides of the program are cropped so that the picture fills the whole screen. 4:3 16:9 The program appears squashed. Set to either 4:3 (Letter Box) or 4:3 (Pan & Scan) . 4:3 (Letter Box) 4:3 (Pan & Scan) The program is presented correctly on either setting. When viewing on a widescreen TV or monitor Screen format of disc Setting Appearance 16:9 16:9 The program is presented in widescreen. 4:3 16:9 Y our TV will determine how the picture is presented—check the manual that came with the TV for details. DVR-433H_UK.book 101 ページ ２００５年３月１日　火曜日　午後５時６分
Additional information 14 102 En Minimum copying times The table below shows the minimum HDD to DVD copying time for one hour of video. Please note that not all discs are compatible with high-speed copying. 1 Check with the disc manufacturer for compatibility. Note that all times in the above table are approximate. *1 Compatible with single speed recording only *2 Compatible with 2x speed recording *3 Compatible with 4x speed recording *4 Compatible with 8x speed recording. *5 Compatible with 12x speed recording. Note that actual copy speed varies with the part of the disc being recorded. The table below shows 16x DVD-R and 6x DVD-RW disc brands that have been tested for high-speed writing compatibility with this recorder. *1 Compatible with 12x speed recording *2 Compatible with 6x speed recording Note 1. There may be cases where even 2x/4x/6x/8x/16x compatible discs do not copy at full speed. High speed copying is not possible when using discs initialized on another recorder. DVD disc type Rec mode DVD-RW V er . 1.0, 1.1 *1 DVD-R V er . 2.0 DVD-RW V er . 1.1/2x *2 DVD-R V er . 2.0/4x *3 DVD-RW V er . 1.2/4x *3 DVD-RW V er . 1.2/6x DVD-R V er . 2.0/8x *4 DVD-R V er . 2.1/8x *4 DVD-R V er . 2.0/16x *5 DVD-R V er . 2.1/16x *5 SEP 6 mins. 3 mins. 1.5 mins. 1.25 mins. 1.1 mins. 1 min. SLP 7.5 mins. 4 mins. 2 mins. 1.5 mins. 1.25 mins. 1.1 mins. EP 10 mins. 5 mins. 2.5 mins. 2 mins. 1.5 mins. 1.25 mins. LP 15 mins. 7.5 mins. 4 mins. 2.5 mins. 2 mins. 1.5 mins. SP 30 mins. 15 mins. 7.5 mins. 5 mins. 4 mins. 3 mins. XP 60 mins. 30 mins. 15 mins. 10 mins. 8 mins. 6 mins. 16x DVD-R *1 6x DVD-RW *2 Maker Manufacturer ID Maker Manufacturer ID Sony That’s TDK Maxell “SONY16D1” “TYG03” “TTH02” “MXL RG04” JVC MCC (MKM) “JVC1Victord7” “MKM01RW6x” DVR-433H_UK.book 102 ページ ２００５年３月１日　火曜日　午後５時６分
Additional information 14 103 En Troubleshooting Incorrect operation is often mistaken for trouble and malfunction. If you think there is something wrong with this component, please check the points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being used. If the trouble cannot be rectified even after checking the points below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work. General Problem Remedy The disc is automatically ejected after closing the disc tray • Check that the disc is not a DVD R/RW , DVD-RAM or other incompatible format disc (page 9). • Check that the disc is loaded properly (aligned in disc tray and label-side up). • T ake out the disc and clean it (page 111). • Check that the disc has a region code compatible with the recorder (page 114). No picture • Check that ever ything is connected properly (page 12). • Check that the connected TV and/or the A V amp/receiver is set to the correct input. • The recorder may be set to progresive scan with an incompatible TV . Reset to interlace by pressing and holding the front panel  button then pressing  . Can’t play a disc • Check that the disc is a compatible format disc (page 9). • T ake out the disc and clean it (page 111). • Check that the disc is loaded properly (aligned in disc tray and label-side up). • There may be condensation in the recorder . Leave the recorder for an hour or so for the condensation to evaporate. • During HDD recording, you can’t play discs that are recorded with a Line System different to the current recorder setting. Can’t r ecord a disc • Check that the disc is not a DVD R/RW , DVD-RAM or other incompatible format disc (page 9). All settings are r eset • If the recorder is unplugged (or there is a power failure) while the recorder is on, all the settings will be lost. • Make sure that you switch the recorder into standby before unplugging the power cord. Remote control does not work • If you connected this recorder to another P ioneer product using the CONTROL IN jack, point the remote control at the other component to use (page 12). • Set the remote control to the same ID number as the recorder (page 98). (When the batteries run down, the remote mode is automatically reset to Recorder1 .) • Use the remote within its operating range (page 8). • Replace the batteries (page 8). No sound or sound is distorted • Make sure that the amp/receiver or TV is set to the correct input and the volume turned up. • There is no sound when the picture is paused, or during scanning or slow motion play . P ress  to resume regular playback. • DTS discs can only be played if this recorder is connected to a DTS decoder or DTS compatible amp/receiver . If you have connected a suitable decoder , also make sure that the Initial Setup > Audio Out > DTS Out setting is On . • Some 96kHz discs do not output audio through the digital jack. In this case, switch the input of your amp/receiver to analog. • Check the audio cable connections (page 12). • If the sound is distorted, tr y cleaning the cable plugs. DVR-433H_UK.book 103 ページ ２００５年３月１日　火曜日　午後５時６分
Additional information 14 104 En The picture fr om the external input is distorted • If the video signal from the external component is copy-protected, you cannot connect via this recorder . Connect the component directly to your TV . The picture is distorted • Change the Input Line System setting (page 99). (Y ou can also change it by pressing the  button and  OPEN/CLOSE on the front panel simultaneously with the recorder stopped.) Screen is str etched vertically or hori- zontally • Make sure that the TV Screen Size setting (page 97) is correct for the kind of TV you have (see also page 101). • If you have a widescreen TV , check its aspect ratio settings. • This recorder ’s input switches into wide mode automatically according to the input signal. When the unit connected is not compatible with VIDEO ID-1 (widescreen signalling), set the connected component to output 4:3 aspect ratio (standard) video. Can’t play a disc r ecorded using this recor der on another player • If the disc was recorded in Video mode, make sure that it’s finalized (page 51). •Some players will not play recordable DVD discs, even when recorded in Video mode and finalized. • If the disc was recorded in VR mode, the other player must be specifically RW compatible in order to play it (page 9). • Discs recorded with copy-once material cannot be played on non- CPRM compatible players (page 38). During playback the picture is dark or distorted • When a copy-protected disc is played via a VCR , the picture will not display correctly . Connect the recorder directly to your TV . Can’t r ecord or does not r ecord suc- cessfully • Check that there is some remaining blank space on the DVD/HDD. • F or a Video mode disc, check that the disc isn ’t already finalized. • The HDD may contain up to 999 titles; one DVD disc 99 (Original) titles and 999 chapters (VR mode), or 99 chapters (Video mode). Check that these limits have not been reached. • Check that the source you are tr ying to record is not copy protected. • F or a VR formatted disc, check that the disc isn’t locked (page 87). • Check that you are recording with the same TV system (P AL, NTSC, etc.) as the disc has already been recorded in. All recordings on a disc must be in the same TV system. When recording to the HDD, it is also necessar y to set the Input Line System setting to match what you want to record (page 99). • The power may have failed during recording. Timer program doesn’ t recor d suc- cessfully • When setting the recording channel, make sure you set the recorder ’s built-in TV tuner , not the TV’s built-in tuner . • When recording to a Video mode disc, programs that are copy-once protected cannot be recorded. Use a VR mode formatted disc for copy-once material (page 38). • T wo timer programs may have overlapped, in which case only the earlier one will record completely . • The power may have failed during recording. After briefly unplugging or after a power failure the fr ont panel dis- play shows ‘--:--’ • A backup batter y inside the recorder keeps the clock and other settings from being reset when there is no power to the recorder . This battery should last approximately five years from factor y shipping. Reset the clock and other recorder settings to use the recorder again . T o have the batter y replaced, contact your dealer or a P ioneer Ser vice Center . Front panel display shows ‘LOCK’ when a button is pressed • The Child Lock is on; turn off in order to use the recorder (page 47). Problem Remedy DVR-433H_UK.book 104 ページ ２００５年３月１日　火曜日　午後５時６分
Additional information 14 105 En If the unit does not operate normally due to external effects such as static electricity, disconnect the power plug from the outlet and insert again to return to normal operating conditions. Frequently asked questions In this section you can find answers to frequently asked questions on how to use your DVD recorder and what it can do. • How do I make a high-quality copy? We recommend that you use the high-speed copy mode. Although the copy is faster than real time, there is no loss of picture or sound quality compared to the original. If there is not enough space on the disc to make a copy at the same picture quality as the original, we recommend that you change the recording mode to ‘Optimized’. This will fit the recording on to the available space on the disc. See also Copying and back-up on page 63. • Can I make a DVD copy of, say, a movie that has had the commercials edited out? Yes. There are two ways to do this. You can either edit the video on the HDD then copy the edited version to DVD, or you can assemble a Copy List that cuts out the commercials, then record that to DVD. See also Copying and back-up on page 63. •I have a two-hour recording on the HDD made in XP mode. Can I copy this to DVD in high-speed mode? A standard DVD disc can hold only an hour of XP mode material, so you wouldn’t be able to make a high-speed copy of this on to one disc. You could divide up the recording on the HDD into two titles of an hour each and copy these to two DVDs (using high-speed copy). Alternatively, you could copy the material in SP (or Optimized) mode so as to fit it all on to one disc (note that there will be a loss in picture quality if you do this). See also Copying and back-up on page 63. • Can I record a bilingual broadcast to the HDD, keeping both audio channels and switch them on playback? Yes. When HDD Recording Format is set to Video Mode Off (see HDD Recording Format on page 97) , both channels of the broadcast are recorded (unless you set the recording mode to LPCM, in which case only the channel set using the Bilingual Recording setting will be recorded; see Using the built-in TV tuner on page 29). • Can I record continuously on the HDD for more than 12 hours? Yes, timer recordings made to the HDD can by set for up to 24 hours . However, because the maximum length of a title is 12 hours, the recording will be spread over two titles. Note that there will be a short break in the recording between titles. See also Setting a timer recording on page 41. • Can I copy a finalized Video mode disc (DVD-R or DVD- RW) to the HDD? Yes. Start playing the Video mode disc and use the One Touch Copy button to copy the currently playing title to the HDD. Repeat for as many titles on the disc as you want to copy. See also Copying from DVD to HDD on page 67. Can’t use One T ouch Copy (HDD to DVD) • Make sure that there is a recordable DVD loaded with some free space for recording and fewer than 99 titles already on the disc. Also make sure that for a Video mode disc, the disc isn ’t finalized. • If the title currently playing contains material that is copy-once protected, One T ouch Copy will not work. • If the currently playing HDD content was recorded in XP mode, the One T ouch Copy feature can’t be used. • One T ouch Copy doesn ’t work if the recorder is already recording to DVD. Can’t use One T ouch Copy (DVD to HDD) • Make sure that there is space available on the HDD and that there are fewer than 999 titles on the HDD. • One T ouch Copy doesn ’t work if the recorder is already recording to the HDD. The picture fr eezes and the front panel and remote contr ol buttons stop working • P ress  then tr y restarting playback. • P ress the front panel  STANDBY/ON button to switch the power off , then switch back on and restart playback. If the power fails to switch off , press and hold  STANDBY/ON for 10 seconds until the power switches off . Problem Remedy DVR-433H_UK.book 105 ページ ２００５年３月１日　火曜日　午後５時６分
Additional information 14 106 En • Can I use high-speed copy to copy from DVD to HDD? You can only use high-speed copy from DVD to HDD when copying Original titles from a VR mode DVD-R or DVD-RW disc. See also Copying from DVD to HDD on page 67. • Can I copy a copy-once protected program from a subscription satellite or cable channel to a DVD from the HDD? Yes, you can use high-speed copy to copy to a VR mode disc. You can also divide the recording on the HDD into a number of smaller titles if the whole recording won’t fit on to one disc. See also Copying from HDD to DVD on page 64. • Can I play a DVD I recorded on this recorder on another DVD player? Yes, you can generally play finalized Video mode discs recorded on this recorder on any standard DVD player. You may find, however, that some players will not play some recordable media. For VR mode DVD-RW discs, look for the ‘RW Compatible’ mark to see if it will play the disc. About DV Using DV, also known as i.LINK, you can connect a DV- equipped camcorder to this recorder using a single DV cable for input of audio, video, data and control signals. The i.LINK interface is also known as IEEE 1394-1995. “i.LINK” and the “i.LINK” logo are trademarks. • This recorder is only compatible with DV-format (DVC-SD) camcorders. Digital satellite receivers and Digital VHS video recorders are not compatible. • You cannot connect more than one DV camcorder at a time to this recorder. • You cannot control this recorder from external equipment connected via the DV IN jack. • It may not always be possible to control the connected camcorder via the DV IN jack. • Digital camcorders can usually record audio as stereo 16-bit/48kHz, or twin stereo tracks of 12-bit/ 32kHz. This recorder can only record one stereo audio track. Set the DV Input setting as required (see DV Input on page 95). • Audio input to the DV IN jack should be 32 or 48kHz (not 44.1kHz). • Picture disturbance in the recording may occur if the source component pauses playback or plays an unrecorded section of tape, or if the power fails in the source component, or the DV cable becomes disconnected. • The DV IN jack is an input only. There is no output functionality. DV-related messages You may see the following messages appear on your TV screen when using the DV IN jack. • No DV camcorder connected. – The camcorder is not connected properly, or the camcorder is switched off. • The DV camcorder is recording. – The camcorder is recording, so you cannot start recording from the camcorder to this recorder. • You cannot connect more than one DV camcorder at the same time. – The DV jack on this recorder supports connection to just one camcorder. • No tape in the DV camcorder. – There is no cassette loaded into the connected equipment. • The DV camcorder is in record-pause mode. – The camcorder is in record-pause mode. • DV camcorder playback canceled. Recording has been paused. – Recording was paused because the camcorder is not in playback mode. • Cannot operate the DV camcorder. – This recorder cannot control the camcorder. Try switching off the camcorder then switching it back on. • Could not operate the DV camcorder. – This recorder was not able to control the camcorder. • Recording has stopped because the recorded material on the tape finished. – When the recorded part of the DV tape comes to an end, this recorder automatically stops recording. • Recording has stopped because DV camcorder playback stopped. – Recording stopped because DV camcorder playback was stopped or the camcorder was disconnected. • The DV camcorder is not set for playback. Please select playback mode on the DV camcorder. – The camcorder is in camera mode. DVR-433H_UK.book 106 ページ ２００５年３月１日　火曜日　午後５時６分
Additional information 14 107 En Manual recording modes The table below shows the approximate recording times for a VR mode and Video mode DVD in each manual recording mode, as well as the standard recording mode equivalents. Levels separated by a bold line show where there is a noticeable change in picture quality. Audio recording in all manual recording modes is in Dolby Digital 2ch format, except for LPCM mode, which is in Linear PCM format. * The first figure refers to when the Input Line System is set to 525 System; the second when set to 625 System. ** XP mode is available for HDD recording only. If set for a DVD recording, the DVD will be recorded in MN32 mode. When recording to the HDD, recording for the times given will use approximately 4.7 GB of HDD space (equivalent to one recordable DVD). See also Recording on page 37. Video mode Off (HDD) VR mode (DVD) Video mode On (HDD) Video mode (DVD) Resolution* Level Rec. time Level Rec. time Resolution* 352 x 240 / 352 x 288 MN 1 802 mins. MN 1 802 mins. 352 x 240 / 352 x 288 MN 2 720 mins. MN 2 720 mins. MN 3 600 mins. SEP MN 3 600 mins. MN 4 480 mins. SLP MN 4 480 mins. MN 5 420 mins. MN 5 420 mins. MN 6 360 mins. EP MN 6 360 mins. 352 x 480 / 352 x 576 MN 7 300 mins. MN 7 300 mins. 352 x 480 / 352 x 576 MN 8 270 mins. MN 8 270 mins. 480 x 480 / 480 x 576 MN 9 240 mins. LP MN 9 240 mins. MN 10 230 mins. MN 10 230 mins. MN 11 220 mins. MN 11 220 mins. 544 x 480 / 544 x 576 MN 12 210 mins. MN 12 210 mins. 720 x 480 / 720 x 576 MN 13 200 mins. MN 13 200 mins. MN 14 190 mins. MN 14 190 mins. MN 15 180 mins. MN 15 180 mins. 720 x 480 / 720 x 576 MN 16 170 mins. MN 16 170 mins. MN 17 160 mins. MN 17 160 mins. MN 18 150 mins. MN 18 150 mins. MN 19 140 mins. MN 19 140 mins. MN 20 130 mins. MN 20 130 mins. MN 21 120 mins. SP MN 21 120 mins. MN 22 110 mins. MN 22 110 mins. MN 23 105 mins. MN 23 105 mins. MN 24 100 mins. MN 24 100 mins. MN 25 95 mins. MN 25 95 mins. MN 26 90 mins. MN 26 90 mins. MN 27 85 mins. MN 27 85 mins. MN 28 80 mins. MN 28 80 mins. MN 29 75 mins. MN 29 75 mins. MN 30 70 mins. MN 30 70 mins. MN 31 65 mins. MN 31 65 mins. MN 32 61 mins. XP MN 32 61 mins. LPCM 61 mins. LPCM 61 mins. XP ** 41 mins. XP ** 41 mins. DVR-433H_UK.book 107 ページ ２００５年３月１日　火曜日　午後５時６分
Additional information 14 108 En Language code list Language (Language code letter), Language code Country/Area code list Country/Area, Country/Area code , Code letter Japanese (ja), 1001 English (en), 0514 French (fr), 0618 German (de), 0405 Italian (it), 0920 Spanish (es), 0519 Chinese (zh), 2608 Dutch (nl), 1412 Portuguese (pt), 1620 Swedish (sv), 1922 Russian (ru), 1821 Korean (ko), 1115 Greek (el), 0512 Afar (aa), 0101 Abkhazian (ab), 0102 Afrikaans (af), 0106 Amharic (am), 0113 Arabic (ar), 0118 Assamese (as), 0119 Aymara (ay), 0125 Azerbaijani (az), 0126 Bashkir (ba), 0201 Byelorussian (be), 0205 Bulgarian (bg), 0207 Bihari (bh), 0208 Bislama (bi), 0209 Bengali (bn), 0214 Tibetan (bo), 0215 Breton (br), 0218 Catalan (ca), 0301 Corsican (co), 0315 Czech (cs), 0319 Welsh (cy), 0325 Danish (da), 0401 Bhutani (dz), 0426 Esperanto (eo), 0515 Estonian (et), 0520 Basque (eu), 0521 Persian (fa), 0601 Finnish (fi), 0609 Fiji (fj), 0610 Faroese (fo), 0615 Frisian (fy), 0625 Irish (ga), 0701 Scots-Gaelic (gd), 0704 Galician (gl), 0712 Guarani (gn), 0714 Gujarati (gu), 0721 Hausa (ha), 0801 Hindi (hi), 0809 Croatian (hr), 0818 Hungarian (hu), 0821 Armenian (hy), 0825 Interlingua (ia), 0901 Interlingue (ie), 0905 Inupiak (ik), 0911 Indonesian (in), 0914 Icelandic (is), 0919 Hebrew (iw), 0923 Yiddish (ji), 1009 Javanese (jw), 1023 Georgian (ka), 1101 Kazakh (kk), 1111 Greenlandic (kl), 1112 Cambodian (km), 1113 Kannada (kn), 1114 Kashmiri (ks), 1119 Kurdish (ku), 1121 Kirghiz (ky), 1125 Latin (la), 1201 Lingala (ln), 1214 Laothian (lo), 1215 Lithuanian (lt), 1220 Latvian (lv), 1222 Malagasy (mg), 1307 Maori (mi), 1309 Macedonian (mk), 1311 Malayalam (ml), 1312 Mongolian (mn), 1314 Moldavian (mo), 1315 Marathi (mr), 1318 Malay (ms), 1319 Maltese (mt), 1320 Burmese (my), 1325 Nauru (na), 1401 Nepali (ne), 1405 Norwegian (no), 1415 Occitan (oc), 1503 Oromo (om), 1513 Oriya (or), 1518 Panjabi (pa), 1601 Polish (pl), 1612 Pashto, Pushto (ps), 1619 Quechua (qu), 1721 Rhaeto-Romance (rm), 1813 Kirundi (rn), 1814 Romanian (ro), 1815 Kinyarwanda (rw), 1823 Sanskrit (sa), 1901 Sindhi (sd), 1904 Sangho (sg), 1907 Serbo-Croatian (sh), 1908 Sinhalese (si), 1909 Slovak (sk), 1911 Slovenian (sl), 1912 Samoan (sm), 1913 Shona (sn), 1914 Somali (so), 1915 Albanian (sq), 1917 Serbian (sr), 1918 Siswati (ss), 1919 Sesotho (st), 1920 Sundanese (su), 1921 Swahili (sw), 1923 Tamil (ta), 2001 Telugu (te), 2005 Tajik (tg), 2007 Thai (th), 2008 Tigrinya (ti), 2009 Turkmen (tk), 2011 Tagalog (tl), 2012 Setswana (tn), 2014 Tonga (to), 2015 Turkish (tr), 2018 Tsonga (ts), 2019 Tatar (tt), 2020 Twi (tw), 2023 Ukrainian (uk), 2111 Urdu (ur), 2118 Uzbek (uz), 2126 Vietnamese (vi), 2209 Volapük (vo), 2215 Wolof (wo), 2315 Xhosa (xh), 2408 Yoruba (yo), 2515 Zulu (zu), 2621 Argentina, 0118, ar Australia, 0121, au Austria, 0120, at Belgium, 0205, be Brazil, 0218, br Canada, 0301, ca Chile, 0312, cl China, 0314, cn Denmark, 0411, dk Finland, 0609, fi France, 0618, fr Germany, 0405, de Hong Kong, 0811, hk India, 0914, in Indonesia, 0904, id Italy, 0920, it Japan, 1016, jp Korea, Republic of, 1118, kr Malaysia, 1325, my Mexico, 1324, mx Netherlands, 1412, nl New Zealand, 1426, nz Norway, 1415, no Pakistan, 1611, pk Philippines, 1608, ph Portugal, 1620, pt Russian Federation, 1821, ru Singapore, 1907, sg Spain, 0519, es Sweden, 1905, se Switzerland, 0308, ch Taiwan, 2023, tw Thailand, 2008, th United Kingdom, 0702, gb USA, 2119, us DVR-433H_UK.book 108 ページ ２００５年３月１日　火曜日　午後５時６分
Additional information 14 109 En On-screen displays and recorder displays The table below shows a list of error messages that you may encounter when using the recorder and an explanation of their meaning. Message Explanation/Action • Initializing disc. Please wait a moment. When you load a blank DVD-RW disc, the recorder automatically initializes it. • Incompatible region number . The disc loaded has an incompatible region number for the recorder and so will not play . • Cannot recor d any more titles. • No more space for file management data. • Cannot add any more chapter marks. The disc control data limit has been reached, or the maximum number of chapters and/or titles has been reached. Erase titles/ chapters or combine chapters. • This disc cannot be recor ded. Undo the final- ization. The disc was finalized on a non-P ioneer DVD recorder . Undo the finalization in order to recording/editing. • Cannot play this disc. • This disc cannot be recor ded. • Cannot read the CPRM information. • Could not recor d the information to the disc. • Cannot edit. • Could not initialize disc. • Could not complete finalization successfully . • Could not undo finalization successfully . • Could not successfully unlock the disc. The disc may be dirty or damaged. T ake out the disc, clean it and retr y . If the error persists, use a new disc. If the error appears even with a new disc, please consult a P ioneer Ser vice Center . • Incompatible or unreadable disc. The disc loaded is a DVD R/RW , DVD-RAM or some other incompatible disc type. This display may also appear if the disc is dirty or damaged. • Cannot recor d to a disc that is not CPRM com- patible. • Cannot recor d this content using Video mode recor ding. The video source is copy-once protected. Use a VR mode DVD -R/ RW disc with CPRM for recording. • This content is copy protected. The video source is copy-protected and cannot be recorded. • Incorrect CPRM information. The recorder could not read the CPRM information. The recorder may be damaged—please consult a P ioneer Ser vice Center . • The audio will conform to the [Bilingual Recording] setting. When recording from an external input in Video mode (DVD), V ideo Mode On (HDD), or in LPCM mode, you can only record the left or right channel; not both. • Repairing disc. During recording, the power was cut. This display appears when the power is restored. • Could not repair the disc. The recorder was unable to repair the disc after a power cut. The contents of the recording will be lost. • Overheating has stopped operation. Press DISPLA Y to clear this message. The internal temperature of the recorder has exceeded the operating limit. If this message reappears, please contact a P ioneer authorized ser vice center . DVR-433H_UK.book 109 ページ ２００５年３月１日　火曜日　午後５時６分
Additional information 14 110 En • There is no DV input or the input signal is unr e- cordable. • Cannot preview because ther e is no DV input or the input signal is unrecor dable. No signal was detected at the DV IN jack. This may appear if a blank section of DV tape is playing in the connected camcorder . • HDD optimization is recommended. This can be done using Disc Setup. The HDD should be optimized (basically , HDD housekeeping) to maintain playback and recording per formance. • Please perform HDD optimization. This can be done using Disc Setup. The HDD is in more urgent need of optimization in order to maintain per formance. • The HDD has not been sufficiently optimized. Please optimize again. If this message appears repeatedly after optimizing the HDD it is likely that there is not enough free space on the HDD for optimization to complete properly . Please erase some titles from the HDD and optimize again. • This channel’ s TV system is differ ent from the recor der’ s setting. The TV system (P AL, NTSC, etc.) of the current channel is different from the TV system settings of this recorder . • Recording failed due to a TV system mismatch. Press DISPLA Y to clear message. The timer recording failed because the TV system of the channel set for recording was different from the setting of the recorder . • Playback has stopped because the TV system is differ ent than the recor ding. During recording or timer recording standby , the TV System (P AL, NTSC, etc.) of the playback video changed, causing playback to stop automatically . Message Explanation/Action DVR-433H_UK.book 110 ページ ２００５年３月１日　火曜日　午後５時６分
Additional information 14 111 En Resetting the recorder If you need to, you can reset the recorder to all its factory settings. 1 Make sure that the recorder is on. 2 Press and hold  and press  STANDBY/ON. The recorder turns off with all settings reset. Handling discs When holding discs of any type, take care not to leave fingerprints, dirt or scratches on the disc surface. Hold the disc by its edge or by the center hole and edge. Damaged or dirty discs can affect playback and recording performance. Take care also not to scratch the label side of the disc. Although not as fragile as the recorded side, scratches can still result in a disc becoming unusable. Should a disc become marked with fingerprints, dust, etc., clean using a soft, dry cloth, wiping the disc lightly from the center to the outside edge. Do not wipe with a circular motion. If necessary, use a cloth soaked in alcohol, or a commercially available CD/DVD cleaning kit to clean a disc more thoroughly. Never use benzine, thinner or other cleaning agents, including products designed for cleaning vinyl records. Storing discs Although CDs and DVD discs are more durable than vinyl records, you should still take care to handle and store discs correctly. When you're not using a disc, return it to its case and store upright. Avoid leaving discs in excessively cold, humid, or hot environments (including under direct sunlight). Don't glue paper or put stickers onto the disc, or use a pencil, ball-point pen or other sharp-tipped writing instrument. These could all damage the disc. For more detailed care information see the instructions that come with discs. Do not load more than one disc into the recorder. Damaged discs Discs spin at high speed inside the recorder. If you can see that a disc is cracked, chipped, warped, or otherwise damaged, don't risk using it; you could end up damaging the recorder. This recorder is designed for use with conventional, fully circular discs only. Use of shaped discs is not recommended for this product. Pioneer disclaims all liability arising in connection with the use of shaped discs. Cleaning the pickup lens The DVD recorder’s lens should not become dirty in normal use, but if for some reason it should malfunction due to dust or dirt, consult your nearest Pioneer- authorized service center. Although lens cleaners are commercially available, we do not recommend using them since some may damage the lens. Condensation Condensation may form inside the recorder if it is brought into a warm room from outside, or if the temperature of the room rises quickly. Although the condensation won’t damage the recorder, it may temporarily impair its performance. For this reason you should leave it to adjust to the warmer temperature for about an hour before switching on and using. DVR-433H_UK.book 111 ページ ２００５年３月１日　火曜日　午後５時６分
Additional information 14 112 En Hints on installation We want you to enjoy using this unit for years to come, so please bear in mind the following points when choosing a suitable location for it: Do...  Use in a well-ventilated room.  Place on a solid, flat, level surface, such as a table, shelf or stereo rack. Don’t...  Use in a place exposed to high temperatures or humidity, including near radiators and other heat- generating appliances.  Place on a window sill or other place where the recorder will be exposed to direct sunlight.  Use in a dusty or damp environment or in a room where it will be exposed to excessive cigarette smoke.  Place directly on top of an amplifier, or other component in your stereo system that becomes hot in use.  Use near a television or monitor as you may experience interference—especially if the television uses an indoor antenna.  Use in a kitchen or other room where the recorder may be exposed to smoke or steam.  Use on a thick rug or carpet, or cover with cloth—this may prevent proper cooling of the unit.  Place on an unstable surface, or one that is not large enough to support all four of the unit’s feet. Moving the recorder If you need to move the recorder, first remove the disc, if there’s one loaded, and close the disc tray. Next, press  STANDBY/ON to switch the power to standby, checking that the POWER OFF indication in the display goes off. Wait at least two minutes. Lastly, disconnect the power cord. Never lift or move the unit during playback or recording—discs rotate at a high speed and may be damaged. DVR-433H_UK.book 112 ページ ２００５年３月１日　火曜日　午後５時６分
Additional information 14 113 En Glossary Analog audio An electrical signal that directly represents sound. Compare this to digital audio which can be an electrical signal, but is an indirect representation of sound. See also Digital audio . Aspect ratio The width of a TV screen relative to its height. Conventional TVs are 4:3 (in other words, the screen is almost square); widescreen models are 16:9 (the screen is almost twice as wide as it is high). Chapter Just as a book is split up into several chapters, a title on the HDD/a DVD disc is usually divided into chapters. See also Title . Digital audio An indirect representation of sound by numbers. During recording, the sound is measured at discrete intervals (44,100 times a second for CD audio) by an analog-to- digital converter, generating a stream of numbers. On playback, a digital-to-analog converter generates an analog signal based on these numbers. See also Sampling frequency and Analog audio . Dolby Digital Dolby ® Digital Stereo Creator enables consumers to create stereo DVD-Videos with stunning Dolby Digital sound tracks at home. The technology, when utilized instead of PCM recording, also saves recordable disc space, allowing for higher video resolution or extended recording time on each DVD. DVDs mastered using Dolby Digital Stereo Creator will play back on all DVD- Video players. Manufactured under license from Dolby Laboratories. "Dolby" and the double-D symbol are trademarks of Dolby Laboratories. DRM (Digital Rights Management) DRM (Digital Rights Management) copy protection is a technology designed to prevent unauthorized copying by restricting playback, etc. of material on devices other the PC (or other WMA recording equipment) used to record it. For detailed information, please see the instruction manuals or help files that came with your PC (or other WMA recording equipment) and/or software. DTS DTS stands for Digital Theater System. DTS is a surround system different from Dolby Digital that has become a popular surround sound format for movies. “DTS” and “DTS Digital Out” are registered trademarks of Digital Theater Systems, Inc. Dynamic range The difference between the quietest and loudest sounds possible in an audio signal (without distorting or getting lost in noise). Dolby Digital and DTS soundtracks are capable of a wide dynamic range, delivering dramatic cinema-like effects. EXIF (Exchangeable Image File) A file format developed by Fuji Photo Film for digital still cameras. Digital cameras from various manufacturers use this compressed file format which carries date, time and thumbnail information, as well as the picture data. File extension A tag added to the end of a filename to indicate the type of file. For example, “.mp3” indicates an MP3 file. ISO 9660 format International standard for the volume and file structure of CD-ROM discs. JPEG A file format used for still images, such as photographs and illustrations. JPEG files are identified by the file extension “.jpg” or “.JPG”. Most digital cameras use this format. MP3 MP3 (MPEG1 audio layer 3) is a compressed audio file format. Files are recognized by their file extension “.mp3” or “.MP3”. DVR-433H_UK.book 113 ページ ２００５年３月１日　火曜日　午後５時６分
Additional information 14 114 En MPEG audio An audio format used on Video CDs and some DVD discs. This unit can convert MPEG audio to PCM format for wider compatibility with digital recorders and AV amp/receivers. See also PCM . MPEG video The video format used for Video CDs and DVDs. Video CD uses the older MPEG-1 standard, while DVD uses the newer and much better quality MPEG-2 standard. Optical digital output A jack that outputs digital audio in the form of light pulses. Connect components with optical digital jacks using a special optical cord, available from specialist audio dealers. PCM (Pulse Code Modulation) The most common system of encoding digital audio, found on CDs and DAT. Excellent quality, but requires a lot of data compared to formats such as Dolby Digital and MPEG audio. For compatibility with digital audio recorders (CD, MD and DAT) and AV amp/receivers with digital inputs, this unit can convert Dolby Digital and MPEG audio to PCM. See also Digital audio . PBC (PlayBack Control) (Video CD/Super VCD only) A system of navigating a Video CD/Super VCD through on-screen menus recorded onto the disc. Especially good for discs that you would normally not watch from beginning to end all at once—karaoke discs, for example. Regions (DVD-Video only) (example region code marks) Regions associate discs and players with particular areas of the world. This unit will only play discs that have compatible region codes. You can find the region code of your unit by looking on the rear panel. Some discs are compatible with more than one region (or all regions). Sampling frequency The rate at which sound is measured to be turned into digital audio data. The higher the rate, the better the sound quality, but the more digital information is generated. Standard CD audio has a sampling frequency of 44.1kHz, which means 44,100 samples (measurements) per second. See also Digital audio . Title A collection of chapters on a the HDD/DVD disc. See also Chapter . Track Audio CDs and Video CDs use tracks to divide up the content of a disc. The DVD equivalent is called a chapter. See also Chapter . WMA WMA is short for Windows Media Audio and refers to an audio compression technology developed by Microsoft Corporation. WMA data can be encoded by using Windows Media Player version 9 or 10, or Windows Media Player for Windows XP. Files are recognized by their file extension “.wma” or “.WMA”. Microsoft, Windows Media, and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States and/or other countries. 2 ALL DVR-433H_UK.book 114 ページ ２００５年３月１日　火曜日　午後５時６分
Additional information 14 115 En Specifications General System . . . . . . . . . . . . . . . . . . HDD, DVD-Video, DVD-R/RW, Video-CD, Super VCD, CD, CD-R/RW (WMA, MP3, JPEG, CD-DA) Power requirements . . . . . . . . . . . . . . . 220–240 V, 50/60 Hz Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 W Power consumption in standby mode 0.93 W (Front panel display: off) Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.0 kg Dimensions . . . . . . . . . . . . . . 420 (W) x 59 (H) x 273 (D) mm Operating temperature . . . . . . . . . . . . . . . . . 5°C to 35°C Operating humidity . . . . . . . . . . . . . . . . . . . . . . . . 5% to 85% (no condensation) TV system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PAL/SECAM/ NTSC (external input only) Recording Recording format . . . . . . . . . . . . . . . . DVD Video Recording DVD-VIDEO Recordable discs DVD-RW (DVD Re-recordable disc) DVD-R (DVD Recordable disc) Video recording format Sampling frequency . . . . . . . . . . . . . . . . . . . . . . . . . 13.5MHz Compression format . . . . . . . . . . . . . . . . . . . . . . . . . . . MPEG Audio recording format Sampling frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . 48kHz Compression format . . . . . . . . . Dolby Digital or Linear PCM (uncompressed) Recording time HDD (80GB) XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Approx. 11 hours Fine (XP) . . . . . . . . . . . . . . . . . . . . . . . . . . . Approx. 17 hours Standard Play (SP) . . . . . . . . . . . . . . . . . . . Approx. 34 hours Long Play (LP) . . . . . . . . . . . . . . . . . . . . . . . Approx. 68 hours Extended Play (EP) . . . . . . . . . . . . . . . . . . Approx. 102 hours Super Long Play (SLP) . . . . . . . . . . . . . . . Approx. 136 hours Super Extended Play (SEP) . . . . . . . . . . . Approx. 170 hours Manual Mode (MN) . . . . . . . . . . . . . . Approx. 17–227 hours DVD-R/DVD-RW Fine (XP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Approx. 1 hour Standard Play (SP) . . . . . . . . . . . . . . . . . . . . Approx. 2 hours Long Play (LP) . . . . . . . . . . . . . . . . . . . . . . . . Approx. 4 hours Extended Play (EP) . . . . . . . . . . . . . . . . . . . . Approx. 6 hours Super Long Play (SLP) . . . . . . . . . . . . . . . . . Approx. 8 hours Super Extended Play (SEP) . . . . . . . . . . . . Approx. 10 hours Manual Mode (MN) . . . . . . . . . . . . . . . . Approx. 1–13 hours Tuner Receivable channels Timer Programs . . . . . . . . . . . . . . . . . . . . . . 1 month/32 programs Clock . . . . . . . . . . . . . . . Quartz lock (24-hour digital display) Power off memory . . . . Approx. 5 years (after manufacture) Input/Output VHF/UHF antenna input/output terminal . . . . VHF/UHF set 75 Ω (IEC connector) Video input . . . . . . . . . . . . . . . . . . . . Input 1,3 (rear), 2 (front) Input level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Vp-p (75 Ω ) Jacks . . . . . . . . . . . . . . . . . . . . . . . AV connector 2 (Input 1), RCA jack (Input 2, 3) Video output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AV1, Output Output level . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Vp-p (75 Ω ) Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . AV connector (AV1) RCA jack (Output) S-Video input . . . . . . . . . . . . . . . . . Input 1, 3 (rear), 2 (front) Y (luminance) - Input level . . . . . . . . . . . . . . . . 1 Vp-p (75 Ω ) C (colour) - Input level . . . . . . . . . . . . . . . 300 mVp-p (75 Ω ) Jacks . . . . . . . . . . . . . . . . . . . . . . . AV connector 2 (Input 1), 4 pin mini DIN (Input 2, 3) S-Video output . . . . . . . . . . . . . . . . . . . . . . . . . . . AV1, Output Y (luminance) - Output level . . . . . . . . . . . . . . 1 Vp-p (75 Ω ) C (colour) - Output level . . . . . . . . . . . . . . 300 mVp-p (75 Ω ) Jacks . . . . . . . . . . . . . . . . . . . . . . . . . AV connector 1 (AV1), 4 pin mini DIN (Output) VHF (low) VHF (high) Hyper UHF VHF (low) VHF (high) Hyper UHF STEREO B/G - A2 I - NICAM L - NICAM B/G - NICAM D/K - NICAM Channel E2 - E4 X - Z E5 - E12 S1 - S20 M1 - M10 U1 - U10 S21 - S41 E21 - E69 Frequency 47 - 89 MHz 104 - 300 MHz 302 - 470 MHz 470 - 862 MHz Channel A - C X - Z D - J 11, 13 S1 - S20 S21 - S41 E21 - E69 Frequency 44 - 89 MHz 104 - 300 MHz 302 - 470 MHz 470 - 862 MHz SECAM B/G P AL B/G P AL I Channel FB, FC1, FC F1 - F6 B - Q S21 - S41 21 - 69 Frequency 49 - 65 MHz 104 - 300 MHz 300 - 470 MHz 470 - 862 MHz Channel R1 - R5 R6 - R12 S1 - S20 S21 - S41 E21 - E69 Frequency 49 - 94 MHz 104 - 300 MHz 302 - 470 MHz 470 - 862 MHz SECAM L SECAM D/K P AL D/K DVR-433H_UK.book 115 ページ ２００５年３月１日　火曜日　午後５時６分
Additional information 14 116 En Component video output Output level . . . . . . . . . . . . . . . . . . . . . . . . Y: 1.0 Vp-p (75 Ω ) P B , P R : 0.7 Vp-p (75 Ω ) Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RCA jacks RGB input Input level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.7 Vp-p (75 Ω ) Jacks . . . . . . . . . . . . . . . . . . . . . . . . AV connector 2 (Input 1) RGB output Output level . . . . . . . . . . . . . . . . . . . . . . . . . . .0.7 Vp-p (75 Ω ) Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . AV connector 1 (AV1) Audio input . . . . . . . . . . . . . . . Input 1, 3 (rear), 2 (front) L/R Input level During audio input . . . . . . . . . . . . . . . . . . . . . . . . . . . 2V rms (Input impedance: more than 22 k Ω ) Jacks . . . . . . . . . . . . . . . . . . . . . . AV connector 2 (Input 1), RCA jacks (Input 2, 3) Audio output . . . . . . . . . . . . . . . . . . . . . . . . . . . . AV1, Output During audio output . . . . . . . . . . . . . . . . . . . . . . . . . . 2V rms (Output impedance: less than 1.5 k Ω ) Jacks . . . . . . . . . . . . . . . . . . . . . . . . . AV connector 1 (AV1), RCA jacks (Output) Control input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mini jack DV input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 pin (front) (i.LINK/IEEE 1394 standard) AV Connectors (21-pin connector assignment) AV connector input/output . . . . . . . . . . . . 21-pin connector This connector provides the video and audio signals for connection to a compatible colour TV or monitor. PIN no. AV1(RGB)-TV / AV2(INPUT 1) 1. . . . . . . . . . . . . . . . . . . . . . . Audio 2/R out / Audio 2/R out 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – / Audio 2/R in 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G out / G in 3. . . . . . . . . . . . . . . . . . . . . . . . Audio 1/L out / Audio 1/L out 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – / Audio 1/L in 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . R or C out / R or C in 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND 17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B out / B in 19 . . . . . . . . . . . . . . . . . . . . . . . Video out or Y out / Video out 20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – / Video in or Y in 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Status 21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND Supplied accessories Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Dry cell batteries (AA/R6P) . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Audio / Video cable (red/white/yellow) . . . . . . . . . . . . . . . . 1 RF antenna cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Power cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Operating Instructions Warranty card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Note: The specifications and design of this product are subject to change without notice, due to improvement. DVR-433H_UK.book 116 ページ ２００５年３月１日　火曜日　午後５時６分
118 En Index A Audio digital output settings 95 DV audio settings 50 dynamic range control 91 external audio settings 94 input settings 94 setting preferences for audio language 96 switching on playback 61 switching TV audio 29 Auto start recording 49 Automatic channel setup 25 AV amplifier, connecting to 19 C CD Audio compatibility 9 playback controls for 33 , 55 – 61 Chapter automatic chapter marking 97 definition 113 editing 69 , 78 maximum number per title/disc 37 Component video 15 Copying from DVD to HDD 64 , 67 from HDD to DVD 64 – 66 , 102 high-speed 63 , 70 , 102 One Touch Copy 63 real-time 63 , 70 restrictions and copyright 63 Video mode compatible and frame accurate 68 , 69 , 70 D Dolby Digital explained 113 output setting 95 Downloading channel presets from the TV 13 , 25 DTS CD audio encoded with 33 explained 113 output setting 95 DV camcorder error messages 106 recording from 50 DVD activity display 35 aspect ratios 97, 101 backing up 71 compatibility 9, 37, 102 DVD-R vs DVD-RW 9, 10, 37, 102 finalizing 10, 51, 88 initializing 37, 87 playback controls for 32, 53– 62 selecting for playback/recording 27 Video mode vs VR mode 9, 10, 37, 74, 87, 97 E Easy Timer Recording 42 Editing 73– 81 Video mode compatibility and frame accuracy 74, 97 Video mode vs VR mode 74 H HDD activity display 35 backing up content to DVD 71 disk space and recording quality 107 playback controls for 32 precautions 11 selecting for playback/recording 27 Video mode compatibility 37, 74, 97 Home menu 34 J JPEG file compatibility 10 viewing in the PhotoViewer 85 Jukebox 82 L Language audio 61 , 96 code list 108 DVD menu 96 setting for menus and displays (OSD) 96 settings for DVD playback 96 subtitle 96 DVR-433H_UK.book 118 ページ ２００５年３月１日　火曜日　午後５時６分
119 En M MP3 audio files 9 , 113 MPEG audio 114 N NexTView 13 NTSC 24 O Optimized recording 45 P Picture quality recording time vs 38 , 107 setting for playback 90 setting for recording 89 Play List compared to Original 11 creating on a VR mode disc 75 switching to Play List view 73 Playback 29 – 33 , 53 – 62 on-screen displays 36 parental lock for DVD-Video 98 picture quality settings for 90 settings 97 Progressive scan video 27 R Recording 28 , 37 – 52 audio format 38 automatic chapter marking 97 copyright and 38 from a camcorder 50 from an external input 48 on-screen displays 36 optimized 97 settings 97 simultaneous playback and 48 time and picture quality 38 , 107 TV programs 28 , 39 Video mode vs VR mode 37 Recovery recording 41 , 45 Remote control buttons explained 22 –23 changing the batteries 8 operating range 8 setting the remote ID 98 S Subtitles setting preferences for 96 switching during playback 60 T Timer recording 41– 47 Title defined 114 maximum number recordable 37 maximum recordable length 37 thumbnails 76, 97 TV channels changing 29 manual setting 93 numbering 29 Recording - see Recording TV programs V Video CD compatibility 9 playback control (PBC) 33, 53 playback controls for 33, 55– 61 VIDEO Plus ® 43– 44 W WMA audio files 9, 10, 114 DVR-433H_UK.book 119 ページ ２００５年３月１日　火曜日　午後５時６分
PIONEER CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. BOX 1540, Long Beach, California 90810-1540, U.S.A. TEL: (800) 421-1404 PIONEER ELECTRONICS OF CANADA, INC. 300 Allstate Parkway, Markham, Ontario L3R OP2, Canada TEL: (905) 479-4411 PIONEER EUROPE NV Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11 PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936 TEL: 656-472-1111 PIONEER ELECTRONICS AUSTRALIA PTY. LTD. 178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: (03) 9586-6300 PIONEER ELECTRONICS DE MEXICO S.A. DE C.V. Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico,D.F. 11000 TEL: 55-9178-4270 K002E P ublished by P ioneer Corporation. Copyright © 2005 P ioneer Corporation. All rights reser ved. <VRB1379-A> P rinted in China DVR-433H_UK.book 120 ページ ２００５年３月１日　火曜日　午後５時６分