Pioneer Kuro Elite PRO-101FD Operating Instructions

<ARB1581-A> Printed in China Published by Pioneer Corporation. Copyright ÃÂ© 2008 Pioneer Corporation. All rights reserved. PIONEER CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. BOX 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404 PIONEER ELECTRONICS OF CANADA, INC. 300 Allstate Parkway, Markham, Ontario L3R 0P2, Canada TEL: 1-877-283-5901, 905-479-4411 PIONEER EUROPE NV Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11 PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555 PIONEER ELECTRONICS AUSTRALIA PTY. LTD. 178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: (03) 9586-6300 PIONEER ELECTRONICS DE MEXICO S.A. DE C.V. Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico, D.F. 11000 TEL: 55-9178-4270 K002_B_En Register Your Product on http://www.pioneerelectronics.com (US) http://www.pioneerelectronics.ca (Canada)
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (ser vicing) instructions in the literature accompanying the appliance. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER- SERVICEABLE P ARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN IMPORTANT D3-4-2-1-1_En-A Read these instructions. K eep these instructions. Heed all warnings. F ollow all instructions. Do not use this apparatus near water . Clean only with dr y cloth. Do not bloc k any v entilation openings. Install in accordance with the manuf acturerÃ¢ÂÂ s instructions. Do not install near any heat sources such as radiators, heat registers , stov es, or other apparatus (including amplifiers) that produce heat. Do not def eat the safety purpose of the polar ized or grounding-type plug. A polarized plug has tw o blades with one wider than the other . A grounding type plug has two b lades and a third grounding prong. The wide blade or the third prong are provided f or your saf ety . If the provided plug does not fit into your outlet, consult an electrician f or replacement of the obsolete outlet. Protect the power cord from being w alked on or pinched par ticularly at plugs, conv enience receptacles, and the point where the y exit from the apparatus. 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) Only use attachments/accessories specified by the manuf acturer . Use only with the car t, stand, tripod, bracket, or table specified b y the manuf acturer , or sold with the apparatus. When a car t is used, use caution when moving the cart/apparatus combination to av oid injur y from tip-ov er . Unplug this apparatus during lightning stor ms or when unused f or long periods of time. Ref er all ser vicing to qualified ser vice personnel. Ser vicing is required when the apparatus has been damaged in any w ay , such as power-supply cord or plug is damaged, liquid has been spilled or objects hav e fallen into the appar atus, the apparatus has been e xposed to rain or moisture, does not operate normally , or has been dropped. P1-4-2-2_En 11) 12) 13) 14) IMPORTANT NOT ICE Ã¢ÂÂ THE SERIAL NUMBER FOR THIS EQUIPMENT IS LOC ATED IN THE REAR. PLEASE WRITE THIS SERIAL NUMBER ON YOUR EN CLOSED WARRANTY CARD AND KEEP IN A SECURE AREA. TH IS IS FOR YO UR SECURITY. D1-4-2-6-1_En WARNING: Ha ndling the cord on this produc t or cords associated with accessories sold with the product will expose you to chemicals list ed on proposition 65 known to the State of Californ ia an d other governmental entities to cause cancer and birth defect or other reproductive harm. Wash hands after handling D36-P4-A_En PRO-141FD_PRO-101FD.book Page 2 Monday, May 12, 2008 3:27 PM
3 En TABLE OF CONTENTS Congratulations on purcha sing a Pioneer Elit e KURO monito r. At Pioneer, everything we do is de signed to alter percept ions, to shatter expect ations, to change the way people feel about sight and sound. This exc lusive se ries of E lite KU RO moni tors does j ust that. The result of a special limited run created for the entertainment purist, this monitor was de signed to excel under the most demanding situations, to be fully customizable to the most particular tastes and to transcend the ordinary. We are proud to incorporate this philosophy of exceptional qu ality, state-of-the-a rt design a nd meticulous engineering to make the Elite KURO monitor one of th e finest in the world and immerse you into one of the best entertainment experiences possible. Please spend some time readin g through this ownerÃ¢ÂÂs guide and manual to learn about the many feat ures and benefits that make this Elite KURO moni tor unique. We hope you enjoy the experience of owning an Elite KURO and i nvite you to enter a new world of seeing and hearing like never before. TABLE OF CONTENTS 1 Introduction to the Flat Panel Displays..................................................................................... ............. 6 1.1 Flat Panel Display S hipment Ch ecklist ............. .......... ............. .......... ........... .......... ........... ....... . .......... ......... ........ .......... 6 1.2 Control Options: Get to Kn ow Your Flat Panel Display ............. .......... ........... .......... ........... ............ ... ........ ........ .......... .. 7 1.2.1 Con trol Butto ns and More on the Flat Pa nel Display ......... .......... ........... .......... ........... ........ ........... ........ .......... .... 7 1.2.2 O perating the Rem ote Control ................... .......... ......... .......... ........... .......... .......... ........... . ... ........... ........ ........ ...... 8 1.2.3 Buttons on the Remote Control ......... ........... .......... ........... .......... ........... .......... ........... ........ ........ ......... ........ ........ 10 2 Install Your Flat Panel Display ............... .............................................................................. ................. 12 2.1 Use th e Optional Ta ble Top Stand (Stand) o r Equivalent Items ..... ............. .......... ........... .......... .......... ... .......... ........ .. 12 2.2 Use th e Optional Brack ets or Equivalent It ems . .......... ........... .......... ........... ............ ........... .......... . ....... ......... .......... .... 13 2.2.1 Che ck the Lo cation fo r Suitab ility ........... .......... ........... .......... ........ ........... .......... ........... .... .... ........ ......... ........ ...... 14 2.2.2 Lift and/or Mo ve Your Pane l (the Ho w ToÃ¢ÂÂs) . .......... ........... .......... ........... .......... ........... .......... .... .... ......... ........ ...... 14 2.2.3 Mount th e Flat Panel Display ........... ......... ........ ........ ........... ........ ......... ........ ........ ......... ... ....... ......... ........ .......... .. 15 2.3 Connect to Other Dev ices (DVR, Receiver, BDR, etc.) .... ......... ........ ......... .......... ........ ......... .......... ......... ........ ........ .... 17 2.4 Conn ect the Power Co rd to the Panel .. ............. .......... ........... .......... ........... ............ ........... ....... ... .......... ......... ........ ...... 19 2.5 Route then Bundle the Po wer Cord a nd Cables ............ ........... .......... ........... .......... ............. .......... .. ........... ........ ........ 19 3 Basic Operations............................................................................................................ ......................... 21 3.1 Turn the Flat Panel Display ON / OFF ............... .......... ............. .......... ........... .......... ........... ...... ...... ........... ........ ........ .... 21 3.2 Program Your Flat Panel Disp lay ...... .......... ......... ........ ........... ........ ........ ........... ........ ......... ... ....... ........ ........... ........ ...... 22 3.2.1 C hoose an Inp ut Source ........... ........ ......... ........ ........ ......... ........ ......... .......... ........ ......... . ......... ......... ........ .......... .. 22 3.2.2 Ex plore the Home Menu . ............ ............. .......... ........... ........ .......... ........... .......... ........... .. ...... ........ ......... .......... .... 22 3.2.3 Use the Simplified User Menu ..... ............. .......... ........... .......... ........... .......... ........ ........... ... ... ........ ......... ........ ...... 23 3.2.4 A ssign a Lan guage ........ ........ ........ ......... .......... ........ ......... ........ ........ ......... ........ ......... . ....... .......... ......... ........ ........ 24 4 Basic Picture Adjustment.................................................................................................... ................... 25 4.1 Adjust the Pic ture Quality ....... ........ ........ ........... ........ ........ ........... ........ ......... .......... ........ ..... ........ .......... ......... ...... ........ 25 4.1.1 Adjust the Picture for Yo ur Room Lighting .... .......... ........... .......... ........... .......... ........... .......... .. ......... ........ ........ .. 25 4.1.2 General Picture (Vid eo) Adjust ment ....... .......... ........... .......... .......... ........... .......... ......... ........ .. ......... ........ ........ .... 25 4.1.3 Compar e Images When Adjusting the Pictur e ........... .......... .......... ........... .......... ........... .......... ...... ............ ......... 27 4.2 Smart Starts for New Owners ........... ............. ............ ........... .......... .......... ........... ............ ..... .. ........ ........ ........... .......... .. 28 4.2.1 Ex tend Your Panel Life ...... ........ ........ ......... ........ ........ ......... ........ ......... ........ .......... ....... ...... ........ ......... ........ ........ .. 28 4.2.2 Adjust the Power Ind icator Brigh tness .... .......... ........... .......... ........... .......... ........ ........... ........ .. ......... ........ .......... 28 4.2.3 S et Input Priority ..... ......... ........ ........ ......... ........ ........ ......... .......... ......... ........ ........ ... ........ ........ ........ ......... ........ ...... 28 4.2.4 Tu rn On the Image Orbiter ..... ........ ......... ........ .......... ......... ........ ......... ........ ........ ......... .... ........ ......... .......... .......... 29 4.2.5 Trigger the Screen-Saving Video Pa ttern Periodically ... ............ ............. .......... ........... .......... ......... .......... ........ .. 29 4.2.6 Activate Energy Save to Reduce Power Usage ......... .. ...... ........ ......... ........ ........ ......... ........ ........ ......... ........ ........ 29 4.2.7 Tu rn On the Sleep Timer ... ........ ........ ........... ........ ......... ........ ........ ......... ........ ........ ......... .... ........ ......... ............ ...... 30 PRO-141FD_PRO-101FD.book Page 3 Monday, May 12, 2008 3:27 PM
4 En TABLE OF CONTENTS 5 Additional Picture Adjustment Options....................................................................................... ........ 31 5.1 Choose a n AV Op tion (Vid eo, Game , etc.) .......... ........ .......... ......... ........ ........... ........ ........ ........... .... ........ ........... ........ ... 31 5.1.1 AV So urce throug h the Remo te Control ............ ............. .......... ........ ........... .......... ........... ......... .......... ........ ........ . 31 5.1.2 Choose an AV So urce throug h the Hom e Menu .... ........... .......... ........... .......... ........... .......... .......... .. ................ .. 32 5.1.3 Choose a PC Sour ce .. ......... ........ ........ ......... ........ ........ ......... ........ ........ ........... ........ ...... .............. ............... ............ 32 5.1.4 Set the Panel to Recognize a Gam e Console ...... ............. .......... ........... .......... ........ ........... .......... ........... ........ ..... 32 5.2 Adjust Specific Pic ture Elements ...... .......... ........... .......... ........... ............ ........... .......... ......... ........ ........ ........... ........ ..... 33 5.2.1 Choose a Screen Size (Au tomatically or Man ually) ......... ........ .......... ........... .......... ........... .......... ... ...... ........ ....... 33 5.2.2 Correct t he Picture for an A V or PC S ource .... .......... ........... .......... ........... .......... ........... ........ ... ..... ......... ........ ..... 35 5.3 Assign Advanced Pic ture Functio ns ......... ........... ........ ........ ........... ........ ......... .......... ........ ....... .... ........ ........... ........ ..... 36 5.3.1 Adjust for Screen Masking (black bars on side s) ............ .......... ........... .......... ........ ........... .......... . ... ........... ........ . 36 5.3.2 Select a Color Temp erature Level ............. .......... .......... ........... .......... ........... .......... ........... .. .... ........ ......... ........ ..... 37 5.3.3 Adjust t he Image Grad ation Chara cteristics (Gamma ) ......... .......... ........... .......... ........... .......... ......... .... ........ ..... 38 5.3.4 Select a PureCinema Level for High Quality Im age.... ......... ........ ......... ........ .......... ......... ........ ....... ...... ........ ....... 38 5.3.5 Select a n Intellige nt Mode Opt ion... ............. .......... ........... .......... ........ ........... .......... ........... ........ ......... ........ ........ . 39 5.3.6 Select t he Picture Detail Option s ...... ............. .......... ........... ........ ........... .......... .......... ........ ... ........ ......... ........ ....... 40 5.3.7 Use CTI and C olor Spa ce ............... ........ ......... ........ ......... ........ .......... ......... ........ ........ ..... ........ ........ ......... .......... ... 4 0 5.3.8 Use th e Color Mana gement ....... ............ ........... .......... ........... .......... ......... .......... ........... ..... . ........ ........... ........ ....... 41 5.3.9 Reduce N oise from the Image ..... .......... ........... .......... ........... .......... ........... .......... ......... ...... .... ........ ......... ........ ..... 4 1 5.3.10 Adjust C olor Signal s ........... .......... ........... .......... .......... ........... .......... ......... .......... ....... .......... ........ ......... ........ ....... 42 5.4 View in Mu lti-Screen ...... ........... .......... .......... ............. .......... ........... .......... ........... .......... ......... ........ .......... ......... ........ ..... 43 5.4.1 Split / S wap / Sh ift the Screen ..... ............. .......... .......... ........... ........ ........... .......... ........... ........ ........ ......... ........ ..... 4 3 5.4.2 Turn the Small Screen On /Off .................. .......... .......... ........... .......... ........... .......... ........... . ....... ........ ......... ........ ... 44 5.5 Freeze the Picture .... .......... ......... ........ .......... ......... ........ ........... ........ ........ ........... ........ .... ......... .......... ........ ......... .......... . 44 5.6 Manage the Powe r . .......... ......... ........ .......... ......... ........ .......... ......... ........ ........... ........ ..... .......... ........ .......... ........... ........ . 45 6 Use Other Equipment With Your Flat Panel Display ........................................................................... 4 6 6.1 Program the Remote Control to Operate Othe r Equipment ........ ............ ............. .......... ........... .......... ..... .... .......... ..... 46 6.1.1 Use the Learning Fu nction ...... ........ ......... ........ ........ ........... ........ ........ ......... ........ ......... ... ....... ........ ......... ........ ..... 4 6 6.1.2 Assign a Manufactu ring Code t o the Remote C ontrol .. .............. ........... .......... ........... .......... .......... ... ........ ........ . 47 6.1.3 Issue a Libr ary Search for a Manufactu rer Code .... ........... .......... ......... .......... .......... ........... ......... . ......... ........ ..... 47 6.1.4 Clear Add ed Manufa cturer Codes from the Remote C ontrol ........... ........... .......... ........... .......... ........... .. ........ ... 48 6.1.5 Control a Pioneer Receiver .... .......... ........... ........ .......... ........... .......... ........... .......... ......... ...... .......... ......... ........ ..... 4 8 6.1.6 Control a Cable (CBL) or Satellite (S AT) System ................ .......... ........... ........ .......... ........... ....... ..... ......... ........ ... 49 6.1.7 Control a Video Cassette Recorder (VCR) ............. .... .. ......... ........ ......... ........ ........ ........... ........ ........ ......... ........ ... 50 6.1.8 Control a DVD Player/DVR Recorder/BD Player . ........... .......... .......... ........... .......... ........... .......... ... .... ........ ........ . 51 6.2 Apply Setting s for Other Equip ment .... .......... ......... ........ ........... ........ ........ ........... ........ ......... .. .......... ........ ......... .......... . 52 6.2.1 Apply Settin gs for an AV System . .......... ........... .......... ........... .......... ........... .......... ........... .... .... ........ ......... ........ ..... 52 6.2.2 Apply Settin gs for a PC .............. .......... ........... .......... ........... .......... ........... .......... .......... ........ ............... .............. .... 53 6.3 Use HDMI In puts .......... ........ ......... .......... ........ ......... .......... ......... ........ .......... ......... ....... ....... ......... ........ ........... ........ ....... 5 4 6.3.1 Enter an HDMI Input Name ....... ............ ........... .......... ........... .......... ........... .......... ........... ... . ........ ......... ........ ......... 54 6.3.2 Specify the HDMI Input Typ e ....... ............. .......... .......... ........... .......... ........... ........ ........... .. .... ........ ......... ........ ....... 55 6.3.3 Specify a Digital HDMI Signal Type ................. .... ........... ........ ........ ......... ........ ........ ......... ........ ........ ......... ........ ... 55 6.4 Control Equipment wi th the PanelÃ¢ÂÂs Remote Throug h HDMI ......... ............. .......... .......... ............. .......... ... ........ ......... 56 6.4.1 Control an AV System.. ........... .......... ........... .......... ........... .......... .......... ........... .......... .... ................ ............... .......... 58 6.4.2 Contro l a Recorder ........ ........... .......... ........... .......... ........... .......... ........... .......... ........ .. ..... .......... ........ ....... ........ ..... 5 9 6.4.3 Contro l a Player.... .......... ........... .......... ........... .......... ........... ........ .......... ........... ........ ......... ........ ........ ......... ........ ..... 59 6.4.4 Add an AV Amp or a BD Player ......... ........... .......... ........... .......... ........... .......... .......... .......... ..... ........... ........ ........ . 60 6.5 Specific KU RO LINK Comman ds ...... .......... ......... ........ ........... ........ ........ ........... ........ ........ ........ ..... ........ ........... ........ ... 61 6.5.1 Play Source Sound Using an HDMI Comm and .. ............. .. ........ ........ ......... ........ ......... ........ ........ ...... .............. .... 61 6.5.2 Turn O FF the Powe r With an HDMI Comm and ...... ........... .......... ........... .......... ........... .......... .......... .. .......... ........ 61 6.5.3 Turn O N the Power With an HDMI Com mand .... ............. .......... ........... .......... .......... ......... .......... ..... ...... .......... ... 6 1 6.5.4 Test the Po wer Cont rol (On/Of f) ...... ........... .......... ........... .......... .......... ........... .......... .......... . ........ ......... ........ ........ . 62 6.6 Connect a Game Co nsole or C amcorder ......... ........ ........ ........... ........ ........ ........... ........ ......... ....... ..... ........... ........ ....... 62 6.7 Use the IR REPEATE R OUT ... ......... ........ ........... ........ ........ ........... ........ ........ ........... ........ ...... .......... ............... .............. .. 62 6.8 Connect to a Netwo rk ...... ......... .......... ........ ......... .......... ........ ......... .......... ......... ........ ...... ......... ........ ........ ......... ........ ..... 63 6.8.1 IP Cont rol Setting ........ ......... ........ ........ ......... ........ ........ ......... ........ ......... .......... ........ ......... .......... ....... ........ ........ ... 64 6.8.2 Use th e Web Cont rol Syst em ............. ............. .......... ........... .......... ......... .......... .......... ........ ....... ............. .......... ..... 65 PRO-141FD_PRO-101FD.book Page 4 Monday, May 12, 2008 3:27 PM
5 En TABLE OF CONTENTS 6.9 Assign a Serial Num ber .............. ........ ........ ........... ........ ......... .......... ........ ......... .......... ..... ........ ........ ......... .......... ........ .. 69 6.9.1 A ssign an ID Nu mber ............... ........ ........... ........ ......... ........ ........ ......... ........ ........ ......... ........ ........ ........... ........ .... 69 6.9.2 A ssign a Baud Rate.. ......... ........ ........ ......... ........ ........ ......... ........ ......... .......... ........ ...... ... .......... ......... ...... ........ ...... 70 6.10 Selec t the Integrato r Mode ........... ............ ........... ............ ........... .......... ........... .......... ....... .. ........ ........ ........... .......... .... 70 6.10.1 Exp lore the Integ rator Mod e Menus ............. .......... ........... .......... ......... .......... ........... .......... .. .... ......... ........ ........ 71 7 Helpful Information ......................................................................................................... ...................... 75 7.1 Frequently Asked Questions (FAQs) ............... .......... .... ........... ........ ........ ........... ........ ........... ........ ........ ......... .......... .... 75 7.2 Cleanin g Methods ..... ........ ........... ........ ........ ........... ........ ......... .......... ........ ......... .......... . .......... ........ ............. ........ ........ .. 76 7.3 Trou bleshooting & Service Informat ion.... ........... ............ ........... .......... ........... .......... ............. ... ... ........ ........... ........ ...... 77 8 Cautions and Warnings....................................................................................................... ................... 80 8.1 Installation Details .......... ............. .......... ........... .......... ........... ............ ........... .......... .... ........... ........ ........ ........... ........ ...... 80 8.2 Physical Location & Temperature Consideration s .......... .... .......... ........ ......... .......... ......... ........ ........ ........... ........ ........ 80 8.3 Usag e Guidelines .. .......... ......... ........ .......... ......... ........ ........... ........ ........ ........... ........ .... ......... .......... ........ ......... .......... .... 80 8.4 Signal Interferen ce or Noise ........... .......... ........... ............ ........... .......... ........... .......... ........ . ........ ........ ........... .......... ...... 81 8.5 Phosp hor Properties .............. .......... .......... ............. .......... ........... .......... ........... ............ .. ..... ........ ........ ............. ........ ...... 81 8.6 Image Information Including R etention & A fter-Image Lag ....... .......... ........... .......... ............. .......... ...... ............ ......... 81 8.7 Prevent Burnin g ............ ............. .......... ........... ............ ........... .......... .......... ........... ....... ........ .......... ........ ......... .......... ...... 82 8.8 Safety Precau tions ...... ........ ......... .......... ......... ........ .......... ......... ........ ........... ........ ........ .... ......... .......... ......... ........ .......... 83 8.9 Legal No tices ..... .......... ........ ......... .......... ......... ........ .......... ......... ........ ........... ........ .... .... ........... ........ ........ ........... ........ .... 83 8.9.1 S afety ........... ........ ........ ......... ........ ........ ......... .......... ......... ........ ........ ......... ........ . ....... ....... ........ ........ ......... .......... .... 83 8.9.2 Ra dio Interferenc e ...... ......... ........ ........ ......... ........ ......... ........ ........ ......... .......... ........ .. ......... ........ ......... ...... .......... .. 84 9 Appendix ................................................. ................................................................... ............................ 85 9.1 Man ufacturer C odes to Pro gram into th e Remote Contro l .......... ............. ............ ........... .......... .......... ... ...... ........ ...... 85 9.1.1 C able ... ......... ........ ........ ......... ........ ........ ........... ........ ......... ........ ........ ......... ........ . ....... ......... ........ ......... .......... ........ .. 85 9.1.2 S atellite ........ ........ ........ ......... ........ ........ ......... ........ ......... .......... ........ ......... ........ . ..... ......... .......... ......... ........ ........ .... 86 9.1.3 VC R . ......... ........ ........ ........... ........ ........ ......... ........ ........ ......... ........ ......... ........ ..... ....... ......... ........ ......... ........ .......... .. 88 9.1.4 BDP ( Blu-ray) .... ........ ......... ........ ........ ......... .......... ......... ........ ........ ......... ........ ........ . ............ ........ ......... .......... ........ 91 9.1.5 DVD-R ... ......... ........ ......... ........ .......... ......... ........ ........ ......... ........ ........ ......... ........ . ........ ........ ........ ........... ........ ........ 92 9.1.6 DVD ..... ......... ........ ........ ......... ........ ........... ........ ........ ......... ........ ........ ......... ........ . .......... ........ .......... ......... ........ ........ 93 9.1.7 LD .......... ......... ........ ......... ........ ........ ......... .......... ........ ......... ........ ........ ......... ..... ............... .............. ............. ............. 95 9.2 Video/PC Signals (HDMI/DVI/ Component/min D-Sub/Composite) ............... .......... ......... ........ .......... ......... .... .... ...... 96 9.2.1 INPU T 1 (Video Signals) ........ ........ ......... .......... ........ ......... ........ ........ ......... ........ ......... ... ......... ........ ......... ........ ...... 96 9.2.2 INPU T 2 (Compo nent)/INPUT 3 (D-Sub) - Vid eo Signals (Analog) ... .......... .......... ........... .......... ........... ..... ......... 96 9.2.3 INPU T 4 (DVI)/INPUT 5 through 8 (HDMI) - Vide o Signals (Digital) . .......... .......... ........... .......... ........... ... ........... 97 9.2.4 INPU T 3 (D-Su b) - PC Sig nals (Analog ) .... .......... ........... .......... ........... .......... .......... ........... ...... .. ......... ........ .......... 98 9.2.5 INPU T 4 (DVI)/INPUT 5 t hrough 8 (HDMI) - PC Signa ls (Digital) ..... .......... .......... ........... ........ ........... .... ...... ...... 99 9.3 Specificat ions .. .......... ........ ......... .......... ........ ......... .......... ......... ........ .......... ......... ...... .... ........... ........ ........ ........... ........ .. 101 9.4 Trademarks ...... ........ .......... ......... ........ .......... ......... ........ ........... ........ ........ ........... ...... .. ........... ........ ........ ........... ........ .... 101 9.5 Glossary .... ......... .......... ........ ......... .......... ......... ........ .......... ......... ........ ........... ........ . ........... ....... .......... ......... ........ .......... 102 9.6 Index ...... ........ ........... ........ ......... .......... ........ ......... .......... ......... ........ .......... ......... .. .......... ......... ........ .......... ......... ........ .... 104 PRO-141FD_PRO-101FD.book Page 5 Monday, May 12, 2008 3:27 PM
6 En 01 Introduction to the Flat Panel Displays 1 Introduction to the Flat Panel Displays The P ioneer Flat P anel Display models incl ude the 60-i nch PRO-141FD a nd the 50-inch PRO-101FD (scree n sizes measured diagonall y). Below is a list of all accessori es sh ipped with your panel. If an item is missing, please contact your d ealer or our Ser vice organizati on immediatel y . Ser vice contact i nformatio n is listed on the back of this manual. 1.1 Flat Panel Display Shipment Checklist In addition to the flat panel display , there are several accessories included to make installati on quick and easy . Please check contents before discarding or allowi ng your installer to discard any packing material. Identify the accessories from the appropriate list below . Y ou will need a Philips screwdriver if removing or attaching the stand. Shipped with bot h models Remote Control Batteries fo r Remote (2) Cleaning Cloth P ower Cord (2 m /6.6 feet) Cable Clamps (4) Operating Instructions Certificate of Authenticity Ce rtificate Glossar y W arranty Card Specifications Sheet PRO-141FD_PRO-101FD.book Page 6 Monday, May 12, 2008 3:27 PM
7 En 01 Introduction to the Flat Panel Displays 1.2 Control Options: Get to Know Your Flat Panel Display Y ou can operate your flat panel display from the panel butto ns or with the remote cont rol. The following sections provide button locations/operations for the panel and the remote control. 1.2.1 Control Buttons and More on the Flat Panel D isplay Y our flat panel display has bu ttons, indicators, and sensors on the lower front bezel with more bu ttons on the rear panel. Refer to the drawings below for specific locations and func ti ons. Or , to identify back ports and termin als only , check the terminal posi tion sheet located nea r the panelÃ¢ÂÂs terminal compartment. T erminals on the rear panel are common to both models. PRO-141FD/PRO -101FD: Face of Panel 1 - P ower On indicator 2 - STANDBY indicator 3 - P ower On ( Ã¯ÂÂµ ) button 4 - Room Light se nsor 5 - Remote Control sensor 6 - ST ANDBY/ON button 7 - SCREEN SIZE button 8 - INPUT buttons 9 - Bezel (some call it the front frame) Back of the Panel (upper bank ) (from left to right) 1 - INPUT 1 terminal (V ideo) 2 - INPUT 2 terminals (Component, Y , C B /P B , C R /P R ) 3 - INPUT 3 terminal (Analog RGB) 4 - INPUT 4 terminal (DVI-D) 5 - INPUT 5 terminal (HDMI) 6 - INPUT 6 terminal (HDMI) 7 - INPUT 7 terminal (HDMI) 8 - INPUT 8 terminal (HDMI) 9 - RS-232C terminal (for factor y use) 10 - LAN terminal 11 - IR REP EA TER OUT te rminal 12 - AC In terminal 9 3 4 5 1 2 6 7 8 7 6 8 PRO-141F D (Right side) PRO-1 01FD (Bottom of the rear panel) 1 3 4 5 6 7 8 9 10 11 12 2 PRO-141FD_PRO-101FD.book Page 7 Monday, May 12, 2008 3:27 PM
8 En 01 Introduction to the Flat Panel Displays 1.2.2 Operating the Remote Control The remote control for the flat panel display is a power ful tool. This section provides a brief introduction to your remote control while later sections explore more advanced operations. Insert the Batteries into the Remote Control T o open, push and slide the battery co ver in the direction of the arrows. Load the supplied two AA si ze batteries by the negative pola rity (Ã¢ÂÂ) ends first. The batteries supplied with thi s prod uct may ha ve a shorter life expecta ncy due to storage con ditions. If the remote control seems to be f ailing or is weak, replac e the provided batteries with new alkaline batteries. Never mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical leaks in old ba tteries. Also , mixing different types or brands of batteries can ca use iss ues as b atteries brands have slightly different characteristics. Note: If the flat panel displayÃ¢ÂÂs remote control is not needed for an extended l ength of time, remove the batt eries. When disposing of used batteries, please comply with governmental regulations or envi ronmental public institution Ã¢ÂÂs rules that apply in your countr y/area. PRO-141FD_PRO-101FD.book Page 8 Monday, May 12, 2008 3:27 PM
9 En 01 Introduction to the Flat Panel Displays Remote Control Issues There are a s mall number of issues th at can affect your remote control but th e most common is weak ba tteries. W eak batteries in the remote control can cause communicatio n to fail or only operate sporadically . In this situation , tr y moving closer to the panel and at tempt to control the panel with the remote. If the panel responds, change the ba tteries. If moving cl oser has no eff ect on t he p a nel, check the surroundings for objects th at might be blocking the si gnal. Also consider other equipment with remote controls that are in the area around the panel. Objects and other IR signals can disrupt the remote. F or more help with your remote control, refer to Ã¢ÂÂ7.1 F requently Asked Questions (F AQs)Ã¢ÂÂ. Operating Range for the Remote Control T o control the flat panel display , poin t the remote towards the sensor on the panelÃ¢ÂÂs bottom right corner . F or easy operatio n, keep the distanc e between the remote control and the sensor less than 7 m (23 feet) and at an angle of less than 30 de grees. The remote control may not work properly if the sensor is in direct sunlight or very bright lighting. If your viewing room is naturally bright, chan ge the position of the panel or ph ysically us e the remote control clos er to the pane lÃ¢ÂÂs sensor . Note: If the rem ote contro l is lef t sitting i n direct s unlight or under a ver y stron g light, the case could warp or deform. 30ÃÂº Sensor 30ÃÂº 7 m (23 feet) PRO-141FD_PRO-101FD.book Page 9 Monday, May 12, 2008 3:27 PM
10 En 01 Introduction to the Flat Panel Displays 1.2.3 Buttons on the Remote Control Except for a few o ptions, commands avai lable through the buttons on the flat panel displ ay are duplicated on the remote control. The remote control can be programmed to control other equipment such as a DVD Player , Surround Sound system, etc. A later se ction entitled Ã¢ÂÂ6. Use Other E quipment With Y our Flat P anel Display Ã¢ÂÂ explains how to use the remote t o control other equipment. This section identifies and describes the buttons on the remote control. Remote: Left side buttons (top to bottom, left to right) MONITOR Ã¯ÂÂµ : T urn On or place panel in Standby 1 INPUT: Select a sou rce (INPUT 1 thru INPUT 8) 2 SPLIT: Cycle vie w thru sing le-screen, 2-scree n, picture-in-picture 3 SUB INPUT: Switch inputs for sub scre ens when viewing in multi-screen 4 AV SELECTION: Select audio /video settings A V Source: OPTIMUM, ST ANDARD, DYNAMIC, MOVIE, PURE, SPORT , GAME, USER PC Source: ST ANDARD, USER 5 AUTO SET UP: Optimize the PC screen 6 Number buttons 0 thru 9: Enter a number when appl ying IP Control Setting 7 KURO LINK: Select the K URO LINK functions 8 P/CH: Use the button for control of connected equipment 9 EXIT: Exit the me nu to return to the normal screen 10 Arrow buttons: Navigate the menu screens 11 HOME MENU/MENU: Display the HOME MENU 12 Color buttons (Red, Green, Blue , Yellow): Control a BD player for K URO LINK func tions only 13 Player/Recorder Control: Use buttons for control of connected equipment 14 SELECT: Select for MONITOR , STB, CBL/SA T , BDP/LD, DVD/DVR , VCR 15 1 MONITOR INPUT SPLIT FREEZE DISPLA Y MUTING MENU EXIT USER MENU RETURN ON DEMAND SOURCE DVD/HDD VOL RECEIVER EDIT/LEARN VCR STB MONITOR BDP LD DVD DVR CBL SA T SELECT F A VORITE INPUT TOO LS TOP MENU GUIDE HOME MENU INFO SW AP SUB INPUT PIP SHIFT AV SELECTION AUTO SET UP KURO LINK CH ENTER SCREEN SIZE 1 ENTER 234 8 7 6 5 23 456 78 0 9 P/CH 1 2 34 5 8 9 6 7 10 12 15 13 14 11 PRO-141FD_PRO-101FD.book Page 10 M onday, May 12, 2008 3 :27 PM
11 En 01 Introduction to the Flat Panel Displays Remote: Right side buttons (top to bottom, left to right) 16 :Lights all buttons (exc ept arrow buttons and the ENTER button) Lights turn off if no operation s are per formed within five seconds. Use this button for remote control use in dimly lit location s. 17 SWAP: Switch between the two screens when viewing as 2-s creen or pictu re-in-picture 18 PIP SHIFT: Move the location of the small screen when viewing as picture-in-picture 19 FREEZE: F reeze a frame from a moving image then press again to cancel the freeze function 20 SCREEN SIZE: Select the screen size 21 CH ENTE R: Use the button for control of connected equipment 22 DISPLAY/INFO : Display the current monitor status 23 i /Ã¢ÂÂ: Invalid 24 MUTING: Invalid 25 USER MENU/TOOLS: Display the User Menu 26 ENTER: Execute a command 27 RETURN: Re turn to the previous menu screen Note: If you set the preset code to MO NIT OR , but tons 9, 13, 14 and 21 do not operate. 1 MONITOR INPUT SPLIT FREEZE DISPLA Y MUTING MENU EXIT USER MENU RETURN ON DEMAND SOURCE DVD/HDD VOL RECEIVER EDIT/LEARN VCR STB MONITOR BDP LD DVD DVR CBL SA T SELECT F A VORITE INPUT TOO LS TOP MENU GUIDE HOME MENU INFO SW AP SUB INPUT PIP SHIFT AV SELECTION AUTO SET UP KURO LINK CH ENTER SCREEN SIZE 1 ENTER 234 8 7 6 5 23 456 78 0 9 P/CH 16 17 1 8 19 21 23 22 20 24 27 26 25 PRO-141FD_PRO-101FD.book Page 11 M onday, May 12, 2008 3 :27 PM
12 En 02 Install Your Flat Panel Display 2 Install Your Flat Panel Display There are several installation options for your flat panel display . This chapter walk s you through ho w to choose an installation site, the best mounting me thods, and how to install your panel. 2.1 Use the Optional Table Top Stand (Stand) or Equivalent Items Ã¢ÂÂ¢ Ask your dealer to perform the installation Ã¢ÂÂ¢ Use the supplied bolts Ã¢ÂÂ¢ F or details, refer to the instru ction manua l that came with the optiona l stand (or equivalent items) Use the supplied bolts when attaching the standÃ¢ÂÂ s supports at the holes indica ted by a circle. Rear view (PRO-141FD) Rear view (PRO-101FD) PRO-141FD_PRO-101FD.book Page 12 M onday, May 12, 2008 3 :27 PM
13 En 02 Install Your Flat Panel Display 2.2 Use the Optional Bra ckets or Equivalent Items Ã¢ÂÂ¢ Consult your dealer Ã¢ÂÂ¢ Use the following mountin g holes for installation Note: Some installation options require a diff erent type of bolt. Check with your installer or dealer to purchase the appropriate bolt(s). Rear view (PRO-141FD) Side view Mounting surf ace Mounting bracket (or equivalent item) M8 screw 12 mm to 18 mm (0.5 inches to 0.7 inches) Rear view (PRO-101FD) Mounting hole Mounting hole Mounting hole Mounting hole Mounting hole PRO-141FD_PRO-101FD.book Page 13 M onday, May 12, 2008 3 :27 PM
14 En 02 Install Your Flat Panel Display 2.2.1 Check the Location for Suitability When choosing the location for your panel, th ere are severa l factors to keep in mind. The installation site should be out of direct s unlight and have suffici ent ventilation ar ound the flat panel dis play to allow cooling. The diagram below is an example of a stand-mounted panel wi th proper ventilation. Use the checklist below to judg e possible installation sites. F or specific cautions and safety info rmation, refer to Ã¢ÂÂ8.2 Physical Location & T emperature ConsiderationsÃ¢ÂÂ and Ã¢ÂÂ8.8 Safety P recau tions.Ã¢ÂÂ 2.2.2 Lift and/or Move Yo ur Panel (the How ToÃ¢ÂÂs) This flat panel display is built for en durance but beca use of the technolo gy , the panel must be handled with care. Use the handles atta ched to the rear of the flat panel displa y to lift the unit. T o avoid flexing or twisting the unit, you need at least two people to lift and move the panel. Do not move the fla t panel display by hold ing only a single handle or b y dragging the pa nel by its handles . Note: Do not use the handles to hang the fla t panel display or as anchors to preve nt th e panel from slipping or tipping after it is mounted. Sufficient ventilation No da nger of power overloads Safe from excessive vibrations Se parate from ot her IR equipment Away from air cond itioners P rotec ted from hits or shocks F ree of moisture or dampness Distance from heat sou rces No danger of splashing wa ter Out of direct sunl ight Route cords and cables safely Away from strong ligh ting sources Over 10 cm (3 15/16 inches) Over 50 cm (19 11/16 inches) The distance behind and above the panel changes depending on your choice of mount. Consult with your dealer or professiona l installer for pr oper ventilation. (PRO-141FD) (PRO-1 01FD) PRO-141FD_PRO-101FD.book Page 14 M onday, May 12, 2008 3 :27 PM
15 En 02 Install Your Flat Panel Display 2.2.3 Mount the Flat Panel Display Because your flat panel display is slim but heavy , have at lea st two people mount and /or position the pane l. The following sections provide inst ructions fo r the different mounting and anchori ng options. Anchor the Panel When Using a Stand When using a stand, stabilize the panel to keep it from tipping over . Please use th e metal fittings and screws supplied with the optional stand to an chor the pa nel to a wall or other solid support structure. Another option is to purchase hooks, cords, and fi ttings through your installe r or from your local hardware store. The hardware size and strength depends on the co mposition and thickness of the anch oring sur face. Recommended hook: Nominal diameter 8 mm (3/8 inch), length 12 mm to 18 mm ( 0.5 inches to 0.7 inches) T o anchor the panel when using the op ti onal stand, follow the steps below . 1 ) A ttach the hooks to the mounting holes on the back of the panel. 2 ) Sink the fittings into the wall or support structure. 3 ) Run cords between the hooks and the fittings. 4 ) Tighte n the cords until the panel is anchored but not pulled off balance. T o stabilize the flat pane l display on a table or platform, use the metal fi ttings and screws supplied with the optional stand as well as commercially available wood screws. The wood screws are to anchor the metal fittings when mounting on a wooden surface. These screws shou ld have a nominal diameter of 4 mm (5/32 inch) and are at least 20 mm (13/16 inch) long. Notes: Avoid moving the tabl e af te r the p anel is attache d. Do not use bare wires for the cord. If any part of th e wire is intro duc ed into the ventilatio n port on the back of the display panel, fire or electrical shock could result. Fitting 2.Cord 1.Hook (PRO-14 1FD) M8 12 mm to 18 mm (0.5 inches to 0.7 inches) PRO-141FD_PRO-101FD.book Page 15 M onday, May 12, 2008 3 :27 PM
16 En 02 Install Your Flat Panel Display F ollow the steps below to secu re your fl at panel display . 1 ) Mark locations for metal fittings and screws on the ba ck edge of the table usi ng the panel stand to determine placement. 2 ) Drill holes in the table or plat form edge at the marke d locations. 3 ) Lif t panel into place with the assist ance with at least one other person . 4 ) U se wood screws (not included) to secu re the metal fittings to the table. Falling prevention metal fitting (supplied with the optional stand) Wood screw (commercially available, 4 mm x 20 mm (5/32 inch x 13/16 inch) min.) (PRO-1 41FD) PRO-141FD_PRO-101FD.book Page 16 M onday, May 12, 2008 3 :27 PM
17 En 02 Install Your Flat Panel Display 2.3 Connect to Other Devices (DVR, Receiver, BDR, etc.) The type of equipment attached to yo ur flat panel display determine s whic h panel ports are used. The following sections explain how to connect equipment such as a DV D player , video recorder , etc. to the panel. If your equipment is not listed, please refer to the operating instru ctions that came with the device (s) for connection assistance. Connect a DVD player: Connect DVI equipment: Use INPUT 2 terminals when connecting a DVD player or other audio/visual equipment. If your DVD player has an HDMI terminal, use this connection instead of making video connections. For details, refer to the operation manual th at came with the DVD player . DVD player HDMI compliant cable (HDMI cable having the HDMI mark) Component vide o cable (commercia lly available) Rear view Use a DVI-D 24-pin (digital only) cable to conn ect a PC equipped with a DVI output terminal (digital RGB signal). Af ter completing connections, follow the on- screen setup directions (p age 52). INPUT 4 supports Microsof t Ã¢ÂÂPlug & Play Ã¢ÂÂ (VESA DDC 2B) components. See Ã¢ÂÂ9.2 V ideo/PC Signals (HDMI/DVI/Compone nt/min D-Sub/Composite)Ã¢ÂÂ for info rmatio n about signals and display formats supported by INPUT 4. Rear view PC DVI-D cable (commercially avai lable) PRO-141FD_PRO-101FD.book Page 17 M onday, May 12, 2008 3 :27 PM
18 En 02 Install Your Flat Panel Display Connect a VCR: Connect HDMI equipment: Connect a game console or camcorder: Connect a PC: Use INPUT 1 terminal when connecting a VCR or other recording equipment. F or deta ils, refer to the operation manual that came with the device. VCR Video cable (commercially avai lable) Rear view HDMI equipment HDMI compliant cable (HDMI cable having the HDMI mark) Rear view INPUT 5 through INPUT 8 are HDMI terminals. F or details, refer to Ã¢ÂÂ6.3 Use HDMI Inputs.Ã¢ÂÂ Use INPUT 1 terminal when connecting a game console, camcorder , or other audio/visual equipment. F or details, refe r to the operation manual that came with the game console or camcorder . Rear view Video cable (commercially a vailable) Camcorder/Game console Personal computer Rear view Use INPU T 3 terminal (Analo g RGB) wh en conn ecting a computer (PC). F o r details, refer to the operation manual that came with the PC. RGB cable (commercially ava ilable) PRO-141FD_PRO-101FD.book Page 18 M onday, May 12, 2008 3 :27 PM
19 En 02 Install Your Flat Panel Display 2.4 Connect the Power Cord to the Panel The final connection is the power cord. Always connect the panelÃ¢ÂÂs power cord to a th ree-pronged outlet, verif ying that the cord is properly grounded. Th e cord includes a noise filter . Using an y other cord may fail to conform to mandator y FCC standards. As long as the flat panel display is plugged in to an ou tlet, some power is dra wn through the panel. W hen the flat panel display is not going to be used for a long period , un plug the panel from the power outlet. Unplugging the panel extends the life of the plasma as well as saves energy . Plug the cord in to the panel but do NOT plug it in to a power outlet yet. 2.5 Route then Bundle the Power Cord and Cables Once the flat pan el display is mounted, plac e additiona l equipment in the final position (s). Lay out the power cord, panel cables, and an y other device cabl es in a logical pattern that works f o r the location. Please consider the following points wh en routing cables: Ã¢ÂÂ¢ Access to a 3-prong (grounded) pow er outlet Ã¢ÂÂ¢ Space for the noise fil ter between the panel and outlet Ã¢ÂÂ¢ Placement of ca bles under ca rpets or across walking paths A reusable cabl e clamp is designed to lock the bundled cab les in place. Y our flat panel display has a total of three holes (60 inches: two holes) to attach cable clamps to the back of the panel. U se the cable cla mps as ne cessar y . Front Rear PRO-141F D PRO-1 01FD PRO-141FD_PRO-101FD.book Page 19 M onday, May 12, 2008 3 :27 PM
20 En 02 Install Your Flat Panel Display F ollow the steps below to attach a cable clamp. 1 ) T hread the clamp band thro ugh the holder and bundle the cable(s) in the cable clamp. 2 ) Push and hold the levers then insert the hook into an appropriate hole on the rear of the flat panel display . 3 ) Pull up the clamp band to lock. 4 ) Confirm that the cable clamp is seated firmly in the panel. Note: Avoid pinching or creat ing pressure po ints when routing or bundling cables. T o remove the clamp band, pull and hold the latch to release. T o remove the cable clamp, push and hold the le vers then pu ll it out from the hole. Note: The lon ger a cl amp is in place, the bette r chance o f deterioration . An older clamp is more easily damaged while being removed and may not be reusable. 1 2 Cable clamp Latch Lever Lever PRO-141FD_PRO-101FD.book Page 20 M onday, May 12, 2008 3 :27 PM
21 En Basic Operations 03 3 Basic Operations This chapter explores day-to-day operat ions such as powering on your flat panel displa y , using the Home Menu, User Menu, and adjusting the display f or the viewing area /room. The fin al section in this chapte r provides hints and suggestions for those new to flat panel display features. 3.1 Turn the Flat Panel Display ON / OFF Y our fla t panel displ ay has three ac tivity levels : P owe r On, Standby , and P ower Off . Standby saves energy but allows the remote control to turn on the panel. Th e follo wing in structions use the remo te control. T o operate th e flat panel di splay through the side panel buttons, refer to Ã¢ÂÂ1.2.1 Co ntro l Buttons and More on the Flat P anel DisplayÃ¢ÂÂ for button locations. Turn ON the Flat Panel Display T o turn on the pan el, follo w the steps below . 1 ) Plug the flat panel displayÃ¢ÂÂs power co rd in to a p roperly groun ded outlet. 2 ) Press any of the following buttons to turn the flat panel display On. Ã¢ÂÂ¢ Power On button ( a ) on the panelÃ¢ÂÂs back in lower-left section (see page 7) Ã¢ÂÂ¢ STANDBY/ON button on the side (PRO-141FD) or rea r (PRO-101FD) of the panel (see page 7) Ã¢ÂÂ¢ Remote controlÃ¢ÂÂs MONIT OR ( a ) button located in the upper left corner (see page 10) Images appear on the panel screen. 3 ) Con firm that the P ower On indicator lights blue. Note: While in Standby , pressing the remote controlÃ¢ÂÂs MONITOR ( a ) button causes the flat panel display to turn On. Turn OFF the Flat Panel Display T urning off the flat panel display can me an entering Standby so features are st ill fu nctional or it ca n mean cutting power to the panel. Unless the flat panel display is to sit idle for long periods, leave the panel in Standby . Note: While in Standb y or wh en pow ered off , the displa y cont inues to draw some power as long as the panel is plugged in to an outlet. F ollow the steps below to pl ace the panel in Standby . 1 ) Press the remote controlÃ¢ÂÂs MONITOR ( a ) button . 2 ) Confirm that the Sta n dby indicator lights red. The table to the right prov ides samples of how the indicators light. Monitor the indicators on the front of the panel to check the power status. Note: Select from Auto , High, Mid and Low . Selecting Auto toggles the brightness of the indicator between High, Mid an d Low to match the brightness level of the viewing area. Refer to Ã¢ÂÂ4.2.2 Adjust the Power Indicator Brightness.Ã¢ÂÂ Power Indicator Standby Indicator Flat Panel Display Status P anelÃ¢ÂÂs power cord is disconnected or the power cord is connected but the flat panel displayÃ¢ÂÂs P ower On button ( a ) is off P ower is o n but wait ing for act ivation P an el is in Sta ndby Po w e r O n i n d i c a t o r Standby indicator (PRO-101FD) PRO-141FD_PRO-101FD.book Page 21 M onday, May 12, 2008 3 :27 PM
22 En 03 Basic Operations 3.2 Program Your Flat Panel Display T o t a k e a d v a n t a g e o f s o m e b u ilt-in features, choose the input source, sel e ct a lan guage and set the picture qu ality . The sections below incl ude how to use the Home Menu and simplifi ed User Menu for each programming option. 3.2.1 Choose an Input Source T o choose an input source, note that the external equipm ent is properly connected to the inpu t terminals on the b ack of th e flat pane l displa y . F ollo w the directions below to choose an input source. P ress INPUT (but tons 1 through 8 ) on the remote control. The corresponding terminal/port number is selected as an input source. 3.2.2 Explore the Home M enu The Home Menu is the main me nu fo r the flat panel display . Most co mmands and settings are programme d through this menu. The following sect ion describes a typical method for wo rking with the p anelÃ¢ÂÂs menus. F or actual procedures, see the ap propriate page(s) that describe indiv idual functions. 1) P ress HOME MENU on the remote to access t he main menu. 2) Use the Up/Down arrows ( Ã¯ÂÂ©/Ã¯ÂÂª ) to highlight a menu item. 3) Use the Left/Right arrows ( Ã¯ÂÂ«/Ã¯ÂÂ¬ ) to scroll through opti ons for that menu item. 4) Highlight the selected menu option. 5) P ress ENTER to lock in the chan ge. 6) P ress RETURN to move back to a previous men u/submenu page when changi ng more than a single option. 7) P ress HOME MENU again to exit the menu screen. MONITOR INPUT SPLIT FREEZE SW AP SUB INPUT PIP SHIFT AV SELECTION AUTO SET UP SCREEN SIZE 1 234 8 7 6 5 MENU EXIT USER MENU RETURN TOOLS TOP MENU GUIDE HOME MENU ENTER HOME MENU FLA T P ANEL DISPLA Y Picture Screen P ower Control Option Control Setup Exit Input Setup Remote control Home Menu screen PRO-141FD_PRO-101FD.book Page 22 M onday, May 12, 2008 3 :27 PM
23 En Basic Operations 03 This chart provides a br eakdown of the Home Menu. 3.2.3 Use the Simplified User Menu F or simplified menu selections, the Us er Menu provid es quick access to frequ ent ly used menus/submenus. Pr e s s USER MENU on the remote control. F or ac tual procedu res, refer to Ã¢ÂÂ3.2.2 Explore the Home MenuÃ¢ÂÂ. The following table shows the available menus. Home Menu Pg Option Home Menu Pg Option Picture 31 AV Selecti on Power Control 29 Energy Save 35 Contrast 45 Power Management 35 Brightness 45 No Signal Off 35 Color 45 No Operation Off 35 Tint Option 24 Language 35 Sharpness 28 Input Priority 37 Color Temp 28 Blue LED Dimmer 35 Red 29 Orbiter 35 Green 29 Video Pattern 35 Blue 28 Long Life Settings 38 Gamma 25 Room Light Sensor 38 Pro A djust 44 PIP Dete ct 27 Reset Input Setup 52 Input Setup 1/2 Screen 53 Auto Setup 52 Input Setup 2/2 26 H. Position Control Setup 64 IP Control Setting 26 V. Position 58 KURO LINK Setting 53 Clock 69 Serial Setting 53 Phase 33 Auto Size 36 Side Mask 37 Reset User Menu Function Input Change switches ex ternal input sources A V Selection selects from eight viewing modes depending on the picture (see page 31) Film Mode reproduces theatre-qu ality images for film-based sources (see page 38) Sleep Ti mer places the panel into Standby when the set time elapses (see page 30) KURO LINK controls the connecte d equipment with th e panelÃ¢ÂÂs remote through HDMI (see page 56) USER MENU FLA T P ANEL DISPLA Y Input Change A V Selection : Standard Film Mode : Off Sleep Timer KURO LINK Exit User Menu screen PRO-141FD_PRO-101FD.book Page 23 M onday, May 12, 2008 3 :27 PM
24 En 03 Basic Operations 3.2.4 Assign a Language The default menu language is English. T o assign a different langua ge for menus and on-screen information , follow the steps below . 1 ) Access Language through the Option menu. 2 ) Select a language from the submenu. 3 ) Press HOME MENU to exit the menu. Language : English Input Priority : Off Blue LED Dimmer : Low Orbiter : Off Video P atter n : Off Long Life Settings : No Room Light Sensor : Off PIP Detect : Auto PRO-141FD_PRO-101FD.book Page 24 M onday, May 12, 2008 3 :27 PM
25 En Basic Picture Adjustment 04 4 Basic Picture Adjustment This chapter explores basic picture adjustment options fo r your flat panel display . 4.1 Adjust the Picture Quality Y our flat panel display has many adjus tment options for the picture to make it just right for you. Thi s section provides basic adj ustments but for detailed video modifications, refer to Ã¢ÂÂ5 A dditional P icture Adjustme nt Options.Ã¢ÂÂ 4.1.1 Adjust the Picture for Your Room Lighting The flat panel display senses the amou nt of light in your room and automatically adjusts the screen brightness for the best picture. Bright rooms re quire stronger coloring so images appear crisp whil e dimly lit rooms allow the picture to use more subtle coloring. The panel ships with the Room Light Se nsor turned Off . The sections b elow provide directions to turn the room lighting sensor On/Off . Room Lighting Sensor T o deactivate/reactivate the room lig hting sensor , follow the steps below . 1 ) Access Room Li ght Sensor through the Option menu. 2 ) Select On (or Off ) from the submenu. 3 ) Press HOME MENU to exit the menu. 4.1.2 General Picture (Video) Adjustment The directions below apply to all A V Selection options except OPTIMUM and DYNAMIC. If the viewing option is OPTIMUM, your flat panel display auto matically adjusts th e picture to the be st possible level. If the preferred viewing option is DYNAMIC, please refer to Ã¢ÂÂ5.1 C hoose an AV Option (Video, Game, etc.).Ã¢ÂÂ Language : English Input Priority : Off Blue LED Dimmer : Low Orbiter : Off Video P atter n : Off Long Life Settings : No Room Light Sensor : Off PIP Detect : Auto PRO-141FD_PRO-101FD.book Page 25 M onday, May 12, 2008 3 :27 PM
26 En 04 Basic Picture Adjustment F or standard picture adjustme nts, follow the steps below . 1 ) Press HOME MENU . 2 ) Select Pi c t u r e from the main menu. Use the arrow buttons to h ighlight an option t hen press ENTER . 3 ) S elect an item to be adjusted. Contra st is use d in the ex ample be low . 4 ) U se the arrow buttons ( Ã¯ÂÂ«/Ã¯ÂÂ¬ ) to adjust to the desi red level. 5 ) Press HOME MENU again to exit the menu. Picture Image Po sition Each input source stores the pict ure adjustment setting s for that view . Al though repositioning is available in most screen views, when the screen is se t to Dot by Dot, the P osition menu is unavailable. Also , depending on the displayed vide o, the image positi on may not change af ter an adjustment. T o adjust the pictureÃ¢ÂÂs horizontal and v e rtical position, follow the steps below . 1 ) Access H. Po s i t i o n or V. P o s i t i o n through the Screen menu. 2 ) A djust the vertical and/or horizont al positioning using th e arrow buttons. 3 ) Press HOME MENU to exit the menu. A V Selection : ST AND ARD Contrast : 40 Brightness : 0 Color : 0 Tint : 0 Sharpness : 0 Color T emp : Mid Red : 0 Green : 0 Blue : 0 Gamma : 3 Pro Adjust Reset Picture Contrast 32 Auto Setup H.P osition V .P osition Clock Phase Auto Siz e Side Mask Reset : No PRO-141FD_PRO-101FD.book Page 26 M onday, May 12, 2008 3 :27 PM
27 En Basic Picture Adjustment 04 Restore Default Picture After making multiple adjustments, it may be difficult to reverse improper settings. T o res tore the factor y default P icture settings, follow the directions below . 1 ) Access Rese t from the Picture menu. 2 ) Press ENTER to continue with the picture reset. 3 ) Use the arrow bu ttons to high light Ye s . 4 ) Press ENTER . All P icture settings return to the original default values. 4.1.3 Compare Images When Adjusting the Picture When adjusting the picture, look for an overall improvement by adjusting each parameter or option one at a time. Many small adjustments lead to the best pi c t u r e f o r y o u r v i e w i n g a r e a . A s e a c h o p t i o n c h a n g e s , r e f e r ba c k t o t h e previously set image for comparison . This section includ es adjustment notes an d steps to adjust the picture . Each parameter/option must b e adjust ed separately . F or example, if two options under A V Selection, ST ANDARD and MOVIE need adjustment, chang e/com pare one option t hen save the pref erred setting before moving on to the other option. Bel ow are other guidelines for picture adjustment. Ã¢ÂÂ¢ Adjustments are available while on the After s c r e e n . T r y i n g t o m a k e a d j u s t m e n t s w h i l e o n t h e Before causes a warning message to appear. Ã¢ÂÂ¢ Switch to anothe r parameter/option only from the After screen. If viewing the Before screen when selecting another option, the Before data is lost. Ã¢ÂÂ¢ Exiting a n option fr om the Before screen stores that previous entry in memory and deactivates the button . Ã¢ÂÂ¢ Exiting a n option fr om the After screen stores the new entry in memory and deactivates the button. Ã¢ÂÂ¢ Moving/changing the AV Selection parameter/option stores the option s etting in memo ry (the button continues to work). F ollow the steps below to adjust opti ons for the preferred picture quality . 1 ) Press HOME MENU . 2 ) Select Pi c t u r e from the main menu. Use the arrow buttons to high light an option then press ENTER . 3 ) Select an option. 4 ) Press USER MENU while the adjustment menu is on screen . The word Ã¢ÂÂBeforeÃ¢ÂÂ appears on screen with the unadjusted picture showing in Step 2. 5 ) Press USER MENU again . The adjusted picture appears an d the word Ã¢ÂÂBeforeÃ¢ÂÂ disappears. Pr e s s i n g USER MENU toggles the picture between Before and Af ter . 6 ) Repeat Steps 3 through 5 to adjust other picture options. 7 ) Press HOME MENU again to exit the menu. Notes: If no selectio ns are made within 60 seconds, the menu closes automati cally and the current settings are saved to memory . Ã¢ÂÂBeforeÃ¢ÂÂ is canceled if : Ã¢ÂÂ¢ The STANDBY/ON button, INPUT, SWAP or AV SELECTION is pressed Ã¢ÂÂ¢ input signal changes T o exit t he men u without savin g the chan ges, sw itch to the Before screen then press HOME MENU . PRO-141FD_PRO-101FD.book Page 27 M onday, May 12, 2008 3 :27 PM
28 En 04 Basic Picture Adjustment 4.2 Smart Starts for New Owners Many of the flat panel display features make it easier to use but also en vironmentally friendlier . This section explains how to extend the life of yo ur panel through being energy efficie n t. W e suggest a pplying all of the following functions below for the simplest us age, best quality , and longest l ife span. 4.2.1 Extend Your Pa nel Life This function provides short- cuts to your panelÃ¢ÂÂs longer service life. Y our flat panel display includes a Long Life Settings option. Activating this option causes the panel to automatic ally select several di fferent features tha t can prolong the life of your panel and help alleviate after-image ghosts or burn -in . T o set this option, follow the steps below . 1 ) Access Long Life Settings through the Option menu. A confirmation scre en appears. 2 ) Select Ye s from the s ubmenu. The following settings ar e automatically entered: Ã¢ÂÂ¢Auto Size: W ide Zoom Ã¢ÂÂ¢Side Mask - Detection: Mode 1 Ã¢ÂÂ¢Orbiter (A V source): Mode 1 Ã¢ÂÂ¢Orbiter (PC source): Mode 1 Ã¢ÂÂ¢Energy Save: Save 1 Ã¢ÂÂ¢A V Selection: OPTIMUM (only when it was set to D YNAMIC previously) 3 ) Press HOME MENU to exit the menu. 4.2.2 Adjust the Power Indicator Brightness Adjust the brightness of th e P ower On indicator depending on the brightness le vel of th e viewing area. Setting to Auto toggles the brightness of the in dicator between High, Mid and Lo w to match the brightness level of the viewing area. T o set the indicator , follow the directions below . 1 ) Access Blue LED Dimmer through the Option menu. 2 ) Select Auto , High, Mid or Low from the submenu. 3 ) Press HOME MENU to exit the menu . 4.2.3 Set Input Priority With a priority input assigned, the f lat panel display automatically switches to that input when signals are present. T o set the priority input, follow the directions below . 1 ) Access Input P riority through the Option menu . 2 ) Select Auto from the submenu. 3 ) Select the desired input. Detecting another signal at a differ ent input causes the selected input to automatically change to the new input. After input changes, the previous input is not rest ored even when the si gnal disappears at the input. 4 ) Press HOME MENU to exit the menu. PRO-141FD_PRO-101FD.book Page 28 M onday, May 12, 2008 3 :27 PM
29 En Basic Picture Adjustment 04 4.2.4 Turn On t he Image Orbiter A built-in feature to p rotect against burn -in is the Orbite r function. Orbiter slightly changes the position of the picture while the image is on scre en. T o activate Orbiter , follow the steps below . 1 ) Access Orbit er through the Option menu. 2 ) Select Mode 1 , Mode 2 or Off . Ã¢ÂÂ¢ A V source Mode 1: for any screen mode except Dot by Dot Ã¢ÂÂ¢ A V source Mode 2: for a ll available screen modes Ã¢ÂÂ¢ PC source Mode 1: to enable Orbiter Ã¢ÂÂ¢ PC source Mode 2: to smooth the tex t/character appearance 3 ) Press HOME MENU to exit the menu. Note: The farthest edge s of an image may be hidden at time s as the picture posi tion shifts. Also , when the Orbiter function is set to Mode 1 or Mod e 2, the imag e may appea r to drop slightly on the screen . 4.2.5 Trigger th e Screen-Savin g Video Pattern Periodically The Video P attern function causes the sc reen to appear white, which helps to alleviate after-im age ghosts or burn- in. While the Video P attern scre en is on, only the rem oteÃ¢ÂÂs MONITOR ( a ) button and t he panelÃ¢ÂÂs ST ANDBY/ON button are available. The panel auto matically switches to Standby one hour after running the Video P attern screen. T o canc el the Video P attern screen, press the remoteÃ¢ÂÂs MONITOR ( a ) or press the panelÃ¢ÂÂs ST ANDBY/ON button . T o activate the V ideo P attern screen, follow the steps below . 1 ) Access Video P attern through the Option menu. A confirmation screen appears. 2 ) Select Start from the s ubmenu. The Video P attern screen appears. 3 ) Leave the panel alone for a minimum of one hour . Note: The Video P attern timer has priority over Sleep Timer , No Signal Off , and No Operation Off (P ower Management) settings. 4.2.6 Activat e Energy Save to Reduce Power Usage The Energy Save option decreases picture brightness an d lowers power consumption . The recommended setting, Save 1, extends the life of your pane l while keeping power usage at a minimum. F ollow the steps below to activate an Energy Sav e option. 1 ) Access Energy Save through the P ower Control menu . 2 ) Select an option from the Energy Save subme nu. 3 ) Press HOME MENU to exit the menu. Note: T o deactivate the screen , select P icture Off . Option Description Standard No effect Save 1 consumes less power than Standard Save 2 consumes less power than Save 1 P icture Off activates P icture Off when closing th e Home Menu with this option selected PRO-141FD_PRO-101FD.book Page 29 M onday, May 12, 2008 3 :27 PM
30 En 04 Basic Picture Adjustment 4.2.7 Turn On the Slee p Timer T o save energy and to maximi ze the life of you r flat panel d isplay , tr y using the Sl eep Timer for occasions wh en the panel m ay be lef t on by a ccident. Th e Sleep Timer place s the pane l in Standb y when the s elected ti me elapse s. The Sleep Ti mer provides time periods of 30, 60, 90, or 120 minutes. When the Timer is down to five minutes, a reminder appears on sc reen each minute until the time h as elapsed. T o set the Sleep Timer , follow the steps below . 1 ) Press USER MENU . 2 ) Select Sleep T imer from the User Menu. 3 ) Select the desired time period. Select between 30 minutes and t wo hours (120 minutes). 4 ) Press USER MENU again to exit the menu. Note: When the sleep timer has been set, Ã¢ÂÂRemai n ---min Ã¢ÂÂ appears at the top of the menu. The Video P attern timer has p riority over the sleep time r . When the Video P attern timer is on, the sleep timer is deactivated. Video P attern is explaine d in an earlier section in this manual. PRO-141FD_PRO-101FD.book Page 30 M onday, May 12, 2008 3 :27 PM
31 En 05 Additional Picture Adjustment Options 5 Additional Picture Adjustm ent Options T o take a dvantage of all th at your flat panel d isplay offers, browse this chapter for features a nd functions that enhance your viewing experience. Most sections deal with adjusting the picture and arranging screen/menu items while the remaining sections pr ovide power management options. Apply as many or as few of these changes as d esired. 5.1 Choose an AV Option (Video, Gam e, etc.) Similar to the purpose for th e room light sensor , the A V Option or Selection depend s upon the brightness of the environment and the movie on screen . Images can be from either an AV Sou rce or from a PC. Both sources are discussed below . Choose from among the seven A V Selections for the best image from an external AV Source. Use either the remote control or the Home Men u to select the AV source. F or a PC, skip down to Ã¢ÂÂ5.1.3 Cho ose a PC So urce.Ã¢ÂÂ If th e AV so u rc e i s a G a me C on tr o l, se l ec t G A M E a nd r ef er t o Ã¢ÂÂ 5 .1 .4 S et th e P a ne l to Re co g ni ze a Ga m e C on s ol eÃ¢ÂÂ for more information. 5.1.1 AV Source through the Remote Control F ollow the directions below to set the A V Selection for an extern al AV Source. 1 ) Press AV SELEC TION on the remote control. The current A V selection appears. 2 ) Press AV SELEC TION again before th e displayed mode disappears. Each press cycles the options in the order shown below . 3 ) Allow the A V Selection screen to disappear . When the men u screen dis appears, the pa nel locks in the la st viewed option. AV Selection Description OPTIMUM automatically adjust s the image quality for the brightness level of the viewing area ST ANDA RD fo r a highly defin ed image in a no rmally bright room DYNAMIC for a very sharp image with maximum contrast but manual im age quality adjustme nt unavailable MOVIE for movies PURE reflects input signals as faithfully as possible for checking image materia ls, for example SPORT for sports programs GAME lowers image brightnes s for easier viewi ng USER allows cus tomizin g settings as desi red (set the mode for each input source) PRO-141FD_PRO-101FD.book Page 31 M onday, May 12, 2008 3 :27 PM
32 En 05 Additional Picture Adjustment Options 5.1.2 Choose an AV Source through the Home Menu Another method for choosi ng an AV Select ion uses the Home Menu. The A V Selection, OPTIMUM, automatica lly adjusts to the highes t i mage quality possible for the selected source and viewing environment. DYNAMIC locks out manual adjust ments for specific options. The DYNAMIC se tting blocks Contrast, Brightness, Color , Tint, Sharpness, and Reset. Unavai lable options are dimmed on the menu. T o choose an A V source throug h th e Home Menu, follow the steps below . 1 ) Access A V Selection through the Pi c t u r e menu. 2 ) Select an option from the submenu. 3 ) Press HOME MENU to exit the menu. 5.1.3 Choose a PC Source F rom a PC, choose between two A V Selections fo r the best image. The options are as follows: Ã¢ÂÂ¢ ST ANDARD: for a highly defined image in a normally bright room Ã¢ÂÂ¢ USER : allows customizing the settings for each input source 5.1.4 Set the Panel to Recognize a Game Console When adding a game console to your flat panel display , use the Game fun ction to esta blish a preference for image quality o r for operabil ity . T o have the panel store your Game preference, follow the steps below . 1 ) Access Pr o A d j u s t through the Pi c t u r e menu. 2 ) Select Other from the Pro Adjust menu. 3 ) Select Game C ontrol Pref . from the submenu. 4 ) Select On (operability preferred) or Off (image qua lity preferred). 5 ) Press HOME MENU to exit the menu. T o activate the Game Control Pref. option, set the AV Selection to GAME and use an external input (unless the sourse is coming from a PC). When a PC so urce menu is on screen, the Game C ontrol Pref . option is igno red. Also, the Game Control P ref . option for operability (on) is ignored du ring multi-s creen viewing (refer to Ã¢ÂÂ5.4 View in Multi-Screen Ã¢ÂÂ) and image freezing (refer to Ã¢ÂÂ5.5 F reeze the PictureÃ¢ÂÂ). OPTIMUM ST AND ARD D YNAMIC MO VIE PURE SPORT GAME USER A V Selection When OPTIMUM is se lected, images are r eproduced based on the information collect ed at the Room Light Sensor. PRO-141FD_PRO-101FD.book Page 32 M onday, May 12, 2008 3 :27 PM
33 En 05 Additional Picture Adjustment Options 5.2 Adjust Specific Picture Elements Plasma technology delivers one of the best images available today . However , the vi ewing area/environment and personal preferences affect ho w the picture appears. This section provides methods to adjust the picture for your best viewing experience. 5.2.1 Choose a Screen Size (Automatically or M anually) Automatic Screen Sizing The flat panel display can au tomatically select an appropriate scree n size for a video signal coming from an HDMI device. T o al low autom atic scre en sizing, follow the s teps belo w . 1 ) Access Auto Size through the Screen menu. 2 ) Select Natural or Wid e Z oo m from the submenu. 3 ) Press HOME MENU to exit the menu. Note: When a video signa l contains no aspect ratio in fo rmation, the Automatic Sc reen Si ze function is unavailable. Option Description Off deactivates the Auto Size function Natural adjusts the imag e to the screen size Wide Zoom enlarges an d displays on ly the 4:3 aspe ct ratio portion in full and wide screen PRO-141FD_PRO-101FD.book Page 33 M onday, May 12, 2008 3 :27 PM
34 En 05 Additional Picture Adjustment Options Manual Screen Sizing Manually select an appropriate screen size if an image fa ils to appear in the correct format. Browse the menu for the specific video signalÃ¢ÂÂs correct screen size. The selectable screen sizes differ depending on the type of input s ignal. While watching video content, press SCREEN SIZE on the remote control to cycle the picture thro ugh Auto , FULL, Dot by Dot, ZOOM, CINEM A, 4:3, WIDE, WIDE 1, WIDE 2, FULL 14:9 and CI NEMA 14:9. F reely change the screen size during video from oth er input sources. Auto is available when receiving HD pictures. The following chart provides information abou t how th e screen appears for ea ch option. With WIDE 1 or WIDE 2 selected, a Hi gh Definition (HD) picture image or menu may run off the edge of the screen. If an image or menu app ears cut or cropped, change the option to FULL. Avoid showing signals that fill only part of the screen. Im ages that fail to fill the screen may cause temporar y or permanent image retention depending on the frequenc y and duration. F or example, an HD picture with side masks (4:3 content) causes uneven wear of the plasma cell s. If side masks appear around a broadcast , after th at movie or program is over , switch to a full s creen motion video. This action helps the panel balance wear for the plasma cells and guar d against after-image issues. F or more information about Masks, refer to Ã¢ÂÂ5.3.1 A djust for Screen Masking (black bars on sides).Ã¢ÂÂ Note: Not all video signals carry alternative screen sizes. AV Option Description Auto adds side mas ks or di splays the image in full screen when detecti ng HD pictures containing side masks (See Detect Masks on page 36) FULL (FULL 14:9) squeezes 16:9 (14:9) images Dot by Dot matches input signal to the same n umber of screen pixels (available for 1080i or 1080p signals only) ZOOM bars may appear on the top and bottom on some pictures that are 16 :9 letterbox CINEMA CINEMA 14:9 bars may appear on the top and bottom on some pictures that are 14:9 letterbox (available for SD signals only) 4:3 side bars appe ar on each side WIDE pictures progressively stretch toward each side (available for SD signals only) WIDE 1 pictures progressively stretch toward each side (available for HD signals only) WIDE 2 pictures evenly stretch toward each side (available for HD signals only) PC Option Description 4:3 fills without altering the input signal aspect ratio FULL shows 16:9 screen display PRO-141FD_PRO-101FD.book Page 34 M onday, May 12, 2008 3 :27 PM
35 En 05 Additional Picture Adjustment Options 5.2.2 Correct the Picture for an AV or PC Source Although pi cture adjustments are to your persona l preferences, often the source causes unan ticipated image changes. Y our flat panel display offers se veral adjustment options. AV Source PC Source T o correct the picture for an A V or a PC source, follow the steps below . 1 ) Press HOME MENU . 2 ) Select Pi c t u r e from the main menu. Use the arrow buttons to high light an option then press ENTER . 3 ) Select an option to adjust. Option Left Arrow Right A rrow Contrast less contrast more contrast Brightness dimmer brighter Color weaker intensity stronger intensity Tint purplish skin tones greenish skin tones Sharpness s of ter definition crisper definition Color T emp adjusts white tone to your preference Gamma adjusts t he bala nce of im ageÃ¢ÂÂs b right a nd dark po rtions Option Left Arrow Right A rrow Contrast less contrast more contrast Brightness dimmer brighter Red weaker color stronger color Green weaker color stronger color Blue weaker color st ronger color A V Selection : ST ANDARD Contrast : 38 Brightness : -7 Color : -6 Tint : 5 Sharpness : 4 Color T emp : Mid Gamma : 5 Pro Adjust Reset Picture Exit (A V source) PRO-141FD_PRO-101FD.book Page 35 M onday, May 12, 2008 3 :27 PM
36 En 05 Additional Picture Adjustment Options 4 ) Select the desired level for that op tion using the left/right arrows ( Ã¯ÂÂ«/Ã¯ÂÂ¬ ). 5 ) Repeat the process for an y additional adjustments. 6 ) Press HOME MENU again to exit the menu after all adjustments are complet e. Note: Reset returns all settings to the factor y defaults. 5.3 Assign Advanced Picture Functions Y our flat panel display provi des various advanced functions for optimi zing the picture quality that go be yond basic adjustm ents explain ed earlier in th is manual. This section explores th e value offe red through Pioneer Ã¢ÂÂs Pro Adjust support, top quality blacks, better balanced whites, and overall color improvements. 5.3.1 Adjust for Screen Mask ing (black bars on sides) Screen Masks fill areas on both sides of a picture. Some content fails to fill the screen so bars appear on each side of the picture. This section ex plains how to adjust screen masking. Detect Masks Some HD video signals have 4:3 content with side masks. Side ma sks are black bars that a ppear on the pictureÃ¢ÂÂs left and right sides. If the fla t panel display Ã¢ÂÂs Screen Size is set to Natura l during the Auto Size process, gra y bars replace the black bars. When the panel is set to W ide Zoom, the bars are hidden . These responses reduce after- image concerns. T o allow the panel to detect side masks, follow the steps below . 1 ) Access Side Mask through the Screen menu. 2 ) Select Detectio n from the submenu. 3 ) Select Mode 1 or Mode 2 to activate Side Mask Detection. Mode 1 detects only bl ack side masks and Mode 2 detect s both black and illustrated side masks. Select Off to deactivate this function. 4 ) Press HOME MENU to exit the menu. Video signals can affect the Side Mask Detection function differently . F or High Definition pictures when Side Mask Detection is on , the panel auto matically detects images containing side masks and shows the picture in full screen. Cycle the screen size to select Auto for video si gnals that do not carr y aspect ratio information . Vide o content also ca n affect the Side Mask Detection funct ion. If a detection error oc curs when tr ying to watc h HD content, manually change the screen size to the prop er setting for the content. HD Wide Mode The HD Wide Mode allows sele cting th e display mode (WIDE 1 or WIDE 2) when detect ing side masks that appear in a 4:3 image. This option is availab le when the Auto Size menu is set to Wide Zoom and Side Mask Detection to Mode 1 or Mode 2. T o allow the HD Wide Mode, follow the steps below . 1 ) Access Side Mask through the Screen menu. 2 ) Select HD Wi de Mode from the s ubmenu. 3 ) Select Mode 1 or Mode 2 to activate HD W ide Mode. Ã¢ÂÂ¢ Mode 1: screen mode sets to WIDE 1 when detecting side masks . Ã¢ÂÂ¢ Mode 2: screen mode sets to WIDE 2 when detecting side masks . 4 ) Press HOME MENU to exit the menu. Contrast 32 PRO-141FD_PRO-101FD.book Page 36 M onday, May 12, 2008 3 :27 PM
37 En 05 Additional Picture Adjustment Options Lighten Side Masks If content appears with bars (side mask s) on each side of a picture when th e screen size is 4:3 and Side Mask Detection is active, the bars automa tically change from black to gra y . H owe ve r , th e gra y is fai rly d ark . T o chan ge the bars to a lighter shade of gray , follow the steps below . 1 ) Access Side Mask through th e Screen menu. 2 ) Select Brightness Sync . from the submenu. 3 ) Select the desired parameter . 4 ) Press HOME MENU to exit the menu. Restore Defa ult Screen T o restore the factor y default screen settings, follow the directions below . 1 ) Access Rese t through the Screen menu . 2 ) Press ENTER to continue with the screen reset. 3 ) Use the arrow bu ttons to high light Ye s . 4 ) Press ENTER . All screen settings return to the original default values. 5.3.2 Select a Color Temperature Level Use this op tion to adjus t the color tem perature for a be tter white bal ance. T o adjus t the white ba lance, foll ow the directions below . 1 ) Access Color T emp through th e Pi c t u r e menu . 2 ) Select the desired parameter from the submenu. T o manually adjust the white balance, continue with the following Steps. 3 ) Select Manual in Step 2. 4 ) Press ENTER to confirm. 5 ) Use th e right arrow button to adjust the balance. The manual adjustment screen appears. 6 ) Select an option to adjust. Parameter Description Fixed sets the same brig htness for gray side masks Auto adjusts the side mask br ightness according to th e brightness of screen images Parameter Description High white with bluish tone Mid-High intermediate tone between High and Mid Mid natural tone Mid-Low intermediate tone between Mid and Lo w Low white with reddish tone Manual adjusts to your preference PRO-141FD_PRO-101FD.book Page 37 M onday, May 12, 2008 3 :27 PM
38 En 05 Additional Picture Adjustment Options 7 ) Select the desired level. 8 ) Press RETURN to repeat Steps 6 and 7 as of ten as ne eded for additiona l adjustments. 9 ) Press HOME MENU to exit the menu. 5.3.3 Adjust the Image G radation Characteristics (Gamma) Use this option to adjust the imag e characteristics (gamma characterist ics). F or adjustme nts, follow the directions below . 1 ) Access Gamma through the Pi c t u r e menu. 2 ) Select 1 th rough 5 from the submenu. 3 ) Press HOME MENU to exit the menu. 5.3.4 Select a Pure Cinema Level for High Quality Image P ioneer Ã¢ÂÂs PureCinema automatically detects and analyses a film-based source (origina lly encoded at 24 frames per second) then recreates each frame for HD picture quality . Th e function supports both film and text material. T o set the P ureCinema level for your HD material, follow the steps below . 1 ) Access Pr o A d j u s t through the Pi c t u r e menu . 2 ) Select Pu r e C i n e m a from the Pro Adjust menu. 3 ) Select Fil m M o de or Te x t O p t i m i z a t i o n , dependi ng on the material. 4 ) Select the desired parameter . Option Left Arrow Right Arr ow R High fine adjustment for bright p ortions weaker red stronger red G High weaker green stronger green B High weaker blu e stronger blue R Low fine adjustment for dark portions weaker red stronger red G Low weaker green stronger green B Low weaker blue stronger blue Mode Parameter Description Film Mode Off deactivates P ureCinema Standard (not available for input signals 480p, 720p@60 Hz, or 1080p@60 Hz) automatically detects recorded DVD or high-definition images (e.g., movies) having 24 frames per second for sm ooth and vivid playback Smooth (not av ailable for in put signals 1080p@60 Hz) produces smoother a nd more vivid moving images Advance (not available for input signals 1080p@60 Hz) converts theatre-quality DVD images to 72 Hz (e.g., movies) Te x t Optimization Off deactivates text optimization On improves subtitle display quality PRO-141FD_PRO-101FD.book Page 38 M onday, May 12, 2008 3 :27 PM
39 En 05 Additional Picture Adjustment Options 5 ) Press HOME MENU to exit the menu. Notes: Activating the Game C ontrol P ref. setting under th e Option menu disables the PureCinema setting. This sett ing appl ies on ly to inp ut vide o sign als. 5.3.5 Select an Intelligent Mode Option Use this function to optimize image color tones and brightness. T o select the Intelligent M ode, follow the steps below . 1 ) Access Pr o A d j u s t through the Pi c t u r e menu . 2 ) Select Intelligent Mode from the Pro Adjust menu. 3 ) Select Mode 1 or Mode 2 (or Off ). 4 ) Select the desired parameter . 5 ) Press HOME MENU to exit the menu. Notes: Although this function gradually op timizes the image quality , tint and brightness changes may be visible. This is n ormal a nd is no t a malf unction. This sett ing appl ies on ly to inp ut vide o sign als. Parameter Description Off No effect Mode 1 compensates for more effective picture settings Mode 2 compensates for appropriat e picture settings PRO-141FD_PRO-101FD.book Page 39 M onday, May 12, 2008 3 :27 PM
40 En 05 Additional Picture Adjustment Options 5.3.6 Select the Pic ture Detail Options The P icture Detail function provides four adju stment options: DRE P icture, Black Level, ACL, an d Enhancer Mo de for enhanced image con trast and sharpness. T o select the P icture Detail op tions, follow the steps below . 1 ) Access Pr o A d j u s t through the Pi c t u r e menu . 2 ) Select P icture Detail from the subme nu. 3 ) Select DRE P icture, Black Level, ACL or Enhancer Mode. 4 ) Select the desired parameter . 5 ) Press HOME MENU to exit the menu. Note: This sett ing applie s only to inp ut video s ignals. 5.3.7 Use CTI and Color Space Use the Color T ransient Improvement (CTI) and Colo r Space options to furt her picture enhancement. T o set the CTI and Color Space op tions, follow the steps below . 1 ) Access Pr o A d j u s t through the Pi c t u r e menu . 2 ) Select Color Detail from the Pro Ad just menu. 3 ) Select CTI or Color Space from the s ubmenu. 4 ) Select the desired parameter . 5 ) Press HOME MENU to exit the menu. Option Parameter Description DRE P icture (emphasize s image contrast between light and dark) Off No effect High enhances DRE picture Mid standard DRE picture Low moderate DRE picture Black Level (emphasizes dark portion of images for enhanced contrast) Off No effect On activates Black Level ACL (compensates images for optimum contrast) Off No effect On activates ACL Enhancer Mode (processes the imageÃ¢ÂÂs hi gh frequency (detailed) area) 1 (Hard) selects Hard (SHARPNESS) image 2 (Natural) selects Natural (SHA RPNESS) image 3 (Soft) selects Soft (SHARPNESS) image Option Parameter Description CTI Off No effect On activates CTI Color Space 1 optimizes fo r vivid , vibrant co lor 2 standard color reproduction PRO-141FD_PRO-101FD.book Page 40 M onday, May 12, 2008 3 :27 PM
41 En 05 Additional Picture Adjustment Options Note: This setting applies only to i nput video signals. 5.3.8 Use the Color Management Use the Color Management option to fine adjus t image coloring. T o set the Color Management option , follow the steps below . 1 ) Access Pr o A d j u s t through the Pi c t u r e menu . 2 ) Select Color Detail from the Pro Adjust menu. 3 ) Select Color Management from the s ubmenu. 4 ) Select the desired parameter . 5 ) Select the desired level. 6 ) Press R ETURN or use the Ã¯ÂÂ«/Ã¯ÂÂ¬ button to repeat Steps 4 and 5 as needed. 7 ) Press HOME MENU to exit the menu. Note: This setting applies only to i nput video signals. 5.3.9 Reduce Noise f rom the Image Use the video n oise reductio n features fo r clear and cris p images. R efer to the table below for available video noise reduction. T o select the Noise R eduction op tions, follow the steps below . 1 ) Access Pr o A d j u s t through the Pi c t u r e menu . 2 ) Select Noise R eduction from the Pro Adjust menu. 3 ) Select 3DNR , Field NR , Block NR or Mosqui to NR . 4 ) Select the desired parameter . Item Left Arrow Right Arrow R clos er to magenta closer to yellow Y closer to red closer to green G clos er to yellow closer to cyan C closer to green clo ser to blue B closer to cyan closer to magent a M closer to blue closer to red Option Parameter Description 3DNR (3-dimen sional Nois e Red u ct i o n) Off No effect High enhances DNR Mid standard DNR Low moderate DNR Fiel d NR (removes glimmer for more natural image) Off No effect High enhances Field N R Mid standard F ield NR Low moderate Field NR Block NR (reduces noi se in HD images ) Off No effect On activates Block NR Mosquito NR (reduces mosquito noise in DVD and HD images) Off No effect On activates Mosquito NR PRO-141FD_PRO-101FD.book Page 41 M onday, May 12, 2008 3 :27 PM
42 En 05 Additional Picture Adjustment Options 5 ) Press HOME MENU to exit the menu. Note: This sett ing applie s only to inp ut video s ignals. 5.3.10 Adjust Color Signals Y our flat panel display fe atures va rious color signal adjustment op tions: 3DY C, I-P Mode, Drive Mode, Game Control P ref ., and Blue Only Mode. Use these options to adjust color signals for both video and still images. T o select color signal adjustment options, follow the steps below . 1 ) Access Pr o A d j u s t through the Pi c t u r e menu . 2 ) Select Other from the Pro Adjust menu. 3 ) Select 3DY C, I-P Mode, Drive Mode, Game Control P ref . or Blue Only Mode. 4 ) Select the desired parameter . Drive Mode is unavail able when setting Game Control P ref . to Off . T o activate the Game Control P ref . option, set the A V Select ion to GAME. This option is unavailable for a PC source. Also, the Game Cont rol P ref . op tion for operability (On) is ignore d during multi-sc reen vi ewing (page 43) or image freezes (page 44). 5 ) Press HOME MENU to exit the menu. Notes: Rese t returns all settin gs to factory defaults. This setting applies only to input video signals. Option Parameter Description 3DY C (optimizes characteristics for separating brightness signals from color signals) Off No effect High enhances 3DYC Mid standard 3DY C Low moderate 3D YC I-P Mode (provides optimum conversion from interlace signals to progre ssive signals) 1 (Motion) optimizes video images 2 (Standard) standard settin g 3 (Still) optimizes still images Drive Mode (switches image display frequency) 1 standard setting 2 enhances readability for horizontally scro lling text 3 optimizes movie content Game Con trol Pref . (est ablishes a gaming preference for image quality or operability) Off image quality preferred On operability preferred Blue Only Mode (displa ys images in blue only) Off No effect On activates Blue Only Mode PRO-141FD_PRO-101FD.book Page 42 M onday, May 12, 2008 3 :27 PM
43 En 05 Additional Picture Adjustment Options 5.4 View in Multi-Screen The flat panel d isplay can show multip le screens at the same time ; two-screen or picture-in-picture. The pictures may be reversed (in 2-sc reen and P -in-P) or m oved to variou s locations on the screen (P -in-P). 5.4.1 Split / Sw ap / Shift the Screen T o split the screen so that tw o input sources appear , press the SPLIT button on the remote control. Each press of the button cycles the screen through two-screen , picture-in-picture, and single-screen views. T o switch the image sides/locations, press the SWAP button. T o move the P icture-In-Picture (P -in-P) small image counter- clockwise, press the SHIFT button. 2-Screen P icture-in-P icture (P -in-P) PRO-141FD_PRO-101FD.book Page 43 M onday, May 12, 2008 3 :27 PM
44 En 05 Additional Picture Adjustment Options The multi-screen func tion is u navailable when viewing source from a single input or from two external input sources. T o return to a single picture, press HOME MENU . 5.4.2 Turn the Small Screen On/Off Set your flat panel display to automatically hide th e smal l screen window if no input signals appear on the small screen during P -in-P (only a frame remains on screen). T o activate this option, follow the directions below . 1 ) Access PIP Detect through th e Option menu. 2 ) Select Auto from the PIP Detect menu. The smal l screen dis appears in approx imatel y three seco nds if no signal i s received. The display restores the image when an input signal is present. 3 ) Press EXIT to exit the men u. Note: PIP Detect is unavailable in two-screen mode. 5.5 Freeze the Picture During fast-action seq uences or deta iled pictures, try capturing the im age with the FREEZE option . FREEZE a l l o w s y o u t o b e t t e r u n d e r s t a n d t h e a c t i o n o r p i c t u r e d e t a i l s w h e n d e s i r e d . To f r e e z e a p i c t u r e f r o m a T V b r o a d c a s t or movie, follow the steps below . 1 ) Press FREEZE to create a still image picture (copy) of the currentl y showing image. The copy appears to the ri ght of the still-moving video sequence thus splitting the screen. 2 ) Press FREEZE again to release the image. The frozen image disappears, returning the picture to a single screen with the video sequence still in progress. Ã¢ÂÂ¢ With the screen split, an image cannot be fr ozen. A warning messag e appears if you att empt to us e this fu nc tion when there is already a frozen image on screen. If an imag e is lef t frozen on th e screen, the panel automatically releases the image after five minutes. Note: Using FREEZE for an extended pe riod may cause an after-image. . Press SPLIT to cycle through the different multi- screen views. Press SWAP to switch the position of the two screens. Press PIP SHIF T to move the position of the small screen counter- clockwise during P-in-P . Press SUB INPUT to switch the input sources between the two screens. MONITOR INPUT SPLIT FREEZE SW AP SUB INPUT PIP SHIFT AV SELECTION AUTO SET UP SCREEN SIZE 1 234 8 7 6 5 Warning: Displaying pictures in multi-screen mode for an extended period ma y cause an after-image. MONITOR INPUT SPLIT FREEZE SW AP SUB INPUT PIP SHIFT AV SELECTION AUTO SET UP SCREEN SIZE 1 234 8 7 6 5 PRO-141FD_PRO-101FD.book Page 44 M onday, May 12, 2008 3 :27 PM
45 En 05 Additional Picture Adjustment Options 5.6 Manage the Power Y our fla t panel disp lay is ene rgy effic ient but incl udes fu nc tions to save additional power . In an earlier section entitled Ã¢ÂÂ4.2 Smart Starts fo r New OwnersÃ¢ÂÂ, you were told how to activate the E nergy Save feature. This section provides more advanced functions to sa ve power and to extend the panel life. AV Source - No Signal T o save energy and extend the life of your display , th e panel can ent er Standby automatica lly if the A V sou rce signal fails for 15 consecutive mi nutes. At five minutes before and at every minute af ter that, a warning message appears on the screen . When the final minute elapses, the panel switches to Standby . T o have the panel switch to St andby when an AV source signal fails, follow the steps below . 1 ) Access No Signal Off through the Power Control menu . 2 ) Select Enable to activate the A V Sign al off power function. 3 ) Press HOME MENU to exit the menu. AV Source - Non-Operat ional T o save energy , the panel can enter St andby automa tically if th ere are no commands from the A V source for three consecutive hou rs. At five minutes before and at every minute after that, a warning message appe ars on the screen. When the final minute elaps es, the panel switches to Standby . T o have the panel enter Standby automatically when th er e are no comma nds from the AV source, follow the steps below . 1 ) Access No Operation Off through the P ower Control menu. 2 ) Select Enable from No Operation Off menu. 3 ) Press HOME MENU to exit the menu. PC Source -Power Management When receiving signals from a PC, the panel can enter Standby automatically if the signal fails. F ollow the steps below to activate this function. 1 ) Access P ower Management through the P ower Control menu . 2 ) Select an option from the submenu. Notes: P ressing the remoteÃ¢ÂÂs MONITOR ( a ) b u t t o n o r t h e p a n e l Ã¢ÂÂ s ST ANDBY/O N button reacti vates the flat pane l display . When the panel enters Standby with Mode 1 selecte d (no signa ls receive d), receiv ing signal s again does not cause the flat panel display to turn On. When the panel enters the P ower Management status with Mode 2 selected (no signals received), receiving signal s again causes the flat panel display to turn On. 3 ) Press HOME MENU to exit the menu. These power management options are un available when a PC is connected to the panel through the HDMI port/ terminal. F or video and PC sign als applicable to the flat panel display , see Ã¢ÂÂ9.2 V ideo/PC Signals (HDMI/DVI/Component/ min D-Sub/Composite).Ã¢ÂÂ Option Description Off no power management (d efault) Mode 1 panel enters Standby wh en no signal is received from the PC for eight minut es , using the PC has no effect on the panel Mode 2 panel enters Standby wh en no signal is received from the PC for eight seconds , using the PC has no effect on the panel PRO-141FD_PRO-101FD.book Page 45 M onday, May 12, 2008 3 :27 PM
46 En 06 Use Other Equipment With Your Flat Panel Display 6 Use Other Equipment With Your Flat Panel Display Although ea rlier sections have ment ioned other equipment for playing back v ideo, this section provides control and operation information for sp ecific types of equipment. 6.1 Program the Remote Control to Operate Other Equipment T o operate other equipment or devices t hrough your flat panel di splay , prog ram the panelÃ¢ÂÂs remote control with the equipmentÃ¢ÂÂs manufacturing code. A manu facturing code is a series of numbers that identify the type of device and the br and. Thes e codes a re availa ble in the s ection entitled Ã¢ÂÂManufactu rer Codes to P rogram in to the Remote ControlÃ¢ÂÂ in Ap pendix 9. 1 of this manu al. 6.1.1 Use the Learning Function The Learning function allows the pane lÃ¢ÂÂs remote control to memorize codes to control other devices. T o set the Learning function to On , follow the directions below . 1 ) Press SELECT to choose the other device. 2 ) Simultaneously press the EDIT/LEARN and 2 butt ons to begin. The selected mode indica tor flashe s when the remote control is ready to be prog rammed. 3 ) U se the number buttons to learn a manufac turing code. The mode indicator lights up. The Learn session is canceled in 30 seconds and the indicator begins blinking again . When the indicato r flashes, the selecte d deviceÃ¢ÂÂs remote is memorized. When you press a button that ca nnot be learned, the indicator continues to blink. T o exit the Learn mode before it finishes, press EDIT/LEARN . 4 ) Press EDIT/LEARN again to exit the Lean mode after the code is confirmed. : Notes: The Learn sessi on cancels if: Ã¢ÂÂ¢ no operatio n is per formed for more than one minute af ter having pressed EDIT/LEARN and 2 (the mode indicator is flashin g) Ã¢ÂÂ¢y o u p r e s s SELECT Code transmission finishes in approximately two seconds. Do not interrupt the process until the transmission is complete. When using any of t h e receiver buttons ( a , INPUT , or VOL /Ã¢ÂÂ) , the l earned manufacturer code remains the same. EDIT/LEARN VCR STB MONITOR BDP LD DVD DVR CBL SA T SELECT INPUT SUB PI P 1 2 34 8 7 6 5 2 cm to 5 cm (0 .8 inches to 2. 0 inches) Remote control (Supplied accessory) Remote control of AV product PRO-141FD_PRO-101FD.book Page 46 M onday, May 12, 2008 3 :27 PM
47 En Use Other Equipment With Your Flat Panel Display 06 T o delete a learned code, overwrite it with a new code on the same button or follow the directions below . 1 ) Simultaneously press the EDIT/LEARN an d 2 bu ttons to begin . The selected mode indicator flashes when th e remote control is re ady to be programmed. 2 ) Press and hold MONITOR a for at least two seconds. The remote control st arts deleting all learned co des for selected modes. Wh en completed, the mode indicator blinks Off and the remote control returns to normal operation . 6.1.2 Assign a Manufacturing Code to the Remote Control T o assign a preset Manufacturing code t o the panelÃ¢ÂÂs remote control, follow the directions below (Manufact uring codes are listed in section Ã¢ÂÂ9.1 Manufacturer Co des to P rog ra m into the Remote ControlÃ¢ÂÂ). 1 ) Press SELECT to choose the device to program. 2 ) Simultaneously press the EDIT and 1 bu ttons to begin . The selected mode indicator flas hes when the remo te control is ready to be programmed. 3 ) Use the number buttons to ente r a manufacturer code . When the indicator turns off , th e code has been stored in the remote control. F actor y default manufac ture codes: STB (Set-top Box): P ioneer (0329) BDP/LD/DVD/DVR : P ioneer (2052) VCR (VTR): P ioneer (0058) 6.1.3 Issue a Library S earch for a Manufacturer Code If the code for a particular devic e is unknown , cycle through the availa ble codes for a sim ilar unit then sample som e function s for that code. T o find a code that can control th e unit, follow the steps below using different cod es to find the be st match. 1 ) Press SELECT to choose the device to program. 2 ) Simultaneously press the EDIT and 3 bu ttons to begin . The selected mode indicator flas hes when the remote control is ready to search the code librar y . 3 ) S ample a code using a SOURCE POWER , PL AY , 1 or CH command. 4 ) Use the up/down arrow ( Ã¯ÂÂ©/Ã¯ÂÂª ) buttons to advance to the next code if the sampled code fails to control the device. Another option is to return to the previous code and rep eat Step 3. 5 ) Press ENTER to lock in the code th at properly op erates the de vice. All the available buttons for the selected mode are added when the mode indicator flashes on for one secon d. The remote control then returns to normal operation. EDIT /LEARN VCR STB MONITOR BDP LD DVD DVR CBL SA T SELECT INPUT SUB PI P 1 234 8 7 6 5 MENU EXIT USER MENU RETURN ON DEMAND SOURCE DVD/HDD VOL RECEIVER EDIT /LEARN VCR STB MONITOR BDP LD DVD DVR CBL SA T SELECT F A VORITE INPUT TOO LS TOP MENU GUIDE HOME MENU ENTER SUB PI P 12 3 4 8 7 6 5 PRO-141FD_PRO-101FD.book Page 47 Mond ay, May 12, 2008 3 :27 PM
48 En 06 Use Other Equipment With Your Flat Panel Display 6.1.4 Clear Added Manuf acturer Codes from the Remote Control T o return all learned and pres et codes to th e defaults (PIONEER), follow the steps below . T o exit before the reset is complete, press the EDIT button again. The reset is cancel led if no action is taken withi n 60 seconds. Switching the Mode during this procedure also cancels the reset. 6.1.5 Control a Pioneer Receiver The flat panel displa y Ã¢ÂÂs remote control has a bank of bu ttons specifically for contro l ling a Pioneer receiver . The active buttons, left to right, are as follows: 1 ) Simultaneously press EDIT and MONITOR ( Ã¯ÂÂµ ) button s to begin. Selectio n can be in an y mode . 2 ) Press the Yellow button to clear a dded codes. Confirm that the selected mode indicator flashes. The remote control enters the Manufacturing Reset mode. The reset is complete when th e mo de indicator flashes once. The remote control then retu rns to normal operation. Note: The panelÃ¢ÂÂs remote control may not control or have complet e control of some equipment listed in the tables. Ã¢ÂÂ¢ RECEIVER S TANDBY/ON (turns the Pioneer Receiver On/Off) Ã¢ÂÂ¢ RECEIVER INPU T (cycles through/selects an input) Ã¢ÂÂ¢ RECEIVE R VOL Ã¢ÂÂ (adjusts the volume lower) Ã¢ÂÂ¢ RECEIVE R VOL (adjusts the volume higher) M E N U O N D E M A N D S O U R C E D V D / H DD V O L R E C E I V E R E D I T / L E A R N V C R S T B M O N I T O R B D P L D D V D D V R C B L S A T S E L E C T F A V O R I T E I N P U T M O N I T O R I N P U T 1234 SOURCE DVD/HDD VOL RECEIVER EDIT/LEARN VCR STB MONITOR BDP LD DVD DVR CBL SA T SELECT INPUT PRO-141FD_PRO-101FD.book Page 48 M onday, May 12, 2008 3 :27 PM
49 En Use Other Equipment With Your Flat Panel Display 06 6.1.6 Control a Cable (CBL ) or Satellite (SAT) System When Mode is set to CBL/SA T , a cable converter uses the buttons 1 , 2 , 5 , and 6 . However , the panel only recognizes a single system (cab le or satellite) at a time. Ã¢ÂÂ¢ N u m b e r b u t t o n s (press to enter a channel number) Ã¢ÂÂ¢ P / C H / Ã¢ÂÂ (selects a higher or lower channe l) Ã¢ÂÂ¢ E N T E R (ENTER activates the selected function) Ã¢ÂÂ¢ S O U R C E (turns the e quipment power on and o ff) Ã¢ÂÂ¢ C H E N T E R * (enters the selected chan nel wi th the direct channel se lection buttons) Ã¢ÂÂ¢ R E T U R N (restores the immediately previous screen) * Some cable converter manufacturers do not preset CH ENTER. 1 2 3 4 5 6 1 MONITOR INPUT SPLIT FREEZE DISPLA Y MUTING MENU EXIT USER MENU RETURN ON DEMAND SOURCE DVD/HDD VOL RECEIVER EDIT/LEARN VCR STB MONITOR BDP LD DVD DVR CBL SA T SELECT F A VORITE INPUT TOO LS TOP MENU GUIDE HOME MENU INFO SW AP SUB INPUT PIP SHIFT AV SELECTION AUTO SET UP KURO LINK CH ENTER SCREEN SIZE 1 ENTER 234 8 7 6 5 23 456 78 0 9 P/CH 1 5 6 2 4 3 PRO-141FD_PRO-101FD.book Page 49 M onday, May 12, 2008 3 :27 PM
50 En 06 Use Other Equipment With Your Flat Panel Display 6.1.7 Control a Video Ca ssette Recorder (VCR) When Mode is set to VCR, verif y that the proper Input is selected (INPUT 1 to INPUT 8) then use the numbers 1 to 8 to control the device. Ã¢ÂÂ¢ P / C H / Ã¢ÂÂ (selects a higher or lower channel ) Ã¢ÂÂ¢ R E C o r d (begins recording) Ã¢ÂÂ¢ P A U S E / S T I L L (pauses playback and displays st ill images) Ã¢ÂÂ¢ S O U R C E (turns the VCRÃ¢ÂÂs pow er on and off) Ã¢ÂÂ¢ REWind (rewinds the VCR tape and allows searches) Ã¢ÂÂ¢ S T O P (halts VCR tape transport) Ã¢ÂÂ¢ P L A Y (selects playback) Ã¢ÂÂ¢ F F (advances the VCR ta pe and allows searches) 1 2 3 4 5 6 7 8 DISPLA Y MUTING MENU EXIT USER MENU RETURN ON DEMAND SOURCE DVD/HDD VOL RECEIVER EDIT/LEARN VCR STB MONITOR BDP LD DVD DVR CBL SA T SELECT F A VORITE INPUT TOO LS TOP MENU GUIDE HOME MENU INFO KURO LINK CH ENTER ENTER 78 0 9 P/CH 7 8 6 1 4 3 2 5 PRO-141FD_PRO-101FD.book Page 50 M onday, May 12, 2008 3 :27 PM
51 En Use Other Equipment With Your Flat Panel Display 06 6.1.8 Contr ol a DVD Player /DVR Recorde r/BD Play er When Mode is set to DVD/DVR , the remote control can operate a DVD player , DVD recorder or BD player connected to the flat panel di splay . V erify that the proper Input is se lected for the device then use the numbers 1 to 14 to control it. Note: Equipment from other manufacturers ( DVD players, DV D recorders, BD players, and HD-DVD players) can also be operated using the panelÃ¢ÂÂs remote contro l if the remote is programmed for the device(s). Ã¢ÂÂ¢ P/CH /Ã¢ÂÂ (DVD Recorder onl y) (selects a higher or lower channe l) Ã¢ÂÂ¢ DVD TOP MENU (displays the top menu on the DVD) Ã¢ÂÂ¢ E N T E R (ENTER activates the selected function) (arrows to select from MENU screens) Ã¢ÂÂ¢ DVD MENU (displays the DVD menu) Ã¢ÂÂ¢ Red/Green/Blue/Yellow (BD only) (controls a BD-J applicatio n) Ã¢ÂÂ¢ RECord (DVD Recorder only) (begins recording) Ã¢ÂÂ¢ P A U S E / S T I L L (pauses playback and displays still image) Ã¢ÂÂ¢ S O U R C E (turns the e quipment power on or off ) Ã¢ÂÂ¢ REVERSE SCAN /CHAPTER SEARCH (press once quickly to go to beginning of current chapter; press aga in to go back to the beginnin g of the previous ch apter; continue pressing to go backward) Ã¢ÂÂ¢ T O O L S (assigns the co de for a Pioneer BD player) Ã¢ÂÂ¢ R E T U R N (restores the immediately previous screen) Ã¢ÂÂ¢ S T O P (halts DVD playback, some DVD players/recorders open the disc tray if this button is pressed twice) Ã¢ÂÂ¢ P L A Y (selects playback) Ã¢ÂÂ¢ FORWARD SCAN/CHAPTER SEARCH (press once quickly to go to beginning of next chapter; press again to advance to beginning of next chapter; continue pressing for fast forward) & STOP RECord (DVD Recorder only) (press and hold Ã¯ÂÂ« then press Ã¯ÂÂ§ to stop recording - applies to P i oneer DVD recorders only) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 6 12 DISPLA Y MUTING MENU EXIT USER MENU RETURN ON DEMAND SOURCE DVD/HDD VOL RECEIVER EDIT/LEARN VCR STB MONITOR BDP LD DVD DVR CBL SA T SELECT F A VORITE INPUT TOOLS TOP MENU GUIDE HOME MENU INFO KURO LINK CH ENTER ENTER 78 0 9 P/CH 2 4 5 14 13 12 11 10 1 8 7 6 3 9 PRO-141FD_PRO-101FD.book Page 51 M onday, May 12, 2008 3 :27 PM
52 En 06 Use Other Equipment With Your Flat Panel Display 6.2 Apply Settings for Other Equipment This section provides sett ing hints for the connected equipment including devices using Composite V ideo, Component Video , and DVI equipment as well as a PC. F or connection details, see page 17. 6.2.1 Apply Sett ings for an AV System After connecting other equipment to your flat panel display , you may need to enter an input name, color signal and signal type, depending on the in put you select. F or details on settin gs, follow the directions below . Composite/Component Video System 1 ) Access INPUT 1(Video) or INPUT 2(Component) through th e Input Setup menu. 2 ) Select the desired items. Ã¢ÂÂ¢I N P U T 1 ( V i d e o ) Vide o, Blu-Ray , DVD, DVR, VCR , Cable, Satellite, GAME or Computer for Input Name; Auto, P AL, SECAM, NTSC, 4.43NTSC, PA L - M o r PA L - N f o r C o l o r S y s t e m Ã¢ÂÂ¢I N P U T 2 ( C o m p o n e n t ) Component, Blu -Ray , DVD, DVR, VCR , Cable, Satellite, GAME or Compute r; Comp.1 (Y CbCr) or Comp.2 (YPbP r) 3 ) Press EXIT to exit the men u. Notes: The factory default setting is Co mp. 1 for SD signals and Comp. 2 for HD signals. Improper setting for Color Decoding causes the image to appear in inappropriate color . DVI Equipment 1 ) Access INPUT 4(DVI) through the Input Setup menu. 2 ) Select the desired item. DVI, Blu-Ra y , DVD, DVR, VCR, Cable, Satell ite, GAME or Computer; Vide o or PC for Signal T ype; Auto, 1 (YUV422), 2 (YUV444), 3 (RGB16-235) or 4 (RGB 0-255) for V ideo 3 ) Press EXIT to exit the men u. Notes: After setting DVI, turn on the conn ected equipment (reboot if a PC is connected). Changing the s ettings while leaving the connected equi pment turned On ma y cause the signa l to fail or b ecome corrupted. Connecting to a PCÃ¢ÂÂs DVI terminal us ing an HDMI cable can cause imprope r images to appear . T o use an HDMI cable, contact the PC manufactur er . INPUT 1 (Video) Input Name : Video Color System : A uto INPUT 2 (Component) : Component Color Decoding INPUT 3 (D-Sub 15) Input Name : D-Sub 15 Color Decoding : RGB INPUT 4 (D VI) Input Name : D VI Signal T ype : Video Video : Auto Input Setup 1/2 Exit PRO-141FD_PRO-101FD.book Page 52 M onday, May 12, 2008 3 :27 PM
53 En Use Other Equipment With Your Flat Panel Display 06 6.2.2 Apply Settings for a PC Connecting a PC to your flat panel disp lay requires specific settings. This se ction also explores the basic screen adjustments on the flat pan el display after applying initial settings for the PC. 1 ) Access INPUT 3( D -Sub1 5) through the Input Setup menu. 2 ) Select the desired item. D-sub15, Blu-Ray , DVD, DVR, VCR , Cable, Satellite , GAME or Computer for Input Name; RGB, Comp.1 (YCbCr) or Comp.2 (YPbPr) for Color Decoding. Auto is only available for Signal Format 3 ) Press EXIT to exit the menu. When connected to a PC, your flat pane l display automatically identifies the in put signal type. If the panel fail s to see the PC or the picture is unclear , use the Screen function to ad just the image . Automatic Image Position and Clock Adjustments When connected to a PC, the image po sition, clock phase and clock frequenc y can be adjusted. The Auto Setup option automa tically adjusts these setti ngs but the image position and clock can be adjusted manually too . This section co vers the auto matic se tup function and the fol lowing se ction explai ns how to man ually ad just positi ons and clock. T h e A V s o u r c e d e v i c e m u s t b e c o n n e c t e d t o t h e f l a t p a n e l d i s p l a y a n d t u r n e d o n f o r t h i s o p t i o n t o w o r k . T o a c t i v a t e Auto Setup, follow the direct ions belo w . 1 ) Access Auto Setup through the Screen menu. The functi on begins as soon as the selection is m ade . However , depending on the image, the position may not change after adjust ment. 2 ) Press HOME MENU to exit the menu. Note: This function is unavailable when the PC is connected t hrough the HDMI terminal. When Auto Setup finishes, the message Ã¢ÂÂ Auto Setup Complet edÃ¢ÂÂ appears on screen. However , if the setup fails to adjust the image, the message still appears if other fa ctors affec t the change. Auto Setup may fail with a PC image composed of similar patterns or a monochrome picture. If Auto Setup fails to correct the image positioning and clock, change the PC image an d tr y again. Manual Image Position and Clock Adjustments Usually Auto Setup for a PC is the bes t practice for adjusting th e image position , clock phase and cl ock frequency . However , to personally optimize th e screen, follow the direct ions below . 1 ) Access H.Position, V.Position, Clock or Phase through the Screen menu. 2 ) Use the up/down arrow buttons ( Ã¯ÂÂ©/Ã¯ÂÂª ) to adjust the option. H .P o sition , V .P osition , Clock and Phase also accept the left/right arrows ( Ã¯ÂÂ«/Ã¯ÂÂ¬ ) for changes. 3 ) Press HOME MENU to exit the menu. Option Description H .P osition adjusts the horizontal posi tion of an image V .P osition adjusts the vertical position of an image Clock adjust s an image when jitter appears Phase adjusts an image when jittered or low-contrast characters, etc. appear PRO-141FD_PRO-101FD.book Page 53 M onday, May 12, 2008 3 :27 PM
54 En 06 Use Other Equipment With Your Flat Panel Display 6.3 Use HDMI Inputs High Definition Multimedia Interface (HDMI) is a communica tion method commonly used by digital and/ or high definition equipment. Y our flat panel displ ay Ã¢ÂÂs IN PUT 5, INPUT 6, INPUT 7, IN PUT 8 are HDMI terminals for incoming digital video signals. The flat panel display su pports KU R O LINK func tions so that w hen a p iece of equipment is connected, the panel can control the equipment. T o use an HDMI terminal, specify the video signal types being sent from the connecte d equipment. F or signal types, see the operating ma nual(s) that came with the equipment. One of the benefits of using your flat panel display to co ntrol other equipment is the support of Deep Color . Deep Color is the color depth that describes the number of bits used to represent the color of a single pixel in a bitm apped image. Besides the conventional RGB/YCbCr16bit/20bit/24b it signals, the flat panel dis play also supports RGB/ YCbCr30bit/36bit signals. This feature enables finer color reproduction when connecting a device that supp orts Deep Color signals (HDMI1.3 Deep Color). The color depth appear s on the InfoBanner if a program supports Deep Color . With INPUT 5 through INPUT 8 selected, the color depth also appears on the Display screen. When connecting a PC to one of the pa nelÃ¢ÂÂs HDMI inputs, use an HDMI-complia nt PC or video card. F or a PC or AV equipment that h as a DVI outpu t termina l, use IN PUT 4 on yo ur flat panel disp lay . In this case, u se only a D VI- D24 (digital) for connections (see page 17). 6.3.1 Enter an HDMI Input Name T o enter an input name for each piece of equipment connected through HDM I, follow the d irections bel ow . 1 ) Select the Input for the connected equipment. P ress the INPUT button (remote control or panel) until the correct input is sh owing (INPUT 5, INPUT 6, INPUT 7, or INPUT 8). 2 ) Access Input Setup 2/2 through the Input Setup menu . 3 ) Select INPUT 5(HDMI 1), INPUT 6(HDMI 2), INPUT 7(HDMI 3) or INPUT 8(HDMI 4). 4 ) Select HDMI 1 through HDMI 4, Blu-Ray, DVD, DVR, VCR, Cable, Satellite, GAME or Computer . 5 ) Press EXIT to close the menu. INPUT 5 (HDMI 1) Input Name : HDMI 1 Signal T ype : Video Video : Auto Signal Format : Auto INPUT 6 (HDMI 2) Input Name : HDMI 2 Signal T ype : Video Video : Auto Signal Format : Auto INPUT 7 (HDMI 3) Input Name : HDMI 3 Signal T ype : Video Video : A uto Signal Format : A uto INPUT 8 (HDMI 4) Input Name : HDMI 4 Signal T ype : Video Video : A uto Signal Format : A uto Input Setup 2/2 Exit PRO-141FD_PRO-101FD.book Page 54 M onday, May 12, 2008 3 :27 PM
55 En Use Other Equipment With Your Flat Panel Display 06 6.3.2 Specify the HDMI Input Type T o select a signal type, follow the steps bel ow . 1 ) Select the Input for the connected equipment. Pr e s s t h e INPUT button (remote co ntrol or pane l) until the correct input is showing (INPUT 5, INPUT 6, INPUT 7, or INPUT 8). 2 ) Access Input Setup 2/2 through the Input Setup menu . 3 ) Select INPUT 5(HDMI 1), INPUT 6(HDMI 2 ), INPUT 7(HD MI 3) or INPUT 8(HDMI 4) . 4 ) Select Signal T ype from the submenu. 5 ) Select the appropriate option. 6 ) Press EXIT to exit the menu. In Video mode, the image is over-scann ed (enlarged) but the panel automatically switches to PC when receivin g computer signals. In PC mode, the image disp lays in full s ize fo r optimum image q uality . 6.3.3 Specify a Digital HDMI Signal Type F or the correct digital video signal type, check the oper ating manual that came with the other equipment . T o assign the type of digital signal,follow the steps below . 1 ) Access Input Setup 2/2 through the Input Setup menu . 2 ) Select INPUT 5(HDMI 1), INPUT 6(HDMI 2 ), INPUT 7(HD MI 3) or INPUT 8(HDMI 4). 3 ) Select Vid e o from the submenu. 4 ) Select the type of digital video signal recommended for the attached device. 5 ) Press EXIT to close the menu. If an image f ails to appear , specify another digital video si gnal type. T ype parameters ot her than Auto need to be checked for natural colorings. Option Description Vid e o us e ex c ep t wh e n a P C is connected (default) PC when a PC is connected to HDMI input terminal Type Description Auto automatica lly identifi es input digital signals 1 (YUV422) Digital Component Vide o signals (4:2:2) locked 2 (YUV444) Digital Component Vide o signals (4:4:4) locked 3 (RGB16-235) Digital RGB signals (16 to 235) locked 4 (RGB0-255) Digital RGB signals (0 to 255) locked Vid e o ( o ve r- s c a n) PC (under -scan) PRO-141FD_PRO-101FD.book Page 55 M onday, May 12, 2008 3 :27 PM
56 En 06 Use Other Equipment With Your Flat Panel Display 6.4 Control Equipment with the PanelÃ¢ÂÂs Remote Through HDMI Y our flat panel display Ã¢ÂÂs remote can control other equipm ent such as a P ioneer AV system , or BD/DVD player that supports the K URO LINK or HDMI Control functions feat ured in conventional Pioneer products. The K URO LINK functions include playback of content using an on-screen control panel. However , not all device operation s may be available through KU RO LINK. F or details, see the charts below . Note: Except for P ower OFF and Display Langua ge Setup functions, onl y a single HDMI terminal may be acti ve at a time. Control Function Controlled Equipment Function Description Playback of content Reco rd er Player P ressing PL A Y automatically selects the source and begi ns playback On-screen control Recorder Player Recorder/player operation controlled on-screen or with the panelÃ¢ÂÂs remote (play , stop, fast for ward/reverse, etc.) Display Language Setup Reco rd er Player Information on the display menu language transfers to the recorder or player (for details, see th e operation manual that came with the device) A V system control AV system Rec eiv er/amplifier operation also controlled with the panelÃ¢ÂÂs remote (input through th e HDMI port) P o wer ON R ecorder Player P anel turns On when a connected device is t urned On and sends image s to the panel Po w e r O F F R e c o r d e r Player A V system Connected device(s) turn Off w hen the panel is turned Off PRO-141FD_PRO-101FD.book Page 56 M onday, May 12, 2008 3 :27 PM
57 En Use Other Equipment With Your Flat Panel Display 06 The flat panel display Ã¢ÂÂs remote can co ntrol a maximum of two (2) re corders, two (2) playba ck devices, and one (1) AV s y s t e m a t a t i m e . T o select and use the various KU RO LINK functions for a connected P ioneer AV system, recorder , or player , use the panelÃ¢ÂÂs KURO LINK menu. T o access the KURO LINK menu, f ollow the step s below . 1 ) Press USER MENU on the remote. 2 ) Select KU RO L I NK from the main men u. Use the arrow buttons to high light an option then press ENTER . Note: P ressing KURO LINK on the remote also causes the KURO LINK menu to open. Use the following buttons to co ntrol functions such as di sc navigation on a record er or player . Ã¢ÂÂ¢ VOL /Ã¢ÂÂ (adjusts the volum e for an AV system) Ã¢ÂÂ¢ M U T I N G (turns off the sou nd while the video continues to play) Ã¢ÂÂ¢ Arrow buttons (navigates the menu screen) Ã¢ÂÂ¢ Col or buttons (Red, Green , Blue, Y ellow) (controls a BD player) Ã¢ÂÂ¢ TOOLS (assigns the code for a P ioneer BD player) Ã¢ÂÂ¢ E N T E R (activates the selected fun ction) Ã¢ÂÂ¢ R E T U R N (returns to the prev ious menu screen) Option Description Disc Navigator displays the player Ã¢ÂÂs or recorder Ã¢ÂÂs title list Timer REC (DVR) displays the recorder Ã¢ÂÂs program guide Timer REC List (DVR) displays the recorder Ã¢ÂÂs timer recording list Stop REC (DVR) stops the recorde r from recording CTRL Panel (AV-SYS) displays the AV systemÃ¢ÂÂs control panel Playback CTRL Panel displays the player Ã¢ÂÂs or recorder Ã¢ÂÂs control panel Disc Navigator Timer REC (D VR) Timer REC List (D VR) Stop REC (D VR) CTRL P anel(A V -SYS) Playbac k CTRL P anel 4 3 1 2 6 5 7 1 2 3 4 5 6 7 PRO-141FD_PRO-101FD.book Page 57 M onday, May 12, 2008 3 :27 PM
58 En 06 Use Other Equipment With Your Flat Panel Display T o connect a device for K URO LINK , follow the steps below . 1 ) T urn on th e flat pane l display an d all other eq uipmen t. 2 ) Confirm that the panelÃ¢ÂÂs Input Setting for KURO LINK Setting options comply with directions in the device(s)Ã¢ÂÂ operating instru ctions. 3 ) Confirm that the other equipment is set for KURO LINK . 4 ) Check that the au dio and video are playing b ack pr operly from the equipment c onnected through the HDMI terminal(s). 5 ) T urn Off the flat panel display . 6 ) P ause for a few seconds before turning the panel back on. 7 ) Veri f y that all equipment is functioning properly . T o select the device to control via KU RO LINK , follow the steps below . 1 ) Access KURO LINK Setting through the Control Setu p menu. 2 ) Select Input Setting from the submenu. 3 ) Select the desired Input (INPUT 5, INPUT 6, INPUT 7, or INPUT 8). 4 ) Press EXIT to exit the men u. If operating an HDMIÃ¢ÂÂsupported device using an HDMI port other than the te rminal selected in Input Setting, the system malfunctions. When connecting to an HDMI terminal other than that selected in Input Settin g, the equipment settings should block KU RO LINK functions. The KURO LINK menu is not selectabl e when the option Input Setting under the KURO LINK Setting menu is set to Off . The control menu changes to suit the ty pe of HDMI-compatible equipment . When adding, changing, or removing equipment from KURO LINK , refer to the sections below for instal lation notes and the supported commands. 6.4.1 Control an AV Sy stem When adding an A V System, connect th e unit be tween the panel an d any rec orders and/ or play ers. T o fun ction properly , your Audio/V ideo system manages the KURO LINK functions be tween the panel and any other connected equipment. P ower Off T est P ower On T est Input Setting : INPUT 5 P ower Off Control : Off P ower On Ready : Off Hold Sound Status : Off KURO LINK Setting PRO-141FD_PRO-101FD.book Page 58 M onday, May 12, 2008 3 :27 PM
59 En Use Other Equipment With Your Flat Panel Display 06 During playback, use the remote controlÃ¢ÂÂs up/down arro ws ( Ã¯ÂÂ©/Ã¯ÂÂª ) to c ycle through the surround so und options. Use the left/right arrows ( Ã¯ÂÂ«/ Ã¯ÂÂ¬ ) to cha nge the input. T o resume playback, return to the KURO LINK menu then select the function again. 6.4.2 Control a Recorder Pr e s s ENTER to start playback or p ress KURO LINK to return to the menu. This process also app lies to Players. Refer to the chart below for available commands. Note: Y ou can also use Ã¯ÂÂ¤ (Play), Ã¯ÂÂ§ (Stop), Ã¯ÂÂ¥ (P ause), Ã¯ÂÂ® (F ast Forward) and Ã¯ÂÂ (F ast Reverse) on the remote control to condu ct the same operat ions as the control menu buttons. 6.4.3 Contr ol a Player Pr e s s ENTER to start playback or press KURO LINK to return to the menu. This process also applies to Recorders. Refer to the chart below for available commands. Note: Y ou can also use Ã¯ÂÂ¤ (Play), Ã¯ÂÂ§ (Stop), Ã¯ÂÂ¥ (P ause), Ã¯ÂÂ® (F ast Forward) and Ã¯ÂÂ (F ast Reverse) on the remote control to condu ct the same operat ions as the control menu buttons. AV Systems 1 Cycles the surroun d mode in sequence 2 Switches the input source in reverse orde r 3 Switches the surround mode in rev erse order 4 Closes the screen to return to KURO LINK menu 5 Lists the connected equipment (model number/up to eight characte rs) 6 Switches the input source in sequence 7 Reserved/Voi d Recorders 1 Skips commercials 2 Fast reverse 3 Stops playback 4 Closes the screen to return to KURO LINK menu 5 Lists the connected equipment (model number/up to eight characte rs) 6 Fast forward 7 Starts playback Players 1 Displays the DVD/Blu-ray disc menu on the player 2 Fast reverse 3 Stops playback 4 Closes the screen to return to KURO LINK menu 5 Lists the connected equipment (model number/up to eight characte rs) 6 Fast forward 7 Starts playback Exit KURO LINK **** INPUT INPUT - SURROUND SURROUND- 3 1 2 4 5 7 6 Exit KURO LINK **** 3 1 2 4 5 7 6 Exit KURO LINK **** MENU 3 1 2 4 5 7 6 PRO-141FD_PRO-101FD.book Page 59 M onday, May 12, 2008 3 :27 PM
60 En 06 Use Other Equipment With Your Flat Panel Display 6.4.4 Add an AV Amp or a BD Player T o add an A V amp and/or a BD Playe r , refer to the appro priate cabling diagram b elow . A V Amp & BD Player BD Player only Rea r v ie w HDMI compliant cable (HDMI cable having the HDMI mark) BD player AV a m p HDMI compliant cable (HDMI cable having the HDMI mark) Rea r vi e w BD player PRO-141FD_PRO-101FD.book Page 60 M onday, May 12, 2008 3 :27 PM
61 En Use Other Equipment With Your Flat Panel Display 06 6.5 Specific KURO LINK Commands When using HDMI e quipment with your fl at panel displa y , some options include wh en to power the panel and ways to turn o ther devices or feat ures On and Off . This sectio n provides steps for com monly desired changes. 6.5.1 Play Source Sound Using an HDMI Command When sound i s coming from a P ioneer A V System throug h the flat panel display , pl acing the panel in Standby causes the sound to stop. T o have the sound continue when the flat pane l disp lay turns On, follow the steps below . 1 ) Access KURO LINK Setting through the Control Setup menu . 2 ) Select Hold Sound Status from the submenu. 3 ) Select On to allow sound from an A V System to play when the pane l is in Standb y . 4 ) Press EXIT to exit the menu. 6.5.2 Turn OFF the Power With an HDMI Command The Ã¢ÂÂP ower Off ControlÃ¢ÂÂ function is va lid for the devices connected to any of the panelÃ¢ÂÂs HDMI ports. T o power off a connected device when the fl at panel disp lay is turned Off , follow the steps below . 1 ) Access KURO LINK Setting through the Control Setup menu. 2 ) Select P ower Off Control from the submenu. 3 ) Select On to allow the panel to power off the connected equipment. 4 ) Press EXIT to exit the menu. 6.5.3 Turn ON the Power With an HDMI Command The panel ships from the factor y with the P ower On command activated. If this fe ature is turned off in e rror , it can be reactivated. T o power on the flat panel display au toma tically when a conn ected P ion eer recorder or player is turned On (im ages are sent ), follow the steps below . 1 ) Access KURO LINK Setting through the Control Setup menu . 2 ) Select Po w e r O n R e a d y from the submenu. 3 ) Select On to have anot her device power - on the panel. 4 ) Press EXIT to exit the menu. PRO-141FD_PRO-101FD.book Page 61 M onday, May 12, 2008 3 :27 PM
62 En 06 Use Other Equipment With Your Flat Panel Display 6.5.4 Test the Pow er Control (On/Off) Y our flat panel display provi des the KURO LINK option to test whether equipment co nnected to the panel via an HDMI port can power up. Each device must be properly assigned to an Input for this function to p er form. T o confirm that the P ower On/O ff control fu nction is work ing, foll ow the steps below . 1 ) Access KUL O LINK Set ting through the Control Setup menu . 2 ) Select a test option ( Po w e r O n T e s t or P ower Off T est ) from the submen u. A list containin g all HDMI connected equipment appears. 3 ) Select a piece of equipment from the list to begin the test. 4 ) Repeat th is process to test other equipment from the list. 5 ) Press EXIT to exit the menu when all testing is complete. If the P ower On/Off T est fails, check th e connection points and the settings. 6.6 Connect a Game Console or Camcorder Y our flat panel display supplies dire ct connection s for a game console, ca mcorder , or other Audio/Visual (A V) equipment through INPUT 1. T o watch an image co ming from a game console or camcorder , press INPUT 1 on the remote control or repeatedly press INPUT on the panel to select INPUT 1. F or details on game console settings, refer to Ã¢ÂÂ2.3 Conn ect to Ot h er Devices (DVR , Receiver , BDR, etc.)Ã¢ÂÂ and to Ã¢ÂÂ5.1.4 Set the P a nel to Recognize a Game Console.Ã¢ÂÂ Use the connection type specified by th e equipment. Connect equipme nt only to terminals that are actually to be used. 6.7 Use the IR REPEATER OUT Connecting control cables between the flat panel display an d other P ioneer equipment allow s you to operate the connected equipmen t via commands from the remote control . This function is helpful when controlling P i oneer equipment from other Pioneer equipment. PRO-141FD_PRO-101FD.book Page 62 M onday, May 12, 2008 3 :27 PM
63 En Use Other Equipment With Your Flat Panel Display 06 6.8 Connect to a Network Connecting y our flat panel display t o a home network or local area network (LAN) cause s the panel to functi on as a ser ver . T o run the panel on a network, see the diagra m below for connections. Af ter connection to a network, apply initial settings described i n the following sections. Caution: Ã¢ÂÂ¢ With the flat panel di splay, browsing Internet we bsites and sending/receiving E-mails are unavailable. Ã¢ÂÂ¢ Broadcasts and on-line video ser vices via the Intern et are unavailable. Ã¢ÂÂ¢ Purchase commerciall y available connection devi ces and cables as needed. Ã¢ÂÂ¢ Combining different communication brand tools with some service pr oviders, or different modem and broadband router brands may cause communication failures or requir e additional services f rom your service provider. Ã¢ÂÂ¢ Connecting to a network may requir e additional settings on your PC. Ã¢ÂÂ¢ After connection to a netw ork, enter correct settings. Ã¢ÂÂ¢ Pioneer is not responsible for any damage due to erro neous operations or unsucce ssful E-mail transmissions. Using a LAN Ã¢ÂÂ¢ Use 10BASE-T or 100BASE-TX for a broadband router or hub. Ã¢ÂÂ¢ Do not connect your flat panel display directly to the Internet. Connect the panel through a Firewall, leaving only necessary ports open. Ã¢ÂÂ¢ Do not connect a modular telephone cable to the LAN (10BASE-T/100BASE-TX) terminal. Doing so can cause a malfunction. Ã¢ÂÂ¢ Required equipment and connection methods may differ, depending on the communicatio n and/or service provider. Ã¢ÂÂ Use devices such as an ADSL modem, broad ban d router , hub and splitter as specified by the communicatio n and/or ser vice provider . Also refer to the instruc tion manual that came with the devi ce. Ã¢ÂÂ Settings are unavail able for a br oadband ro uter or an ADSL modem with a broadband router function . Ã¢ÂÂ¢ When communicating through a LAN, da ta encryption is unavai lable thro ugh your pane l. When accessing the Internet, run the display on a virtual private netw ork (VPN) or other protec ted communication network environment. Ã¢ÂÂ¢ Do not send a command to both the RS-232C and LAN terminals at the same time . Doing so can cause the display to receive the command erroneously. About ADSL Modems Ã¢ÂÂ¢ Utilizing bridgi ng for an ADSL modem requires a separate broadband router. Ã¢ÂÂ¢ For details on an ADSL modem, consult yo ur communication and/or service provider. PC 2 PC 1 Ethernet hub (Router w ith hub function) Straight-through cable Rear view Cross-over cable PC Rear view PRO-141FD_PRO-101FD.book Page 63 M onday, May 12, 2 008 3:27 PM
64 En 06 Use Other Equipment With Your Flat Panel Display 6.8.1 IP Control Setting T o apply the IP Co ntrol Setting , follow the directions below . 1 ) Access IP Control Setting through the Control Setup menu . 2 ) Select IP Control from the IP Control Setting menu. 3 ) Select Enable from the IP Control menu. Note: The default IP Control menu is Dis able. Confirm the IP Address Enter DHCP , IP Address, Subnet Mask, Defa ult Gateway and LED. 1 ) Access IP Control Setting through the Control Setup menu . 2 ) Select DHCP from the IP Control Setting menu. 3 ) Select On or Off from the submenu. If you select On, an IP Ad dre ss is automatically acquired. If the panel fails to assign the IP Addr ess or if you want to obtain different addres ses, sel ect Off in Ste p 3 then enter an IP Address and Subnet Mask. 4 ) Press RETURN to make your selection. 5 ) Select LED from the IP Control Setti ng menu. 6 ) Select On or Off from the submenu. Selecting On causes the L AN terminal indicator to light while in use. 7 ) Press EXIT to exit the men u. IP Control Setting IP Control : Disable DHCP : Off IP Address Subnet Mask Default Gatewa y MAC Address LED : On KURO LINK Setting Input Setting : Off P ower Off Control : Off P ower On Ready : Off Hold Sound Status : Off P ower On T est : Off P ower Off T est : Off Serial Setting ID No. Set : All Baud Rate : 9600bps Control Setup Exit PRO-141FD_PRO-101FD.book Page 64 M onday, May 12, 2008 3 :27 PM
65 En Use Other Equipment With Your Flat Panel Display 06 6.8.2 Use the Web Control System Y ou can ac cess and control the panel from the PC using a web browser . T o use this option, follo w the directions below . Display Settings When switching browser screens, find the needed screen from th e list on the lef t. Do not use browser bu ttons and menus, such as P revious P age, Next P age, History and Bookmark. Using these b uttons and menus to switch the screens causes an imperf ect screen to appe ar . T o select a browser , follow the steps below . 1 ) Enter the obtained IP Address in the browser Ã¢ÂÂs address box. 2 ) Enter Ã¢ÂÂadminÃ¢ÂÂ on the password entry screen. 3 ) Click Network to begin entering settings. ;0 4 ) E nter information in the following fields: Ã¢ÂÂ¢N A M E Ã¢ÂÂ¢L o c a t i o n Ã¢ÂÂ¢ Installation date Ã¢ÂÂ¢ LED (On/Off) Note: T o ch ange entries other than NAME, L ocation and In stallation date, close the browser then re-open it. T o ch ange entries for IP Address, Subnet Mask or Default Gateway , close the browser , change the PC network settings then re-open it. Ã¢ÂÂ¢ F or browsing, use the Internet Explorer . Using any other web browser can cause a distorted image or imper fect contents to appear . Ã¢ÂÂ¢ F rom the Internet Explorer Ã¢ÂÂT oolsÃ¢ÂÂ menu, click Ã¢ÂÂInternet OptionsÃ¢ÂÂ to open the Genera l tab. Click Ã¢ÂÂSettingsÃ¢ÂÂ¦Ã¢ÂÂ in the Ã¢ÂÂT emporar y Internet Fi lesÃ¢ÂÂ section to select Ã¢ÂÂEvery time you start Internet Explorer Ã¢ÂÂ under Ã¢ÂÂCheck for newer versions of stored pag es:Ã¢ÂÂ. Model : ****** Name : ****** Location : ****** ****** To p Picture Terminal Functions Network E-mail ISF Detail Settings Network Settings Network Web control system Set NAME : Location : Installation date : IP address : Sub net mask : Default gateway : TCP Control Port : UDP Control Port : DHCP : ON OFF TCP Connection limit : OFF ON ... minutes LED : ON OFF MAC address : 00:00:00:00:00:00 5 PRO-141FD_PRO-101FD.book Page 65 M onday, May 12, 2008 3 :27 PM
66 En 06 Use Other Equipment With Your Flat Panel Display Ã¢ÂÂVirtualÃ¢ÂÂ Remote Control Settings 1 ) Enter your IP Address in the browser Ã¢ÂÂs address box. 2 ) Enter Ã¢ÂÂadminÃ¢ÂÂ on the password entry screen. The V irtual R emote Cont rol appears on screen. 3 ) Click the desired butt on to execute a command. Picture Adjustments Click Pi c t u r e to display the pictur e adjustment screen . Note: While operating on the web screen , using the remote or button s on the flat pa nel di splay to directly control the panel can cause the operational st atus on the web screen to differ fr om the pan el status. T o find the needed screen on the panel, select the appropriate me nu on the left. Model : ****** Name : ****** Location : ****** ****** To p TOP : V ir tual Remote Picture Terminal Functions Network E-mail ISF No Frame >> Detail Settings Network Settings INPUT1 INPUT2 INPUT3 ON STANDBY INPUT4 INPUT5 INPUT6 INPUT7 INPUT8 SPLIT SUB INPUT SWAP PIP SHIFT AV SELECTION AUTO SETUP FREEZE SCREEN SIZE DISPLAY EX IT USER MENU HOME MENU RE T U R N Web control system UP ENTER DOWN LEFT RIGHT Model : ****** Message : ERR MSG Power : Input : AV Selection : Picture : Color Temp. : White Balance : Gamma : Blue only mode : Screen size : Detail Adjust Contrast Brightness Color Tint Sharpness R.High G.High B.High R.Low G. Low B. Low Name : ****** Location : ****** ****** To p Picture Terminal Functions Network E-mail ISF Detail Settings Network Settings STANDARD DYNAMIC PURE SPORT GAME MOVIE isf-DAY USER isf-NIGHT isf-AUTO ON STANDBY OPTIMUM 1 2 3 4 5 6 7 8 Picture Web control system 40 Set 3 Set 0 Set 0 Set 0 Set 0 Set 0 Set 0 Set 0 Set 0 Set Reset Auto Setup 0 Set 0 Set Manual Set Off Set Cinema 14:9 Set PRO-141FD_PRO-101FD.book Page 66 M onday, May 12, 2008 3 :27 PM
67 En Use Other Equipment With Your Flat Panel Display 06 Input Setting Click Te r m i n a l to display the input setting screen. Note: While operating on the web screen , usin g the remote or buttons on the flat panel display to directly control the panel can cause the operational status on the web sc reen to differ f rom the panel status. T o find the needed screen on the panel, select the ap propriate menu on the left. Function Setting Click Fu n c t i o n s to display the func tion setting screen . Note: While operating on the web screen , usin g the remote or buttons on the flat panel display to directly control the panel can cause the operational status on the web sc reen to differ f rom the panel status. T o find the needed screen on the panel, select the ap propriate menu on the left. Model : ****** Name : ****** Location : ****** ****** To p Picture Terminal Functions Network E-mail ISF Detail Settings Network Settings Power : INPUT SETUP : ON STANDBY T er minal Web control system Set INPUT 1 : Video INPUT 2 : Compornent INPUT 3 : D-sub 15 INPUT 4 : DVI INPUT 5 : HDMI 1 INPUT 6 : INPUT 7 : INPUT 8 : HDMI 4 Color System : Auto Color D e co di n g : Comp.1(YCbc Color D e co di n g : RGB Signal Type : PC Signal Type : PC Signal Type : PC Signal Type : PC Signal Type : PC Video : AUTO Video : AUTO Video : AUTO Video : AUTO Video : AUTO HDMI 2 HDMI 3 Model : ****** Name : ****** Location : ****** ****** To p Picture Terminal Functions Network E-mail ISF Detail Settings Network Settings Power : Option setting ON STANDBY Functions Web control system Set Energy save : Standard Set Power management : Off Set No signal off : Disable Set No operation off : Disable Set Room light sensor : Off KURO LINK setting Set Input Setting : Off Set Power off control : Off Set Power on ready : Off Set Hold sound status : Off PRO-141FD_PRO-101FD.book Page 67 M onday, May 12, 2008 3 :27 PM
68 En 06 Use Other Equipment With Your Flat Panel Display Event Notification Y our flat panel display can provide E-mail notifica tion if there is a system error or malfunction. Note: Y our flat panel display does not have a function that determines the name of network computer within the Internet. Enter your mail server Ã¢ÂÂs IP Address in the Ma il ser ver (SMTP) box. If th e IP Address is no w known, use such a search program as the Ã¢ÂÂnslookupÃ¢ÂÂ on your PC. Option Description Sender add ress ent ers the sen der Ã¢ÂÂs add ress Mail server (SMTP) enters the sender server Ã¢ÂÂs IP address Authentication sets whether to authenticate when sendin g an E- mail (P op before SMT P is set for the authentication method) ID enters an authentication ID P assword enters a password for authentication Received address (1) - (3) enters the recipien t address Event option P ower down sends an E-mail when the fai l-safe function is activated due to a panel error that ma y cause a malfunction Shut down sends an E-ma il when the protection fu nction turns the panel off automatically Usage time sends an E-mail at a specified interval (ever y 500 hours if set to Ã¢ÂÂ500Ã¢ÂÂ) Input change sends an E-mail when the input mod e changes Loss of input signal sends an E-ma il when no input signal appears P ower toggle sends an E-mail when the power status ch anges Model : ****** Name : ****** Location : ****** ****** To p Picture Terminal Functions Network E-mail ISF Detail Settings Network Settings E-mail Web control system Set TEST MAIL Sender address : Mail server(SMTP) : Event option : Received address (1) : Received address (2) : Received address (3) : Password : ID : Authentication : ON OFF Power down ... Panel error Shut down ... Temp.,speaker and fan error Input change Loss of input signal Power toggle Usage time ... Every hours 1000 PRO-141FD_PRO-101FD.book Page 68 M onday, May 12, 2008 3 :27 PM
69 En Use Other Equipment With Your Flat Panel Display 06 6.9 Assign a Serial Number 6.9.1 Assign an ID N umber This section describes how to enter th e required ID number for co ntrolling and adjusting multip le panels through a single PC. T o assign the ID Number , follow the directions below . 1 ) Access Serial Setting through the Control Setup menu . 2 ) Select ID No. Set from the Serial Setting menu. 3 ) Select All or 00H-FFH from the s ubmenu. Note: This setting applies to all input sources. Parameter Description 00H-FFH sets an ID Number All does not set an ID Number C:\> nslookup Server: xxx.xxx.xxx.com Current name server Adress: yyy.yyy.yyy.yyy > mailsv.aaa.com Mail server searched for Server: xxx.xxx.xxx.com Current name server Adress: yyy.yyy.yyy.yyy Non-aurthoritative answer: Name: mailsv.aaa.com Adress: zzz.zzz.zzz.zzz Server: IP Address for mailsv.aaa.com Sample MS-DOS search screen using Ã¢ÂÂnslookupÃ¢ÂÂ IP Control Setting DHCP : On IP Control : Disable IP Address Subnet Mask P ower On T est P ower Off T est P ower On Ready : Off Hold Sound Status : Off Input Setting : Off P ower Off Control : Off Default Gate way LED : On MAC Address KURO LINK Setting Serial Setting ID No.Set : All Baud Rate : 9600bps Control Setup Exit ID No .Set All PRO-141FD_PRO-101FD.book Page 69 M onday, May 12, 2008 3 :27 PM
70 En 06 Use Other Equipment With Your Flat Panel Display 6.9.2 Assign a Baud Rate This section describes how to enter the RS-232C transmi ssion speed (baud rate) when controlling or adjusting the panel using a PC. (Use this opti on onl y when m aking p icture adjustme nt s for a specific device(s) connected to the RS-232C terminal.) The baud rate can be set to 1200bps, 2400bp s, 4800bps, 9600bps, 19200bps or 38400bps. T o enter a rate, fo llow the directions below . 1 ) Access Serial Setting through the Control Setup menu . 2 ) Select Baud Rate from the Serial Setting men u. 3 ) Select the desired rate from the submenu. The factor y default setting is 9600bps. Note: This se tting ap plies to all input sources. 6.10 Select the Integrator Mode Integrator Mode provides alternative options when us ing specific functions/setti ngs an d picture adjustment menus. Notes: Integrator Mode is only available in English. After en tering the Integrator Mode , the following options on the Home Menu are reset to th e factor y defaults: Ã¢ÂÂ¢P i c t u r e Ã¢ÂÂ¢S c r e e n After entering the Integr ator Mode, the following options remain unchang ed: Ã¢ÂÂ¢P o w e r C o n t r o l Ã¢ÂÂ¢O p t i o n Ã¢ÂÂ¢ Input Setup Ã¢ÂÂ¢ Control Setup T o switch to the Integrator Mode, follow the directions below . 1 ) Press INPUT to select the desired input. 2 ) Press DISPLAY to reveal current settings. Status info rmation on the selected input appears on screen. 1200bps 2400bps 4800bps 9600bps 19200bps 38400bps Baud Rate - - - FULL Standard Component INPUT2 PRO-141FD_PRO-101FD.book Page 70 M onday, May 12, 2008 3 :27 PM
71 En Use Other Equipment With Your Flat Panel Display 06 3 ) Press and hold DISPLAY for at least three seconds while th e screen in Step 2 remains visible. Only input signals appear . 4 ) Press HOME MENU while the screen in Step 3 remains vi sible but do not hold the button down. The panel switches to Integrato r Mode. Note: P ressing and holding or pressing HOME MENU long causes the panel to remain in User Mode. 6.10.1 Explore the Inte grator Mode Menus Picture Preset Use this option to preset the Pictur e adjustment values for the Home Menu. Studio Mode In addition to normal adjustment values, the panel al so provides a separate professional adjustment mode optimum for retake at a TV studio (Studio). Notes: This settin g applies to all input so urces. Entering Monotone Mode, A V Selection or Blue On ly Mode is unavailable while i n Studio Mode. Monotone Mode Monotone Mode cuts the video signalÃ¢ÂÂs color components so that images appear using only lumin ance sig nals. Notes: This settin g applies to all input so urces. Entering Studio Mod e, AV Selec tion or P icture P reset is unavailable wh ile in Monotone Mode. Parameter Description On switches to the Studio Mode Off* No effect *F actor y default Parameter Description On switches to the Monotone Mode Off* No effect *F actor y default INPUT2 Picture Studio Mode : Off Picture Preset Monotone Mode : Off Drive Mode : 1 FRC Mode : Default T ranslucent : Off Banner PIP : Off Mirror Mode : Off Banner PIP P ower On Mode P ower On Mode (Input) Input : Last Option F an Control : A uto OSD Display : On Netw or k ID Beacon : Off IP Control Look : Off F actor y Default INTEGRA T OR MENU Exit PRO-141FD_PRO-101FD.book Page 71 M onday, May 12, 2008 3 :27 PM
72 En 06 Use Other Equipment With Your Flat Panel Display Drive Mode This option o ptimizes the picture qualit y depending on the content (refer to Ã¢ÂÂ5 .3.10 Adjust Color SignalsÃ¢ÂÂ for more information). Note: Drive Mode i s available only for input video signals. FRC Mode The FRC option allows switching the frame rate conversion. Note: FRC Mode is available only for input PC signals. Fan Control This option s witches th e control met hod for th e rear cooling fan of the flat panel display . The Max setting is effective fo r special high-temperature installations. Ho we ver , since the fan noi se increa ses, the effect on the surroundin g area should be taken into considerati on. On-screen Display This option sets the menu display to On or Off . Note: This se tting ap plies to all input sources. Parameter Description Default* does not switch the fram e rate conversion Sync sw itches the frame rate conversion *F act or y defaul t Parameter Description Auto* automat ically controls using an interna l temperature sensor Max f or maximum rpm (Auto Control: Off) *F act or y defaul t Parameter Description On* displays the current menu when pressin g DISPLA Y Off does not display the screen when: Ã¢ÂÂ¢ pressing DISPLAY or AV SELECTION Ã¢ÂÂ¢ switching the inpu t source Ã¢ÂÂ¢ adjusting the volume (Screen components suc h as Home Menu, User Menu and messages remain on the screen even when setting the On -screen Display option to Off .) *F act or y defaul t PRO-141FD_PRO-101FD.book Page 72 M onday, May 12, 2008 3 :27 PM
73 En Use Other Equipment With Your Flat Panel Display 06 Power On Mode This option automatically selects the i nput when the panel is turned On. Note: This setting applies to all input sources. Mirror Mode This option reverses the im age di splayed on the screen. Note: This setting applies to all input sources. Banner PIP Use the Banner PIP option to adjust the translucence rate and di splay po sitions of the small wi ndow i n P -i n-P mode. Ã¢ÂÂ¢ T ranslu cent: adjusts the translucent rate of the small screen in P -in-P mode between Off and 80%. If the percentage increases, th e tran slucent rate also increases. Ã¢ÂÂ¢ Banner PIP : adjusts the display position s of the small screen in P -in-P mode Ã¢ÂÂ¢ Banner Input: determines the input sign al for the small w indow in P -in-P mode Parameter Description INPUT 1 through INPUT 8 displays the selected input Last* displays the last input selected *F actor y default Parameter Description On reverses the image Off* does not reverse the image *F actor y default Parameter Description T ranslucent On adjusts the tra nslucent rate Off* No effect Banner PIP Off* N o effect Bottom 1 through 3 adjusts display positi ons Mid Low/High To p 1 t h r o u g h 3 Banner Input INPUT 3* throug h 8 determines the input signal *F actor y default PRO-141FD_PRO-101FD.book Page 73 M onday, May 12, 2008 3 :27 PM
74 En 06 Use Other Equipment With Your Flat Panel Display Note: The high er the reso lution bec omes on th e main scree n image , the lowe r the contrast b ecomes on the smal l window image . Signals that support Banner PIP are XGA 60 Hz and WXGA 60 Hz. IP Control Lock This locks or unlocks the IP Control settings. Note: This se tting ap plies to all input sources. Network ID Beacon This option authenticates the connection betwe en the spec ified eq uipment an d the flat pane l display. Parameter Description On locks th e IP Control settings Off* No effect *F act or y defaul t Parameter Description On applies the Network ID Beacon Off* No effect *F act or y defaul t MID HIGH MID LOW 270 540 810 1080 1920 T OP 1 T OP 2 T OP 3 BO TTOM 1 BO TTOM 2 BO TTOM 3 The Banner sub-screen option uses only the top 1/4 of a PC signal input. When adding a picture or text, the image or text must be placed in the top 1/4 area. PRO-141FD_PRO-101FD.book Page 74 M onday, May 12, 2008 3 :27 PM
75 En Helpful Information 07 7 Helpful Inform ation This chapter includes answers to some common question s and provides cautions and warnings for both pane l installation and usage. If you need further assistance, p lease contact us and give us the chance to correct any issues you are experiencing. Thank you again for buying P ioneer! 7.1 Frequently Asked Questions (FAQs) This section answers some of the questions received by ou r Support staff members. If your question is not here or you would like more information please see the P ioneer website for more F AQs (www .pioneerelec tronics.com) about your specific mo del or our flat pane l displays in general. Why wonÃ¢ÂÂt the remote control buttons control my flat panel display? If you select a mode other than MONITOR on the remote control, your flat panel display cannot receive the commands. P ress the SELECT button to toggle the modes until the MONITOR indicator lights. Why do I have to move closer to the panel to use the remote control? W eak batteries in the remote control can cause commun icati on to fail. T r y moving closer to the panel and attempt to control the panel with the remote. If the panel respon ds then change the batteries. If moving cl oser has no effect on t he panel, chec k the surrou ndi ngs for objects that might be blocking the signal. Also consider if other equipment that use remote controls have been added to the area around the panel. Objects and other IR signals can disrupt the remote . How can I protect t he remote so it holds up longer? There are se veral ways to p rotect you r remote contro l. Do not leave the remote sittin g in direct sunlight as thi s can warp or deform the case. Avoid spilling liquids on th e remote but if this happens, dr y it immediately . If necessar y , remove the batteries and allo w the unit to dr y completely before attempting to use it again. Areas with high humidity can also cause damage. Another issue that can affect the remote control is a leaking batter y . The chemicals from a leaky battery can discolor or damage the re mote. If there is visible leak age in a batter y , remove both batteries immediately and carefully wipe the batter y compartment clean. Replace both batteries with fresh ones. Can the signal from my panelÃ¢ÂÂs remote mess up other audio/video equipment? The flat panel display emits very weak in frared rays from its screen . If there is other equipment close by that also uses a remote control such as a DVR or stereo system , it may not receive command s f rom its remote control properly . T r y moving the equipment fart her away from the flat panel display . Note: The strength of infrared rays emitted from the pa nel differs as the picture changes on the screen. Why does the picture se em to dim when I leave a picture on the screen? When still images (such as photos and com puter images) stay on the screen for an extended pe riod of ti me, the screen slightly dims. This function protects the panel from damage by automatically adjusting the s creen brightness. The screen dims w hen a still imag e is detected for approximately three minutes. Why wonÃ¢ÂÂt my Pioneer flat panel display turn on? It may be that your remote has failing batteries or has been damaged. Check the power cord connection at the wall and on the back of the panel. Also tr y pressing a on you panel. PRO-141FD_PRO-101FD.book Page 75 M onday, May 12, 2008 3 :27 PM
76 En 07 Helpful Information Why does the blue power light on my flat panel display blink? The panelÃ¢ÂÂs internal protection circuit may have been activate d for so me reason. F irst turn the panelÃ¢ÂÂs a off , wait one (1) or m ore minutes, then turn it ba ck on. If the ligh t still blinks, unplug the power cord from the outlet. Plug in the panel again af ter one to two minutes. If this fails to solve the prob lem, contact your dealer or P ioneer Customer Support (see back cover). What can I do to prevent image retention or burn-in? Burn-in or Image R etention is a side effect of plasma technology . Af ter an image remains on the display for an extended time period, when the image chan ges or the unit is turned off , a fain t afterimage or ghost of the original picture may re main. Cont inuing to play vid eo or leaving the uni t turned off for a l ength of time can c lear the afterimage. W e recommend the following s teps and settings to prevent image retention or burn-in. Ã¢ÂÂ¢ Set Long Life Settings to On. Ã¢ÂÂ¢ Do not leave still images on screen. How do I clean my flat panel display? T o clean the screen sur face, gently wipe it with the su ppli ed dr y cloth. R ubbing hard on the screen can scratch the special film coating. Use a clean so ft cloth (cotton or flan nel, for example) for the cabinet. F or details on cleaning, refer to Ã¢ÂÂ7. 2 Cleaning Methods.Ã¢ÂÂ 7.2 Cleaning Methods Before cleaning yo ur flat panel display , unplug the powe r cord from the outlet. When cleaning the screen or the gl ossy front bezel, gently wipe with a clean, dr y cloth such as the supplied cleaning cloth or a similar type of sof t cloth (e.g., co tton, flannel, etc.). Avoid a wet or damp cloth as th at can let moisture seep into the panel. A dusty or rough-textured cloth (or if you rub t oo ha rd), can scratch sur faces. Note: Do not use liquid cleaners or ae rosol cleaners on the screen . The chassis o r cabinet of the panel i s mostly composed of plastic. Do not use chemicals such as benzene or paint thinner to clean the cabinet. These ch emicals ca n mar the finish or c ause other deterioration . When cleaning the cabinet, use the same type of cloth and method as described for th e front bezel. Note: Do not affix labels, tapes, etc. to an y visible location on the flat panel display . Adhesives can discolor or mar the panel sur faces. PRO-141FD_PRO-101FD.book Page 76 M onday, May 12, 2008 3 :27 PM
77 En Helpful Information 07 7.3 Troubleshooting & Service Information General Issue Possible Solution s No power Ã¢ÂÂ¢ Check the co nnection s eating at the wall and panel. Ã¢ÂÂ¢ See if the pan elÃ¢ÂÂs ma in power sw itch is t urned ON. Ã¢ÂÂ¢ Confirm that the remot e is set to MONITOR. If the panel indicator lights red, press MONITOR ( a) on the remote control or the STANDBY/ON button on the flat panel display . P ower suddenly turns off Ã¢ÂÂ¢ Chec k the power control setting. Ã¢ÂÂ¢ See if the panelÃ¢ÂÂs in ternal temp erature ha s increas ed. Clean the vents or remove an y blocking objects. P anel does not operate Ã¢ÂÂ¢ External influe nces such as voltage ma lfunction, static electr ici ty, etc., may cause improper operation. Unplug the panel from the wa ll and leave it for two or mo re minutes. R econnect and attempt to operate the panel once again. Remote control does not operate Ã¢ÂÂ¢ Check if display power is off . Press the button when the Power On and STANDBY indicators are off. Ã¢ÂÂ¢ Confirm that the mode is set to MONITOR. Ã¢ÂÂ¢ Examine the remote control s ensor on the panel for obstructions that c ould block the signal. Ã¢ÂÂ¢ Check that the remoteÃ¢ÂÂs batteries are instal led properly and hold a ch ange. Replace with new batteries to verify . Ã¢ÂÂ¢ Consider changes in lighti ng such as strong er or new light sources that m ay wash out the signal. Picture Issue Possible Solution s No picture Ã¢ÂÂ¢ Check the pict ure adjustment set tings. Reset to default values if necessar y . Ã¢ÂÂ¢ Confirm that the connec ted equipm ent is install ed and programm ed properly. Ã¢ÂÂ¢ If viewing an image from a PC, conf irm that the sign al is compatible. Screen appears dark Ã¢ÂÂ¢ Check for an y obstacles in front of the R oom Light Sensor. Odd coloring an d shades or misaligned images Ã¢ÂÂ¢ Review the room lighting for rece nt changes or different na tural lighting sourc es from windows or do orways. Ã¢ÂÂ¢ Check the picture ton e, adjust as necessary. Pi c t u r e i s c u t o f f o r r u n s off screen Ã¢ÂÂ¢ Check the screen size fo r the current input source. Ã¢ÂÂ¢ Confirm that the posit ion of the picture is centered. Brightness and color tone on the sides differ from the center Ã¢ÂÂ¢ If images in 4:3 mode or letterbox images are displayed for lo ng periods or for shorter periods over se veral days, an af ter-image may remain due to burning. W atch images in F ull screen as mu ch as possible to avoid this issue. Ã¢ÂÂ¢ Change t he Brightness Sync. settin g to Auto . This function adjusts the brightness of the gray side masks for the brightness of the main image. Ã¢ÂÂ¢ Use the Long Life Settings func tion (see Ã¢ÂÂ4.2.1 Extend Your Panel LifeÃ¢ÂÂ) PRO-141FD_PRO-101FD.book Page 77 M onday, May 12, 2008 3 :27 PM
78 En 07 Helpful Information P icture does not appear properly Ã¢ÂÂ¢ Check the setting for Color De coding when using INPUT 2 or INPUT 3 (pages 52 and 53). Ã¢ÂÂ¢ Check the setti ng for Signal Type. Ã¢ÂÂ¢ Check the setting for Video when usi ng INPUT 4 through INPUT 8 (page 54). Ã¢ÂÂ¢ Check the set ting for Signal Format when using INPUT 3 throu gh INPUT 8 (page 54). Afte r-image lag Ã¢ÂÂ¢ If a brig ht or still imag e was o n screen for a lon g period b efore sw itching to a darke r image, the original image may appear as an after-image or ghost. Try playing another bright image, switching the picture quickly many times, or show a very active scene. Ã¢ÂÂ¢ Use the Long Life Settings function (see Ã¢ÂÂ4. 2.1 Extend Your Panel LifeÃ¢ÂÂ) Ã¢ÂÂ¢ Display the Video Pattern screen to help reduce after-image lag. KURO LINK Issue Possible Solutions KURO LINK does not function Ã¢ÂÂ¢ Check the connections between th e panel and the HDMI equipment. Ã¢ÂÂ¢ Confirm that the settings for the panel are correct. Ã¢ÂÂ¢ Confirm that the equipm ent is HDMI compliant. Ã¢ÂÂ¢ Confirm that settings for the equipment are correct. F or details, refer to the operating inst ructions that came with the equipment. Error message: Ã¢ÂÂTh e device cannot be operated. Please check connectionÃ¢ÂÂ Ã¢ÂÂ¢ Check the connections between th e panel and the HDMI equipment. Ã¢ÂÂ¢ Confirm that settings for the equipment are correct. F or details, refer to the operating inst ructions that came with the equipment. No picture Ã¢ÂÂ¢ Check the connections betw een the panel and the HDMI equipment. Ã¢ÂÂ¢ Confirm that settings for the equipment are correct. F or details, refer to the operating inst ructions that came with the equipment. P anel sounds/noises Ã¢ÂÂ¢ Some sounds are appropriate for plasma technology. Examples: fan motor noise, electrical ci rcuit hummin g, glass pan el buzzin g, etc. Brightness on sides of screen are uneven Ã¢ÂÂ¢ Display content that completely fills the scree n until unevenness is minimized. Ã¢ÂÂ¢ Change the AV mo de setting. IP Control Issue Possible Solutions W eb browser screen does not open af ter entering the correct IP Address Ã¢ÂÂ¢ Confirm th at the indicator turns on after setting the LED option to On. Ã¢ÂÂ¢ Check the cable connection if the indicator does not light. Ã¢ÂÂ¢ Confirm th at the other end of the cable is properly connected to the PC , hub or router if the indic ator does no t light. The indicator lights but the web browser sc reen does not open Ã¢ÂÂ¢ Confirm that the other end of the cable is not connected to any other device than Ethernet (suc h as a telephon e). Ã¢ÂÂ¢ When using a DHCP, confirm that the I P Address allocated by the server has not changed (the address may chang e as a DHCP server r eallocates the addresses periodically). Entering an IP Address fails even after activating the DHCP function Ã¢ÂÂ¢ Confirm that the DHCP server is activated within the network. Picture Issue Possible Solutions PRO-141FD_PRO-101FD.book Page 78 M onday, May 12, 2008 3 :27 PM
79 En Helpful Information 07 If the information above fails to solve the issue, please contact a Pioneer -authorized se r vice representa tive. Do not attempt to ser vice the pa nel yourself . Opening or removing covers exposes you to possible electrical shock and other dangers as well as possibly voiding your warra nty . Request a qualified se r vice professional to che ck your flat panel display . Some situations that require a se r vice professional ar e as follows: Ã¢ÂÂ¢ panel dropped or damaged Ã¢ÂÂ¢ power cord or plug damaged Ã¢ÂÂ¢ liquid spilled or an objec t dropped into the panel Ã¢ÂÂ¢ exposed to rain or water Ã¢ÂÂ¢ noticeable abnormality in panel operation Occasionally a pa rt within the flat panel display may fail. V erif y that your ser vice professional uses only replacement parts specified by P ioneer or by those with the same characteri stics and per formance as the original parts. Use o f unautho rized parts c an result in fire, el ectric shock, or other dan ger . Upon completio n of any se r vice or repair work, request that the ser vice profess ional per form safety checks to en sure that th e product is operating properly . If you need more assi stance or ha ve a Ser vice/P arts-related qu es tion, please contact the P ioneer Ser vice organization at (800) 421-1625. No list appears on the left of the Web control system screen Ã¢ÂÂ¢ Resta rt the browse r, enter a URL in the address b ar then re-open the initial We b control system screen. IP Control Issue Possible Solution s PRO-141FD_PRO-101FD.book Page 79 M onday, May 12, 2008 3 :27 PM
80 En 08 Cautions and Warnings 8 Cautions and Warnings Y our flat panel display is designed for a long and producti ve life. T o keep your panel at peak per fo rmance, there are a few things that can he lp. This section provides general informati on and specif ic warnings to help you maintain the flat panel display at top quality throughout its lifetime. Note: If you do not intend to use your fla t panel display for an exten ded period, occasionally power o n and run the panel to maintain functionality . 8.1 Installation D etails It is best to use parts and accessories desi gned by Pio n eer . Use of accessories other th an the P ioneer stand or installation brackets may result in instabil ity and cause injur y . F or cust om installations, please speak with your dealer or expert installer before atte mpting to install your high-end flat panel display . These professionals are familiar with proper installation techniques incl uding ventilation . Using the unit without p roper ventilation may caus e the internal temperature to rise, resulting in a possible malfunction. When the surroun d ing environm ental or internal temp erature exc eeds a certa in degree , the displa y automatically powers off in ord er to cool the inte rnal electronics and prevent a hazardous situation. A malfunction ca n be caused by a single issue s uch as ve ntilation or b y a combination of factors. Pioneer is not responsible for acciden ts or damage caused by using parts and/or accessories manuf actured by other companies, inadequate inst allation sites, poor stabilization prac tices, e rroneous installation methods, operatio nal mistak es, site remodelin g, or nat ural disas ters. F or more installation information, re fer to the following bullet points: Ã¢ÂÂ¢ Confirm that pa nel vents are not part ially obstructed or completely blocked. Ã¢ÂÂ¢ Use a vacuum cleaner set to its l owest suction setting to clean dusty vents. Ã¢ÂÂ¢ Distance the panel from the wall, ot her equipment, etc. (for minimum space requirements, re fer to Ã¢ÂÂ2.2.1 Check the Location for Suitability Ã¢ÂÂ) Ã¢ÂÂ¢ Do not fit the unit in side of narrow spaces where ventilat ion is poor . Ã¢ÂÂ¢ Do not drape, seat, or enclose the panel in any materia l such as blankets, loose clot h, or carpeting as this could block the panel vents. Ã¢ÂÂ¢ Use a proper mount or stand rath er than lea ning the panel aga inst a wall or other support. Ã¢ÂÂ¢ Do not place the product on a rug or blanket. 8.2 Physical Location & Temperature Considerations Condensation may form on th e sur face or inside of the display when the panel is moved from a cold place to a warm room or just after a heater or ai r conditioner i s switched on. If condensa tion forms, do no t turn on the flat panel display until all moisture evapor ates. P owering on the display when th ere is condensation may damage the panel or ca use a malfu nction. 8.3 Usage Guidelines F or maximum enjoyment of your P ioneer flat panel di splay , read the following information carefully . Over the course of the flat panel display Ã¢ÂÂs lifetime, as with all phospho r-based scre ens including standard tube- type TVs, the l uminosity of the screen diminishes ver y slowly . Also, static pictures shown over an extended period can adversel y affect the screen i mage. T o enjoy bright and beautiful pictures for man y years to come, please apply the following guidelines. Ã¢ÂÂ¢ Set the flat panel display to St andby whe n it is not being used. Ã¢ÂÂ¢ Avoid leaving a still image or frequently showing the same picture on the screen (e.g. closed-captioned images, games with st atic portions, etc.). Ã¢ÂÂ¢ Hide the On Screen Display (OSD) from a DVD pl ayer , VCR, or other device when not in use. Ã¢ÂÂ¢ Do not leave a p icture free ze-framed o r paused for long pe riods. Ã¢ÂÂ¢ Avoid showing a picture with ver y br ight and ver y dark areas o n the sc reen for extended lengths to time. PRO-141FD_PRO-101FD.book Page 80 M onday, May 12, 2008 3 :27 PM
81 En Cautions and Warnings 08 Ã¢ÂÂ¢ Activate the GAME mode on the A V Selection submenu to pla y a game but tr y to limit using this mode for more than two hours at a time. Ã¢ÂÂ¢ View full-moti on, high-action video in WIDE or FU LL screen after playing a game or showing a still/PC image. The recommended duration for showing the action vi deo is three times a s long as the gam e or PC image was on the screen . Ã¢ÂÂ¢ View full-motion video in WIDE or FULL scree n after pl aying content with side, top, or bottom maski ng (black bars). Extensive viewing of masked content without th is recover y process can cause uneven wear on the plasma cells. 8.4 Signal Interference or Noise Signal inter ference, also referred to as video noise or white noise , can be caused by many different situ ations. The most common are addressed in the followi ng sections. Infrared rays The flat panel display releases inf rared rays because of the t echnology Ã¢ÂÂs characterist ics. Depending on how the flat pan el displa y is used, remote c ontrols fo r nearby eq uipment m ay be adv ersely af fected. Wireless headpho nes using infrared rays can experience noise interference. If this is the case, move equipment to a location where its remote control sensor is no t affecte d. Radio Signals While this flat panel display meets the required specificatio ns, it can aff ect the signals for surrounding equipment. If your radio , PC, VCR, or other electrical equipment is disrup ted by the panel, move the equipment away from the panel. Flat Panel Display Motor The screen of the flat panel display is co mposed o f extremely f ine pixels th at emit li ght accord ing to receiv ed video signals. This principle may cause you to hear a sl ight buzz or electrical hum coming from the panel. This is a normal sound f or the flat panel display a nd does not indicate a failing unit. Flat Panel Display Fans Y ou may hear the sound of a fan motor at times. The slig ht noise is caused by a c ooling fan motor s peeding up when the panelÃ¢ÂÂs ambient temp erature rises. This is a normal function of the panel and is not a malfunction. 8.5 Phosphor Prope rties The following are typic al effects and characterist ics of a phosphor-based mat rix display and as such are not covered by the W arranty: Ã¢ÂÂ¢ P ermanent residual images up on the phosphors of th e panel Ã¢ÂÂ¢ Existen ce of o ne or m ore inac tive ligh t cells in smal l quantity Ã¢ÂÂ¢ Noises generated by fan motors, electric al circuits (hum), panel plates, etc. 8.6 Image Information Including Retention & After-Image Lag Menu Window Size (aft er a Video Switch) P rograms may be broadcast in high definitio n (HD) or standard definition (SD). This flat panel display automatica lly scales to the appropriate defini tion type. If the video progra mÃ¢ÂÂs definition type changes while a menu window is on screen (for example: HD to SD or SD to HD) the menu size may temporarily shrink or enlarge until the panel fini shes adjusting the picture. Adjusting may happen , for ex ample, when switching between a TV program and playback from a DVR , or when a recorded pr ogram switches between different de finition types while the menu is showing. The menu returns to its normal size after a couple of seconds. This action is normal and does not indicate a problem with your flat panel display . Pixel Information Plasma screens show pictures using pixels. Pionee r flat pa nel di splays con tain a ver y large numb er of pixels. Th e size of the panel determines the number of pixels. Wi th the PRO-141FD/PRO -101FD, there are over 6.2 million pixels in the 50Ã¢ÂÂ/60 Ã¢ÂÂ panel . All Pioneer display p anels ar e manufactured using a ver y high level of ultra-precision technology and u ndergo individual qual ity control. PRO-141FD_PRO-101FD.book Page 81 M onday, May 12, 2008 3 :27 PM
82 En 08 Cautions and Warnings In rare cases, some pixels can be pe rman ently sw itched off , or on, resultin g in either a black or colored pixel permanently fixed on the screen . This e ffect is common to all plasma displays because i t is a consequence of the technology . 8.7 Prevent Burning After-Image La g If an imag e with ver y high peak lu minance o r fixed ima ges such as time of day indicator o r channel lo gs are displayed for more than a minute, after-im age lagging ma y occur due to the remaining electric load. Af ter-Image Lag refers to a ghost of the still image remaining visible af ter the picture is no longer being shown . This is not a malfunction. The ghost-image remaining on the screen disappears when mo ving images are shown in full screen. Image Retention (a.k.a. Burn-In) If the same image is displayed continuousl y , or for sh orter periods over several da ys, a permanent after-ima ge may remain on the screen . This after-image is perman ent because the fluorescent materials burn ed. Burned images may fade eventually after playing other video se quences but do not disappear c ompletely . Burn-in tends to occur more easily soon af ter the product is purchased. Display Samples Susceptible to Burning Ã¢ÂÂ¢ If 4:3 aspect ratio images are displayed in the ir original size repeatedly , the screen other than black or gray bars on the l ef t and right, i s susceptible to bur ning. Ã¢ÂÂ¢ If 14:9 or 16:9 letterbox images are di splayed in their original size repeatedly , the scre en other than black or gray bars at the top and bottom, is susceptible to burning. Ã¢ÂÂ¢ If fixed images such as time of da y indicator or channel logos for an extend ed period or repeatedly , the images are susceptible to burning. Ã¢ÂÂ¢ If static images, such as a fixed image from a PC or a TV game unit, are displayed for l onger periods, the images are susceptible to burning. Avoid Image Retention T o avoid image retention as much as possible, refer to the guidelines below . Ã¢ÂÂ¢ Avoid displaying images suscepti ble to burning whenever possible. Ã¢ÂÂ¢ Display content in a wide aspect ratio (no black o r gray bars on any s ide of the conten t). Use the SCREEN SIZE button on the remote control to set your flat pa n el display to a wide-viewing screen m ode (WIDE, for example). Refer to Ã¢ÂÂ5.2.1 Choose a Scre en Size (Automatically or Manually).Ã¢ÂÂ Ã¢ÂÂ¢ Select auto screen sizing (page 33) then set the Side Ma sk detection func tion to Mode 1 or Mode 2 (page 36 ). Ã¢ÂÂ¢ Set the Brightness Sync. option to Auto (adjusts the side mask brightness according to the brightness of screen images) when the screen size is 4:3 and Side Ma sk detection is set to Mode 1 or Mo de 2. Refer to Ã¢ÂÂ Lighten Side Masks Ã¢ÂÂ on page 37. Setting the Energy Sa ve function to Save 1 can further improve the ef fect (see page 29). Ã¢ÂÂ¢ Leave turning On the Image Orbiter (see page 29). Long Life Settings The Long Life Settings option simultaneously optimizes the related se ttings to guard ag ainst image retention. F or details, see Ã¢ÂÂ4.2.1 Extend Y our P anel Life.Ã¢ÂÂ Image Orbiter Another built-in fea ture to protect against burn-i n is the Orbiter functi on. Orbiter automatically changes the position of the picture imperceptibly while the image is on screen. F or more informat ion about th e feature, refer to Ã¢ÂÂ4.2.4 T urn On the Image Orbiter .Ã¢ÂÂ PRO-141FD_PRO-101FD.book Page 82 M onday, May 12, 2008 3 :27 PM
83 En Cautions and Warnings 08 8.8 Safety Precautions Y our fla t panel displ ay is engin eered and manufac tured with one of the hig hest prioriti es being safe ty . Howeve r , improper use can result in electric shock and/or fire. T o avoid danger please follow the instructions below when installi ng, ope rating, a nd clea ning your flat panel display . Ã¢ÂÂ¢ Read & R etain Instructions - R ead al l operating and user info rmation provided with your flat panel display . Ã¢ÂÂ¢ Environment - Avoid installing the pa nel in a location with exposure to la rge quantities of dust, temperature extremes, high humidit y , direct sunlight, or subj ect to excessive vibrations or impact shock. Also , never pour a liquid or insert an object in to the flat panel display . Ã¢ÂÂ¢ Cleaning - See the section above regarding the proper way to clean your flat panel display . Ã¢ÂÂ¢ W ater & Moisture - Avoid operating or positioning your panel close t o water or other sourc es of liquid. Such locations include a bathroom, a kit chen or laundr y si nk, in a damp bas ement, by a swimming pool, etc. Ã¢ÂÂ¢ P ower - T u rn OFF the panel before connec ting any other equipment . Oper ate the panel only from a grounded outlet. 8.9 Legal Notices 8.9.1 S afety WARNING This equipment is not waterproof. To prevent a fire or shock hazard, do not place any container filled with liquid near this equipment (such as a vase or fl ower pot) or expose it to dripping, splashing, rain or moisture. D3-4-2-1-3_B_En WARNING: This product equipped with a th ree-wire grounding (earthed) plug - a plug that has a third (grounding) pin. This plug only fits a grounding-ty pe power outlet. If you are unable to insert the plug into an outlet, contact a lice nsed electrician to replace the outlet wit h a properly grounded one. Do not defeat the safety purpose of the grounding plug. D3-4-2-1-6_A_En WARNING: To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the equipment. D3-4-2-1-7a_A_E n VENTILATION CAUTION: When installing this unit, make sure to lea ve space around the unit for ventilation to improve heat radiation. For the minimum space required, see page 14. WARNING: Slots and openings in t he cabinet are prov ided for ventilation to ensure reliable operation of the product, and to pro tect it from overheating. To prevent fir e hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtain s) or by operating the equipment on thick carpet or a bed. CAUTION: The power switch Ã¯ÂÂµ on this unit will not completel y shut off all power from the AC outlet. Since the power cord serves as the main disc onnect device for the unit, you w ill ne ed to unplug it from the AC outlet to shut down all power. Therefore, ma ke sure the unit has been ins talled so that the power cord can be easily unplugged from the AC outlet in case of an ac cident. To avoid fire haza rd, the power cord should also be unplugged from the AC outlet when lef t unused for a long period of ti me (for example, when on vacation). D3-4-2-2-2a_A_E n Operating E nvironment Operating en vironment tem perature and hu midity: 0 ÃÂºC to 40 ÃÂºC ( 32 ÃÂºF to 104 ÃÂºF); less than 85 %RH (cooling vents not blocked) Do not install this unit in a poorly ve ntilated area, or in loc ations exposed to high humidity or di rect sunlight (or strong artificia l light) D3-4-2-1-7c_A_E n WARNING: Do not use or store batteries in direct sunlight or other exce ssively hot place, such as inside a car or near a heater. This can cause batteries to leak, ove rheat, explode or catch fire. It can also reduce the life or performance of batteries. D3-4-2-3-3_En CAUTION: This PRO-141FD for use only with KRP-TS01 (Pio neer Corporation.) stand. Use with other stands is capable o f resultin g in inst ability causing possible injury. This PRO-101FD for use only with KRP-TS02 (Pioneer Corporation.) or KRP-SW01 (Pioneer Corporation.) stand. Use with other stands is capable of re sulting in instability causing possible injury. PRO-141FD_PRO-101FD.book Page 83 M onday, May 12, 2008 3 :27 PM
84 En 08 Cautions and Warnings 8.9.2 Radio Interference Information to User Alteratio n or modifications carried out without appropria te authorization may i nvalidate the userÃ¢ÂÂs right to operate the equipment. D8-10-2_En [For Canadian model] This Class B digital apparatus co mplies with Canadian ICES-003. D8-10-1- 3_En FEDERAL COMMUNICATIONS COMMISSION DECLARATION OF CONFORMITY This device complies with part 15 of the FCC Rules. Operatio n is subject to the follo wing two conditio ns: (1) This devic e may not cause harmful interference , and (2 ) this device must accept any interference received, including interference that may cause undesired operation. Product Name: Flat Panel Display Model Number: PRO-141FD/PRO -101FD Product Category: Cl ass B Pers onal Computers & Peripherals Responsible Party Name: PIONEE R ELECTRONICS SERVICE, INC. Address: 1925 E. DOMINGUEZ ST., LO NG BEACH, CA 90801-1760, U.S.A. Phone: 800-421-1625 URL: http://www.pioneerelectronics.com NOTE: This equipment has been tested and found to comply with the limits for a Cl ass B digital device, pursuant to Part 15 of the FCC Ru les. These limits are designed to pr ovide reasonable protection against harmful interference in a residentia l installation . This equipment generates, uses, and ca n radiate radio frequenc y energy an d, if not inst alled and used in acc ordance w ith the inst ructions, may cause harmful interference to radio communications. However, there is no guarantee th at interference wi ll not occur in a particular installation. If this equipment does cause harmful interference to radi o or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Ã¢ÂÂ Reorient or re locate the rece iving antenn a. Ã¢ÂÂ Increase the separation between the equipment and receiver. Ã¢ÂÂ Connect the equipment into an outlet on a circuit di fferent from tha t to which the receiver is connected. Ã¢ÂÂ Consult the dealer or an experienced radio/T V technician for help. D8-10-1- 2_En CAUTION: This product satisfies FCC regulati ons when shie lded cables and connecto rs are used to connect the unit to other equipment. To prev ent electromagnetic interference with electri c appliances such as radios and televisions, use shielded cables and connectors for connections. D8-10-3a _En PRO-141FD_PRO-101FD.book Page 84 M onday, May 12, 2008 3 :27 PM
85 En 09 Appendix 9 Appendix 9.1 Manufacturer Codes to Program into the Remote Control 9.1.1 Cable Brand/Code Brand/Code Brand/Code Brand/Code Brand/Code Brand/Code A-Mark 0008, 0144, 0277 ABC 0003, 0008, 0237 Accuphase 0003 Acorn 0237 Action 0237 Active 0237 ADB 1927 Americast 0899 Amstrad 1222 Archer 0237 Auna 0277 Austar 0012, 0276 BCC 0276 Bell South 0899 Birmingham Cable Communications 0276 British T elecom 0003 Cable & Wir el e s s 1068 Centur y 0008 Daer yung 0008, 0277, 0477, 0877, 1877 Digeo 1187 Director 0476 DX Antenna 1500 Encon 0008 Fo s g a t e 0276 Fo x t e l 1222 F rance T elecom 0817 Fr e e b o x 1482 Fu j i t s u 1497 Galaxi 0008 GE 0144, 0237 Gehua 0476 General Instrument 0003, 0012, 0276, 0476, 0810 Gibralter 0003 GoldStar 0144 Hitachi 0003, 0008 Humax 1981 Insight 0476, 0810 Jerrold 0003, 0012, 0276, 0476, 0810 Kabel Deutschland 1981 Kabelvision 0003 Kloss 0277 KNC 0008 LG 0144 Macab 0817 Melita 0003 Memorex 0000 Mitsubishi 0003 Motorola 0276, 0476, 0810, 1187, 1376 MultiVision 0012 NEC 1496 NET 0012, 0277 Noos 0817 Nova Vision 0008, 0277 Novaplex 0008, 0277 NSC 0012 NTL 0003, 0276, 0277, 1060, 1068 Ono 1068 Optus 0276, 1060 Pa c e 0008, 0237, 0877, 1060, 1068, 1577, 1877 Pa n a m a 0107 P anasonic 0000, 0008, 0107, 0144, 1488 Pa r a g o n 0000, 0008, 0525 P enney 0000 Philips 0317, 0817, 1305 Pioneer 0144, 0533, 0877, 1021, 1500, 1877 Pr i s m 0012 Pu l s a r 0000 PVP Stereo Visual Matrix 0003 Quasar 0000 Reg a l 0276 Runco 0000 Sagem 0817 Salora 0000 Samsung 0000, 0003, 0144, 1060, 1666 Scientific Atlanta 0000, 0003, 0008, 0012, 0237, 0277, 0477, 0877, 1877 Sony 1006, 1460 Sprucer 0144 Starcom 0003 StarHub 0276, 1927 Sumitomo 1500 Supercable 0276 Te l e w e s t 1068 Thomson 1981 Time W arner 1877 To c o m 0012 To r x 0003 To s h i b a 0000, 1509 Tr a n s P X 0276 TS 0003 United Cable 0003, 0276 US Electronics 0003, 0008, 0276, 0277 Vid eo w ay 0000 Vis i op as s 0817 Zenith 0000, 0008, 0525, 0899 PRO-141FD_PRO-101FD.book Page 85 M onday, May 12, 2008 3 :27 PM
86 En 09 Appendix 9.1.2 Satellite Brand/Code Brand/Code Brand/Code Brand/Code Brand/Code Brand/Code @sat 1300 @Sky 1334 ADB 0642, 0887, 1367 Akai 0200 Alba 1284 Allsat 0200 Allvision 1232, 1334, 1412 AlphaStar 0772 Amstrad 0847, 1113, 1175 Aonvision 2279 Apro 1672 Armstrong 0200 Arnion 1300 Asat 0200 ASCI 1334 AssCom 0853 Astro 0173, 1100, 1113 Atsat 1300 AtSky 1334 Audioline 1672 Aurora 0642, 0879, 1433 Austar 0642, 0879, 1176 Axil 1457 Axis 1111 B@ytronic 1412 Bell Express V u 0775 Big Sat 1457 Black Diamond 1284 Blaupunkt 0173 Boca 1232 Boston 1251 Brainwave 1672 British Sky Broadcasting 0847, 1175 BskyB 0847, 1175 Bush 1284, 1645, 1672 Canal 0853 Canal Digital 0853 Canal Satellite 0853 Canal 0853 Centrex 1457 Centur y 0856 CGV 1413, 1567 Chaparral 0216 Chess 1334, 1626 CityCom 1176, 1232 Classic 1672 Clatronic 1413 CNS 1367 Comag 1232, 1412, 1413 Coship 1457 Crown 1284 Cyfra 1076 Cyrus 0200 D-b ox 0723, 1114 Daewoo 1111 Digifusion 1645 Digihome 1284 DigiLogic 1284 DigiQuest 1300, 1457 DigiSat 1232 Digisky 1457 Digiturk 1076 DiP ro 1367 DirecTV 0099, 0247, 0392, 0566, 0639, 0749, 0819, 1076, 1108, 1142, 1377, 1392, 1414, 1442, 1609, 1639, 1749, 1856 Dish Network System 0775, 1505, 1775 Dishpro 0775, 1505, 1775 DNT 0200 Draco 1375 Dream Multimedia 1237 DSE 1375 DSTV 0642, 0879, 1433 Durabrand 1284 Echostar 0775, 0853, 1323, 1409, 1505, 1775 Elap 1567 Elta 0200 Engel 1251 Esat 0879 EuroLine 1251 Expressvu 0775, 1775 F erguson 1291 FMD 1251, 1413, 1457 Fo x t e l 0879, 1176 Fu b a 0173, 1214, 1251 F unai 1377 Galaxis 0853, 0879, 1111 GbSA T 1214 GE 0392, 0566 Gecco 1412 General Instrument 0869 General Satellite 1176 Globo 1251, 1334, 1412, 1429, 1626 GOD Digital 0200 GOI 0775, 1775 Gold Box 0853 GoldMaster 1334 Goodmans 1284, 1291 Gradiente 0099, 0856, 0887 Grandin 1626 Grundig 0173, 0847, 0853, 0879, 1284, 1291 Hanseatic 1100 Hauppauge 1672 HB 1214 Hills 1232, 2209 Hirschmann 0173, 1111, 1232, 1412 Hitachi 0749, 0819, 1250, 1284 Homecast 1214 Hornet 1300 Houston 0775 HTS 0775, 1775 Hughes Network Systems 0749, 1142, 1442, 1749 Humax 1176, 1427, 1675, 1808 iCan 1367 ID Digital 1176 Imperial 1334, 1429, 1672 Indovision 0856, 0887 Innova 0099 Interstar 1214 ISkyB 0887 IT T Nokia 0723 Jadeworld 0642 Jaeger 1334 Jerrold 0869 JVC 0492, 0775, 1775 Kaon 1300 KaT elco 1111 Kathrein 0173, 0200, 1416, 1561, 1567 Kenwood 0853 Kreiling 1626 Kreiselmeyer 0173 L&S Electronic 1334 LaSA T 0173 Lemon 1334 Lenoxx 1611 LG 1414 Listo 1626 Lodos 1284 Logik 1284 Magnavox 0722 Marantz 0200 Maspro 0173 Matsui 0173, 1284 Maximum 1334 McIntosh 0869 Mediabox 0853 Mediacom 1206 MediaSat 0853 Medion 1232, 1334, 1412, 1626 Mega 0200 Metronic 1334, 1375 Metz 0173 Mitsubishi 0749 MorganÃ¢ÂÂs 0200, 1232, 1412 PRO-141FD_PRO-101FD.book Page 86 M onday, May 12, 2008 3 :27 PM
87 En 09 Appendix Brand/Code Brand/Code Brand/Code Brand/Code Brand/Code Brand/Code Motorola 0856, 0869 MTEC 1214 Multibroadcast 0642, 0879 Multichoice 0642, 0879, 1433 Myr yad 0200 NEOTION 1334 Netsat 0099, 0887 Neuling 1232 Next Level 0869 Nikko 0200, 0723 Nokia 0723, 0853, 1023, 1223 Nordmende 1611 OctalTV 1505 Omega 0887 Opentel 1232, 1412 Optex 1611, 1626 Optus 0879 Orbis 1232, 1334, 1412 Orbitech 1100 P/Sat 1232 Pa c e 0200, 0329, 0847, 0853, 0887, 1175, 1323, 1423 Pa c i f i c 1284, 1375 Pa c k a r d B e l l 1111 Pa l c o m 1409 Pa n a s a t 0879, 1433 P anasonic 0247, 0701, 0847, 1304, 1404 Pa n d a 0173 peeKT on 1457 Philips 0099, 0173, 0200, 0722, 0749, 0775, 0819, 0847, 0853, 0856, 0887, 1076, 1114, 1142, 1442, 1672, 1749 Pi n o 1334 Pioneer 0329, 0853, 1308 PMB 1611 P reisner 1113 Pr e m i er 0723, 0853, 1429 Pr i m a c o m 1111 Pr i m e s t a r 0869 P roscan 0392, 0566 QNS 1367, 1404 Rad i ol a 0200 Rad i oS h a ck 0566, 0775, 0869 Rad i x 1113 RCA 0143, 0392, 0566, 0775, 0855, 1142, 1291, 1392, 1442 Reb o x 1214 Reg a l 1251 RF T 0200 Roadstar 0853 Roll master 1413 Rown s on ic 1567 SAB 1251 Saba 0820 Sagem 0820, 1114 Samsung 0853, 1108, 1142, 1206, 1276, 1377, 1442, 1458, 1570, 1609 Sanyo 1219 Sat Control 1300 SA T 1409 Satelco 1232 Satplus 1100 Schaub Lorenz 1214 Schneider 1206, 1251 Schwaiger 1111, 1334, 1412, 1457 Sedea Electronique 1206, 1626 SEG 1251, 1626 Septimo 1375 Serd 1412 Ser vimat 1611 Ser viSat 1251 Siemens 0173, 1334, 1429 SKY 0099, 0847, 0856, 0887, 1175, 1856 Sky Brazil 0856, 0887 SKY Italia 0853 Sky XL 1251, 1412 Sky 1175 Skymaster 1334, 1409, 1567, 1611 Skymax 0200 Skyplus 1232, 1334, 1412 Skyvision 1334 SL 1672 SM Electronic 1409 Smart 1113, 1232, 1404, 1413 Sony 0639, 0847, 0853, 1558, 1639 Star 0887 Star Choice 0869 Star T rak 0772, 0869 Starlite 0200 Strong 0820, 0853, 0879, 1284, 1300, 1409, 1626 Sunny 1300 Sunstar 0642 Supernova 0887 Supratech 1413 Systec 1334 Te a c 1251 T echniSat 1100, 1195 T echnosat 1206 T echnosonic 1672 T echnotrend 1429 Te c h w o o d 1284, 1626 TELE System 1251, 1409, 1611 Te l e C l u b 1367 Te l e s t a r 1100, 1251, 1334, 1626, 1672 Te l e v e s 1214, 1300, 1334 Te l e v i s a 0887 Te l e w i r e 1232 Te v i o n 1409, 1672 Thomson 0392, 0566, 0820, 0847, 0853, 1046, 1175, 1291 Tin y 1672 Tiv id i 1429 Tiv o 1142, 1442 To k a i 0200 T onna 1611 To p f i e l d 1206, 1208 To s h i b a 0749, 0790, 1284, 1749 TPS 0820 Tr i a x 0200, 0853, 1113, 1251, 1291, 1611, 1626 TT - m i c r o 1429 T winner 1611 UEC 0879 UltimateTV 1392 Uniden 0722 Unisat 0200 United 1251 Universum 0173, 1251 Va r i o s a t 0173 Ve n t a n a 0200 Ve s t e l 1251 Vic t or 0492 Vie w Sa t 1232 Vis i os at 1413, 1457 Viv a 0856 V oom 0869 Wa v e l e n g t h 1232, 1413 Whar fedale 1284 Wis i 0173, 1232 Wo r l d s a t 1214, 1251 Xsat 0847, 1214, 1323 Xtreme 1300 Ya k u m o 1413 Ye s 0887 Zehnder 1232, 1251, 1334, 1412, 1413 Zenith 0856, 1856 Zeta T echnology 0200 Zinwell 2280 PRO-141FD_PRO-101FD.book Page 87 M onday, May 12, 2008 3 :27 PM
88 En 09 Appendix 9.1.3 VCR Brand/Code Brand/Code Brand/Code Brand/Code Brand/Code Brand/Code A-Mark 0000, 0037, 0278 ABS 1972 Accurian 0000 Admiral 0039, 0047, 0048, 0060, 0121, 0209 Adventura 0000, 0037 Aiko 0278 Aim 0278, 0348, 0642 Aiwa 0000, 0032, 0037, 0209, 0348, 1291 Akai 0037, 0315, 0348, 0642 Alba 0000, 0081, 0209, 0278, 0315, 0348 Alienware 1972 Allegro 0039 Allstar 0081 America Action 0278 American High 0035, 0081 Amstrad 0000, 0278 Anam 0037, 0162, 0226, 0278 Anam Nationa l 0162, 0226, 1162, 1562 Ansonic 0000 Aristona 0081 ASA 0037, 0081 Astra 0035 Asuka 0000, 0037, 0038, 0081 Audio- T echnica 0058 Audiolab 0081 Audiosonic 0278 Audiovox 0037, 0038, 0278 Avis 0000 AV P 0000 Awa 0037, 0043, 0278, 0642 Baird 0000, 0278 Basic Line 0278 Bell & Howell 0000, 0035, 0039, 0048 Bestar 0278 Black Diamond 0642 Black P anther 0278 Blaupunkt 0081, 0162, 0226 Blue Sky 0037, 0209, 0278, 0348, 0642 Brandt 0320 Brinkmann 0209, 0348 Broksonic 0121, 0184, 0209, 0348 Bush 0000, 0081, 0209, 0278, 0315, 0348, 0642 Calix 0037 Candle 0037, 0038 Canon 0035 Carena 0081, 0209 Carrefour 0045 Car ver 0035, 0081 Casio 0000 Cathay 0278 CCE 0278 CGE 0000 Changhon g 0048, 0081 Cimline 0209 Cineral 0278 Citizen 0000, 0035, 0037, 0209, 0278 Classi c 0037 Clatronic 0000 Colorty me 0035, 0045, 0060, 0278 Colt 0000 Condor 0278 Craig 0037, 0047 PRO-141FD_PRO-101FD.book Page 88 M onday, May 12, 2008 3 :27 PM
89 En 09 Appendix Brand/Code Brand/Code Brand/Code Brand/Code Brand/Code Brand/Code Criterion 0000 Crosley 0000, 0035, 0081, 0149 Crown 0037, 0278 Curtis Mathes 0000, 0035, 0060, 0162, 0278 CyberP o wer 1972 Cyrus 0081 Daewoo 0037, 0045, 0209, 0278, 0642 Dansai 0278 Daytron 0037, 0278 De Graaf 0042, 0048, 0081 Decca 0000, 0067, 0081, 0209 Degraff 0042, 0048, 0081 Deitron 0278 Dell 1972 Denon 0042, 0081 Diamant 0037 Diamond 0348 Dick Smith Electronics 0642 Digitor 0642 DirecTV 0739 Domland 0209 DSE 0642 Dual 0000, 0081, 0278, 0348 Dumont 0000, 0081 Durabrand 0038, 0039, 0642 Dynatech 0000 Elbe 0038, 0278 Electrohome 0000, 0037, 0043, 0060, 0209 Electrophonic 0037 Elta 0278 Emerald 0121, 0184 Emerex 0032 Emerson 0000, 0035, 0037, 0039, 0043, 0045, 0121, 0184, 0209, 0278, 0348 ESC 0278 F erguson 0000, 0278, 0320, 0348 Fid e l it y 0000 Fin l a nd i a 0000, 0037, 0042, 0043, 0048, 0081, 0226 Finlux 0000, 0042, 0081 Fir s t li n e 0037, 0042, 0043, 0045, 0209, 0278, 0348 Fis h e r 0000, 0039, 0047 Flint 0209, 0348 Fu j i 0033, 0035 Fu j i t s u 0000, 0037, 0045 F ujitsu General 0037 F unai 0000, 0037, 0278 Galaxi 0000 Galaxis 0278 Garrard 0000 Gateway 1972 GE 0000, 0035, 0048, 0060, 0149, 0226, 0320 GEC 0081 Gemini 0060 General 0045 General T echnic 0348 Genexxa 0000, 0037, 0278 Go Video 0614 GoldStar 0000, 0035, 0037, 0038, 0039, 0209, 0225, 0226, 0278 Goodmans 0000, 0037, 0081, 0209, 0278, 0348, 0642 GPX 0037 Gradiente 0000 Granada 0000, 0035, 0037, 0042, 0048, 0081, 0226 Grandin 0000, 0037, 0209, 0278 Grundig 0081, 0226, 0320, 0348 Haaz 0348 Hanseatic 0037, 0038, 0081, 0209 Harley Davidson 0000 Harman/Kardon 0038, 0081 Hewlett P ackard 1972 HI-Q 0000, 0035, 0047 Hinari 0209, 0278 Hisawa 0209 Hischito 0045 Hitachi 0000, 0035, 0037, 0042, 0045, 0081, 0089 Hoeher 0278, 0642 Hornyphon 0081 Howard Computers 1972 HP 1972 Hughes Network Systems 0042, 0739 Humax 0739 Hush 1972 Hypson 0000, 0037, 0209, 0278 Hytek 0000, 0047 iBUYPOWER 1972 Imperial 0000 Ingersol 0209 Instant Replay 0035, 0226 Interbuy 0037 Inter funk 0081 Internal 0278 International 0037, 0278, 0642 Inter vision 0000, 0037, 0209, 0278, 0348 Irradio 0037, 0081 ITV 0037, 0278 JBL 0278 Jensen 0067 JMB 0209, 0348 Joyce 0000 JVC 0045, 0058, 0067, 0081, 0184, 1162, 1279 Kambrook 0037 Karcher 0081, 0278, 0642 KEC 0037, 0278 Kendo 0037, 0209, 0278, 0315, 0348, 0642 Kenwood 0038, 0067 KIC 0000 Kimari 0047 Kioto 0348 Kneissel 0037, 0209, 0278, 0348 Kod ak 0035, 0037 Kol in 0043 Kol st er 0209 KTV 0000 Kub a 0047 Kub a E le c tr on ic 0047 Lenco 0278 LG 0000, 0037, 0038, 0042, 0045, 0209, 0225, 0278 Lifetec 0209, 0348 Linksys 1972 LloydÃ¢ÂÂs 0000, 0038 Loewe 0037, 0081, 0162, 1062, 1562 Logik 0000, 0209 Lumatron 0278 Luxor 0043, 0047, 0048, 0315 LXI 0000, 0037, 0042, 0067 M Electronic 0000, 0037, 0038 Magnadyne 0081 Magnasonic 0000, 0037, 0278 Magnavox 0000, 0035, 0037, 0039, 0048, 0081, 0149, 0226, 0642 Magnum 0642 Manesth 0045, 0081, 0209 Marantz 0035, 0038, 0081, 0209 Mark 0000, 0278 Marta 0037 Mastec 0642 Master Ã¢ÂÂs 0278 PRO-141FD_PRO-101FD.book Page 89 M onday, May 12, 2008 3 :27 PM
90 En 09 Appendix Brand/Code Brand/Code Brand/Code Brand/Code Brand/Code Brand/Code Matsui 0037, 0209, 0278, 0348 Matsushita 0035, 0081, 0162, 0226, 1162 Media Center PC 1972 Mediator 0081 Medion 0209, 0348, 0642 MEI 0035 Memorex 0000, 0035, 0037, 0039, 0047, 0048, 0162, 0209, 0278, 0348, 1162 Metronic 0081 Metz 0037, 0081, 0162, 0226, 1062, 1162, 1562 MGA 0043, 0060 Micormay 0348 Micromaxx 0209 Microso ft 1972 Migros 0000 Mind 1972 Minolta 0042 Mitsubishi 0000, 0042, 0043, 0047, 0048, 0060, 0067, 0081, 0642 Motorola 0035, 0048 MTC 0000 MTX 0000 Multitec 0037 Multitech 0000, 0039 Murphy 0000 Myr yad 0081 NAD 0058 Naik o 0348, 0642 NAP 0039 National 0226 Nebula Electronics 0033 NEC 0035, 0037, 0038, 0048, 0067, 0278 Neckermann 0081 Nesco 0000 Neufunk 0209 Newave 0037 Nikkai 0278 Nikko 0037, 0278 Nikkodo 0037, 0278 Niveus Media 1972 Nokia 0042, 0048, 0081, 0278, 0315 Nordmende 0067, 0320 Northgate 1972 Nu- T ec 0209 Oceanic 0000, 0048, 0081 Okano 0209, 0278, 0315, 0348 Olympus 0035, 0162, 0226 Onimax 0642 Onkyo 0222 Optimus 0000, 0035, 0037, 0047, 0048, 0058, 0162, 1062, 1162 Orion 0000, 0121, 0184, 0209, 0278, 0348 Orson 0000 Osaki 0000, 0037 Otake 0209 Otto V ersand 0081 Pa c i f i c 0000, 0348, 0642 Pa c k a r d B e l l 1972 Pa l l a d i u m 0037, 0209, 0348 P alsonic 0000, 0642 Pa n a m a 0035 P anasonic 0000, 0035, 0162, 0225, 0226, 0614, 0616, 1062, 1162, 1244, 1293, 1562 Pa t h e C i n e m a 0043 P enney 0000, 0035, 0037, 0038, 0042, 0047, 0067, 0081, 0162 Pe n t a x 0042 Pe r d i o 0000, 0209 Philco 0000, 0035, 0038, 0081, 0209, 0226 Philips 0000, 0035, 0045, 0048, 0081, 0162, 0209, 0226, 0616, 0739 Phoenix 0278 Phonola 0081 Pi l o t 0037 Pioneer 0042, 0058, 0067, 0081, 0162, 0168 Po l k A u d i o 0081 P ortland 0278 P recision 0058 Pr i n z 0000 P rofitronic 0081 Pr o l i n e 0000, 0278, 0320, 0642 P roscan 0060 P rosco 0278 Pr o s o n i c 0209, 0278 Pr o t e c 0000 Pr o t e c h 0081 P roVis ion 0278 Pu l s a r 0039, 0278 Pye 0000, 0081 Qisheng 0060 Quartz 0035, 0047 Quasar 0035, 0162, 0226, 0278, 1162 Quelle 0081 Rad i al v a 0037, 0048, 0081 Rad io la 0081 Radionette 0037 Rad io Sha c k 0000, 0035, 0037, 0047, 0048, 0162, 1162 Rad ix 0037 Rand e x 0037 RCA 0000, 0035, 0042, 0045, 0048, 0058, 0060, 0149, 0226, 0320, 0880 Realistic 0000, 0035, 0037, 0047, 0048, 0121, 0162, 0278, 1162 Reo c 0348 Rep la yT V 0614, 0616 Ricavision 1972 Roadstar 0037, 0038, 0081, 0278 Runco 0039 Saba 0278, 0320 Saisho 0209, 0348 Salora 0043 Sampo 0037, 0048 Samsung 0000, 0038, 0045, 0060, 0739 Sanky 0039, 0048 Sansei 0048 Sansui 0000, 0067, 0209, 0348 Sanyo 0000, 0047, 0048, 0067, 0348 Saville 0278 SBR 0081 Schaub Lorenz 0000, 0315, 0348 Schneider 0000, 0037, 0042, 0081, 0278, 0348, 0642 Scott 0043, 0045, 0121, 0184 Sears 0000, 0033, 0035, 0037, 0039, 0042, 0043, 0045, 0047, 0048, 0058, 0060, 0067, 0162, 0209 Seaway 0278 SEG 0081, 0278, 0642 SEI 0081 Sei-Sinudyne 0081 Seleco 0037 Semivox 0045, 0209 Semp 0045 Sentra 0278 Sharp 0000, 0032, 0037, 0047, 0048, 0209, 1285 Shinco 0000 Shintom 0000, 0039 Shivaki 0037 Siemens 0037, 0081, 0320 PRO-141FD_PRO-101FD.book Page 90 M onday, May 12, 2008 3 :27 PM
91 En 09 Appendix 9.1.4 B DP (B lu-ray ) Brand/Code Brand/Code Brand/Code Brand/Code Brand/Code Brand/Code Siera 0081 Signature 0000, 0035, 0037, 0048, 0060, 0149 Silva 0037 Silver 0278 SilverCrest 0642 Singer 0037, 0045, 0348 Sinudyne 0081, 0209 Smaragd 0348 Sonic Blue 0614, 0616 Sonolor 0048 Sontec 0037, 0278 Sonwa 0642 Sony 0000, 0032, 0033, 0035, 0047, 0048, 0067, 0226, 1636, 1972 Soundmaster 0000 Soundwave 0037, 0209, 0348 Stack 9 1972 Standard 0278 Stern 0278 STS 0042 Sunkai 0209, 0278, 0348 Sunstar 0000 Suntronic 0000 Supra 0037, 0278, 0348 Susumu 0037 SV2000 0000 SV A 0000 Sylvania 0000, 0035, 0043, 0081 Symphonic 0000 Systemax 1972 T A 0162 Ta g a r S y s t e m s 1972 Ta i s h o 0209 T andbe rg 0278 Ta n d y 0000 Ta s h i k o 0000, 0037, 0048, 0081 T atung 0000, 0043, 0045, 0048, 0067, 0081, 0209, 0348 Tc h i b o 0348 TCM 0348 Te a c 0000, 0037, 0067, 0278, 0642 T echnics 0000, 0035, 0037, 0081, 0162, 0226, 1162 T e chniSat 0348 Te c o 0035, 0037, 0038, 0048 Te d e l e x 0037, 0209, 0348, 0642 Te k n i k a 0000, 0035, 0037 T e lefunken 0209, 0278, 0320, 0642 T e lerent 0226 Te l e s t a r 0037 Te l e t e c h 0000, 0278 Te n s a i 0000, 0037, 0278 Te v i o n 0209, 0348, 0642 T exet 0278 Thomas 0000 Thomson 0060, 0067, 0278, 0320 Thorn 0037, 0320 Tis o n i c 0278 Tiv o 0739, 1996 TMK 0000 TNIX 0037 To k a i 0037 T opline 0348 To s h i b a 0000, 0042, 0043, 0045, 0067, 0081, 0209, 1008, 1290, 1972, 1996 To s o n i c 0278 To t e v i s i o n 0037 To u c h 1972 To y o d a 0278 Tr a d e x 0081 Tr i a d 0278 Tr i x 0037 Ultra 0045, 0278 Ultravox 0278 United 0348 Universum 0000, 0037, 0081, 0209, 0348 Ve c t o r 0045 V ector Research 0038, 0184 Vic to r 0067 Vid eo Co n ce p ts 0045 Video T echnic 0000 Vid eo m ag ic 0037 Videosonic 0000 Vie ws o ni c 1972 Vil la i n 0000 V oodoo 1972 Wa r d s 0000, 0033, 0035, 0037, 0038, 0039, 0042, 0043, 0045, 0047, 0048, 0058, 0060, 0081, 0149 Wa t s o n 0081, 0642 W eltblick 0037 Whar fedale 0642 White We s t i n g h o u s e 0000, 0209, 0278 Wo r l d 0209, 0348 XR -1000 0000, 0035 Ya m a h a 0038 Ya m i s h i 0278 Yo k o 0037 Zenith 0000, 0033, 0037, 0039, 0209, 0278 ZT Group 1972 ZX 0209, 0348 Brand/Code Brand/Code Brand/Code Brand/Code Brand/Code Brand/Code LG 0741 Microso ft 2083 Onkyo 1769 P anasonic 1641 Philips 2084 Pioneer 0142, 2052 RCA 1769 Samsung 0199 Sony 1516 To s h i b a 1769 Xbox 2083 PRO-141FD_PRO-101FD.book Page 91 M onday, May 12, 2008 3 :27 PM
92 En 09 Appendix 9.1.5 DVD-R Brand/Code Brand/Code Brand/Code Brand/Code Brand/Code Brand/Code Accurian 0675 Apex Digital 1056 Aristona 0646 Cat 1421 Centrum 1227 CyberHome 1129 Denon 0490 Denver 1056 Digitrex 1056 Ellion 1421 Emerson 0675 F unai 0675 Go Video 0741 GPX 0741 H & B 1421 Hitachi 1664 Humax 0646 JVC 1164 Kreisen 1421 LG 0741 Loewe 0741 Magnavox 0646, 0675 Mitsubishi 1403 P alsonic 1056 P anasonic 0490 Philips 0646, 1340 Pioneer 0571, 0631, 1475, 1476, 2216 Pye 0646 RCA 0522 Roa d s ta r 1227 Samsung 0490 Schneider 0646 Sharp 0630, 0675 Sony 1033, 1070, 1431 Star Clusters 1227 Sylvania 0675 Ta r g a 1227 Te a c 1227 Te v i o n 1227 Thomson 0551 Universum 1227 Ya k u m o 1056 Ya m a d a 1056 Ya m a h a 0646 Zenith 0741 PRO-141FD_PRO-101FD.book Page 92 M onday, May 12, 2008 3 :27 PM
93 En 09 Appendix 9.1.6 DVD Brand/Code Brand/Code Brand/Code Brand/Code Brand/Code Brand/Code 3D LAB 0503, 0539 A- T rend 0714 Accurian 0675 Acoustic Solutions 0713, 1228 AEG 0788, 1233 AFK 1152 Aim 0672 Airis 0672, 1224 Aiwa 0533, 0641 Akai 0690, 0695, 0788, 0898, 1115, 1233 Akura 0898, 1233 Alba 0539, 0672, 0695, 0713 Allegro 0869 Altacom 1224 Amitech 0850 Amstrad 0713 Ansonic 0759 Apex Digital 0533, 0672, 1056, 1061 Arena 1115 Aristona 0539, 0646 Arrgo 1023 Asono 1224 Atacom 1224 Audiosonic 0690 Audix 0713 Autovox 0713 Auvio 0843 Basic Line 0713 Baze 0898 BBK 1224 Bel Canto Design 1571 Black Diamond 0713 Blu:sens 1233 Blue P arade 0571 Blue Sky 0672, 0695, 0713, 0843 Boman 0898 Brainwav e 1115 Brandt 0503, 0551 Broksonic 0695 Bush 0672, 0690, 0713, 0723 C- T e c h 1152 California Audio Labs 0490 Cambridge Soundworks 0690 Cat 0789, 1421 Centrex 0672 Centrum 0713, 0789, 1227 CGV 1115 Changhong 0627, 1061 Cinea 0841 Cinetec 0713 CineVision 0869 Citizen 0695 Clairtone 0571 Clatronic 0672, 0675, 0788, 1233 Clayton 0713 Codex 1233 Conia 0672 Contel 0788 Creative 0503, 0539 Crown 0690, 0713, 1115 Cr ypto 1228 CyberHome 0714, 0816, 1023, 1129 D- Vi si on 1115 Daewoo 0490, 0714, 0869, 1172 Dansai 1115 Dantax 0539, 0713, 0723 Decca 1115 Denon 0490, 0634, 1282, 1406 Denver 0672, 0788, 0898, 1056 Desay 0843 Dgtec 0672 Dick Smith Electronics 1152 Digihome 0713 DigiLogic 0713 Digitor 0690 Digitrex 0672, 1056 Dinamic 0788 Disney 0675, 1270 DSE 1152 Dual 0675, 0713, 1023 Durabrand 0713, 1023 DVD2000 0521 E:max 1233 EagleT ec 0714 eBench 1152 Eclipse 0723 Elfunk 0713, 0850 Elite 1152 Ellion 0850, 1421 Elta 0672, 0690, 0788, 0850, 1115, 1233 Eltax 1233 Emerson 0591, 0675, 0821 Enterprise 0591 Entivo 0503, 0539 Enzer 1228 ESA 0821 EuroLine 0675, 0788, 1115, 1233 F erguson 0695, 0713, 0898 Finlux 0591, 0672, 0741 Fir s t li n e 0713, 0843, 0869 F unai 0675, 0695 GE 0522, 0815 Global Link 1224 Global Sphere 1152 Go Video 0573, 0741, 0744, 0869, 1044, 1075 GoldStar 0591, 0741, 0869 Goodmans 0690, 0713, 0723 GPX 0741 Gradiente 0490 Gran P rix 0898 Grandin 0713, 1233 Grundig 0539, 0551, 0695, 0713 H & B 0713, 0841, 0850, 1233, 1421 Haaz 1152 Haier 0843 Hanseatic 0741 Harman/Kardon 0582, 0702 HCM 0788 Henss 0713 HiMAX 0843 Hitachi 0573, 0664, 0695, 0713, 1664 Hiteker 0672 Hoeher 0713, 1224 Home T e ch Industries 1224 HotMedia 1152 Humax 0646 Hyundai 0850, 1061, 1228 Ingelen 0788 Ingersol 1023 Inno Hit 0713 Integra 0571, 0612, 0627 Irradio 0869, 1115, 1224, 1233 ISP 0695 JBL 0702 JMB 0695 JNC 0672 JVC 0503, 0539, 0558, 0623, 0867, 1164 Kansas T e chnologies 1233 Kendo 0672, 0713 Kennex 0713, 0898 Kenwood 0490, 0534 Kiss 0841 KLH 0815 Kloss 0533 Kos s 1061 Kreisen 1421 Lasonic 0627, 0789 Lecson 1533 Lenco 0713 Lenoir 1228 Lenoxx 0690 PRO-141FD_PRO-101FD.book Page 93 M onday, May 12, 2008 3 :27 PM
94 En 09 Appendix Brand/Code Brand/Code Brand/Code Brand/Code Brand/Code Brand/Code LG 0591, 0741, 0869 LiteOn 1058 Lodos 0713 Loewe 0511, 0539, 0741 Logik 0713 Lumatron 0695, 0713, 0741, 1115 Lunatron 0741 Luxman 0573 Luxor 0713 Magnasonic 0675 Magnavox 0503, 0539, 0646, 0675, 0713, 0821, 1354 Magnex 0723 Manhattan 0713 Marantz 0503, 0539, 0675 Mark 0713 Matsui 0672, 0695, 0713 Maxdor f 0788 Maxim 0713 MBO 0690 McIntosh 1533 MDS 0713 Medion 0630, 1270 Memorex 0695, 1270 Metronic 0690 Metz 0525, 0571, 0713 MiCO 0723 Micromaxx 0695 Micromedia 0503, 0539 Micromega 0539 Microsoft 0522, 2083 Minato 0752 Minax 0713 Minoka 1115 Mirror 0752 Mitsubishi 0521, 0713, 1403, 1521 MPX 0843 NAD 0741 NEC 0741, 0785, 0869 Norik o 0752 Nowa 0843 Nu- T ec 1228 Okano 0752 Olidata 0672 Omni 0690 Onkyo 0503, 0612, 0627, 1769 Oppo 1224 Optim 0843 Optimus 0525, 0571 Orion 0695, 1233 Ormond 0713 Pa c i f i c 0695, 0713, 0759 P a lladium 0695, 0713 P alsonic 0672, 1056 P anasonic 0490, 0503, 0571, 0703, 1282, 1362, 1462, 1641, 1762 Pa n d a 0789 peeKT on 0898, 1224 Philco 0675, 0690, 0788 Philips 0503, 0539, 0585, 0646, 0675, 1340, 1354, 2056, 2084 Pioneer 0142, 0490, 0525, 0571, 0631, 1475, 1476, 1571, 2052, 2216 Plu2 0850 P olaroid 1061 Po l k A u d i o 0539 P residian 0675 Pr i m a 1228 P roceed 0672 Pr o l i n e 0672 P roscan 0522 P roson 0713 P rosonic 0752 Pye 0539, 0646 Radionette 0741, 0869 Rad i oS h a ck 0571 RCA 0522, 0571, 0822, 1132, 1769 Rea l i st i c 0571 REC 0490 Red s t ar 0759, 0788, 0898 Reo c 0752 Rev o y 0841 Richmond 1233 Rio 0869 Roa d s ta r 0672, 0690, 0713, 0898, 1227 Roc k so n i c 0789 Rot e l 0558, 0623 Row a 0759 Row n so n i c 0789 Roy a l 0690 Saba 0551 Saivod 0759 Salora 0741 Sampo 0752 Samsung 0199, 0490, 0573, 0744, 1044, 1075 Sansui 0695, 1228 Santosh 1115 Sanyo 0675, 0695, 0713, 1228 Scan 0850 Schaub Lorenz 0788, 1115 Schneider 0539, 0646, 0713, 0788, 0869 Schoentech 0713 Schwaiger 0752 Scott 0672, 1233 Seeltech 1224 SEG 0713 Semp 0503 Shanghai 0672 Sharp 0630, 0675, 0713, 0752, 1256 Sherwood 0741 Shinsonic 0533 Sigmatek 1224 Siltex 1224 Silva 0788, 0898 Silva Schneid er 0898 SilverCres t 1152 Singer 0690 Sistemas 0672 Skantic 0539, 0713 Skyworth 0898 Sliding 1115 SM Electronic 0690, 1152 Smart 0713 Sonic Blue 0573, 0869 Sony 0533, 0573, 0630, 0864, 1033, 1070, 1431, 1516, 1533 Sound Color 1233 Standard 0788, 0898 Star Clusters 1152, 1227 Starmedia 1224 Strong 0713 Sunkai 0850 Sunwood 0788, 0898 Superscan 0821 Super vision 1152 SV A 0672, 0752 Sylvania 0630, 0675, 0821 Symphonic 0675, 0821 T andberg 0713 Ta r g a 1227 Tc h i b o 0741 TCM 0741 Te a c 0571, 0675, 0741, 0759, 1227 Te c 0898 T echnics 0490, 0703 T echnika 1115 T echnisson 1115 T echnosonic 1115 T echwood 0713 T ecnimage n 1233 Te d e l e x 0690, 1228 T elefunken 0789 Te l e t e c h 0713 Te n s a i 0690 Te v i o n 0898, 1227 Theta Digital 0571 Thomson 0511, 0522, 0551 PRO-141FD_PRO-101FD.book Page 94 M onday, May 12, 2008 3 :27 PM
95 En 09 Appendix 9.1.7 LD Brand/Code Brand/Code Brand/Code Brand/Code Brand/Code Brand/Code To k a i 0788, 0898 To m - T e c 0789 To p S u x e s s 1224 To s h i b a 0503, 0539, 0573, 0695, 1154, 1769 TRANS- continents 1233 T red ex 0843 TSM 1224 Umax 0690 United 0675, 0695, 0713, 0788, 1115, 1152, 1228, 1233 Universum 0591, 0713, 0741, 0869, 1227 Urban Concepts 0503, 0539 Ve s t e l 0713 Vie w ma st e r 1224 Vo x s o n 0690 Vtrek 1228 Wa i t e c 1224, 1233 W ellington 0713 We l t s t a r 0713 Whar fedale 0713, 0752 Wil so n 1233 Win d so r 0713 Win d y S a m 0573 WIZE 1115 Wo x t e r 1224 Xbox 0522, 2083 XLogic 1152, 1228 XMS 0788 Ya k u m o 1056 Ya m a d a 1056 Ya m a h a 0490, 0539, 0545, 0646, 1282, 1354 Zenith 0503, 0591, 0741, 0869 Brand/Code Brand/Code Brand/Code Brand/Code Brand/Code Brand/Code Aiwa 0203 Car ver 0194 Denon 0059, 0172, 0241 Disco Vision 0023 F unai 0203 GoldStar 0172 Grundig 0059 Harman/Kardon 0194 Hitachi 0023 Magnavox 0194, 0217, 0241 Marantz 0194 Mitsubishi 0059, 0241 NAD 0059 Nagsmi 0059 Optimus 0059 P anasonic 0204 Philips 0194 Pioneer 0023, 0059, 0241, 1274 Po l k A u d i o 0194 Quasar 0204 Rea l i st i c 0203 Sega 0023 Sony 0201 T echnics 0204 T e lefunken 0059 Theta Digital 0194 To s h i b a 0059 Wa r d s 0059 Ya m a h a 0217 PRO-141FD_PRO-101FD.book Page 95 M onday, May 12, 2008 3 :27 PM
96 En 09 Appendix 9.2 Video/PC Signals (HDMI/DVI/ Component/min D-Sub/Composite) 9.2.1 INPUT 1 (Video Signals) 9.2.2 INPUT 2 (Component)/INPUT 3 (D-Sub) - Video Signals (Analog) When reproducing the analog signals in the ta ble below , set the Color Decoding option to Comp. 1 or Comp. 2 . Screen Mode Remark s DOT BY DOT 4:3 FULL (FULL1) FULL2 ZOOM CINEMA WIDE WID E 1 WIDE 2 FULL 14:9 CINEMA 14:9 N T S C - Ye s Ye s - Ye s Ye s Ye s - - Ye s Ye s P AL - Y es Y es - Y es Y es Y es - - Y es Y es SECAM - Y es Y es - Y es Y es Y es - - Y es Y es 4.43NTSC - Y es Y es - Y es Y es Y es - - Y es Y es P AL M - Y es Y es - Y es Y es Y es - - Y es Y es P AL N - Y es Y es - Y es Y es Y es - - Y es Y es Resolut ion Hf (kHz) Vf (Hz) Screen Mode Remarks DOT BY DOT 4:3 FULL (FULL1) FULL 2 ZOOM CINEMA WIDE WIDE 1 WIDE 2 FULL 14:9 CINEMA 14:9 480i 15.8 60.0 - Y es Y es - Y es Y es Y es - - Y es Y es 480p 31.5 60.0 - Y es Y es - Y es Y es Y es - - Y es Y es 576i 15.6 50.0 - Y es Y es - Y es Y es Y es - - Y es Y es 576p 31.3 50.0 - Y es Y es - Y es Y es Y es - - Y es Y es 720p 37.5 50.0 - Y es Y es - Y es - - Y es Y es - - 720p 45.0 60.0 - Y es Y es - Y es - - Y es Y es - - 1080i 28.1 50.0 Y es Y es Y es Y es Y es - - Y es Y es - - 1080i 33.8 60.0 Y es Y es Y es Y es Y es - - Y es Y es - - 1080p 27.0 24.0 Y es Y es Y es Y es Y es - - Y es Y es - - 1080p 56.3 50.0 Y es Y es Y es Y es Y es - - Y es Y es - - 1080p 67.5 60.0 Y es Y es Y es Y es Y es - - Y es Y es - - PRO-141FD_PRO-101FD.book Page 96 M onday, May 12, 2008 3 :27 PM
97 En 09 Appendix 9.2.3 INPUT 4 (DVI)/INPUT 5 through 8 (HDMI) - Video Signals (Digital) When reproducing the digital signals in the ta ble below , set the Signal T ype option to Vid e o . Resoluti on Hf (kHz) Vf (Hz) Screen Mode Remarks DOT BY DOT 4:3 FULL (FULL1) FULL 2 ZOOM CINEMA WIDE WIDE 1 WIDE 2 FULL 14:9 CINEMA 14:9 480i 15.8 60.0 - Y es Y es - Y es Y es Y es - - Y es Y es 480p 31.5 60.0 - Y es Y es - Y es Y es Y es - - Y es Y es 576i 15.6 50.0 - Y es Y es - Y es Y es Y es - - Y es Y es 576p 31.3 50.0 - Y es Y es - Y es Y es Y es - - Y es Y es 720p 37.5 50.0 - Y es Y es - Y es - - Y es Y es - - 720p 45.0 60.0 - Y es Y es - Y es - - Y es Y es - - 1080i 28.1 50.0 Y es Y es Y es Y es Y es - - Y es Y es - - 1080i 33.8 60.0 Y es Y es Y es Y es Y es - - Y es Y es - - 1080p 27.0 24.0 Y es Y es Y es Y es Y es - - Y es Y es - - 1080p 56.3 50.0 Y es Y es Y es Y es Y es - - Y es Y es - - 1080p 67.5 60.0 Y es Y es Y es Y es Y es - - Y es Y es - - PRO-141FD_PRO-101FD.book Page 97 M onday, May 12, 2008 3 :27 PM
98 En 09 Appendix 9.2.4 INPUT 3 (D-Sub ) - PC Signals (A nalog) When reproducing the an alog signals in the table below , set the Co lor Decoding option to RGB . If the pictu re does not appear properly , change the Signal Fo rmat sett ing to the desired r esolution. Resolution Dot-Line Hf (kHz) Vf (Hz) Screen Mode Remarks DOT BY DOT 4:3 FULL (FULL1) FULL2 ZOOM CINEMA WIDE WIDE 1 WIDE 2 FULL 14:9 CINEMA 14:9 720 ÃÂ 400 31.5 70.1 - Y es Y es - - - - - - - - 640 ÃÂ 480 31.5 59.9 - Y es Y es - - - - - - - - 640 ÃÂ 480 35.0 66.7 - Y es Y es - - - - - - - - Apple Macint osh 13 640 ÃÂ 480 37.9 72.8 - Y es Y es - - - - - - - - 640 ÃÂ 480 37.5 75.0 - Y es Y es - - - - - - - - 640 ÃÂ 480 43.3 85.0 - Y es Y es - - - - - - - - 720 ÃÂ 480 31.5 60.0 - Y es Y es - - - - - - - - 720 ÃÂ 480 27.2 71.9 - Y es Y es - - - - - - - - 848 ÃÂ 480 31.0 60.0 - Y es Y es - - - - - - - - 800 ÃÂ 600 35.2 56.3 - Y es Y es - - - - - - - - 800 ÃÂ 600 37.9 60.3 - Y es Y es - - - - - - - - 800 ÃÂ 600 48.1 72.2 - Y es Y es - - - - - - - - 800 ÃÂ 600 46.9 75.0 - Y es Y es - - - - - - - - 800 ÃÂ 600 53.7 85.1 - Y es Y es - - - - - - - - 832 ÃÂ 624 49.7 74.6 - Y es Y es - - - - - - - - Apple Macint osh 16 1280 ÃÂ 720 44.8 60. 0 - Y es Y es - - - - - - - - 1280 ÃÂ 720 18.4 71. 9 - Y es Y es - - - - - - - - 1360 ÃÂ 768 47.7 60. 0 - Y es Y es - - - - - - - - 1280 ÃÂ 768 47.8 59. 9 - Y es Y es - - - - - - - - 1024 ÃÂ 768 48.4 60. 0 - Y es Y es - - - - - - - - 1024 ÃÂ 768 56.5 70. 1 - Y es Y es - - - - - - - - 1024 ÃÂ 768 60.0 75. 0 - Y es Y es - - - - - - - - 1024 ÃÂ 768 68.7 85. 0 - Y es Y es - - - - - - - - 1024 ÃÂ 768 58.0 71. 9 - Y es Y es - - - - - - - - 1024 ÃÂ 768 60.2 74. 9 - Y es Y es - - - - - - - - Apple Macint osh 19 1280 ÃÂ 768 56.0 69. 8 - Y es Y es - - - - - - - - CVT 1280 ÃÂ 768 57.8 72. 1 - Y es Y es - - - - - - - - 1280 ÃÂ 800 49.7 60. 0 - Y es Y es - - - - - - - - 1152 ÃÂ 864 53.7 60. 0 - Y es Y es - - - - - - - - 1152 ÃÂ 864 67.5 75. 0 - Y es Y es - - - - - - - - PRO-141FD_PRO-101FD.book Page 98 M onday, May 12, 2008 3 :27 PM
99 En 09 Appendix 9.2.5 INPUT 4 (DVI)/INPUT 5 through 8 (HDMI) - PC Signals (Digital) When reproducing the digital signals in the ta ble below , set the Signal T yp e option to PC . If the picture does n ot appear properly , change the Signal F orm at setting to the desired resolution. 1152 ÃÂ 870 68.7 75.1 - Y es Y es - - - - - - - - Apple Macintos h 21 1280 ÃÂ 960 60.0 60.0 - Y es Y es - - - - - - - - 1280 ÃÂ 960 85.9 85.0 - Y es Y es - - - - - - - - 1280 ÃÂ 1024 64.0 60.0 - Y es Y es - - - - - - - - 1280 ÃÂ 1024 80.0 75.0 - Y es Y es - - - - - - - - 1440 ÃÂ 900 56.0 60.0 - Y es Y es - - - - - - - - Apple Macintos h 17 1400 ÃÂ 1050 65.3 60.0 - Y es Y es - - - - - - - - CVT 1400 ÃÂ 1050 82.3 74.9 - Y es Y es - - - - - - - - 1400 ÃÂ 1050 93.9 85.0 - Y es Y es - - - - - - - - 1680 ÃÂ 1050 65.3 60.0 - Y es Y es - - - - - - - - 1280 ÃÂ 1024 91.1 85.0 - Y es Y es - - - - - - - - 1920 ÃÂ 1080 67.5 60.0 - Y es Y es - - - - - - - - 1600 ÃÂ 1200 75.0 60.0 - Y es Y es - - - - - - - - 1600 ÃÂ 1200 81.3 65.0 - Y es Y es - - - - - - - - 1600 ÃÂ 1200 87.5 70.0 - Y es Y es - - - - - - - - 1600 ÃÂ 1200 93.8 75.0 - Y es Y es - - - - - - - - 1600 ÃÂ 1200 106.3 85.0 - Y es Y es - - - - - - - - 1920 ÃÂ 1200 74.6 60.0 - Y es Y es - - - - - - - - 1920 ÃÂ 1200RB 74.0 60.0 - Y es Y es - - - - - - - - Resolution Dot-Line Hf (kHz) Vf (Hz) Screen Mode Remarks DOT BY DOT 4:3 FULL (FULL1) FULL2 ZOOM CINEMA WIDE WIDE 1 WIDE 2 FULL 14:9 CINEMA 14:9 720 ÃÂ 400 31.5 70.1 - Y es Y es - - - - - - - - 640 ÃÂ 480 31.5 59.9 - Y es Y es - - - - - - - - 640 ÃÂ 480 37.9 72.8 - Y es Y es - - - - - - - - 640 ÃÂ 480 37.5 75.0 - Y es Y es - - - - - - - - 640 ÃÂ 480 43.3 85.0 - Y es Y es - - - - - - - - 848 ÃÂ 480 31.0 60.0 - Y es Y es - - - - - - - - 800 ÃÂ 600 35.2 56.3 - Y es Y es - - - - - - - - 800 ÃÂ 600 37.9 60.3 - Y es Y es - - - - - - - - Resolution Dot-Line Hf (kHz) Vf (Hz) Screen Mode Remarks DOT BY DOT 4:3 FULL (FULL1) FULL2 ZOOM CINEMA WIDE WIDE 1 WIDE 2 FULL 14:9 CINEMA 14:9 PRO-141FD_PRO-101FD.book Page 99 M onday, May 12, 2008 3 :27 PM
100 En 09 Appendix Banner PIP supports 1360 x 768 and 1024 x 768 signals. 800 ÃÂ 600 48.1 72.2 - Y es Y es - - - - - - - - 800 ÃÂ 600 46.9 75.0 - Y es Y es - - - - - - - - 800 ÃÂ 600 53.7 85.1 - Y es Y es - - - - - - - - 1360 ÃÂ 768 47.7 60. 0 - Y es Y es - - - - - - - - 1280 ÃÂ 768 47.8 59. 9 - Y es Y es - - - - - - - - 1024 ÃÂ 768 48.4 60. 0 - Y es Y es - - - - - - - - 1024 ÃÂ 768 56.5 70. 1 - Y es Y es - - - - - - - - 1024 ÃÂ 768 60.0 75. 0 - Y es Y es - - - - - - - - 1024 ÃÂ 768 68.7 85. 0 - Y es Y es - - - - - - - - 1024 ÃÂ 768 58.0 71. 9 - Y es Y es - - - - - - - - 1280 ÃÂ 768 56.0 69. 8 - Y es Y es - - - - - - - - CVT 1280 ÃÂ 768 57.8 72. 1 - Y es Y es - - - - - - - - 1280 ÃÂ 800 49.7 60. 0 - Y es Y es - - - - - - - - 1152 ÃÂ 864 53.7 60. 0 - Y es Y es - - - - - - - - 1152 ÃÂ 864 67.5 75. 0 - Y es Y es - - - - - - - - 1280 ÃÂ 960 60.0 60. 0 - Y es Y es - - - - - - - - 1280 ÃÂ 960 85.9 85. 0 - Y es Y es - - - - - - - - 1280 ÃÂ 1024 64.0 60. 0 - Y es Y es - - - - - - - - 1280 ÃÂ 1024 80.0 75. 0 - Y es Y es - - - - - - - - 1440 ÃÂ 900 56.0 60. 0 - Y es Y es - - - - - - - - Apple Macint osh 17 1400 ÃÂ 1050 65.3 60. 0 - Y es Y es - - - - - - - - CVT 1400 ÃÂ 1050 82.3 74. 9 - Y es Y es - - - - - - - - 1680 ÃÂ 1050 65.3 60. 0 - Y es Y es - - - - - - - - 1280 ÃÂ 1024 91.1 85. 0 - Y es Y es - - - - - - - - 1600 ÃÂ 1200 75.0 60. 0 - Y es Y es - - - - - - - - 1920 ÃÂ 1200RB 74.0 60. 0 - Y es Y es - - - - - - - - Resolution Dot-Line Hf (kHz) Vf (Hz) Screen Mode Remarks DOT BY DOT 4:3 FULL (FULL1) FULL2 ZOOM CINEMA WIDE WIDE 1 WIDE 2 FULL 14:9 CINEMA 14:9 PRO-141FD_PRO-101FD.book Page 100 Monday, May 12, 2008 3:27 PM
101 En 09 Appendix 9.3 Specifications F or specifications, see the se parate Specifications Sheet. PRO-141FD_PRO-101FD.book Page 101 Monday, May 12, 2008 3:27 PM
102 En 09 Appendix 9.4 Trademarks Trademarks Ã¢ÂÂ¢ HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. Ã¢ÂÂ¢ Apple and Macintosh are regist ered trademarks of Apple Inc. Ã¢ÂÂ¢ Microsoft is a registered trad emark of Microsoft Corporation. Ã¢ÂÂ¢ VESA and DDC are registered trademarks of Video Electronics Standards Association. Ã¢ÂÂ¢ Power Management and Sun Microsystems are regi stered trademarks of Sun Microsystem s, Inc. Ã¢ÂÂ¢ VGA and XGA are registered trademark s of International Business Machines Co., Inc. PRO-141FD_PRO-101FD.book Page 102 Monday, May 12, 2008 3:27 PM
103 En 09 Appendix 9.5 Glossary VGA (Video Graphics Ar ray) VGA is used for a resolution of 640 x 480. Wide-VGA (Wide Vi deo Graphics Array) Wide- VGA is used for a resolution of 848 x 480. SVGA (Super Video Gr aphics Array) SVGA is used for a resolution of 800 x 600. XGA (eXtended Gr aphics Array) XGA is used for a resolution of 1024 x 768. Wide-XGA (Wide eXtended Graphics Array) Wide -XGA is used for a resolution of 1280 x 768. SXGA (Super eXtended Graphics Array) SXGA is used for a resolution of 1280 x 1024. SXGA (Super eXtended Graphics A rray ) SXGA is used for a resolution of 1400 x 1050. Wide-SXGA (Wide Super eX tended Graphics Arr ay) Wide-SXGA i s used for a resolution of 1680 x 1050. UXGA (Ultra eXtended Gr aphics Array) UXGA is used for a resolution of 1600 x 1200. Wide-UXGA (Wide Ultra eXt ended Graphics Arr ay) Wide-UXGA i s used for a resolution of 1920 x 1200. DVI The Digital V isual Inte r face (DVI) is a video interface standard deve loped by an industr y consortium, the Digital Display Working Group (DDWG). DVI is de signed to m aximize the visual quality of digital display devices such as a flat panel display . HDMI The High-Definition Multimed ia Inter face (HDMI) is a digital data transmission standard for consumer electronics/home appliances. HDMI connects digital audi o/video sou rces to a compatible digital audio an d/or video device, such as a flat panel display . H DMI also a llows digitally transmitted au dio and control signals on a single cable for multi-chan nel digital audio s ources. Component video signal General term for video s i g n a l f o r m a t c o m p o s e d o f t h e Y. C B C R , Y. P B P R a n d Y. B - Y. R - Y l u m i n a n c e s i g n a l c o l o r signal. The component video signal is sometimes simply called the "color difference signal." PRO-141FD_PRO-101FD.book Page 103 Monday, May 12, 2008 3:27 PM
104 En 09 Appendix DHCP The Dynamic Host Configuration P rotocol (DHCP) prov ides a mechanism to automa tically allocate network settings such as IP Address, Defaul t Gateway and Subnet mask. A DHCP ser v er must be activa ted on a network to use the DHCP function . DNS The Domain Name Ser vice (DNS) ser ver functions to exchange IP Address to the hostna me, hostname to the IP Address. POP before SMTP POP before SMTP is a method of authorizat ion using PO P (P ost Office P rotocol) before sending an E-mail via SMTP (Simple Mail T ransfer P rotocol). SMTP The Simple Mail T ransfer Pr otocol (SMT P) is a text-based protocol in whic h a message is transferred between a client and ser ver or between ser vers. PRO-141FD_PRO-101FD.book Page 104 Monday, May 12, 2008 3:27 PM
105 En Appendix 09 9.6 Index Numerics 2-screen ................. .................... .................... .................... 10, 11, 43 A Auto Size ..... .................... .................... .................... .......... 28, 3 3, 36 AV Selection .................... ......................... .................... ........... 3 1, 32 B Blue .................. ......................... .................... .................... ............ 35 Brightness ............. ......................... .................... .................... ....... 35 Brightness Sync ... .................... .................... .................... ...... 37, 77 C CBL ................... ......................... .................... .................... ...... 10, 49 Color ................. ......................... .................... .................... 25, 3 2, 35 Contrast .. .................... .................... .................... ......... 25, 31, 32, 35 E Energy Save .......... .................... .................... .................... 28, 29, 45 F Film Mode ... .................... .................... .................... ...................... 3 8 Freeze ............... .................... .................... .................... ........... 44, 80 G GAME ..... .................... .................... .................... ......... 18, 31, 39, 62 Game Control Pref. .............. ......................... ......................... ....... 39 Green ................ .................... .................... .................... ........... 35, 51 H HD Wide Mode .......... .................... .................... .................... ....... 36 HDMI Input ........... .................... .................... .................... ............ 54 HDMI port ....................... .................... .................... .................... .. 56 HDMI terminal . .................... .................... ......................... ...... 18, 54 HOME MENU ........ .................... .................... .................... ............ 10 I Input ............ ......................... .................... .................... ................. 1 0 Installation ...................... ......................... ......................... ...... 12, 80 K KURO LINK . .................... .................... ......................... ........... 54, 5 6 KURO LINK Setting ........ .................... .................... ...................... 5 8 L Language ................... ......................... .................... ................ 2 4, 56 Long Life Settings . .................... .................... .................... 28, 76, 82 M MOVIE ................... ......................... .................... ............... 10, 27, 31 multi-screen .................... ......................... .................... ........... 4 3, 44 O OPTIMUM .................. ......................... .................... ................ 1 0, 3 1 Orbiter .............. .................... .................... .................... ........... 29, 82 P Picture-in-picture ...................... ......................... ............... 10, 11, 43 Position ................. .................... .................... .................... ............ 26 Power .................... ......................... .................... ............... 21, 29, 45 Power Control ............ .................... .................... .................... ....... 62 Power Management .. .................... .................... .................... ....... 45 R Red ................... .................... .................... .................... ................. 3 5 Remote Control ....................................... .................... ....... 8, 10, 46 Room Light Sensor .............. ......................... ......................... ....... 25 S SAT ................... ......................... .................... .................... ...... 10, 49 SCREEN SIZE ....................... .................... .................... ........... 11, 3 3 Sharpness .................. .................... .................... .................... . 32, 35 SHIFT ................ ......................... .................... .................... ...... 11, 43 Side Mask .................. .................... .................... .................... . 28, 37 Side Mask Detection ...... .................... .................... ...................... 3 6 Sleep Timer ...... .................... .................... .................... ................. 30 SPORT .................. ......................... .................... .................... ..10, 31 STANDARD ......................... .................... .................... ......10, 31, 32 SWAP ................... ......................... .................... .................... ..11, 43 T Text Optimization ........... .................... .................... ..................... . 38 Tint ................... ......................... .................... .................... ............ 35 U USER ............... .................... .................... .................... ......10, 31 , 32 USER MENU ....................... .................... .................... ................. 23 PRO-141FD_PRO-101FD.book Page 105 Monday, May 12, 2008 3:27 PM
<ARB1581-A> Printed in China Published by Pioneer Corporation. Copyright ÃÂ© 2008 Pioneer Corporation. All rights reserved. PIONEER CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. BOX 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404 PIONEER ELECTRONICS OF CANADA, INC. 300 Allstate Parkway, Markham, Ontario L3R 0P2, Canada TEL: 1-877-283-5901, 905-479-4411 PIONEER EUROPE NV Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11 PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555 PIONEER ELECTRONICS AUSTRALIA PTY. LTD. 178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: (03) 9586-6300 PIONEER ELECTRONICS DE MEXICO S.A. DE C.V. Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico, D.F. 11000 TEL: 55-9178-4270 K002_B_En Register Your Product on http://www.pioneerelectronics.com (US) http://www.pioneerelectronics.ca (Canada)